GVC EPIQ-694 EPIQ Computer User Manual MR804manualX01

GVC International U.S.A., Inc. EPIQ Computer MR804manualX01

UserManual.wiki >

EPIQ 694 User Manual

manual

1 Socket 370 Socket 370 Socket 370 Socket 370 AGP/PCI/ISA AGP/PCI/ISA AGP/PCI/ISA AGP/PCI/ISA MotherboardMotherboardMotherboardMotherboard QS694VPQS694VPQS694VPQS694VP User’s Manual For Support: http://www.bcmcom.com/

2 DeclarationDeclarationDeclarationDeclaration DDDDDDDDeeeeeeeeccccccccllllllllaaaaaaaarrrrrrrraaaaaaaattttttttiiiiiiiioooooooonnnnnnnn Rights:Rights:Rights:Rights: No part of this manual, including but not limited to the products and software described in it, may be reproduced, transmitted, transcribes, stored in a retrieval system, or translated in any form or by any means without the expressed written permission of the manufacture. Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies and are used only for identification or explanation purposes without intent to infringe. !" Intel, MMX and Pentium are registered trademarks of Intel Corporation. !" IBM and OS/2 are registered trademarks of International Business Machines. !" AWARD is a registered trademark of Award Software Inc. !" VIA is a trademark of Technology of VIA Incorporated. !" Creative is a trademark of Creative Technology. Responsibility: Responsibility: Responsibility: Responsibility: This manual is provided “As is” with no warranties of any kind, either expressed or implied, including, but not limited to the implied warranties or conditions of this product’s fitness for any particular purpose. In no event shall we be liable for any loss of profits, loss of business, loss of data, interruption of business, or indirect, special, incidental, or consequential damages of any kind, even the possibility of such damages arising from any defect or error in this manual or product. We reserve the right to modify and update the user manual without prior notice. April 21, 2000 Warning: Replace your system's CMOS RAM battery only with the identical CR-2032 3V Lithium Ion coin cell (or equivalent) battery type, to avoid risk of personal injury or physical damage to your equipment. Always dispose of used batteries according to the manufacturer's instructions, or as required by local ordinance (where applicable).

4 Easy InstallaEasy InstallaEasy InstallaEasy Installationtiontiontion EEEEEEEEaaaaaaaassssssssyyyyyyyy IIIIIIIInnnnnnnnssssssssttttttttaaaaaaaallllllllllllllllaaaaaaaattttttttiiiiiiiioooooooonnnnnnnn Easy Installation StepsEasy Installation StepsEasy Installation StepsEasy Installation Steps The following “Easy Installation” steps are for users accustomed to the assembly of a computer system. For those individuals requiring more specific information, please refer to the more detailed descriptions located within the latter chapters of this manual. Note: You must keep your power cable unplugged until the following installation steps are completed. Getting Started: Getting Started: Getting Started: Getting Started: Touch a grounded metal surface to release static electricity stored in your body before unpacking your motherboard. For details please refer to Precaution section in Chapter 3. Install the CPU by correctly aligning the CPU with the Slot as noted in the motherboard diagram. Once aligned, press down on the CPU gently but firmly and lock it. Next, install the 3.3 volt un-buffered SDRAM into the 168 pin DIMMs. See Sec. 3.4. Set CPU speed in according to Sec.3.3.2. After completing the above steps, install any expansion Cards (PCI, ISA, AMR) into riser card and have the riser card installed firmly into the slot for riser card on board. See Sec. 3.5. Plug in all cables included in the package except for the power cord. Please see Sec. 3.6. Please recheck all steps to ensure no mistakes have been made and then plug in the power cord and turn on the power to enter the BIOS setup, Chapter 4. ReleaseStatic ElectricityInsert CPU & RAM Install AllExpansion SlotsSet Jumpers of CPU CoupleConnectors of HDD, FDD,...!!

5 Table of ContentsTable of ContentsTable of ContentsTable of Contents Declaration ...............................................................................................................2 Compliance & Certificate........................................................................................3 Easy Installation ......................................................................................................4 1. Introduction..........................................................................................................9 1.1 How To Use This Manual.................................................................................9 1.2 Check Your Device Items.................................................................................9 2. Features..............................................................................................................10 2.1 Features Of The Motherboard........................................................................10 3. Installation..........................................................................................................13 3.1 Motherboard Layout & Main Parts..................................................................13 Static Electricity Damage: .................................................................................16 Misplaced Jumper Damage: .............................................................................16 3.2 Slots And Connectors.....................................................................................17 3.3 CPU (Central Processing Unit).......................................................................18 3.3.1 Install CPU ...............................................................................................18 3.3.2 Set CPU Speed........................................................................................19 3.4 System Memory (DRAM) ...............................................................................21 3.4.1 DIMM (Dual Inline Memory Module).........................................................21 3.4.2 Installation Procedure ..............................................................................21 3.4.3 DIMM Module Combinations....................................................................22 3.5 Expansion Slots..............................................................................................23 3.6 Connectors .....................................................................................................24 3.6.1 Primary IDE Connector (J25, 39-pin block, Black)...................................24 3.6.2 Secondary IDE Connector (J24, 39-pin block, White) .............................24 3.6.3 Floppy Drive Connector (J26, 33-pin block).............................................25 3.6.4 Power Input Connector (J22, 20-pin block)..............................................25 3.6.5 Front Panel Connectors (J33-J39, 15-pin)...............................................26 3.6.6 Back Panel Connectors............................................................................29 3.6.7 Additional Connectors ..............................................................................32 4. BIOS Setup.........................................................................................................37 4.1 BIOS Setup.....................................................................................................37 4.1.1 Setup Keys...............................................................................................38 4.1.2 Getting Help .............................................................................................38 4.1.3 In Case of Problems.................................................................................38 4.2 Main Setup Menu ...........................................................................................39 4.3 Standard CMOS Features Menu....................................................................40 4.3.1 Date..........................................................................................................40 4.3.2 Time .........................................................................................................40

6 Table of ContentsTable of ContentsTable of ContentsTable of Contents 4.3.3 Hard Disks................................................................................................41 4.3.4 Drive A/B type ..........................................................................................42 4.3.5 Video........................................................................................................42 4.3.6 Halt on......................................................................................................43 4.3.7 Memory ....................................................................................................43 4.4 Advanced BIOS Features Menu.....................................................................44 4.4.1 Virus Warning...........................................................................................45 4.4.2 External Cache.........................................................................................45 4.4.3 CPU L2 Cache ECC Checking.................................................................45 4.4.4 Processor Number Feature......................................................................45 4.4.5 Quick Power On Self Test........................................................................45 4.4.6 First Boot Device......................................................................................45 4.4.7 Second Boot Device.................................................................................45 4.4.8 Third Boot Device.....................................................................................45 4.4.9 Boot Other Device....................................................................................46 4.4.10 Swap Floppy Drive.................................................................................46 4.4.11 Boot Up Floppy Seek .............................................................................46 4.4.12 Boot Up NumLock Status.......................................................................46 4.4.13 Gate A20 Option ....................................................................................46 4.4.14 Typematic Rate Setting..........................................................................46 4.4.15 Typematic Rate (Chars/Sec)..................................................................46 4.4.16 Typematic Delay (Msec) ........................................................................46 4.4.17 Security Option.......................................................................................47 4.4.18 OS Select for DRAM > 64MB.................................................................47 4.4.19 Report No FDD For WIN 95...................................................................47 4.4.20 Video BIOS Shadow ..............................................................................47 4.4.21 C8000-CBFFF to DC000-DFFFF...........................................................47 4.5 Advanced Chipset Features Menu .................................................................48 4.5.1 SDRAM Cycle Length ..............................................................................48 4.5.2 DRAM Frequency.....................................................................................49 4.5.3 Memory Hole............................................................................................49 4.5.4 System BIOS Cacheable .........................................................................49 4.5.5 Video RAM Cacheable.............................................................................49 4.5.6 AGP Aperture Size...................................................................................49 4.5.7 AGP-4X Mode..........................................................................................49 4.5.8 AGP Driving Control.................................................................................49 4.5.9 AGP Driving Value ...................................................................................49 4.5.10 OnChip USB...........................................................................................50 4.5.11 OnChip FrontSide USB..........................................................................50 4.5.12 USB Keyboard Support..........................................................................50 4.5.13 OnChip Sound........................................................................................50 4.5.14 OnChip Modem......................................................................................50

7 Table of ContentsTable of ContentsTable of ContentsTable of Contents 4.5.15 CPU to PCI Write Buffer.........................................................................50 4.5.16 PCI Dynamic Bursting............................................................................50 4.5.17 Master 0 WS Write.................................................................................50 4.5.18 PCI Delay Transaction ...........................................................................51 4.5.19 PCI#2 Access #1 Retry..........................................................................51 4.5.20 AGP Master 1 WS Write ........................................................................51 4.5.21 AGP Master 1 WS Read ........................................................................51 4.5.22 Memory Parity/ECC Check ....................................................................51 4.6 Integrated Peripherals ....................................................................................52 4.6.1 OnChip IDE Channel 0.............................................................................52 4.6.2 OnChip IDE Channel 1.............................................................................53 4.6.3 IDE Prefetch Mode...................................................................................53 4.6.4 IDE Primary/Secondary Master/Slave PIO ..............................................53 4.6.5 IDE Primary/Secondary Master/Slave UDMA..........................................53 4.6.6 Init Display First........................................................................................53 4.6.7 IDE HDD Block Mode...............................................................................53 4.6.8 Onboard FDD Controller ..........................................................................53 4.6.9 Onboard Serial Port 1/Port 2....................................................................54 4.6.10 UART 2 Mode ........................................................................................54 4.6.11 IR Function Duplex.................................................................................54 4.6.12 TX, RX inverting enable .........................................................................54 4.6.13 Onboard Parallel Port.............................................................................54 4.6.14 Onboard Parallel Mode ..........................................................................54 4.6.15 ECP Mode Use DMA..............................................................................54 4.6.16 Parallel Port EPP Type ..........................................................................55 4.6.17 SB I/O Base Address .............................................................................55 4.6.18 SB IRQ Select ........................................................................................55 4.6.19 SB DMA Select.......................................................................................55 4.6.20 MPU-401................................................................................................55 4.6.21 MPU-401 I/O Address............................................................................55 4.6.22 Game Port (200-207H)...........................................................................55 4.7 Power Management Setup Menu...................................................................56 4.7.1 ACPI function ...........................................................................................56 4.7.2 Power Management.................................................................................57 4.7.2.1 PM Timers ..................................................................................................57 4.7.3 PM Control by APM..................................................................................57 4.7.4 Video Off Option.......................................................................................58 4.7.5 Video Off Method .....................................................................................58 4.7.6 Modem Use IRQ ......................................................................................58 4.7.7 Soft-Off by PWRBTN ...............................................................................58 4.7.8 Keyboard Power On.................................................................................58 4.7.9 Wake-Up Events ......................................................................................59

8 Table of ContentsTable of ContentsTable of ContentsTable of Contents 4.8 PnP/PCI Configurations Menu .......................................................................60 4.8.1 PNP OS Installed .....................................................................................60 4.8.2 Reset Configuration Data.........................................................................60 4.8.3 Resources Controlled By .........................................................................60 4.8.4 PCI/VGA Palette Snoop ...........................................................................60 4.8.5 Assign IRQ for VGA .................................................................................61 4.8.6 Assign IRQ for USB .................................................................................61 4.9 PC Health Status............................................................................................62 4.9.1 Chassis Intrusion......................................................................................62 4.10 Frequency/Voltage Control...........................................................................63 4.10.1 Auto Detect DIMM/PCI Clk.....................................................................63 4.10.2 Spread Spectrum ...................................................................................63 4.11 Load Optimized Defaults..............................................................................64 4.12 Set User Password.......................................................................................64 4.13 Save & Exit Setup.........................................................................................64 4.14 Exit Without Saving ......................................................................................64

9 1. Introduction1. Introduction1. Introduction1. Introduction 11111111........ IIIIIIIInnnnnnnnttttttttrrrrrrrroooooooodddddddduuuuuuuuccccccccttttttttiiiiiiiioooooooonnnnnnnn 1.1 How To Use This Manual1.1 How To Use This Manual1.1 How To Use This Manual1.1 How To Use This Manual This manual provides information necessary for Original Equipment Manufactures (OEMs) and home users to build a PC-AT compatible system using the Pentium III PCI/ISA/AGP motherboard. Follow the installation procedure presented on the Easy Installation Page and refer to the section number following each step if you require more detailed instructions. USER MANUAL 1.2 Check Your Device Items1.2 Check Your Device Items1.2 Check Your Device Items1.2 Check Your Device Items The standard package should contain the following items. If you find any of these items be missing or damaged, please contact your retailer. !"The motherboard !"1 IDE ribbon cable !"1 floppy ribbon cable !"1 CD with drivers of VIA694X/686A, Creative ES1373 (optional) !"1 User’s Manual !"1 Norton Anti-Virus CD (optional) CHECK ITEMS

10 2. Features2. Features2. Features2. Features 22222222........ FFFFFFFFeeeeeeeeaaaaaaaattttttttuuuuuuuurrrrrrrreeeeeeeessssssss 2.1 Features Of The Motherboard2.1 Features Of The Motherboard2.1 Features Of The Motherboard2.1 Features Of The Motherboard This product is based on the “ATX” form factor. It features advanced functions and provides support for the business PC maker. This motherboard incorporates VIA 694X/686A chipset and provides features such as 4X AGP slot, Ultra DMA 33/66 IDE Interface and ACPI power management. Processor Processor Processor Processor !" Support Intel Socket 370 Processor, with 66/100/133 MHz host bus speed ChipsetChipsetChipsetChipset !" VIA VT82C694X, VT82C686A chipset System MeSystem MeSystem MeSystem Memory mory mory mory !" Three 168-pin DIMM sockets !" Minimum 8MB up to maximum 1.5 GB Memory Capacity !" 66MHz / 100MHz / 133MHz SDRAM, Virtual Channel Memory (VCM) DIMM module Graphic SupportGraphic SupportGraphic SupportGraphic Support !" Support full AGP V2.0 capability for maximum bus utilization including 2x and 4x mode transfers, SBA (Side Band Addressing), Flush/Fence commands, and pipelined grants, in a 132 pin Universal AGP slot PCI Bus Master IDE ControllerPCI Bus Master IDE ControllerPCI Bus Master IDE ControllerPCI Bus Master IDE Controller !" Support for up to 4 IDE devices. !" PIO Mode 4 transfers at up to 16MB/Sec. !" Support for Ultra ATA/33 and Ultra ATA/66 devices, transfers at up to 66MB/Sec. !" Support CD-ROM, Backup machines and LS120 floppy disk driver through IDE interface.

11 2. Features2. Features2. Features2. Features Integrated I/OIntegrated I/OIntegrated I/OIntegrated I/O !" 1 Floppy Port (up to 2.88 MB) !" 1 Parallel Port (ECP/EPP) !" 2 Serial Ports (16C550 Fast UART Compatible) !" 1 PS/2 Mouse Connector, 1 PS/2 Keyboard connector !" 4 Standard USB Connector (48MHz) !" 1 IrDA TX/RX Port (Optional) System BIOSSystem BIOSSystem BIOSSystem BIOS !" 2MB flash EPROM. !" Award PCI BIOS with plug and play, ACPI, STR, APM, Y2K, PC99 and DMI support !" Bootable from CD-ROM supported Green FeaturesGreen FeaturesGreen FeaturesGreen Features !" Power Management: APM 2.1 !" Additionally, with support for ACPI (Advanced Configuration and Power Interface) feature and On-Now, your system will become more wise in power management Sound System (option)Sound System (option)Sound System (option)Sound System (option) !" Creative Lab. ES1373 or CT5880 PCI 3D Audio Chip (Optional) !" 3 Audio Phone Jacks (Line out, Line in, Mic. In) (optional) !" 1 MIDI/Game port, 1 CD in, 1 Modem in. 1 Aux in. (optional) !" S/PDIF Interface support (optional) !" VT82C686A Integrated AC97 Controller, AC97 Codec (Rev: 2.1) (optional) Additional featuresAdditional featuresAdditional featuresAdditional features !" Wake-On-LAN header !" Keyboard/Mouse power on function !" Modem Ring up function !" Front USB header (optional) !" 4 Channel output capability (CT5880 only) Hardware Monitor CapabilityHardware Monitor CapabilityHardware Monitor CapabilityHardware Monitor Capability !" Internal ambient temperature sensing !" Remote thermal diode sensing for direct monitoring of processor temperature !" Power supply monitoring (+12V, VCORE, VCC, VTT) to detect levels above or below acceptable values !" SMBus interface Expansion SlotsExpansion SlotsExpansion SlotsExpansion Slots !" One AGP slot !" Three PCI slots !" One ISA slot !" One AMR slot !" One shared slot for either PCI or ISA add-in board

12 2. Features2. Features2. Features2. Features Mechanical Mechanical Mechanical Mechanical !" This motherboard complies with the ATX Form Factor specifications and has four layers with dimensions of 12” x 8” (30.5x21cm)

13 3. Installation3. Installation3. Installation3. Installation 33333333........ IIIIIIIInnnnnnnnssssssssttttttttaaaaaaaallllllllllllllllaaaaaaaattttttttiiiiiiiioooooooonnnnnnnn 3.1 Motherboard Layout & Main Parts3.1 Motherboard Layout & Main Parts3.1 Motherboard Layout & Main Parts3.1 Motherboard Layout & Main Parts FLOPPY PRIMARY IDEUSB KEYBOARD/MOUSE PRINTER COM2/COM1 DIMM2 ATX POWER PCI EXPANSION SLOT FRONT PANEL CONNECTORS POWER FAN AUX-IN GAME/MIDI AUDIO HEADERS AMR MODEM-IN CD-IN SECONDARY IDE SCSI HD WOL DIMM3 DIMM1 FRONT USB ISA S/PDIF WOR BIOS CONFIG. CHASSIS INTRUSION AGP CPU FAN VIA 686A VIA694X CPU Socket CHASSIS FAN CPU TYPE SETUP

14 3. Installation3. Installation3. Installation3. Installation Significant Parts ListSignificant Parts ListSignificant Parts ListSignificant Parts List Front Panel Connectors Infrared Connector Refer to Sec. 3.6.5 Power Switch Refer to Sec. 3.6.5 Power LED Refer to Sec. 3.6.5 Speaker Refer to Sec. 3.6.5 Reset Refer to Sec. 3.6.5 Sleep Refer to Sec. 3.6.5 HDD LED Refer to Sec. 3.6.5 Back Panel Connectors PS/2-style keyboard and mouse connectors Refer to Sec. 3.6.6 USB connectors Refer to Sec. 3.6.6 Two serials ports Refer to Sec. 3.6.6 Parallel port Refer to Sec. 3.6.6 Game Port Refer to Sec. 3.6.6 Line-Out Refer to Sec. 3.6.6 Line-In Refer to Sec. 3.6.6 MIC-In Refer to Sec. 3.6.6 Expansion Slots CPU Slot Refer to Sec. 3.3 DIMM Sockets Refer to Sec. 3.4 ISA/PCI/AGP/AMR Slots Refer to Sec. 3.5 Power/IDE/FDD Connectors IDE connectors Refer to Sec. 3.6.1-3.6.2 Power connector Refer to Sec. 3.6.4 FDD connector Refer to Sec. 3.6.3

15 3. Installation3. Installation3. Installation3. Installation Additional Connectors SCSI HD Connector Refer to Sec. 3.6.7 Chassis Intrusion Connector Refer to Sec. 3.6.7 Clear CMOS / Password Jumper Block Refer to Sec. 3.6.7 Chassis Fan Connector Refer to Sec. 3.6.7 Wake On LAN Technology Connector Refer to Sec. 3.6.7 Wake On Ring Technology Connector Refer to Sec. 3.6.7 CPU Fan Connector Refer to Sec. 3.6.7 Power Fan Connector Refer to Sec. 3.6.7 S/P-DIF Connector (Optional) Refer to Sec. 3.6.7 Telephony Connector Refer to Sec. 3.6.7 ATAPI-Style CD-ROM Connector Refer to Sec. 3.6.7 Auxiliary Line IN Connector Refer to Sec. 3.6.7

16 3. Installation3. Installation3. Installation3. Installation Precaution Before StartPrecaution Before StartPrecaution Before StartPrecaution Before Start Static Electricity Damage:Static Electricity Damage:Static Electricity Damage:Static Electricity Damage: Static electricity can easily damage your motherboard. Observing a few basic precautions can help safeguard against damage that could result in expensive repairs. Follow the simple measures below to protect your equipment from static electricity damage. 1. Keep the motherboard and other system components in their anti-static packaging until you are ready to install them. 2. Touch a grounded surface before you remove any system component from its protective anti-static packaging. Unpacking and installation should be done on a grounded, anti-static mat. The operator should be wearing an anti-static wristband, grounded at the same points as the anti-static mat. 3. After removing the motherboard from its original packaging, only place it on a grounded, anti-static surface component side up. Immediately inspect the board for damage. 4. During configuration and installation touch a grounded surface frequently to discharge any static electrical charge that may have built up in your body. The best precaution is to wear a grounded wrist strap. Avoid touching the components when handling the motherboard or an adapter card. Handle the motherboard and adapter cards either by the edges or by the adapter card case-mounting bracket. Misplaced Jumper Damage:Misplaced Jumper Damage:Misplaced Jumper Damage:Misplaced Jumper Damage: There are critical headers used for connectors or power sources. These are clearly marked separately from the jumpers listed in Motherboard Layout. Incorrect setting of jumpers and connectors may lead to damage to your motherboard. Please pay special attention not to connect these headers in wrong directions

17 3. Installation3. Installation3. Installation3. Installation 3.2 Slots And Connectors3.2 Slots And Connectors3.2 Slots And Connectors3.2 Slots And Connectors This motherboard requires jumper setting for making some change. PIN 1 PIN 1 Note: In the following pages, the triangle ▲ mark stands for pin 1 of the connectors. Slots/Connectors List J13: PCI 4 J2: Keyboard/Mouse J14: PCI 3 J4: USB1/USB2 J15: PCI 2 J9: Printer J16: PCI 1 J4: COM1 J17: AGP Slot J3: COM2 J12: AMR Slot J8: Line-In, Line-Out, MIC-In J25: Primary IDE J7: MIDI J24: Secondary IDE J6: MODEM-IN J26: Floppy J10: CD-IN J21: Front USB J11: AUX-IN JP1: CPU Speed J1: S/P-DIF J32: Clear CMOS/Password J22: ATX Power J23: Power Fan J33-J39: Front Panel Header J20: CPU Fan J19: WOL (Wake On LAN) J30: Chassis Fan J18: WOR J28: SCSI ID Connector J27: Chassis Intrusion Connector JP2: CPU Type Setup

18 3. Installation3. Installation3. Installation3. Installation 3.3 CPU (Central Processing Unit)3.3 CPU (Central Processing Unit)3.3 CPU (Central Processing Unit)3.3 CPU (Central Processing Unit) This motherboard supports an Intel socket 370 PGA family processor. To complete CPU installation, please install CPU to socket firmly as presented in sec. 3.3.1. 3.3.1 Install CPU3.3.1 Install CPU3.3.1 Install CPU3.3.1 Install CPU Please follow the below steps to install your CPU and configure the types and speed in according to the Processor Jumper Setting List. Step 1: Pull the handle bar of the socket upward to loosen the socket for insertion and removal of the CPU. Step 2: Place the CPU in the middle of the socket, orienting its beveled corner to line up with the socket’s beveled corner. Make sure the pins of the CPU fit evenly to the socket openings. Step 1 Step 2 Handling Bar

19 3. Installation3. Installation3. Installation3. Installation Step 3: Press the handle bar downward to fasten the CPU into the socket. Warning: It is O.K. that a heatsink and CPU cooling fan be used to prevent the CPU from overheating. Applying a thermal of jelly between the CPU and the heatsink/fan will further cool the CPU. 3.3.2 Set CPU Speed3.3.2 Set CPU Speed3.3.2 Set CPU Speed3.3.2 Set CPU Speed For different CPU frequency ratio, you have to configure the jumper settings for your CPU. Please refer to the following figure and tables to carefully finish it. Note: The Host Bus frequency is detected by motherboard automatically. As for some CPU with frequency fixed, you don’t have to set CPU Frequency Rate. 2 1 VIA686A VIA694X JP1

20 3. Installation3. Installation3. Installation3. Installation Now follow the below table to configure your CPU settings. JP1 CPU/BUS Ratio Pin 1&2 Pin 3&4 Pin 5&6 Pin 7&8 X3 X3.5 X4 X4.5 X5 X5.5 X6 X6.5 X7 X7.5 X8 CPU Type JP2 Intel 1-3,2-4 Cyrix 3-5,4-6

21 3. Installation3. Installation3. Installation3. Installation 3.4 System Memory (DRAM)3.4 System Memory (DRAM)3.4 System Memory (DRAM)3.4 System Memory (DRAM) 3.4.1 DIMM (Du3.4.1 DIMM (Du3.4.1 DIMM (Du3.4.1 DIMM (Dual Inline Memory Module)al Inline Memory Module)al Inline Memory Module)al Inline Memory Module) The motherboard features three 168-pin DIMM sockets. You can configure the system memory size from 8MB to 1.5GB in a variety of ways by using different combinations of the three 168-pin DIMMs. VI6869 3.43.43.43.4.2 Installation Procedure.2 Installation Procedure.2 Installation Procedure.2 Installation Procedure Step1: Make sure Pin 1 of the DIMM matches with pin 1 of the DIMM socket. Step2: Insert the DIMM module into the DIMM socket vertically. After inserting the DIMM module completely into the socket, push up on the socket latches securing the DIMM into place. If pin 1 of the DIMM module does not line up with pin 1 of the socket, the DIMM module will not be inserted correctly into the socket. Be careful not to misfit the DIMM Module into the DIMM sockets in the wrong direction. This module can be inserted into the socket only one way. To release the memory module, push both latches down and carefully rock the module forward and backward while slowly lifting it upward. DIMM3 DIMM2 DIMM1

22 3. Installation3. Installation3. Installation3. Installation 3.4.3 DIMM Module Combinations3.4.3 DIMM Module Combinations3.4.3 DIMM Module Combinations3.4.3 DIMM Module Combinations Each DIMM socket can be inserted with 8MB, 16MB, 32MB, 64MB, 128MB, 256MB, 512MB DIMM. For example, the following figure shows you one way to insert your DIMM. EmptyEmpty 32MB32MB128MB128MB64MB64MB512MB512MBDIMM 1DIMM 3Select8MB8MBEmpty 32MB 128MB64MB 512MBDIMM 28MB16MB16MB16MB256MB256MB256MB Select DIMM 1:64MB DIMM2: 16MB DIMM 3: 128MB Total 64+16+128=208 MB Select one of the 7 choices (Empty, 8MB, 16MB, 32MB, 64MB, 128MB, 256MB, 512MB) in DIMM1. Then, repeat in DIMM2 and 3 (Empty, 8MB, 16MB, 32MB, 64MB, 128MB, 256MB, 512MB) to go through your own path.

23 3. Installation3. Installation3. Installation3. Installation 3.5 Expansion Slots3.5 Expansion Slots3.5 Expansion Slots3.5 Expansion Slots ISAPCI AMRAGPVI686 694 This motherboard contains 8 expansion slots (including one shared PCI/ISA). One 16-bit ISA Bus, four 32-bit PCI expansion slots, one 32-bit AGP slot and one AMR slot are shown as above. PCI Expansion SlotsPCI Expansion SlotsPCI Expansion SlotsPCI Expansion Slots All PCI expansion slots accept PCI bus master cards and are fully supported by the PCI 2.1 specification. AMR AMR AMR AMR Expansion SlotExpansion SlotExpansion SlotExpansion Slot The Audio Modern Riser (AMR) connector which supports an industry-standard riser board and interface for both audio and modem, while also addressing specific function limitations of previous audio and modern subsystem(AMR interface specification Rev. 1.01 compliant). AGP AGP AGP AGP Expansion SlotExpansion SlotExpansion SlotExpansion Slot The Accelerated Graphics Port (AGP or A.G.P.) is a high performance interconnect targeted at 3D graphical display applications and is based on a set of performance extensions or enhancements to the PCI bus. (AGP interface specification Rev. 2.0 compliant.) Note: The motherboard supports AGP 1X/2X/4X mode. To install expansion cards, please read the expansion card’s documentation for instructions and cautions.

24 3. Installation3. Installation3. Installation3. Installation 3.6 Connectors 3.6 Connectors 3.6 Connectors 3.6 Connectors This motherboard contains IDE, floppy, power input, front panel, back panel and additional connectors. 3.6.1 Primary IDE Connector (J25, 393.6.1 Primary IDE Connector (J25, 393.6.1 Primary IDE Connector (J25, 393.6.1 Primary IDE Connector (J25, 39----pin block, Black)pin block, Black)pin block, Black)pin block, Black) This connector supports two primary channel IDE devices via a ribbon cable. When two IDE devices are installed using the primary IDE connector, make sure that the second IDE device is set to slave mode as indicated in the device’s manual. 403921403921Secondary IDEPrimary IDE VI686 694 3.6.2 Secondary IDE Connector (J24, 393.6.2 Secondary IDE Connector (J24, 393.6.2 Secondary IDE Connector (J24, 393.6.2 Secondary IDE Connector (J24, 39----pin block, White)pin block, White)pin block, White)pin block, White) This connector supports two secondary channel IDE devices as well as the 120MB Floppy drives via a ribbon cable. When two IDE devices are installed using the secondary IDE connector, make sure that the second IDE device is adjusted to slave mode as indicated in the device’s manual. Warning: When you connect a ribbon cable to these ports, you must orient the cable connector so that the PIN 1 edge of the cable is at the PIN 1 edge of the onboard connector.

25 3. Installation3. Installation3. Installation3. Installation 3.6.3 Floppy Drive Connector (J26, 333.6.3 Floppy Drive Connector (J26, 333.6.3 Floppy Drive Connector (J26, 333.6.3 Floppy Drive Connector (J26, 33----pin block)pin block)pin block)pin block) 343321 VI686 694 The FDC sub-system can control three types of floppy drives (1.2, 1.44 and 2.88MB) or compatible tape drives. The connection to the floppy drive is via a header. The floppy disk interface includes 48mA drivers and inputs on the drive interface. 3.6.4 Power Input Connector (J22, 203.6.4 Power Input Connector (J22, 203.6.4 Power Input Connector (J22, 203.6.4 Power Input Connector (J22, 20----pin block)pin block)pin block)pin block) 1112010ATX Power VI686 694 This connector supports a ATX power supply. When connecting, make sure the lock key matches the hook attached on a power supply cable. The power cord should be unplugged when you connect it.

26 3. Installation3. Installation3. Installation3. Installation 3.6.5 Front Panel Connectors (J333.6.5 Front Panel Connectors (J333.6.5 Front Panel Connectors (J333.6.5 Front Panel Connectors (J33----J39, 15J39, 15J39, 15J39, 15----pin)pin)pin)pin) Front Panel includes headers for the following seven I/O connectors: Power Switch, Power LED, Speaker, Reset, Sleep, Infrared and HDD LED. SPEAKER RESESTPOWER LED HD LEDINFRARED SLEEP POWER O27 1VIA686A VIA694X Speaker Connector (4Speaker Connector (4Speaker Connector (4Speaker Connector (4----pin)pin)pin)pin) SPEAKER PWRSPEAKER_OUTPUT27 26 24SPEAKER It is used to drive a chassis-mounted speaker if desired.

27 3. Installation3. Installation3. Installation3. Installation Reset Switch Connector (2Reset Switch Connector (2Reset Switch Connector (2Reset Switch Connector (2----pin)pin)pin)pin) RESEST23 22FRONT PANEL RESET INGROUND This connector supports the front panel case-mounted reset button. It is advised that the reset switch be used for rebooting the system in order to extend the life of the system’s power supply. Power LED (4Power LED (4Power LED (4Power LED (4----pin)pin)pin)pin) POWER LED 20 18YELLOW: SLEEPINGGREEN: RUNNING This header can be connected to an LED that will light when the computer is powered on. HHHHDD (IDE) LED Connector (4DD (IDE) LED Connector (4DD (IDE) LED Connector (4DD (IDE) LED Connector (4----pin)pin)pin)pin) HD LED 16 15 13HARD DISK LED PULL-UP TO +5V The motherboard supports one straight 4-pin header for connecting to front Panel Hard Disk activity LED indicator. Infrared (IrDA) Connector (6Infrared (IrDA) Connector (6Infrared (IrDA) Connector (6Infrared (IrDA) Connector (6----pin)pin)pin)pin) INFRARED11 10 9 8 6IR POWERIRTXGROUNDIRRX The motherboard offers an IrDA infrared header that supports third party infrared modules. The case must reserve space for the IR module if you want to use the IrDA function. This option supports wireless transmission and reception of infrared data. The module mounts in a small opening on the system case that supports this feature. The efficient distance is 100cm and the transfer rate is 115,200 bits/sec.

28 3. Installation3. Installation3. Installation3. Installation Sleep Switch (2Sleep Switch (2Sleep Switch (2Sleep Switch (2----pin)pin)pin)pin) SLEEP 4 3GROUNDSLEEP When the APM (Advanced Power Management) feature is enabled in the system BIOS and the operating system’s APM driver is loaded, the system can enter the sleep (standby) mode in one of the following ways: !" Optional front panel sleep/resume button !" Prolonged system inactivity using the BIOS inactivity timer feature. The 2-pin header supports a front panel sleep/resume switch, which must be a momentary SPST type that is normally open. Power Switch (2Power Switch (2Power Switch (2Power Switch (2----pin)pin)pin)pin) POWER ON GROUNDON/OFF SWITCH2 1 This connector supports the ATX case-mounted Power Switch, which in turn supports System Suspend function. When the BIOS sets the Power Button function to “Delay 4 sec.”, the system can be set to the suspended mode once you push the power switch for no longer then 4 seconds. If the power switch is pushed down for over 4 seconds the system will be totally Power Off. When the BIOS setting sets the Delay 4 second to “Instant-off”, then Power Switch function work as regular power switch.

29 3. Installation3. Installation3. Installation3. Installation 3.6.6 Back Panel Connectors3.6.6 Back Panel Connectors3.6.6 Back Panel Connectors3.6.6 Back Panel Connectors VIA686A VIA694X Mouse Keyboard USB2 USB1 Parallel port COM1 COM2 Game/MIDI Audio Jacks

30 3. Installation3. Installation3. Installation3. Installation PS/2 Keyboard and Mouse Ports (J2)PS/2 Keyboard and Mouse Ports (J2)PS/2 Keyboard and Mouse Ports (J2)PS/2 Keyboard and Mouse Ports (J2) The motherboard offers 1 PS/2 Keyboard and 1 PS/2 Mouse port. Universal Serial Bus (USB) Ports (J4)Universal Serial Bus (USB) Ports (J4)Universal Serial Bus (USB) Ports (J4)Universal Serial Bus (USB) Ports (J4) The motherboard has two USB connectors. USB devices provide a more convenient operating environment and improve data transferring capacity. True Plug & Play. This new bus technology will support over 127 different peripherals through a Hub. Parallel Port (PrinterParallel Port (PrinterParallel Port (PrinterParallel Port (Printer, J9, J9, J9, J9)))) The motherboard includes a parallel port (EPP/ECP compatible). The parallel port is capable of being disabled or remapped to either the secondary LPT address or the primary LPT address through BIOS if another parallel port is installed. Parallel port Mouse Keyboard USB2 USB1

31 3. Installation3. Installation3. Installation3. Installation Serial Port (COM1/COM2, J4/J3)Serial Port (COM1/COM2, J4/J3)Serial Port (COM1/COM2, J4/J3)Serial Port (COM1/COM2, J4/J3) The motherboard has two serial ports (one on rare panel, one on board). The electrical characteristics are compliant with the EIA-232-D Serial Communications Specifications. The serial ports may be remapped over other installable serial ports or disabled through the BIOS. COM1 This product integrate the AGP function via a VGA port beside the COM1. The Accelerated Graphics Port (AGP or A.G.P.) is a high performance interconnect targeted at 3D graphical display applications. GAME / MIDI Port (J7) (optional)GAME / MIDI Port (J7) (optional)GAME / MIDI Port (J7) (optional)GAME / MIDI Port (J7) (optional) The motherboard integrates a Game/MIDI port. This port can let you pulg a joystick or MIDI device. Audio Port ( LineAudio Port ( LineAudio Port ( LineAudio Port ( Line----in, Linein, Linein, Linein, Line----out, MICout, MICout, MICout, MIC----in)in)in)in) (J8) (optional) (J8) (optional) (J8) (optional) (J8) (optional) The motherboard also provides external sound system through a user accessible stereo jack connector soldered to the PWA.This jack allow the connection of self-amplified speakers, Line-in voice input and MIC-in voice input. COM2 Game/MIDI Line-out, Line-in, MIC-in

32 3. Installation3. Installation3. Installation3. Installation 3.6.7 Additi3.6.7 Additi3.6.7 Additi3.6.7 Additional Connectorsonal Connectorsonal Connectorsonal Connectors MODEM-IN CD-INVIA 686A VIA694XCHASSIS-FAN CPU-FAN POWER-FAN S/P-DIF AUX-IN S/PS/PS/PS/P----DIF(J9, 2DIF(J9, 2DIF(J9, 2DIF(J9, 2----pin)pin)pin)pin) This connector is the digital link between the motherboard and your audio devices such as CD player, or DAT recorder. It allows the digital transmission of audio data in SPDIF (Sony/Philips Digital Interface) Format. MODEMMODEMMODEMMODEM----IN Header (J8, 4IN Header (J8, 4IN Header (J8, 4IN Header (J8, 4----pin, Green)pin, Green)pin, Green)pin, Green) A 1x4 pin ATAPI style connector is available for connecting the monaural audio signals of an internal telephony device to the audio subsystem. A monaural audio-in and audio-out signal interface is necessary for telephony applications such as speakerphones, fax modems, and answering machines.

33 3. Installation3. Installation3. Installation3. Installation CDCDCDCD----IN Header (J10, 4IN Header (J10, 4IN Header (J10, 4IN Header (J10, 4----pin, Black)pin, Black)pin, Black)pin, Black) A connector is available for audio input from CD-ROM drives. AUXAUXAUXAUX----IN Header (J11, 4IN Header (J11, 4IN Header (J11, 4IN Header (J11, 4----pin, White)pin, White)pin, White)pin, White) It allows access to the AUX-IN connector for audio input from AUX devices. CPU Fan (J20, 3CPU Fan (J20, 3CPU Fan (J20, 3CPU Fan (J20, 3----pin)pin)pin)pin) Your CPU may have an attached heatsink and Fan; this connector is the power source for the CPU Fan. Power Fan (J23, 3Power Fan (J23, 3Power Fan (J23, 3Power Fan (J23, 3----pin)pin)pin)pin) The power fan connector provides +12V DC for system power supply. CCCChassis Fan (J30, 3hassis Fan (J30, 3hassis Fan (J30, 3hassis Fan (J30, 3----pin)pin)pin)pin) This header can supply power for Chassis fan that may be mounted inside your case to cool down your system components. If your chassis have a Chassis Fan, this header will support. VIA686A VIA694XSCSI HD CHASSIS INSTRUSIONBIOS CONFIG WOL WOR FRONT USB

34 3. Installation3. Installation3. Installation3. Installation WOL (Wake On LAN, J19WOL (Wake On LAN, J19WOL (Wake On LAN, J19WOL (Wake On LAN, J19) ) ) ) This header is used for remote wakeup of the computer through a network. WOL requires a PCI add-in network interface card (NIC) with remote wakeup capabilities. The remote wakeup header on the NIC must be connected to the onboard Wake on LAN header. For Wake on LAN, the 5-V standby line for the power supply must be capable of delivering 5V±5% at 720mA. WOR (Wake On Ring , J18) WOR (Wake On Ring , J18) WOR (Wake On Ring , J18) WOR (Wake On Ring , J18) This header is used for resuming from either the APM sleep mode or the ACPI S1 state. It requires only one call to access the computer. In addition, it detects incoming call similarly for external and internal modems. It also requires modem interrupt be unmasked for correct operation. SCSI HD (J28)SCSI HD (J28)SCSI HD (J28)SCSI HD (J28) The SCSI HD connector is a 1x2-pin connector that allows an add-in SCSI controller to use the same LED as the onboard IDE controller. This connector can be connected to the LED output of the add-in controller card. The LED will indicate when data is being read or written using the add-in controller. Chassis Intrusion (J27)Chassis Intrusion (J27)Chassis Intrusion (J27)Chassis Intrusion (J27) The board supports a chassis security feature that detects if the chassis cover is removed and sounds an alarm (through the onboard speaker or PC chassis speaker, if either is present). For the chassis intrusion circuit to function, the chassis’ power supply must be connected to AC power. The security feature uses a mechanical switch on the chassis that attaches to the chassis intrusion detect connector. The mechanical switch is closed for normal computer operation. BIOS Config. (J32, 4BIOS Config. (J32, 4BIOS Config. (J32, 4BIOS Config. (J32, 4----pin)pin)pin)pin) PinPinPinPin FunctionFunctionFunctionFunction DescriptionDescriptionDescriptionDescription 1-2 Recovery The BIOS will recover the BIOS configuration. A recovery disk is needed. 2-3 Normal The BIOS uses current configuration setting and password for booting. 3-4 Clear CMOS/Password The BIOS clear the CMOS /Password data and reload the default settings

35 3. Installation3. Installation3. Installation3. Installation Front USB (J31, 9Front USB (J31, 9Front USB (J31, 9Front USB (J31, 9----pin)pin)pin)pin) Front USB connector is provided as another choice for using USB devices. PinPinPinPin SignalSignalSignalSignal PinPinPinPin SignalSignalSignalSignal 1 VCC 2 VCC 3 GROUND 4 NC 5 USBP2+ 6 USBP3+ 7 USBP2- 8 USBP3- 13579246810 9 GROUND 10 NC

36 3. Installation3. Installation3. Installation3. Installation Ready To TurnReady To TurnReady To TurnReady To Turn On Power On Power On Power On Power Check AgainCheck AgainCheck AgainCheck Again 1. Is the CPU installed exactly and firmly into the socket (Sec. 3.3)? 2. Are all the DRAM modules installed properly (Sec. 3.4)? 3. Did you insert the expansion card (VGA, Sound… etc.) already (Sec. 3.5)? Are you sure that all the connectors (described in Sec 3.6) have been connected to their variable devices (Sec. 3.6)? Yes, I have checked and assured the above steps!Yes, I have checked and assured the above steps!Yes, I have checked and assured the above steps!Yes, I have checked and assured the above steps! Now get ready to turn on your device by following the steps below. 1. Mount your motherboard to the chassis frame and close the case cover. 2. Switch off all power. 3. Connect the power supply cord into inlet of the system case. 4. Connect the power supply cord into an outlet of power supply. 5. Connect Monitor signal cable to the system VGA port and the monitor power cord to power outlet. 6. Now turn on the monitor and system power. After Power on, the power LED on the front panel of the system case will light. For ATX power supplies, the system LED will light when the ATX power switch is pressed. The system will then do a power-on tests items by item, and additional messages will appear on screen. If the screen blinks or the test stops more than 30 seconds, the system may have failed the power-on test. If so, please recheck the above steps or call your retailer for assistance. If the power-on test goes well, hold down <DEL> button on the keyboard to enter BIOS Setup. Next, follow the instructions in the next chapter, BIOS SETUP.

37 4. BIOS Setup4. BIOS Setup4. BIOS Setup4. BIOS Setup 44444444........ BBBBBBBBIIIIIIIIOOOOOOOOSSSSSSSS SSSSSSSSeeeeeeeettttttttuuuuuuuupppppppp The motherboard uses AWARD BIOS, which is stored in a Flash EEPROM and can be upgraded by a floppy disk-based program. The BIOS has a built-in Setup Program that allows users to modify the basic system configuration settings. The settings are then stored in a dedicated battery-backed memory, called CMOS RAM that retains the information when the power is turned off. The BIOS provides critical low-level support for the system’s central processing, memory and I/O subsystems. The AWARD BIOS has been customized by adding important, nonstandard, features such as virus and password protection, power management, and detailed fine-tuning of the chipset which it controls the system. The remainder of this manual is intended to guide you through the process of configuring your system using the BIOS Setup. 4.1 BIOS Setup4.1 BIOS Setup4.1 BIOS Setup4.1 BIOS Setup The AWARD BIOS is immediately activated when you first turn on the computer. The BIOS reads system configuration information in CMOS RAM and begins the process of checking the system and configuring it through the Power-On-Self-Test (POST). When these preliminaries are finished, the BIOS seek an operation system on the data storage devices (hard drive, floppy drive, etc.). The BIOS launches the operating system and hands over control of system operation to it. To start Setup, press the <Del> key during boot-up before or while a message similar to this appears briefly at the bottom of the screen during the POST: Press <DEL> key if you want to enter SETUP If the above message disappears before you have responded and you still wish to enter Setup, reboot the system to try again by pressing the “RESET” button on the system case. You may also restart by simultaneously pressing the <CTRL>, <ALT> and <DEL> keys.

38 4. BIOS Setup4. BIOS Setup4. BIOS Setup4. BIOS Setup 4.1.1 Setup Keys4.1.1 Setup Keys4.1.1 Setup Keys4.1.1 Setup Keys The keys below help you navigate in Setup. <↑> , <↓> Move to previous or next item. <←> , <→> Move to the item in the left or right hand. <ESC> <ESC> Main Menu – Quit and not save changes into CMOS. Other Pages -- Exit current page and return to Main Menu. <PgUp> / <+> Increase the numeric value or make changes. <PgDn> / <−> Decrease the numeric value or make changes. <F1> General help, only for Status Page Setup Menu and Option Page Setup Menu. <F2> Change color from total 16 colors. Press <F2> to select color forward, Press <Shift> and <F2> to select color backward. <F10> Save all the CMOS changes, only for Main Menu . 4.1.2 Getting Help4.1.2 Getting Help4.1.2 Getting Help4.1.2 Getting Help Press <F1> key to pop up a small help window that describes the appropriate keys to use, and the possible selections for each highlighted item. To exit the Help Window press <ESC> or the <F1> key again. 4.1.3 In Case of Prob4.1.3 In Case of Prob4.1.3 In Case of Prob4.1.3 In Case of Problemslemslemslems If after making and saving system changes with Setup, you discover that your computer no longer is able to boot, the Award BIOS supports an override to the CMOS settings that resets your system to its default configuration. The best advice is to alter only settings that you thoroughly understand. In particular, do not change settings in the Chipset screen without a good reason. BCM Advanced Research Inc. or your system manufacturer for the best performance and reliability has carefully chosen the Chipset defaults. Even a seemingly small change to the Chipset setup may cause the system to become unstable.

39 4. BIOS Setup4. BIOS Setup4. BIOS Setup4. BIOS Setup 4.2 Main Setup Menu4.2 Main Setup Menu4.2 Main Setup Menu4.2 Main Setup Menu When you enter the Award BIOS CMOS Setup Utility, a Main Menu (Figure 1) appears on the screen. The Main Menu allows you to select from several Setup functions and two exit choices. Use the arrow keys to select among the items and press <ENTER> key to accept and enter the sub-menu. Figure 1: Main Menu Standard CMOS Features Options in the original PC AT-compatible BIOS. Advanced BIOS Features Award enhanced BIOS options. Advanced Chipset Features Options specific to your system chipset. Integrated Peripherals I/O subsystems that depend on the integrated peripherals controller in your system. Power Management Setup Advanced Power Management (APM) options. PnP/PCI Configuration Plug and Play standard and PCI Local Bus configuration options. PC Health Status Display the temperature of your CPU and system. Frequency/Voltage Control Display the fan speed and voltage for your system. Load Setup Defaults Setup defaults are factory settings for optimal performance system operations. Set User Password Change, set, or disable a user password. The user password generally allows only power-on access. Save & Exit Setup Save settings in nonvolatile CMOS RAM and exit Setup. Exit Without Saving Abandon all changes and exit Setup.

40 4. BIOS Setup4. BIOS Setup4. BIOS Setup4. BIOS Setup 4.3 Standard CMOS Features Menu4.3 Standard CMOS Features Menu4.3 Standard CMOS Features Menu4.3 Standard CMOS Features Menu In the Standard CMOS Menu (Figure 2) you can set the system clock and calendar, record disk drive parameters and the video subsystem type, and select the type of errors that stop the BIOS POST. Figure 2: Standard CMOS Setup 4.3.1 Date4.3.1 Date4.3.1 Date4.3.1 Date The BIOS determines the day of the week from the other date information. This field is for information only. Press the left or right arrow key to move to the desired field (date, month, year). Press <PgUp> or <PgDn> key to increment the setting, or type the desired value into the field. 4.3.2 Time4.3.2 Time4.3.2 Time4.3.2 Time The time format is based on the 24-hour military-time clock. For example, 1 p.m. is 13:00:00. Press the left or right arrow key to move to the desired field. Press the <PgUp> or <PgDn> key to increment the setting, or type the desired value into the field.

41 4. BIOS Setup4. BIOS Setup4. BIOS Setup4. BIOS Setup 4.3.3 Hard Disks4.3.3 Hard Disks4.3.3 Hard Disks4.3.3 Hard Disks The BIOS supports up to four IDE drives. This section does not show information about other IDE devices, such as a CD-ROM drive, or about other hard drive types, such as SCSI drives. NOTE: We recommend that you select type AUTO for all drives. The BIOS can automatically detect the specifications and optimal operating mode of almost all IDE hard drives. When you select type AUTO for a hard drive, the BIOS detect its specifications during POST, every time the system boots. If you do not want to select drive type AUTO, other methods of selecting the drive type are available: 1. Match the specifications of your installed IDE hard drive(s) with the preprogrammed values for drive types 1 through 45. 2. Select USER and enter values into each drive parameter field. 3. Use the IDE HDD AUTO DECTECTION function in Setup. Here is a brief explanation of drive specifications: !" Type: The BIOS contains a table of pre-defined drive types. Each defined drive type has a specified number of cylinders, number of heads, write precompensation factor, landing zone, and number of sectors, Drives whose specifications do not accommodate any pre-defined type are classified as type USER. !" Size: Disk drive capacity (approximate). Note that this size is usually slightly greater than the size of a formatted disk given by a disk-checking program. !" Cyls: Number of cylinders !" Head: Number of heads !" Precomp: Write precompensation cylinder !" Landz: Landing zone !" Sector: Number of sectors !" Mode: Auto, Normal, large, or LBA !" Auto: The BIOS automatically determines the optimal mode. !" Normal: Maximum number of cylinders, heads, and sectors supported are 1024, 16 and 63. !" Large: For drives that do not support LBA and have more than 1024 cylinders. !" LBA (Logical Block Addressing): During drive accesses, the IDE controller transforms the data address described by sector, head, and cylinder number into a physical block address, significantly improving data transfer rates. For drives with greater than 1024 cylinders.

42 4. BIOS Setup4. BIOS Setup4. BIOS Setup4. BIOS Setup 4.3.4 Drive A/B type4.3.4 Drive A/B type4.3.4 Drive A/B type4.3.4 Drive A/B type Select the correct specifications for the diskette drive(s) installed in the computer. None No diskette drive installed. 360K, 5.25 in 5-1/4 inch AT-type standard drive; 360 kilobyte capacity. 1.2M, 5.25 in 5-1/4 inch AT-type high-density drive; 1.2 megabyte capacity. 720K, 3.5 in 3-1/2 inch double-sided drive; 720 kilobyte capacity. 1.44M, 3.5 in 3-1/2 inch double-sided drive; 1.44 megabyte capacity. 2.88M, 3.5 in 3-1/2 inch double-sided drive; 2.88 megabyte capacity. 4.3.5 4.3.5 4.3.5 4.3.5 VideoVideoVideoVideo Select the type of primary video subsystem in your computer. The BIOS usually detects the correct video type automatically. The BIOS supports a secondary video subsystem, but you do not select it in Setup. EGA/VGA Enhanced Graphics Adapter/Video Graphics Array. For EGA, VGA, SEGA, SVGA or PGA monitor adapters. CGA 40 Color Graphics Adapter, power up in 40 column mode. CGA 80 Color Graphics Adapter, power up in 80 column mode. MONO Monochrome adapter, includes high resolution monochrome adapters.

43 4. BIOS Setup4. BIOS Setup4. BIOS Setup4. BIOS Setup 4.3.6 4.3.6 4.3.6 4.3.6 Halt onHalt onHalt onHalt on During the power-on self-test (POST), the computer stops if the BIOS detect a hardware error. You can tell the BIOS to ignore certain errors during POST and continue the boot-up process. Below are the selections: No errors POST does not stop for any errors. All errors If the BIOS detect any non-fatal error, POST stops and prompts you to take corrective action. All, But Keyboard POST does not stop for a keyboard error, but stops for all other errors. All, But Diskette POST does not stop for diskette drive errors, but stops for all other errors. All, But Disk/Key POST does not stop for a keyboard or disk error, but stops for all other errors. 4.3.7 Memory4.3.7 Memory4.3.7 Memory4.3.7 Memory You cannot change any values in the Memory fields; they are only for your information. The fields show the total installed random access memory (RAM) and amounts allocated to base memory, extended memory, and other (high) memory. RAM is counted in kilobytes (KB: 1,024 bytes) and megabytes (MB: 1,024 KB). RAM is the computer's working memory, where the computer stores programs and data currently being used, so they are accessible to the CPU. Modern personal computers may contain up to 64 MB, 128 MB, or more. Base Memory Typically 640 KB. Also called conventional memory. The DOS operating system and conventional applications use this area. Extended Memory Above the 1-MB boundary. Early IBM personal computers could not use memory above 1 MB, but current PCs and their software can use extended memory. Total Memory System total memory is the sum of base memory, extended memory, and other memory.

44 4. BIOS Setup4. BIOS Setup4. BIOS Setup4. BIOS Setup 4.4 Advanced BIOS Features Menu4.4 Advanced BIOS Features Menu4.4 Advanced BIOS Features Menu4.4 Advanced BIOS Features Menu These screens (Figure 3.1 and 3.2) contain industry-standard options additional to the core PC AT BIOS. This section describes all fields offered by Award Software in this screen. Some fields may vary from those in your Setup program. Your system board designer may omit or modify some fields. Figure 3.1: Standard CMOS Features Menu Page 1 Figure 3.2: Standard CMOS Features Menu Page 2

45 4. BIOS Setup4. BIOS Setup4. BIOS Setup4. BIOS Setup 4.4.1 Virus Warning4.4.1 Virus Warning4.4.1 Virus Warning4.4.1 Virus Warning When enabled, you receive a warning message if a program (specifically a virus) attempts to write to the boot sector or the partition table of the hard disk drive. You should then run an anti-virus program. Keep in mind that this feature protects only the boot sector, not the entire hard drive. NOTE: Many disk diagnostic programs that access the boot sector table can trigger the virus-warning message. If you plan to run such a program, we recommend that you first disable the virus warning. 4.4.2 External Cache4.4.2 External Cache4.4.2 External Cache4.4.2 External Cache Cache memory is an additional memory that is much faster than conventional DRAM (system memory). When the CPU requests data, the system transfers the requested data from the main DRAM into cache memory, for even faster access by the CPU. The External Cache field may not appear if your system does not have external cache memory. 4.4.3 CPU L2 Cache ECC Checking4.4.3 CPU L2 Cache ECC Checking4.4.3 CPU L2 Cache ECC Checking4.4.3 CPU L2 Cache ECC Checking Select Enabled to allow CPU L2 Cache ECC Checking function. 4.4.4 Processor Number Feature4.4.4 Processor Number Feature4.4.4 Processor Number Feature4.4.4 Processor Number Feature This feature is to display your processor information on the boot-up, reveal the same information on the system info under Windows. The default is Disabled. 4.4.5 4.4.5 4.4.5 4.4.5 Quick Power On Self TestQuick Power On Self TestQuick Power On Self TestQuick Power On Self Test This allows you to enable or disable long system self test when power on. 4.4.6 First Boot Device4.4.6 First Boot Device4.4.6 First Boot Device4.4.6 First Boot Device This option sets the type of device for the first boot drives that the AMIBIOS attempts to boot from after AMIBIOS Post completes. 4.4.7 Second Boot Device4.4.7 Second Boot Device4.4.7 Second Boot Device4.4.7 Second Boot Device This option sets the type of device for the second boot drives that the AMIBIOS attempts to boot from after AMIBIOS Post completes. 4.4.8 Third Boot Device4.4.8 Third Boot Device4.4.8 Third Boot Device4.4.8 Third Boot Device This option sets the type of device for the third boot drives that the AMIBIOS attempts to boot from after AMIBIOS Post completes.

46 4. BIOS Setup4. BIOS Setup4. BIOS Setup4. BIOS Setup 4.4.9 Boot Other Device4.4.9 Boot Other Device4.4.9 Boot Other Device4.4.9 Boot Other Device This option allows you to boot other device. 4.4.10 4.4.10 4.4.10 4.4.10 Swap Floppy DriveSwap Floppy DriveSwap Floppy DriveSwap Floppy Drive This field is effective only in systems with two floppy drives. Selecting Enabled assigns physical drive B to logical drive A, and physical drive A to logical drive B. 4.4.11 Boot Up Floppy Seek4.4.11 Boot Up Floppy Seek4.4.11 Boot Up Floppy Seek4.4.11 Boot Up Floppy Seek When Enabled, the BIOS tests (seeks) floppy drives to determine whether they have 40 or 80 tracks. Only 360-KB floppy drives have 40 tracks; drives with 720 KB, 1.2 MB, and 1.44 MB capacity all have 80 tracks. Because very few modern PCs have 40-track floppy drives, we recommend that you set this field to Disabled to save time. 4.4.12 Boot Up NumLock Status4.4.12 Boot Up NumLock Status4.4.12 Boot Up NumLock Status4.4.12 Boot Up NumLock Status Toggle between On or Off to control the state of the NumLock key when the system boots. When toggled on, the numeric keypad generates numbers instead of controlling cursor operations. 4.4.13 Gate A20 Option4.4.13 Gate A20 Option4.4.13 Gate A20 Option4.4.13 Gate A20 Option This entry allows you to select how the gate A20 is handled. The gate A20 is a device used to address memory above 1 megabyte. Initially, the gate A20 was handled via a pin on the keyboard. Today, while keyboards still support this function, it is more common and much faster that the system chipset supports it. 4.4.14 Typematic Rate Setting4.4.14 Typematic Rate Setting4.4.14 Typematic Rate Setting4.4.14 Typematic Rate Setting When Disabled, the following two items (Typematic Rate and Typematic Delay) are irrelevant. Keystrokes repeat at a rate determined by the keyboard controller in your system. When Enabled, you can select a typematic rate and typematic delay. 4.4.15 Typematic Rate (Chars/Sec)4.4.15 Typematic Rate (Chars/Sec)4.4.15 Typematic Rate (Chars/Sec)4.4.15 Typematic Rate (Chars/Sec) When the typematic rate setting is enabled, you can select a typematic rate (the rate at which character repeats when you hold down a key) of 6, 8, 10, 12, 15, 20, 24, or 30 characters per second. 4.4.16 Typematic Delay (Msec)4.4.16 Typematic Delay (Msec)4.4.16 Typematic Delay (Msec)4.4.16 Typematic Delay (Msec) When the typematic rate setting is enabled, you can select a typematic delay (the delay before keystrokes begin to repeat) of 250, 500, 750 or 1000 milliseconds.

47 4. BIOS Setup4. BIOS Setup4. BIOS Setup4. BIOS Setup 4.4.17 Security Option4.4.17 Security Option4.4.17 Security Option4.4.17 Security Option If you have set a password, select whether the password is required every time the System boots, or only when you enter Setup. 4.4.18 OS Select for DRAM > 64MB4.4.18 OS Select for DRAM > 64MB4.4.18 OS Select for DRAM > 64MB4.4.18 OS Select for DRAM > 64MB Select OS/2 only if you are running OS/2 operating system with greater than 64MB of RAM on your system. 4.4.19 Report No FDD For WIN 954.4.19 Report No FDD For WIN 954.4.19 Report No FDD For WIN 954.4.19 Report No FDD For WIN 95 Select Yes to let Windows 95 to know whether FDD is present or not. Leave it on default setting, which is Yes. 4.4.20 Video BIOS Shadow4.4.20 Video BIOS Shadow4.4.20 Video BIOS Shadow4.4.20 Video BIOS Shadow This field allows you to change the video BIOS location from ROM to RAM. Relocating to RAM enhances system performance, as information access is faster than the ROM. 4.4.21 C80004.4.21 C80004.4.21 C80004.4.21 C8000----CBFFF to DC000CBFFF to DC000CBFFF to DC000CBFFF to DC000----DFFFFDFFFFDFFFFDFFFF These fields are used for shadowing other expansion card ROMs. If you install other expansion cards with ROMs on them, you will need to know which addresses the ROMs use to shadow them specifically. Shadowing a ROM reduces the memory available between 640KB and 102KB by the amount used for this purpose.

48 4. BIOS Setup4. BIOS Setup4. BIOS Setup4. BIOS Setup 4.5 Advanced Chipset Features Menu4.5 Advanced Chipset Features Menu4.5 Advanced Chipset Features Menu4.5 Advanced Chipset Features Menu Figure 4.1: Advanced Chipset Features Menu Page 1 Figure 4.2: Advanced Chipset Features Menu Page 2 4.5.1 SDRAM Cycle Length4.5.1 SDRAM Cycle Length4.5.1 SDRAM Cycle Length4.5.1 SDRAM Cycle Length The choices are, 2 and 3 (Default). This feature appears only when SDRAM DIMMs is installed (BIOS auto detection). If the CAS latency of your SDRAM DIMM is 2, set at 2 to enhance the system performance. If the CAS latency of your SDRAM DIMM is 3, stay with the default setting, 3.

49 4. BIOS Setup4. BIOS Setup4. BIOS Setup4. BIOS Setup 4.5.2 DRAM Frequency4.5.2 DRAM Frequency4.5.2 DRAM Frequency4.5.2 DRAM Frequency This is to select your SDRAM clock, the choices are: Host CLK, 66MHz, 100MHz, and 133MHz. Warning: Please select correct SDRAM clock setting. If your system hung due to incorrect setting, reset your computer. 4.5.3 Memory Hole4.5.3 Memory Hole4.5.3 Memory Hole4.5.3 Memory Hole You can reserve this area of system memory for ISA adapter ROM. When this area is reserved, it cannot be cached. The user information of peripherals that need to use this area of system memory usually discusses their memory requirements. 4.5.4 System BIOS Cacheable4.5.4 System BIOS Cacheable4.5.4 System BIOS Cacheable4.5.4 System BIOS Cacheable Select Enabled allows caching of the system BIOS ROM at F0000h-FFFFFh, resulting in better system performance. However, if any program writes to this memory area, a system error may result. 4.5.5 Video RAM Cacheable4.5.5 Video RAM Cacheable4.5.5 Video RAM Cacheable4.5.5 Video RAM Cacheable Select Enabled allows caching of the Video RAM, resulting in better system performance. However, if any program writes to this memory area, a system error may result. 4.5.6 AGP Aperture Size4.5.6 AGP Aperture Size4.5.6 AGP Aperture Size4.5.6 AGP Aperture Size Select the size of the Accelerated Graphics Port (AGP) aperture. The aperture is a portion of the PCI memory address range dedicated for graphics memory address space. Those cycles that hit the aperture range are forwarded to the AGP without any transaction. See www.agpforum.org for AGP information. 4.5.7 AGP4.5.7 AGP4.5.7 AGP4.5.7 AGP----4X Mode4X Mode4X Mode4X Mode Select Enabled allows the maximum bus utilization to AGP-4X mode transfers. 4.5.8 AGP Driving Control4.5.8 AGP Driving Control4.5.8 AGP Driving Control4.5.8 AGP Driving Control This item allows you to adjust the AGP driving force. Choose Manual to key in an AGP Driving Value in the next selection. This field is recommended to set in Auto to avoid any error in your system. 4.5.9 AGP Driving Value4.5.9 AGP Driving Value4.5.9 AGP Driving Value4.5.9 AGP Driving Value This item allows you to adjust the AGP driving force. The choices are: Min = 00 to Max = FF.

50 4. BIOS Setup4. BIOS Setup4. BIOS Setup4. BIOS Setup 4.5.10 OnChip4.5.10 OnChip4.5.10 OnChip4.5.10 OnChip USB USB USB USB Select Enabled if your system contains a Universal Serial Bus (USB) controller. The choices are: Enabled, and Disabled. 4.5.11 OnChip FrontSide USB4.5.11 OnChip FrontSide USB4.5.11 OnChip FrontSide USB4.5.11 OnChip FrontSide USB Select Enabled if your system contains a FrontSide Universal Serial Bus (USB) controller. The choices are: Enabled, and Disabled. 4.5.12 USB Keyboard Support4.5.12 USB Keyboard Support4.5.12 USB Keyboard Support4.5.12 USB Keyboard Support Select Enabled if your system contains a Universal Serial Bus (USB) controller and you have a USB keyboard. 4.5.13 OnChip Sound4.5.13 OnChip Sound4.5.13 OnChip Sound4.5.13 OnChip Sound Select Enabled if your system contains an onboard audio circuitry and desired to use it. The choices are: Enabled, and Disabled. 4.5.14 OnChip Modem4.5.14 OnChip Modem4.5.14 OnChip Modem4.5.14 OnChip Modem Select Enabled if your system contains software modem controller. The choices are: Enabled, and Disabled. 4.5.15 CPU to PCI Write Buffer4.5.15 CPU to PCI Write Buffer4.5.15 CPU to PCI Write Buffer4.5.15 CPU to PCI Write Buffer When this field is enabled, writes from the CPU to the PCI bus is buffered, to compensate for the speed differences between the CPU and the PCI bus. When disabled, the writes are not buffered and the CPU must wait until the write is complete before starting another write cycle. 4.5.16 PCI Dyna4.5.16 PCI Dyna4.5.16 PCI Dyna4.5.16 PCI Dynamic Burstingmic Burstingmic Burstingmic Bursting When enabled, every write transaction goes to the write buffer. Burstable transactions then burst on the PCI bus and non-burstable transactions don’t. The choices are: Enabled, and Disabled. 4.5.17 Master 0 WS Write4.5.17 Master 0 WS Write4.5.17 Master 0 WS Write4.5.17 Master 0 WS Write When enabled, writes to the PCI bus are executed with zero wait states. The choices are: Enabled, and Disabled.

51 4. BIOS Setup4. BIOS Setup4. BIOS Setup4. BIOS Setup 4.5.18 PCI Delay Transaction4.5.18 PCI Delay Transaction4.5.18 PCI Delay Transaction4.5.18 PCI Delay Transaction The chipset has an embedded 32-bit posted write buffer to support delay transactions cycles. Select Enabled to support compliance with PCI specification version 2.1. The choices are: Enabled, and Disabled. 4.5.19 PCI#2 Access #1 Retry4.5.19 PCI#2 Access #1 Retry4.5.19 PCI#2 Access #1 Retry4.5.19 PCI#2 Access #1 Retry When the first time PCI#2 (AGP bus) accesses to PCI#1 (PCI bus) has an error occurred, system will try again automatically. The choices are: Enabled, and Disabled. 4.5.20 AGP Master 1 WS Write4.5.20 AGP Master 1 WS Write4.5.20 AGP Master 1 WS Write4.5.20 AGP Master 1 WS Write When enabled, writes to the AGP (Accelerated Graphics Port) is executed with one wait state. The choices: Enabled, and Disabled. 4.5.21 AGP Master 1 WS Read4.5.21 AGP Master 1 WS Read4.5.21 AGP Master 1 WS Read4.5.21 AGP Master 1 WS Read When enabled, reads to the AGP (Accelerated Graphics Port) is executed with one wait state. The choices are: Enabled and Disabled. 4.5.22 Memory Parity/ECC Check4.5.22 Memory Parity/ECC Check4.5.22 Memory Parity/ECC Check4.5.22 Memory Parity/ECC Check Select Disabled to ignore the parity or ECC (Error Checking and Correction) for standard memory modules. By using genuine parity or ECC memory modules, this option can be enabled. The default is Disabled.

52 4. BIOS Setup4. BIOS Setup4. BIOS Setup4. BIOS Setup 4.6 Integrated Peripherals4.6 Integrated Peripherals4.6 Integrated Peripherals4.6 Integrated Peripherals Figure 5.1: Integrated Peripherals Menu Page 1 Figure 5.2: Integrated Peripherals Menu Page 2 4.6.1 OnChip IDE Channel 04.6.1 OnChip IDE Channel 04.6.1 OnChip IDE Channel 04.6.1 OnChip IDE Channel 0 The chipset contains a PCI IDE interface with support for two IDE channels. Select Enabled to activate the primary IDE interface. Select Disabled to deactivate this interface. The choices are: Enabled, and Disabled.

53 4. BIOS Setup4. BIOS Setup4. BIOS Setup4. BIOS Setup 4.6.2 4.6.2 4.6.2 4.6.2 OnChip IDE Channel 1OnChip IDE Channel 1OnChip IDE Channel 1OnChip IDE Channel 1 The chipset contains a PCI IDE interface with support for two IDE channels. Select Enabled to activate the secondary IDE interface. Select Disabled to deactivate this interface. The choices are: Enabled, and Disabled. 4.6.3 IDE Prefetch Mode4.6.3 IDE Prefetch Mode4.6.3 IDE Prefetch Mode4.6.3 IDE Prefetch Mode The onboard IDE drive interface supports IDE prefetching for faster drive accesses. If you install a primary and/or secondary add-in IDE interface, set this field to Disabled if the interface does not support prefetching. The choices are: Enabled, and Disabled. 4.6.4 IDE Primary/Secondary Master/Slave PIO4.6.4 IDE Primary/Secondary Master/Slave PIO4.6.4 IDE Primary/Secondary Master/Slave PIO4.6.4 IDE Primary/Secondary Master/Slave PIO The four IDE PIO (Programmed Input / Output) fields let you set a PIO mode (0-4) for each of the four IDE devices that the onboard IDE interface supports. 4.6.5 IDE Primary/Secondary Master/Slave UDMA4.6.5 IDE Primary/Secondary Master/Slave UDMA4.6.5 IDE Primary/Secondary Master/Slave UDMA4.6.5 IDE Primary/Secondary Master/Slave UDMA Ultra DMA-33/66 implementation is possible only if your IDE hard drive supports it and the operating environment includes a DMA driver (Windows 95 OSR2 or a third-party IDE bus master driver). If your hard drive and your system software both support Ultra DMA-33/66, select Auto to enable BIOS support. The choices are: Auto, and Disabled. 4.6.6 4.6.6 4.6.6 4.6.6 Init Display FirstInit Display FirstInit Display FirstInit Display First This item allows you to decide to active whether PCI Slot or AGP first. The choices are: PCI Slot, and AGP. 4.6.7 IDE HDD Block Mode4.6.7 IDE HDD Block Mode4.6.7 IDE HDD Block Mode4.6.7 IDE HDD Block Mode Block mode is also called block transfer, multiple commands, or multiple sector read/write. If your IDE hard drive supports block mode (most new drives do), select Enabled for automatic detection of the optimal number of block read/writes per sector the drive can support. The choices are: Enabled, and Disabled. 4.6.84.6.84.6.84.6.8 Onboard FDD Controller Onboard FDD Controller Onboard FDD Controller Onboard FDD Controller Select Enabled if your system has a floppy disk controller (FDC) installed on the system board and you wish to use it. If you install add-in FDC or the system has no floppy drive, select Disabled in this field. The choices are: Enabled, and Disabled.

54 4. BIOS Setup4. BIOS Setup4. BIOS Setup4. BIOS Setup 4.4.4.4.6.9 6.9 6.9 6.9 Onboard Serial Port 1/Port 2Onboard Serial Port 1/Port 2Onboard Serial Port 1/Port 2Onboard Serial Port 1/Port 2 This item allows you to determine access onboard serial port 1/port 2 controller with which I/O address. The choices are: 3F8/IRQ4, 2E8/IRQ3, 3E8/IRQ4, 2F8/IRQ3, Disabled, and Auto. 4.6.10 UART 2 Mode4.6.10 UART 2 Mode4.6.10 UART 2 Mode4.6.10 UART 2 Mode This item allows you to select which mode for the Onboard Serial Port 2. The choices are: Standard, HPSIR, and ASKIR. 4.6.11 IR Function Duplex4.6.11 IR Function Duplex4.6.11 IR Function Duplex4.6.11 IR Function Duplex This item allows you to select the IR half/full duplex function. The choices are: Half, and Full. 4.6.12 TX, RX inverting enable4.6.12 TX, RX inverting enable4.6.12 TX, RX inverting enable4.6.12 TX, RX inverting enable This item allows you to enable the TX, RX inverting which depends on different H/W requirement. This field is not recommended to change its default setting to avoid any error in your system. The choices are: No, No/No, Yes/Yes, No/Yes, and Yes. 4.6.13 4.6.13 4.6.13 4.6.13 OnboaOnboaOnboaOnboard Parallel Portrd Parallel Portrd Parallel Portrd Parallel Port This item allows you to determine access onboard parallel port controller with which I/O address. The choices are: 378H/IRQ7, 278H/IRQ5, 3BC/IRQ7, and Disabled. 4.6.14 4.6.14 4.6.14 4.6.14 Onboard Parallel ModeOnboard Parallel ModeOnboard Parallel ModeOnboard Parallel Mode Select an operating mode for the onboard parallel (printer) port. Select Normal unless your hardware and software require one of the other modes offered in this field. SPP Standard parallel port mode (Default) EPP Bi-directional mode ECP Fast, buffered ECP+EPP Bi-directional and buffered 4.6.15 4.6.15 4.6.15 4.6.15 ECPECPECPECP Mode Use DMA Mode Use DMA Mode Use DMA Mode Use DMA Select a DMA channel for the parallel port for use during ECP mode. The choices are: 3, and 1.

55 4. BIOS Setup4. BIOS Setup4. BIOS Setup4. BIOS Setup 4.6.16 Parallel Port EPP Type4.6.16 Parallel Port EPP Type4.6.16 Parallel Port EPP Type4.6.16 Parallel Port EPP Type Select EPP port type. The choices are: EPP 1.7, and 1.9 4.6.17 SB I/O Base Address4.6.17 SB I/O Base Address4.6.17 SB I/O Base Address4.6.17 SB I/O Base Address 4.6.18 SB IRQ Select4.6.18 SB IRQ Select4.6.18 SB IRQ Select4.6.18 SB IRQ Select 4.6.19 SB 4.6.19 SB 4.6.19 SB 4.6.19 SB DMA SelectDMA SelectDMA SelectDMA Select 4.6.20 MPU4.6.20 MPU4.6.20 MPU4.6.20 MPU----401401401401 4.6.21 MPU4.6.21 MPU4.6.21 MPU4.6.21 MPU----401 I/O Address401 I/O Address401 I/O Address401 I/O Address 4.6.22 Game Port (2004.6.22 Game Port (2004.6.22 Game Port (2004.6.22 Game Port (200----207H)207H)207H)207H)

56 4. BIOS Setup4. BIOS Setup4. BIOS Setup4. BIOS Setup 4.7 Power Management Setup Menu4.7 Power Management Setup Menu4.7 Power Management Setup Menu4.7 Power Management Setup Menu The Power Management Setup allows you to configure your system to most effectively save energy while operating in a manner consistent with your own style of computer use. Figure 6: Power Management Setup Menu 4.7.1 ACPI function4.7.1 ACPI function4.7.1 ACPI function4.7.1 ACPI function ACPI (Advanced Configuration and Power Interface) evolves the existing motherboard configuration interfaces to support these advanced architectures in a more robust, and potentially more efficient manner.

57 4. BIOS Setup4. BIOS Setup4. BIOS Setup4. BIOS Setup 4.7.2 Power Management4.7.2 Power Management4.7.2 Power Management4.7.2 Power Management This option allows you to select the type (or degree) of power saving for Doze, Standby, and Suspend modes. See the section 4.7.2.1 PM Timers for a brief description of each mode. This table describes each power management mode: Disable No power management. Disables all four modes. Max Saving Maximum power management. Only Available for SL CPUs. Doze Mode = 1 min., Standby Mode = 1 min., Suspend Mode = 1 min., and HDD Power Down = 1 min. User Defined Allows you to set each mode individually. When not disabled, each of the ranges are from 1 min. to 1 hr. except for HDD Power Down which ranges from 1 min. to 15 min. and disable. Min Saving Minimum power management. Doze Mode = 1 hr., Standby Mode = 1 hr., Suspend Mode = 1 hr., and HDD Power Down = 15 min. 4.7.2.1 PM Timers4.7.2.1 PM Timers4.7.2.1 PM Timers4.7.2.1 PM Timers This category allows you to select the type (or degree) of power saving and is directly related to the following modes: 1. HDD Power Down – When enabled and after the set time of system inactivity, the hard disk drive will be powered down while all other devices remain active. 2. Doze Mode – When enabled and after the set time of system inactivity, the CPU clock will run at slower speed while all other devices remain active. 3. Suspend Mode – When enabled and after the set time of system inactivity, all devices except the CPU will be shut off. 4.7.3 PM Control by APM4.7.3 PM Control by APM4.7.3 PM Control by APM4.7.3 PM Control by APM If Advanced Power Management (APM) is installed on your system, selecting Yes gives better power savings.

58 4. BIOS Setup4. BIOS Setup4. BIOS Setup4. BIOS Setup 4.7.4 Video Off Option4.7.4 Video Off Option4.7.4 Video Off Option4.7.4 Video Off Option When enabled, this feature allows the VGA adapter to operate in a power saving mode. Always On Monitor will remain on during power saving modes. Suspend # Off Monitor blanks when the system enters the Suspend mode. Suspend, or Standby # Off Monitor blanks when the system enters either Suspend or Standby modes. All Modes # Off Monitor blanks when the system enters any power saving modes. 4.7.5 Video Off Method4.7.5 Video Off Method4.7.5 Video Off Method4.7.5 Video Off Method Determines the manner in which the monitor is blanked. V/H SYNC+Blank System turns off vertical and horizontal synchronization ports and writes blanks to the video buffer. DPMS Support Select this option if your monitor supports the Display Power Management Signaling (DPMS) standard of the Video Electronics Standards Association (VESA). Use the software supplied for your video subsystem to select video power management values. Blank Screen System only writes blanks to the video buffer. 4.7.6 Modem Use IRQ4.7.6 Modem Use IRQ4.7.6 Modem Use IRQ4.7.6 Modem Use IRQ This determines the IRQ in which the MODEM can use. The choices are: 3, 4, 5, 7, 9, 10, 11, and NA. 4.7.7 Soft4.7.7 Soft4.7.7 Soft4.7.7 Soft----Off by PWRBTNOff by PWRBTNOff by PWRBTNOff by PWRBTN This item allows you to select the function of power button. The choices: Instant-Off, and Delay 4 Sec. 4.7.8 Keyboard Power On4.7.8 Keyboard Power On4.7.8 Keyboard Power On4.7.8 Keyboard Power On This option allows you to use PS/2 keyboard by pressing any key or specific key. The choices are: Enabled, and Disabled.

59 4. BIOS Setup4. BIOS Setup4. BIOS Setup4. BIOS Setup 4.7.9 Wake4.7.9 Wake4.7.9 Wake4.7.9 Wake----Up EventsUp EventsUp EventsUp Events Wake-Up events are I/O events whose occurrence can prevent the system from entering a power saving mode or can awaken the system from such a mode. In effect, the system remains alert for anything which occurs to a device which is configured as ON, even when the system is in a power down mode. Continued on the next page. 1. VGA – When Enabled, you can set the VGA awakens the system. 2. LPT & COM – When ON of LPT & COM, any activity from one of the listed system peripheral devices or IRQs wakes up the system. 3. HDD & FDD – When ON of HDD & FDD, any activity from one of the listed system peripheral devices wakes up the system. 4. PCI Master – When ON of PCI Master, any activity from one of the listed system peripheral device wakes up the system. 5. Wake on Ring or LAN - An input signal on the serial Ring Indicator line (in other words, an incoming call on the modem) awakens the system from a soft off state. 6. RTC Alarm Resume – When Enabled, you can set the date and time at which the RTC (real-time clock) alarm awakens the system from Suspend mode. The following is a list of IRQs, which can be exempted much as COM ports and LPT ports above can. When an I/O device wants to gain the attention of the operating system, it signals this by causing an IRQ to occur. When the operating system is ready to respond to the request, it interrupts itself and performs the service. When set ON, activity will neither prevent the system from going into a power management mode nor awaken it. • Primary INTR • IRQ3 (COM 2) • IRQ4 (COM 1) • IRQ5 (LPT 2) • IRQ6 (Floppy Disk) • IRQ7 (LPT 1) • IRQ8 (RTC Alarm) • IRQ9 (IRQ2 Redir) • IRQ10 (Reserved) • IRQ11 (Reserved) • IRQ12 (PS/2 Mouse) • IRQ13 (Coprocessor) • IRQ14 (Hard Disk) • IRQ15 (Reserved)

60 4. BIOS Setup4. BIOS Setup4. BIOS Setup4. BIOS Setup 4.8 PnP/PCI Configurations Menu4.8 PnP/PCI Configurations Menu4.8 PnP/PCI Configurations Menu4.8 PnP/PCI Configurations Menu Figure 7: PnP/PCI Configurations Menu 4.8.1 PNP OS Installed4.8.1 PNP OS Installed4.8.1 PNP OS Installed4.8.1 PNP OS Installed The default setting is No when a non-PnP OS installed or to prevent reassigning of interrupt setting for some of non-PnP cards installed. Select Yes if the OS is PnP aware (e.g. Windows 95). 4.8.2 Reset Configuration Data4.8.2 Reset Configuration Data4.8.2 Reset Configuration Data4.8.2 Reset Configuration Data Select Enabled to reset Extended System Configuration Date (ESCD) when you exit Setup if you have installed a new add-on and the system reconfiguration has caused such a serious conflict that the operating system cannot boot. 4.8.3 Resources Controlled By4.8.3 Resources Controlled By4.8.3 Resources Controlled By4.8.3 Resources Controlled By The Award Plug and Play BIOS can automatically configure all the boot and Plug and Play-compatible devices. If you select Auto, all the interrupt request (IRQ) and DMA assignment fields disappear, as the BIOS automatically assign them. 4.8.4 PCI/VGA Palette Snoop4.8.4 PCI/VGA Palette Snoop4.8.4 PCI/VGA Palette Snoop4.8.4 PCI/VGA Palette Snoop Some display cards that are not standard VGA card such as graphics accelerators or MPEG cards may not show the correct colors. This setting can correct this problem once you set it to enable. To default setting, leaves at Disabled.

61 4. BIOS Setup4. BIOS Setup4. BIOS Setup4. BIOS Setup 4.8.5 Assign IRQ for VGA4.8.5 Assign IRQ for VGA4.8.5 Assign IRQ for VGA4.8.5 Assign IRQ for VGA Choose Enabled to assign an IRQ automatically for some specific VGA to make sure the system can operate normally. 4.8.6 Assign IRQ for USB4.8.6 Assign IRQ for USB4.8.6 Assign IRQ for USB4.8.6 Assign IRQ for USB Choose Enabled if you want to use an USB mouse under DOS environment.

62 4. BIOS Setup4. BIOS Setup4. BIOS Setup4. BIOS Setup 4.9 PC Health Status4.9 PC Health Status4.9 PC Health Status4.9 PC Health Status Figure 8: PC Health Status 4.9.1 Chassis Intrusion4.9.1 Chassis Intrusion4.9.1 Chassis Intrusion4.9.1 Chassis Intrusion Choose Enabled to display the error message once the system cover has been opened by anyone.

63 4. BIOS Setup4. BIOS Setup4. BIOS Setup4. BIOS Setup 4.10 Frequency/Voltage Contro4.10 Frequency/Voltage Contro4.10 Frequency/Voltage Contro4.10 Frequency/Voltage Controllll Figure 9: Frequency/Voltage Control 4.10.1 Auto Detect DIMM/PCI Clk4.10.1 Auto Detect DIMM/PCI Clk4.10.1 Auto Detect DIMM/PCI Clk4.10.1 Auto Detect DIMM/PCI Clk Keeping this feature at Enabled allows the system to detect the DIMM clock automatically. The choices are: Enabled (Default) and Disabled. 4.10.2 Spread Spectrum4.10.2 Spread Spectrum4.10.2 Spread Spectrum4.10.2 Spread Spectrum This feature is used to set the spread spectrum to be spread type or down spread type. The choices are: Enabled, and Disabled (Default).

64 4. BIOS Setup4. BIOS Setup4. BIOS Setup4. BIOS Setup 4.11 Load Optimized Defaults4.11 Load Optimized Defaults4.11 Load Optimized Defaults4.11 Load Optimized Defaults The chipset defaults are settings, which provide for maximum system performance. While Award has designed the custom BIOS to maximize performance, the manufacturer has the right to change these defaults to meet their needs. 4.12 Set User Password 4.12 Set User Password 4.12 Set User Password 4.12 Set User Password When you select this function, a message appears at the center of the screen: ENTER PASSWORD: Type the password, up to eight characters, and press Enter. Typing a password clears any previously entered password from CMOS memory. Now the message changes: CONFIRM PASSWARD: Again, type the password and press Enter. To abort the process at any time, press Esc. In the Security Option item in the BIOS Features Setup screen select System or Setup: !" System: Enter a password each time the system boots and whenever you enter Setup. !" Setup: Enter a password whenever you enter Setup. NOTE: To clear the password, simply press Enter when asked to enter a password. Then the password function is disabled. 4.13 Save & Exit Setup4.13 Save & Exit Setup4.13 Save & Exit Setup4.13 Save & Exit Setup This feature allows the changes to be made to the CMOS setup to be saved. The system will resume booting after a successful save. 4.14 Exit Wit4.14 Exit Wit4.14 Exit Wit4.14 Exit Without Savinghout Savinghout Savinghout Saving Abandon all CMOS value change without saving.

Navigation menu

Upload a User Manual

Namespaces

Wiki Guide
HTML
PDF
Info

Views

User Manual
Discussion / Help

Navigation

© 2024 UserManual.wiki | Privacy Policy

Contact Us
DMCA