GUARDIAN ACRX01-CC Garage Door Opener User Manual

GUARDIAN SHANGHAI CORP. Garage Door Opener Users Manual

Users Manual

Owner’s Manual●Please read and understand this manual and safety instructions carefully before installation.●The Opener WILL NOT CLOSE until the Photo Eye Safety System is properly installed and aligned.●REGULARLY CHECK and TEST the Opener according to the safety label to ENSURE SAFE OPERATION.●Retain this manual for future reference.GDO Manual Revised: 03-17 GDOMU10A-7WARNING: To reduce the risk of injury to persons - Use this operator only with Residential Sectional Garage doors. Serial # __ __ __ __ __ __ __ Date Installed __ __ /__ __ /__ __ __ __ Located on the bar code label on top of your opener.The illustrations used in this instruction manual may differ from the actual product you have purchased.
1 Courtesy light turns on/flashes with audible ‘click’. (If light bulb is not installed, ‘click’ represents the light)DO NOT connect power Please connect powerSymbols and Icons ! WARNINGInstallation hardware Introduction Symbols and Icons 1 Inventory 2 Read and Follow These Important Safety Instructions 3 Preparation / Door Balance Test 4 Tools Required 4 Assembly T-rail Assembly and Tensioning 5 Mounting Header Bracket 6 Installation Attaching the Opener Assembly to Header Bracket 7 Mounting Door Bracket 7 Mounting Opener to Ceiling 8 Attaching Door Arms 9 Installing Light and Emergency Release Handle 10 Wiring Wiring Instructions 11 Connecting Photo Eye Safety System 12 Connecting Push Button 13 Connecting Power 14 Adjustment Aligning the Photo Eye Safety System 14 Travel Limit Adjustment 15 Force Adjustment 16 Final Adjustment and Testing 17 Operation Programming Remote Controls* (OPTIONAL) 18 Operating the Opener 19-20 Maintenance 21 Troubleshooting 21 Repair Parts and Service Installation and Accessory Parts 22 Opener Assembly parts 23 Warranty 24 Table of Contents READ WARNINGS CAREFULLY to prevent SERIOUS INJURY or DEATH caused by electrocution or mechanical hazard.
2 Emergency Release Handle + Rope Literature + Safety Labels Photo Eye Safety System Door Bracket Door Arms Inventory Remote Control Push Button Header Bracket Clevis Pin Long x1 5/16’’ x 2-1/4’’ Hitch Pin — Locking Clevis Pins x1 x 2 Hitch Pin — Locking Clevis Pins x 2 Lag Screw 5/16” x 1-5/8” — Door Bracket / Mounting Opener Bolt 5/16” -18 x 1” 5/16” Flange Nut x 6 x 6 x 4 x 2 Clevis Pin — Door arms 5/16” x 1” INSTALLATION HARDWARE, LOCATED IN HARDWARE BAG (SHOWN IN ACTUAL SIZE 1:1) Lag Screw 5/16” x 2 1/2” — Header Bracket / Mounting Opener x 2 x 4 Emergency Release Handle + Rope Flange Nut 1/4” -20 Lag Screw 1/4” x 1” — Door Bracket x 2 Lag Screw 1/4” x 1” — Photo Eye System Opener Unit + Lamp Dome ( Light bulb are not included ) Hexagonal Screw #10 - 24 x 1/2” Spring Washer #10 Washer #10 x 1 x 1 x 1 x 1 — Door arms / Mounting Opener T-rail Assembly Drywall Anchor x 2 x 2 Screw #6 x 1” Door Control included in some models 3-FDCC 1-FDCC Standard Door Control
5 Fig.2 1 Tighten until... 2 Tighten nut Flange Nut Chain to Cable Connector To Tighten the Chain: Follow steps shown in Fig.2 to tighten the chain: 1. Turn the Chain-to-Cable Connector on the Trolley Shaft until the chain is about 1/4” (6mm) above the base of the rail. Compare with the illustration below. 2. Tighten the Flange Nut on Trolley Shaft against the Chain-to-Cable Connector. Notice During operation, it is normal for the chain to appear loose when the door is closed. If the chain returns to the position as shown below when the door is opened, the chain is adjusted properly. DO NOT re-tighten the chain. When performing maintenance, always PULL the Emergency Release to DISCONNECT the door from Opener before adjusting the chain. 1/4” (6mm) Base of Rail Mid-point of rail assembly Chain Top of Rail Actual Size T-rail Assembly and Tensioning Fig.1 ! CAUTION - DO NOT connect power until instructed. - To prevent INJURY, keep hands and fingers away from joints and possible sharp edges. - Wear gloves when installing chain and cable. 2 3 4 1/4” Flange Nut x 4 Screw Spring Washer Washer To Assemble the Rail Align the pre-assembled T-rail on the top of opener in the direction as shown in Fig.1. Secure the T-rail to the opener firmly using 1/4” flange nut x 4. Final Step to T-Rail Installation Fasten the Screw(2) to the motor shaft with spring washer(3) and washer(4) in between. Note: The chain or belt rail assembly comes pre-tensioned from the factory. If installing with the optional belt rail, follow the same adjustment steps. #10 - 24 x 1/2”
13 To Connect the Push Button to the Opener Connect the pair of wires from the Push Button to the pair of “PUSH BUTTON” terminals on the rear of the Opener. Refer to Wiring Instructions on page 12 to ensure wires are properly connected. The Push Button is a wired, illuminated door control placed inside your garage. To install the Push Button: 1. Inside your garage, install Push Button within sight of the door at a minimum height of 5 feet (1.5m) off the ground. Ensure it is installed out of the reach of children and free from the moving parts of the door and hardware. 2. Securely fasten it to a solid surface with # 6x1-3/8” screws provided. If attaching to drywall or other hollow surface, drill 3/16” holes and use the provided Drywall Anchors. To prevent SERIOUS INJURY or DEATH from electrocution: - Power MUST NOT be connected until instructed. To prevent SERIOUS INJURY or DEATH from using the Push Button and a closing door: - Install the Push Button within sight of the door at a minimum height of 5 feet (1.5m) above the floor. Make sure it is out of the reach of children and moving parts of door and hardware. - NEVER permit children to access the Push Button or Remote Controls. - Operate the door ONLY when it is adjusted properly with no obstructions present and is in clear sight. - ALWAYS keep a moving door in sight until it’s completely closed. - NEVER cross the path of a moving door. Push Button Min. 5 feet (1.5m) above floor From Push Button Connecting Push Button ! WARNING Drywall Anchor Screw #6 x1-3/8”
20 In case of a power failure or door obstruction, PULL EMERGENCY Handle to release door from Opener. To Disconnect Trolley for Manual Operation With the door closed, pull down the emergency release Handle to the DISCONNECT position. The door can be raised / lowered manually. To Re-connect Trolley Pull the Handle toward the Opener so that the lever will flip up to the CONNECT position. The Trolley will reconnect itself when the Opener is activated or when the door is manually opened/closed Operation / Condition Courtesy Light ResponseOpener is initially plugged-in / Power restored Flashes 5 timesUpon Opener activation Turns on for 4-1/2 minutes and turns off automatically“LEARN” button is pressed Turns on for 30 secondsRemote Control / Keyless Entry PIN code accepted Flashes 5 timesThe Photo Eye System is obstructed during door-closing or door is obstructed during opening Flashes for 30 seconds (Re-align and clear obstruction)Opener motor overheat (Thermal Protection) Flashes 5 times (Wait about 15 minutes to cool down)Courtesy Light ResponsesManual OperationDoor status Activation using Push Button / Remote Con-trolDoor at fully open / close position Door will move to fully close / open positionDoor is closing Door will reverseDoor is opening Door will stopDoor is stopped as intended in partially open position CloseDoor is obstructed while closing Door will reverse while flashing courtesy lightDoor is obstructed while opening Door will stopDoor is fully opened and Photo Eye System is obstructed Door will not closeDoor Status vs. ActivationOperating the Opener ! WARNINGTo Prevent SERIOUS INJURY or DEATH: - Use Emergency Release to disconnect Trolley ONLY when the door is CLOSED to prevent unexpected rapid falling in case of a unbalanced / poor-conditioned door. - Use Emergency Release ONLY when doorway is clear of persons and obstructions. - DO NOT use Emergency Release to pull the door open or closed.Lever CONNECT DISCONNECT Pull to Disconnect Flip to reconnect
21 Troubleshooting Problem Possible Cause / SolutionOpener does not close and light flashes The Photo Eye may be obstructed, not properly aligned or installed, check connection and alignment referring to pages 12 & 14.Opener does not respond to Remote Control - Refer page 18 to reprogram Remote Control. - Check Remote Control batteryOpener stops before reaching full open / close positionEither the Travel Limit or Force is not properly adjusted, check adjustment referring to pages 15-16. Conduct Safety Reverse Test after ANY adjustment.The door reverses unintentionally- Make sure the Photo Eye Safety System is aligned and clear of obstructions.- Refer to page 4 to check the door balance - Refer to page 16-18 to re-adjust the forceThe door reverses upon touching the floor and the courtesy light flashesRefer to page 15 to decrease Close Limit by 1/4 turn until door stops as intended at the fully closed position. Conduct Safety Reverse Test after ANY adjustment.The courtesy light flashes 5 times and the Opener does not start Opener motor overheat, please wait about 15 minutes and retry.The Opener does not close the door and the green LED on the Photo Eyes flashes The Photo Eye Safety System is misaligned or obstructed, refer to page14 for proper alignment.The Opener is working properly but the courtesy light does not turn on Replace light bulb (A19 incandescent Max.100W).The courtesy light does not turn off Defective Logic Board.Schedule MaintenanceOnce a month Door balance test, refer to page 4. Safety reverse test, refer to page 17.Twice a year Check chain tension ( refer to page 5 for adjustment if necessary).Once a year- Limit and Force adjustment may be necessary due to weather conditions. Refer to pages 15-16 for adjustment. Conduct Safety Reverse Test after ANY adjustments. - Lubricate door rollers, bearings and hinges. The Opener is permanently lubricated, DO NOT lubricate or grease the Opener, rail or door tracks.Maintenance Red LED Green LEDGreen LEDGreen LED Red LED Green LEDRed LEDRed LED Green LED Red LEDNote: If installing operators on two doors in the same garage, to ensure proper operation, Photo Eyes should be aligned as below: Green LED Red LED
22 Installation Parts 234 5 61Repair Parts Item Part No. Name / Description1GUAT-027 Header Bracket2GUAT-022 Door Bracket3GUAT-023 Hardware Bag (Installation hardware shown on P.3)4GUAT-024 Curved Door Arm5GUAT-025 Straight Door Arm6GUAT-026 Emergency Release Handle & RopeAccessoriesItem Part No. Name / Description1GUAT-201 Photo Eye Safety System (Emitter + Sensor with Brackets)2GUAT-202 Push button3GUAT-203 12V alkaline battery4R2BCC Remote Control5GUAT-205 Owner’s manual12354
Manufacturer hereby warrants: 1. Garage Door Operators to be free from defects in material and workmanship for a period of five (5) years for motors andone (1) year for Electronics and Mechanics from date of purchase, if installed by an authorized reseller, otherwise if in-stalled by the purchaser one (1) year will apply.2. Garage Door Operators (Commercial and Industrial Application) to be free from defects in material and workmanship fora period of three (3) months from date of purchase.3. Where the garage door operator has been returned to the manufacturer for Warranty repairs, all costs incurred in thereturn will be paid for by the purchaser. If in the opinion of the manufacturer the product is faulty, all defective parts willbe replaced at no charge to the purchaser.4. Proof of purchase must be given to the manufacturer at time of Warranty claim.5. The manufacturer reserves the right to modify any existing or future products without incurring any obligation to incor-porate such modification to products already manufactured or to which this Warranty may relate.6. Warranty only applies if this product has been installed to the Manufacturers recommendation7. This Warranty does not apply to any defect, loss or damage arising or caused directly or indirectly by or as a result of :(i) Any defect (including detects in component parts or accessories) arising from or attributable to the failure to carryout normal preventive maintenance or adjustment itself. (ii) To any additional damage or deterioration arising from attributable to the operation of the Operator after it is known to be defective. 8. Exclusions to Warranty Period:(i) Repair or Warranty Work - three (3) month9. Not included in Warranty:(i) Batteries.(ii) Fuses.(iii) Light bulbs.(iv) Sensitivity adjustment.(v) Handheld Remote Controls and receiver range.10. Note : All Warranties will be void subject to:(i) Water damage and condensation.(ii) Power supply black out or surge.(iii) Act of God.(iv) Modification or adjustment by unauthorized persons.(v) Any interference from radio (including citizen band radios or and other electronic device)(vi) Preventative maintenance and regular servicing not undertaken.(vii) Account not paid in full by the purchaser.11. Subject only to the provisions of the Trade practices Act and any legislation of the State or Territory wherein the oper-ators of the Manufacturer have been sold or installed (which may confer certain rights on consumers of goods andthose rights by such legislation may be rendered incapable of exclusion) this Warranty supersedes and excludes allrepresentations, warranties and conditions whether expressed or implied by law and the Manufacturer shall have noliability or otherwise than herein provided for any loss and damage (including consequential loss and damage, loss ofuse or profits) by reasons of delay, defective or faulty materials or workmanship, negligence or any act, matter or thingdone permitted or omitted to be done by the Manufacturer. WARRANTY THIS WARRANTY FORM SHOULD BE COMPLETED AT TIME OF INSTALLATION This Warranty Form should be retained by the purchaser at all times and produced with the purchase docket by the Pur-chaser as proof of the purchase date. PURCHASER’S NAME: PURCHASER’S ADDRESS: INSTALLED BY: INSTALLER’S ADDRESS: INSTALLER’S SIGNATURE: SERIAL NUMBER OF THE OPERATOR: GUARDIAN SERVICE Your operator has been installed by a professional installation specialist. If service information is required please contact the installing company or your local Guardian dealer. Look for your Guardian dealer online, in the yellow pages or call our service number for a dealer near you.Service number : 1-424-272-6998Please have the following information when you call: ·Model number of the operator·Serial number of the operator--located on the bar code label on top of the opener, above the adjustment buttonsWARRANTYGARAGE DOOR OPERATORS
FCC Warning:Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna.—Increase the separation between the equipment and receiver.—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help.

Navigation menu