Garmin 03198 Digital Transmission System 2412-2462 MHz User Manual

Garmin International Inc Digital Transmission System 2412-2462 MHz

User Manual

ECHOMAP™ 40/60/70/90 SERIESOwner’s Manual
© 2017 Garmin Ltd. or its subsidiariesAll rights reserved. Under the copyright laws, this manual may not be copied, in whole or in part, without the written consent of Garmin. Garmin reserves the right to change or improve its products and to make changes in the content of this manual without obligation to notify any person or organization of such changes or improvements. Go to www.garmin.com for current updates and supplemental information concerning the use of this product.Garmin®, the Garmin logo, BlueChart®, g2 Vision®, FUSION®, and Ultrascroll® are trademarks of Garmin Ltd. or its subsidiaries, registered in the USA and other countries. ActiveCaptain™, ECHOMAP™, FUSION-Link™, Garmin ClearVü™, Garmin Connect™, Garmin Express™, Garmin Quickdraw™, GXM™, HomePort™, OneChart™, and Panoptix™ are trademarks of Garmin Ltd. or its subsidiaries. These trademarks may not be used without the express permission of Garmin.The Bluetooth® word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Garmin is under license.NMEA®, NMEA 2000®, and the NMEA 2000 logo are registered trademarks of the National Marine Electronics Association. microSD® and the microSD logo are trademarks of SD-3C, LLC. SiriusXM® is a registered trademark of SiriusXM Radio Inc. Wi‑Fi® is a registered mark of Wi-Fi Alliance Corporation. Windows® is a registered trademark of Microsoft Corporation in the United States and other countries. All other trademarks and copyrights are the property of their respective owners.
Table of ContentsIntroduction.....................................................................1ECHOMAP Plus 40 Device View................................................ 1Device Keys........................................................................... 1ECHOMAP Plus 60 Front View.................................................. 1Device Keys........................................................................... 1ECHOMAP Plus 70/90 Front View............................................. 1Device Keys........................................................................... 2Assigning a Shortcut Key....................................................... 2Getting the Owner's Manual....................................................... 2Acquiring GPS Satellite Signals..................................................2Selecting the GPS Source..................................................... 2Inserting Memory Cards............................................................. 2Customizing the Chartplotter........................................ 2Customizing the Home Screen................................................... 2Customizing Pages..................................................................... 2Customizing a Combination Page..........................................2Creating a New Combination Page with the ECHOMAP Plus 70/90...................................................................................... 2Creating a New Combination Page with the ECHOMAP Plus 60........................................................................................... 2Creating a New Combination Page with the ECHOMAP Plus 40........................................................................................... 3Setting the Vessel Type.............................................................. 3Adjusting the Backlight............................................................... 3Adjusting the Color Mode........................................................... 3ActiveCaptain App......................................................... 3ActiveCaptain Roles................................................................... 3Getting Started with the ActiveCaptain App............................... 3Receiving Smart Notifications..................................................... 4Updating Software with the ActiveCaptain App.......................... 4Updating Charts with ActiveCaptain........................................... 4Charts and 3D Chart Views........................................... 4Navigation Chart and Fishing Chart........................................... 4Zooming In and Out of the Chart........................................... 5Panning the Chart with the Keys........................................... 5Selecting an Item on the Map Using the Device Keys........... 5Chart Symbols....................................................................... 5Measuring a Distance on the Chart....................................... 5Creating a Waypoint on the Chart..........................................5Navigating to a Point on the Chart......................................... 5Viewing Location and Object Information on a Chart............ 5Viewing Details about Navaids.............................................. 5Heading Line and Angle Markers.......................................... 5Setting the Heading and Course Over Ground Lines....... 6Turning on Angle Markers................................................. 6Premium Charts.......................................................................... 6Viewing Tide Station Information........................................... 6Animated Tide and Current Indicators.............................. 6Showing Tides and Current Indicators.............................. 6Showing Satellite Imagery on the Navigation Chart.............. 6Viewing Aerial Photos of Landmarks..................................... 7Automatic Identification System..................................................7AIS Targeting Symbols.......................................................... 7Heading and Projected Course of Activated AIS Targets...... 7Showing AIS Vessels on a Chart or 3D Chart View.............. 7Activating a Target for an AIS Vessel.................................... 8Viewing Information about a Targeted AIS Vessel........... 8Deactivating a Target for an AIS Vessel........................... 8Viewing a List of AIS Threats................................................. 8Setting the Safe-Zone Collision Alarm................................... 8AIS Distress Signals.............................................................. 8Navigating to a Distress Signal Transmission................... 8AIS Distress Signal Device Targeting Symbols................ 8Enabling AIS Transmission Test Alerts............................. 8Turning Off AIS Reception..................................................... 8Chart and 3D Chart View Settings.............................................. 8Navigation and Fishing Chart Setup...................................... 8Chart Appearance Settings............................................... 9Overlay Numbers Settings................................................ 9Showing a Navigation Inset...............................................9Setting the Heading and Course Over Ground Lines....... 9Waypoints and Tracks Settings on the Charts and Chart Views................................................................................... 10Other Vessels Settings on the Charts and Chart Views...... 10AIS Display Settings........................................................10Laylines Settings.................................................................. 10Fish Eye 3D Settings........................................................... 10Supported Maps....................................................................... 10Garmin Quickdraw Contours Mapping....................... 10Mapping a Body of Water Using the Garmin Quickdraw Contours Feature...................................................................... 11Adding a Label to a Garmin Quickdraw Contours Map............ 11Garmin Quickdraw Community................................................. 11Connecting to the Garmin Quickdraw Community with ActiveCaptain....................................................................... 11Downloading Garmin Quickdraw Community Maps Using ActiveCaptain.................................................................. 11Sharing Your Garmin Quickdraw Contours Maps with the Garmin Quickdraw Community Using ActiveCaptain...... 11Connecting to the Garmin Quickdraw Community with Garmin Connect................................................................... 11Sharing Your Garmin Quickdraw Contours Maps with the Garmin Quickdraw Community Using Garmin Connect.. 11Downloading Garmin Quickdraw Community Maps Using Garmin Connect.............................................................. 11Garmin Quickdraw Contours Settings...................................... 12Depth Range Shading......................................................... 12Navigation with a Chartplotter.................................... 12Basic Navigation Questions...................................................... 13Destinations.............................................................................. 13Searching for a Destination by Name.................................. 13Selecting a Destination Using the Navigation Chart............ 13Searching for Destination Using User Data......................... 13Searching for a Marine Services Destination....................... 13Courses.................................................................................... 13Setting and Following a Direct Course Using Go To........... 13Stopping Navigation................................................................. 14Waypoints................................................................................. 14Marking Your Present Location as a Waypoint.................... 14Creating a Waypoint at a Different Location........................ 14Marking an MOB or SOS Location.......................................14Viewing a List of all Waypoints............................................ 14Editing a Saved Waypoint.................................................... 14Browsing for and Navigating to a Saved Waypoint.............. 14Deleting a Waypoint or an MOB.......................................... 14Deleting All Waypoints......................................................... 14Routes...................................................................................... 14Creating and Navigating a Route From Your Present Location............................................................................... 14Creating and Saving a Route............................................... 14Viewing a List of Routes...................................................... 14Editing a Saved Route......................................................... 14Browsing for and Navigating a Saved Route....................... 15Browsing for and Navigating Parallel to a Saved Route...... 15Deleting a Saved Route....................................................... 15Deleting All Saved Routes................................................... 15Auto Guidance.......................................................................... 15Setting and Following an Auto Guidance Path.................... 15Creating an Auto Guidance Path......................................... 15Table of Contents i
Filtering a List of Routes and Auto Guidance Paths............ 15Reviewing an Auto Guidance Path...................................... 15Adjusting an Auto Guidance Path........................................ 15Canceling an Auto Guidance Calculation in Progress......... 15Setting a Timed Arrival.........................................................16Adjusting the Distance from Shore...................................... 16Auto Guidance Path Configurations.................................... 16Tracks....................................................................................... 16Showing Tracks................................................................... 16Setting the Color of the Active Track................................... 16Saving the Active Track....................................................... 16Viewing a List of Saved Tracks............................................ 16Editing a Saved Track.......................................................... 17Saving a Track as a Route...................................................17Browsing for and Navigating a Recorded Track.................. 17Deleting a Saved Track........................................................17Deleting All Saved Tracks.................................................... 17Retracing the Active Track................................................... 17Clearing the Active Track..................................................... 17Managing the Track Log Memory During Recording........... 17Configuring the Recording Interval of the Track Log........... 17Boundaries................................................................................17Creating a Boundary............................................................ 17Boundary Display Settings.............................................. 17Converting a Route to a Boundary...................................... 17Converting a Track to a Boundary....................................... 17Editing a Boundary...............................................................17Setting a Boundary Alarm.................................................... 18Deleting a Boundary............................................................ 18Sonar Fishfinder........................................................... 18Stopping the Transmission of Sonar Signals............................ 18Changing the Sonar View......................................................... 18Traditional Sonar View..............................................................18Split-Frequency Sonar View................................................ 18Split-Zoom Sonar View........................................................ 18Garmin ClearVü Sonar View.....................................................18SideVü Sonar View................................................................... 18SideVü Scanning Technology.............................................. 19Panoptix Sonar Views...............................................................19LiveVü Down Sonar View.................................................... 19LiveVü Forward Sonar View................................................ 19RealVü 3D Forward Sonar View.......................................... 19RealVü 3D Down Sonar View.............................................. 20RealVü 3D Historical Sonar View........................................ 20FrontVü Sonar View............................................................. 20Selecting the Transducer Type................................................. 20Calibrating the Compass......................................................20Creating a Waypoint on the Sonar Screen............................... 20Pausing the Sonar Display....................................................... 20Viewing Sonar History.............................................................. 20Sonar Sharing........................................................................... 20Selecting a Sonar Source.................................................... 20Renaming a Sonar Source...................................................21Adjusting the Level of Detail..................................................... 21Adjusting the Color Intensity..................................................... 21Sonar Recordings..................................................................... 21Recording the Sonar Display............................................... 21Stopping the Sonar Recording............................................. 21Deleting a Sonar Recording................................................. 21Playing Sonar Recordings................................................... 21Traditional, Garmin ClearVü, and SideVü Sonar Setup........... 21Setting the Zoom Level on the Sonar Screen...................... 21Setting the Scroll Speed...................................................... 22Adjusting the Range of the Depth or Width Scale............... 22Sonar Appearance Settings................................................. 22Sonar Alarms....................................................................... 22Advanced Sonar Settings.................................................... 22Transducer Installation Settings...........................................22Sonar Frequencies...............................................................23Selecting Frequencies.....................................................23Creating a Frequency Preset.......................................... 23Turning On the A-Scope...................................................... 23Panoptix Sonar Setup............................................................... 23Adjusting the RealVü Viewing Angle and Zoom Level......... 23Adjusting the RealVü Sweep Speed.................................... 23LiveVü Forward and FrontVü Sonar Menu.......................... 23Setting the LiveVü and FrontVü Transducer Transmit Angle............................................................................... 24Setting the FrontVü Depth Alarm.................................... 24LiveVü and FrontVü Appearance Settings........................... 24RealVü Appearance Settings............................................... 24Panoptix Transducer Installation Settings........................... 24Setting the Bow Offset.................................................... 25Autopilot........................................................................ 25Autopilot Screen....................................................................... 25Adjusting the Step Steering Increment................................ 25Setting the Power Saver...................................................... 25Engaging the Autopilot............................................................. 25Steering Patterns...................................................................... 25Following the U-Turn Pattern............................................... 25Setting Up and Following the Circles Pattern...................... 25Setting Up and Following the Zigzag Pattern...................... 26Following the Williamson Turn Pattern................................ 26Sailing Features............................................................ 26Setting the Vessel Type............................................................ 26Sail Racing................................................................................26Starting Line Guidance........................................................ 26Setting the Starting Line.................................................. 26Using the Starting Line Guidance................................... 26Using the Race Timer.......................................................... 26Setting the Distance between the Bow and the GPS Antenna................................................................................26Laylines Settings.......................................................................26Setting the Keel Offset.............................................................. 26Sailboat Autopilot Operation..................................................... 27Wind Hold............................................................................ 27Setting the Wind Hold Type............................................ 27Engaging Wind Hold....................................................... 27Engaging Wind Hold from Heading Hold........................ 27Adjusting the Wind Hold Angle with the Autopilot........... 27Tack and Gybe.....................................................................27Tacking and Gybing from Heading Hold......................... 27Tacking and Gybing from Wind Hold.............................. 27Setting a Tack and Gybe Delay...................................... 27Enabling the Gybe Inhibitor............................................. 27Gauges and Graphs..................................................... 27Viewing the Compass............................................................... 27Viewing Trip Gauges................................................................ 28Resetting Trip Gauges......................................................... 28Viewing Engine and Fuel Gauges............................................ 28Selecting the Number of Engines Shown in Gauges........... 28Customizing the Engines Shown in Gauges........................ 28Enabling Status Alarms for Engine Gauges........................ 28Enabling Some Engine Gauge Status Alarms..................... 28Setting the Fuel Alarm.............................................................. 28Setting the Fuel Capacity of the Vessel............................... 28Synchronizing the Fuel Data with the Actual Vessel Fuel... 28Viewing the Wind Gauges........................................................ 28Configuring the Sailing Wind Gauge.................................... 28Configuring the Speed Source............................................. 28Configuring the Heading Source of the Wind Gauge........... 28ii Table of Contents
Customizing the Close-Hauled Wind Gauge....................... 28Tide, Current, and Celestial Information.................... 29Tide Station Information............................................................29Current Station Information.......................................................29Celestial Information................................................................. 29Viewing Tide Station, Current Station, or Celestial Information for a Different Date................................................................... 29Viewing Information for a Different Tide or Current Station...... 29Digital Selective Calling............................................... 29Chartplotter and NMEA 0183 VHF Radio Functionality............ 29Turning On DSC....................................................................... 29DSC List....................................................................................29Viewing the DSC List........................................................... 29Adding a DSC Contact......................................................... 29Incoming Distress Calls............................................................ 29Navigating to a Vessel in Distress....................................... 29Position Tracking...................................................................... 29Viewing a Position Report.................................................... 30Navigating to a Tracked Vessel........................................... 30Creating a Waypoint at the Position of a Tracked Vessel.... 30Editing Information in a Position Report.............................. 30Deleting a Position-Report Call............................................ 30Viewing Vessel Trails on the Chart...................................... 30Individual Routine Calls............................................................ 30Selecting a DSC Channel.................................................... 30Making an Individual Routine Call....................................... 30Making an Individual Routine Call to an AIS Target............ 30Media Player................................................................. 30Opening the Media Player........................................................ 30Icons.................................................................................... 30Selecting the Media Source...................................................... 30Playing Music............................................................................31Browsing for Music...............................................................31Enabling Alphabetical Search......................................... 31Setting a Song to Repeat..................................................... 31Setting All Songs to Repeat................................................. 31Setting Songs to Shuffle...................................................... 31Adjusting the Volume................................................................ 31Enabling and Disabling Zones............................................. 31Muting the Media Volume.................................................... 31VHF Radio................................................................................ 31Scanning VHF Channels......................................................31Adjusting the VHF Squelch.................................................. 31Radio........................................................................................ 31Setting the Tuner Region..................................................... 31Changing the Radio Station................................................. 31Changing the Tuning Mode................................................. 31Presets................................................................................. 31Saving a Station as a Preset........................................... 31Selecting a Preset........................................................... 31Removing a Preset..........................................................31DAB Playback........................................................................... 31Setting the DAB Tuner Region............................................ 31Scanning for DAB Stations.................................................. 31Changing DAB Stations....................................................... 32Selecting a DAB Station from a List................................ 32Selecting a DAB Station from a Category....................... 32DAB Presets........................................................................ 32Saving a DAB Station as a Preset.................................. 32Selecting a DAB Preset from a List................................. 32Removing DAB Presets.................................................. 32SiriusXM Satellite Radio........................................................... 32Locating a SiriusXM Radio ID.............................................. 32Activating a SiriusXM Subscription...................................... 32Customizing the Channel Guide.......................................... 32Saving a SiriusXM Channel to the Presets List................... 32Unlocking SiriusXM Parental Controls................................. 32Setting Parental Controls on SiriusXM Radio Channels......................................................................... 32Changing a Parental Passcode on a SiriusXM Radio..... 32Restoring Default Parental Control Settings Values....... 33Clearing All Locked Channels on a SiriusXM Radio....... 33Setting the Device Name.......................................................... 33Updating the Media Player Software........................................ 33Device Configuration................................................... 33Turning On the Chartplotter Automatically............................... 33System Settings........................................................................ 33Display Settings................................................................... 33GPS Settings....................................................................... 33Viewing the Event Log......................................................... 33Viewing System Software Information................................. 33My Vessel Settings................................................................... 33Setting the Keel Offset......................................................... 34Setting the Water Temperature Offset................................. 34Calibrating a Water Speed Device....................................... 34Setting the Fuel Capacity of the Vessel............................... 34Synchronizing the Fuel Data with the Actual Vessel Fuel... 34Customizing Engine Gauge and Fuel Gauge Limits............ 34Communications Settings......................................................... 35NMEA 0183..........................................................................35NMEA 0183 Settings....................................................... 35NMEA 2000 Settings............................................................35Naming Devices and Sensors on the Network............... 35Wi‑Fi Network...................................................................... 35Setting Up the Wi‑Fi Wireless Network........................... 35Connecting a Wireless Device to the Chartplotter.......... 35Changing the Wireless Channel..................................... 35Setting Alarms.......................................................................... 35Navigation Alarms................................................................ 35System Alarms..................................................................... 35Setting the Fuel Alarm......................................................... 35Units Settings............................................................................36Navigation Settings................................................................... 36Other Vessel Settings............................................................... 36Restoring the Original Chartplotter Factory Settings................ 36Sharing and Managing User Data............................... 36Connecting to a Garmin Device to Share User Data................ 36User Data Sharing Cable Wiring Diagram........................... 36Selecting a File Type for Third-Party Waypoints and Routes... 37Copying User Data from a Memory Card................................. 37Copying User Data to a Memory Card......................................37Copying Built-In Maps to a Memory Card................................. 37Copying Waypoints, Routes, and Tracks from HomePort to a Chartplotter............................................................................... 37Backing Up Data to a Computer............................................... 37Restoring Backup Data to a Chartplotter.................................. 37Saving System Information to a Memory Card......................... 37Clearing Saved Data.................................................................37Appendix....................................................................... 37Cleaning the Screen................................................................. 37Screenshots.............................................................................. 38Capturing Screenshots........................................................ 38Copying Screenshots to a Computer................................... 38Troubleshooting........................................................................ 38My device will not acquire GPS signals............................... 38My device will not turn on or keeps turning off..................... 38Changing the Fuse in the Power Cable.......................... 38My sonar does not work....................................................... 38My device is not creating waypoints in the correct location.................................................................................38Table of Contents iii
My device does not display the correct time........................ 38NMEA 2000 PGN Information...................................................38NMEA 0183 Information........................................................... 39Registering Your Device........................................................... 39Software Update....................................................................... 39Loading the New Software on a Memory Card.................... 40Updating the Device Software............................................. 40Garmin Support Center.............................................................40Index.............................................................................. 41iv Table of Contents
Introduction WARNINGSee the Important Safety and Product Information guide in the product box for product warnings and other important information.ECHOMAP Plus 40 Device ViewÀDevice keysÁmicroSD® memory card slotÂPower and transducer connectorsÃBeeperNOTICEEach time you place the device in the bracket, you should make sure the device is firmly secured in the cradle, the cables are fully pushed into the device and cradle, and the locking bracket is snapped firmly closed. There is an audible click when the device or locking bracket is installed correctly. If the cables are not fully seated and the device is not firmly secured, it can lose power or stop working. The device can also fall out of the cradle and become damaged if it is not firmly secured.Device KeysTurns on and off the device when held.Opens a shortcut menu to backlight, color mode, and sonar transmission when quickly pressed and released.Scrolls through the brightness levels when pressed repeatedly.Zooms out of a chart or view.Zooms in to a chart or view.Scrolls, highlights options, and moves the cursor.SELECT Acknowledges messages and selects options.BACK Returns to the previous screen.MARK Saves the present location as a waypoint.HOME Returns to the Home screen.Takes a screenshot when held.MENU Opens a menu of options for the page, when applicable.Closes a menu, when applicable.Takes a screenshot when held.ECHOMAP Plus 60 Front ViewÀPower keyÁAutomatic backlight sensorÂKeysÃmicroSD memory card slotNOTICEEach time you place the device in the cradle, you should make sure the device is firmly secured in the cradle, the cables are fully pushed into the device and cradle, and the locking bracket is snapped firmly closed. There is an audible click when the locking bracket is installed correctly. If the cables are not fully seated and the device is not firmly secured, it can lose power or stop working. The device can also fall out of the cradle and become damaged if it is not firmly secured.Device KeysTurns on and off the device when held.Opens a shortcut menu to backlight, color mode, and sonar transmission when quickly pressed and released.Scrolls through the brightness levels when pressed repeatedly.Zooms out of a chart or view.Zooms in to a chart or view.Scrolls, highlights options, and moves the cursor.SELECT Acknowledges messages and selects options.BACK Returns to the previous screen.MARK Saves the present location as a waypoint.HOME Returns to the Home screen.Takes a screenshot when held.MENU Opens a menu of options for the page, when applicable.Closes a menu, when applicable.Takes a screenshot when held.ECHOMAP Plus 70/90 Front ViewÀPower keyÁAutomatic backlight sensorÂTouchscreenÃShortcut keysÄmicroSD memory card slotIntroduction 1
Device KeysTurns on and off the device when held.Opens a shortcut menu to backlight, color mode, and sonar transmission when quickly pressed and released.Scrolls through the brightness levels when pressed repeatedly.1 2 3 4 Assigns a shortcut key to the active screen when held.Opens the assigned screen when pressed.Assigning a Shortcut KeyYou can quickly open commonly used screens by assigning a shortcut key. You can create a shortcut to screens such as sonar screens and charts.1Open a screen.2Hold a shortcut key, and select OK.TIP: The shortcut is also saved to the Frequently Used category with the shortcut key number.Getting the Owner's ManualGo to garmin.com/manuals/echomapplus60-70-90.Acquiring GPS Satellite SignalsThe device may need a clear view of the sky to acquire satellite signals. The time and date are set automatically based on the GPS position.1Turn on the device.2Wait while the device locates satellites.It may take 30 to 60 seconds to acquire satellite signals.When the device acquires satellite signals, appears at the top of the Home screen.If the device loses satellite signals, disappears and a flashing question mark appears over on the chart.For more information about GPS, go to garmin.com/aboutGPS. For help acquiring satellite signals, see (My device will not acquire GPS signals, page 38).Selecting the GPS SourceYou can select your preferred source for GPS data, if you have more than one GPS source.1Select Settings > System > GPS.2Select the source for GPS data.Inserting Memory CardsYou can use optional memory cards with the chartplotter. Map cards allow you to view high-resolution satellite imagery and aerial reference photos of ports, harbors, marinas, and other points of interest. You can use blank memory cards to record Garmin Quickdraw™ Contours mapping, record sonar (with a compatible transducer), transfer data such as waypoints and routes to another compatible chartplotter or a computer, and use the ActiveCaptain™ app.This device supports up to a 32 GB memory card, formatted to FAT32.1Open the access flap or door À on the front of the chartplotter.2Insert the memory card Á.3Press the card in until it clicks.4Close the door.Customizing the ChartplotterCustomizing the Home ScreenYou can add items to and rearrange items on the Home screen.1From the Home screen, select Customize Home.2Select an option:• To rearrange an item, select Rearrange, select the item to move, and select the new location.• To add an item to the Home screen, select Add, and select the new item.• To remove an item you have added to the Home screen, select Remove, and select the item.Customizing PagesCustomizing a Combination Page1Open a combination page.2Select MENU > Configure.3Select an option:• To change the name, select Name, and enter a new name.• To change the arrangement of the information on the screen, select Change Layout, and select a new layout.• To change the information shown on the screen, select Change Function, and select new information.• To resize the information areas shown on the screen, select Resize Combination.• To customize the data shown on the screen, select Overlay Numbers (Overlay Numbers Settings, page 9).Creating a New Combination Page with the ECHOMAP Plus 70/90You can create a custom combination page to suit your needs.1Select Combos > Customize > Add.2Select a layout.3Select an area.4Select a function for the area.5Repeat these steps for each area of the page.6Drag the arrows to resize the areas.7Hold an area to rearrange it.8Hold a data field to select new data.9Select Done when you have finished customizing the page.10Enter a name for the page, and select Done.Creating a New Combination Page with the ECHOMAP Plus 60You can create a custom combination page to suit your needs.1Select Combos > Customize > Add.2Select a layout.2 Customizing the Chartplotter
3Select an area.4Select a function for the area.5Repeat these steps for each area of the page.6Select Data, and customize the data shown.7Select Next when you are done customizing the page.8Enter a name for the page, and select Done.9Use the arrow keys to resize the windows.10Select to BACK to exit.Creating a New Combination Page with the ECHOMAP Plus 40You can create a custom combination page to suit your needs.1Select Combos > Customize > Add.2Select the first function.3Select the second function.4Select Split to choose the direction of the split screen (optional).5Select Next.6Enter a name for the page.TIP: Select SELECT to select the letter.7Use the arrow keys to resize the windows.8Use the arrow keys to select a location on the home screen.9Select BACK to exit.Setting the Vessel TypeYou can select your boat type to configure the chartplotter settings and to use features customized for your boat type.1Select Settings > My Vessel > Vessel Type.2Select an option.Adjusting the Backlight1Select Settings > System > Display > Backlight.2Adjust the backlight.TIP: From any screen, press repeatedly to scroll through the brightness levels. This can be helpful when the brightness is so low you cannot see the screen.Adjusting the Color Mode1Select Settings > System > Display > Color Mode.TIP: Select > Display > Color Mode from any screen to access the color settings.2Select an option.ActiveCaptain App CAUTIONThis feature allows users to submit information. Garmin® makes no representations about the accuracy, completeness or timeliness of information submitted by users. Any use or reliance on the information submitted by users is at your own risk.NOTE: The ActiveCaptain feature is only available on models that have Wi‑Fi® technology.If you connect to a Wi‑Fi adpater The ActiveCaptain feature is only available on models that have Wi‑Fi technology.The ActiveCaptain app provides a connection to your ECHOMAP Plus device, charts, maps, and the community for a connected boating experience.On your mobile device with the ActiveCaptain app, you can download, purchase, and update maps and charts. You can use the app to easily and quickly transfer user data, such as waypoints and routes, connect to the Garmin Quickdraw Contours Community, and update device software. You can also plan your trip, and view and control the ECHOMAP Plus device from the app.You can connect to the ActiveCaptain community for up-to-date feedback on marinas and other points of interest. The app can push smart notifications, such as calls and texts, to your chartplotter display when paired.ActiveCaptain RolesYour level of interaction with the ECHOMAP Plus device using the ActiveCaptain app depends on your role.Feature Owner GuestRegister device, built-in maps, and supplemental map cards to accountYesUpdate software Yes YesAutomatically transfer Garmin Quickdraw contours you have downloaded or createdYesPush smart notifications Yes YesBegin navigating to a specific waypoint or navigating a specific routeYes YesManually synchronize waypoints and routes with the ECHOMAP Plus deviceYes YesGetting Started with the ActiveCaptain AppNOTE: The ActiveCaptain feature is only available on models that have Wi‑Fi technology.You can connect a mobile device to the ECHOMAP Plus device using the ActiveCaptain app. The app provides a quick and easy way for you to interact with your chartplotter and complete such tasks as sharing data, registering, updating the device software, and receiving mobile device notifications.1From the ECHOMAP Plus device, select ActiveCaptain.2From the ActiveCaptain page, select Wi-Fi Network > Wi-Fi > On.3Enter a name and password for this network.4Insert a memory card in the ECHOMAP Plus device's card slot (Inserting Memory Cards, page 2).5Select Create ActiveCaptain Memory Card.NOTICEYou might be prompted to format the memory card. Formatting the card deletes all information saved on the card. This includes any saved user data, such as waypoints. Formatting the card is recommended, but not required. Before formatting the card, you should save the data from the memory card onto the device internal memory (Copying User Data from a Memory Card, page 37). After formatting the card for the ActiveCaptain app, you can transfer the user data back to the card (Copying User Data to a Memory Card, page 37).Be sure the card is inserted each time you want to use the ActiveCaptain feature.6From the application store on your mobile device, install and open the ActiveCaptain app.7Bring the mobile device within 32 m (105 ft.) of the ECHOMAP Plus device.ActiveCaptain App 3
8From your mobile device settings, open the Wi‑Fi connections page and connect to the Garmin device, using the name and password you entered in the Garmin device.Receiving Smart NotificationsWith the ActiveCaptain app, the ECHOMAP Plus device can show notifications received from your mobile device.1From the ECHOMAP Plus device, select ActiveCaptain > Smart Notifications > Enable Notifications.2Turn on Bluetooth® technology in the mobile device settings.3Bring the devices within 10 m (33 ft.) of each other.4From the ActiveCaptain app on the mobile device, select Smart Notifications > Pair with Chartplotter.5Follow the on-screen instructions to pair the app to the ECHOMAP Plus device using Bluetooth technology.6When prompted, enter the key on your mobile device.7If necessary, adjust the notifications in your mobile device settings.Updating Software with the ActiveCaptain AppIf your device has Wi‑Fi technology, you can use the ActiveCaptain app to download and install the latest software updates for your device.NOTICESoftware updates may require the app to download large files. Regular data limits or charges from your Internet service provider apply. Contact your Internet service provider for more information about data limits or charges.The installation process can take several minutes.1Connect the mobile device to the ECHOMAP Plus device (Getting Started with the ActiveCaptain App, page 3).2When a software update is available and you have internet access on your mobile device, select Software Updates > Download.The ActiveCaptain app downloads the update to the mobile device. When you reconnect the app to the ECHOMAP Plus device, the update is transferred to the device. After the transfer is complete, you are prompted to install the update.3When you are prompted by the ECHOMAP Plus device, select an option to install the update.• To update the software immediately, select OK.• To delay the update, select Cancel. When you are ready to install the update, select ActiveCaptain > Software Updates > Install Now.Updating Charts with ActiveCaptainIf your device has Wi‑Fi technology, you can use the ActiveCaptain app to download and install the latest software updates for your device.NOTICEChart updates may require the app to download large files. Regular data limits or charges from your Internet service provider apply. Contact your Internet service provider for more information about data limits or charges.1Connect the mobile device to the ECHOMAP Plus device (Getting Started with the ActiveCaptain App, page 3).2When a chart update is available, and you have internet access on your mobile device, select OneChart > My Charts.3Select the map to update.4Select the area to download.5Select DownloadThe ActiveCaptain app downloads the update to the mobile device. When you reconnect the app to the ECHOMAP Plus device, the update is transferred to the device. After the transfer is complete, the updated charts are available for use.Charts and 3D Chart ViewsThe charts and 3D chart views that are available depend on the map data, accessories used.NOTE: Not available on ECHOMAP Plus 40 devices.You can access the charts and 3D chart views by selecting Charts.Navigation Chart: Shows navigation data available on your pre-loaded maps and from supplemental maps, if available. The data includes buoys, lights, cables, depth soundings, marinas, and tide stations in an overhead view.Perspective 3D: Provides a view from above and behind the boat (according to your course) and provides a visual navigation aid. This view is helpful when navigating tricky shoals, reefs, bridges, or channels, and is beneficial when trying to identify entry and exit routes in unfamiliar harbors or anchorages.Mariner’s Eye 3D: Shows a detailed, three-dimensional view from above and behind the boat (according to your course) and provides a visual navigation aid. This view is helpful when navigating tricky shoals, reefs, bridges, or channels, and when trying to identify entry and exit routes in unfamiliar harbors or anchorages.NOTE: Mariner's Eye 3D and Fish Eye 3D chart views are available with premium charts, in some areas.Fish Eye 3D: Provides an underwater view that visually represents the sea floor according to the chart information. When a sonar transducer is connected, suspended targets (such as fish) are indicated by red, green, and yellow spheres. Red indicates the largest targets and green indicates the smallest.Fishing Chart: Provides a detailed view of the bottom contours and depth soundings on the chart. This chart removes navigational data from the chart, provides detailed bathymetric data, and enhances bottom contours for depth recognition. This chart is best for offshore deep-sea fishing.NOTE: The offshore Fishing chart is available with premium charts, in some areas.Navigation Chart and Fishing ChartNOTE: The offshore Fishing chart is available with premium charts, in some areas.The Navigation Chart is optimized for navigation. You can plan a course, view map information, and use the chart as a navigational aid. To open the Navigation Chart, select Charts > Navigation Chart.The Fishing Chart provides a detailed view with more bottom detail and fishing content. This chart is optimized for use when fishing. To open the Fishing Chart, select Charts > Fishing Chart.4 Charts and 3D Chart Views
Zooming In and Out of the ChartThe zoom level is indicated by the scale number at the bottom of the chart. The bar under the scale number represents that distance on the chart.• To zoom out, select or pinch two fingers together on the touchscreen.• To zoom in, select or spread two fingers apart on the touchscreen.Panning the Chart with the KeysYou can move the chart to view an area other than your present location.1From the chart, use the arrow keys.2Select BACK to stop panning and return the screen to your present location.NOTE: To pan from a combination screen, select SELECT.Selecting an Item on the Map Using the Device Keys1From a chart or 3D chart view, select , , , or to move the cursor.2Select SELECT.Chart SymbolsThis table contains some of the common symbols you might see on the detailed charts.Icon DescriptionBuoyInformationMarine servicesTide stationCurrent stationOverhead photo availablePerspective photo availableOther features common to most charts include depth contour lines, intertidal zones, spot soundings (as depicted on the original paper chart), navigational aids and symbols, obstructions, and cable areas.Measuring a Distance on the Chart1From a chart, select a location.2Select Measure Distance.A push pin appears on the screen at your present location. The distance and angle from the pin is listed in the corner.TIP: To reset the pin and measure from the current location of the cursor, select SELECT.Creating a Waypoint on the Chart1From a chart or a 3D chart view, select a location or object, and select SELECT.A list of options appears along the right side of the chart. The options that appear vary based on the location or object you selected.2Select Create Waypoint.Navigating to a Point on the Chart CAUTIONThe Auto Guidance feature is based on electronic chart information. That data does not ensure obstacle and bottom clearance. Carefully compare the course to all visual sightings, and avoid any land, shallow water, or other obstacles that may be in your path.When using Go To, a direct course and a corrected course may pass over land or shallow water. Use visual sightings, and steer to avoid land, shallow water, and other dangerous objects.NOTE: The offshore Fishing chart is available with premium charts, in some areas.NOTE: Auto Guidance is available with premium charts, in some areas.1From the Navigation chart or Fishing chart, select a location.2If necessary, select SELECT.3Select Navigate To.4Select an option:• To navigate directly to the location, select Go To.• To create a route to the location, including turns, select Route To.• To use Auto Guidance, select Auto Guidance.5Review the course indicated by the magenta line.NOTE: When using Auto Guidance, a gray segment within any part of the magenta line indicates that Auto Guidance cannot calculate part of the Auto Guidance line. This is due to the settings for minimum safe water depth and minimum safe obstacle height.6Follow the magenta line, steering to avoid land, shallow water, and other obstacles.Viewing Location and Object Information on a ChartYou can view information about a location or an object on the Navigation chart or the Fishing chart.NOTE: The offshore Fishing chart is available with premium charts, in some areas.1From the Navigation chart or Fishing chart, select a location or object, and select SELECT.A list of options appears along the right side of the chart. The options that appear vary based on the location or object you selected.2Select an option:• To navigate to the selected location, select Navigate To.• To mark a waypoint at the cursor location, select Create Waypoint.• To view the distance and bearing of the object from your current location, select Measure Distance.The distance and bearing appear on the screen. Select SELECT to measure from a location other than your current location.• To view tide, current, celestial, chart notes, or local services information near the cursor, select Information.Viewing Details about NavaidsFrom the Navigation chart, Fishing chart, Perspective 3D chart view, or Mariner’s Eye 3D chart view, you can view details about various types of navigation aids, including beacons, lights, and obstructions.NOTE: The offshore Fishing chart is available with premium charts, in some areas.NOTE: Mariner's Eye 3D and Fish Eye 3D chart views are available with premium charts, in some areas.1From a chart or 3D chart view, select a navaid.2Select the name of the navaid.Heading Line and Angle MarkersThe heading line is an extension drawn on the map from the bow of the boat in the direction of travel. Angle markers indicate relative position from the heading or course over ground, which are helpful for casting or finding reference points.Charts and 3D Chart Views 5
Setting the Heading and Course Over Ground LinesYou can show the heading line and the course over ground (COG) line on the chart.COG is your direction of movement. Heading is the direction the bow of the boat is pointed, when a heading sensor is connected.1From a chart view, select MENU > Chart Setup > Chart Appearance > Heading Line.2If necessary, select Source, and select an option:• To automatically use the source available, select Auto.• To use the GPS antenna heading for COG, select GPS Heading (COG).• To use data from a connected heading sensor, select Heading.• To use data from both a connected heading sensor and the GPS antenna, select COG and Heading.This displays both the heading line and the COG line on the chart.3Select Display, and select an option:• Select Distance > Distance, and enter the length of the line shown on the chart.• Select Time > Time, and enter the time used to calculate the distance your boat will travel in the specified time at your present speed.Turning on Angle MarkersYou can add angle markers to the map along the heading line. Angle markers can be helpful for casting when fishing.1Set the heading line (Setting the Heading and Course Over Ground Lines, page 6).2Select Angle Markers.Premium Charts CAUTIONThe Auto Guidance feature is based on electronic chart information. That data does not ensure obstacle and bottom clearance. Carefully compare the course to all visual sightings, and avoid any land, shallow water, or other obstacles that may be in your path.NOTE: Not all models support all charts.Optional premium charts, such as BlueChart® g2 Vision®, allow you to get the most out of your chartplotter. In addition to detailed marine charting, premium charts may contain these features, which are available in some areas.Mariner’s Eye 3D: Provides a view from above and behind the boat for a three-dimensional navigation aid.Fish Eye 3D: Provides an underwater, three-dimensional view that visually represents the sea floor according to the information on the chart.Fishing Charts: Shows the chart with enhanced bottom contours and without navigational data. This chart works well for offshore deep-sea fishing.High Resolution Satellite Imagery: Provides high-resolution satellite images for a realistic view of the land and water on the Navigation chart (Showing Satellite Imagery on the Navigation Chart, page 6).Aerial Photos: Shows marinas and other navigationally significant aerial photos to help you visualize your surroundings (Viewing Aerial Photos of Landmarks, page 7).Detailed Roads and POI data: Shows detailed road and point of interest (POI) data, which includes highly detailed coastal roads and POIs such as restaurants, lodging, and local attractions.Auto Guidance: Uses specified information about your vessel and chart data to determine the best path to your destination.Viewing Tide Station Information on the chart indicates a tide station. You can view a detailed graph for a tide station to help predict the tide level at different times or on different days.NOTE: This feature is available with premium charts, in some areas.1From the Navigation chart or Fishing chart, select a tide station.Tide direction and tide level information appear near .2Select the station name.Animated Tide and Current IndicatorsNOTE: This feature is available with premium charts, in some areas.You can view indicators for animated tide station and current direction on the Navigation chart or the Fishing chart. You must also enable animated icons in the chart settings (Showing Tides and Current Indicators, page 6).An indicator for a tide station appears on the chart as a vertical bar graph with an arrow. A red arrow pointing downward indicates a falling tide, and a blue arrow pointing upward indicates a rising tide. When you move the cursor over the tide station indicator, the height of the tide at the station appears above the station indicator.Current direction indicators appear as arrows on the chart. The direction of each arrow indicates the direction of the current at a specific location on the chart. The color of the current arrow indicates the range of speed for the current at that location. When you move the cursor over the current direction indicator, the specific current speed at the location appears above the direction indicator.Color Current Speed RangeYellow 0 to 1 knotOrange 1 to 2 knotsRed 2 or more knotsShowing Tides and Current IndicatorsNOTE: This feature is available with premium charts, in some areas.You can show static or animated tide and current station indicators on the Navigation chart or Fishing chart.1From the Navigation or Fishing chart, select MENU > Chart Setup > Tides & Currents.2Select an option:• To show current station indicators and tide station indicators on the chart, select On.• To show animated tide station indicators and animated current direction indicators on the chart, select Animated.Showing Satellite Imagery on the Navigation ChartNOTE: This feature is available with premium charts, in some areas.You can overlay high-resolution satellite images on the land or on both land and sea portions of the Navigation chart.NOTE: When enabled, high-resolution satellite images are present only at lower zoom levels. If you cannot see high-resolution images in your optional chart region, you can select to zoom in. You also can set the detail level higher by changing the map zoom detail.1From the Navigation chart, select MENU > Chart Setup > Satellite Photos.2Select an option:• Select Land Only to show standard chart information on the water, with photos overlaying the land.6 Charts and 3D Chart Views
• Select Photo Map Blend to show photos on both the water and the land at a specified opacity. Use the slider bar to adjust the photo opacity. The higher you set the percentage, the more the satellite photos cover both land and water.Viewing Aerial Photos of LandmarksBefore you can view aerial photos on the Navigation chart, you must turn on the Satellite Photos setting in the chart setup.NOTE: This feature is available with premium charts, in some areas.You can use aerial photographs of landmarks, marinas, and harbors to help orient yourself to your surroundings or to acquaint yourself with a marina or a harbor prior to arrival.1From the Navigation chart, select a camera icon:• To view an overhead photo, select .• To view a perspective photo, select . The photo was taken from the location of the camera, pointed in the direction of the cone.2Select Aerial Photo.Automatic Identification SystemThe Automatic Identification System (AIS) enables you to identify and track other vessels, and alerts you to area traffic. When connected to an external AIS device, the chartplotter can show some AIS information about other vessels that are within range, that are equipped with a transponder, and that are actively transmitting AIS information.The information reported for each vessel includes the Maritime Mobile Service Identity (MMSI), location, GPS speed, GPS heading, time that has elapsed since the last position of the vessel was reported, nearest approach, and time to the nearest approach.Some chartplotter models also support Blue Force Tracking. Vessels being tracked with Blue Force Tracking are indicated on the chartplotter with a blue-green color.AIS Targeting SymbolsSymbol DescriptionAIS vessel. The vessel is reporting AIS information. The direction in which the triangle is pointing indicates the direction in which the AIS vessel is moving.Target is selected.Target is activated. The target appears larger on the chart. A green line attached to the target indicates the heading of the target. The MMSI, speed, and direction of the vessel appear beneath the target, if the details setting has been set to Show. If the AIS transmission from the vessel is lost, a message banner appears.Target is lost. A green X indicates that the AIS transmission from the vessel is lost, and the chartplotter displays a message banner asking whether the vessel should continue to be tracked. If you discontinue vessel tracking, the lost target symbol disappears from the chart or the 3D chart view.Dangerous target in range. The target flashes while an alarm sounds and a message banner appears. After the alarm has been acknowledged, a solid red triangle with a red line attached to it indicates the location and the heading of the target. If the safe-zone collision alarm has been set to Off, the target flashes, but the audible alarm does not sound and the alarm banner does not appear. If the AIS transmission from the vessel is lost, a message banner appears.Symbol DescriptionDangerous target is lost. A red X indicates that the AIS transmission from the vessel is lost, and the chartplotter displays a message banner asking whether the vessel should continue to be tracked. If you discontinue vessel tracking, the lost dangerous target symbol disappears from the chart or the 3D chart view.The location of this symbol indicates the closest point of approach to a dangerous target, and the numbers near the symbol indicate the time to the closest point of approach to that target.NOTE: Vessels being tracked with the Blue Force Tracking feature are indicated with a blue-green color regardless of their status.Heading and Projected Course of Activated AIS TargetsWhen heading and course over ground information are provided by an activated AIS target, the heading of the target appears on a chart as a solid line attached to the AIS target symbol. A heading line does not appear on a 3D chart view.The projected course of an activated AIS target appears as a dashed line on a chart or a 3D chart view. The length of the projected course line is based on the value of the projected heading setting. If an activated AIS target is not transmitting speed information, or if the vessel is not moving, a projected course line does not appear. Changes in the speed, course over ground, or rate of turn information transmitted by the vessel can impact the calculation of the projected course line.When course over ground, heading, and rate of turn information are provided by an activated AIS target, the projected course of the target is calculated based on the course over ground and the rate of turn information. The direction in which the target is turning, which is also based on the rate of turn information, is indicated by the direction of the barb at the end of the heading line. The length of the barb does not change.When course over ground and heading information are provided by an activated AIS target, but rate of turn information is not provided, the projected course of the target is calculated based on the course over ground information.Showing AIS Vessels on a Chart or 3D Chart ViewBefore you can use AIS, you must connect the chartplotter to an external AIS device and receive active transponder signals from other vessels.You can configure how other vessels appear on a chart or on a 3D chart view. The display range configured for one chart or one 3D chart view are applied only to that chart or to that 3D chart view. The details, projected heading, and trails settings configured for one chart or one 3D chart view are applied to all charts and to all 3D chart views.1From a chart or 3D chart view, select MENU > Other Vessels > AIS Display Setup.2Select an option:• To indicate the distance from your location in which AIS vessels appear, select Display Range, and select a distance.• To show details about AIS-activated vessels, select Details > Show.• To set the projected heading time for AIS-activated vessels, select Proj. Heading, and enter the time.• To show the tracks of AIS vessels, select Trails, and select the length of the track that appears using a trail.Charts and 3D Chart Views 7
Activating a Target for an AIS Vessel1From a chart or a 3D chart view, select an AIS vessel.2Select AIS Vessel > Activate Target.Viewing Information about a Targeted AIS VesselYou can view the AIS signal status, MMSI, GPS speed, GPS heading, and other information that is reported about a targeted AIS vessel.1From a chart or a 3D chart view, select an AIS vessel.2Select AIS Vessel.Deactivating a Target for an AIS Vessel1From a chart or a 3D chart view, select an AIS vessel.2Select AIS Vessel > Deactivate Target.Viewing a List of AIS ThreatsFrom a chart or 3D chart view, select MENU > Other Vessels > AIS List.Setting the Safe-Zone Collision AlarmBefore you can set a safe-zone collision alarm, you must have a compatible chartplotter connected to an AIS device.The safe-zone collision alarm is used only with AIS. The safe zone is used for collision avoidance, and can be customized.1Select Settings > Alarms > AIS > AIS Alarm > On.A message banner appears and an alarm sounds when an AIS-activated vessel enters the safe-zone area around your boat. The object is also labeled as dangerous on the screen. When the alarm is off, the message banner and audible alarm are disabled, but the object is still labeled as dangerous on the screen.2Select Range.3Select a distance for the safe-zone radius around your vessel.4Select Time To.5Select a time at which the alarm will sound if a target is determined to intersect the safe zone.For example, to be notified of a pending intersection 10 minutes before it will likely occur, set Time To to 10, and the alarm will sound 10 minutes before the vessel intersects the safe zone.AIS Distress SignalsSelf-contained AIS distress signal devices transmit emergency position reports when activated. The chartplotter can receive signals from Search and Rescue Transmitters (SART), Emergency Position Indicating Radio Beacons (EPIRB), and other man overboard signals. Distress signal transmissions are different than standard AIS transmissions, so they appear differently on the chartplotter. Instead of tracking a distress signal transmission for collision avoidance, you track a distress signal transmission to locate and assist a vessel or person.Navigating to a Distress Signal TransmissionWhen you receive a distress signal transmission, a distress signal alarm appears.Select Review > Go To to begin navigation to the transmission.AIS Distress Signal Device Targeting SymbolsSymbol DescriptionAIS distress signal device transmission. Select to see more information about the transmission and begin navigation.Transmission lost.Transmission test. Appears when a vessel initiates a test of their distress signal device, and does not represent a true emergency.Transmission test lost.Enabling AIS Transmission Test AlertsTo avoid a large number of test alerts and symbols in crowded areas such as marinas, you can select to receive or ignore AIS test messages. To test an AIS emergency device, you must enable the chartplotter to receive test alerts.1Select Settings > Alarms > AIS.2Select an option:• To receive or ignore Emergency Position Indicating Radio Beacon (EPRIB) test signals, select AIS-EPIRB Test.• To receive or ignore Man Overboard (MOB) test signals, select AIS-MOB Test.• To receive or ignore Search and Rescue Transponder (SART) test signals, select AIS-SART Test.Turning Off AIS ReceptionAIS signal reception is turned on by default.Select Settings > Other Vessels > AIS > Off.All AIS functionality on all charts and 3D chart views is disabled. This includes AIS vessel targeting and tracking, collision alarms that result from AIS vessel targeting and tracking, and the display of information about AIS vessels.Chart and 3D Chart View SettingsNOTE: Not all settings apply to all charts and 3D chart views. Some options require premium maps or connected accessories.These settings apply to the charts and 3D chart views, except Fish Eye 3D (Fish Eye 3D Settings, page 10).From a chart or a 3D chart view, select MENU.Waypoints & Tracks: Adjusts how waypoints and tracks are shown (Waypoints and Tracks Settings on the Charts and Chart Views, page 10).Other Vessels: Adjusts how DSC and AIS vessels are shown (Other Vessels Settings on the Charts and Chart Views, page 10).Laylines: Adjusts the laylines, when in sailing mode (Laylines Settings, page 10).Quickdraw Contours: Turns on bottom contour drawing, and allows you to create fishing map labels (Garmin Quickdraw Contours Mapping, page 10).Chart Setup: Adjusts the information shown on the chart (Navigation and Fishing Chart Setup, page 8).Navaids: Shows navigational aids on the Fishing chart.Navigation and Fishing Chart SetupNOTE: Not all settings apply to all charts and 3D chart views. Some settings require external accessories or applicable premium charts.From the Navigation chart or Fishing chart, select MENU > Chart Setup.Satellite Photos: Shows high-resolution satellite images on the land or on both land and sea portions of the Navigation chart, when certain premium maps are used (Showing Satellite Imagery on the Navigation Chart, page 6).Water Overlay: Enables relief shading, which shows the gradient of the bottom with shading, or sonar imagery, which helps identify the density of the bottom. This feature is available only with some premium maps.Tides & Currents: Shows current station indicators and tide station indicators on the chart (Showing Tides and Current Indicators, page 6) and enables the tides and current slider, which sets the time for which tides and currents are reported on the map.Roses: Shows a compass rose around your boat, indicating compass direction oriented to the heading of the boat. A true wind direction or apparent wind direction indicator appears if 8 Charts and 3D Chart Views
the chartplotter is connected to a compatible marine wind sensor. When in sailing mode, true and apparent wind are shown on the wind rose.Lake Level: Sets the present water level of the lake. This feature is available only with some premium maps.Overlay Numbers: Adjusts the data shown on the screen (Overlay Numbers Settings, page 9).Weather: Sets which weather items are shown on the chart, when the chartplotter is connected to a compatible weather receiver with an active subscription. Requires a compatible, connected antenna and an active subscription.Chart Appearance: Sets the appearance of the different charts and 3D chart views (Chart Appearance Settings, page 9).Chart Appearance SettingsYou can adjust the appearance of the different charts and 3D chart views. Each setting is specific to the chart or chart view being used.NOTE: Not all settings apply to all charts and 3D chart views and chartplotter models. Some options require premium maps or connected accessories.From a chart or 3D chart view, select MENU > Chart Setup > Chart Appearance.Orientation: Sets the perspective of the map.Detail: Adjusts the amount of detail shown on the map, at different zoom levels.Heading Line: Shows and adjusts the heading line, which is a line drawn on the map from the bow of the boat in the direction of travel, and sets the data source for the heading line.Panoptix Area: Shows and hides the area being scanned by the Panoptix™ transducer. The attitude and heading reference system (AHRS) must be calibrated use this feature (Transducer Installation Settings, page 22).World Map: Uses either a basic world map or a shaded relief map on the chart. These differences are visible only when zoomed out too far to see the detailed charts.Spot Depths: Turns on spot soundings and sets a dangerous depth. Spot depths that are equal to or more shallow than the dangerous depth are indicated by red text.Shallow Shading: Sets the shades from the shoreline to the specified depth.Depth Range Shading: Specifies an upper and lower depth to shade between.Symbols: Shows and configures the appearance of various symbols on the chart, such as the vessel icon, navaid symbols, land POIs, and light sectors.Style: Sets how the chart appears over 3D terrain.Hazard Colors: Shows shallow water and land with a color scale. Blue indicates deep water, yellow is shallow water, and red is very shallow water.Preferred Depth: Sets the appearance of a safe depth for the Mariner’s Eye 3D chart view.NOTE: This setting affects only the appearance of hazard colors for the Mariner’s Eye 3D chart view. It does not affect the safe water depth Auto Guidance setting or the sonar shallow water alarm setting.Range Rings: Shows and configures the appearance of range rings, which help you to visualize distances in some chart views.Lane Width: Specifies the width of the navigation lane, which is the magenta line in some chart views that indicates the course to your destination.Overlay Numbers SettingsFrom a chart, 3D chart view, the Radar screen, or a Combinations screen, select MENU > Overlay Numbers.From a chart, 3D chart view, or a Combinations screen, select MENU > Overlay Numbers.Edit Layout: Sets the layout of the data overlay, or data fields. You can select the data to be shown within each data field.Nav. Inset: Shows the navigation inset when the vessel is navigating to a destination.Navigation Inset Setup: Allows you to configure the navigation inset to show Route Leg Info, and to control when the inset appears before a turn or destination.Compass Tape: Shows the compass tape data bar when the vessel is navigating to a destination.Editing the Data FieldsYou can change the data shown in the overlay numbers displayed on the charts and other screens.1From a screen that supports overlay numbers, select MENU.2If necessary, select Chart Setup.3Select Overlay Numbers > Edit Layout.4Select a layout.5Select a data field.6Select the type of data shown in the field.Available data options vary based on the chartplotter.Showing a Navigation InsetYou can control whether a navigation inset appears on some chart views. The navigation inset is shown only when the boat is navigating to a destination.1From a chart or 3D chart view, select MENU.2If necessary, select Chart Setup.3Select Overlay Numbers > Nav. Inset > Auto.4Select Navigation Inset Setup.5Complete an action:• To show waypoint velocity made good (VMG) when navigating a route with more than one leg, select Route Leg Info > On.• To show next-turn data based on distance, select Next Turn > Distance.• To show next-turn data based on time, select Next Turn > Time.• To indicate how the destination data appears, select Destination, and select an option.Setting the Heading and Course Over Ground LinesYou can show the heading line and the course over ground (COG) line on the chart.COG is your direction of movement. Heading is the direction the bow of the boat is pointed, when a heading sensor is connected.1From a chart view, select MENU > Chart Setup > Chart Appearance > Heading Line.2If necessary, select Source, and select an option:• To automatically use the source available, select Auto.• To use the GPS antenna heading for COG, select GPS Heading (COG).• To use data from a connected heading sensor, select Heading.• To use data from both a connected heading sensor and the GPS antenna, select COG and Heading.This displays both the heading line and the COG line on the chart.Charts and 3D Chart Views 9
3Select Display, and select an option:• Select Distance > Distance, and enter the length of the line shown on the chart.• Select Time > Time, and enter the time used to calculate the distance your boat will travel in the specified time at your present speed.Waypoints and Tracks Settings on the Charts and Chart ViewsFrom a chart or a 3D chart view, select MENU > Waypoints & Tracks.Tracks: Shows tracks on the chart or 3D chart view.Waypoints: Shows the list of waypoints (Viewing a List of all Waypoints, page 14).Create Waypoint: Creates a new waypoint.Waypoint Display: Sets how to display waypoints on the chart.Active Tracks: Shows the active track options menu.Saved Tracks: Shows the list of saved tracks (Viewing a List of Saved Tracks, page 16).Tracks Display: Sets which tracks to display on the chart based on track color.Other Vessels Settings on the Charts and Chart ViewsNOTE: These options require connected accessories, such as an AIS receiver or VHF radio.From a chart or 3D chart view, select MENU > Other Vessels.AIS List: Shows the AIS list (Viewing a List of AIS Threats, page 8).DSC List: Shows the DSC list (DSC List, page 29).AIS Display Setup: See AIS Display Settings, page 10.DSC Trails: Shows the tracks of DSC vessels, and selects the length of the track that appears using a trail.AIS Alarm: Sets the safe-zone collision alarm (Setting the Safe-Zone Collision Alarm, page 8).AIS Display SettingsNOTE: AIS requires the use of an external AIS device and active transponder signals from other vessels.From a chart or 3D chart view, select MENU > Other Vessels > AIS Display Setup.AIS Dis. Range: Indicates the distance from your location within which AIS vessels appear.Details: Shows details about AIS-activated vessels.Proj. Heading: Sets the projected heading time for AIS-activated vessels.Trails: Shows the tracks of AIS vessels, and select the length of the track that appears using a trail.Laylines SettingsTo use the laylines features, you must connect a wind sensor to the chartplotter.When in sailing mode (Setting the Vessel Type, page 3), you can display laylines on the navigation chart. Laylines can be very helpful when racing.From the navigation chart, select MENU > Laylines.Display: Sets how the laylines and vessel appear on the chart, and sets the length of the laylines.Sailing Ang.: Allows you to select how the device calculates laylines. The Actual option calculates the laylines using the measured wind angle from the wind sensor. The Manual option calculates the laylines using manually entered windward and leeward angles.Windward Angle: Allows you to set a layline based on the windward sailing angle.Leeward Angle: Allows you to set a layline based on the leeward sailing angle.Tide Correction: Corrects the laylines based on the tide.Filter Time Constant: Filters the layline data based on the time interval entered. For a smoother layline that filters out some of the changes in the boat's heading or true wind angle, enter a higher number. For laylines that display a higher sensitivity to changes in the boat's heading or true wind angle, enter a lower number.Fish Eye 3D SettingsNOTE: This feature is available with premium charts, in some areas.From the Fish Eye 3D chart view, select MENU.View: Sets the perspective of the 3D chart view.Tracks: Shows tracks.Sonar Cone: Shows a cone that indicates the area covered by the transducer.Fish Symbols: Shows suspended targets.Supported MapsTo help you have a safe and enjoyable time on the water, Garmin devices only support official maps produced by Garmin or an approved third party producer.You can purchase maps from Garmin. If you purchase maps from a seller other than Garmin, investigate the seller before purchasing. Be extra cautious with online sellers. If you have purchased an unsupported map, return it to the seller.Garmin Quickdraw Contours Mapping WARNINGThe Garmin Quickdraw Contours mapping feature allows users to generate maps. Garmin makes no representations about the accuracy, reliability, completeness or timeliness of the maps generated by third parties. Any use or reliance on the maps generated by third parties is at your own risk.The Garmin Quickdraw Contours mapping feature allows you to instantly create maps with contours and depth labels for any body of water.When Garmin Quickdraw Contours records data, a colored circle surrounds the vessel icon. This circle represents the approximate area of the map that is scanned by each pass.A green circle indicates good depth and GPS position, and a speed under 16 km/h (10 mph). A yellow circle indicates good depth and GPS position, and a speed between 16 and 32 km/h (10 and 20 mph). A red circle indicates poor depth or GPS position, and a speed above 32 km/h (20 mph).You can view Garmin Quickdraw Contours in a combination screen or as a single view on the map.The amount of saved data depends on the size of your memory card, your sonar source, and the speed of your boat as you record data. You can record longer when you use a single-beam sonar. It is estimated that you might be able to record about 1,500 hours of data onto a 2 GB memory card.10 Garmin Quickdraw Contours Mapping
When you record data on a memory card in your chartplotter, the new data is added to your existing Garmin Quickdraw Contours map, and is saved on the memory card. When you insert a new memory card, the existing data does not transfer onto the new card.Mapping a Body of Water Using the Garmin Quickdraw Contours FeatureBefore you can use the Garmin Quickdraw Contours feature, you must have sonar depth, your GPS position, and a memory card with free space.1From a chart view, select MENU > Quickdraw Contours > Start Recording.2When recording is complete, select MENU > Quickdraw Contours > Stop Recording.3Select Manage > Name, and enter a name for the map.Adding a Label to a Garmin Quickdraw Contours MapYou can add labels to a Garmin Quickdraw Contours map to mark hazards or points of interest.1From the Navigation chart, select a location.2Select Add Quickdraw Label.3Enter text for the label, and select Done.Garmin Quickdraw CommunityThe Garmin Quickdraw Community is a free, public, online community that enables you to share your Garmin Quickdraw Contours maps with others. You can also download maps other users have created.If your device has Wi‑Fi technology, you can use the ActiveCaptain app to access the Garmin Quickdraw Community (Connecting to the Garmin Quickdraw Community with ActiveCaptain, page 11).If your device does not have Wi‑Fi technology, you can use the Garmin Connect™ website to access the Garmin Quickdraw Community (Connecting to the Garmin Quickdraw Community with Garmin Connect, page 11).Connecting to the Garmin Quickdraw Community with ActiveCaptain1From your mobile device, open the ActiveCaptain app and connect to the ECHOMAP Plus device (Getting Started with the ActiveCaptain App, page 3).2From the app, select Quickdraw Community.You can download contours from others in the community (Downloading Garmin Quickdraw Community Maps Using ActiveCaptain, page 11) and share the contours you have created (Sharing Your Garmin Quickdraw Contours Maps with the Garmin Quickdraw Community Using ActiveCaptain, page 11).Downloading Garmin Quickdraw Community Maps Using ActiveCaptainYou can download Garmin Quickdraw Contours maps that other users have created and shared with the Garmin Quickdraw Community.1From the ActiveCaptain app on your mobile device, select Quickdraw Community > Search for Contours.2Use the map and search features to locate an area to download.The red dots represent Garmin Quickdraw Contours maps that have been shared for that area.3Select Select Download Region.4Drag the box to select the area to download.5Drag the corners to change the download area.6Select Download Area.The next time you connect the ActiveCaptain app to the ECHOMAP Plus device, the downloaded contours are transferred to the device automatically.Sharing Your Garmin Quickdraw Contours Maps with the Garmin Quickdraw Community Using ActiveCaptainYou can share Garmin Quickdraw Contours maps that you have created with others in the Garmin Quickdraw Community.When you share a contour map, only the contour map is shared. Your waypoints are not shared.When you set up your ActiveCaptain app, you may have selected to share your contours with the community automatically. If not, follow these steps to enable sharing.From the ActiveCaptain app on your mobile device, select Quickdraw Community.The next time you connect the ActiveCaptain app to the ECHOMAP Plus device, your contour maps are transferred to the community automatically.Connecting to the Garmin Quickdraw Community with Garmin Connect1Go to connect.garmin.com.2Select Get Started > Quickdraw Community > Get Started.3If you do not have a Garmin Connect account, create one.4Sign in to your Garmin Connect account.5Select Marine in the upper-right to open the Garmin Quickdraw widget.TIP: Make sure you have a memory card in your computer to share Garmin Quickdraw Contours maps.Sharing Your Garmin Quickdraw Contours Maps with the Garmin Quickdraw Community Using Garmin ConnectYou can share Garmin Quickdraw Contours maps that you have created with others in the Garmin Quickdraw Community.When you share a contour map, only the contour map is shared. Your waypoints are not shared.1Remove the memory card from the chartplotter. 2Insert the memory card into your computer.3Access the Garmin Quickdraw Community (Connecting to the Garmin Quickdraw Community with Garmin Connect, page 11).4Select Share Your Contours.5Browse to your memory card, and select the Garmin folder.6Open the Quickdraw folder, and select the file named ContoursLog.svy.After the file is uploaded, delete the ContoursLog.svy file from your memory card to avoid issues with future uploads. Your data will not be lost.Downloading Garmin Quickdraw Community Maps Using Garmin ConnectYou can download Garmin Quickdraw Contours maps that other users have created and shared with the Garmin Quickdraw Community.If your device does not have Wi‑Fi technology, you can access the Garmin Quickdraw Community using the Garmin Connect website.If your device has Wi‑Fi technology, you should access the Garmin Quickdraw Community using the ActiveCaptain app (Connecting to the Garmin Quickdraw Community with ActiveCaptain, page 11).1Insert the memory card into your computer.Garmin Quickdraw Contours Mapping 11
2Access the Garmin Quickdraw Community (Connecting to the Garmin Quickdraw Community with Garmin Connect, page 11).3Select Search for Contours.4Use the map and search features to locate an area to download.The red dots represent Garmin Quickdraw Contours maps that have been shared for that region.5Select Select an Area to Download.6Drag the edges of the box to select the area to download.7Select Start Download.8Save the file to your memory card.TIP: If you cannot find the file, look in the "Downloads" folder. The browser may have saved the file there.9Remove the memory card from your computer.10Insert the memory card into the chartplotter. The chartplotter automatically recognizes the contours maps. The chartplotter may take a few minutes to load the maps.Garmin Quickdraw Contours SettingsFrom a chart, select MENU > Quickdraw Contours > Settings.Display: Displays Garmin Quickdraw Contours. The User Contours option shows your own Garmin Quickdraw Contours maps. The Community Contours option shows the maps you have downloaded from the Garmin Quickdraw Community.Recording Offset: Sets the distance between the sonar depth and the contour recording depth. If the water level has changed since your last recording, adjust this setting so the recording depth is the same for both recordings.For example, if the last time you recorded had a sonar depth of 3.1 m (10.5 ft.), and today's sonar depth is 3.6 m (12 ft.), enter -0.5 m (-1.5 ft.) for the a Recording Offset value.User Display Offset: Sets differences in contour depths and depth labels on your own contours maps to compensate for changes in the water level of a body of water, or for depth errors in recorded maps.Comm. Display Offset: Sets differences in contour depths and depth labels on the community contours maps to compensate for changes in the water level of a body of water, or for depth errors in recorded maps.Survey Coloring: Sets the color of the Garmin Quickdraw Contours display. When this setting is turned on, the colors indicate the quality of the recording. When this setting is turned off, the contour areas use standard map colors.Green indicates good depth and GPS position, and a speed under 16 km/h (10 mph). Yellow indicates good depth and GPS position, and a speed between 16 and 32 km/h (10 and 20 mph). Red indicates poor depth or GPS position, and a speed above 32 km/h (20 mph).Depth Range Shading: Specifies the upper and lower limits of a depth range and a color for that depth range.Depth Range ShadingYou can set color ranges on your map to show the water depths where your target fish are currently biting. You can set deeper ranges to monitor how quickly the bottom depth changes within a specific depth range. For inland fishing, a maximum of five depth ranges can help reduce map clutter.Red From 0 to 1.5 m (from 0 to 5 ft.)Orange From 1.5 to 3 m (from 5 to 10 ft.)Yellow From 3 to 4.5 m (from 10 to 15 ft.)Green From 4.5 to 7.6 m (from 15 to 25 ft.)Navigation with a Chartplotter CAUTIONIf your vessel has an autopilot system, a dedicated autopilot control display must be installed at each steering helm in order to disable the autopilot system.The Auto Guidance feature is based on electronic chart information. That data does not ensure obstacle and bottom clearance. Carefully compare the course to all visual sightings, and avoid any land, shallow water, or other obstacles that may be in your path.When using Go To, a direct course and a corrected course may pass over land or shallow water. Use visual sightings, and steer to avoid land, shallow water, and other dangerous objects.NOTE: Some chart views are available with premium charts, in some areas.To navigate, you must choose a destination, set a course or create a route, and follow the course or route. You can follow the course or the route on the Navigation chart, Fishing chart, Perspective 3D chart view, or Mariner’s Eye 3D chart view.You can set and follow a course to a destination using one of three methods: Go To, Route To, or Auto Guidance.Go To: Takes you directly to the destination. This is the standard option for navigating to a destination. The chartplotter creates a straight-line course or navigation line to the destination. The path may run over land and other obstacles.Route To: Creates a route from your location to a destination, allowing you to add turns along the way. This option provides a straight-line course to the destination, but allows you to add turns into the route to avoid land and other obstacles.Auto Guidance: Uses the specified information about your vessel and chart data to determine the best path to your destination. This option is available only when using a compatible premium chart in a compatible chartplotter. It provides a turn-by-turn navigation path to the destination, avoiding land and other obstacles (Auto Guidance, page 15).When you are using a compatible Garmin autopilot connected to the chartplotter using NMEA 2000®, the autopilot follows the Auto Guidance route.NOTE: Auto Guidance is available with premium charts, in some areas.12 Navigation with a Chartplotter
Basic Navigation QuestionsQuestion AnswerHow do I make the chartplotter point me in the direction in which I want to go (bearing)?Navigate using Go To (Setting and Following a Direct Course Using Go To, page 13).How do I make the device guide me along a straight line (minimizing cross track) to a location using the shortest distance from the present location?Build a single-leg route and navigate it using Route To (Creating and Navigating a Route From Your Present Location, page 14).How do I make the device guide me to a location while avoiding charted obstacles?Build a multi-leg route and navigate it using Route To (Creating and Navigating a Route From Your Present Location, page 14).How do I make the device steer my automatic pilot?Navigate using Route To (Creating and Navigating a Route From Your Present Location, page 14).Can the device create a path for me?If you have premium maps that support Auto Guidance and are in an area covered by Auto Guidance, navigate using Auto Guidance (Setting and Following an Auto Guidance Path, page 15).How do I change the Auto Guidance settings for my boat?See (Auto Guidance, page 15).DestinationsYou can select destinations using various charts and 3D chart views or using the lists.Searching for a Destination by NameYou can search for saved waypoints, saved routes, saved tracks, and marine services destinations by name.1Select Nav Info > Search by Name.2Enter at least a portion of the name of your destination.3If necessary, select Done.The 50 nearest destinations that contain your search criteria appear.4Select the destination.Selecting a Destination Using the Navigation ChartFrom the Navigation chart, select a destination.Searching for Destination Using User Data1Select Nav Info.2Select an option:• To view a list of preloaded locations and previously marked locations, select Waypoints.• To view a list of previously saved routes, select Routes & Auto Guidance Paths.• To view a list of recorded tracks, select Tracks.• To view a list of slips, moorings, and other offshore points of interest, select Offshore Services.• To view a list of marinas and other inland points of interest, select Inland Services.• To search for a destination by name, select Search by Name.3Select a destination.Searching for a Marine Services DestinationNOTE: This feature is available with premium charts, in some areas.The chartplotter contains information for thousands of destinations offering marine services.1Select Nav Info.2Select Offshore Services or Inland Services.3If necessary, select the marine service category.The chartplotter shows a list of the nearest locations and the distance and bearing to each.4Select a destination.You can select or to view additional information or to show the location on a chart.Courses CAUTIONThe Auto Guidance feature is based on electronic chart information. That data does not ensure obstacle and bottom clearance. Carefully compare the course to all visual sightings, and avoid any land, shallow water, or other obstacles that may be in your path.When using Go To, a direct course and a corrected course may pass over land or shallow water. Use visual sightings, and steer to avoid land, shallow water, and other dangerous objects.NOTE: Auto Guidance is available with premium charts, in some areas. CAUTIONGarmin recommends using Guide To only under motor power. Using Guide To while under sail can cause an unexpected gybe, risking damage to the sailboat. Unattended sails and rigging can be damaged or cause injury to any crew or passengers during an unexpected gybe maneuver.You can set and follow a course to a destination using one of three methods: Go To, Route To, or Guide To.Go To: Takes you directly to the destination. This is the standard option for navigating to a destination. The chartplotter creates a straight line course or navigation line to the destination. The path may run over land and other obstacles.Route To: Creates a route from your location to a destination, allowing you to add turns along the way. This option provides a straight line course to the destination, but allows you to add turns into the route that avoid land and other obstacles.Auto Guidance: Creates a path to a destination using Auto Guidance. This option is available only when using a compatible premium chart in a compatible chartplotter. It provides a turn-by-turn navigation line to the destination, avoiding land and other obstacles. The navigation line is based on the chart data and the safe depth, safe height, and shoreline distance user-defined chartplotter settings. Using these settings and chart data, the chartplotter creates a navigation line that avoids all areas that cannot be navigated between the present location and the destination. When you are using a compatible Garmin autopilot connected to the chartplotter using NMEA 2000, the autopilot follows the Auto Guidance route.Setting and Following a Direct Course Using Go To CAUTIONWhen using Go To, a direct course and a corrected course may pass over land or shallow water. Use visual sightings, and steer to avoid land, shallow water, and other dangerous objects.You can set and follow a direct course from your current location to a selected destination.1Select a destination (Destinations, page 13).2Select Navigate To > Go To.A magenta line appears. In the center of the magenta line is a thinner purple line that represents the corrected course from your current location to the destination. The corrected course is dynamic, and it moves with your boat when you are off course.3Follow the magenta line, steering to avoid land, shallow water, and other obstacles.Navigation with a Chartplotter 13
4If you are off course, follow the purple line (corrected course) to go to your destination, or steer back to the magenta line (direct course).Stopping NavigationFrom the Navigation chart or Fishing chart, select MENU > Stop Navigation.WaypointsWaypoints are locations you record and store in the device. Waypoints can mark where you are, where you are going, or where you have been. You can add details about the location, such as name, elevation, and depth.Marking Your Present Location as a WaypointFrom any screen, select MARK.Creating a Waypoint at a Different Location1Select Nav Info > Waypoints > Create Waypoint.2Select an option:• To create the waypoint by entering position coordinates, select Enter Coordinates, and enter the coordinates.• To create the waypoint using a chart, select Use Chart, select the location, and select SELECT.Marking an MOB or SOS LocationSelect MARK > Man Overboard.An international man overboard (MOB) symbol marks the active MOB point and the chartplotter sets a direct course back to the marked location.Viewing a List of all WaypointsSelect Nav Info > Waypoints.Editing a Saved Waypoint1Select Nav Info > Waypoints.2Select a waypoint.3Select Edit Waypoint.4Select an option:• To add a name, select Name, and enter a name.• To change the symbol, select Symbol.• To change the depth, select Depth.• To change the water temperature, select Water Temp..• To change the comment, select Comment.• To move the position of the waypoint, select Move.Browsing for and Navigating to a Saved Waypoint CAUTIONThe Auto Guidance feature is based on electronic chart information. That data does not ensure obstacle and bottom clearance. Carefully compare the course to all visual sightings, and avoid any land, shallow water, or other obstacles that may be in your path.When using Go To, a direct course and a corrected course may pass over land or shallow water. Use visual sightings, and steer to avoid land, shallow water, and other dangerous objects.NOTE: Auto Guidance is available with premium charts, in some areas.Before you can navigate to a waypoint, you must create a waypoint.1Select Nav Info > Waypoints.2Select a waypoint.3Select Navigate To.4Select an option:• To navigate directly to the location, select Go To.• To create a route to the location, including turns, select Route To.• To use Auto Guidance, select Auto Guidance.5Review the course indicated by the magenta line.NOTE: When using Auto Guidance, a gray segment within any part of the magenta line indicates that Auto Guidance cannot calculate part of the Auto Guidance line. This is due to the settings for minimum safe water depth and minimum safe obstacle height.6Follow the magenta line, steering to avoid land, shallow water, and other obstacles.Deleting a Waypoint or an MOB1Select Nav Info > Waypoints.2Select a waypoint or an MOB.3Select Delete.Deleting All WaypointsSelect Nav Info > Manage Data > Clear User Data > Waypoints > All.RoutesA route is a sequence of waypoints or locations that leads you to your final destination.Creating and Navigating a Route From Your Present LocationYou can create and immediately navigate a route on the Navigation chart or the Fishing chart. This method does not save the route or the waypoint data.1From the Navigation chart or Fishing chart, select a destination.2Select Navigate To > Route To.3Select the location of the last turn before the destination.4Select Add Turn.5If necessary, repeat to add turns, working backward from the destination to the present location of your vessel.The last turn you add should be the first turn you make, starting from your present location. It should be the turn closest to your vessel.6If necessary, select MENU.7Select Navigate Route.8Review the course indicated by the magenta line.9Follow the magenta line, steering to avoid land, shallow water, and other obstacles.Creating and Saving a RouteThis procedure saves the route and all the waypoints in it. The starting point can be your present location or another location.1Select Nav Info > Routes & Auto Guidance Paths > New > Use Chart.2Select the starting location of the route.3Follow the onscreen instructions to add a turn.4If necessary, repeat step 3 to add more turns.5Select the final destination.Viewing a List of RoutesSelect Nav Info > Routes & Auto Guidance Paths.Editing a Saved RouteYou can change the name of a route or change the turns the route contains.1Select Nav Info > Routes & Auto Guidance Paths.2Select a route.3Select Edit Route.14 Navigation with a Chartplotter
4Select an option:• To change the name, select Name, and enter the name.• To select a waypoint from the turn list, select Edit Turns > Use Turn List, and select a waypoint from the list.• To select a turn using the chart, select Edit Turns > Use Chart, and select a location on the chart.Browsing for and Navigating a Saved RouteBefore you can browse a list of routes and navigate to one of them, you must create and save at least one route.1Select Nav Info > Routes & Auto Guidance Paths.2Select a route.3Select Navigate To.4Select an option:• To navigate the route from the starting point used when the route was created, select Forward.• To navigate the route from the destination point used when the route was created, select Backward.A magenta line appears. In the center of the magenta line is a thinner purple line that represents the corrected course from your present location to the destination. The corrected course is dynamic, and it moves with your boat when you are off course.5Review the course indicated by the magenta line.6Follow the magenta line along each leg in the route, steering to avoid land, shallow water, and other obstacles.7If you are off course, follow the purple line (corrected course) to go to your destination, or steer back to the magenta line (direct course).Browsing for and Navigating Parallel to a Saved RouteBefore you can browse a list of routes and navigate to one of them, you must create and save at least one route.1Select Nav Info > Routes & Auto Guidance Paths.2Select a route.3Select Navigate To.4Select Offset to navigate parallel to the route, offset from it by a specific distance.5Indicate how to navigate the route:• To navigate the route from the starting point used when the route was created, to the left of the original route, select Forward - Port.• To navigate the route from the starting point used when the route was created, to the right of the original route, select Forward - Starboard.• To navigate the route from the destination point used when the route was created, to the left of the original route, select Backward - Port.• To navigate the route from the destination point used when the route was created, to the right of the original route, select Backward - Starboard.A magenta line appears. In the center of the magenta line is a thinner purple line that represents the corrected course from your present location to the destination. The corrected course is dynamic, and it moves with your boat when you are off course.6Review the course indicated by the magenta line.7Follow the magenta line along each leg in the route, steering to avoid land, shallow water, and other obstacles.8If you are off course, follow the purple line (corrected course) to go to your destination, or steer back to the magenta line (direct course).Deleting a Saved Route1Select Nav Info > Routes & Auto Guidance Paths.2Select a route.3Select Delete.Deleting All Saved RoutesSelect Nav Info > Manage Data > Clear User Data > Routes & Auto Guidance Paths.Auto Guidance CAUTIONThe Auto Guidance feature is based on electronic chart information. That data does not ensure obstacle and bottom clearance. Carefully compare the course to all visual sightings, and avoid any land, shallow water, or other obstacles that may be in your path.NOTE: Auto Guidance is available with premium charts, in some areas.You can use Auto Guidance to plot the best path to your destination. Auto Guidance uses your chartplotter to scan chart data, such as water depth and known obstacles, to calculate a suggested path. You can adjust the path during navigation.Setting and Following an Auto Guidance Path1Select a destination (Destinations, page 13).2Select Navigate To > Auto Guidance.3Review the path, indicated by the magenta line.4Select Start Navigation.5Follow the magenta line, steering to avoid land, shallow water, and other obstacles.NOTE: When using Auto Guidance, a gray segment within any part of the magenta line indicates that Auto Guidance cannot calculate part of the Auto Guidance line. This is due to the settings for minimum safe water depth and minimum safe obstacle height.Creating an Auto Guidance Path1Select Navigation > Routes & Auto Guidance Paths > New > Auto Guidance.2Select SELECT, and choose a destination point.Filtering a List of Routes and Auto Guidance PathsYou can filter a list of routes and Auto Guidance paths to quickly find a saved destination.1Select MENU > Filter.2Select an option.Reviewing an Auto Guidance Path1From the Navigation chart, select a path.2Select an option:• To view a hazard and adjust the hazard path, select Hazard Review.• To change the path name, or to adjust or recalculate the path, select Edit.• To delete a path, select Delete.• To navigate the selected path, select Navigate To.Adjusting an Auto Guidance Path1From the Navigation chart, follow the on-screen instructions or use the arrow keys to move the destination point to the new location.2Select SELECT > Move Point.3Select BACK to return to the navigation screen.Canceling an Auto Guidance Calculation in ProgressFrom the Navigation chart, select MENU > Cancel.Navigation with a Chartplotter 15
TIP: You can select BACK to quickly cancel the calculation.Setting a Timed ArrivalYou can use this feature on a route or an Auto Guidance path to get feedback about when you should arrive at a selected point. This allows you to time your arrival at a location, such as a bridge opening or a race starting line.1From the Navigation chart, select MENU.2If necessary, select Navigation Options.3Select Timed Arrival.TIP: You can quickly open the Timed Arrival menu by selecting a point on the path or route.Adjusting the Distance from ShoreThe Shoreline Distance setting indicates how close to the shore you want the Auto Guidance line to be placed. The Auto Guidance line may move if you change this setting while navigating. The available values for the Shoreline Distance setting are relative, not absolute. To ensure the Auto Guidance line is placed the appropriate distance from shore, you can assess the placement of the Auto Guidance line using one or more familiar destinations that require navigation through a narrow waterway.1Dock your vessel or drop the anchor.2Select Settings > Navigation > Auto Guidance > Shoreline Distance > Normal.3Select a destination that you have navigated to previously.4Select Navigate To > Auto Guidance.5Review the placement of the Auto Guidance line, and determine whether the line safely avoids known obstacles and the turns enable efficient travel.6Select an option:• If the placement of the Auto Guidance line is satisfactory, select MENU > Stop Navigation, and proceed to step 10.• If the Auto Guidance line is too close to known obstacles, select Settings > Navigation > Auto Guidance > Shoreline Distance > Far.• If the turns in the Auto Guidance line are too wide, select Settings > Navigation > Auto Guidance > Shoreline Distance > Near.7If you selected Near or Far in step 6, review the placement of the Auto Guidance line, and determine whether the line safely avoids known obstacles and the turns enable efficient travel.Auto Guidance maintains a wide clearance from obstacles in open water, even if you set the Shoreline Distance setting to Near or Nearest. As a result, the chartplotter may not reposition the Auto Guidance line, unless the destination selected requires navigation through a narrow waterway.8Select an option:• If the placement of the Auto Guidance line is satisfactory, select MENU > Stop Navigation, and proceed to step 10.• If the Auto Guidance line is too close to known obstacles, select Settings > Navigation > Auto Guidance > Shoreline Distance > Farthest.• If the turns in the Auto Guidance line are too wide, select Settings > Navigation > Auto Guidance > Shoreline Distance > Nearest.9If you selected Nearest or Farthest in step 8, review the placement of the Auto Guidance line, and determine whether the line safely avoids known obstacles and the turns enable efficient travel.Auto Guidance maintains a wide clearance from obstacles in open water, even if you set the Shoreline Distance setting to Near or Nearest. As a result, the chartplotter may not reposition the Auto Guidance line, unless the destination selected requires navigation through a narrow waterway.10Repeat steps 3 through 9 at least once more, using a different destination each time, until you are familiar with the functionality of the Shoreline Distance setting.Auto Guidance Path Configurations CAUTIONThe Preferred Depth and Vertical Clearance settings influence how the chartplotter calculates an Auto Guidance path. If an area has an unknown water depth or an unknown obstacle height, the Auto Guidance path is not calculated in that area. If an area at the beginning or the end of an Auto Guidance path is shallower than the Preferred Depth or lower than the Vertical Clearance settings, the Auto Guidance path may not be calculated in that area, depending on the map data. On the chart, the course through those areas appears as a gray line or a magenta and gray striped line. When your boat enters one of those areas, a warning message appears.NOTE: Auto Guidance is available with premium charts, in some areas.NOTE: Not all settings apply to all maps.You can set the parameters the chartplotter uses when calculating an Auto Guidance path.Preferred Depth: Sets the minimum water depth, based on chart depth data, that your boat can safely travel over.NOTE: The minimum water depth for the premium charts (made before 2016) is 3 feet. If you enter a value of less than 3 feet, the charts only use depths of 3 feet for Auto Guidance path calculations.Vertical Clearance: Sets the minimum height of a bridge or obstacle, based on chart data, that your boat can safely travel under.Shoreline Distance: Sets how close to the shore you want the Auto Guidance path to be placed. The Auto Guidance path may move if you change this setting while navigating. The available values for this setting are relative, not absolute. To ensure that the Auto Guidance line is placed the appropriate distance from shore, you can assess the placement of the Auto Guidance path using one or more familiar destinations that require navigation through a narrow waterway (Adjusting the Distance from Shore, page 16).TracksA track is a recording of the path of your boat. The track currently being recorded is called the active track, and it can be saved. You can show tracks in each chart or 3D chart view.Showing TracksSelect Nav Info > Tracks > Tracks.A trailing line on the chart indicates your track.Setting the Color of the Active Track1Select Nav Info > Tracks > Active Track Options > Track Color.2Select a track color.Saving the Active TrackThe track currently being recorded is called the active track.1Select Nav Info > Tracks > Save Active Track.2Select an option:• Select the time the active track began.• Select Entire Log.Viewing a List of Saved TracksSelect Nav Info > Tracks > Saved Tracks.16 Navigation with a Chartplotter
Editing a Saved Track1Select Nav Info > Tracks > Saved Tracks.2Select a track.3Select Edit Track.4Select an option:• Select Name, and enter the new name.• Select Track Color, and select a color.Saving a Track as a Route1Select Nav Info > Tracks > Saved Tracks.2Select a track.3Select Edit Track > Save As > Save as Route.Browsing for and Navigating a Recorded TrackBefore you can browse a list of tracks and navigate to them, you must record and save at least one track (Tracks, page 16).1Select Nav Info > Tracks > Saved Tracks.2Select a track.3Select Follow Track.4Select an option:• To navigate the track from the starting point used when the track was created, select Forward.• To navigate the track from the destination point used when the track was created, select Backward.5Review the course indicated by the colored line.6Follow the line along each leg in the route, steering to avoid land, shallow water, and other obstacles.Deleting a Saved Track1Select Nav Info > Tracks > Saved Tracks.2Select a track.3Select Delete.Deleting All Saved TracksSelect Nav Info > Manage Data > Clear User Data > Saved Tracks.Retracing the Active TrackThe track currently being recorded is called the active track.1Select Nav Info > Tracks > Follow Active Track.2Select an option:• Select the time the active track began.• Select Entire Log.3Review the course indicated by the colored line.4Follow the colored line, steering to avoid land, shallow water, and other obstacles.Clearing the Active TrackSelect Nav Info > Tracks > Clear Active Track.The track memory is cleared, and the active track continues to be recorded.Managing the Track Log Memory During Recording1Select Nav Info > Tracks > Active Track Options.2Select Record Mode.3Select an option:• To record a track log until the track memory is full, select Fill.• To continuously record a track log, replacing the oldest track data with new data, select Wrap.Configuring the Recording Interval of the Track LogYou can indicate the frequency at which the track plot is recorded. Recording more frequent plots is more accurate but fills the track log faster. The resolution interval is recommended for the most efficient use of memory.1Select Nav Info > Tracks > Active Track Options > Record Interval > Interval.2Select an option:• To record the track based on a distance between points, select Distance > Change, and enter the distance.• To record the track based on a time interval, select Time > Change, and enter the time interval.• To record the track plot based on a variance from your course, select Resolution > Change, and enter the maximum error allowed from the true course before recording a track point.BoundariesBoundaries allow you to avoid or remain in designated areas in a body of water. You can set an alarm to alert you when you enter or exit a boundary.You can create boundary areas, lines, and circles using the map. You can also convert saved tracks and routes into boundary lines. You can create a boundary area using waypoints by creating a route from the waypoints, and converting the route into a boundary line.You can select a boundary to act as the active boundary. You can add the active boundary data to the data fields on the chart.Creating a Boundary1Select Nav Info > Boundaries > New Boundary.2Select a boundary shape.3Follow the on-screen instructions.Boundary Display SettingsSelect Nav Info > Boundaries > Display Options.Distance/Bearing: Allows you to hide or display the bearing and distance to your destination for the active boundary.Chart Display: Allows you to hide or display boundaries on the chart.Color: Sets the color of boundaries on the chart.Converting a Route to a BoundaryBefore you can convert a route to a boundary, you must create and save at least one route (Creating and Saving a Route, page 14).1Select Nav Info > Routes & Auto Guidance Paths.2Select a route.3Select Edit Route > Save as Boundary.Converting a Track to a BoundaryBefore you can convert a track to a boundary, you must record and save at least one track (Saving the Active Track, page 16).1Select Nav Info > Tracks > Saved Tracks.2Select a track.3Select Edit Track > Save As > Save as Boundary.Editing a Boundary1Select Nav Info > Boundaries.2Select a boundary.3Select Edit Boundary.4Select an option:• To edit the appearance of the boundary on the chart, select Display Options.• To change the boundary lines or name, select Edit Boundary.• To edit the boundary alarm, select Alarm.Navigation with a Chartplotter 17
Setting a Boundary AlarmBoundary alarms alert you when you are within a specified distance of a set boundary.1Select Nav Info > Boundaries.2Select a boundary.3Select Alarm > On.4Enter a distance.5Select an option.• To set an alarm to sound when your boat is a specified distance from the boundary of an area that you want to stay within, select Exiting.• To set an alarm to sound when your boat is a specified distance from the boundary of an area that you want to avoid, select Entering.Deleting a Boundary1Select Nav Info > Boundaries.2Select a boundary.3Select Edit Boundary > Delete.Sonar FishfinderWhen properly connected to a compatible transducer, your ECHOMAP Plus device can be used as a fishfinder.For more information about which transducer is best for your needs, go to garmin.com/transducers.Different sonar views can help you view the fish in the area. The sonar views available vary depending on the type of transducer and sounder module connected to the chartplotter. For example, you can view Garmin ClearVü™ sonar screens only if you have a compatible Garmin ClearVü transducer connected.There are four basic styles of sonar views available: a full-screen view, a split-screen view that combines two or more views, a split-zoom view, and a split-frequency view that displays two different frequencies. You can customize the settings for each view in the screen. For example, if you are viewing the split-frequency view, you can separately adjust the gain for each frequency.If you do not see an arrangement of sonar views to suit your needs, you can create a custom combination screen (Creating a New Combination Page with the ECHOMAP Plus 70/90, page 2).Stopping the Transmission of Sonar SignalsFrom a sonar screen, select MENU > Transmit.Changing the Sonar View1From a combination screen with sonar, select MENU > Edit Combination.2Select the window to change.3Select a sonar view.Traditional Sonar ViewThere are several full-screen views available, depending on the transducer that is connected.The full-screen Traditional sonar view shows a large image of the sonar readings from a transducer. The range scale along the right side of the screen shows the depth of detected objects as the screen scrolls from the right to the left.ÀDepth informationÁSuspended targets or fishÂBottom of the body of waterSplit-Frequency Sonar ViewIn the split-frequency sonar view, one side of the screen shows a full-view graph of high frequency sonar data, and the other side of the screen shows a full-view graph of lower frequency sonar data.NOTE: The split-frequency sonar view requires the use of a dual-frequency transducer.Split-Zoom Sonar ViewThe split-zoom sonar view shows a full-view graph of sonar readings, and a magnified portion of that graph, on the same screen.Garmin ClearVü Sonar ViewNOTE: To receive Garmin ClearVü scanning sonar, you need a compatible chartplotter or fishfinder and a compatible transducer. For information about compatible transducers, go to garmin.com/transducers.Garmin ClearVü high-frequency sonar provides a detailed picture of the fishing environment around the boat in a detailed representation of structures the boat is passing over.Traditional transducers emit a conical beam. The Garmin ClearVü scanning sonar technology emits two narrow beams, similar to the shape of the beam in a copying machine. These beams provide a clearer, picture-like image of what is beneath the boat.SideVü Sonar ViewNOTE: Not all models provide built-in SideVü sonar support. If your model does not provide built-in SideVü sonar, you need a compatible sounder module and compatible SideVü transducer.If your model does provide built-in SideVü sonar, you need a compatible SideVü transducer.SideVü scanning sonar technology shows you a picture of what lies to the sides of the boat. You can use this as a search tool to find structures and fish.18 Sonar Fishfinder
ÀLeft side of the boatÁRight side of the boatÂThe transducer on your vesselÃTreesÄOld tiresÅLogsÆDistance from the side of the boatÇWater between the vessel and the bottomSideVü Scanning TechnologyInstead of a more common conical beam, the SideVü transducer uses a flat beam to scan the water and bottom to the sides of your boat.Panoptix Sonar ViewsNOTE: Not all models support Panoptix transducers.To receive Panoptix sonar, you need a compatible chartplotter and a compatible transducer.The Panoptix sonar views allow you to see all around the boat in real time. You can also watch your bait underwater and bait schools in front of or below your boat.The LiveVü sonar views provide you a view of the live movement either in front of or below your boat. The screen updates very quickly, producing sonar views that look more like live video.The RealVü 3D sonar views provide three-dimensional views of either what is in front of or below your boat. The screen updates with each sweep of the transducer.To see all five Panoptix sonar views, you need one transducer to show the down views and a second transducer to show the forward views.To access the Panoptix sonar views, select Sonar, and select a view.LiveVü Down Sonar ViewThis sonar view shows a two-dimensional view of what is below the boat and can be used to see a bait ball and fish.ÀPanoptix down view history in a scrolling sonar viewÁBoatÂRangeÃTrailsÄDrop shot rigÅBottomLiveVü Forward Sonar ViewThis sonar view shows a two-dimensional view of what is in front of the boat and can be used to see a bait ball and fish.ÀBoatÁRangeÂFishÃTrailsÄBottomRealVü 3D Forward Sonar ViewThis sonar view shows a three-dimensional view of what is in front of the transducer. This view can be used when you are stationary and you need to see the bottom and the fish approaching the boat.ÀColor legendÁBoatÂPing indicatorÃFishÄBottomÅRangeSonar Fishfinder 19
RealVü 3D Down Sonar ViewThis sonar view shows a three-dimensional view of what is below the transducer and can be used when you are stationary and want to see what is around your boat.RealVü 3D Historical Sonar ViewThis sonar view provides a three-dimensional view of what is behind your boat as you are moving and shows the entire water column in 3D, from the bottom to the top of the water. This view is used for finding fish.ÀColor legendÁBoatÂRangeÃBottomÄStructureÅFishFrontVü Sonar ViewThe Panoptix FrontVü sonar view increases your situational awareness by showing obstructions under the water, up to 91 meters (300 feet) in front of the boat.The ability to effectively avoid forward collisions with FrontVü sonar decreases as your speed rises above 8 knots.To see the FrontVü sonar view, you must install and connect a compatible transducer, such as a PS21 transducer. You may need to update the transducer software.Selecting the Transducer TypeIf you are connecting a transducer that was not included with the device, you may need to set the transducer type to make the sonar function properly. Before connecting the transducer, you should select the transducer type. The transducer name should be listed on the label on the transducer cable, near the connector.This device is compatible with a range of accessory transducers, including Garmin ClearVü transducers, which are available at garmin.com/transducers.1Select Settings > My Vessel > Transducer Type.2Select an option:• If you have a 200/77 kHz, dual-beam transducer, select Dual Beam (200/77 kHz).• If you have a 200/50 kHz, dual-frequency transducer, select Dual Frequency (200/50 kHz).• If you have another type of transducer, select it from the list.Calibrating the CompassBefore you can calibrate the compass, the transducer must be installed on the shaft far enough away from the trolling motor to avoid magnetic interference, and deployed in the water. Calibration must be of sufficient quality to enable the internal compass.NOTE: To use the compass, you must mount the transducer on the shaft. The compass does not work when you mount the transducer on the motor.NOTE: Compass calibration is available only for transducers with an internal compass, such as the PS21-TR transducer.You can begin turning your boat before calibrating, but you must fully rotate your boat 1.5 times during calibration.1From an applicable sonar view, select MENU > Sonar Setup > Installation.2If necessary, select Use AHRS to turn on the AHRS sensor.3Select Calibrate Compass.4Follow the on-screen instructions.Creating a Waypoint on the Sonar Screen1From a sonar view, select MENU > Pause Sonar.2Select a location.3Select New Waypoint or SELECT.4If necessary, edit the waypoint information, such as the waypoint name.Pausing the Sonar DisplayFrom a sonar view, select MENU > Pause Sonar.Viewing Sonar HistoryYou can scroll the sonar display to view historical sonar data.NOTE: Not all transducers save historical sonar data.1From a sonar view, hold to scroll through the history.2From a sonar view, drag the screen to the right.3Select BACK to exit history.Sonar SharingThis feature may not be available on all chartplotter models.You can view the sonar data from other chartplotters with a built-in sonar module connected on the Garmin Marine Network.Each chartplotter on the network can display sonar data from every compatible sonar module and transducer on the network, no matter where the chartplotters and transducers are mounted on your boat. For example, from a transducer with Garmin ClearVü mounted at the back of the boat, you can view the sonar data using the 93sv mounted at the front of your boat.When sharing sonar data, the values of some sonar settings, such as Range and Gain, are synchronized across the devices on the network. The values of other sonar settings, such as the Appearance settings, are not synchronized and should be configured on each individual device. In addition, the scroll rates of the various traditional and Garmin ClearVü sonar views are synchronized to make the split views more cohesive.NOTE: Using multiple transducers simultaneously can create cross talk, which can be removed by adjusting the Interference sonar setting.Selecting a Sonar SourceThis feature may not be available with all models.When you are using more than one sonar data source for a particular sonar view, you can select the source to use for that sonar view. For example, if you have two sources for Garmin ClearVü, you can select the source to use from the Garmin ClearVü sonar view.20 Sonar Fishfinder
1Open the sonar view for which you will change the source.2Select MENU > Sonar Setup > Source.3Select the source for this sonar view.Renaming a Sonar SourceYou can rename a sonar source to easily identify that source. For example, you use "Bow" as the name of the transducer on the bow of your boat.The source is renamed for the present view only. For example, to rename the Garmin ClearVü sonar source, you must open the Garmin ClearVü sonar view.1From the sonar view, select MENU > Sonar Setup > Source > Rename Sonar Sources.2Enter the name.Adjusting the Level of DetailYou can control the level of detail and noise shown on the sonar screen either by adjusting the gain for traditional transducers or by adjusting the brightness for Garmin ClearVü transducers.If you want to see the highest intensity signal returns on the screen, you can lower the gain or brightness to remove lower intensity returns and noise. If you want to see all return information, you can increase the gain or brightness to see more information on the screen. This also increases noise, and can make it more difficult to recognize actual returns.1From a sonar view, select MENU.2Select Gain or Brightness.3Select an option:• To increase or decrease the gain or brightness manually, select Up or Down.• To allow the chartplotter to adjust the gain or brightness automatically, select an automatic option.Adjusting the Color IntensityYou can adjust the intensity of colors and highlight areas of interest on the sonar screen by adjusting the color gain for traditional transducers or the contrast for Garmin ClearVü and SideVü/ClearVü transducers. This setting works best after you have adjusted the level of detail shown on the screen using the gain or brightness settings.If you want to highlight smaller fish targets or create a higher intensity display of a target, you can increase the color gain or contrast setting. This causes a loss in the differentiation of the high intensity returns at the bottom. If you want to reduce the intensity of the return, you can reduce the color gain or contrast.1From a sonar view, select MENU.2Select an option:• While in the Garmin ClearVü or SideVü sonar view, select Contrast.• While in a Panoptix LiveVü sonar view, select Color Gain.• While in another sonar view, select Sonar Setup > Advanced > Color Gain.3Select an option:• To increase or decrease the color intensity manually, select Up or Down.• To use the default setting, select Default.Sonar RecordingsRecording the Sonar DisplayNOTE: Not all models support sonar recording.1Insert a memory card into the card slot.2From a sonar view, select MENU > Sonar Setup > Sonar Recording > Record Sonar.15 minutes of sonar recording uses approximately 200 MB of space of the inserted memory card. You can record sonar until the card reaches capacity.Stopping the Sonar RecordingBefore you can stop recording sonar, you must begin recording it (Recording the Sonar Display, page 21).From a sonar view, select MENU > Sonar Setup > Sonar Recording > Stop Recording.Deleting a Sonar Recording1Insert a memory card into the card slot.2From a sonar view, select MENU > Sonar Setup > Sonar Recordings > View Recordings.3Select a recording.4Select Delete.Playing Sonar RecordingsBefore you can play back the sonar recordings, you must download and install the HomePort™ application and record sonar data onto a memory card.1Remove the memory card from the device.2Insert the memory card into a card reader attached to a computer.3Open the HomePort application.4Select a sonar recording from your device list.5Right-click the sonar recording in the lower pane.6Select Playback.Traditional, Garmin ClearVü, and SideVü Sonar SetupNOTE: Not all options and settings apply to all models, sounder modules, and transducers.From a sonar view, select MENU > Sonar Setup.Depth Line: Shows a quick-reference depth line.Scroll Speed: Sets the rate at which the sonar scrolls from right to left.In shallow water you might want to slow the scroll speed to extend the length of time the information is displayed on screen. In deeper water you can increase the scroll speed.On-screen Control: Sets the behavior of the buttons on the sonar screen control. This is available for touchscreen devices.Range Lines: Shows the vertical lines indicating the distance to the right and left of the boat. This setting is available for SideVü sonar view.Color Scheme: Sets the color scheme of the sonar view. This setting might be available in the Appearance menu.The high contrast color schemes provide darker color assignments to the low intensity returns. The low contrast color schemes provide color assignments to the low intensity returns that are similar to the background color.Appearance: See Sonar Appearance Settings, page 22.Overlay Numbers: Sets the data shown on the sonar screen.Advanced: See Advanced Sonar Settings, page 22.Installation: Restores the default sonar settings.Setting the Zoom Level on the Sonar Screen1From a sonar view, select MENU > Zoom.2Select an option:• To zoom in on the sonar data from the bottom depth, select Bottom Lock.• To set the depth range of the magnified area manually, select Manual, select View Up or View Down to set the Sonar Fishfinder 21
depth range of the magnified area, and select Zoom In or Zoom Out to increase or decrease the magnification of the magnified area.• To set the depth and zoom automatically, select Auto.• To cancel the zoom, select No Zoom.Setting the Scroll SpeedYou can set the rate at which the sonar image moves across the screen. A higher scroll speed shows more detail, especially while moving or trolling. A lower scroll speed displays sonar information on the screen longer. Setting the scroll speed on one sonar view applies to all the sonar views.1From a sonar view, select MENU > Sonar Setup > Scroll Speed.2Select an option:• To adjust the scroll speed automatically using speed-over-ground or water speed data, select Auto.The Auto setting selects a scroll rate to match the boat speed, so targets in the water are drawn with the correct aspect ratio and appear less distorted. When viewing Garmin ClearVü or SideVü sonar views, it is recommend to use the Auto setting.• To use a very fast scroll speed, select Ultrascroll®.The Ultrascroll option quickly scrolls new sonar data, but with a reduced image quality. For most situations, the Fast option provides a good balance between a quickly scrolling image and targets that are less distorted.Adjusting the Range of the Depth or Width ScaleYou can adjust the range of the depth scale traditional and Garmin ClearVü sonar views and the range of the width scale for the SideVü sonar view.Allowing the device to adjust the range automatically keeps the bottom within the lower or outer third of the sonar screen, and can be useful for tracking a bottom that has minimal or moderate terrain changes.Manually adjusting the range enables you to view a specified range, which can be useful for tracking a bottom that has large terrain changes, such as a drop-offs or cliffs. The bottom can appear on the screen as long as it appears within the range you have set.1From a sonar view, select MENU > Range.2Select an option:• To allow the chartplotter to adjust the range automatically, select Auto.• To increase or decrease the range manually, select Up or Down.TIP: From the sonar screen, you can select or to manually adjust the range.TIP: When viewing multiple sonar screens, you can select SELECT to choose the active screen.Sonar Appearance SettingsFrom a sonar view, select MENU > Sonar Setup > Appearance.Color Scheme: Sets the color scheme.Edge: Highlights the strongest signal from the bottom to help define the hardness or softness of the signal.A-Scope: Displays a vertical flasher along the right side of the screen that shows instantaneously the range to targets along a scale.Pic. Advance: Allows the sonar picture to advance faster by drawing more than one column of data on the screen for each column of sounder data received. This is especially helpful when you are using the sounder in deep water, because the sonar signal takes longer to travel to the water bottom and back to the transducer.The 1/1 setting draws one column of information on the screen per sounder return. The 2/1 setting draws two columns of information on the screen per sounder return, and so on for the 4/1 and 8/1 settings.Fish Symbols: Sets how the sonar interprets suspended targets.Sonar AlarmsNOTE: Not all options are available on all transducers.From an applicable sonar view, select MENU > Sonar Setup > Alarms.You can also open the sonar alarms by selecting Settings > Alarms > Sonar.Shallow Water: Sets an alarm to sound when the depth is less than the specified value.Deep Water: Sets an alarm to sound when the depth is greater than the specified value.FrontVü Alarm: Sets an alarm to sound when the depth in front of the vessel is less than the specified value, which can help you avoid running aground (Setting the FrontVü Depth Alarm, page 24). This alarm is available only with Panoptix FrontVü transducers.Water Temp.: Sets an alarm to sound when the transducer reports a temperature that is 2°F (1.1°C) above or below the specified temperature.Contour: Sets an alarm to sound when the transducer detects a suspended target within the specified depth from the surface of the water and from the bottom.Fish: Sets an alarm to sound when the device detects a suspended target.• sets the alarm to sound when fish of all sizes are detected.• sets the alarm to sound only when medium or large fish are detected.• sets the alarm to sound only when large fish are detected.Advanced Sonar SettingsNOTE: Not all options and settings apply to all models and transducers.From a sonar view, select MENU > Sonar Setup > Advanced.Interference: Adjusts the sensitivity to reduce the effects of interference from nearby sources of noise.The lowest interference setting that achieves the desired improvement should be used to remove interference from the screen. Correcting installation issues that cause noise is the best way to eliminate interference.Surface Noise: Hides surface noise to help reduce clutter. Wider beam widths (lower frequencies) can show more targets, but can generate more surface noise.Color Gain: See Adjusting the Level of Detail, page 21.TVG: Adjusts the appearance of returns to compensate for weakened sonar signals in deeper water, and reduces the appearance of noise near the surface. When the value of this setting is increased, the colors associated with low-level noise and fish targets appear more consistent through various water depths. This setting also reduces the noise near the surface of the water.Transducer Installation SettingsNOTE: Not all options and settings apply to all models and transducers.From a sonar view, select MENU > Sonar Setup > Installation.22 Sonar Fishfinder
Restore Sonar Defaults: Restores the factory default settings for the sonar view.Transducer Type: Allows you to select the type of transducer that is connected to the device.Shift: Allows you to set the depth range on which the sonar is focused. This enables you to zoom in to an area within the focused depth.Flip Left/Right: Changes the orientation of the SideVü sonar view when the transducer is installed backward.Flipped: Sets the orientation of the Panoptix sonar view when the transducer is installed with the cables pointing toward the port side of the boat.Beam Width: Sets the width of the Panoptix transducer beam.Narrow beam widths allow you to see deeper and farther. Wider beam widths allow you to see more coverage area.Use AHRS: Allows the internal attitude heading and reference system (AHRS) sensors to detect the installation angle of the Panoptix transducer. When this setting is turned off, it is assumed the transducer is installed at a 45-degree angle.Sonar FrequenciesNOTE: The frequencies available depend on the chartplotter, sounder modules, and transducer being used.Adjusting the frequency helps adapt the sonar for your particular goals and the present depth of the water.Higher frequencies use narrow beam widths, and are better for high-speed operation and rough sea conditions. Bottom definition and thermocline definition can be better when using a higher frequency.Lower frequencies use wider beam widths, which can let the fisherman see more targets, but could also generate more surface noise and reduce bottom signal continuity during rough sea conditions. Wider beam widths generate larger arches for fish target returns, making them ideal for locating fish. Wider beam widths also perform better in deep water, because the lower frequency has better deep water penetration.CHIRP frequencies allow you to sweep each pulse through a range of frequencies, resulting in better target separation in deep water. CHIRP can be used to distinctly identify targets, like individual fish in a school, and for deep water applications. CHIRP generally performs better than single frequency applications. Because some fish targets may show up better using a fixed frequency, you should consider your goals and water conditions when using CHIRP frequencies.Some sonar black boxes and transducers also provide the ability to customize preset frequencies for each transducer element, which enables you to change the frequency quickly using the presets as the water and your goals change.Viewing two frequencies concurrently using the split-frequency view allows you to see deeper with the lower frequency return and, at the same time, see more detail from the higher frequency return.Selecting FrequenciesNOTE: You cannot adjust the frequency for all sonar views and transducers.You can indicate which frequencies appear on the sonar screen.1From a sonar view, select MENU > Frequency.2Select a frequency suited to your needs and water depth.For more information on frequencies, see Sonar Frequencies, page 23.Creating a Frequency PresetNOTE: Not available with all transducers.You can create a preset to save a specific sonar frequency, which allows you to change frequencies quickly.1From a sonar view, select MENU > Frequency.2Select Add.3Enter a frequency.Turning On the A-ScopeNOTE: This feature is available in the Traditional sonar views.The a-scope is a vertical flasher along the right side of the view, showing you what is underneath the transducer right now. You can use the a-scope to identify target returns that may be missed when the sonar data is quickly scrolling across the screen, such as when your boat is moving at high speeds. It can also be helpful for detecting fish that are close to the bottom.The a-scope above shows fish returns À and a soft bottom return Á.1From a sonar view, select MENU > Sonar Setup > Appearance > A-Scope.2Select a hold time.You can increase the hold time to increase the length of time the sonar returns are displayed.Panoptix Sonar SetupAdjusting the RealVü Viewing Angle and Zoom LevelYou can change the viewing angle of the RealVü sonar views. You can also zoom in and out of the view.From a RealVü sonar view, select an option:• To adjust the viewing angle, use the arrow keys.• To zoom in and out, turn the knob.Adjusting the RealVü Sweep SpeedYou can update how quickly the transducer sweeps back and forth. A faster sweep rate creates a less detailed image, but the screen refreshes faster. A slower sweep rate creates a more detailed image, but the screen refreshes more slowly.NOTE: This feature is not available for the RealVü 3D Historical sonar view.1From a RealVü sonar view, select MENU > Sweep Speed.2Select an option.LiveVü Forward and FrontVü Sonar MenuFrom the LiveVü Forward or FrontVü sonar view, select MENU.Gain: Controls the level of detail and noise shown on the sonar screen.If you want to see the highest intensity signal returns on the screen, you can lower the gain to remove lower intensity returns and noise. If you want to see all return information, you can increase the gain to see more information on the screen. This also increases noise, and can make it more difficult to recognize actual returns.Depth Range: Adjusts the range of the depth scale.Allowing the device to adjust the range automatically keeps the bottom within the lower portion of the sonar screen, and can be useful for tracking a bottom that has minimal or moderate terrain changes.Manually adjusting the range enables you to view a specified range, which can be useful for tracking a bottom that has large terrain changes, such as a drop-offs or cliffs. The Sonar Fishfinder 23
bottom can appear on the screen as long as it appears within the range you have set.Forward Range: Adjusts the range of the forward scale.Allowing the device to adjust the range automatically adjusts the forward scale in relation to the depth. Manually adjusting the range enables you to view a specified range. The bottom can appear on the screen as long as it appears within the range you have set. Manually reducing this option can reduce the effectiveness of the FrontVü Alarm, reducing your reaction time to low depth readings.Transmit Angle: Adjusts the focus of the transducer to the port or starboard side. This is available only with RealVü capable Panoptix FrontVü transducers, such as the PS30, PS31, and PS60.Transmit: Stops the transducer from transmitting.FrontVü Alarm: Sets an alarm to sound when the depth in front of the vessel is less than the specified value (Setting the FrontVü Depth Alarm, page 24). This is available only with Panoptix FrontVü transducers.Sonar Setup: Adjusts the setup of the transducer and the appearance of the sonar returns.Edit Overlays: Adjusts the data shown on the screen.Setting the LiveVü and FrontVü Transducer Transmit AngleThis feature is available only with Panoptix LiveVü and FrontVü transducers.You can change the transducer transmit angle to aim the transducer at a particular area of interest. For example, you might aim the transducer to follow a bait ball or focus on a tree as you pass it.1From a LiveVü or FrontVü sonar view, select MENU > Transmit Angle.2Select an option.Setting the FrontVü Depth Alarm WARNINGThe FrontVü depth alarm is a tool for situational awareness only, and may not prevent groundings in all circumstances. It is the obligation of the vessel operator to ensure safe operation of the vessel.This alarm is available only with Panoptix FrontVü transducers.You can set an alarm to sound when the depth is below a specified level. For best results, you should set the bow offset when using the front collision alarm (Setting the Bow Offset, page 25).1From the FrontVü sonar view, select MENU > FrontVü Alarm.2Select On.3Enter the depth at which the alarm is triggered, and select Done.On the FrontVü screen, a depth line shows the depth at which the alarm is set. The line is green when you are in a safe depth. The line turns yellow when you are going faster than the forward range gives you time to react (10 seconds). It turns red and sounds an alarm when the system detects an obstruction or the depth is less than the entered value. CAUTIONThe ability to effectively avoid running aground with FrontVü sonar decreases as your speed rises above 8 knots.LiveVü and FrontVü Appearance SettingsFrom a LiveVü or FrontVü Panoptix sonar view, select MENU > Sonar Setup > Appearance.Color Scheme: Sets the color palette.Color Gain: Adjusts the intensity of colors shown on the screen.You can select a higher color gain value to see targets higher in the water column. A higher color gain value also allow you to differentiate low intensity returns higher in the water column, but this causes a loss in the differentiation of the returns at the bottom. You can select a lower color gain value when targets are near the bottom, to help you distinguish between targets and high intensity returns such as sand, rock, and mud.Trails: Sets the how long the trails appear on the screen. The trails show the movement of the target.Bottom Fill: Colors the bottom brown to distinguish it from the water returns.Grid Overlay: Shows a grid of range lines.Scroll History: Shows the sonar history in a traditional sonar view.RealVü Appearance SettingsFrom a RealVü sonar view, select MENU > Sonar Setup > Appearance.Point Colors: Sets a different color palette for the sonar return points.Bottom Colors: Sets the color scheme for the bottom.Bottom Style: Sets the style for the bottom. When you are in deep water, you can select the Points option and manually set the range to a shallower value.Color Key: Shows a legend of the depths the colors represent.Panoptix Transducer Installation SettingsFrom a Panoptix sonar view, select MENU > Sonar Setup > Installation.Install Depth: Sets the depth below the water line where the Panoptix transducer is mounted. Entering the actual depth at which the transducer is mounted results in a more accurate visual presentation of what is in the water.Bow Offset: Sets the distance between the bow and the forward view Panoptix transducer installation location. This allows you to view the forward distance from the bow instead of the transducer location.This applies to Panoptix transducers in the FrontVü, LiveVü Forward, and RealVü 3D Forward sonar views.Beam Width: Sets the width of the down view Panoptix transducer beam. Narrow beam widths allow you to see deeper and farther. Wider beam widths allow you to see more coverage area.This applies to Panoptix transducers in the FrontVü, LiveVü Down, and LiveVü Forward sonar views.Use AHRS: Enables the internal attitude heading and reference system (AHRS) sensors to detect the installation angle of the Panoptix transducer automatically. When this setting is turned off, you can enter the specific installation angle for the transducer using the Pitch Angle setting. Many forward view transducers are installed at a 45-degree angle and down view transducers are installed at a zero-degree angle.Flipped: Sets the orientation of the Panoptix sonar view when the down view transducer is installed with the cables pointing toward the port side of the boat.This applies to Panoptix transducers in the LiveVü Down, RealVü 3D Down, and RealVü 3D Historical sonar views.Calibrate Compass: Calibrates the internal compass in the Panoptix transducer (Transducer Installation Settings, page 22).This applies to Panoptix transducers with an internal compass, such as the PS21-TR transducer.Restore Sonar Defaults: Restores the sonar settings to the factory default values.24 Sonar Fishfinder
Setting the Bow OffsetFor forward view Panoptix transducers, you can enter a bow offset to compensate the forward distance readings for the transducer installation location. This allows you to view the forward distance from the bow instead of the transducer installation location.This feature applies to Panoptix transducers in the FrontVü, LiveVü Forward, and RealVü 3D Forward sonar views.1Measure the horizontal distance À from the transducer to the bow.2From an applicable sonar view, select MENU > Sonar Setup > Installation > Bow Offset.3Enter the distance measured, and select Done.On the applicable sonar view, the forward range shifts by the distance you entered.Autopilot WARNINGYou can use the autopilot feature only at a station installed next to a helm, throttle, and helm control device.You are responsible for the safe and prudent operation of your vessel. The autopilot is a tool that enhances your capability to operate your boat. It does not relieve you of the responsibility of safely operating your boat. Avoid navigational hazards and never leave the helm unattended.Always be prepared to promptly regain manual control of your boat.Learn to operate the autopilot on calm and hazard-free open water.Use caution when operating the autopilot near hazards in the water, such as docks, pilings, and other boats.NOTE: This feature is only available on models with NMEA 2000 network capabilities.The autopilot system continuously adjusts the steering of your boat to maintain a constant heading (heading hold). The system also allows manual steering and several modes of automatic-steering functions and patterns.When the compatible chartplotter is connected to a compatible Garmin autopilot system, you can engage and control the autopilot from the chartplotter.For information about compatible Garmin autopilot systems, go to garmin.com.Autopilot ScreenÀActual headingÁIntended heading (heading the autopilot is steering toward)ÂActual heading (when in standby mode)Intended heading (when engaged)ÃRudder position indicator (This functionality is available only when a rudder sensor is connected.)Adjusting the Step Steering Increment1From the Autopilot screen, select MENU > Autopilot Setup > Step Turn Size.2Select an increment.Setting the Power SaverYou can adjust the level of rudder activity.1From the autopilot screen, select MENU > Autopilot Setup > Power Mode Setup > Power Saver.2Select a percentage.Selecting a higher percentage reduces rudder activity and heading performance. The higher the percentage, the more the course deviates before the autopilot corrects it.TIP: In choppy conditions at low speeds, increasing the Power Saver percentage reduces rudder activity.Engaging the AutopilotWhen you engage the autopilot, the autopilot takes control of the helm and steers the boat to maintain your heading.From any screen, select Engage.Your intended heading shows in the center of the Autopilot screen.Steering Patterns WARNINGYou are responsible for the safe operation of your boat. Do not begin a pattern until you are certain that the water is clear of obstacles.The autopilot can steer the boat in preset patterns for fishing, and it can also perform other specialty maneuvers such as U-turns and Williamson turns.Following the U-Turn PatternYou can use the u-turn pattern to turn the boat around 180 degrees and maintain the new heading.1From the autopilot screen, select MENU > Pattern Steering > U-Turn.2Select Engage Port or Engage Starboard.Setting Up and Following the Circles PatternYou can use the circles pattern to steer the boat in a continuous circle, in a specified direction, and at a specified time interval.1From the autopilot screen, select MENU > Pattern Steering > Circles.2If necessary, select Time, and select a time for the autopilot to steer one complete circle.3Select Engage Port or Engage Starboard.Autopilot 25
Setting Up and Following the Zigzag PatternYou can use the zigzag pattern to steer the boat from port to starboard and back, over a specified time and angle, across your present heading.1From the autopilot screen, select MENU > Pattern Steering > Zigzag.2If necessary, select Amplitude, and select a degree.3If necessary, select Period, and select a length of time.4Select Engage Zigzag.Following the Williamson Turn PatternYou can use the Williamson turn pattern to steer the boat around with the intent of running alongside the location where the Williamson turn pattern was initiated. The Williamson turn pattern can be used in man overboard situations.1From the autopilot screen, select MENU > Pattern Steering > Williamson Turn.2Select Engage Port or Engage Starboard.Sailing FeaturesSetting the Vessel TypeYou can select your boat type to configure the chartplotter settings and to use features customized for your boat type.1Select Settings > My Vessel > Vessel Type.2Select an option.Sail RacingYou can use the device to increase the likelihood that your boat will cross the start line of a race exactly when the race begins. When you synchronize the race timer with the official race countdown timer, you are alerted at one-minute intervals as the race start approaches. When you combine the race timer with the virtual start line, the device measures your speed, bearing, and remaining time on the countdown timer. The device uses this data to indicate whether your boat will cross the start line before, after, or at the correct time to start the race.Starting Line GuidanceSailing start line guidance is a visual representation of the information you need to cross the start line at the optimal time and speed.After you set the starboard and port start line pins, and the target speed and time, and after you start the race timer, a predictor line appears. The predictor line extends from your current location toward the start line and the laylines that extend from each pin.The end point and color of the predictor line indicate where the boat will be when the timer expires, based on your current boat speed.When the end point is before the start line, the line is white. This indicates the boat must increase speed to reach the start line on time.When the end point is past the start line, the line is red. This indicates the boat must reduce speed to avoid a penalty for reaching the start line before the timer expires.When the end point is on the start line, the line is white. This indicates the boat is moving at an optimal speed to reach the start line when the timer expires.By default, the start line guidance window and the race timer window appear in the Sail Racing combination screen.Setting the Starting Line1From the starting line guidance gauge, select MENU > Start Line.2Select an option:• To mark the port and starboard starting line marks as you sail past them, select Ping Marks.• To mark the port and starboard starting line marks by entering their coordinates, select Enter Coordinates.• To switch the position of the port and starboard marks after you have set them, select Swap Port & Starbd. Marks.Using the Starting Line GuidanceYou can use the starting line guidance feature to help get you cross the start line, at the optimal speed during a sailing race.1Mark the starting line (Setting the Starting Line, page 26).2From the Start Line Guidance gauge, select MENU > Target Speed, and select your target speed when crossing the starting line.3Select Target Time, and select the target time to cross the starting line.4Select BACK.5Start the racing timer (Using the Race Timer, page 26).Using the Race Timer1From the starting line guidance gauge, select or to set the timer.2Select SELECT to start and stop the timer.Setting the Distance between the Bow and the GPS AntennaYou can enter the distance between the bow of your boat and the location of your GPS antenna. This helps ensure the bow of your boat crosses the starting line at the precise start time.1From the starting line guidance gauge, select MENU > Start Line > GPS Bow Offset.2Enter the distance.3Select SELECT.Laylines SettingsTo use the laylines features, you must connect a wind sensor to the chartplotter.When in sailing mode (Setting the Vessel Type, page 3), you can display laylines on the navigation chart. Laylines can be very helpful when racing.From the navigation chart, select MENU > Laylines.Display: Sets how the laylines and vessel appear on the chart, and sets the length of the laylines.Sailing Ang.: Allows you to select how the device calculates laylines. The Actual option calculates the laylines using the measured wind angle from the wind sensor. The Manual option calculates the laylines using manually entered windward and leeward angles.Windward Angle: Allows you to set a layline based on the windward sailing angle.Leeward Angle: Allows you to set a layline based on the leeward sailing angle.Tide Correction: Corrects the laylines based on the tide.Filter Time Constant: Filters the layline data based on the time interval entered. For a smoother layline that filters out some of the changes in the boat's heading or true wind angle, enter a higher number. For laylines that display a higher sensitivity to changes in the boat's heading or true wind angle, enter a lower number.Setting the Keel OffsetYou can enter a keel offset to compensate the water depth reading for the transducer installation location. This allows you to view the depth of the water below the keel or the true depth of the water, depending on your needs.26 Sailing Features
If you want to know the water depth below the keel or the lowest point of your boat and the transducer is installed at the water line or anywhere above the end of the keel, measure the distance from the transducer location to the keel of the boat.If you want to know the true water depth and the transducer is installed below the water line, measure the distance from the bottom of the transducer up to the water line.NOTE: This option is only available when you have valid depth data.1Measure the distance:• If the transducer is installed at the water line À or anywhere above the end of the keel, measure the distance from the transducer location to the keel of the boat. Enter this value as a positive number.• If the transducer is installed at the bottom of the keel Á and you want to know the true depth of the water, measure the distance from the transducer to the water line. Enter this value in as a negative number.2Select Settings > My Vessel > Keel Offset.3Select if the transducer is installed at the water line, or select if the transducer is installed at the bottom of the keel.4Enter the distance measured in step 1.5Use the arrow keys to enter the keel offset measured in step 1.Sailboat Autopilot Operation CAUTIONWhen engaged, the autopilot controls only the rudder. You and your crew remain responsible for the sails while the autopilot is engaged.In addition to heading hold, you can use the autopilot to maintain a wind hold. You can also use the autopilot to control the rudder while tacking and gybing.Wind HoldYou can set the autopilot to maintain a specific bearing relative to the current wind angle. Your device must be connected to a NMEA 2000 or NMEA® 0183 compatible wind sensor to perform a wind hold or a wind-based tack or gybe.Setting the Wind Hold TypeBefore you can enable the wind hold type, you must connect a NMEA 2000 or NMEA 0183 wind sensor to the autopilot.For advanced autopilot configuration, see the installation instructions included with your autopilot.1From the autopilot screen, select MENU > Autopilot Setup > Wind Hold Type.2Select Apparent or True.Engaging Wind HoldBefore you can enable the wind hold type, you must connect a NMEA 2000 or NMEA 0183 wind sensor to the autopilot.When the autopilot is in standby mode, select Wind Hold.Engaging Wind Hold from Heading HoldBefore you can enable the wind hold type, you must connect a NMEA 2000 or NMEA 0183 wind sensor to the autopilot.With heading hold engaged, select MENU > Wind Hold.Adjusting the Wind Hold Angle with the AutopilotYou can adjust the wind hold angle on the autopilot when wind hold is engaged.• To adjust the wind hold angle in increments of 1°, select or .• To adjust the wind hold angle in increments of 10°, hold or .Tack and GybeYou can set the autopilot to perform a tack or gybe while heading hold or wind hold is engaged.Tacking and Gybing from Heading Hold1Engage heading hold (Engaging the Autopilot, page 25).2Select MENU > Tack/Gybe.3Select a direction.The autopilot steers your boat through a tack or gybe.Tacking and Gybing from Wind HoldBefore you can engage wind hold, you must have a wind sensor installed.1Engage wind hold (Engaging Wind Hold, page 27).2Select MENU.3Select an option.The autopilot steers your boat through a tack or gybe, and information about the progress of the tack or gybe appears on the screen.Setting a Tack and Gybe DelayThe tack and gybe delay allows you to delay steering a tack and gybe after you initiate the maneuver.1From the autopilot screen, select MENU > Autopilot Setup > Sailing Setup > Tack/Gybe Delay.2Select the length of the delay.3If necessary, select Done.Enabling the Gybe InhibitorNOTE: The gybe inhibitor does not prevent you from manually performing a gybe using the helm or step steering.The gybe inhibitor prevents the autopilot from performing a gybe.1From the autopilot screen, select MENU > Autopilot Setup > Sailing Setup > Gybe Inhibitor.2Select Enabled.Gauges and GraphsThe gauges and graphs provide various information about the engine and environment. To view the information, a compatible transducer or sensor must be connected to the network.Viewing the CompassYou can view information about your bearing, heading, and route using the compass.Select Gauges > Compass.Gauges and Graphs 27
Viewing Trip GaugesTrip gauges show information for odometer, speed, time, and fuel for your present trip.Select Gauges > Trip.Resetting Trip Gauges1Select Gauges > Trip.2Select an option:• To set all the readings for the present trip to zero, select Reset Trip.• To set the maximum speed reading to zero, select Reset Maximum Speed.• To set the odometer reading to zero, select Reset Odometer.• To set all the readings to zero, select Reset All.Viewing Engine and Fuel GaugesBefore you can view engine and fuel gauges, you must be connected to a NMEA 2000 network capable of sensing engine and fuel data. See the installation instructions for details.Select Gauges > Engine.Selecting the Number of Engines Shown in GaugesYou can show information for up to four engines.1From the engine gauges screen, select MENU > Gauge Setup > Engine Selection > Num. Engines.2Select an option:• Select the number of engines.• Select Auto Configure to automatically detect the number of engines.Customizing the Engines Shown in GaugesBefore you can customize how the engines are shown in the gauges, you must manually select the number of engines (Selecting the Number of Engines Shown in Gauges, page 28).1From the engine gauges screen, select MENU > Gauge Setup > Engine Selection > Edit Engines.2Select First Engine.3Select the engine to display in the first gauge.4Repeat for the remaining engine bars.Enabling Status Alarms for Engine GaugesYou can enable the chartplotter to display engine status alarms.From the engine gauges screen, select MENU > Gauge Setup > Status Alarms > On.When an engine alarms is triggered, a gauge status alarm message appears and the gauge may become red depending on the type of alarm.Enabling Some Engine Gauge Status Alarms1From the engine gauges screen, select MENU > Gauge Setup > Status Alarms > Custom.2Select one or more engine gauge alarms to turn on or off.Setting the Fuel AlarmBefore you can set a fuel level alarm, a compatible fuel flow sensor must be connected to the chartplotter.You can set an alarm to sound when the total amount of remaining onboard fuel reaches the level you specify.1Select Settings > Alarms > Fuel > Set Total Fuel Onboard > On.2Enter the remaining amount of fuel that triggers the alarm, and select Done.Setting the Fuel Capacity of the Vessel1Select Settings > My Vessel > Fuel Capacity.2Enter the combined total capacity of the fuel tanks.Synchronizing the Fuel Data with the Actual Vessel FuelYou can synchronize the fuel levels in the chartplotter with the actual fuel in the vessel when you add fuel to your vessel.1Select Gauges > Engine > MENU.2Select an option:• After you have filled up all the fuel tanks on the vessel, select Fill Up All Tanks. The fuel level is reset to maximum capacity.• After you have added less than a full tank of fuel, select Add Fuel to Boat, and enter the amount added.• To specify the total fuel in the vessel tanks, select Set Total Fuel Onboard, and enter the total amount of fuel in the tanks.Viewing the Wind GaugesBefore you can view wind information, you must have a wind sensor connected to the chartplotter.Select Gauges > Wind.Configuring the Sailing Wind GaugeYou can configure the sailing wind gauge to show true or apparent wind speed and angle.1From the wind gauge, select MENU > Sailing Wind Gauge.2Select an option:• To show true or apparent wind angle, select Needle, and select an option.• To show true or apparent wind speed, select Wind Speed, and select an option.Configuring the Speed SourceYou can specify whether the vessel speed data displayed on the gauge and used for wind calculations is based on water speed or GPS speed.1From the wind gauge, select MENU > Compass Gauge > Speed Display.2Select an option:• To calculate the vessel speed based on data from the water-speed sensor, select Water Speed.• To calculate the vessel speed based on GPS data, select GPS Speed.Configuring the Heading Source of the Wind GaugeYou can specify the source of the heading displayed on the wind gauge. Magnetic heading is the heading data received from a heading sensor, and GPS heading is calculated by your chartplotter GPS (course over ground).1From the wind gauge, select MENU > Compass Gauge > Heading Source.2Select GPS Hdg or Magnetic.NOTE: When moving at low speeds or when stationary, the magnetic compass source is more accurate than the GPS source.Customizing the Close-Hauled Wind GaugeYou can specify the range of the close-hauled wind gauge for both the upwind scale and the downwind scale.1From the wind gauge, select MENU > Compass Gauge > Set Gauge Type > Close Hauled Gauge.28 Gauges and Graphs
2Select an option:• To set the maximum and minimum values that appear when the upwind close-hauled wind gauge appears, select Change Upwind Scale, and set the angles.• To set the maximum and minimum values that appear when the downwind close-hauled wind gauge appears, select Change Downwind Scale, and set the angles.• To view true or apparent wind, select Wind, and select an option.Tide, Current, and Celestial InformationTide Station InformationYou can view information about a tide station for a specific date and time, including the tide height, and when the next high and low tides will occur. By default, the chartplotter shows tide information for the most recently viewed tide station, present date, and past hour.Select Nav Info > Tides & Currents > Tides.Current Station InformationNOTE: Current station information is available with certain detailed maps.You can view information about a current station for a specific date and time, including the current speed and level of the current. By default, the chartplotter shows current information for the most recently viewed current station and for the present date and time.Select Nav Info > Tides & Currents > Currents.Celestial InformationYou can view information about sunrise, sunset, moonrise, moonset, moon phase, and the approximate sky view location of the sun and moon. The center of the screen represents the sky overhead, and the outermost rings represent the horizon. By default, the chartplotter shows celestial information for the present date and time.Select Nav Info > Tides & Currents > Celestial.Viewing Tide Station, Current Station, or Celestial Information for a Different Date1Select Nav Info > Tides & Currents.2Select Tides, Currents, or Celestial.3Select an option.• To view information for a different date, select Change Date > Manual, and enter a date.• To view information for today, select Change Date > Current.• If available, to view information for the day after the date shown, select Next Day.• If available, to view information for the day before the date shown, select Previous Day.Viewing Information for a Different Tide or Current Station1Select Nav Info > Tides & Currents.2Select Tides or Currents.3Select Nearby Stations.4Select a station.Digital Selective CallingChartplotter and NMEA 0183 VHF Radio FunctionalityWhen your chartplotter is connected to a NMEA 0183 VHF radio, these features are enabled.• The chartplotter can transfer your GPS position to your radio. If your radio is capable, GPS position information is transmitted with DSC calls.• The chartplotter can receive digital selective calling (DSC) distress and position information from the radio.• The chartplotter can track the positions of vessels sending position reports.Turning On DSCSelect Settings > Other Vessels > DSC.DSC ListThe DSC list is a log of the most recent DSC calls and other DSC contacts you have entered. The DSC list can contain up to 100 entries. The DSC list shows the most recent call from a boat. If a second call is received from the same boat, it replaces the first call in the call list.Viewing the DSC ListBefore you can view the DSC list, the chartplotter must be connected to a VHF radio that supports DSC.Select Nav Info > Other Vessels > DSC List.Adding a DSC ContactYou can add a vessel to your DSC list. You can make calls to a DSC contact from the chartplotter.1Select Nav Info > Other Vessels > DSC List > Add Contact.2Enter the Maritime Mobile Service Identity (MMSI) of the vessel.3Enter the name of the vessel.Incoming Distress CallsIf your compatible chartplotter and VHF radio are connected using NMEA 0183, your chartplotter alerts you when your VHF radio receives a DSC distress call. If position information was sent with the distress call, that information is also available and recorded with the call. designates a distress call in the DSC list and marks the position of the vessel on the Navigation chart at the time of the DSC distress call.Navigating to a Vessel in Distress designates a distress call in the DSC list and marks the position of a vessel on the Navigation chart at the time of the DSC distress call.1Select Nav Info > Other Vessels > DSC List.2Select a position-report call.3Select Navigate To.4Select Go To or Route To.Position TrackingWhen you connect the chartplotter to a VHF radio using NMEA 0183, you can track vessels that send position reports.This feature is also available with NMEA 2000, when the vessel sends the correct PGN data (PGN 129808; DSC Call Information).Every position report call received is logged in the DSC list (DSC List, page 29).Tide, Current, and Celestial Information 29
Viewing a Position Report1Select Nav Info > Other Vessels > DSC List.2Select a position-report call.3Select an option:• To switch to position report details, select .• To switch to a Navigation chart marking the location, select .• To switch to a Navigation chart marking the location, select Next Page.• To view the position report details, select Previous Page.Navigating to a Tracked Vessel1Select Nav Info > Other Vessels > DSC List.2Select a position-report call.3Select Navigate To.4Select Go To or Route To.Creating a Waypoint at the Position of a Tracked Vessel1Select Nav Info > Other Vessels > DSC List.2Select a position-report call.3Select Create Waypoint.Editing Information in a Position Report1Select Nav Info > Other Vessels > DSC List.2Select a position-report call.3Select Edit.• To enter the name of the vessel, select Name.• To select a new symbol, select Symbol, if available.• To enter a comment, select Comment.• To show a trail line for the vessel if your radio is tracking the position of the vessel, select Trail.• To select a color for the trail line, select Trail Line.Deleting a Position-Report Call1Select Nav Info > Other Vessels > DSC List.2Select a position-report call.3Select Edit > Clear Report.Viewing Vessel Trails on the ChartYou can view trails for all tracked vessels on some chart views. By default, a black line indicates the path of the vessel, a black dot indicates each previously reported position of a tracked vessel, and a blue flag indicates the last reported position of the vessel.1From a chart or 3D chart view, select MENU > Other Vessels > DSC Trails.2Select the number of hours to show tracked vessels on the chart.For example, if you select 4 Hours, all trail points that are less than four hours old appear for all tracked vessels.Individual Routine CallsWhen you connect the chartplotter to a Garmin VHF radio, you can use the chartplotter interface to set up an individual routine call.When setting up an individual routine call from your chartplotter, you can select the DSC channel on which you want to communicate. The radio transmits this request with your call.Selecting a DSC ChannelNOTE: The selection of a DSC channel is limited to those channels that are available in all frequency bands. The default channel is 72. If you select a different channel, the chartplotter uses that channel for subsequent calls until you call using another channel.1Select Nav Info > Other Vessels > DSC List.2Select a vessel or a station to call.3Select Call with Radio > Channel.4Select an available channel.Making an Individual Routine CallNOTE: When initiating a call from the chartplotter, if the radio does not have an MMSI number programmed, the radio will not receive call information.1Select Nav Info > Other Vessels > DSC List.2Select a vessel or a station to call.3Select Call with Radio.4If necessary, select Channel, and select a new channel.5Select Send.The chartplotter sends information about the call to the radio.6On your Garmin VHF radio, select Call.Making an Individual Routine Call to an AIS Target1From a chart or 3D chart view, select an AIS target.2Select AIS Vessel > Call with Radio.3If necessary, select Channel, and select a new channel.4Select Send.The chartplotter sends information about the call to the radio.5On your Garmin VHF radio, select Call.Media PlayerNOTE: The media player feature is not compatible with all chartplotter models.NOTE: Not all features are available on all connected media players.If you have a compatible stereo connected to the NMEA 2000 network, you can control the stereo using the chartplotter. The chartplotter should automatically detect the media player when it is first connected.You can play media from sources connected to the media player and sources connected to the NMEA 2000 network.Opening the Media PlayerBefore you can open the media player, you must connect a compatible device to the chartplotter.Select Media.IconsNOTE: Not all devices have these icons.Icon DescriptionSaves or deletes a channel as a presetRepeats all songsRepeats one song Scans for stations Searches for stations or skips songsShufflesSelecting the Media SourceWhen you have multiple media devices connected on a network, such as the NMEA 2000 network, you can select the media source you want to control from your chartplotter.30 Media Player
NOTE: You can play media only from sources that are connected to the device.NOTE: Not all features are available on all media sources.1From the media screen, select MENU > Source.NOTE: The source menu appears only for devices that support multiple media sources.2Select a source.Playing MusicBrowsing for Music1From the media screen, select Browse or MENU > Browse.2Select SELECT or select an option.Enabling Alphabetical SearchYou can enable the alphabetical search feature to find a song or album in a large list.From the media screen, select MENU > Installation > Alpha Search.Setting a Song to Repeat1While playing a song, select MENU > Repeat.2If necessary, select Single.Setting All Songs to RepeatFrom the media screen, select MENU > Repeat > All.Setting Songs to Shuffle1From the media screen, select MENU > Shuffle.2If necessary, select an option.Adjusting the VolumeEnabling and Disabling ZonesIf you have wired your vessel's speakers into zones, you can enable needed zones and disable unused zones.1From the media screen, select MENU > Audio Levels > Enable/Disable Zones.2Select a zone.Muting the Media Volume1From the media screen, select .2If necessary, select SELECT.VHF RadioScanning VHF ChannelsBefore you can scan VHF channels, you must set the source to VHF.You can monitor VHF channels saved as presets for activity and automatically switch to an active channel.From the VHF media screen, select MENU > Scan.Adjusting the VHF SquelchNOTE: Your media player must support VHF radio to use this feature.1From the VHF source page, select MENU > Squelch.2Use the slider bar to adjust the VHF squelch.RadioTo listen to AM or FM radio, you must have a suitable marine AM/FM antenna properly connected to the stereo and be within range of a broadcasting station. For instructions on connecting an AM/FM antenna, see the stereo installation instructions.To listen to SiriusXM® radio, you must have the appropriate equipment and subscriptions (SiriusXM Satellite Radio, page 32). For instructions on connecting a SiriusXM Connect Vehicle Tuner, see the stereo installation instructions.To listen to DAB stations, you must have the appropriate equipment (DAB Playback, page 31). For instructions on connecting a DAB adapter and antenna, see the installation instructions provided with your adapter and antenna.Setting the Tuner Region1From the media screen, select MENU > Installation > Tuner Region.2Select an option.Changing the Radio Station1From the media screen, select an applicable source, such as FM.2Select or to tune to a station.Changing the Tuning ModeYou can change how you select a station for some media types, such as FM or AM radio.NOTE: Not all tuning modes are available for all media sources.1From the media screen, select MENU > Tuning Mode.2Select an option.3If necessary, select SELECT.PresetsYou can save your favorite AM stations and FM stations as presets for easy access.You can save your favorite SiriusXM channels if you are connected to an optional SiriusXM tuner and antenna.Saving a Station as a Preset1From an applicable media screen, tune to the station to save as a preset.2Select Presets > Add Current Channel.Selecting a Preset1From an applicable media screen, select Presets.2Select a preset from the list.3Select Tune to Channel.Removing a Preset1From an applicable media screen, select Presets.2Select a preset from the list.3Select Remove Current Channel.DAB PlaybackWhen you connect a compatible Digital Audio Broadcasting (DAB) module and antenna, such as the FUSION® MS-DAB100A to a compatible stereo, you can tune in to and play DAB stationsTo use the DAB source, you must be in a region in which DAB is available, and select the tuner region (Setting the DAB Tuner Region, page 31).Setting the DAB Tuner RegionYou must select the region you are in to receive DAB stations properly.1From the media screen, select MENU > Installation > Tuner Region.2Select the region you are in.Scanning for DAB StationsBefore you can scan for DAB stations, you must connect a compatible DAB module and antenna (not included) to the stereo. Because DAB signals are broadcast in select countries only, you must also set the tuner region to a location where DAB signals are broadcast.Media Player 31
1Select the DAB source.2Select Scan to scan for available DAB stations.When scanning is complete, the first available station in the first ensemble found begins playing.NOTE: After the first scan is complete, you can select Scan again to re-scan for DAB stations. When the re-scan is complete, the system starts playing the first station in the ensemble you were listening to when you started the re-scan.Changing DAB Stations1Select the DAB source.2If necessary, select Scan to scan for local DAB stations.3Select or to change the station.When you reach the end of the current ensemble, the stereo automatically changes to the first available station in the next ensemble.Selecting a DAB Station from a List1From the DAB media screen, select Browse > Stations.2Select a station from the list.Selecting a DAB Station from a Category1From the DAB media screen, select Browse > Categories.2Select a category from the list.3Select a station from the list.DAB PresetsYou can save your favorite DAB stations as presets for easy access.You can save up to 15 DAB-station presets.Saving a DAB Station as a Preset1From the DAB media screen, select the station to save as a preset.2Select Browse > Presets > Save Current.Selecting a DAB Preset from a List1From the DAB media screen, select Browse > Presets > View Presets.2Select a preset from the list.Removing DAB Presets1From the DAB media screen, select Browse > Presets.2Select an option:• To remove one preset, select Remove Preset, and select the preset.• To remove all presets, select Remove All Presets.SiriusXM Satellite RadioWhen you have a FUSION-Link™ capable stereo and SiriusXM Connect Tuner installed and connected to the chartplotter, you may have access to SiriusXM satellite radio, depending on your subscription.Locating a SiriusXM Radio IDBefore you can activate your SiriusXM subscription, you must have the radio ID of your SiriusXM Connect Tuner.You can locate the SiriusXM Radio ID on the back of the SiriusXM Connect Tuner, on the back of its packaging, or by tuning your chartplotter to channel 0.1Select Media > Source > SiriusXM.2Tune to channel 0.The SiriusXM radio ID does not include the letters I, O, S, or F.Activating a SiriusXM Subscription1With the SiriusXM source selected, tune to channel 1.You should be able to hear the preview channel. If not, check the SiriusXM Connect Tuner and antenna installation and connections, and try again.2Tune to channel 0 to locate the Radio ID.3Contact SiriusXM listener care by phone at (866) 635-2349 or go to www.siriusxm.com/activatenow to subscribe in the United States.4Provide the Radio ID.The activation process usually takes 10 to 15 minutes, but can take up to an hour. For the SiriusXM Connect Tuner to receive the activation message, it must be turned on and receiving the SiriusXM signal.5If the service is not activated within the hour, go to http://care.siriusxm.com/refresh or contact SiriusXM by phone at 1-855-MYREFRESH (697-3373).Customizing the Channel GuideSiriusXM radio channels are grouped in categories. You can select the categories of channels that appear in the channel guide.Select an option:• If the media device is a FUSION-Link capable stereo, select Media > Browse > Channel.• If the media device is a GXM™ antenna, select Media > MENU > Category.Saving a SiriusXM Channel to the Presets ListYou can save your favorite channels to the presets list.1Select Media.2Select the channel to save as a preset.3Select an option:• If the media device is a FUSION-Link capable stereo, select Browse > Presets.• If the media device is a GXM antenna, select MENU > Presets > Add Current Channel.Unlocking SiriusXM Parental Controls1From the media screen, select Browse > Parental > Unlock.2Enter your passcode.The default passcode is 0000.Setting Parental Controls on SiriusXM Radio ChannelsBefore you can set parental controls, the parental controls must be unlocked.The parental control feature allows you to limit access to any SiriusXM channels, including those with mature content. When enabled, the parental control feature requires you to enter a passcode to tune to the locked channels.Select Browse > Parental > Lock/Unlock.A list of channels appears. A checkmark indicates a locked channel.NOTE: When you view the channels after setting parental controls, the display changes:• indicates a locked channel.• indicates an unlocked channel.Changing a Parental Passcode on a SiriusXM RadioBefore you can change the passcode, the parental controls must be unlocked.1From the media screen, select Browse > Parental > Change PIN.2Enter your passcode and select Done.3Enter a new passcode.4Confirm the new passcode.32 Media Player
Restoring Default Parental Control Settings ValuesThis process deletes all the settings information you have entered. When you restore the parental control settings to their default values, the passcode value is reset to 0000.1From the media menu, select Installation > Factory Defaults.2Select Yes.Clearing All Locked Channels on a SiriusXM RadioBefore you can clear all locked channels, the parental controls must be unlocked.1From the media screen, select Browse > Parental > Clear All Locked.2Enter your passcode.Setting the Device Name1From the media screen, select MENU > Installation > Set Device Name.2Enter a device name.3Select SELECT or Done.Updating the Media Player SoftwareYou can update the software on compatible connected stereos and accessories.1Go to www.fusionentertainment.com/marine, and download the software update onto a USB flash drive.Software updates and instructions are available on your device product page.2Insert the USB flash drive into the USB port of the stereo.3On the chartplotter media screen, select MENU > Installation > Update Software.4Select the item to update.Device ConfigurationTurning On the Chartplotter AutomaticallyYou can set the chartplotter to turn on automatically when the power is applied. Otherwise, you must turn on the chartplotter by pressing .Select Settings > System > Auto Power.NOTE: When Auto Power is On, and the chartplotter is turned off using , and power is removed and reapplied within less than two minutes, you may need to press to restart the chartplotter.System SettingsSelect Settings > System.Display: Adjusts the backlight brightness and color scheme.Beeper: Turns on and off the tone that sounds for alarms and selections.GPS: Provides information about the GPS satellite settings and fix.Auto Power: Turns on the device automatically when power is applied (Turning On the Chartplotter Automatically, page 33 ).Keyboard Layout: Sets the arrangement of the keyboard to an alphabetical or computer keyboard layout.Language: Sets the on-screen text language.Speed Sources: Sets the source of the speed data used to calculate true wind speed or fuel economy. Water speed is the speed reading from a water-speed sensor, and GPS speed is calculated from your GPS position.System Information: Provides information about the device and the software version.Simulator: Turns on the simulator and allows you to set the speed and simulated location.Display SettingsNot all options are available on all models.Select Settings > System > Display.Backlight: Sets the backlight level.Color Mode: Sets the device to display day or night colors.Screenshot Capture: Allows the device to save images of the screen.Menu Bar Display: Shows or automatically hides the menu bar when it is not needed.GPS SettingsSelect Settings > System > GPS.Skyview: Shows the relative position of GPS satellites in the sky.WAAS/EGNOS: Turns on or off WAAS (in North America) or EGNOS (in Europe), which can provide more-accurate GPS position information. When using WAAS or EGNOS, the device may take longer to acquire satellites.Speed Filter: Averages the speed of your vessel over a short period of time for smoother speed values.Source: Allows you to select the preferred source for GPS.Viewing the Event LogThe event log shows a list of system events.Select Settings > System > System Information > Event Log.Viewing System Software InformationYou can view the software version, the basemap version, all supplemental map information (if applicable), the software version for an optional Garmin radar (if applicable), and the unit ID number. You may need this information to update the system software or to purchase additional map data information.You can view the software version, the basemap version, all supplemental map information (if applicable), and the unit ID number. You may need this information to update the system software or to purchase additional map data information.Select Settings > System > System Information > Software Information.My Vessel SettingsNOTE: Some settings and options require additional charts or hardware.Select Settings > My Vessel.Keel Offset: Offsets the surface reading for the depth of a keel, making it possible to measure depth from the bottom of the keel instead of from the transducer location (Setting the Keel Offset, page 26).Calibrate Water Speed: Calibrates the speed-sensing transducer or sensor (Calibrating a Water Speed Device, page 34).Fuel Capacity: Sets the combined fuel capacity of all the fuel tanks on your vessel (Setting the Fuel Capacity of the Vessel, page 28).Vessel Type: Enables some chartplotter features based on the boat type.Fill Up All Tanks: Sets the tank levels to full (Synchronizing the Fuel Data with the Actual Vessel Fuel, page 28).Add Fuel to Boat: Allows you to enter the quantity of fuel you added to your tank, when you did not entirely fill up the tank Device Configuration 33
(Synchronizing the Fuel Data with the Actual Vessel Fuel, page 28).Set Total Fuel Onboard: Sets the combined amount of fuel in all the fuel tanks on your vesselSynchronizing the Fuel Data with the Actual Vessel Fuel, page 28.Set Gauge Limits: Sets the upper and lower limits of various gauges (Customizing Engine Gauge and Fuel Gauge Limits, page 34).Setting the Keel OffsetYou can enter a keel offset to compensate the water depth reading for the transducer installation location. This allows you to view the depth of the water below the keel or the true depth of the water, depending on your needs.If you want to know the water depth below the keel or the lowest point of your boat and the transducer is installed at the water line or anywhere above the end of the keel, measure the distance from the transducer location to the keel of the boat.If you want to know the true water depth and the transducer is installed below the water line, measure the distance from the bottom of the transducer up to the water line.NOTE: This option is only available when you have valid depth data.1Measure the distance:• If the transducer is installed at the water line À or anywhere above the end of the keel, measure the distance from the transducer location to the keel of the boat. Enter this value as a positive number.• If the transducer is installed at the bottom of the keel Á and you want to know the true depth of the water, measure the distance from the transducer to the water line. Enter this value in as a negative number.2Select Settings > My Vessel > Keel Offset.3Select if the transducer is installed at the water line, or select if the transducer is installed at the bottom of the keel.4Enter the distance measured in step 1.5Use the arrow keys to enter the keel offset measured in step 1.Setting the Water Temperature OffsetBefore you can set the water temperature offset, you must have a NMEA 0183 water-temperature sensor or a temperature-capable transducer to measure water temperature.The temperature offset compensates for the temperature reading from a temperature sensor.1Measure the water temperature using the temperature sensor or temperature-capable transducer that is connected to the chartplotter.2Measure the water temperature using a different temperature sensor or a thermometer that is known to be accurate.3Subtract the water temperature measured in step 1 from the water temperature measured in step 2.This is the temperature offset. Enter this value in step 5 as a positive number if the sensor connected to the chartplotter measures the water temperature as being colder than it actually is. Enter this value in step 5 as a negative number if the sensor connected to the chartplotter measures the water temperature as being warmer than it actually is.4Select Settings > My Vessel > Temp. Offset.5Enter the temperature offset calculated in step 3.Calibrating a Water Speed DeviceIf you have a speed-sensing transducer connected to the chartplotter, you can calibrate that speed-sensing device to improve the accuracy of water-speed data displayed by the chartplotter.1Select Settings > My Vessel > Calibrate Water Speed.2Follow the on-screen instructions.If the boat is not moving fast enough or the speed sensor is not registering a speed, a message appears.3Select OK, and safely increase the boat speed.4If the message appears again, stop the boat, and ensure the speed-sensor wheel is not stuck.5If the wheel turns freely, check the cable connections.6If you continue to get the message, contact Garmin product support.Setting the Fuel Capacity of the Vessel1Select Settings > My Vessel > Fuel Capacity.2Enter the combined total capacity of the fuel tanks.Synchronizing the Fuel Data with the Actual Vessel FuelYou can synchronize the fuel levels in the chartplotter with the actual fuel in the vessel when you add fuel to your vessel.1Select Gauges > Engine > MENU.2Select an option:• After you have filled up all the fuel tanks on the vessel, select Fill Up All Tanks. The fuel level is reset to maximum capacity.• After you have added less than a full tank of fuel, select Add Fuel to Boat, and enter the amount added.• To specify the total fuel in the vessel tanks, select Set Total Fuel Onboard, and enter the total amount of fuel in the tanks.Customizing Engine Gauge and Fuel Gauge LimitsYou can configure the upper and lower limits and the range of desired standard operation of a gauge. When a value exceeds the range of standard operation, the gauge becomes red.NOTE: Not all options are available for all gauges.1Select a gauge.2Select Gauge Limits > Custom > Edit Limits.3Select an option:• To set the minimum value of the standard operating range, select Rated Min..• To set the maximum value of the standard operating range, select Rated Max..• To set the lower limit of the gauge lower than the rated minimum, select Scale Min..34 Device Configuration
• To set the upper limit of the gauge higher than the rated maximum, select Scale Max..4Select the limit value.5Repeat steps 4 and 5 to set additional gauge limits.Communications SettingsNOTE: Some settings and options require additional charts or hardware.Select Settings > Communications.Serial Port: Sets the input/output format for the serial port to use when connecting the chartplotter to external NMEA devices, computers, or other Garmin devices.NMEA 0183 Setup: Sets the NMEA 0183 sentences the chartplotter transmits, how many digits to the right of the decimal point are transmitted in a NMEA output, and how waypoints are identified (NMEA 0183 Settings, page 35).NMEA 2000 Setup: Allows you to view and label the devices on the NMEA 2000 network (NMEA 2000 Settings, page 35).Marine Network: Allows you to view the devices with which you are sharing maps, sonar, or radar. Not available on all chartplotter models.NOTE: You can only view networked data on a model that supports that data. For example, you cannot view networked radar on model that does not support radar.Wi-Fi Network: Allows you set up the Wi‑Fi network (Setting Up the Wi‑Fi Wireless Network, page 35).NMEA 0183The chartplotters support the NMEA 0183 standard, which is used to connect various NMEA 0183 devices, such as VHF radios, NMEA instruments, autopilots, wind sensors, and heading sensors.To connect the chartplotter to optional NMEA 0183 devices, see the chartplotter installation instructions.The approved NMEA 0183 sentences for the chartplotter are GPAPB, GPBOD, GPBWC, GPGGA, GPGLL, GPGSA, GPGSV, GPRMB, GPRMC, GPRTE, GPVTG, GPWPL, GPXTE, and Garmin proprietary sentences PGRME, PGRMM, and PGRMZ.This chartplotter also includes support for the WPL sentence, DSC, and sonar NMEA 0183 input with support for the DPT (depth) or DBT, MTW (water temperature), and VHW (water temperature, speed, and heading) sentences.NMEA 0183 SettingsSelect Settings > Communications > NMEA 0183 Setup.Sounder: Enables NMEA 0183 output sentences for the sounder (if applicable).Route: Enables NMEA 0183 output sentences for routes.System: Enables NMEA 0183 output sentences for system information.Garmin: Enables NMEA 0183 output sentences for Garmin proprietary sentences.Posn Precision: Adjusts the number of digits to the right of the decimal point for transmission of NMEA output.Waypoint IDs: Sets the device to transmit waypoint names or numbers via NMEA 0183 while navigating. Using numbers may resolve compatibility issues with older NMEA 0183 autopilots.Diagnostics: Displays NMEA 0183 diagnostic information.Defaults: Restores the NMEA 0183 settings to the original factory defaults.NMEA 2000 SettingsSelect Settings > Communications > NMEA 2000 Setup.Device List: Displays the devices connected to the network.Label Devices: Changes the labels for available connected devices.Naming Devices and Sensors on the NetworkYou can name devices and sensors connected to the Garmin Marine Network and the NMEA 2000 network.1Select Settings > Communications.2Select Marine Network or NMEA 2000 Setup > Device List.3Select a device from the list on the left.4Select Change Name.5Enter the name, and select Done.Wi‑Fi NetworkSetting Up the Wi‑Fi Wireless NetworkThe chartplotters can create a Wi‑Fi network to which you can connect wireless devices. The first time you access the wireless network settings, you are prompted to set up the network.1Select Settings > Communications > Wi-Fi Network > Wi-Fi > On > OK.2If necessary, enter a name for this wireless network.3Enter a password.You will need this password to access the wireless network from a wireless device. The password is case-sensitive.Connecting a Wireless Device to the ChartplotterBefore you can connect a wireless device to the chartplotter wireless network, you must configure the chartplotter wireless network (Setting Up the Wi‑Fi Wireless Network, page 35).You can connect multiple wireless devices to the chartplotter to share data.1From the wireless device, turn on the Wi‑Fi technology and search for wireless networks.2Select the name of your chartplotter wireless network (Setting Up the Wi‑Fi Wireless Network, page 35).3Enter the network password.Changing the Wireless ChannelYou can change the wireless channel if you have trouble finding or connecting to a device, or if you experience interference.1Select Settings > Communications > Wi-Fi Network > Advanced > Channel.2Enter a new channel.You do not need to change the wireless channel of devices connected to this network.Setting AlarmsNavigation AlarmsSelect Settings > Alarms > Navigation.Arrival: Sets an alarm to sound when you are within a specified distance or time from a turn or a destination.Anchor Drag: Sets an alarm to sound when you exceed a specified drift distance while anchored.Off Course: Sets an alarm to sound when you are off course by a specified distance.System AlarmsAlarm Clock: Sets an alarm clock.Device Voltage: Sets an alarm to sound when the battery reaches a specified low voltage.GPS Accuracy: Sets an alarm to sound when the GPS location accuracy falls outside the user-defined value.Setting the Fuel AlarmBefore you can set a fuel level alarm, a compatible fuel flow sensor must be connected to the chartplotter.Device Configuration 35
You can set an alarm to sound when the total amount of remaining onboard fuel reaches the level you specify.1Select Settings > Alarms > Fuel > Set Total Fuel Onboard > On.2Enter the remaining amount of fuel that triggers the alarm, and select Done.Units SettingsSelect Settings > Units.System Units: Sets the unit format for the device.Variance: Sets the magnetic declination, the angle between magnetic north and true north, for your present location.North Reference: Sets the direction references used in calculating heading information. True sets geographic north as the north reference. Grid sets grid north as the north reference (000º). Magnetic sets the magnetic north as the north reference.Position Format: Sets the position format in which a given location reading appears. Do not change this setting unless you are using a map or chart that specifies a different position format.Map Datum: Sets the coordinate system on which the map is structured. Do not change this setting unless you are using a map or chart that specifies a different map datum.Pressure Reference Time: Sets the reference time used to calculate the barometer trend. The trend is indicated in the barometer field.Time Format: Sets a 12-hour, 24-hour, or UTC time format.Time Zone: Sets the time zone, or allows automatic selection based on GPS location.Navigation SettingsNOTE: Some settings and options require additional charts or hardware.Select Settings > Navigation.Route Labels: Sets the type of labels shown with route turns on the map.Auto Guidance: Sets the parameters the chartplotter uses when calculating an Auto Guidance path, when you are using some premium maps.Turn Transition Activ.: Sets the turn transition to be calculated based on time or distance.Turn Transition Time: Sets how many minutes before the turn that you transition to it as the next leg, when Time is selected for the Turn Transition Activ. setting. You can raise this value to help improve the accuracy of the autopilot when navigating a route or an Auto Guidance path with many frequent turns or at higher speeds. For straighter routes or slower speeds, lowering this value can improve autopilot accuracy.Turn Transition Dist.: Sets how far before the turn that you transition to it as the next leg, when Distance is selected for the Turn Transition Activ. setting. You can raise this value to help improve the accuracy of the autopilot when navigating a route or an Auto Guidance path with many frequent turns or at higher speeds. For straighter routes or slower speeds, lowering this value can improve autopilot accuracy.Route Start: Selects a starting point for route navigation.Other Vessel SettingsWhen your compatible chartplotter is connected to an AIS device or VHF radio, you can set up how other vessels are displayed on the chartplotter.Select Settings > Other Vessels.AIS: Enables and disables AIS signal reception.DSC: Enables and disables digital selective calling (DSC).AIS Alarm: Sets the collision alarm (Setting the Safe-Zone Collision Alarm, page 8 and Enabling AIS Transmission Test Alerts, page 8).Restoring the Original Chartplotter Factory SettingsNOTE: This procedure deletes all settings information you have entered.Select Settings > System > System Information > Factory Settings.Sharing and Managing User DataYou can share and manage user data using a memory card. You must have a memory card installed in the device. This device supports up to a 32 GB memory card, formatted to FAT32.You can share data if two compatible devices are connected using the blue and brown wires on the power cable or using the User Data Sharing Cable (Connecting to a Garmin Device to Share User Data, page 36).Connecting to a Garmin Device to Share User DataNOTE: This feature is not available on ECHOMAP Plus 70/90 devices. The blue and brown wires on those devices can connect to NMEA 0183 devices only.You can connect the ECHOMAP Plus 40/60 device to a compatible Garmin device to share user data, such as waypoints. If the devices are mounted near each other, you can connect the blue and brown wires. If the devices are mounted too far apart for the wires to reach, you can connect the devices using a User Data Sharing Cable (010-12234-06).1Make sure both devices are connected to the same ground.2Complete an action:• If the devices are mounted near each other, connect the blue wire from the first device to the brown wire of the second, and connect the brown wire from the first device to the blue wire of the second.• If the devices are not mounted near each other, obtain a User Data Sharing Cable (010-12234-06), and connect the devices following the instructions included with the cable (User Data Sharing Cable Wiring Diagram, page 36).3On both devices, select Nav Info > Manage Data > User Data Sharing.User data is shared between the connected devices. If you select Clear User Data, data is removed from both connected devices.User Data Sharing Cable Wiring DiagramItem Wire Function Wire ColorÀData BlueÁData BrownÂGround Black36 Sharing and Managing User Data
Item Wire Function Wire ColorÃData GreenÄData WhiteSelecting a File Type for Third-Party Waypoints and RoutesYou can import and export waypoints and routes from third-party devices.1Insert a memory card into the card slot.2Select Nav Info > Nav Info > Data Transfer > File Type.3Select GPX.To transfer data with Garmin devices again, select the ADM file type.Copying User Data from a Memory CardYou can transfer user data from a memory card to transfer from other devices. User data includes waypoints, routes, Auto Guidance paths, tracks, and boundaries. NOTE: Only boundary files with an .adm extension are supported.1Insert a memory card into a card slot.2Select Nav Info > Manage Data > Data Transfer.3If necessary, select the memory card to copy data to.4Select an option:• To transfer data from the memory card to the chartplotter and combine it with existing user data, select Merge from Card.• To transfer data from the memory card to the chartplotter and overwrite existing user data, select Replace from Card.5Select the file name.Copying User Data to a Memory CardYou can save user data to a memory card to transfer to other devices. User data includes waypoints, routes, Auto Guidance paths, tracks, and boundaries. 1Insert a memory card into the card slot.2Select Nav Info > Manage Data > Data Transfer > Save to Card.3If necessary, select the memory card to copy the data to.4Select an option:• To create a new file, select Add New File, and enter a name.• To add the information to an existing file, select the file from the list, and select Save to Card.Copying Built-In Maps to a Memory CardYou can copy maps from the chartplotter to a memory card for use with HomePort.1Insert a memory card into the card slot.2Select Nav Info > Manage Data > Data Transfer.3Select Copy Built-In Map.Copying Waypoints, Routes, and Tracks from HomePort to a ChartplotterBefore you can copy data to the chartplotter, you must have the latest version of the HomePort software program loaded on your computer and a memory card installed in the chartplotter.Copy the data from HomePort to the prepared memory card.For more information, see the HomePort help file.Backing Up Data to a Computer1Insert a memory card into the card slot.2Select Nav Info > Manage Data > Data Transfer > Save to Card.3Select a file name from the list, or select Add New File.4Select Save to Card.5Remove the memory card, and insert it into a card reader attached to a computer.6Open the Garmin\UserData folder on the memory card.7Copy the backup file on the card and paste it to any location on the computer.Restoring Backup Data to a Chartplotter1Insert a memory card into a card reader that is attached to the computer.2Copy a backup file from the computer to the memory card, into a folder named Garmin\UserData.3Insert a memory card into the card slot.4Select Nav Info > Manage Data > Data Transfer > Replace from Card.Saving System Information to a Memory CardYou can save system information to a memory card as a troubleshooting tool. A product support representative may ask you to use this information to retrieve data about the network.1Insert a memory card into the card slot.2Select Settings > System > System Information > Garmin Devices > Save to Card.3If necessary, select the memory card to save system information to.4Remove the memory card.Clearing Saved DataYou can remove saved user data from the device memory. User data includes waypoints, routes, Auto Guidance paths, tracks, and boundaries. 1Select Nav Info > Manage Data > Clear User Data.2Select an option.NOTICEIf you select All, all the data you have saved will be removed, except Garmin Quickdraw contours data.If you are connected to another device and User Data Sharing is enabled, data is removed from all connected devices.AppendixCleaning the ScreenNOTICECleaners containing ammonia will harm the anti-reflective coating.The device is coated with a special anti-reflective coating which is very sensitive to waxes and abrasive cleaners.1Apply an eyeglass lens cleaner specified as safe for anti-reflective coatings to the cloth.2Gently wipe the screen with a soft, clean, lint-free cloth.Appendix 37
ScreenshotsYou can capture a screenshot of any screen shown on your chartplotter as a bitmap (.bmp) file. You can transfer the screenshot to your computer.Capturing Screenshots1Insert a memory card into the card slot.2Select Settings > System > Display > Screenshot Capture > On.3Go to a screen you want to capture.4Hold HOME for at least six seconds.Copying Screenshots to a Computer1Remove the memory card from the chartplotter, and insert it into a card reader that is attached to a computer.2From Windows® Explorer, open the Garmin\scrn folder on the memory card.3Copy a .bmp file from the card and paste it to any location on the computer.TroubleshootingMy device will not acquire GPS signalsIf the device is not acquiring satellite signals, there could be a few causes. If the device has moved a large distance since the last time it has acquired satellites or has been turned off for longer than a few weeks or months, the device may not be able to acquire the satellites correctly.• Ensure the device is using the latest software. If not, update the device software (Updating the Device Software, page 40).• Make sure the device has a clear view of the sky so the antenna can receive the GPS signal. If it is mounted inside of a cabin, it should be close to a window so it can receive the GPS signal.My device will not turn on or keeps turning offDevices erratically turning off or not turning on could indicate an issue with the power supplied to the device. Check these items to attempt to troubleshoot the cause of the power issue.• Make sure the power source is generating power.You can check this several ways. For example, you can check whether other devices powered by the source are functioning.• Check the fuse in the power cable.The fuse should be located in a holder that is part of the red wire of the power cable. Check that the proper size fuse is installed. Refer to the label on the cable or the installation instructions for the exact fuse size needed. Check the fuse to make sure there is still a connection inside of the fuse. You can test the fuse using a multimeter. If the fuse is good, the multimeter reads 0 ohm.• Check to make sure the device is receiving is at least 10 V, but 12 V is recommended.To check the voltage, measure the female power and ground sockets of the power cable for DC voltage. If the voltage is less than 10 V, the device will not turn on.• Make sure the device is firmly secured in the cradle. If the model uses a locking bracket, make sure the bracket is firmly snapped close. There is an audible click when the device or locking bracket is installed correctly. If the device is not firmly secured, it can lose power. The device can also fall out of the cradle and become damaged if it is not firmly secured.• If the device is receiving enough power but does not turn on, contact Garmin product support at support.garmin.com.Changing the Fuse in the Power Cable1Open the fuse housing À.2Twist and pull the fuse to remove it Á.3Insert a new 3 A fast-blow fuse.4Close the fuse housing.My sonar does not work• Push the transducer cable all the way into the back of the device.Even if the cable seems to be connected, you should push firmly so that it is fully seated.• Press , and ensure sonar is enabled.• Select the correct transducer type (Selecting the Transducer Type, page 20).My device is not creating waypoints in the correct locationYou can manually enter a waypoint location to transfer and share data from one device to the next. If you have manually entered a waypoint using coordinates, and the location of the point does not appear where the point should be, the map datum and position format of the device may not match the map datum and position format originally used to mark the waypoint.Position format is the way in which the GPS receiver's position appears on the screen. This is commonly displayed as latitude/longitude in degrees and minutes, with options for degrees, minutes and second, degrees only, or one of several grid formats.Map datum is a math model which depicts a part of the surface of the earth. Latitude and longitude lines on a paper map are referenced to a specific map datum.1Find out which map datum and position format was used when the original waypoint was created.If the original waypoint was taken from a map, there should be a legend on the map that lists the map datum and position format used to create that map. Most often this is found near the map key.2Select Settings > Units.3Select the correct map datum and position format settings.4Create the waypoint again.My device does not display the correct timeTime is set by GPS position and time zone setting.1Select Settings > Units > Time Zone.2Ensure the device has a GPS fix.NMEA 2000 PGN InformationType PGN DescriptionTransmit and receive 059392 ISO acknowledgment059904 ISO request060928 ISO address claim126208 NMEA: Command, request, and acknowledge group function126996 Product information127250 Vessel heading128259 Speed: Water referenced128267 Water depth129539 GNSS DOPs129799 Radio frequency, mode, and power130306 Wind data38 Appendix
Type PGN Description130312 TemperatureTransmit 126464 Transmit and receive PGN list group function127258 Magnetic Variance129025 Position: Rapid update129026 COG and SOG: Rapid update129029 GNSS position data129283 Cross track error129284 Navigation data129285 Navigation route and waypoint info129540 GNSS satellites in viewReceive 127245 Rudder127250 Vessel heading127488 Engine parameters: Rapid update127489 Engine parameters: Dynamic127493 Transmission parameters: Dynamic127498 Engine parameters: Static127505 Fluid level129038 AIS class A position report129039 AIS class B position report129040 AIS class B extended position report129794 AIS class A static and voyage related data129798 AIS SAR aircraft position report129802 AIS safety-related broadcast message129808 DSC call information130310 Environmental parameters130311 Environmental parameters (obsolete)130313 Humidity130314 Actual pressure130576 Small craft statusThis data applies only to NMEA 2000-compatible products.NMEA 0183 InformationType Sentence DescriptionTransmit GPAPB APB: Heading or track controller (autopilot) sentence "B"GPBOD BOD: Bearing (origin to destination)GPBWC BWC: Bearing and distance to waypointGPGGA GGA: Global positioning system fix dataGPGLL GLL: Geographic position (latitude and longitude)GPGSA GSA: GNSS DOP and active satellitesGPGSV GSV: GNSS satellites in viewGPRMB RMB: Recommended minimum navigation informationGPRMC RMC: Recommended minimum specific GNSS dataGPRTE RTE: RoutesGPVTG VTG: Course over ground and ground speedGPWPL WPL: Waypoint locationGPXTE XTE: Cross track errorPGRME E: Estimated errorPGRMM M: Map datumPGRMZ Z: AltitudeSDDBT DBT: Depth below transducerSDDPT DPT: DepthType Sentence DescriptionSDMTW MTW: Water temperatureSDVHW VHW: Water speed and headingReceive DPT DepthDBT Depth below transducerMTW Water temperatureVHW Water speed and headingWPL Waypoint locationDSC Digital selective calling informationDSE Expanded digital selective callingHDG Heading, deviation, and variationHDM Heading, magneticMWD Wind direction and speedMDA Meteorological compositeMWV Wind speed and angleVDM AIS VHF data-link messageYou can purchase complete information about National Marine Electronics Association (NMEA) format and sentences from: NMEA, Seven Riggs Avenue, Severna Park, MD 21146 USA (www.nmea.org)Registering Your DeviceNOTE: If your device has Wi‑Fi technology, you should use the ActiveCaptain app to register the device (Getting Started with the ActiveCaptain App, page 3).Help us better support you by completing our online registration today. Keep the original sales receipt, or a photocopy, in a safe place.1Insert a memory card into the card slot on the chartplotter.2Wait a few moments.The chartplotter opens the card management page and creates a file named GarminDevice.xml in the Garmin folder on the memory card.3Remove the memory card.4Insert the memory card into your computer.5On your computer, go to garmin.com/express.6Follow the on-screen instructions to download, install, and open the Garmin Express™ application.7Select > Add a Device.8While the application searches, select Sign In next to Have marine charts or devices? near the bottom of the screen.9Create or sign in to your Garmin account.10Follow the on-screen instructions to set up your vessel.11Select > Add.The Garmin Express application searches the memory card for the device information.12Select Add Device to register the device.When registration is complete, the Garmin Express application searches for additional charts and chart updates for your device.When you add devices to the chartplotter network, repeat these steps to register the new devices.Software UpdateNOTE: If your device has Wi‑Fi technology, you should use the ActiveCaptain app to update the device software (Updating Software with the ActiveCaptain App, page 4).You may need to update the device software when you install the device or add an accessory to the device.This device supports up to a 32 GB memory card, formatted to FAT32.Appendix 39
Before you update the software, you can check to the software version installed on your device (Viewing System Software Information, page 33). Then, you can go to garmin.com/support/software/marine.html, select See All Devices in this Bundle, and compare the installed software version to the software version listed for your product.If the software on your device is older than the one listed on the website, follow the steps to load the software on a memory card (Loading the New Software on a Memory Card, page 40), and then update the device software (Updating the Device Software, page 40).Loading the New Software on a Memory CardYou must copy the software update to a memory card using a computer that is running Windows software.NOTE: You can contact Garmin customer support to order a preloaded software update card if you do not have a computer with Windows software.1Insert a memory card into the card slot on the computer.2Go to garmin.com/support/software/marine.html.TIP: You can also download updated owner's manuals to load on the chartplotter from this web page.3Select echoMAP Series with SD Card.4Select Download next to echoMAP Series with SD Card.5Read and agree to the terms.6Select Download.7Choose a location, and select Save.8Double-click the downloaded file.A Garmin folder containing the software update is created in the selected location. A dialog box opens to assist in transferring the software update to a memory card.9Select Next.10Select the drive associated with the memory card, and select Next > Finish.A Garmin folder containing the software update is created on the memory card. The software update can take several minutes to load onto the memory card.Updating the Device SoftwareBefore you can update the software, you must obtain a software-update memory card or load the latest software onto a memory card (Loading the New Software on a Memory Card, page 40).1Turn on the chartplotter.2After the home screen appears, insert the memory card into the card slot.NOTE: In order for the software update instructions to appear, the device must be fully booted before the card is inserted.3Follow the on-screen instructions.4Wait several minutes while the software update process completes.5When prompted, leave the memory card in place and restart the chartplotter manually.6Remove the memory card.NOTE: If the memory card is removed before the device restarts fully, the software update is not complete.Garmin Support CenterGo to support.garmin.com for help and information, such as product manuals, frequently asked questions, videos, software updates, and customer support.40 Appendix
IndexAActiveCaptain 3quickdraw 11smart notifications 4updating charts 4updating software 4aerial photos 7AIS 7, 8, 10alarm 8distress signal device 8SART 8targeting 7, 8threats 8turning on 36vessels 7alarms 18, 35anchor drag 35arrival 35collision 8deep water 22engine 28fuel 28, 35gauges 28navigation 35off course 35shallow water 22sonar 22water temperature 22AM 31anchor drag alarm 35animated currents, tides 6antenna, GPS 2arrival alarm 35Auto Guidance 12, 13, 15, 16, 36paths 15routes 15shoreline distance 16autopilot 25circles pattern 25engaging 25pattern steering 25reducing rudder activity 25steering increment 25steering patterns 25u-turn pattern 25Williamson turn pattern 26zigzag pattern 26Bbacklight 3boundaries, copying 37boundary line 17, 18boundary lines 17Ccelestial information 29charts 4, 6, 8, 10, 11appearance 9details 5fishing 4heading, line 9measuring distance 5navigation 4–6panning 5quickdraw 10, 11symbols 5updating 4clock 35alarm 35collision alarm 8color mode 3combinations 2, 3customizing 2compass 27rose 8courses 12, 13current stations 29indicators 6DDAB 31, 32databackup 37clearing 37copying 37management 36data fields 9deleting, user data 37depth shading 12destinationsnavigation chart 13selecting 13devicecleaning 37keys 1, 2, 5registration 39digital selective calling 29, 30channels 30contacts 29individual routine call 30turning on 29, 36display settings 33distress call 29distress signal device 8DSC. See digital selective callingEEGNOS 33engine gauges 28, 34configuring 28status alarms 28EPIRB 8event log 33Ffactory settings 36sonar 22Fish Eye 3D 8sonar cone 10suspended targets 10tracks 10fishing chart 4panning 5setup 8FM 31fuel capacity 28, 33, 34fuel gauges 28, 34status alarm 28, 35synchronizing with actual fuel 28, 34GGarmin ClearVü 18Garmin Marine Network 35Garmin product support. See product supportgaugesengine 28fuel 28, 34limits 34status alarms 28trip 28wind 28Go To 13GPS 38EGNOS 33signals 2source 2WAAS 33GPS accuracy 35Guide To 13gybing. See tacking and gybingHhazard colors 9headingheading hold 27holding 25line 6, 9help. See product supporthome screen, customizing 2, 3Jjibing. See tacking and gybingKkeel offset 26, 33, 34keys 1, 2power 1, 2Llane width 9language 33Mman overboard 14, 26maps. See chartsmarine services 13mark location 14measuring distance, charts 5media player 30–33alphabetical search 31DAB 31, 32device name 33FUSION-Link 30muting 31preset 31radio 32repeating 31shuffling 31SiriusXM Satellite Radio 32source 30tuner region 31tuning mode 31VHF 31zones 31memory card 37detailed maps 37installing 2slot 1MOB, device 8music player 30, 32. See media playerNnavaids 5navigation alarms 35navigation chart 4, 6, 13aerial photos 8marine service points 13panning 5setup 8, 36vessel trails 10, 30navigation inset 9NMEA 0183 29, 35, 39NMEA 2000 35, 38notifications 4Ooff course alarm 35other vesselsAIS 10trails 10overlay numbers 9Pphotos, aerial 7position, tracking 29position report 30power key 1, 33powerboat 3, 26premium charts 6, 8aerial photos 7Fish Eye 3D 10tide and current indicators 6presets 31, 32DAB 32product registration 39product support 40Qquickdraw 11Index 41
quickdrawsettings 12Rradio 31AM 31FM 31SiriusXM 32, 33range rings 9registering the device 39resetting, settings 33Route To 12, 13routes 13, 14, 17copying 37creating 14deleting 15editing 14navigating 15navigating parallel to 15sharing 36viewing list of 14waypoints 37Ssafe zone collision alarm 8sailboat 3, 26sailing 10, 26race timer 26starting line 26sailing gauges 28SART 8satellite imagery 6satellite signals, acquiring 2screen, brightness 3screenshots 38capturing 38settings 12, 33, 36system information 33sharing data 36shoreline distance 16shortcuts 2SideVü 18SiriusXM 31Satellite Radio 32SiriusXM Satellite Radio 31–33smart notifications 4softwareupdates 33, 40updating 4, 39, 40sonar 18, 20a-scope 22, 23alarms 22appearance 22bottom lock 21color gain 21color rejection 22cone 10depth 21depth line 21depth scale 22frequencies 23FrontVü 20gain 21Garmin ClearVü 18interference 22noise 21, 22overlay numbers 21Panoptix 19, 20, 23, 24recording 21scroll speed 21sharing 20SideVü 18source 20, 21surface noise 22suspended targets 22views 18waypoint 20whiteline 22zoom 21SOS 14support. See product supportsuspended targets 10symbols 7system information 33, 37Ttacking and gybing 27heading hold 27wind hold 27tide stations 6, 29indicators 6tracks 8, 16, 17clearing 17copying 37deleting 17editing 17list 16navigating 17recording 17saving 16saving as route 17showing 10, 16transducer 18, 20, 22, 24trip gauges 28trip planner. See routestroubleshooting 38Uunit ID 33units of measure 36updates, software 39, 40updatingcharts 4software 4user data, deleting 37Vvessel trails 10, 30VHF radio 29calling an AIS target 30distress calls 29DSC channel 30individual routine call 30voltage 35WWAAS 33waterspeed 34temperature offset 34waypoints 8, 14, 38copying 37creating 5, 14deleting 14editing 14man overboard 14navigating to 14sharing 36showing 10sonar 20tracked vessel 30viewing list of 14weather 8Wi‑Fi 3Wi‑Fi technology 35wind gauges 28wind hold 27adjusting 27wireless devices 35connecting a wireless device 35connecting to a wireless device 3network configuration 35Zzoomchart 5sonar 2142 Index
support.garmin.comOctober 2017190-02242-00_0A

Navigation menu