Garmin 01364 LOW POWER COMMUNICATIONS TRANSMITTER User Manual 2

Garmin International Inc LOW POWER COMMUNICATIONS TRANSMITTER Users Manual 2

Contents

Users Manual 2

zumo® 200 seriesquick start manualfor use with the zūmo 220January 2009 190-01144-01 Rev. A Printed in Taiwan
2Your zūmoSerial number under the batteryMini-USB connector under the weather cap microSD™ card slot under the batteryRelease key: Slide up to open the battery cover.Battery contacts Power button:Press and hold to turn on/off the zūmo.Press quickly to adjust the backlight brightness.SpeakerGPS antennaBattery cover
3Important Information‹ WarningSee the Important Safety and Product Information guide in the product box for product warnings and other important information. ‹ WarningThis product contains a lithium-ion battery. To prevent personal injury or device damage, remove the device from the vehicle when exiting or store it out of direct sunlight. ‹ WarningBefore mounting the zūmo, see the Important Safety and Product Information guide for information about laws pertaining to windshield mounting.Getting StartedInstall the zūmo Battery1. Locate the lithium-ion battery that came in the product box.2. Slide the release key up to open the battery cover on the back of the zūmo. 3. Locate the metal contacts on the end of the lithium-ion battery. 4. Insert the battery so that the metal contacts on the battery match up with the metal contacts inside the battery compartment. 5. Press the battery into place.6. Slide the battery cover back on until it clicks into place.
4Mount Your zūmo in an Automobile1. Pull back the weather cap from the mini-USB connector located on the back of your zūmo.2. Plug the vehicle power cable into the mini-USB connector. 3. Snap the cradle onto the suction cup arm.CradleLeverSuction cup arm4. Remove the clear plastic from the suction cup. Clean and dry your windshield and the suction cup with a lint-free cloth.5. Place the suction cup on the windshield.6. Flip the lever back, toward the windshield. 7. Fit the bottom of your zūmo into the cradle.8. Tilt the zūmo back until it snaps into place.9. Plug the other end of the vehicle power cable into a power outlet in your vehicle. Your zūmo should turn on automatically if it is plugged in and the vehicle is running.Mount Your zūmo on the Motorcyle‹ WarningIncorrectly wiring the power cable with bare wire leads can result in damage to the vehicle or the battery and can cause bodily injury. Garmin strongly recommends having an experienced installer with the proper knowledge of electrical systems install the unit.
5Step 1: Connect Power to the zūmoSelect a suitable and secure location to mount the zūmo on your motorcycle, based on available power sources and safe cable routing.Step 2: Install the Handlebar BaseThe zūmo includes parts for two handlebar installation solutions. Custom mounts can require additional hardware (www.ram-mount.com).A) To install the U-bolt and handlebar base:1. Place the U-bolt around the handlebar, and thread the ends through the handlebar base.2. Tighten the nuts to secure the base. Do not overtighten. NOTE: The recommended torque is 50 lbf-in. Do not exceed torque of 80 lbf-in.Handlebar baseHandlebar U-boltB) To install the handlebar base to the clutch/brake clamp bracket:NOTE: Both 1/4 in. standard and M6 bolts are included. Match the size of the factory bolts on your clutch/brake clamp bracket.1. Remove the two factory bolts on your clutch/brake clamp bracket. 2. Thread the new bolts through the handlebar base, spacers, and clamp bracket. 3. Tighten the bolts to secure the base.Clutch/brake clamp bracketHandlebar baseSpacers
6Base plateCradlePanhead screwsWashersSpacersNutsStep 3: Attach the Base Plate to the zūmo Mount1. Thread the M4 × 40 mm panhead screws through the washers, cradle, spacers, and base plate. 2. Tighten the nuts to secure the base plate. Step 4: Attach the Base Plate to the Handlebar Base1. Align the ball of the handlebar base and the ball of the base plate with the double-socket arm.2. Tighten the knob slightly.3. Adjust for better viewing and operation. 4. Tighten the knob to secure the mount.CradleBase plateDouble-socket armKnobHandlebar base
7Step 5: Install Your zūmo in the Mount1. Fit the bottom of your zūmo into the cradle.2. Tilt the zūmo back until it snaps into place.CradleRelease buttonRemove Your zūmo from Either Mount 1. Press the release tab on the top of the mount to release the zūmo.2. Lift out the zūmo. 3. Place the weather cap on the cradle (motorcycle mount only).Congure the zūmoTo turn on your zūmo, press and hold . Follow the on-screen instructions. Acquire SatellitesGo outdoors to an open area, out of garages, and away from tall buildings. Stop your vehicle, and turn on the zūmo. Acquiring satellite signals may take a few minutes. The bars indicate satellite strength. When the bars are green, the zūmo has acquired satellites signals. Now you can select a destination and navigate to it. Resetting the zūmoIf the zūmo stops functioning, turn the zūmo off and on again. If this does not help, press and hold for 10 seconds. The zūmo should operate normally. You can also remove the battery, and then reinstall it.
8Using the Menu Page➊➋ ➌➍➎➏ ➐➑➒➊ GPS satellite strength.➋ Bluetooth headset status. NOTE: Pages appear differently based on your usage mode and settings. ➌Touch to change usage mode. ➍ Battery status. ➎Current time. Touch to change time settings. ➏Touch to nd a destination. ➐ Touch to view the map. ➑ Touch to adjust the volume. ➒Touch to use the tools such as settings, Where Am I?, Help, and routes.Finding Points of Interest1. Touch Where To? > Points of Interest.2. Select a category.3. Select a destination, and touch go!.To search by name, touch Where To? > Points of Interest > Spell Name.To search in a different area, touch Where To? > Near.Using the Go! Page➊➋➌➍➊ Touch to view the route on the map.➋ Touch to start navigating the route.➌ Touch to view this location and surrounding areas on the map.➍ Touch to save this location to your Favorites.
9Using the Map PageYour route is marked with a magenta line. As you travel, your zūmo guides you to your destination with voice prompts, arrows on the map, and directions at the top of the map. A checkered ag marks your destination. If you depart from the original route, your zūmo recalculates the route and provides new directions.➊ ➋➎➏➍➌➊ Touch to view the next turn (navigating on road).➊ Touch to view the compass (navigating off road).➋ Touch the text bar to view the turn list.➌Touch to zoom in and out.➍ Touch the vehicle icon to view the Where Am I? page.➎Touch to view the trip computer.➏Touch to view the Menu page.
10Taking a DetourIf the road ahead is closed, you can take a detour.NOTE: Detour is not available when navigating off road. 1. With a route active, touch Menu. 2. Touch Detour. The zūmo attempts to nd an alternate route that avoids the current road or the next road on your turn list, and then returns to your original route. If the route you are currently navigating is the only reasonable option, the zūmo might not calculate a detour. Adding a Stop to Your Route1. With a route active, touch Menu > Where To?. 2. Search for the extra stop. 3. Touch go!.4. Touch Add as Via Point to add this stop before your destination. OR Touch Set as new Destination to make this your new nal destination. TipTo add more than one stop, edit the current route. Touch Where To? > Custom Routes.Navigating Off RoadWhen you choose a destination while the off road feature is enabled, the zūmo plots a straight line to the destination. 1. Touch Tools > Settings > Navigation.2. Under Route Preference, touch Off Road.Direction to destinationCustomizable data eldsHeading
11Pairing your Bluetooth® HeadsetYou can listen to zūmo audio with your Bluetooth headset. The rst time you use two devices together, you must “pair” them. Your Bluetooth headset and the zūmo must be turned on and be within 10 meters of each other. After the initial pairing, the two devices can connect automatically each time you turn them on. 1. Touch Tools > Settings > Bluetooth. 2. Enable Bluetooth technology on your zūmo.3. Under connections, touch Add or Change. 4. Enable Find Me/Discoverable/Visible mode on your headset. 5. Touch OK on the zūmo.6. Select your headset, and touch OK.7. Enter the Bluetooth PIN for your headset, if necessary, and touch Done. 8. Touch OK.Using TracBack®Touch Where To? > TracBack to view your recent track. Touch Save to save the track to your Favorites. Touch Go! to retrace your recent path of travel.Securing Your zūmo1. Touch Tools > Settings > Security > Garmin Lock. 2. Enter a 4-digit PIN and drive to a security location.NOTE: If you forget your PIN and your security location, you must send your zūmo to Garmin to get it unlocked. You must also send a valid product registration or proof of purchase. Charging Your nüviCharge your nüvi for at least 4 hours before using on battery power.Connect the vehicle power cable. Connect the USB cable (included in some packages).Connect an AC adapter (optional accessory).•••
12Product RegistrationHelp us better support you by completing our online registration today! Connect to our Web site at http://my.garmin.com. Keep the original sales receipt, or a photocopy, in a safe place.Contact GarminContact Garmin if you have any questions while using your zūmo. In the USA, go to www.garmin.com/support, or contact Garmin USA by phone at (913) 397-8200 or (800) 800-1020.In the UK, contact Garmin (Europe) Ltd. by phone at 0808 2380000.In Europe, go to www.garmin.com /support and click Contact Support for in-country support information, or contact Garmin (Europe) Ltd. by phone at +44 (0) 870.8501241.More InformationFor more information about your zūmo, touch Tools > Help. You can download the latest version of the owner’s manual from www.garmin.com. For information about accessories, go to http://buy.garmin.com or contact your Garmin dealer. © 2009 Garmin Ltd. or its subsidiariesGarmin®, zūmo®, and TracBack® are trademarks of Garmin Ltd. or its subsidiaries, registered in the USA and other countries. Garmin Lock™ is a trademark of Garmin Ltd. or its subsidiaries. These trademarks may not be used without the express permission of Garmin. microSD™ is a trademark of the SD Card Association. Other trademarks and trade names are those of their respective owners.

Navigation menu