GemTek Technology M930112AG Tablet PC with 802.11 a/b/g and Bluetooth User Manual

Gemtek Technology Co., Ltd. Tablet PC with 802.11 a/b/g and Bluetooth Users Manual

UserManual.wiki >

GemTek Technology >

M930112AG User Manual >

Contents

1. DoC
2. Users Manual

Users Manual

English 1Product Safety InformationMotion Tablet PCs and accessories are designed to optimize safety, minimize strain,and withstand the rigors of portability. However, to further reduce the risk ofpersonal injury or damage to the unit, certain precautions shouldbe observed. Basic Personal Safety Precautions■ Do not attempt to service the Tablet PC nor its components yourself. Performonly those service installations for which Motion provides special instructions,for example, swapping the battery, changing memory modules. See the Motionweb site at www.motioncomputing.com for a list of serviceable accessories foryour Tablet PC.■ To avoid personal injury from electric shock or fire:• Completely power down the Tablet PC when replacing memory modules,cleaning the Tablet PC, its components, or chassis, or performingoperations requiring similar steps. To do this, first turn the power off atthe power switch, remove the battery, then disconnect the AC adapterfrom the electrical outlet or from any other type of external power source,such as an external battery• Do not operate the Tablet PC near water, for example, near a bathtub,kitchen sink or laundry tub, in a wet basement, by a swimming pool, or inthe rain. The cases, portfolios, and other accessories currently offered byMotion are not designed to be water resistant nor water tight. Visit theMotion website to see the most current list of accessories.• Do not connect or disconnect any cables or perform maintenance orreconfiguration of this product during an electrical storm.• Avoid using the wired modem or LAN during an electrical storm, as aremote risk of electric shock from lightning exists.• Do not push foreign objects into air vents or other openings of the TabletPC or accessories, such as the PCA card slots or the optical disk drivebays. Doing so can short out interior components and may cause fire orelectric shock.• When installing memory modules, ground yourself by touching agrounded conductive surface, such as a device with a grounded plug.Avoid touching the pins and leads on the memory module or internalcircuitry of the Tablet PC.■ If the Motion battery pack leaks and the fluid get in your eyes, do not rub them.Instead, rinse your eyes with clean running water and immediately seek medicalattention. Otherwise, eye injury may result.■ If acid leaking from the battery pack contacts your skin or clothing, immediatelywash it away with running water. Otherwise, skin inflammation can occur.

English2 Set Up Precautions■ When setting up the Tablet PC in the Motion FlexDock, Desktop Stand, orHardtop Keyboard, place it on a level surface so it does not fall over and damagethe unit, docking station, keyboard, connectors, or other components.■ When you move the Tablet PC between environments with very differenthumidity and/or temperature ranges, allow sufficient time to adjust to the newhumidity or temperature.■ Do not drop the Tablet PC or subject it to other mechanical shocks.■ Do not apply heavy pressure to the Tablet PC or subject it to strong impact.Excessive pressure or impact can cause damage to Tablet PC components orotherwise cause malfunctions. Tablet PC Precautions■ Do not attempt to service the Tablet PC yourself, disassemble nor modify it norits components. You may damage the unit or its components.■ Operate the Tablet PC at the recommended temperature range of +5oC to +35oC(+41oF to +95oF). Store it at a temperature of -20oC to +60oC (+4oF to +140oF)■ Certain environments may contain particles or debris that can adhere to theTablet PC display or to the Tablet PC pen tip. To avoid damaging the display,clean it frequently with the cleaning cloth provided or with a soft cloth. You mayspray a window-type cleaner or apply water to the cloth, but do not spray liquidsdirectly on the display.■ Change pen tips regularly, especially if you work in an environment that containsparticles or debris. Dropping the pen onto a rough surface may damage the pentip or embed particles in it that can damage the Tablet PC display. Forinstructions about changing the pen tips, see Chapter 4 of the Motion Tablet PCUser Guide found on the Tablet PC or go to the Motion website atwww.motioncomputing.com to download the latest version of this Guide.■ Store the pen in the pen bay of the Tablet PC. Carrying it in a pocket, toolbox, orsimilar receptacle that contains particles or debris may damage the pen tip orembed particles in it that can damage the Tablet PC display. Cabling and Power Cord Precautions■ Power cord sets for use in other countries must meet the requirements of thatcountry. Use the appropriate AC adapter and power cord for your locale. Forinformation about power cord set requirements, contact the Motion Reseller fromwhom you purchased the product, or contact Motion Computing if you purchasedthe product from us.■ If no power cord was provided for your Tablet PC or for an accessory, purchase apower cord that is approved for use in your country and that matches the requiredvoltage / amperage rating of the Tablet PC.

English 3■ If you use an extension cord with your AC adapter, ensure that the total ampererating of the products plugged into the extension cord does not exceed theampere rating of the extension cable.■ When using your power cord, make sure to position it around objects so it willnot be cut or punctured. Power Adapter Precautions■ Use only the AC adapter and power cord approved for this Tablet PC or TabletPC accessory. Use of another type of AC adapter may risk fire or explosion.■ Place the AC adapter in a ventilated area, such as on a desktop or the floor, whenyou use it to run the Tablet PC or to charge the battery. Do not cover the ACadapter with papers or other items that will reduce cooling; also, do not use theAC adapter while it is inside a carrying case.■ Be sure that nothing rests on the AC adapter's power cable and that the cable isnot located where it can be tripped over or stepped on.■ When using your power cord, make sure to position it around objects so it willnot be cut or punctured.■ Disconnect power cords and cables by grasping the connector, not by pulling onthe cable itself. As you pull out the connector, keep it evenly aligned to avoidbending any connector pins. Before you connect a cable, make sure bothconnectors are correctly aligned. Battery Pack Warnings and Precautions■ The Tablet PC contains an internal lithium ion (Li-ion) battery pack. Replace theinternal battery pack only with a Motion battery or a Motion-approved equivalentto avoid the risk of fire or explosion resulting in personal injury.■ If you use an external battery pack to power your Tablet PC, be sure you use onlya Motion-recommended third-party product, which has been tested with theMotion Tablet PC, Using a non-Motion-recommended external battery maycause the Tablet PC to overheat, emit smoke, burst and/or ignite and causepersonal injury or damage to the unit.■ Do not use the battery pack in combination with other types of battery packs(such as dry-cell battery packs) or battery packs with different capacities orbrands. This can result in it being over discharged during use or overchargedduring recharging, possibly leading it to leak acid, overheat, emit smoke, burstand/or ignite.■ Do not dispose of batteries in a fire. They may explode. Dispose of used batteriesaccording to the manufacturer's instructions. The label on the battery lists themanufacturer’s name. See the section “Battery Pack Disposal” in the Guide formore information about battery disposal.

English4■ Do not use nor leave the battery pack near a heat source. Heat can melt theinsulation and damage other safety features, possibly leading it to leak acid,overheat, emit smoke, burst and/or ignite.■ Do not immerse the battery pack in water nor allow it to get wet. Its protectivefeatures can be damaged, it can be charged with extremely high current andvoltage, abnormal chemical reactions may occur, possibly leading it to leak acid,overheat, emit smoke, burst and/or ignite.■ Do not disassemble or modify the battery pack. If disassembled, the battery packcould leak acid, overheat, emit smoke, burst and/or ignite.■ Do not connect the positive (+) and negative (-) terminals with a metal objectsuch as wire. Short-circuiting may occur leading the battery pack to leak acid,overheat, emit smoke, burst and/or ignite.■ Do not pierce the battery pack with a sharp object, strike it with a hammer, stepon it, or throw it. These actions could damage or deform it, internal short-circuiting can occur, possibly leading it to leak acid, overheat, emit smoke, burstand/or ignite.■ Do not use an apparently deformed or damaged battery pack, which may leakacid, overheat, emit smoke, burst and/or ignite.■ Do not directly solder the battery pack. Heat can melt the insulation and damageother safety features, possibly leading it to leak acid, overheat, emit smoke, burstand/or ignite.■ Store the battery pack in a location where children cannot reach it. Make surechildren do not remove the battery pack from the Tablet PC or charger.■ If the battery pack leaks, gives off a bad odor, generates heat, becomes discoloredor deformed, or in any way appears abnormal during use, recharging or storage,immediately remove it from the Tablet PC or charger and stop using it, If this isdiscovered when you first use the battery, return it to your Motion reseller or toMotion Computing, if you bought it directly from us.■ Do not transport the lithium ion batteries used in your Tablet PC in checkedbaggage. You may take up to two spare batteries in carry-on luggage in additionto the one in your Tablet PC. Transporting batteries in checked baggage ortransporting more than two spare batteries in carry-on baggage violatestransportation law. Remember to remove batteries from the battery chargerbefore transporting it in carry-on or checked baggage.■ ■ Battery Precautions (Carbon and Alkaline)■ Keep batteries out of reach of children.■ Do not mix old and new batteries of different types (for example, carbon andalkaline batteries).■ Always remove old, weak, or worn-out batteries promptly and recycle or disposeof them according to the manufacturer’s directions.■ If a battery leaks, remove all batteries and dispose of them according to themanufacturer’s directions. Before replacing the batteries, clean the battery

English 5compartment in accordance with the battery manufacturer’s recommendations. Ifbattery fluid contacts your skin or clothes, immediately flush them with water.■ Battery Warnings (Carbon and Alkaline)■ Battery electrolytes are corrosive, CAN CAUSE DAMAGE TO THE EYESAND SKIN, AND MAY BE TOXIC IF SWALLOWED. Avoid the followingactions that can cause the sudden release of battery electrolytes:■ Do not open, puncture, or mutilate the batteries.■ Do not heat the batteries.■ Do not burn the batteries in a fire to dispose of them. Battery Charger Precautions■ Read the documentation supplied with the battery charger. This providesadditional information about charging and precautions for use.■ Use only a Motion battery charger to recharge the batteries. It is specificallydesigned for that purpose. Charging with a non-Motion battery charger couldresult in extremely high current and voltage, abnormal chemical reactions mayoccur, possibly leading it to leak acid, overheat, emit smoke, burst and/or ignite.■ Battery charging temperature: The ambient temperature of the battery beingcharged should from 0º C to +40º C (+32º F to +104º F). Charging the batteryoutside this range may harm battery performance or reduce battery life.■ Do not recharge the battery pack near fire or in extremely hot weather. Hottemperatures can inhibit recharging or can damage its built-in protective features.Heat can possibly lead to acid leakage, overheating, smoking, bursting and/origniting.■ If you transport the battery charger in checked baggage, be sure to remove thebatteries from the charger before packing it. Battery Pack Disposal■ Dispose of the lithium ion battery packs only at approved disposal sites. Tolocate an appropriate site, contact the solid waste disposal officials where youlive or look for a rechargeable battery recycling website that lists disposallocations near you.■ Do not dispose of battery packs in a fire, throw them in a trash receptacle, putthem in a recycling bin not intended for their disposal, or otherwise discard themin a manner that may result in their being hazardous to the environment.

English6 Travel Precautions■ For information about transporting batteries, see the section “Battery Warningsand Precautions” in this guide.■ When traveling, do not store the Tablet PC in an overhead compartment or otherarea where it could slide around, nor check it in your baggage.■ Do not put the Tablet PC through a metal detector. You can safely put it throughan X-ray security machine without harming any components.■ Be sure to charge the battery before you hand check the Tablet PC. You may beasked to turn the Tablet PC on at a baggage check point. Internal Modem Precautions■ The modem cable you connect to your Tablet PC should have a minimum wiresize of 26 AWG (American wire gauge) and an UL-compliant RJ-11 modularplug.■ Do not plug a modem connector (RJ-11) into a network connection (RJ-45). Thismay damage the connector.■ See the section “Telecommunication Devices/Modem Approvals” in this Guidefor important information about modem use. Accessory Precautions■ Please read the instructions packaged with your accessories carefully beforesetting up or operating them. The Motion accessory you purchase may includedocumentation about safety, precautions, and warnings needed to set up oroperate the accessory. This accessory documentation provides specificinformation about functionality, usage limitations, user serviceability, batterydisposal, handling precautions, or electrostatic discharge, etc, for the product.■ The cases, portfolios, and other accessories currently offered by Motion are notdesigned to be water resistant nor water tight. Visit the Motion website to see themost current list of accessories. Motion-Recommended Third-PartyAccessories■ Use only Motion-recommended third-party accessories with a Motion Tablet PC.These devices have been tested by Motion Computing for use with a MotionTablet PC.■ If you choose to use a non-Motion-recommended third-party accessory it is atyour own risk and may damage the Tablet PC or the accessory device.

English7 Comfort and HealthHEALTH WARNING: Keyboard use or use of a pointing device may be linked toserious injuries or disorders. For further information, visit the My Clinic website atwww.myoclinic.com.You may help prevent the occasional discomfort in your hands, arms, shoulders,neck, and other parts of your body by:■ Taking frequent breaks to stretch and change your working position.■ Resting your hands and wrists frequently so they have time to recover fromrepetitive movements. Use a wrist pad.■ Using the touch pad on a keyboard or the Tablet PC pen, which change the wayyou use your hands and wrists; this provides a break from the keyboard keys ormouse.If these symptoms persist or continue to occur and include pain, throbbing, aching,tingling, numbness, burning sensations, or stiffness, DO NOT IGNORE THESEWARNING SIGNS. PROMPTLY SEE A QUALIFIED HEALTHPROFESSIONAL.

English8Regulatory and Safety ComplianceThe following sections describe regulatory and safety compliance by country and byregion.NOTE: To determine what regulatory and safety marks apply to a specific product,component, or accessory, check the product label affixed to the product or its component.Federal Communications Commission Notice(United States)Electromagnetic Interference (EMI) is any electromagnetic disturbancethat interrupts, obstructs, or otherwise degrades or limits the effectiveperformance of electronics or electrical equipment. These emissions canpotentially disrupt, degrade, or otherwise interfere with authorizedelectronic emissions, which may include television, AM/FM broadcasts,cellular services, radar, air-traffic control, and pagers.The FCC Rules and Regulations have established Radio Frequency (RF) emissionlimits to provide an interference-free RF spectrum. Many electronic devices,including computers, generate RF energy incidental to their intended function andare, therefore, covered by these rules.Your Motion Tablet PC system, Motion FlexDock, Hardtop Keyboard, and allaccessories have been designed and found to meet the regulatory agency limits forElectromagnetic Compatibility (EMC). EMC is the ability of electronic devices,including computers, to function properly together in the electronic environment.However, there is no guarantee that in a specific installation it will not causeinterference. Should this equipment cause harmful interference to radio or televisionreception, which can be determined by turning the equipment off and on, you areencouraged to try to correct the interference by one or more of the followingmeasures:■ Reorient the receiving antenna.■ Relocate the Tablet PC and the receiver.■ Separate the Tablet PC and the receiver.■ Plug the Tablet PC and receiver into different circuits.You may also need to contact a radio/television technician for assistance.

English10■ Consult the dealer or an experienced radio/television technicianfor help

English 11The following information is provided on the device or devices covered in thisdocument in compliance with FCC regulations:■ Model numbers: T001 (Motion M1200 Tablet PC), T002 (Motion M1300 TabletPC), T003 (Motion M1400 Tablet PC)■ Company name: Motion Computing, Inc.■ 9433 Bee Caves Road, Building 1, Suite 250■ Austin, Texas 78733■ 512-637-1100Intentional Emitter per FCC Part 15Embedded in your Tablet PC are various Radio Frequency (RF) wirelesscommunication devices. It may contain one or more Radio type devices that operatein the 450-1550 KHz band, as well as devices that operate in the 2.4 or 5.4 GHzBand. All Radio type devices embedded in your Tablet PC have met all thequalifications for use under FCC regulations and guidelines.This equipment complies with FCC Radio Frequency Electromagnetic Signal (RF)exposure limits set forth for an uncontrolled environment of portable transmission.This device complies with FCC RF Exposure limits set forth for an uncontrolledenvironment, under 47 CFR 2.1093 paragraph (d)(2).This transmitter must not be co-located or operating in conjunction with any other antennaantenna or transmitter.Operation of this wireless communication device is subject to the following twoconditions:■ This device may not cause harmful interference■ This device must accept any interference received, including interference thatmay cause undesired operation.WARNING: Do not attempt to service the wireless communication device built intothe Tablet PC yourself. Such action may void the warranty on the Tablet PC. Contactyour Motion Reseller or Motion Computing for information about servicing yourwireless communication device.NOTE: The Radio Frequency (RF) emitter installed in your Tablet PC must not be located oroperated in conjunction with any other antenna or transmitter.ModificationsThe FCC requires that you be notified that any changes or modifications made tothis device that are not expressly approved by Motion Computing, Inc. may voidyour authority to operate the equipment.CablesConnections to this Tablet PC must be made only with shielded cables. This reduces

English12possible interference with radio communications and complies with FCC Rules andRegulations for this EMC classification.Airline Travel NoticeThe FAA requires that you suspend wireless operations before boardingan airplane. These include both internal and external wireless devices.Internal wireless connections are indicated by the wireless LED on theTablet PC front panel (identified by the wireless icon shown here). If theLED is ON or blinking, the wireless connection is enabled. Externalwireless devices may be installed in the PCMCIA Card slot or attached tothe Tablet PC and must also be disabled. For information about disabling thesedevices, see IMPORTANT below.IMPORTANT: To disable internal Tablet PC wireless operations, open the Motion Dashboardby pressing Hot Key #1 and under Wireless, disable any wireless connections (802.11 orinternal Bluetooth wireless radios). When internal Tablet PC wireless operations are disabled,the wireless LED on the Tablet PC front panel is OFF.To disable external wireless devices installed in the Tablet PC PCMCIA Card slot or attachedto the Tablet PC, eject the card or unplug the external device. To disable external devices viathe software, see the instructions that came with the device or contact the devicemanufacturer.

English 13IC Notice (Canada Only)Unintentional Emitter per ICES-003Motion Computing Tablet PCs are classifiedby the Industry Canada (IC) Interference-Causing Equipment Standard #3 (ICES-003) as Class B digital devices. Thisclassification is located on the label on the bottom of your Tablet PC. Look for astatement on the label similar to the following: Canada ICES-003, Class/Classe B.This Class B (or Class A, if so indicated on the registration label) digital apparatusmeets the requirements of the Canadian Interference-Causing EquipmentRegulations.Cet appareil numérique de la Classe B (ou Classe A, si ainsi indiqué sur l’étiquetted’enregistration) respecte toutes les exigences du Règlement sur le MatérielBrouilleur du Canada.Intentional Emitter per RSS 210Embedded in your Tablet PC are various Radio Frequency (RF) wirelesscommunication devices. It may contain one or more Radio type devices that operatein the 450-1550 KHz band, as well as devices that operate in the 2.4 or 5.4 GHzBand. All Radio type devices embedded in your Tablet PC comply with RSS 210 ofIndustry Canada. Operation is subject to the following two conditions: (1) thisdevice may not cause interference, and (2) this device must accept any interference,including interference that may cause undesired operation of this device.L’utilisation de ce dispositif est autorisée seulement aux conditions suivantes: (1) ilne doit pas produire de brouillage et (2) l’utilsateur du dispositif doit éntre prét aaccepter tout brouillage radioélectrique recu, meme si ce brouillage est susceptiblede compromettre le fonctionnement du dispositif.The term “IC” before the equipment certification number only signifies that theIndustry Canada technical specifications were met.This equipment complies with Industry Canada Radio Frequency ElectromagneticSignal (RF) exposure limits set forth for an uncontrolled environment of portabletransmission.

English14Conformité Européne (CE) (European Union)Unintentional EmitterThe (Conformité Européne) symbol found on the Tablet PC indicatescompliance to the EMC Directive and the Low Voltage Directive of theEuropean Union. This means that the Tablet PC meets the followingtechnical standards:■ EN 55011 (CISPR 11) — Limits and Methods of Measurement of RadioInterference Characteristics of Industrial, Scientific, And Medical (ISM) RadioFrequency Equipment■ EN 55022 (CISPR22) — Limits and Methods of Measurement of RadioInterference Characteristics of Information Technology Equipment■ EN 55024 (IEC 61000 4-2, 4-3, 4-3, 4-5, 4-6, 4-8, 4-11) — InformationTechnology Equipment-Immunity Characteristics - Limits and Methods ofMeasurement■ EN 61000 3-2 (IEC 61000 3-2) — Electromagnetic compatibility (EMC) - Part 3:Limits - Section 2: Limitations for harmonic current emissions (Equipment inputcurrent up to and including 16 A per phase)■ EN 61000 3-3 (IEC 61000 3-3) — Electromagnetic compatibility (EMC) - Part 3:Limits - Section 3: Limitations of voltage fluctuations and flicker in low-voltagesupply systems for equipment with rated current up to and including 16 A■ EN60950 (IEC 60950 3rd Ed; 1999; 2000) — Safety of Information TechnologyEquipmentIntentional EmitterThe CE mark shown here is a device ID that means theproduct complies with the essential requirements of theR&TTE Directive 1999/5/EC with essential test suites.Embedded in your Tablet PC are various Radio Frequency (RF) wirelesscommunication devices. It may contain one or more Radio type devices that operatein the 450-1550 KHz band, as well as devices that operate in the 2.4 or 5.4 GHzBand. All Radio type devices embedded in your Tablet PC comply with standards:■ EN60950 (IEC 60950 3rd Ed; 1999; 2000) — Safety of Information TechnologyEquipment■ ETS 300 328 — Technical requirements for radio equipment■ ETS 300 826 — General EMC requirements for radio equipmentBelegië/BelgiqueFor outdoor usage only, channels 10 (2457 MHz) and 11 (2462 MHz) are allowed.For private usage outside buildings across public grounds over less than 300 meters,

English 15no special registration with IBPT/BIPT (Belgium Institute for Postal services andTelecommunications) is required. Registration to IBPT/BIPT is required for privateusage outside buildings across public grounds over more than 300 meters. An IBPT/BIPT license is required for public usage outside buildings. For registration andlicense, please contact IBPT/BIPT.Gebruik buiten gebouw alleen op kanalen 10 (2457 MHz) en 11 (2462 MHz). Voorprivé-gebruik buiten gebouw over publieke groud over afstand kleiner dan 300mgeen registratie bij BIPT/IBPT nodig; voor gebruik over afstand groter dan 300m iswel registratie bij BIPT/IBPT nodig. Voor publiek gebruik buiten gebouwen islicentie van BIPT/IBPT verplicht. Voor registratie of licentie kunt u contactopnemen met BIPT.L’utilisation en extérieur est autorisé sur le canal 10 (2457 MHz) et 11 (2462 MHz).Dans le cas d’une utilization privée, à l’extérieur d’un bâtiment, audessus d’unespace public, aucun enregistrement n’est pas nécessaire pour une distance de moinsde 300m. Pour une distance supérieure à 300m un enregistrement auprés de l’IBPTest requisé. Pour une utilisation publique à l’extérieur de bâtiments, une licence del’IBPT est requise. Pour les enregistrements et licences, veuillez contacter l’IBPT.DeutschlandA license is required for outdoor installations. Check with reseller for the procedureto follow.Anmeldung im Outdoor-Bereich notwendig, aber nicht genehmigungspflichtig. Bittemit Händler die Vorgehensweise abstimmen.FranceRestricted frequency band: only channels 10 and 11 (2457 MHz and 2462 MHzrespectively) may be used in France.A license is required for every installation, indoor and outdoor. Please contact ART(L’Autorité de Régulation des Télécommunications) for procedure to follow.Bande de fréquence restreinte: seuls les canaux 10 à 11 (2457 et 2462 MHzrespectivement) doivent être utilisés en France.Toute utilisation, qu’elle soit intérieure ou extérieure, est soumise à autorisation.Vous pouvez contacter L’Autorité de Régulation des Télécommunications(http://www.art-telecom.fr) pour la procédure à suivre.

English16ItaliaA license is required for indoor use. Use with outdoor installations is not allowed.E’necessaria la concessione ministeriale anche per l’uso interno Verificare con irivenditori la procedura da seguire. L’uso per installazione in esterni none’permessa.NederlandA license is required for outdoor installations. Check with reseller for the procedureto follow.Licentie verplicht voor gebruik met buitenatennes. Neem contact op met verkopervoor juiste procedure.Telecommunication Devices/ModemApprovalsThe telecommunication device in Motion Tablet PCs is approved for connection tothe telephone network in the countries whose approval markings are indicated onthe product label located on the Tablet PC or on an internal Tablet PC component.See the documentation included with the product to ensure the product is configuredfor the country in which it is located. Selecting a country other than the one in whichit is located may cause the modem to be configured in a way that violates thetelecommunications regulations of that country. In addition, the modem may notfunction properly if you make an incorrect country selection. When selecting acountry, if a message appears that states that the country is not supported, then themodem has not been approved for use in this country and should not be used.United States Modem StatementMotion Tablet PCs contain an internal modem that has been tested to comply withFCC Standards, specifically FCC Part 68 Reg. No: 5ZXMUL-36273-FB-E; ACREN:0.1B; USOC:RJ11; DOC REN:.0.0. The internal modem is located under therectangular Hard Disk Drive cover on the Tablet PC back panel and contains theregulatory label.Canadian Modem StatementThis equipment meets telecommunications network protective, operational, andsafety requirements as prescribed in the appropriate Terminal Equipment TechnicalRequirements document(s). This is confirmed by marking the equipment with the

English 17Industry Canada certification number. The Department does not guarantee that theequipment will operate to your satisfaction.Before installing the equipment, you should ensure that it is permissible to beconnected to the facilities of the local telecommunications company. The equipmentmust also be installed using an acceptable method of connection. You should beaware that compliance with the above conditions might not prevent degradation ofservice in some situations.Repairs to certified equipment should be coordinated by a representative designatedby the supplier. Any repairs or alterations made by you to this equipment, orequipment malfunctions, may give the telecommunications company cause torequest you to disconnect the equipment.You should ensure for your own protection that the electrical ground connections ofthe power utility, telephone lines, and internal metallic water pipe system, if present,are connected together. This precaution may be particularly important in rural areas.The Ringer Equivalence Number (REN) assigned to each terminal device providesan indication of the maximum number of terminals allowed to be connected to atelephone interface. The termination of an interface may consist of any combinationof devices, subject only to the requirement that the sum of the RENs of all thedevices does not exceed 5. The REN for this device is 1.

English18Other Notices and MarksBattery NoticeMotion Computing sealed lithium ion batteries comply with all applicable shippingregulations as prescribed by industry and legal standards. This includes compliancewith the UN Recommendations on the Transport of Dangerous Goods; IATA(International Air Transport Agency) Dangerous Goods Regulations, 44th Edition,2003, Special Provisions A45, and applicable U.S. DOT regulations for the safetransport of lithium ion batteries. Each Motion Computing cell or battery has beentested under provisions of the UN Manual of Tests and Criteria, Part III, Sub-section38.3.Laser Safety NoticeFor safety and regulatory information about third-party products that may containClass 1 laser equipment, see the documentation shipped with the product.Motion CDROM and DVD/CDRW drives are Class 1 laser products. A Class 1laser is considered to be incapable of producing damaging radiation levels and istherefore determined to be eye safe. These lasers are exempt from most controlmeasures. Many lasers in this class are lasers which are embedded in an enclosurethat prohibits or limits access to the laser radiation. However, we recommend thatyou do not stare into the beam or view it directly with optical instruments.

English 19Wireless NoticesIn some environments, the use of wireless devices may be restricted. Suchrestrictions may apply aboard airplanes, in hospitals, near explosives, in hazardouslocations, etc. If you are uncertain of the policy that applies to the use of this device,please ask for authorization to use it prior to turning it on. For instructions fordisabling internal and external wireless devices, see the section “Airline TravelNotice” in this guide.Saudi Arabian Quality MarkAll Motion Tablet PCs and Motion Tablet PC systems meet the Quality Markstandards issued by the Saudi Arabian Standards Organization (SASO) in Articles 3and 12 in Royal Decree No. M/10 dated 1392(H) - 03-03.Standards Applying Only to Motion M1200and M1300 Tablet PCs and AccessoriesNOTE: To determine what regulatory and safety marks apply to a specific product,component, or accessory, check the product label affixed to the product or its component.Australia Telecommunications (A-Tick)StatementAll Motion Tablet PCs and Motion Tablet PC systems meet the AustralianCommunications Authority (ASA) standards found in Schedule 3 of theLabeling Notice Radiocommunications Act of 1992 (A-Tick) forcompatibility for telecommunications-customer equipment.IMPORTANT TELECOMMUNICATIONS REGULATORY NOTICEThe user must not activate the decadic (pulse) dialing or Easycall functions of the Tablet PCinternal modem. The Tablet PC does not correctly support these functions for Australia andNew Zealand; use of these functions will void telecommunications compliance. The TabletPC shall be connected to the Telecommunications Network through a line cord that meets therequirements of ASA TS008.New Zealand Telecommunications (C-Tick)StatementAll Motion Tablet PCs and Motion Tablet PC systems comply with theNew Zealand Telecommunications Authority (NZTA) PTC200

English20specification for the internal modem. The permit number issued for this complianceappears on the regulatory label on the product.IMPORTANT TELECOMMUNICATIONS REGULATORY NOTICEThe user must not activate the decadic (pulse) dialing or Easycall functions of the Tablet PCinternal modem. The Tablet PC does not correctly support these functions for Australia andNew Zealand; use of these functions will void telecommunications compliance. The TabletPC shall be connected to the Telecommunications Network through a line cord that meets therequirements of ASA TS008.Standards Applying Only to Motion M1400Tablet PCsInternal Bluetooth Module NoticeClass B Equipment: This equipment has been tested and found to comply with thelimits for a Class B digital device, pursuant to part 15 of the FCC Rules. Theselimits are designed to provide reasonable protection against harmful interferencewhen the equipment is operated in a residential environment. This equipmentgenerates, uses, and can radiate radio frequency energy and, if not installed and usedin accordance with the manufacturer’s instruction manual, may cause interferencewith radio communications. However, there is no guarantee that interference willnot occur in a particular installation. If this equipment does cause harmfulinterference to radio or television reception, which can be determined by turning theequipment off and on, you are encouraged to try to correct the interference by one ormore of the following measures:■ Reorient or relocate the receiving antenna■ Increase the separation between the equipment and the receiver■ Connect the equipment into an outlet on a circuit different from that to which thereceiver is connected■ Consult the dealer or an experienced radio/television technicianfor help.This device complies with Part 15 of the Federal Communications Commission(FCC) Rules. Operation is subject to the following two conditions:■ This device may not cause harmful interference.■ This device must accept any interference received, including interference thatmay cause undesired operation.

English 21FCC Caution: Any changes or modification not expressly approved by the partyresponsible for compliance could void the user’s authority to operate this equipment.IMPORTANT NOTE:FCC Radiation Exposure Statement:! This equipment complies with FCC radiation exposure limits set forth for anuncontrolled environment.! This equipment also complies with FCC RF radiation exposure limits set forthfor an uncontrolled environment, under 47 CFR 2.1093 paragraph (d)(2), whichaddresses RF Exposure from radio frequency devices. Operation is within5.15GHz ~ 5.25GHz frequency range. This frequency range may limit orrestrict the effective use of this equipment to an indoor environment. Thisradiated output power is far below the FCC RF exposure limits. Nevertheless,this device should be used in such a manner that the potential for humancontact during normal operation is minimized. This equipment contains aninternal antenna transmitter whose effective use may be affected if it is co-located or operating in conjunction with any other antenna or transmitter.

Navigation menu