Garmin 01088 VIRB User Manual

Garmin International Inc VIRB

User Manual

VIRB™ SeriesOwner’s ManualAugust 2013 190-01627-00_0A Printed in Taiwan
All rights reserved. Under the copyright laws, this manual may not be copied, in whole or in part, without the written consent of Garmin. Garmin reserves the right to change or improve its products and to make changes in the content of this manual without obligation to notify any person or organization of such changes or improvements. Go to www.garmin.com for current updates and supplemental information concerning the use of this product.Garmin® and the Garmin logo are trademarks of Garmin Ltd. or its subsidiaries, registered in the USA and other countries. VIRB™, ANT+™, and BaseCamp™ are trademarks of Garmin Ltd. or its subsidiaries. These trademarks may not be used without the express permission of Garmin.microSD™ and the microSDXC logo are trademarks of SD-3C, LLC. Mac® is a trademark of Apple Inc. Microsoft® and Windows® are registered trademarks of Microsoft Corporation in the United States and other countries. HDMI® is a registered trademark of HDMI Licensing, LLC. Wi-Fi® is a registered mark of Wi-Fi Alliance Corporation. Other trademarks and trade names are those of their respective owners.
Table of ContentsIntroduction.................................................................... 1Installing a Memory Card........................................................... 1Installing the Battery Pack......................................................... 1Charging the Lithium-Ion Battery Pack...................................... 1Keys........................................................................................... 2Mounting the Device.................................................................. 2Turning On the Device............................................................... 2Modes........................................................................................ 3Viewfinder....................................................................... 3Leveling the Device.................................................................... 3Status Page............................................................................... 3Video............................................................................... 3Recording a Video..................................................................... 3Video Settings............................................................................ 4Advanced Recording Settings.................................................... 4Recording Video Automatically.................................................. 4Recording a Time Lapse Video.................................................. 4Recording a Video Loop............................................................ 5Connecting an External Microphone or Audio Source............... 5Photos............................................................................. 5Taking a Photo........................................................................... 5Photos Settings.......................................................................... 5Taking a Delayed Photo............................................................. 5Taking Repeated Photos........................................................... 5Playback......................................................................... 5Viewing Photos and Videos....................................................... 5Viewing Video Over HDMI®....................................................... 6Connecting Headphones........................................................... 6Outputting Composite Video...................................................... 6Deleting Photos and Videos....................................................... 6Tracks............................................................................. 6Recorded Track Log Data.......................................................... 6Dashboards.................................................................... 7Viewing the Dashboards............................................................ 7Pairing Your ANT+ Sensors....................................................... 7Remote Control.............................................................. 7Controlling the Device Remotely................................................ 8Controlling Multiple VIRB Devices Remotely............................. 8Operating the Device Using Your Mobile Device....................... 8Troubleshooting.............................................................8My device does not turn on........................................................ 8My device display is hard to see................................................ 8Some information is missing from the dashboards.................... 8My video recordings do not look smooth................................... 8My device turns off when I stop recording video........................ 8Device Information.........................................................8System Settings......................................................................... 8Erasing Your Memory Card....................................................... 9Extending the Battery Life.......................................................... 9Device Care............................................................................... 9File Types.................................................................................. 9Connecting the Device to Your Computer................................. 9Support and Updates................................................................. 9Specifications............................................................................. 9Getting More Information........................................................... 9Index..............................................................................10Table of Contents i
Introduction WARNINGSee the Important Safety and Product Information guide in the product box for product warnings and other important information.It is your responsibility to use the device in a safe manner. Garmin® will not be responsible for any property damage, injuries or deaths resulting from any use of this device in any activities.Installing a Memory CardYou must install a microSD™ memory card up to 64GB to use your device. For optimal performance, use a class 10 or better memory card.1Turn the D-ring counter-clockwise, and pull up to remove the cover.2If necessary, remove the battery pack.3In the battery compartment, slide the card holder À toward the lens, and lift up.4Place the memory card Á with the gold contacts facing down.5Close the card holder.6Slide the card holder away from the lens to lock it.7Replace the battery pack.8Replace the battery cover, and turn the D-ring clockwise.Installing the Battery Pack WARNINGThis product contains a lithium-ion battery. To prevent the possibility of personal injury or product damage caused by battery exposure to extreme heat, store the device out of direct sunlight.1Turn the D-ring counter-clockwise, and pull up to remove the cover.2Locate the metal contacts on the end of the lithium-ion battery.3Insert the battery into the compartment, contacts first.4Press the battery into place.5Replace the battery cover, and turn the D-ring clockwise.Charging the Lithium-Ion Battery PackNOTICETo prevent corrosion, thoroughly dry the mini-USB port, the weather cap, and the surrounding area before charging or connecting to a computer.Do not attempt to use the device to charge a battery that was not provided by Garmin. Attempting to charge a battery that was not provided by Garmin can damage the device and void the warranty.NOTE: The battery will not charge when outside the temperature range of 32 to 114°F (0 to 45°C).You can charge the battery using a standard wall outlet or a USB port on your computer. You can also use an optional battery charger accessory. Go to www.garmin.com/outdoor for more information.1Pull up the weather cap À from the mini-USB port Á.2Plug the small end of the USB cable into the mini-USB port.3Plug the USB end of the cable into the AC adapter or a computer USB port.4Plug the AC adapter into a standard wall outlet.When you connect the device to a power source, the device turns on. The LED is orange while the battery is charging.5Charge the battery completely.The LED turns green when the battery is fully charged.6Remove the USB cable and fully close the weather cap.Battery StatusCritically low battery or missing batteryLow batteryRemaining batteryChargingFully chargedSaving Energy While Charging the DeviceYou can turn off the device display and all other features while charging.1Connect your device to an external power source.The remaining battery capacity appears.2Hold the power key for 4 to 5 seconds.The display turns off, and the device goes into a low power, battery charging mode.3Charge the device completely.Introduction 1
KeysSelect to scroll through menus and settings.Select to scroll through menus and settings.OK Select to choose menu options or to take a photo.MODE Select to scroll through modes.Hold to turn the device on and off.REC Slide toward the lens to record video.Mounting the DeviceNOTICETo prevent product loss or damage, do not use the mounting base when the temperature is below 5°F (-15°C).The permanent mounting adhesive is extremely difficult to remove after it is installed.Before you can install the mounting base onto a surface, the ambient temperature must be from 70° to 100°F (from 21° to 38°C).Your device includes an assortment of mounting bases and arms, which can be used in many configurations. These instructions provide an example of one possible configuration. You can also purchase additional mounts for your device, such as wearable mounts, vehicle mounts, or a tripod mount. Go to www.garmin.com/outdoor for more information.NOTE: By default, the camera should be mounted with the screen facing up to record correctly oriented video. You can adjust the settings to record with the screen facing down (page 4).1Thoroughly clean the mounting surface using water or alcohol.2Remove the film from the base À, and press the base firmly onto the mounting surface.You can use either the flat base or the curved base, depending on the contour of the mounting surface.3Allow the base to bond to the mounting surface for at least 24 hours.4Place the coupler Á into the base.5Place the threaded ring  over the coupler, and tighten it onto the base.6Snap the mounting arm à into the coupler.7Insert a thumbscrew Ä into the larger opening of the joint, and tighten the thumbscrew to lock the angle of the joint.8Snap the camera mount Å into the top of the mounting arm.9Insert a thumbscrew into the larger opening of the joint, and tighten the thumbscrew to lock the angle of the joint.10Place the tab Æ on the back of the camera mount into the slot in the back of the camera.11Squeeze the buttons Ç on the sides of the mount, press the front of the camera È down, and release the buttons.The camera should be held tightly and should not move in the mount when properly secured.12If the camera feels loose in the mount, press the front of the camera into the mount until it clicks.Turning On the DeviceSelect .Turning Off the DeviceNOTICETo prevent loss of data, always turn off the device before removing the battery.NOTE: You cannot turn off the device while recording video.1If necessary, slide REC away from the lens.2Hold .2 Introduction
appears on the screen while the device saves track log data and turns off.If you need to remove the battery, wait until the screen turns off before removing the battery.Turning the Device On and Off Using RECYou can use REC to turn the device on and off in recording mode. This feature allows you to start recording quickly, while automatically turning off the device to conserve battery power when you are not recording.NOTE: The device does not turn off using REC unless you use REC to turn on the device.1With the device turned off, slide REC toward the lens.The device turns on and starts recording video.2When you are finished recording, slide REC away from the lens.The device stops recording and turns off.ModesYou can operate your device in several modes.VIEWFINDER: Displays the camera viewfinder and status information.PLAYBACK: Allows you to view recorded videos and photos.DASHBOARD: Displays sensor data in charts and data fields (VIRB Elite only).SETUP: Allows you to change camera settings.Changing Modes1Select MODE to cycle through the available modes.The modes cycle from left to right. The icon for the selected mode appears larger, and the name of the selected mode appears at the bottom of the screen.2Stop selecting MODE when the desired mode appears.ViewfinderYou can use the viewfinder to set up shots, view status information, and level the camera (VIRB Elite only).Select MODE > VIEWFINDER.ÀBattery statusÁRecording time remaining on the memory cardÂCurrent video modeSelect to view the level (page 3).Select to view the status page (page 3).Leveling the DeviceNOTE: This feature is available for VIRB Elite only.You can use the on-screen level when you mount the device to ensure your videos and photos are perfectly level.1Select MODE > VIEWFINDER > .The level appears.2Adjust the device until the degree of roll À and degree of pitch Á are both 00°, and the brown section of the level  is even with the horizon line Ã.Calibrating the LevelYou can calibrate the level if it does not seem accurate. It may be necessary to calibrate the level when using the device in extreme temperatures.1Place the device flat on a level surface, with the screen facing up.2Select MODE > VIEWFINDER > .3Select OK.Status PageThe status page provides at-a-glance details about the current settings of your device. Select MODE > VIEWFINDER > .ÀDisplays the video mode, field of view, elapsed time, interval or loop setting (if set), number of videos, and time remaining on the memory card.ÁDisplays the photo resolution, camera mode, timer count (if set), photos remaining, and number of photos.ÂDisplays the sensors (VIRB Elite only) including Wi-Fi®, cadence, heart rate, tempe™, and GPS.VideoRecording a VideoNOTE: If the battery power becomes very low while recording video, the device automatically stops recording, saves the video, and safely turns off.1Slide REC toward the lens to start recording video.If the device is off, it turns on automatically. The device starts recording video, and the viewfinder appears.Viewfinder 3
The viewfinder displays the recording status À, the GPS and battery status Á, and the elapsed recording time Â.2When you are finished recording video, slide REC away from the lens.The video is saved on the memory card as an MP4 file, and the track log for the video is saved on the memory card as a GPX file.Video SettingsSelect MODE > SETUP > VIDEO.Mode: Sets the resolution, aspect ratio, and frame rate.Field of View: Sets the zoom level.Loop: Enables loop recording and sets the number of minutes of video to store when recording a video loop.Auto Record: Enables automatic recording (VIRB Elite only).Microphone: Enables the microphone.NOTE: This setting is not available when the device is connected to an external microphone.TIP: If wind noise is an issue when recording video, you can disable the microphone.Video ModesYou can set the resolution, aspect ratio, frame rate, and speed of recorded video. The resolution is the width and height of the video, in pixels. The aspect ratio is the ratio of the video width to the video height. Standard widescreen televisions use a 16:9 aspect ratio, and standard full screen televisions use a 4:3 aspect ratio. The frame rate is expressed in frames per second (fps). The speed indicates the speed of action in the video compared to real time.1080p: Use this mode when you need high-resolution widescreen shots. 1080p works well as a default setting.Tall HD: Use this mode when you need a large, vertical viewing area. Tall HD is particularly useful for close-up action shots and when using a helmet mount.Fast HD: Use this widescreen mode to capture high-speed action shots.Economy HD: Use this widescreen mode when you need a longer recording time. Economy HD uses less space on your memory card.Slow Mo HD: Use this widescreen mode to capture handheld shots with slow-motion playback.Super Slow Mo: Use this mode when you need super slow-motion playback in standard definition.Time Lapse: Use this high-resolution widescreen mode to capture slow-moving or long-term action.Video Mode SpecificationsMode Resolution (pixels)Aspect RatioFrame Rate (fps)Speed1080p 1920×1080 16:9 30 NormalTall HD 1280×960 4:3 48 NormalFast HD 1280×720 16:9 60 NormalEconomy HD 1280x720 16:9 30 NormalMode Resolution (pixels)Aspect RatioFrame Rate (fps)SpeedSlow Mo HD 1280×720 16:9 60 1/2 speedSuper Slow Mo 848×480 16:9 120 1/4 speedTime Lapse 1920×1080 16:9 30 VariesField of ViewYou can change the field of view when Lens Correct is set to Off. Select MODE > SETUP > VIDEO > Field of View.Wide: Captures a wide view of your surroundings. Use this mode for open areas, close-range video, and when you want to capture as much of your viewing area as possible.Zoom (2x): Captures a tighter view. Use this mode for medium-range video.Ultra-Zoom (4x): Captures a very focused view. Use this mode for long-range video and closed or covered surroundings.Advanced Recording SettingsSelect MODE > SETUP > ADVANCED.Lens Correct: Corrects wide-angle barrel distortion and reduces the field of view. Automatically sets Field of View to Wide in the video settings. On+Stabilize turns on image stabilization to reduce shaky video.Flip Camera: Sets the camera to capture video and images with the screen facing up or down. This Side Down captures correctly oriented video and photos with the screen facing downward.Inverting the Camera OrientationYou can change the camera orientation of your device to easily access REC during an activity. If you are mounting the device above your head, you can invert the camera orientation to aid visibility of the recording light or display.1Select MODE > SETUP > ADVANCED > Flip Camera.2Select an option:• Use This Side Up to use the device with the screen facing upward.• Use This Side Down to use the device with the screen facing downward.Recording Video AutomaticallyNOTE: This feature is available for VIRB Elite only.You can set the device to record video automatically based on your activity. This feature allows you to conserve space on your memory card by recording only the important parts of your activity.1Select MODE > SETUP > VIDEO > Auto Record.2Select an option:• To record video automatically when the device is moving, select When Moving.The device records video when you are moving and stops recording when you are still.• To record video automatically when you are skiing, select Ski Mode.The device records video when you are moving downhill and stops recording when you board the chairlift.This feature automatically enables GPS in the system settings.Recording a Time Lapse VideoTime lapse mode captures individual video frames at longer intervals and creates a video that plays much faster than real time. You can use time lapse to record movements, changes, or events that take place over a long period of time.4 Video
Time lapse videos play at 30 frames per second. The length of the video depends on the amount of time between video frames. For example, if frames are recorded at a one-second interval, each second of video covers 30 seconds of real time. If frames are recorded at a 60-second interval, each second of video covers 30 minutes of real time.1Select MODE > SETUP > VIDEO > Mode > Time Lapse.2Select a time interval.3For the best results, mount the device so that it will not move while recording.4Record a video.Recording a Video LoopLoop mode allows you to record video continuously but save only the most recent video footage. You can select the number of minutes of video to save. This enables you to save storage space when you want to capture key moments but do not want to save all footage of an activity. This feature is useful when using the device as a driving recorder.The saved video loop is split into multiple files of equal length. This allows you to delete unwanted portions of the video easily.1Select MODE > SETUP > VIDEO > Mode > Loop.2Select the number of minutes of video to save.Max uses all available storage space on the memory card.3Start recording video.4When finished, stop recording.The most recent footage is saved on the memory card, up to the number of minutes selected in step 2.Connecting an External Microphone or Audio SourceBefore you can connect an external microphone, you must purchase a VIRB accessory cable with audio input. Go to www.garmin.com/outdoor. You must also have an external microphone or audio source with a 3.5 mm connector.When you connect an external microphone, the device records audio from the external microphone instead of the built-in microphone.1Pull up the weather cap from the mini-USB port.2Connect mini-USB plug on the accessory cable to the mini-USB port on the device.3On the device, when prompted to output video, select No.4On the device, when prompted to use an external microphone, select Yes.5Connect the microphone to the MIC IN connector on the accessory cable.To stop using the external microphone, you must disconnect the accessory cable from the device.PhotosTaking a PhotoYour device provides several methods for taking a photo.• Select MODE > VIEWFINDER, aim the camera using the viewfinder, and select .• From anywhere except the playback screen, hold .The device displays the photo briefly and returns to the page you were using.• While recording a video, select to capture a photo at the same resolution as the video recording.Photos taken while recording a video always use normal photo mode. Burst mode is ignored while recording video.Photos SettingsSelect MODE > SETUP > Photos.Resolution: Sets the photo resolution to 16 MP (4:3), 12 MP (16:9), or 8 MP (4:3).Mode: Sets the shooting mode. Burst mode takes several photos in quick succession to capture a specific instance, such as the finish line during a race.Self Timer: Sets the timer to delay taking a photo. Repeat On automatically repeats the time interval and captures a photo until you press again.Date Stamp: Adds a date stamp to your photo.Photo ModesSelect MODE > SETUP > Photos > Mode.Normal: Takes a single photo using automatic exposure.Burst: Rapidly takes three 16MP images, five 12MP images, or ten 8MP images in one second. Burst mode is ideal for capturing photos of people or objects in motion.Taking a Delayed PhotoYou can delay taking a photo using the self timer. This allows you to join or adjust a shot before the photo is taken.1Select MODE > SETUP > Photos > Self Timer.2Select a delay time.3Select Repeat Off.Repeat Off is not an option when Burst mode is enabled.4Select MODE > VIEWFINDER.5Select .The countdown timer displays the remaining time until the photo is taken, in seconds.Taking Repeated PhotosYou can use the self timer to take repeated photos at a set time interval. This enables you to take several photos of a subject or to take a series of time-lapse photos.1Select MODE > SETUP > Photos > Self Timer.2Select a time interval between photos.3Select Repeat On.4Select MODE > VIEWFINDER.5Select .The device takes repeated photos at the selected interval. The viewfinder displays the GPS and battery status À, the time in seconds until the next photo is taken Á, and the number of repeated photos the device has taken Â.6Select to stop taking photos.PlaybackViewing Photos and VideosYou can view your photos and recorded videos on the device screen.Photos 5
1Select MODE > PLAYBACK.2Select an option:• To select a photo or video, select or .• To quickly scroll through the list, hold or .Videos are indicated with . Videos and photos are sorted by date and time with the most recent item listed first.3Select OK.You can control video playback using the on-screen controls.Viewing Video Over HDMI®You can connect your device to an external display using an HDMI-to-micro HDMI cable (not included).1If necessary, turn on the device.2Pull up the weather cap À from the micro HDMI port Á.3Plug the small end of the HDMI cable into the micro-HDMI port.4Plug the large end of the cable into an available HDMI port on the external display.5On the device, select MODE > PLAYBACK.6Select and to select a video.7Select OK.The video plays on the external display.Connecting HeadphonesBefore you can connect headphones to your device, you must purchase the VIRB audio-video cable accessory. Go to www.garmin.com/outdoor.Using headphones, you can monitor the audio when recording a video and listen to your recorded video in PLAYBACK on the device.1Pull up the weather cap from the mini-USB port.2Connect the mini-USB plug on the audio-video cable to the mini-USB port on the device.3Connect the headphones to the 3.5 mm AUDIO OUT connector on the audio-video cable.Your device automatically detects the audio-video cable and displays a setup wizard.4On the device, when prompted to output video, select No.5On the device, when prompted to use an external microphone, select No.To stop using the headphones, you must disconnect the audio-video cable from the device.Adjusting the VolumeWhen headphones are connected to your device, you can adjust the volume.1Select MODE > SETUP > SYSTEM > Audio Out.2Select and to change the volume level.3Select OK.Outputting Composite VideoBefore you can output composite video, you must purchase the VIRB audio-video cable accessory. Go to www.garmin.com/outdoor. You must also have an RCA composite video cable and a 3.5 mm stereo audio cable.You can play video on an external display using composite video and stereo audio.1Pull up the weather cap from the mini-USB port.2Connect mini-USB plug on the audio-video cable to the mini-USB port on the device.3On the device, when prompted to output video, select Yes.4Connect an RCA composite video cable to the composite video output connector of the audio-video cable and to an available port on your external display.5Connect a 3.5 mm audio cable to the AUDIO OUT connector on the audio-video cable and to an available port on your external display.TIP: If your external display requires RCA audio input, you can use a 3.5 mm-to-RCA adaptor cable.Deleting Photos and Videos1Select MODE > PLAYBACK.2Select and to select a photo or video.3Select OK > .TracksNOTE: This feature is available for VIRB Elite only.A track is a recording of your path. The track log contains information about points along the recorded path, such as time, location, and elevation for each point. If you have paired ANT+™ sensors with your device, data from connected sensors is included in the track log.The device records a continuous track log while it is on. This track is saved as a FIT file on the memory card each time you turn off the device. The device also records a separate track log for each video recording. Video track logs are saved as GPX files on the memory card each time you stop recording video. The track logs include track point data at one-second intervals.You can view GPX and FIT track logs on your computer using the BaseCamp™ application. Go to www.garmin.com/basecamp for more information. You can also view and upload FIT track logs to Garmin Connect™. Go to http://connect.garmin.com for more information.Recorded Track Log DataEach point in the track log records your GPS location and data from available sensors. The device can record these categories of data in the track log.• GPS location• Speed• Distance from the starting point• Time• Elevation• G-force• Heart rate (when connected to a compatible heart rate monitor)• Cadence (when connected to a compatible bicycle cadence sensor)• Temperature (when connected to a compatible temperature sensor6 Tracks
DashboardsNOTE: This feature is available for VIRB Elite only.A dashboard is a grouping of data fields, charts, or graphs of data from the device sensors and connected ANT+ sensors. The dashboards provide real-time and historical views of the sensor data recorded to the track log.NOTE: All minimum, maximum, and average dashboard data resets after you turn off the device.Compass displays the current heading and partial compass ring. You must be moving to use the compass.Time displays the time since the device was turned on À, time of day Á, and time of sunset or sunrise Â.Distance displays the total distance À, total descent Á, and total ascent Â.Speed displays the current speed À, average speed Á, and maximum speed Â.Elevation displays the current elevation À, maximum and minimum elevations Á, elevation graph Â, and time scale Ã.G-force displays the current g-force acceleration À and maximum g-force acceleration Á.When connected to a sensor, heart rate displays the current heart rate À, maximum and minimum heart rates Á, heart rate graph Â, and time scale Ã.When connected to a sensor, tempe displays the current temperature À, maximum and minimum temperatures Á, temperature graph Â, and time scale Ã.When connected to a sensor, cadence displays the current cadence À, maximum and minimum cadences Á, cadence graph Â, and time scale Ã.Viewing the Dashboards1Select MODE > DASHBOARD.2Select or to scroll through the dashboards.Pairing Your ANT+ SensorsWhen you pair a compatible ANT+ sensor with your device, the sensor data is included in the track log, and you can view dashboards for the sensor data.1Turn on the sensor, and bring the device and sensor within 10 ft. (3 m) of each other.2On the device, select MODE > SETUP > SENSORS.3On the device, select the type of sensor to pair.The icon for the sensor blinks. When the icon turns solid, the sensor is paired and connected.Remote ControlYou can start recording, stop recording, and take pictures on your VIRB device using another compatible Garmin device with ANT+ wireless technology, such as the VIRB remote control accessory or the fēnix™ watch. You can also use your VIRB device to control other VIRB devices.Dashboards 7
Controlling the Device Remotely1On your VIRB device, select MODE > SETUP > Remote.2Select VIRB Type > Main VIRB.3Select an option:• On the remote control device, launch the VIRB app or feature. See the owner's manual for the device for more information.• On the remote control accessory, follow the pairing instructions in the accessory manual.Controlling Multiple VIRB Devices RemotelyWhen controlling multiple VIRB devices, you must choose a main VIRB device. This device controls all your other VIRB devices.If you are using a remote control device with multiple VIRB devices, the remote control device controls only the main VIRB device. The main VIRB device passes commands received from the remote control device to the other VIRB devices.1On all of your VIRB devices, select MODE > SETUP > Remote.2On your main VIRB device, select VIRB Type > Main VIRB.3On each of your other VIRB devices, select VIRB Type > Extended VIRB.REC on your main VIRB device starts and stops recording video on all your VIRB devices. on your main VIRB device takes a photo from all your VIRB devices.4If you are using a remote control device, select an option:• On the remote control device, launch the VIRB app or feature. See the owner's manual for the device for more information.• On the remote control accessory, follow the pairing instructions in the accessory manual.Operating the Device Using Your Mobile DeviceNOTE: This feature is available for VIRB Elite only.You can remotely view and control photo and video recording using a compatible mobile device running the free Garmin VIRB app. The app connects using a direct Wi-Fi connection between your VIRB device and your compatible mobile device. Go to www.garmin.com or the application store for your mobile device for compatibility information.1If necessary, install the Garmin VIRB app from the application store on your mobile device.2On your VIRB device, select MODE > SETUP > WIFI > WIFI.The VIRB device enters wireless host mode, and the SSID and password appear on the device screen.3On your mobile device, go to the wireless settings and connect to the wireless network that matches the SSID on the VIRB device screen.See the owner's manual for your mobile device for more information.4On your mobile device, enter the password that appears on the VIRB device screen.5On your mobile device, start the Garmin VIRB app.Advanced Wireless SettingsYou can change the wireless host settings for your device. Select MODE > SETUP > WIFI > Advanced.SSID: Sets the SSID, which identifies your VIRB device on other devices.Password: Sets the password used to connect to your VIRB device.TroubleshootingMy device does not turn on• Install a memory card (page 1).The device does not boot if a memory card is not installed.• Verify the battery is installed correctly (page 1).• Fully charge the battery (page 1).My device display is hard to seeThe device has a reflective display that maximizes battery life and is readable in direct sunlight. The display does not have a backlight and requires ambient light for visibility. If the display looks dark or hard to see, you should increase the ambient light or go to a brighter area.Some information is missing from the dashboardsDashboards are available only for VIRB Elite devices (page 7). Some dashboard information requires you to enable or pair sensors.• Enable GPS (page 8), and go to an area with a clear view of the sky.Location, speed, distance, and altitude information requires a GPS signal.• Connect additional ANT+ sensors (page 7).Some dashboards are available only when a compatible ANT+ sensor is connected.My video recordings do not look smooth• If video recordings appear shaky, select MODE > SETUP > VIDEO > Lens Correct > On+Stabilize to enable image stabilization.• If video recordings stutter or skip frames, install a class 10 or better microSD memory card (page 1).The device requires a class 10 or better memory card to record smooth high-definition video.My device turns off when I stop recording videoIf you turn on the device by sliding REC toward the lens, the device turns off when you slide REC away from the lens. This allows you to maximize battery life by turning off the device when it is not recording.Device InformationSystem SettingsSelect MODE > SETUP > SYSTEM.GPS: Enables the device to receive GPS satellite signals. When Recording enables GPS reception only when the camera is recording video (VIRB Elite only).NOTE: GPS must be set to On to enable Auto Record.Record Light: Turns the recording light on or off.Tones: Turns audible tones on or off.Time: Sets the time and date formats.Units: Sets the units of measure.Language: Sets the on-screen text language.Reset Settings: Restores the default device settings.About: Displays important software information and your unit ID.8 Troubleshooting
Time SettingsSelect MODE > SETUP > Time/Date.Time: Sets the time.NOTE: VIRB Elite devices set the time automatically when you enable GPS.Time Format: Sets the device to show time in a 12-hour or a 24-hour format.Date: Sets the date.NOTE: VIRB Elite devices set the date automatically when you enable GPS.Date Format: Sets the device to show dates in a MM/DD/YY or a DD/MM/YY format.Time Zone: Sets the time zone for the device. Automatic sets the time zone automatically based on your GPS position (VIRB Elite only).Erasing Your Memory CardNOTICEErased data cannot be restored.You can erase all photos, videos, and other data on the memory card installed in your device.Select MODE > SETUP > CARD > Erase > OK.Extending the Battery LifeNOTE: GPS and ANT™ do not significantly affect battery life.• Disable Wi-Fi.• Turn the device on and off using REC (page 3).• Use automatic recording (page 4).Device CareNOTICEAvoid chemical cleaners, solvents, and insect repellents that can damage plastic components and finishes.Do not store the device where prolonged exposure to extreme temperatures can occur, because it can cause permanent damage.The device is water resistant to IEC Standard 60529 IPX7. It can withstand immersion in 1 meter of water for 30 minutes. Prolonged submersion can cause damage to the device. After submersion, be certain to wipe dry and air dry the device before using or charging.Cleaning the DeviceNOTICEDo not use a dry cloth to clean the lens. Use of a dry cloth may damage the fog resistant coating on the lens.Wipe the device with a soft, non-scratch cloth dampened with water or alcohol.File TypesThe device supports these file types.• GPX track files (output only).• JPEG photo files.• MP4 video files.• FIT files for exporting to Garmin Connect (output only).Connecting the Device to Your ComputerNOTICETo prevent corrosion, thoroughly dry the mini-USB port, the weather cap, and the surrounding area before charging or connecting to a computer.Before you can connect the straight connector of the USB cable to your device, you may have to remove optional mount accessories.1Pull up the weather cap from the mini-USB port.2Plug the small end of the USB cable into the mini-USB port.3Plug the large end of the USB cable into a computer USB port.Your device and memory card (optional) appear as removable drives in My Computer on Windows® computers and as mounted volumes on Mac® computers.Support and UpdatesThe Garmin VIRB application provides easy access to these tools and services for your device.• Reviewing and editing recorded videos• Reviewing track logs• Linking track logs to your recorded videos• Software and feature updatesThe Garmin VIRB application is available for Windows and Mac computers. Go to www.garmin.com/VIRB for more information.SpecificationsBattery type Rechargeable Lithium-ion batteryBattery life Up to 3 hoursWater resistance Water resistant to IEC 60529 IPX7Operating temperature rangeFrom 5º to 140ºF (from -15º to 60ºC)Charging temperature rangeFrom 32º to 113°F (0º to 45°C)Radio frequency/protocol2.4 GHz ANT+ wireless communications protocolWi-Fi IEEE 802.11 b/g at 2.4 GHzGetting More InformationYou can find more information about this product on the Garmin website.• Go to www.garmin.com/outdoor.• Go to www.garmin.com/learningcenter.• Go to http://buy.garmin.com, or contact your Garmin dealer for information about optional accessories and replacement parts.Device Information 9
IndexAaccessories 9ANT+ sensors 3pairing 7Bbattery 1, 8, 9charging 1installing 1life 9Ccadence 6camerafield of view 4level 3modes 3orientation 4self timer 5settings 3, 5viewfinder 3charging 1cleaning the device 9computer, connecting 9Ddashboards 7, 8data, transferring 9deletingall user data 9pictures 6videos 6device, keys 2Eelevation 6Ffiles, transferring 9GGPS 6settings 3, 8HHDMI output 6headphones, connecting 6heart rate 6Kkeys 2Llanguage 8Mmemory card 1microphone, connecting 5microSD card. See memory cardmounting the device 2mounts, optional 2Pphotossettings 4, 5taking 5viewing 5power key 2, 3Rremote control 7, 8Ssettings 9softwareupdating 9version 8specifications 9speed 6storing data 9system settings 8Ttemperature 6, 9timesettings 9zones and formats 9tones 8tracks 6, 9transferring, files 9troubleshooting 8, 9Uunit ID 8USBmass storage mode 9transferring files 9Vvideoediting 9loop 5output 6playing 5recording 3–5settings 3, 4time lapse 4volume, adjusting 6Wwater resistance 9Wi-Fi 3, 8connecting 810 Index
www.garmin.com/support913-397-82001-800-800-10200808 238 0000+44 870 850 1242 1-866-429-9296 +43 (0) 820 220 230+32 2 672 52 54 +45 4810 5050 +358 9 6937 9758 + 331 55 69 33 99+49 (0)180 6 427646 + 39 02 36 699699 0800 - 023 3937035 - 539 3727 + 47 815 69 55500800 4412 454+44 2380 662 915 + 35 1214 447 460 + 34 93 275 44 97 + 46 7744 52020Garmin International, Inc.1200 East 151st StreetOlathe, Kansas 66062, USAGarmin (Europe) Ltd.Liberty House, Hounsdown Business ParkSouthampton, Hampshire, SO40 9LR UKGarmin CorporationNo. 68, Zhangshu 2nd Road, Xizhi Dist.New Taipei City, 221, Taiwan (R.O.C.)© 2013 Garmin Ltd. or its subsidiaries
Notice This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. For P15B equipment This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.
FCC RF Radiation Exposure Statement:(1) This Transmitter has been demonstrated co-location compliance requirements as documented in this filing.(2) This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment.
Canada—Low‐powerlicense‐exemptradiocommunicationdevices(RSS‐210)a.CommoninformationOperationissubjecttothefollowingtwoconditions:1.Thisdevicemaynotcauseinterference,and2.Thisdevicemustacceptanyinterference,includinginterferencethatmaycauseundesired operationofthedevice.b.Operationin2.4GHzbandTopreventradiointerferencetothelicensedservice,thisdevice isintendedtobeoperatedindoorsandinstallationoutdoorsissubjecttolicensing.Canada‐defaiblepuissanceexemptsdelicencedesappareilsdecommunicationradio(CNR‐210)a.InformationscommunesSonfonctionnementestsoumisauxdeuxconditionssuivantes:1.Cedispositifnepeutcauserdesinterférences,et2.Cedispositifdoitacceptertouteinterférence,ycomprislesinterférencesquipeuventcauserunmauvais fonctionnementdudispositif.b.Lefonctionnementenbandede2,4GHzPourprévenirlesinterférencesradioélectriquesauxservicessouslicence, cetappareilestdestinéàêtreexploitéàl'intérieuretàl'extérieurd'installationestsoumiseàlicence.ICradiationexposurestatementThisEUTiscompliancewithSARforgeneralpopulation/uncontrolledexposure limitsinICRSS‐102andhadbeentestedinaccordancewiththemeasurementmethodsandproceduresspecifiedin IEEE1528.Thisdeviceanditsantenna(s)mustnotbeco‐locatedoroperatinginconjunctionwithanyotherantenna ortransmitter.Note:ThecountycodeselectionfeatureisdisabledforproductsmarketedintheUS/Canada.DéclarationICexpositionauxrayonnementsCetteESTestlerespectdeSARpourlapopulationgénérale/limites d'expositionnoncontrôléedanslesICRSS‐102etaététestéconformémentauxméthodesetprocéduresdemesure spécifiéesdanslanormeIEEE1528.Cetappareiletsonantenne(s)nedoitpasêtreco‐localisésoufonctionner conjointementavecuneautreantenneoutransmetteur.Remarque:Lafonctioncodedecomtédesélectionest désactivéepourlesproduitscommercialisésdanslesÉtats‐UnisetleCanada.

Navigation menu