GemTek Technology WVVDB-101N 7130 Residential Gateway 6Vz.A2131 User Manual 6Ve AB2131

Gemtek Technology Co., Ltd. 7130 Residential Gateway 6Vz.A2131 6Ve AB2131

User Manual

CellPipe® 7130VDSL RESIDENTIAL GATEWAY6Vz.A2131,6Ve.B2131 | RELEASE 1.0USER MANUAL3EQ-10280-AAAA-TCZZAEDITION 01FEBRUARY 2011
Alcatel, Lucent, Alcatel-Lucent, the Alcatel-Lucent logo, and CellPipe are trademarks of Alcatel-Lucent. All other trademarks are the property of their respective owners.The information presented is subject to change without notice. Alcatel-Lucent assumes no responsibility for inaccuracies contained herein.Alcatel-Lucent provides this documentation without warranty of any kind, implied or expressed, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Copyright © 2010 Alcatel-Lucent. All rights reserved.Conformance statementsThe equipment has been tested in the regulation lab and complied with the limits for VDSL device, pursuant to Europe CE/CB, Australia A-Trick and China CCC. These limits of different regulations are designed provide reasonable protection against harmful interference or damage in a residential installation.Security statement In rare instances, unauthorized individuals make connections to the telecommunications network through the use of remote access features. In such an event, applicable tariffs require the customer to pay all network charges for traffic. Alcatel-Lucent cannot be responsible for such charges and will not make any allowance or give any credit for charges that result from unauthorized access.IMPORTANT NOTICE: This document contains confidential information that is proprietary to Alcatel-Lucent. No part of its contents may be used, copied, disclosed or conveyed to any party in any manner whatsoever without prior written permission from Alcatel-Lucent.www.alcatel-lucent.com
iii3EQ-10280-AAAA-TCZZAEdition 01 February 2011............................................................................................................................................................................................................................................................About this documentPurposeThis document provides information on the hardware setup, software configuration, and administration necessary to operate the CellPipe 7130 Residential Gateway 6Vz.A2131/ 6Ve.B2131.Reason for revisionThe following table shows the revision history of this document.Intended audienceThis document is intended for users and administrators of the CellPipe 7130 RG 6Vz.A2131/6Ve.B2131.How to use this documentThis document introduces the CellPipe 7130 RG 6Vz.A2131/6Ve.B2131 hardware, connections, and setup. It also explains the web configuration interface and provides parameter definitions for the fields that appear on those windows.Conventions usedThis guide uses the following typographical conventions:Revision Date Reason for reissueEdition 01 February 2011 First release of this documentAppearance DescriptionItalicized text •File and directory names.•Emphasized information.•Titles of publications.•A value that the user supplies.graphical user interface text or key name•Text that is displayed in a graphical user interface or in a hardware label.•The name of a key on the keyboard.
............................................................................................................................................................................................................................................................About this documentiv 3EQ-10280-AAAA-TCZZAEdition 01 February 2011............................................................................................................................................................................................................................................................Structure of hazard statementsOverviewFor the safety of you and your equipment, this document contains hazard statements. Hazard statements are given at points where there may be a risk of damage to personnel, equipment, or operation. Failure to follow the directions in a hazard statement may result in personal harm, equipment damage, or network loss.General structureHazard statements include the structural elements shown in the figure below.Structure of hazard statementsinput text Command names and text that the user types or selects as input to a system.output text Text that a system displays or prints.Press the Return or Enter key on the keyboard.Appearance DescriptionItem Structure element Purpose1 Personal injury symbol Indicates the potential for personal injury (optional).2 Hazard type symbol Indicates hazard type (optional).3 Signal word Indicates the severity of the hazard.4 Hazard type Describes the source of the risk of damage or injury.5 Damage statement Consequences if protective measures fail.6 Avoidance message Protective measures to take to avoid the hazard.7 Identifier The reference ID of the hazard statement (optional).
About this document............................................................................................................................................................................................................................................................3EQ-10280-AAAA-TCZZAEdition 01 February 2011 v............................................................................................................................................................................................................................................................Signal wordsThe following table defines signal words that identify the hazard severity levels.Signal words for hazard severityRelated information The documentation set accompanying this family of routers includes this User Manual and a Quick Installation Guide.Technical supportFor technical support, contact your local Alcatel-Lucent customer support team. See the Alcatel-Lucent Support website (http://alcatel-lucent.com/support/) for contact information.Signal word MeaningDANGER Indicates an imminently hazardous situation (high risk) which, if not avoided, will result in death or serious injury.WARNING Indicates a potentially hazardous situation (medium risk) which, if not avoided, could result in death or serious injury.CAUTION When used with the personal injury symbol:Indicates a potentially hazardous situation (low risk) which, if not avoided, may result in personal injury.When used without the personal injury symbol: Indicates a potentially hazardous situation (low risk) which, if not avoided, may result in property damage, such as service interruption or damage to equipment or other materials.
............................................................................................................................................................................................................................................................About this documentvi 3EQ-10280-AAAA-TCZZAEdition 01 February 2011............................................................................................................................................................................................................................................................
vii3EQ-10280-AAAA-TCZZAEdition 01 February 2011............................................................................................................................................................................................................................................................Contents1Product overviewHardware introduction ............................................................................................................................... 1-1Safety precautions ..................................................................................................................................... 1-2Prerequisites .............................................................................................................................................. 1-3Description of LEDs and interfaces .......................................................................................................... 1-32 Hardware installationTo mount the CellPipe 7130 RG ............................................................................................................... 2-1To install the CellPipe 7130 RG ................................................................................................................ 2-2RGAM installation of the Residential Gateway Application Module .......................................................2-43 Accessing the CellPipe 7130 RG web configuration toolTo access the CellPipe 7130 RG web configuration tool ..........................................................................3-14 StatusSystem Usage ............................................................................................................................................ 4-1WAN PTM Status ...................................................................................................................................... 4-3DSL Link Status ........................................................................................................................................ 4-4Device Table .............................................................................................................................................. 4-6DHCP Lease .............................................................................................................................................. 4-7WiFi Association .......................................................................................................................................4-8WAN/(W)LAN Statistics ........................................................................................................................... 4-8IGMP Membership .................................................................................................................................. 4-10IGMP Statistics ........................................................................................................................................ 4-10 ................................................................................................................................................................. 4-115NetworkUSB ........................................................................................................................................................... 5-1LAN Settings ............................................................................................................................................. 5-3WAN Link Selection ................................................................................................................................. 5-6WAN PTM Connections ............................................................................................................................ 5-6 ................................................................................................................................................................. 5-316WiFi setupWiFi Settings ............................................................................................................................................. 6-1WiFi Security ............................................................................................................................................. 6-4
............................................................................................................................................................................................................................................................Contentsviii 3EQ-10280-AAAA-TCZZAEdition 01 February 2011............................................................................................................................................................................................................................................................WiFi Access Filter ..................................................................................................................................... 6-67 Firewall setupPort Forwarding ........................................................................................................................................ 7-1Demilitarized Zone .................................................................................................................................... 7-3UPnP ......................................................................................................................................................... 7-4Layer 2 Filter ............................................................................................................................................. 7-5Layer 3 Filter ............................................................................................................................................. 7-7NAT Passthrough ...................................................................................................................................... 7-8URL Blocking ........................................................................................................................................... 7-9Content Screening ................................................................................................................................... 7-10Parental Control ...................................................................................................................................... 7-118Advanced setupRoute Settings ........................................................................................................................................... 8-1DNS Settings ............................................................................................................................................. 8-3Dynamic DNS ........................................................................................................................................... 8-4System Log ................................................................................................................................................ 8-5IGMP Proxy/Snooping .............................................................................................................................. 8-6802.1x Config ............................................................................................................................................ 8-79QoS PTM setupQoS Overview ........................................................................................................................................... 9-1QoS Scheduler ........................................................................................................................................... 9-2 ................................................................................................................................................................... 9-4QoS Policy ................................................................................................................................................ 9-5QoS Phone ................................................................................................................................................. 9-7QoS ALG .................................................................................................................................................. 9-8QoS Defaults ........................................................................................................................................... 9-10QoS MAC ................................................................................................................................................ 9-1210 TelephonyAccount Setup ......................................................................................................................................... 10-1Service Settings ....................................................................................................................................... 10-4SIP Server Settings .................................................................................................................................. 10-8RTP/Codecs settings .............................................................................................................................. 10-10Account & Line Table ........................................................................................................................... 10-12Call History ........................................................................................................................................... 10-13Other Settings ........................................................................................................................................ 10-14
Contentsix3EQ-10280-AAAA-TCZZAEdition 01 February 2011........................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................11 UtilitiesConfiguration Backup ..............................................................................................................................11-1Configuration Restore ..............................................................................................................................11-2Firmware Upgrade ...................................................................................................................................11-3System Settings ........................................................................................................................................11-4Management Access Control ................................................................................................................... 11-7CWMP Management ...............................................................................................................................11-8Connection Test .....................................................................................................................................11-10802.1x CA Upload ................................................................................................................................. 11-11Restore Factory Defaults ....................................................................................................................... 11-11Reboot Gateway .....................................................................................................................................11-12RGAM Management .............................................................................................................................11-13A TroubleshootingB TCP/IP configurationC Product conformanceEU declaration of conformity ................................................................................................................... C-1FCC 15B statement ................................................................................................................................... C-3FCC Part 68 Statement ............................................................................................................................. C-4Industry Canada statement ........................................................................................................................ C-5IC TELECOM .......................................................................................................................................... C-5GL Glossary
............................................................................................................................................................................................................................................................Contentsx 3EQ-10280-AAAA-TCZZAEdition 01 February 2011............................................................................................................................................................................................................................................................
1-13EQ-1028-AAAA-TCZZAEdition 01 February 2011............................................................................................................................................................................................................................................................1Product overviewOverviewPurposeThis chapter provides an introduction to the physical aspects of the CellPipe 7130 RG 6Vz.A2131/6Ve.B2131 including safety precautions and features.The CellPipe 7130 RG 6Vz.A2131/6Ve.B2131 will be referred to as CellPipe 7130 RG throughout the rest of this document.ContentsThis chapter covers the following topics:Hardware introductionThe CellPipe 7130 RG connects residential users to a broadband WAN via an Ethernet-over-VDSL link or a Gigabit Ethernet connection. For this purpose, it provides the following WAN interfaces:•one VDSL port•one Gigabit Ethernet portNote: The WAN interfaces cannot be used concurrently.The devices on the LAN of residential users are interconnected and connected to the WAN via IP routing or Ethernet bridging. The following interfaces can be used to connect devices in the home:•Four Gigabit Ethernet LAN ports (10/100/1000Base-TX)Hardware introduction 1-1Safety precautions 1-2Prerequisites 1-3Description of LEDs and interfaces 1-3
............................................................................................................................................................................................................................................................Safety precautionsProduct overview1-2 3EQ-1028-AAAA-TCZZAEdition 01 February 2011............................................................................................................................................................................................................................................................•wireless access point Safety precautionsWARNINGRisk of electric shock or fire1. Pay attention to the power load of the electrical outlet or extension cord. An overburdened power outlet or damaged cords and plugs may cause electric shock or fire. Check the power cords regularly. If you find any damage, replace the cord immediately.2. Leave adequate space for heat dissipation to avoid any damage caused by overheating the CellPipe 7130 RG. Do not cover the ventilation holes. Blocking the ventilation holes may cause fire.3. When connecting a PC or other electronic device to the CellPipe 7130 RG, make sure you use the right cables and connect the device to the right port of the CellPipe 7130 RG. Incorrect connections may damage the device and/or CellPipe 7130 RG..CAUTIONPotential equipment damageFollow these recommendations to protect yourself and the CellPipe 7130 RG from harm:1. Do not insert any sharp object into the openings of the CellPipe 7130 RG..2. Never install telephone wiring during inclement weather; for example, during a storm.3. Electrostatic discharge (ESD) can permanently damage semiconductor devices. Always follow ESD-prevention guidelines for equipment handling and storage.4. Use the power adapter provided with the CellPipe 7130 RG and do not fasten the power cable to building surfaces. Ensure the cable can move freely. Do not place heavy objects on the cable. Check the power cords regularly. If you find any damage, replace the cord immediately.5. Do not put the CellPipe 7130 RG near a heat source. Avoid placing the CellPipe 7130 RG in direct sunlight.6. Do not put the CellPipe 7130 RG in damp or wet locations. Do not spill any liquid on the CellPipe 7130 RG..7. Do not place the CellPipe 7130 RG on an unstable surface or support.8. Do not place heavy objects on top of the CellPipe 7130 RG..9. Do not use liquid or aerosol cleaners; use a soft, dry cloth for cleaning.
Product overviewPrerequisites............................................................................................................................................................................................................................................................3EQ-1028-AAAA-TCZZAEdition 01 February 2011 1-3............................................................................................................................................................................................................................................................PrerequisitesEnsure that you have the following items before attempting to use the CellPipe 7130 RG:•Internet services subscription (connection type, account information, and addresses)•10/100Base-T Ethernet NIC installed in your PC•Operating system: Windows 98SE, Windows 2000, Windows NT, Windows ME, Windows XP, Windows Vista, Windows 7, or Mac OS•Internet Explorer v4.0 or higher, Netscape v4.0 or higher, or Mozilla Firefox v1.5 or higherNote: For optimal display quality, use Internet Explorer v5.0 or Netscape v6.1.Description of LEDs and interfacesFigure 1-1 Front panelTable 1-1 Front panel LEDsLED Status DescriptionInternet On The CellPipe 7130 RG is connected to the Internet.Flashing Data is being transmitted over the Internet connection.Off The CellPipe 7130 RG is not connected to the Internet.DSL On DSL is operating.Flashing DSL is training.Off DSL is disconnected.
............................................................................................................................................................................................................................................................Description of LEDs and interfacesProduct overview1-4 3EQ-1028-AAAA-TCZZAEdition 01 February 2011............................................................................................................................................................................................................................................................GigE WAN On Gigabit Ethernet WAN link is up.Flashing Data is being transmitted on the Gigabit Ethernet WAN link.Off Gigabit Ethernet WAN is disconnected.USB 1 to 2 On A device is connected to the USB port.Flashing USB port has data traffic.Off No device is connected to USB port.WLAN2.4GHz On Wireless function is enabled.Flashing Data is being transmitted on the wireless link.Off Wireless function is disabled.WPS On WPS is enabled.Off WPS is disabled.LAN 1 to 4 On Ethernet LAN port 1 to 4 is connected and active.Flashing Network activity over the corresponding ports.Off Ethernet LAN port 1 to 4 is not active.Phone 1 to 2 On Phone 1 to 2 is connected.Off No phones are connected.Message Slow flashing*Firmware upgrade in progress.Off No firmware upgrade in progress.Power On CellPipe 7130 RG is powered on.Off Power is disconnected.Notes:* Slow flashing: LED flashes at the rate of 2 seconds on and 2 seconds off.LED Status Description
Product overviewDescription of LEDs and interfaces............................................................................................................................................................................................................................................................3EQ-1028-AAAA-TCZZAEdition 01 February 2011 1-5............................................................................................................................................................................................................................................................Figure 1-2 Rear panel of 6Vz.A2131Figure 1-3 Rear panel of 6Ve.B2131Table 1-2 Rear panel itemsItem DescriptionWireless AntennaeAntennae for transmission of wireless signal.DSL Port DSL network connection from your ISP. The DSL port connects to an RJ-11 cable (only for 6Vz.A2131). The DSL port connects to an TAE-RJ45 cable (only for 6Ve.B2131).Ethernet LAN1 to LAN4Four RJ-45 ports to connect up to four PCs or a Hub.GigE WAN Ethernet network connection from your ISP. The GigE WAN port connects to an RJ-45 cable.Note: The GigE Ethernet port cannot be used simultaneously with the DSL port.
............................................................................................................................................................................................................................................................Description of LEDs and interfacesProduct overview1-6 3EQ-1028-AAAA-TCZZAEdition 01 February 2011............................................................................................................................................................................................................................................................USB Support USB 2.0 for file sharing, printer sharing, UPnP digital Media sharing and sensor network interface support.HPNA (only for 6Vz.A2131)One HPNA interface to connect to a HPNA device.Phone 1 to 2 (only for 6Vz.A2131)Two RJ-11 ports for connecting telephones for VoIP.Reset Button Press and release to reboot the CellPipe 7130 RG. Press and hold for 10 seconds to restore to factory default settings.Power Switch Power On/Off switch.15VDC 2.4A DC power adapter port.TAE (only for 6Ve.B2131)Slot to insert the CellPipe 7130 Residential Gateway Application Module . See Figure 1-4Item Description
Product overviewDescription of LEDs and interfaces............................................................................................................................................................................................................................................................3EQ-1028-AAAA-TCZZAEdition 01 February 2011 1-7............................................................................................................................................................................................................................................................Figure 1-4 TAE interface for the CellPipe 7130 6Ve.B2131 residential gateway
............................................................................................................................................................................................................................................................Description of LEDs and interfacesProduct overview1-8 3EQ-1028-AAAA-TCZZAEdition 01 February 2011............................................................................................................................................................................................................................................................Figure 1-5 Front side of 6Ve.B2131Table 1-3 Front side itemsItem DescriptionWPS Activates the Wireless Protected Setup (WPS) functionWLAN 2.4GHzButton to activate and de-activation the Wireless interface.TAE (only for 6Ve.B2131)TAE phone connector
Product overviewDescription of LEDs and interfaces............................................................................................................................................................................................................................................................3EQ-1028-AAAA-TCZZAEdition 01 February 2011 1-9............................................................................................................................................................................................................................................................
............................................................................................................................................................................................................................................................Description of LEDs and interfacesProduct overview1-10 3EQ-1028-AAAA-TCZZAEdition 01 February 2011............................................................................................................................................................................................................................................................
2-13EQ-10280-AAAA-TCZZAEdition 01 February 2011............................................................................................................................................................................................................................................................2 Hardware installationOverviewPurposeThis chapter provides the instructions to install the CellPipe 7130 RG hardware.ContentsThis chapter covers the following topics:To mount the CellPipe 7130 RGThere are three ways to mount the CellPipe 7130 RG:•wall mounting•desktop mounting•stand-up mountingWall mountingPre-Requirements•Anchors•Screws•Drill & Drill bit1. Locate a high position on the wall that is free of obstructions and insert two screws in the wall 5 cm (2 in.) apart. Do not insert the screws all the way into the wall.To mount the CellPipe 7130 RG 2-1To install the CellPipe 7130 RG 2-2RGAM installation of the Residential Gateway Application Module 2-4
............................................................................................................................................................................................................................................................To install the CellPipe 7130 RGHardware installation2-2 3EQ-10280-AAAA-TCZZAEdition 01 February 2011............................................................................................................................................................................................................................................................Important! Make sure that the screws are securely fixed to the wall and strong enough to hold the weight of the CellPipe 7130 RG (recommended screw type and size: Nylon wall plug [T8x25mm] and screws [T3.5x16mm]).2. Align the holes on the back of the CellPipe 7130 RG with the screws on the wall and then hang the CellPipe 7130 RG on the screws.........................................................................................................................................................END OF STEPSDesktop mountingPlace the CellPipe 7130 RG with the rubber feet at the bottom on a flat and stable surface.Stand-up mountingSnap the cradle into the holes located on the side of the CellPipe 7130 RG and then place it on a desk so that LEDs are visible.To install the CellPipe 7130 RGSupplies•CellPipe 7130 RG•One RJ-11 telephone cable (only for 6Vz.A2131)•One TAE-F to RJ45 cable (only for 6Ve.B2131)•One RJ-45 category 5 Ethernet cable (yellow)•Power adapterBefore you beginCAUTIONPotential for equipment damage and personal harmBefore installing the CellPipe 7130 RG, ensure you have thoroughly read the Safety precautions and Prerequisites in chapter 1.Turn off all devices (computer, hub, CellPipe 7130 RG) before beginning this procedure.
Hardware installationTo install the CellPipe 7130 RG............................................................................................................................................................................................................................................................3EQ-10280-AAAA-TCZZAEdition 01 February 2011 2-3............................................................................................................................................................................................................................................................Figure 2-1 Cable connections of 6Vz.A2131Figure 2-2 Cable connections of 6Ve.B2131Procedure1. Connect one end of the gray RJ-11 cable (omly for 6Vz.A2131) or gray TAE-RJ45 cable (only for 6Ve.B2131) into the gray DSL port on the CellPipe 7130 RG and the other end to your telephone/VDSL service connection.2. Connect one end of the yellow RJ-45 Ethernet cable to any of the yellow Ethernet LAN ports (1 to 4) on the CellPipe 7130 RG. Connect the other end of the cable to your Ethernet PC (or LAN hub if you are setting up an intranet).3. Turn the power switch on.........................................................................................................................................................END OF STEPSYou might need to configure the Internet properties on your Ethernet PC; see Appendix B, TCP/IP configuration, or the Quick Installation Guide for detailed instructions.After setting up the CellPipe 7130 RG and your PC(s), you can access the web configuration tool; see Accessing the CellPipe 7130 RG web configuration tool.
............................................................................................................................................................................................................................................................RGAM installation of the Residential Gateway ApplicationModuleHardware installation2-4 3EQ-10280-AAAA-TCZZAEdition 01 February 2011............................................................................................................................................................................................................................................................RGAM installation of the Residential Gateway Application ModulePurposeThe CellPipe 7130 Residential Gateway Application Module (RGAM) is an USB devices which adds processing power to the residential gateway. This will allow future home services to be deployed in your home, provided by your service provider. InstallationAs shown in the drawing, the RGAM has a USB 2.0 metal interface. This metal interface should go into the RGAM slot first. The ventilation holes should facing up. Slide the RGAM into the slot until it is blocked. Once inserted, the top of the RGAM will stick outside the enclosure as illustrated below. Once the RGAM is inserted, the RGAM will start up automatically. On the front panel of the residential gateway, the "USB 2" LED will light up, indicating that the RGAM is up and running.
Hardware installationRGAM installation of the Residential Gateway Application Module............................................................................................................................................................................................................................................................3EQ-10280-AAAA-TCZZAEdition 01 February 2011 2-5............................................................................................................................................................................................................................................................Figure 2-3 RGAM installationWARNINGDo not connect the RGAM to devices which are not RGAM-READY. This may damage the RGAM or the device.
............................................................................................................................................................................................................................................................RGAM installation of the Residential Gateway ApplicationModuleHardware installation2-6 3EQ-10280-AAAA-TCZZAEdition 01 February 2011............................................................................................................................................................................................................................................................
3-13EQ-10280-AAAA-TCZZAEdition 01 February 2011............................................................................................................................................................................................................................................................3 Accessing the CellPipe 7130 RG web configuration toolOverviewPurposeThis chapter explains how to access the CellPipe 7130 RG web configuration tool by entering the IP address and the default passwords.The management interface software is HTML-based and can be accessed using a web browser.ContentsThis chapter covers the following topic:To access the CellPipe 7130 RG web configuration toolWhen to useUse this procedure to access the web configuration interface of the CellPipe 7130 RG. The configuration interface enables you to secure the CellPipe 7130 RG, limit access, set traffic routes, modify passwords, and configure advanced settings.Before you beginBefore you can configure the CellPipe 7130 RG, it must be installed, connected to a web-enabled PC, and turned on.To establish the initial connection with the CellPipe 7130 Gateway, your computers should be configured to obtain automatically a network address via DHCP or via statically configuration of the network address. In this case, the IP address should be in the range of 192.168.2.2 up to 192.168.2.99, for instance 192.168.2.10 The netmask should be 255.255.255.0To access the CellPipe 7130 RG web configuration tool 3-1
............................................................................................................................................................................................................................................................To access the CellPipe 7130 RG web configuration toolAccessing the CellPipe 7130 RG web configuration tool3-2 3EQ-10280-AAAA-TCZZAEdition 01 February 2011............................................................................................................................................................................................................................................................Note: If you are not sure how to configure your computer to be a DHCP client or to set your IP address and subnet mask, please refer to Appendix B, TCP/IP configuration, or the Quick Installation Guide for more information.Procedure1. Open a web browser and enter the IP address of the CellPipe 7130 RG in the address bar:http://192.168.2.1 The login window appears; see Figure 3-1.Figure 3-1 Login window2. Enter your username and password and click OK.The default admin username is admin and the default admin password is admin.The Status window appears; see Figure 3-2.
Accessing the CellPipe 7130 RG web configuration toolTo access the CellPipe 7130 RG web configuration tool............................................................................................................................................................................................................................................................3EQ-10280-AAAA-TCZZAEdition 01 February 2011 3-3............................................................................................................................................................................................................................................................Figure 3-2 Status windowThe status window is described in Chapter 4, Status.Note: Once you have logged in for the first time, you should change your login password. See the System Settings section in the Utilities chapter for instructions.3. Click the Logout button to log off; see Figure 3-3.Figure 3-3 Logout button........................................................................................................................................................END OF STEPSConfiguration menusAll configuration and management of the CellPipe 7130 RG is done using the web configuration tool. Click on Status, Network, WiFi Setup, Firewall Setup, Advanced Setup, QoS PTM Setup, QoS ATM Setup, Teleph o n y, or Utilities in the main menu to view the configuration menus or information located in each directory.
............................................................................................................................................................................................................................................................To access the CellPipe 7130 RG web configuration toolAccessing the CellPipe 7130 RG web configuration tool3-4 3EQ-10280-AAAA-TCZZAEdition 01 February 2011............................................................................................................................................................................................................................................................
4-13EQ-10280-AAAA-TCZZAEdition 01 February 2011............................................................................................................................................................................................................................................................4 StatusOverviewPurposeThis chapter describes the contents of the Status menu, which contains the status information for the CellPipe 7130 RG, its connections, and the connected hardware.Click Status in the main menu to open the Status menu.ContentsThis chapter covers the following topics:System UsageThe System Usage window shows the current status of the software, system time, memory, WAN connection, and LAN connection.Select System Usage in the Status menu to access the System Usage window; see Figure 4-1. System Usage 4-1WAN PTM Status 4-3DSL Link Status 4-4Table 4-3 Field descriptions 4-5DHCP Lease 4-7WiFi Association 4-8WAN/(W)LAN Statistics 4-8IGMP Membership 4-10IGMP Statistics 4-10
............................................................................................................................................................................................................................................................System UsageStatus4-2 3EQ-10280-AAAA-TCZZAEdition 01 February 2011............................................................................................................................................................................................................................................................Figure 4-1 System Usage windowTable 4-1 describes the fields of the System Usage window.Table 4-1 Field descriptionsField DescriptionVersion InfoModel Name The model name of the CellPipe 7130 RG.Firmware Version The current version of the firmware.Release Date The release date of the firmware.System UsageSystem Up Time The amount of time the system has been operational.System Loading Average The average loading time of the CPU.Total Memory The memory capacity of the system in Kb.Used Memory The amount of system memory used in Kb.Free Memory The amount of memory available in Kb.Network - WAN StatusWAN MAC The MAC address of the WAN connection.VoIP Account Status1 to 10 Number: The status (Enabled or Disabled) of accounts 1 to 10.Network - LAN StatusLAN IP Address The management IP address of the LAN interface.
StatusWAN PTM Status............................................................................................................................................................................................................................................................3EQ-10280-AAAA-TCZZAEdition 01 February 2011 4-3............................................................................................................................................................................................................................................................WAN PTM StatusThis menu shows the WAN packet transfer Mode (PTM) status and data.Select WAN PTM Status in the Status menu to access the WAN PTM Status window; see Figure 4-2.Figure 4-2 WAN PTM Status windowTable 4-2 describes the fields of the WAN PTM Status window.Table 4-2 Field descriptionsLAN NetMask The subnet mask of the LAN IP address.LAN MAC The MAC address of the LAN interface.DHCP Enable DHCP handling method at LAN device.WLAN MAC The MAC address of the WLAN interface.WLAN SSID The SSID used to identify the CellPipe 7130 RG.Field DescriptionField DescriptionInterface Name The name assigned to this connection.Mode The connection mode: •Static IP•DHCP•PPPoE•BridgeVLAN ID The VLAN ID number from 0 to 4094.IP Address The IP address of the connection.Netmask The subnet mask of the IP address.Gateway The IP address of the gateway.
............................................................................................................................................................................................................................................................DSL Link StatusStatus4-4 3EQ-10280-AAAA-TCZZAEdition 01 February 2011............................................................................................................................................................................................................................................................DSL Link StatusThe DSL Link Status window shows the DSL connection status and data.Select DSL Link Status in the Status menu to access the DSL Link Status window; see Figure 4-3.Figure 4-3 DSL Link Status windowTable 4-3 describes the fields of the DSL Link Status window.DNS 1 to 3 The IP address of the DNS.Field Description
StatusDSL Link Status............................................................................................................................................................................................................................................................3EQ-10280-AAAA-TCZZAEdition 01 February 2011 4-5............................................................................................................................................................................................................................................................Table 4-3 Field descriptionsField DescriptionDSL Firmware Version The version of firmware in use.Mode The modulation protocolTraffic Type The channel typeStatus This is the status of the DSL link.Link Power State Displays the power management state of the DSL connection.Line Coding (Trellis) The Trellis Coding status of downstream and upstream.SNR Margin(0.1dB) This is a signal-to-noise ratio (SNR) margin for traffic going in both directions.Atternuation(0.1dB) An estimate of the average loop attenuation downstream and upstream.Output Power(0.1dBm) The total output power in both directions.Attainable Rate (Kbps): This is the maximum achievable downstream rate.Rate (Kbps) The actual rate at which data is flowing in both directions.MSGc (# of bytes in overhead channel message)Number of bytes in overhead channel messageB (# of bytes in Mux Data Frame) Number of bytes in Mux Data FrameM (# of Mux Data Frames in an RS codeword)Number of Mux Data Frames in FEC Data FrameT (# of Mux Data Frames in a OH sub-frame)Mux Data Frames over sync bytesK (number of bytes in DMT frame) This is the number of data bytes in an DSL data frame.R The number of redundant check bytes per Reed-Solomon code word.S The length of the Reed-Solomon code word, in data frames.L Number of bits in PMD Data FrameD (interleabver depth) The interleaver depth.I (interleaver block size in bytes) Number of bytes in interleaver block sizeN (RS codeword size) The size of RS codeword.Delay (msec) The delay, in microseconds, of the DSL connection.
............................................................................................................................................................................................................................................................Device TableStatus4-6 3EQ-10280-AAAA-TCZZAEdition 01 February 2011............................................................................................................................................................................................................................................................Device TableThe Device Table shows information about the devices that have connected to the CellPipe 7130 RG.Select Device Table in the Status menu to access the Device Table; see Figure 4-4.INP (DMT symbol) INP:Impulse Noise Protection DMT:Discrete Multi-toneOH Frames The number of overhead frames.OH Frame Errors The number of overhead frame errors.Super Frames This is the total number of super frames.Super Frame Errors The number of super frames received that had errors.RS Words This is the total number of Reed-Solomon code words.RS Correctable Errors The number of Reed-Solomon code words with correctable errors.RS Uncorrectable Errors The number of R-S code words that had uncorrectable errors.HEC Errors The total number of header error checksum errors.OCD Errors The number of out-of-cell delineation errors.LCD Errors The total of lost-cell-delineation errors.Total Cells Total number of cells.Data Cells The number of data cells.Bit Errors The number of Bit Error.Total ES Total number of Errored Seconds.Total SES Total number of Severely Errored Seconds.Total UAS Total number of Unavailable Seconds.Field Description
StatusDHCP Lease............................................................................................................................................................................................................................................................3EQ-10280-AAAA-TCZZAEdition 01 February 2011 4-7............................................................................................................................................................................................................................................................Figure 4-4 Device TableTable 4-4 describes the fields of the Device Table window.Table 4-4 Field descriptionsDHCP LeaseThe DHCP Lease window lists the IP addresses leased to the DHCP clients in the LAN environment.Select DHCP Lease in the Status menu to access the DHCP Lease window; see Figure 4-5.Figure 4-5 DHCP Lease windowTable 4-5 describes the fields of the DHCP Lease window.Table 4-5 Field descriptionsField DescriptionHost Name The name of the device connected to the gateway.IP Address The IP address assigned to the device.Attached By Method used to connect to the gateway.MAC Address The MAC address of the attached device.Field DescriptionNo. The index number of the entry in the table.IP Address The IP address leased to the LAN device.MAC Address The MAC address of the LAN device.
............................................................................................................................................................................................................................................................WiFi AssociationStatus4-8 3EQ-10280-AAAA-TCZZAEdition 01 February 2011............................................................................................................................................................................................................................................................WiFi AssociationThe WiFi Association window lists the wireless clients that are currently connected to the CellPipe 7130 RG.Select WiFi Association in the Status menu to access the WiFi Association window; see Figure 4-6.Figure 4-6 WiFi Association windowTable 4-6 describes the fields of the WiFi Association window.Table 4-6 Field descriptionsWAN/(W)LAN StatisticsThe WAN/(W)LAN Statistics window shows the number of bytes that have been received or transmitted by the WAN, LAN, and WLAN interfaces.Select WAN/(W)LAN Statistics in the Status menu to access the WAN/(W)LAN Statistics window; see Figure 4-7.Host Name The host name of the DHCP client.Vendor The platform of the DHCP client.Expiry The time remaining before the lease expires.Field DescriptionField DescriptionNo. The index number of the entry.MAC Address The MAC address of the wireless device connected to the CellPipe 7130 RG.Rate The transmission rate of the wireless device connected to the CellPipe 7130 RG.
StatusWAN/(W)LAN Statistics............................................................................................................................................................................................................................................................3EQ-10280-AAAA-TCZZAEdition 01 February 2011 4-9............................................................................................................................................................................................................................................................Figure 4-7 WAN/(W)LAN Statistics windowTable 4-7 describes the fields of the WAN/(W)LAN Statistics window.Table 4-7 Field descriptionsField DescriptionRx Bytes The number of bytes that have been received.Rx Packets The number of packets that have been received.Rx Packets-Errored The number of packets that have been received with errors.Rx Packets-Dropped The number of packets that have been dropped after being received.Tx Bytes The number of bytes that have been transmitted.Tx Packets The number of packets that have been transmitted.
............................................................................................................................................................................................................................................................IGMP MembershipStatus4-10 3EQ-10280-AAAA-TCZZAEdition 01 February 2011............................................................................................................................................................................................................................................................IGMP MembershipThe IGMP Membership window shows the IGMP members.Select IGMP Membership in the Status menu to access the IGMP Membership window; see Figure 4-8.Figure 4-8 IGMP Membership windowTable 4-8 describes the fields of the IGMP Membership window.Table 4-8 Field descriptionsIGMP StatisticsThe IGMP Statistics window shows the IGMP statistics.Note: This window only shows the IGMP activity statistics for each group within the time period you have set.Select IGMP Statistics in the Status menu to access the IGMP Statistics windows; see Figure 4-9.Tx Packets-Errored The number of packets that have been transmitted with errors.Tx Packets-Dropped The number of packets that have been dropped after being transmitted.Tx Packets-Collided The number of packets that collided when transmitted.Field DescriptionField DescriptionMulticast IP Group The multicast group.Client Lists the IP address of the client in the specific multicast group.
Status............................................................................................................................................................................................................................................................3EQ-10280-AAAA-TCZZAEdition 01 February 2011 4-11............................................................................................................................................................................................................................................................Figure 4-9 IGMP Statistics windowTable 4-9 describes the fields of the IGMP Statistics window.Table 4-9 Field descriptionsField DescriptionPeriod Select a time period in minutes to collect and display the IGMP statistics.Apply Click to show the IGMP group information for the selected time period.Join Number of clients in the IGMP group domain.Leave Number of clients that have left the IGMP group domain.
............................................................................................................................................................................................................................................................Status4-12 3EQ-10280-AAAA-TCZZAEdition 01 February 2011............................................................................................................................................................................................................................................................
5-13EQ-10280-AAAA-TCZZAEdition 01 February 2011............................................................................................................................................................................................................................................................5NetworkOverviewPurposeThis chapter explains how to configure the network settings for the CellPipe 7130 RG.Click the Network in the main menu to open the Network menu.ContentsThis chapter covers the following topics:USBThe USB windows allows you to configure services using the USB 2.0 interface. On the USB 2.0 interface, the following devices can be connected: Printer, storage device, sensor network interface.By enabling the printerserver service "USB printer", you can print via your home network to this printer. By connecting a storage devices, the gateway can be used as fileserver. When enabling the DMS service, all digital media on the storage device will become available on your home network. (UPnP AV)Select USB in the Network menu to access the USB&DMS window; see Figure 5-1.USB 5-1LAN Settings 5-3WAN Link Selection 5-6WAN PTM Connections 5-6
............................................................................................................................................................................................................................................................USBNetwork5-2 3EQ-10280-AAAA-TCZZAEdition 01 February 2011............................................................................................................................................................................................................................................................Figure 5-1 USB&DMS windowTable 5-1 describes the fields of the USB&DMS window.Table 5-1 Field descriptionsConnecting storage deviceWhen a storage device is connected, this storage can be accessed via the LAN (Home network) and can not be accessed from the WAN side due to security reasons. The following file-systems are supported : FAT16, FAT32, NTFS, EXT2, EXT3. No access rights can be set, neither user accounts. For windows, the filesharing can be access by opening the internet explorer and typing the IP address of the gateway. The default IP address is \\192.168.2.1\ The default userid and password are used : guest / guestField DescriptionUSB Enable Select Enable to enable USB.Select Disable to disable USB.USB Printer Name Enter a USB printer name.DMS Enable Select Enable to enable DMS.Select Disable to disable DMS.DMS Server Name Enter a DMS Server name.Apply Changes Click to save your changes.
NetworkLAN Settings............................................................................................................................................................................................................................................................3EQ-10280-AAAA-TCZZAEdition 01 February 2011 5-3............................................................................................................................................................................................................................................................Figure 5-2 Connecting storage deviceNote:•DMS works only for devices which are directly connected to the LAN interface of the gateway.•The content cannot be reached from the WAN interface.•DMS only works when an storage devices is connected to the USB 2.0 interface.•The DMS will support UMLAUT characters•The following file systems will be supported: FAT16, FAT32, NTFS, EXT2, EXT3 via USBWARNINGWhen a storage (USB-harddisk or USB memory stick) is connected to the gateway, the content will be automatically be available on your home network and accessible by everybody on that home network.If the DMS function is enabled, the gateway discovers all digital media on the connected storage device (Harddisk/USB-memory-stick) and make this accessible via PnP AV protocol.LAN SettingsThe LAN Settings window enables you to configure the IP address, subnet mask, DHCP settings, DHCP relay, and static IP lease.
............................................................................................................................................................................................................................................................LAN SettingsNetwork5-4 3EQ-10280-AAAA-TCZZAEdition 01 February 2011............................................................................................................................................................................................................................................................Select LAN Settings in the Network menu to access the LAN Settings window; see Figure 5-3.Figure 5-3 LAN Settings window - DHCP Server option selectedTable 5-2 describes the fields of the LAN Settings window.
NetworkLAN Settings............................................................................................................................................................................................................................................................3EQ-10280-AAAA-TCZZAEdition 01 February 2011 5-5............................................................................................................................................................................................................................................................Table 5-2 Field descriptionsField DescriptionIP Address The IP address of the LAN interface in dotted decimal notation. The default is 192.168.2.1. You can change this address as necessary to any address that is reserved for private use.Subnet Mask The subnet mask of the IP addresses in your LAN; for example, 255.255.255.0.DHCP Server Select DHCP Server to enable DHCP server. The CellPipe 7130 RG automatically assigns the IP addresses, default gateway, and DNS servers to computers that support the DHCP client; for example, Windows 95 or Windows NT.Select DHCP Relay to enable DHCP Relay.Select Disable to disable DHCP server.Note: Figure 5-2 shows the DHCP Server options. Selecting DHCP Relay will open the DHCP Relay server options.DHCP Relay Server 1 Enter the IP address of the DHCP server.(DHCP Relay)DHCP Relay Server 2 Enter the IP address of the second DHCP server for a different service, if applicable.(DHCP Relay)Mapping Vendor ID Enter the Vendor ID for DHCP Option 60. When the client sends a DHCP request that contains vendor ID is equal to the Vendor ID, the request will be sent to "DHCP Relay Server 2". (DHCP Relay)DHCP Starting IP AddressDHCP Ending IP AddressThe range of IP addresses that will be assigned to the DHCP client.DHCP Lease Time The time period during which the computers retain the IP addresses assigned to them.Static Lease Assign a static IP address to DHCP clients based on their MAC address.Block Lease The MAC address of the client to block from acquiring an IP address.Apply Changes Click to save your changes.
............................................................................................................................................................................................................................................................WAN Link SelectionNetwork5-6 3EQ-10280-AAAA-TCZZAEdition 01 February 2011............................................................................................................................................................................................................................................................WAN Link SelectionThe WAN Link Selection window specifies which link will be used for the WAN connection, one of auto-dedicate mode, Gigabit Ethernet, or DSL.Note: You must reboot the CellPipe 7130 RG to switch from one WAN interface to another.Select WAN Link Selection in the Network menu to access the WAN Link Selection window; see Figure 5-4.Figure 5-4 WAN Link Selection windowTable 5-3 describes the fields of the WAN Link Selection window.Table 5-3 Field descriptionsWAN PTM ConnectionsWAN PTM connections are the connections used when the device operates in DSL-PTM mode (if you are uncertain whether your DSL service is PTM, contact your ISP). The WAN PTM Connections window enables you to configure multiple connections.Field DescriptionAuto Select to automatically detect the WAN link.Note: Only one of the two LAN ports should be physically connected.Gigabit Ethernet Select to use only the Gigabit Ethernet port as the WAN link.VDSL Select to use the VDSL port.Apply Changes Click to save your changes.
NetworkWAN PTM Connections............................................................................................................................................................................................................................................................3EQ-10280-AAAA-TCZZAEdition 01 February 2011 5-7............................................................................................................................................................................................................................................................CAUTIONIt is recommended that the WAN PTM connections be changed by trained service personnel. Improper configuration can lead to loss of connectivity to the residential gateway from the LAN side as well as the WAN side.There are three different binding methods for the connections: •Port based binding•MAC based binding•No LAN/WLAN bindingThe four following types of connections can be used:•Static IP•DHCP Mode•PPPoE Mode•Bridge ModeSelect WAN PTM Connections in the Network menu to access the WAN PTM Connections window; see Figure 5-5.
............................................................................................................................................................................................................................................................WAN PT M ConnectionsNetwork5-8 3EQ-10280-AAAA-TCZZAEdition 01 February 2011............................................................................................................................................................................................................................................................Figure 5-5 WAN PTM Connections windowTable 5-4 describes the fields of the WAN PTM Connections window.Table 5-4 Field descriptionsField DescriptionInterface Name Enter a name for your new connection.Mode Select a mode for the connection type: •Static IP•DHCP•PPPoE•Bridge
NetworkWAN PTM Connections............................................................................................................................................................................................................................................................3EQ-10280-AAAA-TCZZAEdition 01 February 2011 5-9............................................................................................................................................................................................................................................................Binding Select a binding method:•Port Based to bind traffic to the connection by LAN or WLAN port.•MAC Based to bind traffic to the connection by MAC address.•No LAN/WLAN Binding so that the connection does not bind traffic to any port or MAC.Note: You cannot use a combination of Port based and MAC based binding. Note: When using MAC based binding, you must define a Default connection first. This default connection can be a routed or bridged connection. After defining the default MAC based connection, you can add extra bridged (not routed) connections which are selected on basis of configurable MAC layer based criteria.Local Service Enable a local service:•Enable VoIP to provide VoIP service.•Enable CWMP to provide remote control service. It allows a remote server to manage the gateway•Enable IGMP Proxy to provide service to be used for video streaming and gaming.•Enable Default Route to set the connection as the gateway of last resort.Add Click to add the new connection and proceed to the next configuration window.Note: After adding new connections, click Activate WAN Settings to activate the connection. This button will be only visible if you added a new connection or made changes to the settings.Interface Name (read-only) The name of the interface.Mode (read-only) The selected mode.VLAN ID (read-only) The VLAN ID.Default Route All connections will be routed via the default route, except for the connection that has special routing. There can be only one default route between all the connections.IGMP Proxy Select the interface to support IGMP service.VoIP Select the interface to support VoIP service.CWMP Select the interface to support CWMP service.Field Description
............................................................................................................................................................................................................................................................WAN PT M ConnectionsNetwork5-10 3EQ-10280-AAAA-TCZZAEdition 01 February 2011............................................................................................................................................................................................................................................................Port based bindingPort based mode enables you to bind ports to your WAN connection. You can bind LAN ports 1 to 4 and WLAN SSID 1 to 4 in the WAN mode you selected. The default WLAN SSID number is 1 and you can configure 2 to 4 in the WiFi Settings.You can select the Port Based radio button for each WAN mode and then click Add to proceed to the next configuration window.In Port based mode, you can add up to four connections in routed mode.Note: If you do not set a VLAN ID in the connections, you can only have one connection in Static IP or DHCP mode and three connections maximum in PPPoE.Note: If you already have a connection with Port based binding, you can not select MAC based binding for any other connections.The following WAN modes support port-based binding: •Static IP•DHCP•PPPoE•BridgeStatic IPIf you select Static IP as the mode in the WAN PTM Connections, the Static IP settings window with Port based binding opens; see Figure 5-6.Binding (read-only) Shows which ports or MAC addresses are bound on the connection.Delete All Click to delete all the connections.Edit Click to modify the settings of the connection.After changing the connection settings, press Activate WAN Settings to activate the connection. This button will be only visible if you made changes to the settings or added a new connection.Delete Click to delete the connection.Field Description
NetworkWAN PTM Connections............................................................................................................................................................................................................................................................3EQ-10280-AAAA-TCZZAEdition 01 February 2011 5-11............................................................................................................................................................................................................................................................Figure 5-6 Static IP settings window with Port based bindingTable 5-5 describes the fields of Static IP settings window with Port based binding.Table 5-5 Field descriptionsField DescriptionLAN BindingLAN Binding Select the port to which you want to bind the connection.WLAN Binding Select the SSID to which you want to bind the connection.WANVLAN Select Untagged if VLAN tagging is not to be used for this WAN connection.Select Always use ID if VLAN tagging is to be used and enter the VLAN ID number (between 0 and 4094).802.1X Select Enable to use 802.1x or select Disable to turn off 802.1x.IP Address Enter the IP address provided by your ISP.NetMask Enter the subnet mask provided by your ISP.Gateway Enter the gateway IP address provided by your ISP.DNS1 to 3 Enter the DNS IP address (these are optional).
............................................................................................................................................................................................................................................................WAN PT M ConnectionsNetwork5-12 3EQ-10280-AAAA-TCZZAEdition 01 February 2011............................................................................................................................................................................................................................................................DHCPIf you select DHCP as the mode in the WAN PTM Connections window, the DHCP settings window with Port based binding opens; see Figure 5-7.Figure 5-7 DHCP settings window with Port based bindingTable 5-6 describes the fields of DHCP settings window with Port based binding.Table 5-6 Field descriptionsMTU(Bytes) Select Auto to set the MTU to the default (1500) or select Manual and enter a value in bytes.Next Click to go to the QoS Defaults window.Back Click to return to the previous window.Activate WAN Setting Click to activate the connection.Delete All Click to remove all WAN connections.Edit Click to make changes to a specific connection.Delete Click to remove a specific connection.Field DescriptionLAN BindingLAN Binding Select the port to which you want to bind the connection.Field Description
NetworkWAN PTM Connections............................................................................................................................................................................................................................................................3EQ-10280-AAAA-TCZZAEdition 01 February 2011 5-13............................................................................................................................................................................................................................................................PPPoEIf you select PPPoE as the mode in the WAN PTM Connections window, the PPPoE settings window with Port based binding opens; see Figure 5-8.WLAN Binding Select the SSID to which you want to bind the connection.WANVLAN Select Untagged if VLAN tagging is not to be used for this WAN connection.Select Always use ID if VLAN tagging is to be used and enter the VLAN ID number (between 0 and 4094).802.1X Select Enable to use 802.1x or select Disable to turn off 802.1x.Host Name Enter the host name provided by your ISP. If you are unsure of the host name, please consult with your ISP for more information.Domain Name Enter the domain name provided by your ISP. If you are unsure of the domain name, please consult with your ISP for more information.Vender Class ID If required, set the vender class ID to obtain its lease from the DHCP server. Please consult with your ISP for more information.Client ID If required, set the client ID to obtain its lease from the DHCP server. Please consult with your ISP for more information.MTU(Bytes) Select Auto to set the MTU to the default (1500) or select Manual and enter a value in bytes.Activate WAN Setting Click to activate the connection.Delete All Click to remove all WAN connections.Edit Click to make changes to a specific connection.Delete Click to remove a specific connection.Next Click to go to the QoS Defaults window.Back Click to return to the previous window.Field Description
............................................................................................................................................................................................................................................................WAN PT M ConnectionsNetwork5-14 3EQ-10280-AAAA-TCZZAEdition 01 February 2011............................................................................................................................................................................................................................................................Figure 5-8 PPPoE settings window with Port based bindingTable 5-7 describes the fields of PPPoE settings window with Port based binding.Table 5-7 Field descriptionsFields DescriptionLAN BindingLAN Binding Select the port to which you want to bind the connection.WLAN Binding Select the SSID to which you want to bind the connection.WANVLAN Select Untagged if VLAN tagging is not to be used for this WAN connection.Select Always use ID if VLAN tagging is to be used and enter the VLAN ID number (between 0 and 4094).User Name Enter the username for the PPPoE connection. Please consult with your ISP for more information.Password Enter the password for the PPPoE connection. Please consult with your ISP for more information.Access Concentrator The access concentrator is optional. Please consult with your ISP for information.
NetworkWAN PTM Connections............................................................................................................................................................................................................................................................3EQ-10280-AAAA-TCZZAEdition 01 February 2011 5-15............................................................................................................................................................................................................................................................BridgeIf you select Bridge as the mode in the WAN PTM Connections window, the Bridge settings window with Port based binding opens; see Figure 5-9.Service Name The service name is optional. Please consult with your ISP for information.Mode Select the mode:•Select Connect on demand to allow the gateway to connect to the Internet only when you are trying to access it. Enter a Max idle time. If there are no activities in the specified time period, the CellPipe 7130 RG will disconnect the connection.•Select Always on to set the CellPipe 7130 RG to always connect to the Internet.•Select Manual and then click Connect to manually connect the CellPipe 7130 RG to the Internet. Click Disconnect to disconnect the connection.Authentication Method Select the authentication mode:•CHAP + PAP•Only MS-CHAP•Only CHAP•Only PAPThis is optional. Please consult with your ISP for more information.MTU (Bytes) Select Auto to set the MTU to the default (1492) or select Manual and enter a value in bytes.Activate WAN Setting Click to activate the connection.Delete All Click to remove all WAN connections.Edit Click to make changes to a specific connection.Delete Click to remove aspecific connectionNext Click to go to the QoS Defaults window.Back Click to return to the previous window.Fields Description
............................................................................................................................................................................................................................................................WAN PT M ConnectionsNetwork5-16 3EQ-10280-AAAA-TCZZAEdition 01 February 2011............................................................................................................................................................................................................................................................Figure 5-9 Bridge settings window with Port based bindingTable 5-8 describes the fields of Bridge settings window with Port based binding.Table 5-8 Field descriptionsFields DescriptionLAN BindingLAN Binding Select the port to which you want to bind the connection.WLAN Binding Select the SSID to which you want to bind the connection.WANVLAN Select Untagged if VLAN tagging is not to be used for this WAN connection.Select Always use ID if VLAN tagging is to be used and enter the VLAN ID number (between 0 and 4094).QoS Queue Enter the QoS queue number.CoS Remarking Enter the CoS remarking number.IP Address Enter the IP address provided by your ISP.NetMask Enter the subnet mask provided by your ISP.Save Click to save your changes.Back Click to return to the previous window.Activate WAN Setting Click to activate the connection.
NetworkWAN PTM Connections............................................................................................................................................................................................................................................................3EQ-10280-AAAA-TCZZAEdition 01 February 2011 5-17............................................................................................................................................................................................................................................................MAC based bindingMAC based mode enables you to bind your connection by DHCP Option 60, Ethernet type, source MAC, or destination MAC.Before you begin, you must configure a default connection. It should be routed or bridge mode. Afterwards you can configure MAC based binding (the other binding options are Port based and No LAN/WLAN) by DHCP Option 60, Ethernet type, source MAC, or destination MAC.You can select the MAC Based radio button for each WAN mode and then click Add to enter the next configuration window.You can set a maximum of 20 connections in MAC based binding.Note: If you already have a connection with MAC based binding, you cannot select Port based binding for any other connections.The following section shows the creation of a default DHCP connection with MAC based binding.DHCPIf you select DHCP as the mode, the DHCP settings window with MAC based binding opens; see Figure 5-10.Delete All Click to remove all WAN connections.Edit Click to make changes to a specific connection.Delete Click to remove aspecific connectionFields Description
............................................................................................................................................................................................................................................................WAN PT M ConnectionsNetwork5-18 3EQ-10280-AAAA-TCZZAEdition 01 February 2011............................................................................................................................................................................................................................................................Figure 5-10 DHCP settings window with MAC based bindingTable 5-9 describes the fields of DHCP settings window with MAC based binding.Table 5-9 Field descriptionsFields DescriptionLAN BindingDefault The first rule must be the default. After you have a default rule you can choose the other options. For example, you can select DHCP Option 60, Ethernet Type, Source MAC, or Destination MAC.DHCP Option 60 Select the radio button and enter the applicable alphanumeric identification (wildcard * is also applicable).Ethernet Type Select the radio button and enter the applicable Ethernet Type code (4 hex digits).Source MAC Select the radio button and enter the applicable Source MAC address in hexadecimal format.Destination MAC Select the radio button and enter the applicable Destination MAC address in hexadecimal format.
NetworkWAN PTM Connections............................................................................................................................................................................................................................................................3EQ-10280-AAAA-TCZZAEdition 01 February 2011 5-19............................................................................................................................................................................................................................................................Now that you have a default connection, the WAN PTM Connections window with MAC based binding opens; see Figure 5-11.WANVLAN Select Untagged if VLAN tagging is not to be used for this WAN connection.Select Always use ID if VLAN tagging is to be used and enter the VLAN ID number (between 0 and 4094).802.1x Select Enable to use 802.1x or select Disable to turn off 802.1x. Please consult your ISP for more information.Host Name Enter the host name provided by your ISP. Please consult with your ISP for more information.Domain Name Enter the domain name provided by your ISP. Please consult with your ISP for more information.Vender Class ID If you are required, set the vender class ID to obtain its lease from the DHCP server. Please consult with your ISP for more information.Client ID If you are required, set the client ID to obtain its lease from the DHCP server. Please consult with your ISP for more information.MTU(Bytes) Select Auto to set the MTU to the default (1500) or select Manual and enter a value in bytes.Next Click to go to the QoS Defaults window.Back Click to return to the previous page.Fields Description
............................................................................................................................................................................................................................................................WAN PT M ConnectionsNetwork5-20 3EQ-10280-AAAA-TCZZAEdition 01 February 2011............................................................................................................................................................................................................................................................Figure 5-11 WAN PTM Connections window with MAC based bindingAfter you have a default connection, you can choose the WAN Mode you want and click Add to add a new connection. You can only choose Bridge mode with MAC based binding. Click Add to set the configurations.When you select Bridge mode with MAC based binding and click Add, the Bridge settings window with MAC based binding opens; see Figure 5-12.
NetworkWAN PTM Connections............................................................................................................................................................................................................................................................3EQ-10280-AAAA-TCZZAEdition 01 February 2011 5-21............................................................................................................................................................................................................................................................Figure 5-12 Bridge settings window with MAC based bindingTable 5-10 describes the fields of Bridge settings window with MAC based binding.Table 5-10 Field descriptionsFields DescriptionLAN BindingDefault The first rule must be the default. After you have a default rule you can choose the other options. For example, you can select DHCP Option 60, Ethernet Type, Source MAC, or Destination MAC.DHCP Option 60 Select the radio button and enter the applicable alphanumeric identification (wildcard * is also applicable).Ethernet Type Select the radio button and enter the applicable Ethernet Type code (4 hex digits).Source MAC Select the radio button and enter the applicable Source MAC address in hexadecimal format.Destination MAC Select the radio button and enter the applicable Destination MAC address in hexadecimal format.
............................................................................................................................................................................................................................................................WAN PT M ConnectionsNetwork5-22 3EQ-10280-AAAA-TCZZAEdition 01 February 2011............................................................................................................................................................................................................................................................After the second connection is set, you are returned to the WAN PTM Connections window; see Figure 5-13. The two new connections, default and bridged, appear in the Overview table.Figure 5-13 WAN PTM Connections window with MAC based bindingYou can only choose Bridge mode with MAC based binding and you can select Static IP, DHCP, or PPPoE with No LAN/WLAN Binding for CWMP and VoIP.WANVLAN Select Untagged if VLAN tagging is not to be used for this WAN connection.Select Always use ID if VLAN tagging is to be used and enter the VLAN ID number (between 0 and 4094).CoS Remarking Enter the CoS remarking number.IP Address Enter the IP address provided by your ISP.NetMask Enter the subnet mask provided by your ISP.Next Click to proceed to the next step.Back Click to return to the previous page.Fields Description
NetworkWAN PTM Connections............................................................................................................................................................................................................................................................3EQ-10280-AAAA-TCZZAEdition 01 February 2011 5-23............................................................................................................................................................................................................................................................No LAN/WLAN bindingNo LAN/WLAN binding enables you to configure your connection with local service CWMP and VoIP. In order to avoid other connections using CWMP and VoIP, No LAN/WLAN Binding is specifically for CWMP and VoIP to build an independent connection.Select the No LAN/WLAN Binding radio button for the binding method and then click Add to enter the next configuration page.Static IPIf you select Static IP as the mode and click Add, the Static IP window with No LAN/WLAN Binding opens; see Figure 5-14.Figure 5-14 Static IP window with No LAN/WLAN BindingTable 5-11 describes the fields of Static IP window with No LAN/WLAN Binding.Table 5-11 Field descriptionsField DescriptionWANVLAN Select Untagged if VLAN tagging is not to be used for this WAN connection.Select Always use ID if VLAN tagging is to be used and enter the VLAN ID number (between 0 to 4094).
............................................................................................................................................................................................................................................................WAN PT M ConnectionsNetwork5-24 3EQ-10280-AAAA-TCZZAEdition 01 February 2011............................................................................................................................................................................................................................................................Figure 5-15 WAN PTM Connections window with Static IP No LAN/WAN CWMP connection created802.1x Select Enable to use 802.1x or select Disable to turn off 802.1x. Please consult your ISP for more information.IP Address Enter the IP address provided by your ISP.NetMask Enter the subnet mask provided by your ISP.Gateway Enter the gateway IP address provided by your ISP.DNS1 to 3 Enter the DNS IP address (these are optional).MTU(Bytes) Select Auto to set the MTU to the default (1500) or select Manual and enter a value in bytes.Next Click to proceed to the QoS Defaults window.Back Click to return to the previous window.Field Description
NetworkWAN PTM Connections............................................................................................................................................................................................................................................................3EQ-10280-AAAA-TCZZAEdition 01 February 2011 5-25............................................................................................................................................................................................................................................................Table 5-12 Field descriptionsDHCPIf you select DHCP as the mode and click Add, the DHCP window with No LAN/WLAN Binding opens; see Figure 5-16.Figure 5-16 DHCP window with No LAN/WLAN BindingTable 5-13 describes the fields of DHCP window with No LAN/WLAN Binding.Table 5-13 Field descriptionsField DescriptionActivate WAN Settings Click to activate the connection.Delete All Click to delete all the connections.Edit Click to modify the settings of the connection.After changing the connection settings, press Activate WAN Settings to activate the connection. This button will be only visible if you made changes to the settings or added a new connection.Delete Click to delete the connection.Field DescriptionVLAN Select Untagged if VLAN tagging is not to be used for this WAN connection.Select Always use ID if VLAN tagging is to be used and enter the VLAN ID number (between 0 and 4094).
............................................................................................................................................................................................................................................................WAN PT M ConnectionsNetwork5-26 3EQ-10280-AAAA-TCZZAEdition 01 February 2011............................................................................................................................................................................................................................................................PPPoEIf you select PPPoE as the mode and click Add, the PPPoE window with No LAN/WLAN Binding opens; see Figure 5-17.802.1x Select Enable to use 802.1x or select Disable to turn off 802.1x. Please consult your ISP for more information.Host Name Enter the host name provided by your ISP. Please consult with your ISP for more information.Domain Name Enter the domain name provided by your ISP. Please consult with your ISP for more information.Vender Class ID If you are required, set the vender class ID to obtain its lease from the DHCP server. Please consult with your ISP for more information.Client ID If you are required, set the client ID to obtain its lease from the DHCP server. Please consult with your ISP for more information.MTU(Bytes) Select Auto to set the MTU to the default (1500) or select Manual and enter a value in bytes.Next Click to go to the QoS Defaults window.Back Click to return to the previous window.Field Description
NetworkWAN PTM Connections............................................................................................................................................................................................................................................................3EQ-10280-AAAA-TCZZAEdition 01 February 2011 5-27............................................................................................................................................................................................................................................................Figure 5-17 PPPoE window with No LAN/WLAN BindingTable 5-14 describes the fields of PPPoE window with No LAN/WLAN Binding.Table 5-14 Field descriptionsField DescriptionVLAN Select Untagged if VLAN tagging is not to be used for this WAN connection.Select Always use ID if VLAN tagging is to be used and enter the VLAN ID number (between 0 to 4094).User Name Enter the username for the PPPoE connection. Please consult with your ISP for more information.Password Enter the password for the PPPoE connection. Please consult with your ISP for more information.Access Concentrator The access concentrator is optional. Please consult with your ISP for more information.Service Name The service name is optional. Please consult with your ISP for more information.
............................................................................................................................................................................................................................................................WAN PT M ConnectionsNetwork5-28 3EQ-10280-AAAA-TCZZAEdition 01 February 2011............................................................................................................................................................................................................................................................QoS DefaultsThe QoS Defaults window enables you to configure the default QoS policy for each WAN connection, see Figure 5-18.Mode Select the mode:•Select Connect on demand to allow the gateway to connect to the Internet only when you are trying to access it. Enter a Max idle time. If there are no activities in the specified time period, the CellPipe 7130 RG will disconnect the connection.•Select Always on to set the CellPipe 7130 RG to always connect to the Internet.•Select Manual and then click Connect to manually connect the CellPipe 7130 RG to the Internet. Click Disconnect to disconnect the connection.Authentication Method Select the authentication mode:•CHAP + PAP•Only MS-CHAP•Only CHAP•Only PAPThis is optional. Please consult with your ISP for more information.MTU (Bytes) Select Auto to set the MTU to the default (1492) or select Manual and enter a value in bytes.Next Click to go to the QoS Defaults window.Back Click to return to the previous window.Field Description
NetworkWAN PTM Connections............................................................................................................................................................................................................................................................3EQ-10280-AAAA-TCZZAEdition 01 February 2011 5-29............................................................................................................................................................................................................................................................Figure 5-18 QoS Defaults window
............................................................................................................................................................................................................................................................WAN PT M ConnectionsNetwork5-30 3EQ-10280-AAAA-TCZZAEdition 01 February 2011............................................................................................................................................................................................................................................................Table 5-15 describes the fields of the QoS Defaults window.Table 5-15 Field descriptionsField DescriptionQoS ClassificationQueueOriginal ToS Tag (First 3 bits of DSCP)Select Original ToS Tag to assign the queue according to the ToS value of the packet.Specified Queue Select Specified Queue and enter a queue number (0 to 7) to which the network traffic will be assigned.Note: When Specified Queue is chosen, you cannot choose Align CoS with ToS Value.ToS/DSCP RemarkingKeep Original ToS Select Keep Original ToS to retain the original ToS value.New ToS Value Select New Tos Value and enter a queue number (0 to 7) to assign to the network traffic.New DSCP Value Select New DSCP Value and enter a DSCP value (0 to 63).CoS (p-bit) RemarkingKeep CoS Value Select Keep CoS Value to retain the original CoS value.New CoS Value Select New CoS Value to assign CoS for network traffic.Align CoS with ToS Value Select to align CoS with ToS value.Note: This field can only be set if you keep Original To S Ta g in queue setting.QoS LAN ClassificationQueueOriginal ToS Tag (First 3 bits of DSCP)Select Original ToS Tag to assign the queue according to the ToS value of the packet.Specified Queue Select Specified Queue and enter a queue number (0 to 7) to which the network traffic will be assigned.Note: When Specified Queue is chosen, you cannot choose Align CoS with ToS Value.ToS/DSCP RemarkingKeep Original ToS Select Keep Original ToS to retain the original ToS value.
Network............................................................................................................................................................................................................................................................3EQ-10280-AAAA-TCZZAEdition 01 February 2011 5-31............................................................................................................................................................................................................................................................New ToS Value Select New Tos Value and enter a queue number (0 to 7) to assign to the network traffic.New DSCP Value Select New DSCP Value and enter a DSCP value (0 to 63).Save Click to save your changes.Back Click to return to the previous window.Field Description
............................................................................................................................................................................................................................................................Network5-32 3EQ-10280-AAAA-TCZZAEdition 01 February 2011............................................................................................................................................................................................................................................................
6-13EQ-10280-AAAA-TCZZAEdition 01 February 2011............................................................................................................................................................................................................................................................6 WiFi setupOverviewPurposeThis chapter explains how to configure the WiFi settings for the CellPipe 7130 RG.Click WiFi Setup in the main menu to open the WiFi Setup menu.ContentsThis chapter covers the following topics:WiFi SettingsThe WiFi Settings window enables you to configure the common wireless settings.Click on WiFi Settings in the WiFi Setup menu to access the WiFi Settings window; see Figure 6-1.WiFi Settings 6-1WiFi Security 6-4WiFi Access Filter 6-6
............................................................................................................................................................................................................................................................WiFi SettingsWiFi setup6-2 3EQ-10280-AAAA-TCZZAEdition 01 February 2011............................................................................................................................................................................................................................................................Figure 6-1 WiFi Settings windowTable 6-1 describes the fields of the WiFi Settings window.Table 6-1 Field descriptionsField DescriptionCommonWiFi Select Enable to turn on wireless and configure the wireless settings. Select Disable to turn off wireless.
WiFi setupWiFi Settings............................................................................................................................................................................................................................................................3EQ-10280-AAAA-TCZZAEdition 01 February 2011 6-3............................................................................................................................................................................................................................................................Multiple SSID Select the number of SSIDs: •1•2•4Tx Power Enter a value between 1 and 100 to control the transmitting signal strength.Radio Mode Select the wireless mode: •802.11b/g•802.11g/n•802.11b/g/n•802.11b•802.11g•802.11nAuto Channel Select Select On to let the wireless access point automatically select a channel with the least interference. Select Off to configure manually. Select Now to set the channel automatically one time.Channel If Auto Channel Select is off, you can manually select a channel for the wireless access point. The default is 1.Beacon Period Enter a beacon period in milliseconds to determine the frequency of the beacon to keep the network synchronized. This is optional.DTIM Period Enter a value to set the delivery traffic indication message. The DTIM field is a countdown field informing clients of the next window for listening to broadcast and multicast messages.Bandwidth Select to enable channel bonding (20/40Mhz) or disable channel bonding . If channel bonding is selected, please also select which extension channel is been used. Note: Not all wireless clients support this.Extension Channel An extension channel is a secondary channel used to bond with the primary channel to increase the performance.Field Description
............................................................................................................................................................................................................................................................WiFi SecurityWiFi setup6-4 3EQ-10280-AAAA-TCZZAEdition 01 February 2011............................................................................................................................................................................................................................................................WiFi SecurityWiFi security enables you to configure the WEP, WPA, or WPA2 security settings. Select WiFi Security in the WiFi Setup menu to access the WiFi Security window; see Figure 6-2.SSID 1 to 4SSID Enter an SSID name (maximum of 32 characters). The SSID is an alphanumeric name shared by all the devices on the wireless network. It must be unique.Broadcast SSID Select On to broadcast the SSID or select Off to hide the SSID.TxRate Select Auto to automatically determine the transmission rate or manually select a transmission rate (maximum 54Mb/s).IGMP Enable Enable to use IGMP or disable to turn off IGMP.WDS Select Enable to use WDS or select Disable to turn off WDS.Note: If you enable WDS, ensure that all other WDS APs are enabled, configured with the same channel, SSID, and encryption keys, and that each AP has a different LAN port IP address.Other WDS Station Enter the wireless MAC addresses of other wireless APs or routers that are in the same WDS.Apply Changes Click to save your changes.Field Description
WiFi setupWiFi Security............................................................................................................................................................................................................................................................3EQ-10280-AAAA-TCZZAEdition 01 February 2011 6-5............................................................................................................................................................................................................................................................Figure 6-2 WiFi Security windowTable 6-2 describes the fields of the WiFi Security window.Table 6-2 Field descriptionsField DescriptionWPS Enable Push Button Control (the WPS push button is located on the front of the CellPipe 7130 RG) or enable PIN and enter your PIN number and click Start. The PIN number is located in the WiFi utility of your computer.Authentication Select one of the following encryption methods for the wireless network:•Open•Shared•WPAPSK•WPA2PSK•WPAPSK/WPA2PSK Mixed•WPA•WPA2
............................................................................................................................................................................................................................................................WiFi Access FilterWiFi setup6-6 3EQ-10280-AAAA-TCZZAEdition 01 February 2011............................................................................................................................................................................................................................................................WiFi Access FilterThe WiFi Access Filter window enables you to block or permit access for wireless clients by MAC address.Select WiFi Access Filter in the WiFi Setup menu to access the WiFi Access Filter window; see Figure 6-3.Security Type Select one of the following for the security type:•NONE•WEP•TKIP•AES•TKIP/AES MixedWEPPassphrase Key Select a level of encryption (64 bits or 128 bits) and enter a passphrase key consisting of 8 to 63 alphanumeric characters and then click Generate.Key1 to 4 Select Key1 to Key4 and enter a WEP key in the respective field. The WEP key must:•contain letters from A to F and numbers from 0 to 9 •contain 10 characters for 64 bit and 26 characters for 128 bit encryptionWPAPSK/WPA2PSKPreshared Key Enter a preshared key consisting of 8 to 63 alphanumeric characters.802.1xRadius Server Enter the IP address of the RADIUS server.Radius Port Enter the port number of the RADIUS server.Radius Key Enter the key of the RADIUS server.Apply Changes Click to save your changes.Field Description
WiFi setupWiFi Access Filter............................................................................................................................................................................................................................................................3EQ-10280-AAAA-TCZZAEdition 01 February 2011 6-7............................................................................................................................................................................................................................................................Figure 6-3 WiFi Access Filter windowTable 6-3 describes the fields of the WiFi Access Filter window.Table 6-3 Field descriptionsField DescriptionAccess Policy Select an access policy:•Disable Filter to turn off WiFi filtering.•Allow to permit access from the specified MAC address.•Deny to deny access from the specified MAC address.MAC 1 to 32 Enter up to 32 MAC addresses to control access.Apply Changes Click to save your changes.
............................................................................................................................................................................................................................................................WiFi Access FilterWiFi setup6-8 3EQ-10280-AAAA-TCZZAEdition 01 February 2011............................................................................................................................................................................................................................................................
7-13EQ-10280-AAAA-TCZZAEdition 01 February 2011............................................................................................................................................................................................................................................................7Firewall setupOverviewPurposeThis chapter explains how to configure the firewall for the CellPipe 7130 RG.Click Firewall Setup in the main menu to open the Firewall Setup menu.ContentsThis chapter covers the following topics:Port ForwardingThe Port Forwarding window enables you to control the incoming requests from the Internet to pass through the port to your local computer.Note: It is recommended that port forwarding be configured with the assistance of your ISP.Select Port Forwarding in the Firewall Setup menu to open the Port Forwarding window; see Figure 7-1.Port Forwarding 7-1Demilitarized Zone 7-3UPnP 7-4Layer 2 Filter 7-5Layer 3 Filter 7-7NAT Passthrough 7-8URL Blocking 7-9Content Screening 7-10Parental Control 7-11
............................................................................................................................................................................................................................................................Port ForwardingFirewall setup7-2 3EQ-10280-AAAA-TCZZAEdition 01 February 2011............................................................................................................................................................................................................................................................Figure 7-1 Port Forwarding windowTable 7-1 describes the fields of the Port Forwarding window.Table 7-1 Field descriptionsField DescriptionName Enter a name for the application you are hosting on your LAN computer; for example, Real Audio.Protocol Select the type of IP protocol(s) used by this application:•ALL•Protocol Number and then enter the protocol number•Known Protocol and then select a protocol:•TCP•UDP•TCP/UDP•ICMP
Firewall setupDemilitarized Zone............................................................................................................................................................................................................................................................3EQ-10280-AAAA-TCZZAEdition 01 February 2011 7-3............................................................................................................................................................................................................................................................Demilitarized ZoneThe Demilitarized Zone window enables you to configure a single computer on the local side to be exposed to the Internet. All incoming packets will be forwarded to this computer.Note: Use the demilitarized zone setting only if the virtual server or port range forwarding options do not provide the level of access required for certain applications. It is recommended that you contact your ISP for assistance.Select Demilitarized Zone in the Firewall Setup menu to access the Demilitarized Zone window; see Figure 7-2. Port Select or enter the TCP/UDP port for which the port forwarding route must be applied.•Known Port and then select a port:•FTP•TFTP•TELNET•SSH•HTTP•HTTPS•SMTP•POP3•DNS•IMAP•Single Port and then enter the port number•Port Range and then enter the port rangeLAN IP Address Select the first radio button to choose a pre-configured LAN host or select the second radio button to enter an IP address manually.LAN Port Select the first radio button to use the same port or port range as the WAN or select the second radio button and enter the LAN port manually.Apply Changes Click to save your changes.Field Description
............................................................................................................................................................................................................................................................UPnPFirewall setup7-4 3EQ-10280-AAAA-TCZZAEdition 01 February 2011............................................................................................................................................................................................................................................................Figure 7-2 Demilitarized Zone windowTable 7-2 describes the fields of the Demilitarized Zone window.Table 7-2 Field descriptionsUPnPUPnP is an open networking standard that allows peer-to-peer network connectivity between devices. It enables software or devices, such as video game consoles, to function properly using NAT.Note: It is recommended that you contact your ISP for assistance.Field DescriptionDemilitarized Zone(DMZ) Select Enable to turn on the demilitarized zone function. Select Disable to turn it off.DMZ Host IP Address Select the first radio button and choose a pre-existing LAN host or select the second radio button to enter an IP address manually.DMZ Timer (Option) To improve security, specify the length of time (in seconds) during which the DMZ is active.Apply Changes Click to save your changes.
Firewall setupLayer 2 Filter............................................................................................................................................................................................................................................................3EQ-10280-AAAA-TCZZAEdition 01 February 2011 7-5............................................................................................................................................................................................................................................................Select UPnP in the Firewall Setup menu to access the UPnP window; see Figure 7-3.Figure 7-3 UPnP windowTable 7-3 describes the fields of the UPnP window.Table 7-3 Field descriptionsLayer 2 FilterSelect Layer 2 Filter in the Firewall Setup menu to access the Layer 2 Filter window; see Figure 7-4.Field DescriptionUPnP Select Enable to turn on the UPnP function. Select Disable to turn off the UPnP function.UPnP Log Select Enable to turn on logging activities. Select Disable to turn off the logging activities.ReadOnly Mode Select Enable to turn on the read-only mode. Select Disable to turn off the read-only mode.Note: In read-only mode, users are unable to change port forwarding settings or any other UPnP enabled application settings.Apply Changes Click to save your changes.
............................................................................................................................................................................................................................................................Layer 2 FilterFirewall setup7-6 3EQ-10280-AAAA-TCZZAEdition 01 February 2011............................................................................................................................................................................................................................................................Figure 7-4 Layer 2 Filter windowTable 7-4 describes the fields of the Layer 2 Filter window.Table 7-4 Field descriptionsField DescriptionFilter Policy Select the policy for filters:•Allow•Deny•Disable
Firewall setupLayer 3 Filter............................................................................................................................................................................................................................................................3EQ-10280-AAAA-TCZZAEdition 01 February 2011 7-7............................................................................................................................................................................................................................................................Layer 3 Filter Select Layer 3 Filter in the Firewall Setup menu to access the Layer 3 Filter window; see Figure 7-5.Figure 7-5 Layer 3 Filter windowTable 7-5 describes the fields of the Layer 3 Filter window.Table 7-5 Field descriptionsEthernet Type Select to use Ethernet Type as the filtering algorithm and enter the applicable Ethernet Type code.Source Mac Address 1 to 10 Select and then enter the source MAC address of the device.Destination Mac Address 1 to 10 Select and then enter the destination MAC address of the device.Apply Changes Click to save your changes.Field DescriptionField DescriptionFilter Name Enter a name for the filtering rule.IP Type Select Dest (destination) or Source depending on the how the rule is going to be used.
............................................................................................................................................................................................................................................................NAT PassthroughFirewall setup7-8 3EQ-10280-AAAA-TCZZAEdition 01 February 2011............................................................................................................................................................................................................................................................NAT PassthroughThe NAT Passthrough window allows you to enable or disable specific protocols from passing through the gateway.Note: This should only be configured with the help of your ISP.Select NAT Passthrough in the Firewall Setup menu to access the NAT Passthrough window; see Figure 7-6.IP Address Enter the IP address of the host that you are blocking.IP Netmask Select the subnet mask of the host that you are blocking.Protocol Select the type of protocol(s) used by the application:•TCP•UDP•BothPort Type Select Dest (destination) or Source depending on the type of application.Starting Port Enter the start port of the ports used by the application.Ending Port Enter the end port of the ports used by the application.Enable Select Enable to apply the filter rule or Disable to turn off the filter rule.DSCP Packet Filter Policy Select Disable to disable the DSCP policy. Select Deny to deny packets that are accessing the Internet with the specified DSCP value in the IP header or select Allow to allow packets that are accessing the Internet with the specified DSCP value in the IP header.DSCP Value Enter a DSCP value between 0 and 63.Apply Changes Click to save your changes.Field Description
Firewall setupURL Blocking............................................................................................................................................................................................................................................................3EQ-10280-AAAA-TCZZAEdition 01 February 2011 7-9............................................................................................................................................................................................................................................................Figure 7-6 NAT Passthrough windowTable 7-6 describes the fields of the NAT Passthrough window.Table 7-6 Field descriptionsURL BlockingThe URL Blocking window enables you to block requests from your local computer to access specific websites.Select URL Blocking in the Firewall Setup menu to access the URL Blocking window; see Figure 7-7.Field DescriptionIPSec Passthrough Select Enable to allow IPSec passthrough. Select Disable to turn off the IPSec passthrough.L2TP Passthrough Select Enable to allow L2TP passthrough. Select Disable to turn off L2TP passthrough.PPTP Passthrough Select Enable to allow PPTP passthrough. Select Disable to turn off PPTP passthrough.Apply Changes Click to save your changes.
............................................................................................................................................................................................................................................................Content ScreeningFirewall setup7-10 3EQ-10280-AAAA-TCZZAEdition 01 February 2011............................................................................................................................................................................................................................................................Figure 7-7 URL Blocking windowTable 7-7 describes the fields of the URL Blocking window.Table 7-7 Field descriptionsContent ScreeningThe Content Screening window enables you to configure keywords to screen website content. If the keywords appear in the website content and content screening is enabled, the firewall will block the user from accessing the website.Note: Compressed and secured pages are not supported.Select Content Screening in the Firewall Setup menu to access the Content Screening window; see Figure 7-8.Field DescriptionName Enter a name for the URL filter.URL Enter a URL or a prefix keyword of the URL you are blocking. Note: If the keyword is too general, you might inadvertently block other websites.Enable Select Enable to apply the URL filter. Select Disable to turn off the URL filter.Add Click to add the URL blocking rule.Edit Click to edit the URL blocking rule.Delete Click to delete the URL blocking rule.
Firewall setupParental Control............................................................................................................................................................................................................................................................3EQ-10280-AAAA-TCZZAEdition 01 February 2011 7-11............................................................................................................................................................................................................................................................Figure 7-8 Content Screening windowTable 7-8 describes the fields of the Content Screening window.Table 7-8 Field descriptionsParental ControlThe Parental Control window enables you to set Internet connection limits on your computer based on the time and day of the week.Select Parental Control in the Firewall Setup menu to access the Parental Control window; see Figure 7-9.Field DescriptionContent Screening Select Enable to apply content screening and block websites that have keywords in their contents. Select Disable to disable content screening.Keyword Enter a keyword to be blocked. Enter only one keyword. If you want to screen multiple keywords, add them as separate rules. The maximum number of keywords allowed is 254.Note: If the keyword is too general, you might inadvertently block other websites.Index The index of rule. The index is created by system.Add Click to add the keyword to the content screening rules.Edit Click to edit the keyword to the content screening rules.Delete Click to delete the keyword to the content screening rules.
............................................................................................................................................................................................................................................................Parental ControlFirewall setup7-12 3EQ-10280-AAAA-TCZZAEdition 01 February 2011............................................................................................................................................................................................................................................................Figure 7-9 Parental Control windowTable 7-9 describes the fields of the Parental Control window.Table 7-9 Field descriptionsField DescriptionName Enter a name for the rule.MAC Address Enter the MAC address of the LAN device.Day Enable the day(s) of the week you want to limit the Internet connection of the client. This is optional.Time Enter a time period (in hours and minutes) that you want to limit the Internet connection of the client. This is optional.Add Click to add the rule.Edit Click to edit the rule.Delete Click to delete the rule.
8-13EQ-10280-AAAA-TCZZAEdition 01 February 2011............................................................................................................................................................................................................................................................8 Advanced setupOverviewThis chapter explains how to configure the advanced settings of the CellPipe 7130 RG such as the route settings, DNS settings, dynamic DNS, system log, IGMP proxy/snooping, and 802.1x.Click Advanced Setup in the main menu to open the Advanced Setup menu.ContentsThis chapter covers the following topics:Route SettingsThe Route Settings window enables you to configure static and dynamic routes for routing packets from one network to another network.Select Route Settings in the Advanced Setup menu to access the Route Settings window; see Figure 8-1.Route Settings 8-1DNS Settings 8-3Dynamic DNS 8-4System Log 8-5IGMP Proxy/Snooping 8-6802.1x Config 8-7
............................................................................................................................................................................................................................................................Route SettingsAdvanced setup8-2 3EQ-10280-AAAA-TCZZAEdition 01 February 2011............................................................................................................................................................................................................................................................Figure 8-1 Route Settings windowTable 8-1 describes the fields of the Route Settings window.Table 8-1 Field descriptionsField DescriptionStatic RoutingIP Destination Enter the IP address of the destination network.IP Netmask Select the subnet mask of the destination network.Gateway Enter the IP address of the gateway for the destination network.Metric In order to determine the best route, a value is used to specify the cost of the route (the metric value). Enter the metric value in the metric field. IP routing uses hop count as measurement of the metric.
Advanced setupDNS Settings............................................................................................................................................................................................................................................................3EQ-10280-AAAA-TCZZAEdition 01 February 2011 8-3............................................................................................................................................................................................................................................................DNS SettingsThe DNS Settings window enables you to configure the domain name and IP address of the domain name.Note: You can set up to 64 entries.Select DNS Settings in the Advanced Setup menu to access the DNS Settings window; see Figure 8-2.Figure 8-2 DNS Settings windowTable 8-2 describes the fields of the DNS Settings window.Table 8-2 Field descriptionsInterface Select LAN or WAN(DHCP1) interface. The packets sent to the addresses of the destination IP address are sent through this interface. However, for the WAN interface it will depend on the WAN configuration you choose and how it is defined.Dynamic Routing Select Enable to use dynamic routing instead of static. Dynamic routing enables the router to adapt to changes in the network and exchange rating tables with other routers. Select Disable to turn off dynamic routing.Apply Changes Click to save your changes.Field DescriptionField DescriptionDomain Name Enter the domain name to which you want to connect.IP Address Enter the IP address of the Static DNS.
............................................................................................................................................................................................................................................................Dynamic DNSAdvanced setup8-4 3EQ-10280-AAAA-TCZZAEdition 01 February 2011............................................................................................................................................................................................................................................................Dynamic DNSThe Dynamic DNS (DDNS) window enables you to configure your registered domain name with a dynamic IP address.Note: Before you can use this feature, you need to register for a DDNS service at one of the supported DDNS service providers; see DynDNS.org or ChangeIP.com.Click on Dynamic DNS in the Advanced Setup menu to access the Dynamic DNS (DDNS) window; see Figure 8-3.Figure 8-3 Dynamic DNS windowTable 8-3 describes the fields of the Dynamic DNS (DDNS) window.Table 8-3 Field descriptionsAdd Click to add the DNS settings and save your changes.Field DescriptionField DescriptionDDNS Service If you have registered a DDNS, select the DDNS service. Select Disable to turn off DDNS.User Name Enter the username of your DDNS account.Password Enter the password of your DDNS account.Host Name Enter the host name.Apply Changes Click to save your changes.
Advanced setupSystem Log............................................................................................................................................................................................................................................................3EQ-10280-AAAA-TCZZAEdition 01 February 2011 8-5............................................................................................................................................................................................................................................................System LogThe System Log window enables you to view the system logs and to send them to a remote system log server.Click on System Log in the Advanced Setup menu to access the system log window; see Figure 8-4.Figure 8-4 System Log windowTable 8-4 describes the fields of the System Log window.Table 8-4 Field descriptionsField DescriptionLog Size (Lines) Select the number of lines to display in the log.Remote Logging Select LAN or WAN for the remote logging server. Select Disable to turn off remote logging.Remote Server Enter the IP address of the remote logging server.
............................................................................................................................................................................................................................................................IGMP Proxy/SnoopingAdvanced setup8-6 3EQ-10280-AAAA-TCZZAEdition 01 February 2011............................................................................................................................................................................................................................................................IGMP Proxy/SnoopingThe IGMP Proxy/Snooping window enables you to setup LAN-side IGMP support that enables the LAN-side user to receive multicast traffic.Click on IGMP Proxy/Snooping in the Advanced Setup menu to access the IGMP Proxy/Snooping window; see Figure 8-5.Apply Changes Click to save your changes and to view the log.If you are configuring remote logging, click Apply Changes after modifying the remote logging and remote server fields.Time (read-only) The time that the event occurred.Module (read-only) The type of module involved in the event.Level (read-only) The level of logging activity:•EMERG•ALERT•CRIT•ERR•WARNING•NOTICE•INFO•DEBUGMessage The details of the event that occurred.Field Description
Advanced setup802.1x Config............................................................................................................................................................................................................................................................3EQ-10280-AAAA-TCZZAEdition 01 February 2011 8-7............................................................................................................................................................................................................................................................Figure 8-5 IGMP Proxy/Snooping windowTable 8-5 describes the fields of the IGMP Proxy/Snooping window.Table 8-5 Field descriptions802.1x Config The 802.1x Config window enables you to setup the 802.1x configuration. 802.1x is an authentication mechanism for clients connecting to an IEEE 802 network such as Ethernet (access) networks and 802.11 (public) wireless LANs.Click on 802.1x Config in the Advanced Setup menu to access the 802.1x Config window; see Figure 8-6.Field DescriptionIGMP Enable Select Enable to allow IGMP support. Select Disable to turn off IGMP support.IGMP Version Select the IGMP version to use.IGMP Enabled Ports Enable LAN Port 1 to 4 to enable IGMP support for each selected LAN port.IGMP Aging Time Enter the IGMP aging time in seconds.Apply Changes Click to save your changes.
............................................................................................................................................................................................................................................................802.1x ConfigAdvanced setup8-8 3EQ-10280-AAAA-TCZZAEdition 01 February 2011............................................................................................................................................................................................................................................................Figure 8-6 802.1 x Config windowTable 8-6 describes the fields of the 802.1x Config window.Table 8-6 Field descriptionsField DescriptionEAP identify Enter the EAP identity.Authentication Mode Select Unidirectional or Mutual support for each authentication mode.Apply Changes Click to save your changes.
9-13EQ-10280-AAAA-TCZZAEdition 01 February 2011............................................................................................................................................................................................................................................................9QoS PTM setupOverviewThis chapter explains how to configure the QoS settings via PTM. QoS is the ability to provide better service to selected applications and data flows.Click QoS PTM Setup in the main menu to open the QoS PTM Setup menu.ContentsThis chapter covers the following topics:QoS OverviewThe QoS Overview window allows you to see all current QoS PTM settings.Select QoS Overview in the QoS PTM Setup menu to access the QoS Overview window; see Figure 9-1.QoS Overview 9-1QoS Scheduler 9-2QoS Policy 9-5QoS Phone 9-7QoS ALG 9-8QoS Defaults 9-10QoS MAC 9-12
............................................................................................................................................................................................................................................................QoS SchedulerQoS PTM setup9-2 3EQ-10280-AAAA-TCZZAEdition 01 February 2011............................................................................................................................................................................................................................................................Figure 9-1 QoS Overview windowTable 9-1 describes the fields of the QoS Overview window.Table 9-1 Field descriptionsQoS SchedulerThe QoS Scheduler window allows you to enable and disable the scheduler protocol and determine the upstream bandwidth.Select QoS Scheduler in the QoS PTM Setup menu to access the QoS Scheduler window; see Figure 9-2.Field DescriptionPrecedence (read-only) Presents the priority of each QoS rule (Precedence 1 is the highest priority).Source (read-only) IP address of the source host.Destination (read-only) IP address of the destination host.Protocol (read-only) The protocol type for the QoS rule.Source Port (read-only) Port number of the source host.Destination Port (read-only) Port number of the destination host.QoS Classification (read-only) The classification of the QoS rule:•Original ToS Tag: the queue is assigned according to the ToS value of incoming traffic.•Specified Queue: incoming traffic is assigned to a specific queue (0 to 7).ToS/DSCP Settings (read-only) The ToS/DSCP marking setting for incoming traffic.CoS Settings (read-only) CoS setting for the QoS rule.
QoS PTM setupQoS Scheduler............................................................................................................................................................................................................................................................3EQ-10280-AAAA-TCZZAEdition 01 February 2011 9-3............................................................................................................................................................................................................................................................Figure 9-2 QoS Upstream Scheduler windowTable 9-2 describes the fields of the QoS Upstream Scheduler window.Table 9-2 Field descriptionsField DescriptionQoS Enable Select Enable to activate the QoS scheduler. Select Disable to turn off the QoS scheduler.Scheduler Type Select the QoS scheduler type:•Strict Priority: delivers high priority (7 is the highest) traffic first and then lower priority traffic when higher queues are empty.•Min - Max Bandwidth: specifies the minimum and maximum bandwidth for each queue.Aggregate Rate Limiter Enter an upstream bandwidth value from 100 to 200000 Kb/s for your WAN connection. The default value is 50000 Kb/s.7. Urgent Specify the minimum and maximum bandwidth for the urgent queue.6. Real Time Specify the minimum and maximum bandwidth for the real-time queue.5. High Specify the minimum and maximum bandwidth for the high queue.
............................................................................................................................................................................................................................................................QoS PTM setup9-4 3EQ-10280-AAAA-TCZZAEdition 01 February 2011............................................................................................................................................................................................................................................................4. Low Specify the minimum and maximum bandwidth for the low queue.3. Premium Specify the minimum and maximum bandwidth for the premium queue.2. Critical Specify the minimum and maximum bandwidth for the critical queue.1. Medium Specify the minimum and maximum bandwidth for the medium queue.Apply Changes Click to save your changes.Field Description
QoS PTM setupQoS Policy............................................................................................................................................................................................................................................................3EQ-10280-AAAA-TCZZAEdition 01 February 2011 9-5............................................................................................................................................................................................................................................................QoS PolicyThe QoS Policy window enables you to group upstream traffic into data flows according to the source address, destination address, source port, and destination port.Select QoS Policy in the QoS PTM Setup menu to access the QoS Policy window; see Figure 9-3.Figure 9-3 QoS Policy windowTable 9-3 describes the fields of the QoS Policy window.
............................................................................................................................................................................................................................................................QoS PolicyQoS PTM setup9-6 3EQ-10280-AAAA-TCZZAEdition 01 February 2011............................................................................................................................................................................................................................................................Table 9-3 Field descriptionsField DescriptionSourceIP Address Select the radio button and enter the IP address of the source host.Netmask Select the subnet mask of the source host.Interface Select the radio button and select a connection to configure its QoS policy.MAC Address Select the radio button and enter the MAC address.DestinationIP Address Enter the IP address of the destination host.Netmask Select the subnet mask of the destination host.Protocol Click Select Protocol to choose a protocol.Source Port Enter the range of source ports for this QoS policy.Destination Port Enter the range of destination ports for this QoS policy.QoS ClassificationQueue Select one of the following:•Original ToS Tag to assign the queue according to the incoming ToS value.•Specified Queue and enter a queue number (0 to 7) to assign to the incoming traffic.ToS/DSCP Remarking Select one of the following:•Keep Original ToS/DSCP to retain the original value.•New ToS Value and enter a queue number (0 to 7) to assign to the incoming traffic.•New DSCP Value and enter a DSCP value (0 to 63).CoS (p-bit) Remarking Select one of the following:•Keep CoS Value to retain the original value.•New CoS Value to set a new CoS value for incoming traffic.•Align CoS with ToS value to set CoS same as the ToS value for incoming traffic.Add Click to add the policy and save your changes.OverviewTarget Upstream or Downstream. Target 1 is the highest priority.
QoS PTM setupQoS Phone............................................................................................................................................................................................................................................................3EQ-10280-AAAA-TCZZAEdition 01 February 2011 9-7............................................................................................................................................................................................................................................................QoS PhoneThe QoS Phone window enables you to configure DSCP value and CoS value of SIP and RTP Sessions.Select QoS Phone in the QoS PTM Setup menu to access the QoS Phone window; see Figure 9-4.Source IP IP address of the source host.Netmask Subnet mask of the source IP address.Source Port Port number of the source host.Destination IP IP address of the destination host.Netmask Subnet mask of the destination IP address.Destination Port Port number of the destination host.Protocol The protocol type for this QoS policy.Priority The priority queue (0 to 7) used by the traffic.CoS CoS value of the QoS policy.ToS/DSCP ToS/DSCP marking setting for incoming traffic.Change Precedence Select a QoS rule precedence number and then select where to move it:•Up: move this QoS rule to higher priority.•Down: move this QoS rule to lower priority.•Delete: remove this QoS rule.Click Apply to change the precedence.Field Description
............................................................................................................................................................................................................................................................QoS ALGQoS PTM setup9-8 3EQ-10280-AAAA-TCZZAEdition 01 February 2011............................................................................................................................................................................................................................................................Figure 9-4 QoS Phone windowTable 9-4 describes the fields of the QoS Phone window.Table 9-4 Field descriptionsQoS ALGThe QoS ALG window enables you to configure SIP and RTP. SIP is used by VoIP and RTP is the protocol for transferring real-time data (such as interactive audio and video).Select QoS ALG in the QoS PTM Setup menu to access the QoS ALG window; see Figure 9-5.Field DescriptionSIP Sessions/RTP SessionsDSCP value Check the check box to enter a DSCP value (0 to 63).CoS value Check the check box to enter a CoS value (0 to 7).Apply Changes Click to save your changes.
QoS PTM setupQoS ALG............................................................................................................................................................................................................................................................3EQ-10280-AAAA-TCZZAEdition 01 February 2011 9-9............................................................................................................................................................................................................................................................Figure 9-5 QoS ALG windowTable 9-5 describes the fields of the QoS ALG window.Table 9-5 Field descriptionsField DescriptionSIP ALG QoS Enable Select Enable to turn on the SIP ALG QoS. Select Disable to turn off the SIP ALG QoS.
............................................................................................................................................................................................................................................................QoS DefaultsQoS PTM setup9-10 3EQ-10280-AAAA-TCZZAEdition 01 February 2011............................................................................................................................................................................................................................................................QoS DefaultsThe QoS Defaults window enables you to configure the default QoS policy for each WAN connection.Select QoS Defaults in the QoS PTM Setup menu to access the QoS Defaults window; see Figure 9-6.SIP Sessions/RTP SessionsQueue Select one of the following:•Original ToS Tag to assign the queue according to the incoming ToS value.•Specified Queue and enter a queue number (0 to 7) to assign to the incoming traffic.ToS/DSCP Remarking Select one of the following:•Keep Original ToS/DSCP to retain the original value.•New ToS Value and enter a queue number (0 to 7) to assign to the incoming traffic.•New DSCP Value and enter a DSCP value (0 to 63).CoS (p-bit) Remarking Select one of the following:•Keep CoS Value to retain the original value.•New CoS Value to set a new CoS value for incoming traffic.•Align CoS with ToS value to set CoS same as the ToS value for incoming traffic.Apply Changes Click to save your changes.Field Description
QoS PTM setupQoS Defaults............................................................................................................................................................................................................................................................3EQ-10280-AAAA-TCZZAEdition 01 February 2011 9-11............................................................................................................................................................................................................................................................Figure 9-6 QoS Defaults windowTable 9-6 describes the fields of the QoS Defaults window.Table 9-6 Field descriptionsField DescriptionInterface Select a WAN connection to configure its default QoS policy.QoS Upstream ClassificationQueue Select one of the following:•Original ToS Tag to assign the queue according to the incoming ToS value.•Specified Queue and enter a queue number (1 to 7) to assign to the incoming traffic.
............................................................................................................................................................................................................................................................QoS MACQoS PTM setup9-12 3EQ-10280-AAAA-TCZZAEdition 01 February 2011............................................................................................................................................................................................................................................................QoS MACThe QoS MAC window enables you to configure a QoS policy for a specific device by MAC address when the gateway is operating in bridge mode.Select QoS MAC in the QoS PTM Setup menu to access the QoS MAC window; see Figure 9-7.ToS/DSCP Remarking Select one of the following:•Keep Original ToS/DSCP to retain the original value.•New ToS Value and enter a queue number (0 to 7) to assign to the incoming traffic.•New DSCP Value and enter a DSCP value (0 to 63).CoS (p-bit) Remarking Select one of the following:•Keep CoS Value to retain the original value.•New CoS Value to set a new CoS value for incoming traffic.•Align CoS with ToS value to set CoS same as the ToS value for incoming traffic.OverviewInterface Name The Interface name of WAN connection to configure its QoS policy.QoS Upstream Classification The classification of the QoS rule:•Original ToS Tag: the queue is assigned according to the ToS value of incoming traffic.•Specified Queue: incoming traffic is assigned to a specific queue (0 to 7).ToS/DSCP Settings The ToS/DSCP marking setting for incoming traffic.CoS Settings CoS setting for the QoS rule.Field Description
QoS PTM setupQoS MAC............................................................................................................................................................................................................................................................3EQ-10280-AAAA-TCZZAEdition 01 February 2011 9-13............................................................................................................................................................................................................................................................Figure 9-7 QoS MAC windowTable 9-7 describes the fields of the QoS MAC window.Table 9-7 Field descriptionsField DescriptionBridge Destination MAC Address Specify the MAC address of QoS service user.Queue Specify which queue (1 to 7) will be assigned to this MAC address.CoS Specify the CoS value (0 to 7) that will be marked on packets coming from the MAC address.Add Click to add the rule.
............................................................................................................................................................................................................................................................QoS MACQoS PTM setup9-14 3EQ-10280-AAAA-TCZZAEdition 01 February 2011............................................................................................................................................................................................................................................................
10-13EQ-10280-AAAA-TCZZAEdition 01 February 2011............................................................................................................................................................................................................................................................10 TelephonyOverviewThe CellPipe 7130 RG Telephony menu enables you to configure the settings for your VoIP account and view the calling log.Click the Telep ho ny drop-down menu to open the Tel e phony menu.ContentsThis chapter covers the following topics.Account SetupYour VoIP account setup can be configured here.Note: Some account information, such as the phone number and username, is provided by your VoIP service provider. Please have all the provided information handy when configuring your accounts.Select Account Setup in the Telep h o n y menu to access the Account Setup window; see Figure 10-1.Account Setup 10-1Service Settings 10-4SIP Server Settings 10-8RTP/Codecs settings 10-10Account & Line Table 10-12Call History 10-13Other Settings 10-14
............................................................................................................................................................................................................................................................Account SetupTelephony10-2 3EQ-10280-AAAA-TCZZAEdition 01 February 2011............................................................................................................................................................................................................................................................Figure 10-1 Account Setup windowTable 10-1 describes the fields of the Account Setup window.Table 10-1 Field descriptionsField DescriptionConfiguration of Account Select a VoIP account to configure or select Create VoIP Account to configure a new account.Enable this Account Check the check box to enable the account to register to the VoIP service provider.
Account SetupTelephony............................................................................................................................................................................................................................................................3EQ-10280-AAAA-TCZZAEdition 01 February 2011 10-3............................................................................................................................................................................................................................................................Phone Number Enter the phone number of the account.Display Name Enter the display name for the account.User Name The user part of the Address of Record SIP URI.Authentication User Name Enter the username of the account.Authentication Password Enter the password for the username.Realm Enter the realm for the account to authenticate.Do Not Disturb When the checkbox is "checked" the Do Not Disturb feature is activated. This will block all incoming phone calls to this number. The phone will not ring when this service is activated.Hide Calling Identity When the checkbox is "checked" the "Hide Calling identity" feature is activated. This will hide your identity when you make outgoing calls.Anonymous Call Rejection When the checkbox is "checked" the Anonymous Call Rejection" feature is activated. This will block an incoming call in case the remote party has activated the "Hide Calling Identity" feature for that call. So anynymous calls are rejected by the system when this service is activated.Call Forwarding Unconditional When the checkbox is "checked" the "Call Forwarding Unconditional" feature is activated. You must enter a phone number in the Forward To Number (FTN) field. The system will forward an incoming call to this FTN when this VoIP account is busy. Call Forwarding On Busy When the checkbox is "checked" the "Call Forwarding on Busy" feature is activated.You must enter a phone number in the Forward To Number (FTN) field. The system will forward an incoming call to this FTN. Call Forwarding No Reply When the checkbox is "checked" the "Call Forwarding No Reply" feature is activated. You must enter a phone number in the Forward To Number (FTN) field. The system will forward an incoming call to this FTN when this VoIP account is busy. Save Click to save your changes.Activate VoIP Account Click to register your account with your VoIP service provider.Field Description
............................................................................................................................................................................................................................................................Service SettingsTelephony10-4 3EQ-10280-AAAA-TCZZAEdition 01 February 2011............................................................................................................................................................................................................................................................Note: If you checked all these three features: Do Not Disturb, Anonymous Call Rejection and Call Forwarding Unconditional, The priorities are:1. Do Not Disturb.2. Anonymous Call Rejection.3. Call Forwarding Unconditional.For example, an incoming call will be rejected and the caller will receive a busy signal; the call will not be rejected if anonymous, nor forwarded to the specified number.Service SettingsThe Service Settings window enables you to configure advanced settings for the VoIP accounts such as call waiting and third party conference call.Note: Changes made to the service settings apply to all VoIP accounts.It is recommended that you contact your VoIP service provider for assistance with configuring the service settings. Depending on your account, some features might not be available.Select Service Settings in the Tele p ho n y menu to access the Service Settings window; see Figure 10-2.
Service SettingsTelephony............................................................................................................................................................................................................................................................3EQ-10280-AAAA-TCZZAEdition 01 February 2011 10-5............................................................................................................................................................................................................................................................Figure 10-2 Service Settings windowTable 10-2 describes the fields of the Service Settings window.
............................................................................................................................................................................................................................................................Service SettingsTelephony10-6 3EQ-10280-AAAA-TCZZAEdition 01 February 2011............................................................................................................................................................................................................................................................Table 10-2 Field descriptionsField DescriptionHide Calling Identity (Per Call)Service Code The activation code for hiding your account information when making a call.Call WaitingActive Enable Active to turn on call waiting.CW Alerting Timer Select a time interval for the call waiting alert.Service Code The service codes for activation, deactivation, and interrogation.3 Party ConferenceActive Enable Active to turn on conference call.Message Wait IndicationActive Enable Active to turn on the message wait indicator when a message has been received.Notify Method Enable a method of notification for message wait indication:•Unsolicited: The CellPipe 7130 RG is able to receive unsolicited "message wait" NOTIFY messages. No SUBSCRIBE is used.•Subscribe/Notify: The CellPipe 7130 RG will initiate a SUBSCRIBE/NOTIFY dialogue in which "message wait" NOTIFY messages will be received. Enter the number of seconds that your VoIP service should provide. It is the expire time in seconds of your subscription to the voicemail service. The SIP user agent will refresh this subscription automatically before this timer runs out. Reminder Notification Enable one of the following as the message wait indication:•If Stutter Dial Tone is selected to indicate a new message has arrived, a stutter dial tone will be played when the phone is off the hook.•If Visual “Message” LED is selected to indicated a new message has arrived, the Message LED on the front panel of the CellPipe 7130 RG will start blinking.Hot Line/Warm Line
Service SettingsTelephony............................................................................................................................................................................................................................................................3EQ-10280-AAAA-TCZZAEdition 01 February 2011 10-7............................................................................................................................................................................................................................................................Active Enable Active to use the hot line and warm line feature.Warm Line Timer Select a time period from the drop-down menu. Warm line will be activated after the timer has expired.Hot Line destination Enter a destination phone number for the hot line. When hot line is activated, picking up the phone will automatically place a call to the hot line destination.Warm Line destination Enter a destination phone number for the warm line. When warm line is activated, picking up the phone will automatically place a call to the warm line destination after the warm line timer has expired.Service Code The service codes for activation, deactivation, and interrogation.Session TimerActive Enable Active to turn on the session timer. When session timer is enabled, the CellPipe 7130 RG will periodically send a refresh message to refresh the session.Default Session Expire Enter the default number of seconds SIP session can remain idle before automatically disconnecting. Default value is 1800.Minimal Session Expire Enter the minimum number of seconds SIP session can remain idle before automatically disconnecting. Minimun value is 90.Refresh Method Select Invite or Update from the drop-down menu. This will be the type of message to send for refreshing session.Refresh Preference Select a refresher preference from the drop-down menu. Select None to let CellPipe 7130 RG decide. Select UAC to let caller refresh the session. Select UAS to let the receiver of the call refresh the session.Don’t DisturbService Code The service codes for activation, deactivation, and interrogation of your do not disturb service.Anonymous Call RejectionField Description
............................................................................................................................................................................................................................................................SIP Server SettingsTelephony10-8 3EQ-10280-AAAA-TCZZAEdition 01 February 2011............................................................................................................................................................................................................................................................SIP Server SettingsThe Server Settings window enables you to configure the session initiated protocol (SIP) settings for the VoIP accounts.Note: It is recommended that you contact your VoIP service provider for assistance with configuring the server settings.Select SIP Server Settings in the Teleph o n y menu to access the Server Settings window; see Figure 10-3.Service Code The service codes for activation, deactivation, and interrogation of your anonymous call rejection service.Call ForwardingEnable Splash Ring Enable to receive a reminder when a incoming call is forwarded unconditionally.Unconditional Service Code The unconditional service codes for activation, deactivation, and interrogation of your call forwarding service.On Busy Service Code The on busy service codes for activation, deactivation, and interrogation of your call forwarding service.No Reply Service Code Select a time in seconds that the incoming call should wait before being forwarded. The default value is 20 seconds.The no reply service codes for activation, deactivation, and interrogation of your call forwarding service.Save Click to save your changes.Cancel Click to clear your settings.Field Description
SIP Server SettingsTelephony............................................................................................................................................................................................................................................................3EQ-10280-AAAA-TCZZAEdition 01 February 2011 10-9............................................................................................................................................................................................................................................................Figure 10-3 SIP Server Settings windowTable 10-3 describes the fields of the SIP Server Settings window.Table 10-3 Field descriptionsField DescriptionRegistrar Server Enter the Fully Qualified Domain Name (FQDN) or IP address of the SIP registrar server of your VoIP provider.Registrar Server Port Enter the port number of the SIP registration server.Outbound Proxy Enter the Fully Qualified Domain Name (FQDN) or IP address of the Outbound Proxy server of your Vo I P p r o v i d e r.Outbound Proxy Port Enter the port number of the outbound proxy server.Register Expires Enter the number of seconds that your SIP account is registered with the SIP registrar server before it is deleted. The default value is 3600 seconds.Transport Select the appropriate transport protocol for the user agent:•UDP•TCPSave Click to save your changes.Activate VoIP Account Click to register the account with your VoIP service provider.
............................................................................................................................................................................................................................................................RTP/Codecs settingsTelephony10-10 3EQ-10280-AAAA-TCZZAEdition 01 February 2011............................................................................................................................................................................................................................................................RTP/Codecs settingsThe RTP/Codecs settings window allows you to setup the codecs and ports for your voice traffic.A codec (coder/decoder) codes analog voice signals into digital signals and decodes the digital signals back into analog voice signals. Select RTP/Codecs Settings in the Telephon y menu to access the RTP/Codecs Settings window; see Figure 10-4.Clear Click to clear your settings.Field Description
RTP/Codecs settingsTelephony............................................................................................................................................................................................................................................................3EQ-10280-AAAA-TCZZAEdition 01 February 2011 10-11............................................................................................................................................................................................................................................................Figure 10-4 RTP/Codecs Settings windowTable 10-4 describes the fields of the RTP/Codecs Settings window.Table 10-4 Field descriptionsField DescriptionVoice CodecPrimary Codec/Secondary Codec/Tertiary Codec/Quaternary CodecSelect the priorities of your codec.Fax/ModemT.38 Enable to allow the device to send fax messages through IP networks.MAX Bit Rate Select the maximum bit rate in b/s for fax messages.
............................................................................................................................................................................................................................................................Account & Line TableTelephony10-12 3EQ-10280-AAAA-TCZZAEdition 01 February 2011............................................................................................................................................................................................................................................................Account & Line TableThe Account & Line Table enables you to specify which VoIP accounts are associated with your phone ports/lines.Select Account & Line Table in the Tel eph o ny menu to access the Account & Line Table window; see Figure 10-5.Rate Management Select the data rate management:•Select Network data rate management to require that the training signal be transferred over the network.•Select Local data rate management to require that the training signal be generated locally.The default is Network.Fax Pass Through Enable to apply fax passthrough.RTP PortsMin Port Enter the minimum port of the RTP listening port range.Max Port Enter the maximum port of the RTP listening port range.DTMF Mode Select how the device handles the tones that your telephone makes when the phone buttons are pressed.•Select RFC2833 to send the DTMF tones in RTP packets.•Select SIP INFO to send the DTMF tones in SIP messages.•Select INBAND to send the DTMF tones in the voice data stream.Note: Please consult your VoIP service provider for details.Save Click to save your changes.Cancel Click to clear your settings.Field Description
Call HistoryTelephony............................................................................................................................................................................................................................................................3EQ-10280-AAAA-TCZZAEdition 01 February 2011 10-13............................................................................................................................................................................................................................................................Figure 10-5 Account and Line Table windowTable 10-5 describes the fields of the Account & Line Table window.Table 10-5 Field descriptionsCall HistoryThe Call History window displays the call statistics and call log of your VoIP accounts.Select Call History in the Tel e pho n y menu to access the Call History window; see Figure 10-6.Field DescriptionOutgoing Call use phone number Select the VoIP account to be associated with Line1 and Line2. This VoIP account (phone number) will be used as the "Calling number" when initiating a call from the corresponding Line.Incoming Call use phone number Select which Line will ring when you receive an incoming call for a certain VoIP account (phone number). When you create a VoIP account, a phone number is added by the system in the "Incoming Call use phone number" list. When you delete a VoIP account, the corresponding phone number is removed from this list.Save Click to save your changes.Activate VoIP Account Click to register the account with your VoIP service provider.Cancel Click to clear your settings.
............................................................................................................................................................................................................................................................Other SettingsTelephony10-14 3EQ-10280-AAAA-TCZZAEdition 01 February 2011............................................................................................................................................................................................................................................................Figure 10-6 Call History windowTable 10-6 describes the fields of the Call History window.Table 10-6 Field descriptionsOther SettingsThe Other Settings window allows you to change the profile for various countries in order for that country’s telephone to operate.Select Other Settings in the Te l e ph on y menu to access the Other Settings window; see Figure 10-7.Field DescriptionVoIP Account Select the VoIP account(s) to display the selected account(s) statistics and logs.Call type Select the type of calls to display the specified type of calls statistics and logs.
Other SettingsTelephony............................................................................................................................................................................................................................................................3EQ-10280-AAAA-TCZZAEdition 01 February 2011 10-15............................................................................................................................................................................................................................................................Figure 10-7 Other Settings windowTable 10-7 describes the fields of the Other Settings window.Table 10-7 Field descriptionsField DescriptionCountry Select a country from the list. It will change ring cadence, impedence and DC feed settings to meet that country's requirement. You must reboot the CellPipe 7130 RG for your changes to take effect.DTMF Only one protocol is available, ETSI EN 300 659-1CID Choose between two different types of CID to specify how the CID are transmitted to the phone. Each CID type has its own protocols.FSK Choose between ETSI or Telecordia.Save Click to save your changes.
............................................................................................................................................................................................................................................................Other SettingsTelephony10-16 3EQ-10280-AAAA-TCZZAEdition 01 February 2011............................................................................................................................................................................................................................................................
11-13EQ-10280-AAAA-TCZZAEdition 01 February 2011............................................................................................................................................................................................................................................................11 UtilitiesOverviewThis chapter explains how to configure the utilities of the CellPipe 7130 RG.Click Utilities in the main menu to open the Utilities menu.ContentsThis chapter covers the following topics:Configuration BackupThe Configuration Backup window enables you to backup your configuration of the CellPipe 7130 RG to a file and store it on your computer.Select Configuration Backup in the Utilities menu to access the Configuration Backup window; see Figure 11-1.Configuration Backup 11-1Configuration Restore 11-2Firmware Upgrade 11-3System Settings 11-4Management Access Control 11-7CWMP Management 11-8Connection Test 11-10802.1x CA Upload 11-11Restore Factory Defaults 11-11Reboot Gateway 11-12RGAM Management 11-13
............................................................................................................................................................................................................................................................Configuration RestoreUtilities11-2 3EQ-10280-AAAA-TCZZAEdition 01 February 2011............................................................................................................................................................................................................................................................Figure 11-1 Configuration Backup windowClick Backup to save your system configuration.Configuration RestoreThe Configuration Restore window enables you to restore a saved configuration of the CellPipe 7130 RG from a backup file.CAUTIONRestoring a stored configuration will overwrite any existing configurations.Select Configuration Restore in the Utilities menu to access the Configuration Restore window; see Figure 11-2.Figure 11-2 Configuration Restore windowTable 11-1 describes the fields of the Configuration Restore window.
UtilitiesFirmware Upgrade............................................................................................................................................................................................................................................................3EQ-10280-AAAA-TCZZAEdition 01 February 2011 11-3............................................................................................................................................................................................................................................................Table 11-1 Field descriptionsFirmware UpgradeThe Firmware Upgrade window enables you to update the firmware of the CellPipe 7130 RG. Note: The new firmware file must be downloaded and saved to your computer or a storage device before uploading.WARNINGDo not turn off the power or disturb the system during a firmware upgrade.Select Firmware Upgrade in the Utilities menu to access the Firmware Upgrade window; see Figure 11-3.Figure 11-3 Firmware Upgrade windowTable 11-2 describes the fields of the Firmware Upgrade window.Field DescriptionRestore Configuration Click Browse and select a configuration backup file to restore.Restore Click to restore the configuration.
............................................................................................................................................................................................................................................................System SettingsUtilities11-4 3EQ-10280-AAAA-TCZZAEdition 01 February 2011............................................................................................................................................................................................................................................................Table 11-2 Field descriptionsSystem SettingsThe System Settings window enables you to change the web administrator username and password and configure settings such as the time zone, NTP, and daylight savings.Note: It is highly recommended that you change the default administrator username and password and the default Telnet username and password.Select System Settings in the Utilities menu to access the System Settings window; see Figure 11-4.Field DescriptionCurrent Firmware The current firmware version.Update Firmware Click Browse to locate and select the firmware upgrade file to upload.New firmware is available from http://www.alcatel-lucent.com/wps/portal/support. Note: You must obtain the upgrade file before uploading.Upgrade Firmware Click to update the firmware.
UtilitiesSystem Settings............................................................................................................................................................................................................................................................3EQ-10280-AAAA-TCZZAEdition 01 February 2011 11-5............................................................................................................................................................................................................................................................Figure 11-4 System Settings windowTable 11-3 describes the fields of the System Settings window.
............................................................................................................................................................................................................................................................System SettingsUtilities11-6 3EQ-10280-AAAA-TCZZAEdition 01 February 2011............................................................................................................................................................................................................................................................Table 11-3 Field descriptionsField DescriptionGUI SettingsAdministrator Login Enter a new administrator username.Administrator Password Enter the current administrator password.Note: If this is the first time the admin password is being changed, the default admin password is admin.Administrator New Password Enter a new administrator password.Administrator Password Confirmation Retype the new password to confirm.User Login Enter a new username.User Password Enter the current user password.Note: If this is the first time the user password is changed, the default user password is user.User New Password Enter a new user password.User Password Confirmation Retype the new password to confirm.Telnet SettingsRoot Password Enter the current Telnet root password.Note: If this is the first time the root password is changed, the default root password is admin.Root New Password Enter a new Telnet password.Root Password Confirmation Retype the new password to confirm.Date & Time SettingsLocal Date Displays the current date according to the time zone configuration.Local Time Displays the current time according to the time zone configuration.Get Time From Your PC Click to set the time according to your PC.Time Zone SettingsTime Zone Select your time zone.NTP Server 1 to 3 Enter the IP address or URL of the NTP server.Time Interval Enter an interval time in hours.Daylight Saving Select Enable to turn on daylight savings. Select Disable to turn off daylight savings.
UtilitiesManagement Access Control............................................................................................................................................................................................................................................................3EQ-10280-AAAA-TCZZAEdition 01 February 2011 11-7............................................................................................................................................................................................................................................................Management Access ControlThe Management Access Control window enables you to control who can access the service provided by the gateway.Note: It is recommended that you consult your ISP before configuring access.Select Management Access in the Utilities menu to access the Management Access Control window; see Figure 11-5.Figure 11-5 Management Access Control windowTable 11-4 describes the fields of the Management Access Control window.Start/End If you have enabled daylight savings, select the Month, Week, Day, Hour, and Minute for the daylight savings to start and end.Apply Changes Click to save your changes.Field Description
............................................................................................................................................................................................................................................................CWMP ManagementUtilities11-8 3EQ-10280-AAAA-TCZZAEdition 01 February 2011............................................................................................................................................................................................................................................................Table 11-4 Field descriptionsCWMP ManagementThe CWMP Management window enables you to configure remote access of the CellPipe 7130 RG.Select CWMP Management in the Utilities menu to access the CWMP Management window; see Figure 11-6.Field DescriptionHTTP Access to GatewayTelnet Access to GatewaySSH Access to GatewayTFTP Access to GatewaySelect one of the following settings:•Disable•From LAN only•From WAN only•From LAN and WANWAN Ping Reply Select Enable to allow the WAN interface to respond to the echo request from the default WAN connection. Select Disable to deny the WAN interface from responding to the echo request from the default WAN connection.Firewall Stealth Mode Select Enable to allow firewall to drop all stealth or unknown traffic. Select Disable to accept all unknown traffic.Apply Changes Click to save your changes.
UtilitiesCWMP Management............................................................................................................................................................................................................................................................3EQ-10280-AAAA-TCZZAEdition 01 February 2011 11-9............................................................................................................................................................................................................................................................Figure 11-6 CWMP Management windowTable 11-5 describes the fields of the CWMP Management window.Table 11-5 Field descriptionsField DescriptionEnable Check this box to Enable CWMP management.ACS URL Enter the URL of the ACS.ACS User Name Enter the username of the ACS.ACS Password Enter the password for the ACS.Inform Message Usage Select Enable to have the device information sent to the ACS. Select Disable to not have the information sent to the ACS.Inform Message Interval (s) Enter an interval in seconds for sending inform messages.Connection Request Username Enter the username used to authenticate an ACS making a connection request to the device.Connection Request Password Enter the password for the connection request of the ACS to the device.
............................................................................................................................................................................................................................................................Connection TestUtilities11-10 3EQ-10280-AAAA-TCZZAEdition 01 February 2011............................................................................................................................................................................................................................................................Connection TestThe Connection Test window enables you to test the connectivity with other network devices.Select Connection Test in the Utilities menu to access the Connection Test window; see Figure 11-7.Figure 11-7 Connection Test windowTable 11-6 describes the fields of the Connection Test window.Table 11-6 Field descriptionsCPE Manufacturer (read-only) The manufacturer of the device.CPE OUI (read-only) The OUI of the device.CPE Product Class (read-only) The model of the device.CPE Serial Number (read-only) The serial number of the device.Apply Changes Click to save your changes.Field DescriptionField DescriptionInterface Select an interface to test if the connection is functioning.Host Enter a host IP address to test the connection.Start Click to test the connection.
Utilities802.1x CA Upload............................................................................................................................................................................................................................................................3EQ-10280-AAAA-TCZZAEdition 01 February 2011 11-11............................................................................................................................................................................................................................................................802.1x CA UploadThe 802.1x CA upload window enables you to upload an 802.1x CA certificate. If you have configured a DHCP WAN connection with 802.1x enabled, then you can use this window to upload a CA that is used to authenticate you with your ISP to be granted DHCP service. Select 802.1x CA Upload in the Utilities menu to access the 802.1x CA Upload window; see Figure 11-8.Figure 11-8 802.1x CA Upload windowTable 11-7 describes the fields of the 802.1x CA Upload window.Table 11-7 Field descriptionsRestore Factory DefaultsThe Restore Factory Defaults window enables you to restore the default settings of the CellPipe 7130 RG.Field DescriptionFile Click Browse to select a CA certificate on your computer to upload.Upload Click to upload the selected CA certificate.Index The index number of the CA certificate. A maximum of eight CA certificates are supported.Information The information pertaining to the CA certificate.
............................................................................................................................................................................................................................................................Reboot GatewayUtilities11-12 3EQ-10280-AAAA-TCZZAEdition 01 February 2011............................................................................................................................................................................................................................................................CAUTIONRestoring the factory default settings will replace your current configuration.Router IP or password changes will also be reset to the default.Select Restore Factory Defaults in the Utilities menu to access the Restore Factory Defaults window; see Figure 11-9.Figure 11-9 Restore Factory Defaults windowClick Restore Defaults to restore the CellPipe 7130 RG to the factory default settings.Reboot GatewayThe Reboot Gateway window enables you to reboot the CellPipe 7130 RG. Note: Rebooting the gateway does not reset your settings.Select Reboot Gateway in the Utilities menu to access the Reboot Gateway window; see Figure 11-10.Figure 11-10 Reboot Gateway windowClick Reboot to restart the CellPipe 7130 RG.
UtilitiesRGAM Management............................................................................................................................................................................................................................................................3EQ-10280-AAAA-TCZZAEdition 01 February 2011 11-13............................................................................................................................................................................................................................................................RGAM ManagementPlease click on Utilities which unfolds the sub-menu. This will show the status of the RGAM. By clicking on the "Access to the RGAM Management interface", the RGAM interface pops up in a different window. Select RGAM Management in the Utilities menu to access the RGAM Management window; see Figure 11-11.Figure 11-11 RGAM Management windowTable 11-8 describes the fields of the RGAM Management window.Table 11-8 Field descriptionsField DescriptionStatus Gives the status if the RGAM is connectedIP IP address which is assigned to the RGAMMAC MAC address which is used by the RGAM"Access to the RGAM management console" opens an new windows which is connected to the web console of the RGAM
............................................................................................................................................................................................................................................................RGAM ManagementUtilities11-14 3EQ-10280-AAAA-TCZZAEdition 01 February 2011............................................................................................................................................................................................................................................................
A-13EQ-10280-AAAA-TCZZAEdition 01 February 2011............................................................................................................................................................................................................................................................A TroubleshootingOverviewThis section identifies common problems that can arise during the use of the CellPipe 7130 RG and offers solutions. Most issues are identified by the LEDs on the front panel of the CellPipe 7130 RG.Troubleshooting TableSymptom Possible cause SolutionPower LED does not come on after power is switched on.Outlet, power cord, or power adapter might be defective.•Check the outlet by plugging in another electronic device.•Call the customer service number or return the device to the vendor.VDSL Link LED flashes slowly after connection is established then it quickly stats to flash slowly again.The DSL port on the gateway or the cable might be defective. •Switch the power off and then switch the power on.•Verify that the cable is connected properly to the VDSL wall line and the DSL connector on the CellPipe 7130 RG.LAN LED does not come on after connection is established.The LAN port on the CellPipe7130 RG, the network interfaceon the computer, or a networkcable may be defective or not connected.•Verify that the power of CellPipe 7130 RG and computer are switched on.•Ensure that the cable is plugged into the CellPipe 7130 RG and the device.•Check the network adapter or the cable connections for defects.
............................................................................................................................................................................................................................................................OverviewTroubleshootingA-2 3EQ-10280-AAAA-TCZZAEdition 01 February 2011............................................................................................................................................................................................................................................................Message LED is flashing.A firmware upgrade is in progress.•Verify that a firmware upgrade is in progress.•Wait until the firmware upgrade is finished.Intenet LED is off. Your CellPipe 7130 RG is unable to connect to the Internet or CellPipe 7130 RG is not power on.•Verify that your CellPipe 7130 RG has configured WAN connections properly.•Verify that the power is switched on.Symptom Possible cause Solution
B-13EQ-10280-AAAA-TCZZAEdition 01 February 2011............................................................................................................................................................................................................................................................B TCP/IP configurationOverviewThe following procedures provide TCP/IP configuration instructions for all supported operating systems.Windows 71. Open Network and Internet from the Control Panel.2. Open Network and Sharing Center from the Network and Internet.3. Right-click Local Area Connection from Network and Sharing Center.4. Under the General tab, select Internet Protocol (TCP/IPv4), and click Properties.5. Select the Obtain an IP address automatically radio button.6. Select the Obtain DNS server address automatically radio button.7. Click OK to save the settings.........................................................................................................................................................END OF STEPSWindows Vista1. Open Network and sharing Center from the Control Panel.2. Open Manage network connections from the Network and sharing Center.3. Right-click Ethernet connection and select Properties.4. Under the General tab, select Internet Protocol (TCP/IPv4), and click Properties.5. Select the Obtain an IP address automatically radio button.6. Select the Obtain DNS server address automatically radio button.7. Click OK to save the settings.........................................................................................................................................................END OF STEPSWindows XP1. Open Network Connections from the Control Panel.2. Right-click Ethernet connection and select Properties.
............................................................................................................................................................................................................................................................OverviewTCP/IP configurationB-2 3EQ-10280-AAAA-TCZZAEdition 01 February 2011............................................................................................................................................................................................................................................................3. Under the General tab, select Internet Protocol (TCP/IP), and click Properties. The Internet Protocol (TCP/IP) properties window appears.4. Select the Obtain an IP address automatically radio button.5. Select the Obtain DNS server address automatically radio button.6. Click OK to save the settings.........................................................................................................................................................END OF STEPSWindows Me/2000/98/951. Open Network and Dialing Connections from the Control Panel.2. Right click the Ethernet connection icon and select Properties. 3. Select Internet Protocol (TCP/IP) component, and click Properties. The Internet Protocol (TCP/IP) properties window appears.4. Select the Obtain an IP address automatically radio button.5. Select the Obtain DNS server address automatically radio button.6. Click OK to save the settings.........................................................................................................................................................END OF STEPSWindows NT1. Open Network from the Control Panel.2. From the Protocol tab, select the Internet Protocol (TCP/IP) component, and click the Properties button.3. From the IP Address tab, select the Obtain an IP address automatically radio button.4. From the DNS tab, verify that no DNS server is defined in the DNS Service Search Order box and no suffix is defined in the Domain Suffix Search Order box.........................................................................................................................................................END OF STEPSMac OS1. Open System Preferences from the Panel.2. Choose Network from Internet & Network.3. Make sure the window is unlocked. If it is locked, click the lock to make changes and enter the password for authentication.4. From the TCP/IP tab, choose the Using DHCP on Configure IPv4 field.5. Click on the Apply Now button to obtain an IP address from the DHCP server.........................................................................................................................................................END OF STEPS
C-13EQ-10280-AAAA-TCZZAEdition 01 February 2011............................................................................................................................................................................................................................................................C Product conformanceOverviewThis section lists the product conformance requirements for the EU and the FCC conformance requirements.EU declaration of conformityThis device complies with the essential requirements of the R&TTE Directive 1999/5/EC. The following test methods have been applied in order to prove presumption of conformity with the essential requirements of the R&TTE Directive 1999/5/EC:•IEC 60950-1: 2006 + A11: 2009Safety of Information Technology Equipment•EN50385 : (2002-08)Product standard to demonstrate the compliance of radio base stations and fixed terminal stations for wireless telecommunication systems with the basic restrictions or the reference levels related to human exposure to radio frequency electromagnetic fields (110MHz - 40 GHz) - General public•EN 300 328 V1.7.1: (2006-10)Electromagnetic compatibility and Radio spectrum Matters (ERM); Wideband Transmission systems; Data transmission equipment operating in the 2,4 GHz ISM band and using spread spectrum modulation techniques; Harmonized EN covering essential requirements under article 3.2 of the R&TTE Directive•EN 301 489-1 V1.8.1: (2008-04)Electromagnetic compatibility and Radio Spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 1: Common technical requirements•EN 301 489-17 V2.1.1 (2009-05)Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment; Part 17: Specific conditions for Broadband Data Transmission Systems
............................................................................................................................................................................................................................................................EU declaration of conformityProduct conformanceC-2 3EQ-10280-AAAA-TCZZAEdition 01 February 2011............................................................................................................................................................................................................................................................This device is a 2.4 GHz wideband transmission system (transceiver), intended for use in all EU member states and EFTA countries, except in France and Italy where restrictive use applies. In Italy the end-user should apply for a license at the national spectrum authorities in order to obtain authorization to use the device for setting up outdoor radio links and/or for supplying public access to telecommunications and/or network services. This device may not be used for setting up outdoor radio links in France and in some areas the RF output power may be limited to 10 mW EIRP in the frequency range of 2454 – 2483.5 MHz. For detailed information the end-user should contact the national spectrum authority in France.
Product conformanceFCC 15B statement............................................................................................................................................................................................................................................................3EQ-10280-AAAA-TCZZAEdition 01 February 2011 C-3............................................................................................................................................................................................................................................................FCC 15B statementFederal Communication Commission Interference StatementThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:•Reorient or relocate the receiving antenna.•Increase the separation between the equipment and receiver.•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.•Consult the dealer or an experienced radio/TV technician for help.FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.IMPORTANT NOTE:FCC Radiation Exposure StatementThis equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.The availability of some specific channels and/or operational frequency bands are country dependent and are firmware programmed at the factory to match the intended destination. The firmware setting is not accessible by the end user.
............................................................................................................................................................................................................................................................FCC Part 68 StatementProduct conformanceC-4 3EQ-10280-AAAA-TCZZAEdition 01 February 2011............................................................................................................................................................................................................................................................FCC Part 68 StatementThis equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On the base unit of this equipment is a label that contains, among other information, a product identifier in the format US: GEMDL01BWVVDB101N. If requested, this number must be provided to the telephone company.Applicable connector jack Universal Service Order Codes ("USOC") for the Equipment is RJ11C and RJ45.A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant telephone cord and modular plug is provided with this product. It is designed to be connected to a compatible modular jack that is also compliant. See installation instructions for details.The REN is used to determine the number of devices that may be connected to a telephone line. Excessive RENs on a telephone line may result in the devices not ringing in response to an incoming call. In most but not all areas, the sum of RENs should not exceed five (5.0). To be certain of the number of devices that may be connected to a line, as determined by the total RENs, contact the local telephone company. For products approved after July 23, 2001, the REN for this product is part of the product identifier that has the format US: GEMDL01BWVVDB101N. The digits represented by 01 are the REN without a decimal point (e.g., 03 is a REN of 0.3).If this CellPipe 7130 RG 6Vz.A2131 causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. But if advance notice isn't practical, the telephone company will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary.The telephone company may make changes in its facilities, equipment, operations or procedures that could affect the operation of the equipment. If this happens the telephone company will provide advance notice in order for you to make necessary modifications to maintain uninterrupted service.If trouble is experienced with this Alcatel-Lucent, for repair or warranty information, please contact 600-700 Mountain Avenue Murry Hill, NJ 07974 or Tel no.: 1-908-508-8080 If the equipment is causing harm to the telephone network, the telephone company may request that you disconnect the equipment until the problem is resolved.
Product conformanceIndustry Canada statement............................................................................................................................................................................................................................................................3EQ-10280-AAAA-TCZZAEdition 01 February 2011 C-5............................................................................................................................................................................................................................................................Connection to party line service is subject to state tariffs. Contact the state public utility commission, public service commission or corporation commission for information.If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this equipment does not disable your alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone company or a qualified installer.WHEN PROGRAMMING EMERGENCY NUMBERS AND(OR) MAKING TEST CALLS TO EMERGENCY NUMBERS:1) Remain on the line and briefly explain to the dispatcher the reason for the call.2) Perform such activities in the off-peak hours, such as early morning or late evenings.Industry Canada statementThis device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.IMPORTANT NOTE:Radiation Exposure StatementThis equipment complies with Canada radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
............................................................................................................................................................................................................................................................IC TELECOMProduct conformanceC-6 3EQ-10280-AAAA-TCZZAEdition 01 February 2011............................................................................................................................................................................................................................................................This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.IC TELECOM''NOTICE: This equipment meets the applicable Industry Canada Terminal Equipment Technical Specifications. This is confirmed by the registration number. The abbreviation, IC, before the registration number signifies that registration was performed based on a Declaration of Conformity indicating that Industry Canada technical specifications were met. It does not imply that Industry Canada approved the equipment."''NOTICE: The Ringer Equivalence Number (REN) for this terminal equipment is 01. The REN assigned to each terminal equipment provides an indication of the maximum number of terminals allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed five.''"CAUTION: To reduce the risk of fire, use only No. 26 AWG or larger (e.g., 24 AWG) UL Listed or CSA Certified Telecommunication Line Cord"
Product conformanceIC TELECOM............................................................................................................................................................................................................................................................3EQ-10280-AAAA-TCZZAEdition 01 February 2011 C-7............................................................................................................................................................................................................................................................"IMPORTANT SAFETY INSTRUCTIONS - When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following:•Do not use this product near water for example, near a bathtub, washbowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool.•Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning.•Do not use the telephone to report a gas leak in the vicinity of the leak.•Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a fire. They may explode. Check with local codes for possible special disposal instructions.SAVE THESE INSTRUCTIONS"
............................................................................................................................................................................................................................................................IC TELECOMProduct conformanceC-8 3EQ-10280-AAAA-TCZZAEdition 01 February 2011............................................................................................................................................................................................................................................................
GL-13EQ-10280-AAAA-TCZZAEdition 01 February 2011............................................................................................................................................................................................................................................................GlossaryNumerics10/100Base-TThe most widely used standard for Ethernet over twisted pair or copper-based computer networking. Runs at 10 Mb/s, 100 Mb/s, and 1000 Mb/s (1 Gb/s) respectively.802.11b/g/nA family of specifications for wireless local area networks (WLANs). They use the Ethernet protocol and CSMA/CA (carrier sense multiple access with collision avoidance) for path sharing.802.1 Q/PThe standard that allows multiple bridged networks to transparently share the same physical network link without leakage of information between networks.802.1xAn authentication standard for clients connecting to an IEEE 802 network such as Ethernet (access) networks and 802.11 (public) wireless LANs.AACSAuto-Configuration ServerALGApplication-Level GatewayAPAccess PointAPIApplication Programming InterfaceCCDVTCell Delay Variation ToleranceCHAPChallenge-Handshake Authentication ProtocolCodecA device or computer program capable of encoding and/or decoding a digital data stream or signal.CoSClass of Service
............................................................................................................................................................................................................................................................GlossaryGL-2 3EQ-10280-AAAA-TCZZAEdition 01 February 2011............................................................................................................................................................................................................................................................CPECustomer Premises EquipmentCWMPCPE WAN Management ProtocolDDDNSDynamic Domain Name SystemDHCPDynamic Host Configuration ProtocolDMZDemilitarized ZoneDNSDomain Name SystemDSCPDifferentiated Services Code PointDSLDigital Subscriber LineDTIMDelivery Traffic Indication MessageDynamic RoutingThe capability of a system, through which routes are characterised by their destination, to alter the path that the route takes through the system in response to a change in conditions.EEthernetA family of frame-based computer networking technologies for local area networks (LANs).FFirewallAn integrated collection of security measures designed to prevent unauthorized electronic access to a networked computer system.FQDNFullQualified Domain NameFTNForward to NumberGGatewayA network node equipped for interfacing with another network that uses different protocols.
GlossaryGL-33EQ-10280-AAAA-TCZZAEdition 01 February 2011........................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................HHTMLHyper Text Markup LanguageIIGMPInternet Group Management ProtocolIPInternet ProtocolIPSecInternet Protocol SecurityISPInternet Service ProviderKkb/sKilobit per second; a data rate unit.LL2TPLayer 2 tunneling protocol; a tunneling protocol used to support virtual private networks (VPNs).LANLocal Area NetworkMMACMedia Access ControlMbMegabit; a unit of information commonly used to express the rate data is transferred.MTUMaximum Transmission UnitNNATNetwork Address TranslationNetmaskThe designated IP address routing prefix for a network of computers and devices.NICNetwork Interface ControllerNTPNetwork Time Protocol
............................................................................................................................................................................................................................................................GlossaryGL-4 3EQ-10280-AAAA-TCZZAEdition 01 February 2011............................................................................................................................................................................................................................................................OOUIOrganizationally Unique IdentifierOutbound Proxy ServerThe server responsible for handling calls made behind the NAT device by examining and translating the IP addresses.PPAPPassword Authentication ProtocolPingA computer network tool used to test whether a particular host is reachable across an IP network.PPPoEPoint-to-Point Protocol over EthernetPPTPPoint-to-Point Tunneling ProtocolPSKPre-Shared KeyQQoSQuality of ServiceRRJ-11A physical interface often used for terminating telephone wires.RJ-45Most regularly used as an Ethernet connector. RJ-45 connectors are typically used to terminate twisted pair cable.RTPReal-time Transport Protocol; handles voice data transfer making VoIP call using SIP.SSSHSecure ShellSIPSession Initiation Protocol; an application layer control protocol that handles the setting up, altering and tearing down of voice and multimedia sessions over the Internet.SSIDService Set Identifier
GlossaryGL-53EQ-10280-AAAA-TCZZAEdition 01 February 2011........................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................SubnetSee Netmask.TTCPTransmission Control ProtocolTel ne tTelecommunications network; a network protocol used on the Internet or local area network (LAN) connections.TFTPTrivial File Transfer ProtocolTo SType of ServiceUUDPUser Datagram ProtocolUPnPUniversal Plug and PlayURLUniform Resource LocatorVVCIVirtual Channel IdentifierVDSLVery High Bitrate Digital Subscriber LineVLANVirtual Local Area NetworkVoIPVoice over Internet ProtocolVPIVirtual Path IdentifierWWANWide Area NetworkWDSWireless Distribution SystemWEPWired Equivalent Privacy
............................................................................................................................................................................................................................................................GlossaryGL-6 3EQ-10280-AAAA-TCZZAEdition 01 February 2011............................................................................................................................................................................................................................................................WiFiWireless networking compatibilityWLANWireless Local Area NetworkWPAWiFi Protected AccessWPSWiFi Protected Setup

Navigation menu