GemTek Technology CISCO867VAE XDSL Router User Manual HIG880 860

Gemtek Technology Co., Ltd. XDSL Router HIG880 860

User Manual Part 2

CHAPTER 2-1Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation GuideOL-16215-102Installing the RouterThis chapter describes the equipment and the procedures for successfully installing the Cisco 860 series, 880 series, and 890 series Integrated Services Routers (ISRs), and contains the following sections: • Equipment, Tools, and Connections, page 2-2 • Installing the Router, page 2-3Note For compliance and safety information, see the Regulatory Compliance and Safety Information Roadmap that ships with the router and the Regulatory Compliance and Safety Information for Cisco 800 Series and SOHO Series Routers.WarningAll wireless LAN products in the 5.2/5.3GHz band cannot be used outdoors. Use the product only indoors. Statement 372WarningRead the installation instructions before connecting the system to the power source. Statement 1004WarningOnly trained and qualified personnel should be allowed to install, replace, or service this equipment. Statement 1030WarningUltimate disposal of this product should be handled according to all national laws and regulations. Statement 1040WarningDo not locate the antenna near overhead power lines or other electric light or power circuits, or where it can come into contact with such circuits. When installing the antenna, take extreme care not to come into contact with such circuits, because they may cause serious injury or death. For proper installation and grounding of the antenna, please refer to national and local codes (for example, U.S.:NFPA 70, National Electrical Code, Article 810, Canada: Canadian Electrical Code, Section 54). Statement 1052WarningNo user-serviceable parts inside. Do not open. Statement 1073
2-2Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation GuideOL-16215-10Chapter 2 Installing the Router Equipment, Tools, and ConnectionsEquipment, Tools, and ConnectionsThis section describes the equipment, tools, and connections necessary for installing your Cisco 860 series, 880 series, and 890 series ISRs. It contains the following topics: • Items Shipped with your Router, page 2-2 • Additional Items, page 2-2 • Connections, page 2-3 • Ethernet Devices, page 2-3Items Shipped with your RouterUnpack the box and verify that all items listed on the invoice were shipped with the router.Table 2-1 lists the items and their quantities that are shipped with each router model.Additional ItemsThe following items are not shipped with the router but are required for installation: • ESD-preventive cord and wrist strap. • Screws for mounting the router on a wall:Ta b l e 2-1 Items and Their Quantities That Are Shipped with the Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series ISRs ItemCisco 860 Series RoutersCisco 860VAE Series Routers11. By default, no cables are shipped with Cisco 860VAE models unless requested through the dynamic configuration tool.Cisco 880 Series RoutersCisco 890 Series RoutersStraight-through RJ-45 Ethernet cable 1 — 1 1ADSL RJ-11-to-RJ-11 straight-through cable ———1RJ-11 DSL2 cable2. DSL = digital subscriber line.133. Shipped with Cisco 867 models only.n/a 144. Shipped with Cisco 886, 887, 887M, and 886-J models only.1DSL RJ-45-to-dual-RJ-11 breakout cable —n/a 155. Shipped with Cisco 888E models only.1RJ-45-to-DB-9 console cable 1 — 1 1External 12 VDC power supply adapter 1111AC power supply cable with cable retention clip 1111Cisco Configuration Professional (Cisco CP) CD66. Cisco CP is optional by order and available only on some SKUs.1111
2-3Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation GuideOL-16215-10Chapter 2 Installing the Router Installing the Router –Two number-10 wood screws (round- or pan-head) with number-10 washers, or two number-10 washer-head screws, for mounting on a wall stud. The screws must be long enough to penetrate at least 3/4 in. (20 mm) into the supporting wood or metal wall stud. –Two number-10 wall anchors with washers, for mounting the router on a hollow-wall. • Wire crimper for chassis grounding. • Wire for connecting the chassis to an earth ground: –AWG 14 (2 mm2) or larger wire for NEC-compliant chassis grounding. –AWG 18 (1 mm2) or larger wire for EN/IEC 60950–compliant chassis grounding. • Ring terminal with an inner diameter of 1/4 in. (5 to 7 mm), for NEC-compliant chassis grounding. • Ethernet cables for connecting to the Fast Ethernet (FE) WAN and LAN ports.ConnectionsObtain a broadband or Ethernet connection from your service provider.Ethernet DevicesIdentify the Ethernet devices that you will connect to the router: hub, servers, and workstations or PCs. Ensure that each device has a network interface card (NIC) for connecting to Ethernet ports. • If you plan to configure the software using Cisco IOS commands through the console port, provide an ASCII terminal or a PC that is running terminal emulation software to connect to the console port. • If you plan to connect a modem, provide the modem and modem cable. • If you plan to use the Data BRI port, provide an NT1 device and an ISDN S/T cable. • If you plan to use the cable-lock feature, provide a Kensington or equivalent locking cable.Installing the RouterThis section describes how to install the Cisco 860 series, 880 series, and 890 series ISRs. These routers can either be installed on a table top or other flat horizontal surface or be mounted on a wall. The Cisco 890 series ISRs may be mounted in a rack. This section also describes how to attach WLAN antennas to the Cisco 890 series routers. This section contains the following topics: • Warnings, page 2-4 • Installing Antennas, page 2-4 • Installing on a Table, page 2-7 • Mounting on a Wall, page 2-8 • Installing in a Rack, page 2-11 • Installing the Router Ground Connection, page 2-13 • Installing the FIPS Cover, page 2-14
2-4Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation GuideOL-16215-10Chapter 2 Installing the Router Installing the RouterWarningsWarningThis equipment needs to be grounded. Use a green and yellow 12 to 14 AWG ground wire to connect the host to earth ground during normal use. Statement 242WarningThis equipment must be grounded. Never defeat the ground conductor or operate the equipment in the absence of a suitably installed ground conductor. Contact the appropriate electrical inspection authority or an electrician if you are uncertain that suitable grounding is available. Statement 1024WarningRead the wall-mounting instructions carefully before beginning installation. Failure to use the correct hardware or to follow the correct procedures could result in a hazardous situation to people and damage to the system. Statement 378Note • Do not stack anything on top of the router. • Do not cover or obstruct the router vents located on both sides and top of the routers; otherwise, overheating could occur and cause damage to the router. • Place router in ventilated area to avoid local air heating.Caution Do not cover or obstruct the router vents located on both sides of the router; otherwise, overheating could occur and cause damage to the router.Caution Do not place anything on top of the router that weighs more than 10 pounds (4.5 kilograms), and do not stack routers on a desktop. Excessive weight on top of the router could damage the chassis.Caution Do not install the router or power supplies next to a heat source of any kind, including heating vents.Caution The top surface of the router is hot since heat is dissipated through the top. Do not keep any object in direct contact with the surface for a prolonged period.Installing AntennasThe Cisco 890 series wireless routers have three reverse-polarity threaded Neill-Concelman (RP-TNC) connectors on the back panel. The antennas that are shipped with the router are dual-band 2.4-GHz to 5-GHz omnidirectional dipole antennas.
2-5Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation GuideOL-16215-10Chapter 2 Installing the Router Installing the RouterWarningAll wireless LAN products in the 5.2/5.3GHz band cannot be used outdoors. Use the product only indoors. Statement 372Note Before you install the Cisco 890 series wireless router on a table, wall, or rack, connect the antennas to the back panel. It is difficult to attach the antennas after the router is installed.To attach the radio antennas to your wireless router, follow these steps:Step 1 Manually screw the antennas tight to the RP-TNC connectors on the back of the router.Figure 2-1 Attaching Antennas to the RouterStep 2 Orient the antennas. For optimum wireless performance, the antennas should be perpendicular with respect to the floor.a. If the router is being mounted on a desk, orient the antennas straight up.b. If the router is being mounted on a wall, orient the antennas perpendicular to the floor, as shown in Figure 2-2 and Figure 2-3.272486
2-6Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation GuideOL-16215-10Chapter 2 Installing the Router Installing the RouterFigure 2-2 Antennas Oriented Vertically Up274774
2-7Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation GuideOL-16215-10Chapter 2 Installing the Router Installing the RouterFigure 2-3 Antennas Oriented Vertically DownInstalling on a TableTo install the router on a table or other flat horizontal surface, firmly place the router on a table or other horizontal surface. Keep at least 1 inch (2.5 cm) of clear space beside the cooling inlet and exhaust vents.Connect the chassis to a reliable earth ground. For the chassis ground connection procedures, see the “Installing the Router Ground Connection” section on page 2-13.Note Do not place anything on top of the router.274775
2-8Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation GuideOL-16215-10Chapter 2 Installing the Router Installing the RouterMounting on a WallThe Cisco 860 series, 880 series, and 890 series ISRs have mounting holes on the bottom of the chassis for mounting the unit on a wall or other vertical surface.The mounting holes are bidirectional. You can hang the router with the front bezel facing upward or downward.Keep at least 1 inch (2.5 cm) of clear space beside the cooling inlet and exhaust vents.Tip When choosing a location for wall-mounting the router, consider cable limitations and wall structure.To mount the router on a wall, follow these steps:Step 1 Determine the required distance between mounting holes on the router. Figure 2-4 shows the wall-mount holes located on the underside of the router.Note For most router models, the distance between mounting holes is 8.2 inches (208 mm), as shown in Figure 2-4. For the Cisco 866 and Cisco 867 models, the distance is 7.85 inches (199 mm). Verify the required distance before drilling the holes.
2-9Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation GuideOL-16215-10Chapter 2 Installing the Router Installing the RouterFigure 2-4 Wall-mount Holes on the Underside of the RouterStep 2 Insert the screws, with anchors, into the wall. Leave 1/8 inch (0.32 cm) between the screw head and the wall. See Figure 2-5.Step 3 Hang the router on the screw without forcibly pushing towards the wall side. The screw head may damage the protection wall inside. Place the power adapter on a nearby horizontal surface. See Figure 2-5.1Wall-mount holes23198713.673 in.8.200 in.5.961 in.1
2-10Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation GuideOL-16215-10Chapter 2 Installing the Router Installing the RouterFigure 2-5 Router Mounted on the WallStep 4 Connect the chassis to a reliable earth ground. For the chassis ground connection procedures, see the “Installing the Router Ground Connection” section on page 2-13.1Two number-10 wood screws mounted on the wall3Horizontal surface on which to place the power adapter2Wall-mount holes 4Distance between the screw head and the wall, 1/8 in. (0.32 cm)23198242113
2-11Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation GuideOL-16215-10Chapter 2 Installing the Router Installing the RouterInstalling in a RackThe Cisco 890 series ISRs can be mounted in a rack. To install a Cisco 890 series ISR in a rack, follow these steps:Step 1 Remove the screws, as shown in Figure 2-6.Figure 2-6 Screw LocationsStep 2 Using the screws provided, attach the rack-mount brackets to the Cisco 890 series ISR chassis, as shown in Figure 2-7. Use two screws on each side. Use a number 2 Phillips screwdriver to install the bracket screws on both sides of the chassis.Caution Do not over torque the screws. The recommended torque is 6 to 8 in-lb (0.7 to 0.9 N-m).Figure 2-7 Attaching the Rack-mount Brackets to the Cisco 890 Series ISR1Screws27815911272484
2-12Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation GuideOL-16215-10Chapter 2 Installing the Router Installing the RouterCaution Chassis installation must allow unrestricted airflow for chassis cooling. Step 3 Using two screws for each side (supplied with the rack), attach the Cisco 890 series ISR with rack-mount brackets to a 19-inch rack. Start with the lower pair of screws first, resting the brackets on the lower screws while you insert the upper pair of screws.Note Be sure to leave space above and below each unit in a rack to allow for cooling air circulation. Note Do not stack equipment directly above the router. Keep at least 1 rack unit of space above the router.Tip The screw slots in the brackets are spaced to line up with every second pair of screw holes in the rack. When the correct screw holes are used, the small threaded holes in the brackets line up with unused screw holes in the rack. If the small holes do not line up with the rack holes, you must raise or lower the brackets to the next rack hole.Step 4 Place the power adapter on a nearby horizontal surface.Step 5 Connect the chassis to a reliable earth ground. For the chassis ground connection procedures, see the “Installing the Router Ground Connection” section on page 2-13.WarningTo prevent bodily injury when mounting or servicing this unit in a rack, you must take special precautions to ensure that the system remains stable. The following guidelines are provided to ensure your safety: • This unit should be mounted at the bottom of the rack if it is the only unit in the rack. • When mounting this unit in a partially filled rack, load the rack from the bottom to the top with the heaviest component at the bottom of the rack. • If the rack is provided with stabilizing devices, install the stabilizers before mounting or servicing the unit in the rack. Statement 1006
2-13Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation GuideOL-16215-10Chapter 2 Installing the Router Installing the RouterInstalling the Router Ground ConnectionThe router must be connected to a reliable earth ground. Install the ground wire in accordance with local electrical safety standards. • For NEC-compliant grounding, use size 14 AWG (2 mm2) or larger copper wire and a ring terminal with an inner diameter of 1/4 in. (5 to 7 mm). • For EN/IEC 60950–compliant grounding, use size 18 AWG (1 mm2) or larger copper wire.To install the ground connection, follow these steps:Step 1 Strip one end of the ground wire to the length required for the ground lug or terminal.Step 2 Crimp the ground wire to the ground lug or ring terminal, using the wire crimper.Step 3 Attach the ground lug or ring terminal to the chassis, as shown in Figure 2-8. For a ground lug, use the two provided screws with captive locking washers. For a ring terminal, use one of the screws provided. Tighten the screws to a torque of 8 to 10 in-lb (0.9 to 1.1 N-m).Figure 2-8 Chassis Ground Connection Using Ring TerminalStep 4 Connect the other end of the ground wire to a known reliable earth ground point at your site. After you install and properly ground the router, you can connect the power wiring, the WAN and LAN cables, and the cables for administrative access as required for your installation.1Ring terminal2319811
2-14Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation GuideOL-16215-10Chapter 2 Installing the Router Installing the RouterInstalling the FIPS CoverPerform the following steps to install the FIPS cover in the router:Step 1 Remove the four mounting screws of the top cover.284921
2-15Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation GuideOL-16215-10Chapter 2 Installing the Router Installing the RouterStep 2 Install the left-side FIPS cover, as shown in detail A. Step 3 Rotate and bring into the close position to hinge to the correct hexagon. Step 4 Place the adapter plate before closing by aligning the mounting holes.284922Detail AAdapterPlate
2-16Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation GuideOL-16215-10Chapter 2 Installing the Router Installing the RouterStep 5 Secure the FIPS cover with two mounting screws.Step 6 Install the right-side FIPS cover the same way as the left-side FIPS cover.Step 7 View after both covers are installed.284923284924
2-17Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation GuideOL-16215-10Chapter 2 Installing the Router Installing the RouterStep 8 If the FIPS covers are installed with the rack mount brackets, the adapter plates are not required in the installation.284925
2-18Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation GuideOL-16215-10Chapter 2 Installing the Router Installing the Router
CHAPTER 3-1Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation GuideOL-16215-103Connecting the RouterThis chapter describes how to connect Cisco 860 series, Cisco 880 series, and Cisco 890 series Integrated Services Routers (ISRs) to Ethernet devices, Power over Ethernet (PoE), and a network. The chapter contains the following sections: • Safety Warnings, page 3-2 • Preparing to Connect the Router, page 3-4 • Connecting a PC, Server, or Workstation, page 3-5 • Connecting a Phone, page 3-6 • Connecting an External Ethernet Switch, page 3-7 • Connecting the V.92 modem Port, page 3-8 • Connecting a Terminal or PC to the Console Port, page 3-9 • Connecting a Modem to the Auxiliary Port, page 3-10 • Connecting the 3G Card, page 3-11 • Installing the 3G Adapter for Extended Cable/Antenna, page 3-17 • Connecting a Data BRI Port, page 3-21 • Connecting an FE Line to an FE WAN Port, page 3-23 • Connecting a GE Line to an GE WAN Port, page 3-24 • Connecting an xDSL Line, page 3-25 • Connecting Power over Ethernet, page 3-27 • Connecting the AC Adapter, page 3-28 • Connecting an FXS Line, page 3-32 • Connecting an FXO Line, page 3-34 • Connecting a Voice ISDN BRI Line, page 3-35 • Connecting a Small Form-Factor Pluggable Module, page 3-37 • Verifying Connections, page 3-40Note For compliance and safety information, see Regulatory Compliance and Safety Information Roadmap that ships with the router and Regulatory Compliance and Safety Information for Cisco 800 Series and SOHO Series Routers.
http://www.cisco.com/en/US/docs/routers/access/800/rcsi/800srcsi.html">
http://www.cisco.com/en/US/docs/routers/access/800/rcsi/800srcsi.html">
3-2Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation GuideOL-16215-10Chapter 3 Connecting the Router Safety WarningsNote The illustrations in this chapter show a wireless router with antennas attached. Non-wireless routers do not have antennas or antenna connectors on the back panel. However, the procedures for connecting devices to the router are the same for both wireless and non-wireless routers. Note Depending on the features available for your router, some content in this chapter may not apply to your router.Safety WarningsWarningWhen installing the product, please use the provided or designated connection cables/power cables/AC adaptors/batteries. Using any other cables/adaptors could cause a malfunction or a fire. Electrical Appliance and Material Safety Law prohibits the use of UL-certified cables (that have the “UL” or “CSA” shown on the cord), not regulated with the subject law by showing “PSE” on the cord, for any other electrical devices than products designated by CISCO. Statement 371WarningDo not work on the system or connect or disconnect cables during periods of lightning activity. Statement 1001WarningThis equipment has been designed for connection to TN and IT power systems. Statement 1007WarningThere is the danger of explosion if the battery is replaced incorrectly. Replace the battery only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions. Statement 1015WarningTake care when connecting units to the supply circuit so that wiring is not overloaded. Statement 1018WarningTo avoid electric shock, do not connect safety extra-low voltage (SELV) circuits to telephone-network voltage (TNV) circuits. LAN ports contain SELV circuits, and WAN ports contain TNV circuits. Some LAN and WAN ports both use RJ-45 connectors. Use caution when connecting cables. Statement 1021WarningHazardous network voltages are present in WAN ports regardless of whether power to the unit is OFF or ON. To avoid electric shock, use caution when working near WAN ports. When detaching cables, detach the end away from the unit first. Statement 1026WarningOnly trained and qualified personnel should be allowed to install, replace, or service this equipment. Statement 1030
3-3Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation GuideOL-16215-10Chapter 3 Connecting the Router Safety WarningsWarningDo not use this product near water; for example, near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement, or near a swimming pool. Statement 1035WarningNever install telephone jacks in wet locations unless the jack is specifically designed for wet locations. Statement 1036WarningNever touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface. Statement 1037WarningAvoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning. Statement 1038WarningTo report a gas leak, do not use a telephone in the vicinity of the leak. Statement 1039WarningBefore opening the unit, disconnect the telephone-network cables to avoid contact with telephone-network voltages. Statement 1041WarningThis equipment contains a ring signal generator (ringer), which is a source of hazardous voltage. Do not touch the RJ-11 (phone) port wires (conductors), the conductors of a cable connected to the RJ-11 port, or the associated circuit-board when the ringer is active. The ringer is activated by an incoming call. Statement 1042WarningDo not locate the antenna near overhead power lines or other electric light or power circuits, or where it can come into contact with such circuits. When installing the antenna, take extreme care not to come into contact with such circuits, because they may cause serious injury or death. For proper installation and grounding of the antenna, please refer to national and local codes (for example, U.S.:NFPA 70, National Electrical Code, Article 810, Canada: Canadian Electrical Code, Section 54). Statement 1052WarningNo user-serviceable parts inside. Do not open. Statement 1073WarningInstallation of the equipment must comply with local and national electrical codes. Statement 1074
3-4Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation GuideOL-16215-10Chapter 3 Connecting the Router Preparing to Connect the RouterPreparing to Connect the RouterBefore you connect the router to the devices, install the router according to the instructions in “Installing the Router” section on page 2-1Preventing Damage to the RouterTo prevent damage to your router, follow these guidelines when connecting devices to your router: • Turn off power to the devices and to the router until all connections are completed.Caution Do not turn on the devices until after you have completed all connections to the router. • Connect the color-coded cables supplied by Cisco to the color-coded ports on the back panel. • If you must supply your own cable, see “Technical Specifications” section on page A-1 for cabling specifications. If this appendix does not provide specifications for a particular cable, we strongly recommend ordering the cable from Cisco.
3-5Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation GuideOL-16215-10Chapter 3 Connecting the Router Connecting a PC, Server, or WorkstationConnecting a PC, Server, or WorkstationTo connect a PC (or other Ethernet devices) to an Ethernet switch port, follow these steps:Step 1 Connect one end of the yellow Ethernet cable to an Ethernet switch port on the router. Figure 3-1 shows a Cisco 888W router connected to a PC.Figure 3-1 Connecting a Server, PC, or WorkstationStep 2 Connect the other end of the cable to the RJ-45 port on the network interface card (NIC) that is installed in the PC, server, or workstation.Step 3 (Optional) Connect additional servers, PCs, or workstations to the other Ethernet switch ports.Note Use the Cisco Configuration Express to configure the Internet connection settings. See Cisco Configuration Professional Quick Start Guide for more information.1Yellow Ethernet cable supplied with the router 3RJ-45 port on the network interface card2Ethernet switch port on the router322319891
">
3-6Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation GuideOL-16215-10Chapter 3 Connecting the Router Connecting a PhoneConnecting a PhoneTo connect an 802.3af-compliant phone to an Ethernet switch port, follow these steps:Note A power source must be provided for the phone to function. This can be done in two ways: the phone can be powered via the PoE function using the PoE enabled Ethernet ports, or by using an external AC power source connected to the phone.Step 1 Connect one end of the yellow Ethernet cable to Ethernet switch port 0 or port 1 on the router. Figure 3-2 shows a Cisco 888W router connected to a phone.Figure 3-2 Connecting a Phone1Yellow Ethernet cable 3RJ-45 port on a phone2Ethernet switch port 1 on the router32270551112ABC3DEF45JKLGHI6MNO78TUVPQRS9WXYZ*0OPER#
3-7Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation GuideOL-16215-10Chapter 3 Connecting the Router Connecting an External Ethernet SwitchStep 2 Connect the other end of the cable to the RJ-45 port on the phone.Connecting an External Ethernet Switch If more than four PCs in an office must be connected to each other, you can add Ethernet connections to the router by connecting an external Ethernet switch to the Ethernet switch on the router. To connect an external Ethernet switch to an Ethernet switch port on the router, complete the following steps:Step 1 Connect one end of the yellow Ethernet cable to an Ethernet switch port on the router. Figure 3-3 shows a Cisco 888W router connected to an Ethernet switch.Figure 3-3 Connecting to an Ethernet SwitchStep 2 Connect the other end of the cable to the available port on the Ethernet switch to add additional Ethernet connections.Step 3 Turn on the Ethernet switch.1 Ethernet switch port on the router 3Yellow CAT5 Ethernet cable, RJ-45–to–RJ-45, connecting to an external Ethernet switch port2Available port on the external Ethernet switchMODECatalyst 3500 SERIES XL INLINE POWERSYSTEM1X2X15X16XRPSSTATUSUTILDUPLXSPEED12345678910 11 1211X2X15X16X12345678910 11 122231986132
3-8Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation GuideOL-16215-10Chapter 3 Connecting the Router Connecting the V.92 modem PortConnecting the V.92 modem PortWarningHazardous network voltages are present in WAN ports regardless of whether power to the unit is OFF or ON. To avoid electric shock, use caution when working near WAN ports. When detaching cables, detach the end away from the unit first. Statement 1026For dialup connection to your service provider network through the V.92 port, follow the steps given after Figure 3-4, which show this connection.Figure 3-4 Connecting to Your Service Provider Through the V.92 portTo connect the router to your service provide network through the V.92 port, follow these steps:Step 1 Connect one end of the straight-through R-J11 cable to the V.92 port. Step 2 Connect the other end of the straight through R-J11 cable to an RJ-11 telephone wall outlet. 1V.92 port on the router 2Telephone wall outlet27238712
3-9Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation GuideOL-16215-10Chapter 3 Connecting the Router Connecting a Terminal or PC to the Console PortConnecting a Terminal or PC to the Console PortConnect a terminal or PC to the Console Auxiliary (Aux) port either to configure the software by using the CLI or to troubleshoot problems with the router. To connect a terminal or PC to the console port on the router and access the CLI, follow these steps:Step 1 Connect the RJ-45 end of a DB-9–to–RJ-45 serial cable to the RJ-45 Console Aux port on the router. Figure 3-5 shows the RJ-45 end of the serial cable connected to the Console Aux port on the router. Figure 3-5 Connecting a Terminal or PC to the Console PortStep 2 Connect the DB-9 end of the DB-9–to–RJ-45 serial cable to the to the COM port on your laptop or PC.Note Some laptops and PCs do not come with DB-9 serial port connectors and may require a USB-to-serial port adapter.Step 3 To communicate with the router, start a terminal emulator application.1 RJ-45 connector to the Console Aux port on the router2DB-9 connector21231990
3-10Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation GuideOL-16215-10Chapter 3 Connecting the Router Connecting a Modem to the Auxiliary PortTerminal Emulator SettingsUse the following settings for the terminal emulator connection: • 9600 baud • 8 data bits, no parity • 1 stop bit • No flow control When the terminal emulator establishes communications, the router prompt is displayed.For more information on terminal emulation settings, see Applying Correct Terminal Emulator Settings for Console Connections.Connecting a Modem to the Auxiliary PortTo connect a modem to the router, follow these steps:Step 1 Connect the RJ-45 end of the adapter cable to the Aux port on the router as shown in Figure 3-6. Figure 3-6 Connecting a Modem to the Aux Port1Aux port (RJ-45) 3DB-9 to DB-25 modem adapter (if required)2Light blue console cable 4Modem2723861234
3-11Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation GuideOL-16215-10Chapter 3 Connecting the Router Connecting the 3G CardStep 2 Connect the DB-9 end of the console cable to the DB-9 end of the modem adapter. Step 3 Connect the DB-25 end of the modem adapter to the modem.Step 4 Make sure that your modem and the router auxiliary port are configured for the same transmission speed (up to 115200 bits per second [b/s] is supported) and support mode control with data carrier detect (DCD) and data terminal ready (DTR).Connecting the 3G CardNote For information on embedded multiband, multiservice WAN modems, see Configuring Cisco EHWIC and 880G for 3G (EV-DO Rev A) and Configuring Cisco EHWIC and 880G for 3.7G (HSPA+)/3.5G (HSPA). Note The Cisco 880G router does not support online insertion and removal (OIR) of the third-generation (3G) card. You must enter the shutdown command on the cellular interface before you remove the 3G card from the router. To connect and secure the 3G card, follow these steps:Step 1 Align the 3G card to the 3G express card slot, as shown in Figure 3-7. Keep the card parallel to the surface and firmly push the card into the slot.Tip Holding the 3G card on the flat metal surface makes it easier to align and insert the 3G card.Note When inserting the card into the 3G express card slot, you may hear a metal-on-metal sound as the 3G card rubs against the internal metal cage. The 3G card is designed to fit tightly into the 3G express card slot. Firm pressure may be required to insert the card.Note Global System for Mobile Communications (GSM) customers need to insert a SIM card, provided by their network carrier, into the 3G card.
3-12Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation GuideOL-16215-10Chapter 3 Connecting the Router Connecting the 3G CardFigure 3-7 Inserting the 3G CardStep 2 Open the top of the anti-theft locking bracket, as shown in Figure 3-8. Figure 3-8 Opening the Anti-theft Locking Bracket13G card with the Cisco logo facing up 4Screw holes for locking bracket23G express card slot 5Pin holes for aligning the locking bracket3Notches on the 3G card 6SIM slot (in HSPA1 cards only)1. HSPA = High-Speed Packet Access.271473162545331Pins on the locking bracket for alignment271474Front View Back View11
3-13Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation GuideOL-16215-10Chapter 3 Connecting the Router Connecting the 3G CardStep 3 Slide the opened locking bracket under the 3G card. The locking bracket should align with the notches on either side of the 3G card, as shown in Figure 3-9, and the pins on the locking bracket should be inserted into the corresponding holes in the router. Figure 3-9 Installing the Locking Bracket13G card 3Notch on the 3G card2Locking bracket123271726
3-14Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation GuideOL-16215-10Chapter 3 Connecting the Router Connecting the 3G CardStep 4 Close the locking bracket, as shown in Figure 3-10.Figure 3-10 Closing the Locking BracketStep 5 Insert the screws, as shown in Figure 3-11, and tighten with a number 2 Phillips screwdriver.Figure 3-11 Inserting the ScrewsStep 6 To connect the antenna to the 3G card, insert the antenna connector into the antenna connector receptacle on the 3G card.13G card 2Locking bracket1227158013G card 3Screws2Locking bracket 4Screw holes on the locking bracket27147634214
3-15Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation GuideOL-16215-10Chapter 3 Connecting the Router Connecting the 3G CardNote The antenna connector receptacle may be located on the left, right, or front of the 3G card, depending on your card. Figure 3-12 shows the antenna connected to the 3G card with an SSMB type plug, and Figure 3-13 shows the antenna with the SMK-TS-9 connector.Figure 3-12 Antenna connected to the 3G Card with SSMB connector1Antenna on a cradle 3Antenna connector receptacle11. The antenna connector receptacle is located on either the left, right or front of the card for different SKUs. Please locate the receptacle of your card before plugging in the cable.2Antenna SSMB connector272653123
3-16Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation GuideOL-16215-10Chapter 3 Connecting the Router Connecting the 3G CardFigure 3-13 Antenna with the SMK-TS- 9 ConnectorIf you are using an extension cable, you must attach the 3G adapter for extended cable antenna to the body of the router. Depending on the SKU ordered, the adapters come with different connectors. Table 3-1 lists the different adapters and SKUs supported by each adapter. For instructions on how to install the adapter, see the “Installing the 3G Adapter for Extended Cable/Antenna” section on page 3-17. Otherwise, follow Step 7.Step 7 Clean the flat surface to which you will affix the antenna.279085Originalantenna assemblySMK-TS-9connector CableTa b l e 3-1 3G Adapters and Supported SKUs 3G Adapter SKU Description SKUs Supported3G-ACC-SMKTS9-TNC 3G adapter for extended cable/antenna with an SMK-TS-9 to TNC connector. Use this with the pentaband dipole indoor antenna (3G-ANTM-SMKTS9).PCEX-3G-HSPA-R6, CISCO881G-G-K93G-ACC-SSMB-TNC 3G adapter for extended cable/antenna with an SSMB to TNC connector. Use this with the pentaband dipole indoor antenna shipped with your product.PCEX-3G-HSPA, PCEX-3G-HSPA-A, PCEX-3G-CDMA-S, PCEX-3G-CDMA-V, PCEX-3G-CDMA-B, CISCO881G-A-K9, CISCO881G-S-K9, CISCO881G-V-K9
3-17Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation GuideOL-16215-10Chapter 3 Connecting the Router Installing the 3G Adapter for Extended Cable/AntennaStep 8 Remove the protective tape from the adhesive on the bottom of the antenna cradle, then firmly press the cradle to the flat surface. Installing the 3G Adapter for Extended Cable/AntennaFor better signal and reception, if you are using the Cisco 3G Adapter for Extended Cable/Antenna, 3G-ACC-SMKTS9-TNC, follow these steps to install it:Step 1 Locate and remove the Phillips screw on the left side of the router as shown in Figure 3-14. Keep the screw aside for Step 4.Figure 3-14 Locating the Phillips Screw 1Phillips screw on the left side of router 2Air vent holes to be aligned with adapter279124221
3-18Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation GuideOL-16215-10Chapter 3 Connecting the Router Installing the 3G Adapter for Extended Cable/AntennaStep 2 Locate the hooks on the adapter as shown in Figure 3-15.Figure 3-15 Locating the Hooks on the AdapterStep 3 Align and insert the hooks of the adapter into the air vent holes on the left side router body as shown in Figure 3-16.Figure 3-16 Inserting the Hooks27912211Hooks on the adapter 279123111Hooks aligned and inserted into the router.
3-19Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation GuideOL-16215-10Chapter 3 Connecting the Router Installing the 3G Adapter for Extended Cable/AntennaStep 4 Align the circular adapter hole with the hole on the router chassis from where you removed the screw in Step 1 and use the screw to attach the adapter to the router as shown in Figure 3-17.Figure 3-17 Attaching the Adapter279091
3-20Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation GuideOL-16215-10Chapter 3 Connecting the Router Installing the 3G Adapter for Extended Cable/AntennaStep 5 Connect the extension cable to the 3G card, as described in the “Connecting the 3G Card” section on page 3-11. The complete assembly is shown in Figure 3-18.Figure 3-18 Adapter Connected to 3G Card and Router ChassisNow the adapter is ready for use with the extension cable. Table 3-2 lists the loss information for the ultra-low-loss (ULL) LMR 400 cables available with the adpater for the 3G fixed platforms.1Router chassis 4SSMB or SMK-TS-9 connector23G adapter for extended cable/antenna 53G card inserted into the router3Cable 63G card279089321654
3-21Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation GuideOL-16215-10Chapter 3 Connecting the Router Connecting a Data BRI PortNote Antenna orientation can increase or decrease signal reception due to polarization. Typically, an SP’s transmitting antenna on the BTS is a vertically polarized omnidirectional antenna, which means the electromagnetic waves are transmitted from it in a vertical plane. Hence, the receiving antenna needs to be vertically oriented too in order to receive the best signal. As the angle of the antenna orientation is changed from vertical to horizontal, only an angular component of the signal is picked up by the antenna. Therefore, if the antenna orientation is horizontal, the antenna picks up the least signal. The signal is received by the antenna as a result of it bouncing off of reflective surfaces. Hence, depending on where the antenna is placed, it may receive different signal strengths. However, the recommended position is vertical.For additional information on all the available cables and antennas available for 3G, go to: http://www.cisco.com/en/US/docs/routers/access/1800/1861/software/feature/guide/mrwlsgsm.html#wp1262730Connecting a Data BRI PortYou can connect the Data BRI port to the ISDN service provider as a backup link to the WAN port in case the primary xDSL (general term referring to various forms of DSL, including global industry standard symmetrical high-speed DSL [G.SHDSL]) WAN service fails. The Data BRI connection is not available on the third-generation (3G) models. The cabling requirements for the ISDN S/T connection are as follows: • You must provide two unshielded Category 5 cables. The first cable connects the NT1 box to the splitter, and the second cable connects the splitter to the wall jack. • There are RJ-45 connectors at both ends of the default orange ISDN S/T cable. However, an RJ-45–to–RJ-11 ISDN S/T cable is available upon request if the wall jack at the site requires an RJ-11 connector. Contact your router reseller for the appropriate cable.Caution Both LAN and WAN ports use RJ-45 connectors. Use caution when connecting cables to these connectors. To avoid damage to the router, do not connect telephone-network voltage (TNV) circuits (such as ISDN or DSL circuits) to safety extra-low voltage (SELV) circuits (such as LAN circuits). Although the following procedure shows a Cisco 888W data router, this procedure applies to all Cisco 880 series router with a Data BRI port.Ta b l e 3-2 Cisco Adapter Cables for Use with 3G Fixed Routers Cisco Product NumberAntenna Adapter Length Insertion Loss Frequency (MHz)3G-ACC-SSMB-TNC 14.5 inches 0.66 dB 2100 3G-ACC-TS9-TNC 13.5 inches 0.62 dB 2100
3-22Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation GuideOL-16215-10Chapter 3 Connecting the Router Connecting a Data BRI PortTo connect the Data BRI port to the ISDN service provider, follow these steps:Step 1 Connect one end of the orange ISDN S/T cable to the Data BRI port on the router. Figure 3-19 shows a Data BRI connection.Figure 3-19 Connecting the Data BRI Port to the ISDN LineStep 2 Connect the other end of the orange ISDN S/T cable to the S/T port on the NT1 box.Step 3 Connect the first unshielded CAT 5 cable from the U-port on the NT1 box to the telephone line port on the splitter. Step 4 Connect the second unshielded Category 5 cable from the telecommunication service port on the splitter to the wall jack to allow a link to the network service provider.1Data BRI port on the router 6U-port on the NT1 box2ISDN S/T cable 7xDSL splitter (provided by the xDSL service provider)3Network termination 1 (NT1) box 8Telephone line port on the splitter4S/T port on the NT1 box 9Telecommunication service port on the splitter5Unshielded CAT 5 cable 10 Wall jack231991314210698755
3-23Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation GuideOL-16215-10Chapter 3 Connecting the Router Connecting an FE Line to an FE WAN PortConnecting an FE Line to an FE WAN PortTo connect the Fast Ethernet (FE) WAN port on the router, follow these steps:Step 1 Connect one end of the yellow cable to the FE WAN port as shown in Figure 3-20.Figure 3-20 Connecting the FE WAN PortStep 2 Connect the other end of cable to an available port on the modem.1FE WAN port 3Modem connected to the Internet2CAT 5 cableWANFE 41InternetInternetInternet232319921
3-24Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation GuideOL-16215-10Chapter 3 Connecting the Router Connecting a GE Line to an GE WAN PortConnecting a GE Line to an GE WAN PortTo connect the Gigabit Ethernet (GE) WAN port on the router, follow these steps:Step 1 Connect one end of the yellow cable to the GE WAN port as shown in Figure 3-21.Figure 3-21 Connecting the GE WAN PortStep 2 Connect the other end of cable to an available port on the modem.1GE WAN port 3Modem connected to the Internet2CAT 5 cableInternetInternetInternet232744931
3-25Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation GuideOL-16215-10Chapter 3 Connecting the Router Connecting an xDSL LineConnecting an xDSL Line WarningHazardous network voltages are present in WAN ports regardless of whether power to the unit is OFF or ON. To avoid electric shock, use caution when working near WAN ports. When detaching cables, detach the end away from the unit first. Statement 1026Caution Cisco Systems DSL WAN Interfaces are tested for compliance with regulatory standards such as FCC Part 68, ITU-T K.21, IEC 61000-4-5, and CSA/EN/IEC/UL 60950-1. These standards assume Primary Protection devices protect the Customer Premise Equipment (CPE). These devices are normally installed by the service provider, local exchange carrier or qualified service person and are located at the telecom service provider entrance, network interface box, or demarcation point. See Figure 3-22 for the likely location of the primary protection device. The primary protection device must be suitable for the xDSL interface employed. Please contact your sales team or qualified service person for further information and installation.Caution To reduce the risk of fire, use only No. 26 AWG or larger (e.g., 24 AWG) UL Listed or CSA Certified Telecommunication Line Cord.WarningDo not use this product near water; for example, near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement, or near a swimming pool. Statement 1035WarningAvoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning. Statement 1038WarningTo report a gas leak, do not use a telephone in the vicinity of the leak. Statement 1039WarningThere is the danger of explosion if the battery is replaced incorrectly. Replace the battery only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions. Statement 1015
3-26Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation GuideOL-16215-10Chapter 3 Connecting the Router Connecting an xDSL LineFigure 3-22 Primary Protection Device LocationTo connect the router to a global industry standard symmetrical high-speed DSL (G.SHDSL) line, very-high-speed digital subscriber line 2 (VDSL2) port, or an ADSL2+ line, follow these steps: Step 1 Connect one end of an RJ-11 (RJ-45 on 880 E models) cable to the port on the router. See Figure 3-23.Figure 3-23 Connecting the xDSL LineStep 2 Connect the other end of the cable to the DSL wall jack.RouterHome or BusinessService Utilities Entranceor Demarcation PointNetwork Interface Box/Network Interface Device/ Station ProtectorBuilding Ground Rod connected toService entrance and Primary Protection* Alternative Underground Service EntranceNote: Primary Protection may be located Outsideor Inside of PremiseTelecom ServiceOverhead ServiceEntrance2813921G.SHDSL port, VDSL2oPOTs port, or ADSL2+ port2DSL wall jack23217521
3-27Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation GuideOL-16215-10Chapter 3 Connecting the Router Connecting Power over EthernetCaution The primary WAN port is designed for an RJ-45 connector only. Damage to the primary WAN port may occur if a non-RJ-45 connector is insertedNote The DSL line must be provisioned by your service provider and correctly configured so that the LED shows the carrier detect (CD) status. On Cisco 860VAE routers, check the DSL Link LED.Connecting Power over EthernetWarningThis unit might have more than one power supply connection. All connections must be removed to de-energize the unit. Statement 1028WarningThis product must be connected to a power-over-ethernet (PoE) IEEE 802.3af compliant power source or an IEC60950 compliant limited power source. Statement 353Figure 3-24 shows how to connect the 48-VDC Power over Ethernet (PoE) power adapter to your router. The PoE adapter provides power to ports 0 and 1 of the 4-port 10/100 FE switch on the Cisco 880 series routers and ports 0,1, 2, and 3 of the 8-port 10/100 FE switch on the Cisco 890 series routers.Note The router must also be connected to an AC power outlet through a 12-VDC adapter. To connect the router to an AC outlet, see the“Connecting the AC Adapter” section on page 3-28.Note Be sure that the internal PoE is enabled for this connection procedure to work.
3-28Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation GuideOL-16215-10Chapter 3 Connecting the Router Connecting the AC AdapterFigure 3-24 Connecting PoE for the Cisco 880 and the Cisco 890 Series RoutersThe Cisco 880 series ISRs with embedded WLAN antennas require a single external power supply: a 30-W power supply for non-POE-enabled routers or a 60-W power supply for POE-enabled routers. For the back panels of some of these routers, see Figure 1-17 and Figure 1-19.Connecting the AC AdapterWarningThe device is designed to work with TN power systems. Statement 19WarningThis product relies on the building’s installation for short-circuit (overcurrent) protection. Ensure that the protective device is rated not greater than: 120 VAC, 20 A U.S. (240 VAC, 16 to 20 A international). Statement 1005WarningThis unit might have more than one power supply connection. All connections must be removed to de-energize the unit. Statement 1028Note The Cisco 892FSP utilizes a single 4-pin power connector type. Figure 3-27 shows the pin number assignment of the Cisco 892FSP Power Adapter Connector.148-VDC PoE input jack 4AC plug2Power cord 512-VDC input power-jack plug3Power adapter—48 VDC 6Power adapter—12 VDC23199552264431
3-29Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation GuideOL-16215-10Chapter 3 Connecting the Router Connecting the AC AdapterTo connect your Cisco 860 series, Cisco 880 series, or the Cisco 890FSP ISR to an AC power outlet, follow these steps:Step 1 Connect the router to an AC power outlet as shown in Figure 3-25.To connect the Cisco 892FSP router, see Figure 3-26.Figure 3-25 Connecting the AC Adapter112-VDC plug 3Power adapter—12 VDC2Power cord 4AC plug2319961243
3-30Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation GuideOL-16215-10Chapter 3 Connecting the Router Connecting the AC AdapterFigure 3-26 Connecting the AC Adapter for the Cisco 892FSPFigure 3-27 Cisco 892FSP, 896VA, 897VA, and 898EA Power Adapter Connector Pin Assignment 7 6 GE LAN 5 49GE WAN8GE WANSFP812VD C 2.5ACONSOLEAUX RESETCisco 892FSP3437461243112-VDC plug 3Power adapter—12 VDC2Power Adapter Cord 4AC Plug284800Pin 3Pin 1 Pin 4Pin 2Pin 1 Ground Pin 3 +12 VPin 2 NC1Pin 4 NC1. NC = No Connection.
3-31Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation GuideOL-16215-10Chapter 3 Connecting the Router Connecting the AC AdapterStep 2 To secure the power cord to the router, attach the power lock clip to the power cord, slide the clip to the end of the DC plug, and secure the retaining clip into the router chassis. See Figure 3-28.Figure 3-28 Securing the Power Cord1Power lock clip 3DC plug2Power cord 4Lock holes on either side of the power connector2706594213
3-32Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation GuideOL-16215-10Chapter 3 Connecting the Router Connecting an FXS LineStep 3 Snap the latches into the holes on either side of the power connector. See Figure 3-29.Figure 3-29 Power Lock Clip Latched Into the Holes on Either Side of the Power ConnectorNote Figure 3-26 shows how to connect the AC power outlet for the Cisco 892FSP.Connecting an FXS LineUse a standard straight-through RJ-11 modular telephone cable to connect a Foreign Exchange Service (FXS) port to a telephone or fax machine. WarningThis equipment contains a ring signal generator (ringer), which is a source of hazardous voltage. Do not touch the RJ-11 (phone) port wires (conductors), the conductors of a cable connected to the RJ-11 port, or the associated circuit-board when the ringer is active. The ringer is activated by an incoming call. Statement 1042WarningHazardous network voltages are present in WAN ports regardless of whether power to the unit is OFF or ON. To avoid electric shock, use caution when working near WAN ports. When detaching cables, detach the end away from the unit first. Statement 10261Power lock clip 3Power adapter2Power cord 4AC plug2708001243
3-33Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation GuideOL-16215-10Chapter 3 Connecting the Router Connecting an FXS LineWarningFor connections outside the building where the equipment is installed, the following ports must be connected through an approved network termination unit with integral circuit protection: FXS. Statement 1044To connect the FXS line, follow these steps:Step 1 Connect one end of the straight-through RJ-11 cable to the FXS port. Figure 3-30 shows an FXS line connection.Figure 3-30 Connecting an FXS LineStep 2 Connect the other end of the cable to the RJ-11 port on the fax machine or telephone.1FXS port 3RJ-11 port2RJ-11 cableFax machineor telephone241907123
3-34Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation GuideOL-16215-10Chapter 3 Connecting the Router Connecting an FXO LineConnecting an FXO LineUse a straight-through RJ-11 cable to connect the FXO voice port to the PSTN or PBX through a telephone wall outlet.WarningHazardous network voltages are present in WAN ports regardless of whether power to the unit is OFF or ON. To avoid electric shock, use caution when working near WAN ports. When detaching cables, detach the end away from the unit first. Statement 1026To connect the FXO line, follow these steps:Step 1 Connect one end of the straight-through RJ-11 cable to the FXO port. See Figure 3-31.Figure 3-31 Connecting an FXO LineStep 2 Connect the other end of the RJ-11 cable to a telephone wall outlet. 1FXO port 3Telephone outlet2RJ-11 cable270542213
3-35Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation GuideOL-16215-10Chapter 3 Connecting the Router Connecting a Voice ISDN BRI LineNote If you have specified the use of a private line automatic ringdown (PLAR) off-premises extension (OPX) connection mode for an FXO voice port (with loop resistance less than 8000 Ohm), you must ensure that the soft-offhook option is enabled on the port. This option allows a stepped offhook resistance during seizure, which avoids overloading the circuit during offhook in the event that ringing voltage is present on the circuit at the same time as the trunk seizure. The stepped offhook resistance is initially set to 800 Ohms, then adjusts to 50 Ohms when ringing voltage is not present. To enable the soft-offhook command on the port, and to access the connection command with plar opx syntax, see the Cisco Command Lookup Tool.Connecting a Voice ISDN BRI Line Use a straight-through RJ-45 cable to connect the voice BRI port to the ISDN network through a telephone outlet or other device. Caution To prevent damage to the router, be sure to connect the BRI cable to the BRI connector only and not to any other RJ-45 connector.To connect the voice BRI line, follow these steps:Step 1 Connect one end of a straight-through RJ-45–to–RJ-45 cable to the Voice BRI port.Note When the interface is configured as NT and is connecting to a TE device, use a crossover cable. See Table A-13.
3-36Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation GuideOL-16215-10Chapter 3 Connecting the Router Connecting a Voice ISDN BRI LineFigure 3-32 shows a voice BRI line connection.Figure 3-32 Connecting a Voice BRI LineStep 2 Connect the other end of the cable to the RJ-45 telephone outlet or other device. 1Voice BRI port 3Telephone outlet2RJ-45 cable241906132
3-37Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation GuideOL-16215-10Chapter 3 Connecting the Router Connecting a Small Form-Factor Pluggable ModuleConnecting a Small Form-Factor Pluggable ModuleThis section describes how to connect and remove a small form-factor (SFP) module and contains the following information: • Safety Warnings, page 3-37 • Installing an SFP Module, page 3-38 • Removing an SFP Module, page 3-38 • Online Insertion and Removal, page 3-39Safety WarningsLaser Safety Warnings Optical SFPs use a small laser to generate the fiber-optic signal. Keep the optical transmit and receive ports covered whenever a cable is not connected to the port. WarningInvisible laser radiation may be emitted from disconnected fibers or connectors. Do not stare into beams or view directly with optical instruments. Statement 1051WarningDo not stare into the laser beam. Statement 1010WarningInvisible laser radiation present. Statement 1016WarningUltimate disposal of this product should be handled according to all national laws and regulations. Statement 1040WarningInvisible laser radiation may be emitted from the end of the unterminated fiber cable or connector. Do not view directly with optical instruments. Viewing the laser output with certain optical instruments (for example, eye loupes, magnifiers, and microscopes) within a distance of 100 mm may pose an eye hazard. Statement 1056WarningUse of controls, adjustments, or performing procedures other than those specified may result in hazardous radiation exposure. Statement 1057
3-38Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation GuideOL-16215-10Chapter 3 Connecting the Router Connecting a Small Form-Factor Pluggable ModuleInstalling an SFP ModuleTo connect and secure the SFP module, follow these steps:Step 1 Slide the SFP into the SFP port connector until it locks into position (see Figure 3-33). Tip If the SFP uses a bale-clasp latch (see Figure 3-33), the handle should be on top of the SFP module. Figure 3-33 Installing an SFP Module Caution Do not remove the optical port plugs from the SFP until you are ready to connect cabling. Step 2 Connect the network cable to the SFP module. Removing an SFP ModuleFollow these steps to remove the SFP module from a Cisco 892F series router: Step 1 Disconnect all cables from the SFP. WarningInvisible laser radiation may be emitted from disconnected fibers or connectors. Do not stare into beams or view directly with optical instruments. Statement 1051Caution The latching mechanism used on many SFPs locks the SFP into place when cables are connected. Do not pull on the cabling in an attempt to remove the SFP. Step 2 Disconnect the SFP latch. See Figure 3-34. Note SFP modules use various latch designs to secure the module in the SFP port. Latch designs are not linked to SFP model or technology type. For information on the SFP technology type and model, see the label on the side of the SFP. 94126
3-39Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation GuideOL-16215-10Chapter 3 Connecting the Router Connecting a Small Form-Factor Pluggable ModuleFigure 3-34 Figure 5-42 Disconnecting SFP Latch Mechanisms Tip Use a pen, screwdriver, or other small straight tool to gently release a bale-clasp handle if you cannot reach it with your fingers. Step 3 Grasp the SFP on both sides and remove it from the router. Online Insertion and RemovalOnline insertion and removal (OIR) of the SFP module is supported on the Cisco 892F ISRs. Note If an SFP module is inserted with auto-failover or SFP media-type already configured, the port is forced to the speed and duplex capability of the SFP. For a 100 base SFP, the speed is set to 100 and duplex can be configured to either half or full. For a 1000 base SFP, the speed is set to 1000 and duplex is set to full.1Sliding latch 3Bale-clasp latch2Swing and slide latch 4Plastic collar latch 1177221 2 3 4AB
3-40Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation GuideOL-16215-10Chapter 3 Connecting the Router Verifying ConnectionsVerifying ConnectionsTo verify that all devices are properly connected to the router, first turn on all the connected devices, then check the LEDs. To verify router operation, refer to Table 3-3.For the full LED descriptions, see the “LEDs” section on page 1-30.Ta b l e 3-3 Verifying the Router Operation Power and Link LEDs to Check Normal PatternsPower OK On when power is supplied to the router.To servers, PCs, workstations, or an external Ethernet switch connected to the LAN ports (FE01, FE1, FE2, or FE3)LAN 0, LAN 1, LAN 2, or LAN 3 On when the FE LAN port is physically connected to a server, PC, workstation, or external Ethernet switch.To FE WAN line WAN FE4 On when the WAN Ethernet carrier has detected status.Blinks when receiving or transmitting data.To xDSL2 line xDSL CD Green when the line is connected to the xDSL DSLAM3.xDSL Data Green when receiving or sending data. Blinks when line is in training mode.ATM 898EA only Green when ATM mode is selected.EFM 898EA only Green when EFM mode is selected.To ISDN line Data BRI LNK Green when the ISDN line is connected.Data BRI B1 and B2 Green when the channel is connected.3G4WWAN5Green when service is established.Slow blinking when searching for service.RSSI6Amber when service is not established.Green when signal strength is high.Off or slow blinking when signal strength is low.Fast blinking when signal strength is medium.CDMA7Green when service is established.GSM8Green when service is established.To PPP9 clients PPP Green when either a PPPoE10 or PPPoA11 client is running.To VPN12 tunnel VPN Green when a crypto session is running.
3-41Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation GuideOL-16215-10Chapter 3 Connecting the Router Verifying ConnectionsTo wireless LAN WLAN LINK Wireless LAN link status: • Green if at least one client is associated. • Off if no client is associated.WLAN 2.4 GHz Wireless LAN 2.4-GHz status: • Green when radio is connected, SSID13 is configured, signal is being transmitted, and client is associated. • Slow blinking when radio is connected, SSID is configured, and signal is being transmitted. WLAN 5.0 GHz Wireless LAN 5.0-GHz status: • Green when radio is connected, SSID is configured, signal is being transmitted, and client is associated. • Slow blinking when radio is connected, SSID is configured, and signal is being transmitted. PoE14 PoE 0 (880 and 890 series only) PoE power status: • Green when connected and powered. • Amber when there is a fault with the inline power supply.PoE 1 (880 and 890 series only)PoE 2 (890 series only)PoE 3 (890 series only)SFP15 EN Green when the interface is up.SBlinking green indicates port speed. Slow blinking for 100Base SFPs and fast blinking for 1000Base SFPs.To LAN GE/FE line (860VAE models only)LAN Blinking when there is LAN activity (traffic in either direction).Off when the link is down.Table 3-3 Verifying the Router Operation (continued)Power and Link LEDs to Check Normal Patterns
3-42Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation GuideOL-16215-10Chapter 3 Connecting the Router Verifying ConnectionsTo DSL line (860VAE models only)DSL LINK On when DSL WAN mode is selected and DSL training complete.Blinking when DSL WAN mode is selected but incomplete DSL LinkUp state such as in-training (slow initially, fast when almost connected), or controller "OFF", or no cable attached to DSL connector.Off when the device is powered off; or GE WAN mode is selected.DSL ACT On when the DSL interface is up.Blinking when there is DSL WAN activity (traffic in either direction).Faster blinking when there is heavier traffic.Off when the device is powered off or the DSL WAN interface is down.To WAN GE line (860VAE models only)GE Mode On when GE WAN mode is selected.Off when the device is powered off or when DSL WAN mode is selected.GE ACT On when the GE WAN interface is up. Blinking when there is GE WAN activity (traffic in either direction).Off when the device is powered off or when the GE WAN interface is down.1. FE = Fast Ethernet.2. xDSL = General term referring to various forms of DSL, including ADSL (asymmetric digital subscriber line), VDSL (very-high-data-rate digital subscriber line), and G.SHDSL.3. DSLAM = digital subscriber line access multiplexer.4. 3G = Third-Generation.5. WWAN = wireless WAN.6. RSSI = Received Signal Strength Indicator.7. CDMA = code division multiple access.8. GSM = Global System for Mobile Communications.9. PPP = Point-to-Point Protocol.10. PPPoE = PPP over Ethernet.11. PPPoA = PPP over ATM.12. VPN = Virtual Private Network.13. SSID = service set identifier.14. PoE = Power over Ethernet.15. SFP = small-form-factor pluggable.Table 3-3 Verifying the Router Operation (continued)Power and Link LEDs to Check Normal Patterns
CHAPTER 4-1Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation GuideOL-16215-104Initial ConfigurationThis chapter provides instructions for initial configuration of the Cisco 860 series, 880 series, and 890 series Integrated Services Routers (ISRs). For the initial configuration, we recommend using Cisco Configuration Professional (CP) Express. Cisco CP Express is a web-based graphical user interface that guides you through initial configuration. You may also initially configure your router by using the Cisco IOS command-line interface (CLI) or by using the setup command facility. To create the initial configuration, the setup command facility prompts you for basic information about your router and network. This chapter contains the following sections: • Cisco Configuration Professional Express, page 4-1 • Cisco IOS CLI, page 4-1 • Setup Command Facility, page 4-3 • Verifying the Initial Configuration, page 4-5 • Initial Configuration of the Wireless Access Point, page 4-6Note Some SKUs may not include a default configuration file. If your router does not have a default configuration file, go to the “Setup Command Facility” section on page 3 to configure the initial router settings.Cisco Configuration Professional ExpressAfter you connect the cables and power up the router, we recommend that you use the Cisco CP Express web-based application to configure the initial router settings.For instructions on how to use Cisco CP Express to configure the router see Cisco CP Express User’s Guide.Cisco IOS CLITo configure the initial router settings by using the Cisco IOS CLI, you must set up a console connection. For instructions on how to set up a console connection, see the “Connecting a Terminal or PC to the Console Port” section on page 3-9.
4-2Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation GuideOL-16215-10Chapter 4 Initial Configuration Cisco IOS CLITo configure the initial router settings using the Cisco IOS CLI, follow these steps:Step 1 Set up a console connection to your router. The following message is displayed:...router con0 is now availableStep 2 Press Return. The following message is displayed:Cisco Configuration Professional Express (Cisco CP Express) is installed on this device. This feature requires the one-time use of the username "username1" with the password "password1." The default username and password have a privilege level of 15.Please change these publicly known initial credentials using Cisco CP Express or the Cisco IOS CLI.Here are the Cisco IOS commands.username <myuser> privilege 15 secret 0 <mypassword>no username username1Replace <myuser> and <mypassword> with the username and password you want to use.For more information about Cisco CP please follow the instructions in the QUICK START GUIDE for your router......User Access VerificationUsername:Step 3 Enter the username username1, and press Return or Enter. The following prompt is displayed:Password:Step 4 Enter the password password1, and press Return or Enter. The following prompt is displayed:Router#A message is displayed that is similar to the first warning message. The message directs you to change the username and password.You are now in privileged EXEC mode.Note You must change the username and password before you log off the router. You cannot use the username username1 or password password1 after you log off from this session.Step 5 Enter configuration mode using the following commands.Router#Router#config tRouter(config)# Router(config)#username username privilege 15 secret 0 passwordStep 6 To change the username and password, enter the following at the prompt:username username privilege 15 secret 0 passwordThe username and password are the username and password that you determine.To continue using the Cisco IOS CLI for initial configuration, see the applicable configuration procedures in Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Software Configuration Guide.
4-3Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation GuideOL-16215-10Chapter 4 Initial Configuration Setup Command FacilityNote Save your configuration changes regularly to avoid losing them during resets, power cycles, or power outages. Use the copy running-config startup-config command at the privileged EXEC mode prompt (Router#) to save the configuration to NVRAM.Step 7 Verify the initial configuration. See the “Verifying the Initial Configuration” section on page 4-5.Setup Command FacilityThe setup command facility guides you through the configuration process by prompting you for the specific information that is needed to configure your system. Use the setup command facility to configure a hostname for the router, to set passwords, and to configure an interface for communication with the management network.To use the setup command facility, you must set up a console connection with the router and enter the privileged EXEC mode. Note For instructions on how to set up a console connection, see the “Connecting a Terminal or PC to the Console Port” section on page 3-9.To configure the initial router settings by using the setup command facility, follow these steps:Step 1 Set up a console connection to your router, and enter privileged EXEC mode. For instructions on how to enter privileged EXEC mode, see Step 1 through Step 4 in the “Cisco IOS CLI” section on page 4-1.Step 2 In privileged EXEC mode, at the prompt, enter setup. yourname# setupThe following message is displayed:--- System Configuration Dialog ---Continue with configuration dialog? [yes/no]:You are now in the setup command facility.The prompts in the setup command facility vary, depending on your router model, on the installed interface modules, and on the software image. The following steps and the user entries (in bold) are shown as examples only.Note If you make a mistake while using the setup command facility, you can exit and run the setup command facility again. Press Ctrl-C, and enter the setup command at the privileged EXEC mode prompt (Router#). For more information on using the setup command facility, see “The Setup Command” chapter in Cisco IOS Configuration Fundamentals Command Reference, Release 12.2T.Step 3 To proceed using the setup command facility, enter yes.Continue with configuration dialog? [yes/no]: yes
4-4Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation GuideOL-16215-10Chapter 4 Initial Configuration Setup Command FacilityStep 4 When the following messages appear, enter yes to enter basic management setup.At any point you may enter a question mark '?' for help.Use ctrl-c to abort configuration dialog at any prompt.Default settings are in square brackets '[]'.Basic management setup configures only enough connectivityfor management of the system, extended setup will ask youto configure each interface on the systemWould you like to enter basic management setup? [yes/no]: yesStep 5 Enter a hostname for the router (this example uses Router).Configuring global parameters:Enter host name [Router]: RouterStep 6 Enter an enable secret password. This password is encrypted (more secure) and cannot be seen when viewing the configuration.The enable secret is a password used to protect access toprivileged EXEC and configuration modes. This password, afterentered, becomes encrypted in the configuration.Enter enable secret: xxxxxxStep 7 Enter an enable password that is different from the enable secret password. This password is not encrypted (less secure) and can be seen when viewing the configuration.The enable password is used when you do not specify anenable secret password, with some older software versions, andsome boot images.Enter enable password: xxxxxxStep 8 Enter the virtual terminal password, which prevents unauthenticated access to the router through ports other than the console port.The virtual terminal password is used to protectaccess to the router over a network interface.Enter virtual terminal password: xxxxxxStep 9 Respond to the following prompts as appropriate for your network.Configure SNMP Network Management? [yes]: Community string [public]:A summary of the available interfaces is displayed.Step 10 Choose one of the available interfaces for connecting the router to the management network.Enter interface name used to connect to themanagement network from the above interface summary: fastethernet4Step 11 Respond to the following prompts as appropriate for your network.Configuring interface FastEthernet4:Use the 100 Base-TX (RJ-45) connector? [yes]: yesOperate in full-duplex mode? [no]: yesConfigure IP on this interface? [yes]: yes IP address for this interface: 172.1.2.3 Subnet mask for this interface [255.255.0.0] : 255.255.0.0 Class B network is 172.1.0.0, 26 subnet bits; mask is /16
4-5Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation GuideOL-16215-10Chapter 4 Initial Configuration Verifying the Initial ConfigurationThe configuration is displayed:The following configuration command script was created:hostname Routerenable secret 5 $1$D5P6$PYx41/lQIASK.HcSbfO5q1enable password xxxxxxline vty 0 4password xxxxxxsnmp-server community public!no ip routing!interface FastEthernet4no shutdownspeed 100duplex autoip address 172.1.2.3 255.255.0.0!Step 12 Respond to the following prompts. Enter 2 to save the initial configuration.[0] Go to the IOS command prompt without saving this config.[1] Return back to the setup without saving this config.[2] Save this configuration to nvram and exit.Enter your selection [2]: 2Building configuration...Use the enabled mode 'configure' command to modify this configuration.Press RETURN to get started! RETURNThe user prompt is displayed.Router>Step 13 Verify the initial configuration. See the “Verifying the Initial Configuration” section on page 4-5 for verification procedures.After the initial configuration file is created, you can use the Cisco IOS CLI to perform additional configuration. Verifying the Initial ConfigurationTo verify that the new interfaces are operating correctly, perform the following tests: • To verify that the interfaces and line protocol are in the correct state—up or down—enter the show interfaces command. • To display a summary status of the interfaces configured for IP, enter the show ip interface brief command. • To verify that you configured the correct hostname and password, enter the show configuration command.After you complete and verify the initial configuration, you can configure your Cisco router for specific functions.
4-6Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation GuideOL-16215-10Chapter 4 Initial Configuration Initial Configuration of the Wireless Access PointInitial Configuration of the Wireless Access PointThe embedded wireless access point (AP) runs its own IOS. You can initially configure the embedded wireless AP by using one of the following methods: • Cisco Configuration Professional (CP) Express • Setup command facility on the embedded wireless deviceFor information on how to do basic wireless configuration on your router see the “Basic Wireless Device” chapter of the Cisco 860 Series, Cisco 880, and Cisco 890 Series Integrated Services Routers Software Configuration Guide.
A-1Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation GuideOL-16215-10APPENDIXATechnical SpecificationsThis appendix provides router, port, and cabling specifications for the Cisco 860 series, Cisco 880 series, and Cisco 890 series Integrated Services Routers (ISRs). It contains the following sections: • Router Specifications, page A-2 • Wireless Access Point, page A-3 • FE and GE Port Pinouts, page A-3 • Console and Auxiliary Port Connector Pinouts, page A-4 • FXS and FXO Port Connector Pinouts, page A-5 • VDSL2 Port Connector Pinouts, page A-5 • ADSL2+ Port Connector Pinouts, page A-5 • V.92 Port Connector Pinouts, page A-6 • G.SHDSL Port Connector Pinouts, page A-6 • Data BRI Port Connector Pinouts, page A-7 • Voice ISDN BRI Interface Pin Numbers and Functions, page A-7 • SFP Port Connector Pinouts, page A-8 • Cable Specifications, page A-8WarningUltimate disposal of this product should be handled according to all national laws and regulations. Statement 1040Note For compliance and safety information, see Regulatory Compliance and Safety Information Roadmap that was shipped with the router and Regulatory Compliance and Safety Information for Cisco 800 Series and SOHO Series Routers.Note The product has some color variation on the Power Pin. This will not impact product performance or reliability.
A-2Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation GuideOL-16215-10Appendix A Technical Specifications Router SpecificationsRouter SpecificationsTable A-1 lists the system specifications for the routers. Ta b l e A-1 Router Specifications DescriptionDesign Specification (all models except Cisco 860VAE series)Design Specification Cisco 860VAE seriesPhysical DimensionsDimensions with antenna and rubber feet (H x W x D) 1.9 x 12.8 x 10.4 in. 1.75 x 9.5 x 9 in.Weight (not including desktop power supply)5.5 lb (2.5 kg), maximum 3 lb (1.4 kg) The total weight depends on customer-selected options.Environmental Operating RangesNonoperating temperature –4 to 149°F (–20 to 65°C) –4 to 149°F (–20 to 65°C)Nonoperating humidity 5 to 95% relative humidity 5 to 95% relative humidityNonoperating altitude 0 to 15,000 ft (4570 m) 0 to 15,000 ft (4570 m)Operating temperature 32 to 104°F (0 to 40°C) 32 to 104°F (0 to 40°C)Operating humidity 10 to 85% relative humidity 10 to 85% relative humidityOperating altitude 0 to 10,000 ft (3000 m) 0 to 10,000 ft (3000 m)AcousticAcoustic: Sound Pressure (Typical/Maximum) Low speed 31.4 dBa High speed 44.1 dBa N/A, no fanAcoustic: Sound Power (Typical/Maximum) Low speed 38.9 dBA High speed 51.7 dBa N/A, no fanRouter Power AdapterInput voltage 100 to 240 VAC Nominal 100 to 240 VAC NominalInput frequency 47 to 63 Hz 47 to 63 Hz Power output 60 W, maximum 30 W, maximumOutput voltages +12 VDC +12 VDCInline Power-over-Ethernet AdapterInput voltage 85 to 264 VAC not supportedInput frequency 47 to 63 HzPower output 80 W, maximumOutput voltage –48 VDC
A-3Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation GuideOL-16215-10Appendix A Technical Specifications Wireless Access PointWireless Access PointTable A-2 lists the specifications for the wireless access point (AP). FE and GE Port PinoutsTable A-3 describes the RJ-45 connector pinouts for Fast Ethernet (FE) ports with Power over Ethernet (PoE). Some models support PoE using an optional module, and some models do not support PoE. For ports that do not support PoE, pins 4, 5, 7, and 8 are not connected. • Cisco 860VAE and 860VAE-K9 ISRs do not support PoE. • Cisco 880 series ISRs can include an optional PoE module that provides power to 802.3af-compliant devices connected to FE ports 0 and 1. • Cisco 890 series ISRs can include an optional PoE module that provides power to 802.3af-compliant devices connected to FE ports 0, 1, 2, and 3.Ta b l e A-2 Wireless Access Point Specifications Description Design SpecificationRadio technology IEEE 802.11n draft 2.0 standard compliant. 2x3 MIMO1 radio. Backward compatible with 802.11b/g and 802.11a (Cisco 890 series routers).1. MIMO = Multiple Input/Multiple Output.Operating frequency Cisco 860 series and 880 series ISRs2.4-GHz radio bandCisco 890 series ISRs2.4 and 5-GH radio bandsChannels Country-specific 20 and 40 MHzPHY Data rate 802.11b up to 11 Mb/s802.11g up to 54 Mb/s 802.11n up to 300 Mb/sTa b l e A-3 Ethernet FE LAN Port Pinouts Pin Function1RX+1 2RX–3TX+2 4PoE—optional 5PoE—optional 6TX–7PoE—optional 8PoE—optional
A-4Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation GuideOL-16215-10Appendix A Technical Specifications Console and Auxiliary Port Connector PinoutsTable A-4 describes the RJ-45 connector pinouts for the Gigabit Ethernet (GE) ports of the Cisco 860VAE and 860VAE-K9 ISRs.Console and Auxiliary Port Connector PinoutsTable A-5 lists the pinouts for the console and auxiliary port connectors.1. RX = Receive2. TX = TransmitTa b l e A-4 Ethernet GE Port Pinouts PinGE Signal(LAN and WAN)1Tx A+11. TX = Transmit2Tx A-3Rx B+22. RX = Receive4Tx C+5Tx C-6Rx B-7Rx D+8Rx D-Ta b l e A-5 Console and Auxiliary Port Connector Pinouts RJ-45 Pin Function1RTS2DTR3TXD4GND5GND6RXD7DSR8CTS
A-5Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation GuideOL-16215-10Appendix A Technical Specifications FXS and FXO Port Connector PinoutsFXS and FXO Port Connector PinoutsTable A-6 lists the FXS and FXO connector pinouts.VDSL2 Port Connector PinoutsTable A-7 lists the VDSL2 connector pinouts.ADSL2+ Port Connector PinoutsTable A-8 lists the ADSL2+ connector pinouts.Ta b l e A-6 FXS and FXO Connector Pinouts (RJ-11-to-RJ-45) Pin Signal1NC2NC3TIP4RING5NC6NCTa b l e A-7 VDSL2 Connector Pinouts (RJ-11-to-RJ-45) RJ-11 Pin Function1Unused2Unused3TIP4RING5Unused6UnusedTa b l e A-8 ADSL2+ Connector Pinouts (RJ-11) RJ-11 Pin Function1Unused2Unused3TIP4RING5Unused6Unused
A-6Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation GuideOL-16215-10Appendix A Technical Specifications V.92 Port Connector PinoutsV.92 Port Connector PinoutsTable A-9 lists the V.92 connector pinouts.G.SHDSL Port Connector PinoutsTable A-10 lists the pinouts for the symmetrical high-speed DSL (G.SHDSL) WAN port for two-pair products, including the following router model(s): • C888Table A-11 lists the pinouts for the symmetrical high-speed DSL (G..SHDSL) WAN port for four-pair products, including the following router models: • C888E • C888EW • C888EATa b l e A-9 V.92 Connector Pinouts (RJ-11-to-RJ-45) RJ-11 Pin Function1Unused2Unused3TIP4RING5Unused6UnusedTa b l e A-10 G.SHDSL WAN Port Pinouts for Two-Pair ProductsPin Function1Unused2TIP (Port1)3TIP (Port0)4RING (Port0)5RING (Port1)6UnusedTa b l e A-11 G.SHDSL WAN Port Pinouts for Four-Pair Products Pin Function1TIP (Port1)2RING (Port1)3TIP (Port2)

Navigation menu