GemTek Technology A910910AB Wireless Dual-Band Access Point User Manual WX 5520A revised user s Manual

Gemtek Technology Co., Ltd. Wireless Dual-Band Access Point WX 5520A revised user s Manual

Contents

Users Manual Revised

WX-5520ADual Band WLAN Access PointUser's Manual Oct. 15, 2002 (Draft 1.0)Gemtek Technology Co., Ltd.
WX-5520A Dual Band Access PointWireless Broadband Anywhere 1CONTENTSIntroduction ............................................................................ 2 Hardware Installation ............................................................................. 4 WX-5520A AP Default Settings ...………………………………………..5 Web Management Settings …………………………………………6 Start - Up & Log in ……………………………………………………….6 Main Page …………………………………………………………………7 Setup …………...………………………………………………………….8 Password…………. … ..……………………………………………………9 Firmware Upgrade ………………………………………………………..10 Security …………………………………………………………………11 Access Control……….. …………………………………………………..12 Advance Setup …………………………………………………13 About ………………………………………………………………………14 Troubleshooting ……………………………………………………………15 Technical Specifications ……………………………………………………17Federal Communication Commission Interference Statement …………19 R&TTE Compliance Statement …………………………………………….….20
WX-5520A Dual Band Access PointWireless Broadband Anywhere 2IntroductionThank you for purchasing your WX-5520A Dual Band Wireless Access Point.This user guide will assist you with the installation procedure.The package you have received should contain the following items:• WX-5520A Dual Band Wireless AP• User Guide• Power Supply / Cord• Ethernet CableNote: if anything is missing, please contact your vendor
WX-5520A Dual Band Access PointWireless Broadband Anywhere 3Safety NotificationYour Wireless AP should be placed in a safe and secure location. To ensure properoperation, please keep the unit away from water and other damaging elements.§ Please read the user manual thoroughly before you install the device.§ The device should only be repaired by authorized and qualified personnel.§ Please do not try to open or repair the device yourself.§ Do not place the device in a damp or humid location, i.e. a bathroom.§ The device should be placed in a sheltered and non-slip location within a temperaturerange of +5 to +40 Celsius degree.§ Please do not expose the device to direct sunlight or other heat sources. The housingand electronic components may be damaged by direct sunlight or heat sources.
WX-5520A Dual Band Access PointWireless Broadband Anywhere 4Hardware InstallationFront PanelThe front panel provides LED’s for device status. Refer to the followingtable for the meaning of each feature.LED STATUS DescriptionPower Off No Power　On Power onStatus Blink 1. Power up 2. firmware upgrade　Off no Ethernet link detectedEthernet Green On 10/100Mbps Fast Ethernet link detected. No activity.　Green Blink Indicates data traffic on the 10/100 Mbps LAN11a Blink Indicates the device is linking or active data through wireless links11b Blink Indicates the device is linking or active data through wireless linksRear PanelThe rear panel features 1 LAN port and Factory Reset button. Refer to thefollowing table for the meaning of each feature.Power(DC 5v) Used to connect to the power outlet. Only use the power adapterprovided with the device. Use of an unauthorized power adaptermay cause damage to your device and violate your warranty.Reset Reset the configuration to default settings.There are two ways to Reset to factory defaults of the Access Point.Briefly press the Reset Button for approximately ten seconds, or usethe setup tab of the Web-Based Management Utility.LAN The RJ-45 Ethernet ports used to connect your PC, hub, switch orEthernet network.
WX-5520A Dual Band Access PointWireless Broadband Anywhere 5WX-5520A AP Default Settings The default settings are shown following.User Name adminPassword 1234AP Router IP Address 192.168.5.1AP Router Subnet Mask 255.255.255.0RF ESSID Wireless11a RF Channel 5211b RF Channel 6RF Roaming EnabledEncryption DisabledDHCP client Disabled
WX-5520A Dual Band Access PointWireless Broadband Anywhere 6Web Management Settings TURN ON POWER SUPPLYQuick power cycle can caused system corruption. When power on, be careful not to shutdown in about 5 seconds, because data is writing to the flash.START -UP & LOG INIn order to configure the WX-5520A Wireless AP, please use your web browser(Microsoft Internet Explorer or Netscape) and manually input 192.168.5.1 into the addressbox (as shown below) and press Enter key.In order to configure the WX-5520A Wireless AP, please input the user-name into theUser Name box. Enter the password into the Password box and press the OK button. Thedefault User Name is admin, and the default password is 1234.Once you have logged-in as administrator, it is a good idea to change theadministrator password to ensure a secure connection to the Wireless AP.
WX-5520A Dual Band Access PointWireless Broadband Anywhere 7MAKE CORRECT NETWORK SETTINGS OF YOUR COMPUTERTo change the configuration, use Internet Explorer (IE) or Netscape Communicator toconnect the WEB management 192.168.5.1.Main PageHere allow user to configure basic network settings.
WX-5520A Dual Band Access PointWireless Broadband Anywhere 8Setup pageThe Setup page allow user to configure basic settings. Enter your wireless network’s SSID,select the channel at which the network broadcasts its wireless signal, and enter IP addressand subnet mask for the Access Point. Press Apply & Restart button to save the settings.IP Address: This IP address must be unique to your network. (The default IP address of192.168.5.1)Subnet Mask: The Access Point’s Subnet Mask must be same as your Ethernet network.SSID: The service set identifier ( SSID ) or network name. It is case sensitive and must notexceed 32 characters, which may be any keyboard character. You shall have selected thesame SSID for all the APs that will be communicating with mobile wireless stations.
WX-5520A Dual Band Access PointWireless Broadband Anywhere 9Channel: Select the appropriate channel from the list provided to correspond with yournetwork settings. You shall assign a different channel for each AP to avoid signalinterference.Data Rates: The basic transfer rates should be set depending on the speed of your wirelessnetwork.PasswordThis page allows you to change the Access Point’s password.Changing the password for the Access Point is as easy as typing the password into theNew Password field. Then, type it again into the Retype new password field to confirm.Click the Apply & Restart button to save the setting.Use the default password when you first open the configuration pages, and thenimmediately change the password to avoid a security breach.
WX-5520A Dual Band Access PointWireless Broadband Anywhere 10Firmware UpgradeUser may download the latest firmware from your vendor’s website and store it in localdrive.Find the firmware from local drive and press the Upgrade & Restart button.Restore DefaultPress OK button will make the AP reset to factory default settings.
WX-5520A Dual Band Access PointWireless Broadband Anywhere 11SecurityAuthentication Type:Open System: The Authentication Type default is set to Open System.It is recommended that you use the default setting.Shared Key: Shared Key is when both the sender and the recipient share a secret key. Allpoints on your network must use the same authentication type.WEP: The WEP Encryption method is Disable by default. To enable WEP, click theEnable radio button.From the pull-down menu at the top of the screen, select 64-bit, 128-bit, or 152 bitencryption. The Encryption key is in Hexadecimal format. Hexadecimal characters on yourkeyboard are the letters “A-F” and the numbers “ 0- 9”. Click the Apply & Restart buttonto save the setting.
WX-5520A Dual Band Access PointWireless Broadband Anywhere 12Access ControlThe Access Control tab, allows you to block or allow certain computers by their MACAddress.To enable filtering of computers by their MAC Addresses, click the Enable radio button.Enter MAC Address and click Add button.Click Delete button if you wish to remove the MAC address from the list.To disable this feature, click the radio button by Disable.Click Apply & Restart button to save the setting.
WX-5520A Dual Band Access PointWireless Broadband Anywhere 13Advance SetupBeacon Interval: This value indicates the frequency interval of the beacon.A beacon is a packet broadcast by the Access Point to keep the network synchronized.A beacon includes the wireless LAN service area, the AP address, the Broadcastdestination addresses, a time stamp, Delivery Traffic Indicator Maps, and the TrafficIndicator Message (TIM).RTS Threshold: This value should remain at its default setting of 2,346.Should you encounter inconsistent data flow, only minor modifications are recommended.Fragmentation Threshold: This specifies the maximum size a data packet will be beforesplitting and creating a new packet and should remain at its default setting of 2,346. Asmaller setting means smaller packets, which will create more packets for eachtransmission. Only minor modifications of this value are recommended.DTIM Interval: This value indicates the interval of the Delivery TrafficIndication Message (DTIM). A DTIM field is a countdown field informing clients of the
WX-5520A Dual Band Access PointWireless Broadband Anywhere 14next window for listening to broadcast and multicast messages.When the Access Point has buffered broadcast or multicast messages for associated clients,it sends the next DTIM with a DTIM Interval value.Access Point Clients hear the beacons and awaken to receive the broadcast and multicastmessages.Preamble Type: The preamble defines the length of the CRC block for communicationbetween the Access Point and a roaming Network Card. (High network traffic areas shoulduse the shorter preamble type.) Select the appropriate preamble type and click the Applybutton to set it. All wireless points (nodes) on your network should use the same preambletype.AboutThe page describes the product briefly.
WX-5520A Dual Band Access PointWireless Broadband Anywhere 15TroubleshootingBasic FunctionsMy Wireless AP will not turn on. No LED’s light up.Cause:§ The power is not connected.Resolution:§ Connect the power adapter to your AP and plug it into the power outlet.Note: Only use the power adapter provided with your AP. Using any other adapter maydamage your SOHO AP Router.LAN Connection ProblemsI can’t access my SOHO AP Router.Cause:§ The unit is not powered on.§ There is not a network connection.§ The computer you are using does not have a compatible IP Address.Resolution:§ Make sure your AP is powered on.§ Make sure that your computer has a compatible IP Address. Be sure that the IP Addressused on your computer is set to the same subnet as the AP. For example, if the AP isset to 192.168.5.250, change the IP address of your computer to 192.168.5.15 oranother unique IP Address that corresponds to the 192.168.5.X subnet. Use the Reset button located on the rear of the AP to revert to the default settings.I can’t connect to other computers on my LAN.Cause:§ The IP Addresses of the computers are not set correctly.§ Network cables are not connected properly.§ Windows network settings are not set correctly.
WX-5520A Dual Band Access PointWireless Broadband Anywhere 16Resolution:§ Make sure that each computer has a unique IP Address. If using DHCP through the AP ,makes sure that each computer is set to “Obtain an IP Address automatically” andrestart the computer.§ Make sure that the Link LED is on. If it is not, try a different network cable.§ Check each computer for correct network settings.Wireless TroubleshootingI can’t access the Wireless AP from a wireless network cardCause:§ Out of range.§ IP Address is not set correctly.Resolution:§ Make sure that the Mode, SSID, Channel and encryption settings are set the same oneach wireless adapter.§ Make sure that your computer is within range and free from any strong electricaldevices that may cause interference.§ Check your IP Address to make sure that it is compatible with the Wireless AP.Performing a Factory ResetFollow these steps to perform a Factory Reset using the Reset button on the back of theWireless AP.1. With the unit on, press and hold the Reset button with a pen or paper clip.2. Hold the reset button for about 5 or 6 seconds until the Status LED on the frontpanel blinks very quickly and then release.3. Wait a few seconds for the AP to reboot using default settings.A Factory Reset can also be performed through the web configuration interface. Followthese steps to perform a factory reset using the web configuration interface.1. Log-in to the Wireless AP web configuration interface.2. Click on Restore Default.3. You will be asked if you want to restore to default settings. Click OK to restore settings to default configuration or click Cancel to discard any changes.
WX-5520A Dual Band Access PointWireless Broadband Anywhere 17Technical SpecificationsStandards: IEEE 802.3 10BASE-T Ethernet IEEE 802.3u 100BASE-TX Fast Ethernet IEEE 802.11b IEEE802.11aProtocols Supported: TCP IP IPX DHCP ClientManagement: Web-BasedPorts: LAN: 10BASE-T/100BASE-TX Fast EthernetWireless AP SpecificationsGeneral Wireless Specifications: IEEE 802.11b /11a Wireless LAN, Wi-Fi CompatibleAccess Point Frequency Band: 5GHz (subject to local regulation) 2.4 ~ 2.4835 GHz (subject to local regulation)Access Point Number of Channel:11a: USA domain 8 ( 36,40,44,48,52,52,60,64)11b: USA & Canada: 11 (1- 11) Most European: 13 (1-13) France : 4 (10-13) Japan : 14 (1-14)
WX-5520A Dual Band Access PointWireless Broadband Anywhere 18Access Point Data Rate:11a : 6,9,12,18,24,36,48,54 Mbps. Turbo: 72 Mbps11b: 11 Mbps 5.5 Mbps 2 Mbps 1 MbpsData encryption: 64/128/152 bit WEPPower Specifications :DC power supply Input: DC 100-250 50-60 Hz 1A Output: 5V DC 2A
WX-5520A Dual Band Access PointWireless Broadband Anywhere 19Federal Communication Commission Interference StatementThis equipment has been tested and found to comply with the limits for a Class Bdigital device, pursuant to Part 15 of the FCC Rules. These limits are designed toprovide reasonable protection against harmful interference in a residentialinstallation. This equipment generates, uses and can radiate radio frequencyenergy and, if not installed and used in accordance with the instructions, maycause harmful interference to radio communications. However, there is noguarantee that interference will not occur in a particular installation. If thisequipment does cause harmful interference to radio or television reception, whichcan be determined by turning the equipment off and on, the user is encouraged totry to correct the interference by one of the following measures:-Reorient or relocate the receiving antenna.-Increase the separation between the equipment and receiver.-Connect the equipment into an outlet on a circuit different from thatto which the receiver is connected.-Consult the dealer or an experienced radio/TV technician for help.FCC Caution: To assure continued compliance, (example - use only shieldedinterface cables when connecting to computer or peripheral devices). Anychanges or modifications not expressly approved by the party responsible forcompliance could void the user's authority to operate this equipment.This device complies with Part 15 of the FCC Rules. Operation is subjectto the following two conditions: (1) This device may not cause harmfulinterference, and (2) this device must accept any interference received,including interference that may cause undesired operation.IMPORTANT NOTE:FCC RF Radiation Exposure Statement:This equipment complies with FCC RF radiation exposure limits set forth for anuncontrolled environment. This equipment should be installed and operated with aminimum distance of 20 centimeters between the radiator and your body. Thisdevice must not be co-located or operating in conjunction with any other antenna ortransmitter other than those contained within this device.The UNII device applying frequency band 5.15-5.25 GHz is restricted to be indooruse only, comply with the rule of FCC15.407(e).
WX-5520A Dual Band Access PointWireless Broadband Anywhere 20R&TTE Compliance StatementThis equipment complies with all the requirements of the DIRECTIVE 1999/5/ECOF THE EUROPEAN PARLIAMENT AND THE COUNCIL of 9 March 1999 on radioequipment and telecommunication terminal Equipment and the mutual recognitionof their conformity (R&TTE).The R&TTE Directive repeals and replaces in the directive 98/13/EEC(Telecommunications Terminal Equipment and Satellite Earth Station Equipment)As of April 8, 2000 .SafetyThis equipment is designed with the utmost care for the safety of those who installand use it. However, special attention must be paid to the dangers of electric shockand static electricity when working with electrical equipment. All guidelines of thismanual and of the computer manufacturer must therefore be allowed at all times toensure the safe use of the equipment.EU Countries intended for useThe ETSI version of this device is intended for home and office use in Austria,Belgium, Denmark, Finland, France (with Frequency channel restrictions),Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway,Portugal, Spain, Sweden, Switzerland and United Kingdom.The ETSI version of this device is also authorized for use in EFTA member statesIceland, Liechtenstein, Norway and Switzerland.EU Countries Not intended for useNone.Potential restrictive useFrance: Only channels 10,11,12, and13

Navigation menu