GUARDIAN 303RX-MBT Garage Door Opener User Manual

GUARDIAN SHANGHAI CORP. Garage Door Opener Users Manual

Users Manual

Owner’s Manual ● Please read and understand this manual and safety instructions carefully before installation. ● The Opener WILL NOT CLOSE until the Photo Eye Safety System is properly installed and aligned. ● REGULARLY CHECK and TEST the Opener according to the safety label to ENSURE SAFE OPERATION. ● Retain this manual for future reference. GDO Manual Revised: 03-16 GDOMU14A-1 WARNING: To reduce the risk of injury to persons - Use this operator only with Residential Sectional Garage doors. Serial # __ __ __ __ __ __ __ Date Installed __ __ /__ __ /__ __ __ __ Located on the bar code label on top of your opener. The illustrations used in this instruction manual may differ from the actual product you have purchased.
2 Beeps from built-in buzzer of the opener DO NOT connect power Please connect power Introduction Symbols and Icons 2 Inventory 3 Preparation / Door Balance Test 4 Tools Required 4 Assembly Assembling T-Rail 5 Tension the Belt 6 Installation Mounting Header Bracket 7 Attaching Rail to Header Bracket and Mounting Door Bracket 8 Mounting Opener to Ceiling 9 Attaching Door Arms 10 Installing Light and Emergency Release Handle 11 Wiring Wiring Instructions 12 Connecting Photo Eye Safety System 13 Connecting Speaker and Door Control Console 14 Bluetooth Music Playback / Hands Free Features 15 Connecting Power 16 Adjustment Aligning the Photo Eye Safety System 16 Travel Limit Adjustment—I. UP Limit 17 Travel Limit Adjustment—II. DOWN Limit 18 Auto Force Adjustment 19 Final Adjustment and Testing 20 Operation Programming Remote Controls 21 Operating the Opener 22-23 Maintenance 24 Troubleshooting 24 Repair Parts and Service Installation and Accessory Parts 25 Opener Assembly parts 26 FCC Statement 27 Warranty 28 Symbols and Icons ! WARNING READ WARNINGS CAREFULLY to prevent SERIOUS INJURY or DEATH caused by electrocution or mechanical hazard. Installation hardware shown in actual size Table of Contents
3 Door Bracket Inventory Drywall Anchor x 2 x 2 Screw #6 x 1” Photo Eye Safety System Literature + Safety Labels Door Arms Remote Control Header Bracket Clevis Pin Long x1 5/16’’ x 2-1/4’’ Hitch Pin — Locking Clevis Pins x1 Emergency Release Handle + Rope INSTALLATION HARDWARE, LOCATED IN HARDWARE BAG (SHOWN IN ACTUAL SIZE 1:1) Speaker and Door Control Console x 2 Hitch Pin — Locking Clevis Pins x 2 Lag Screw 5/16” x 1 5/8” — Door Bracket Bolt 5/16” -18 x 1” 5/16” Flange Nut x 6 x 6 x 4 x 2 Clevis Pin — Door arms 5/16” x 1” INSTALLATION HARDWARE, LOCATED IN HARDWARE BAG (SHOWN IN ACTUAL SIZE 1:1) Lag Screw 5/16” x 2 1/2” — Header Bracket x 2 x 4 Emergency Release Handle + Rope Flange Nut 1/4” -20 Sheet Metal Screw 1/4” x 1” — Door Bracket x 2 Lag Screw 1/4” x 1” — Photo Eye System Hexagonal Screw #10 - 24 x 1/2” Spring Washer #10 Washer #10 x 1 x 1 x 1 x 1 — Door arms / Mounting Opener T-rail Assembly ( Light bulbs are not included) Opener Unit + Light Lens Cover
4 Level Tape Measure Hack Saw Pencil Drill, 3/16” and 5/16” Drill Bits Tools Required Step Ladder Screwdriver Hammer Sectional Garage Door BEFORE Beginning Installation: 1. Disable locks and remove all ropes connected to the garage door. 2. Perform the following door test to ensure your door is balanced and in good working condition. To Test Your Garage Door 1. Raise and lower the door to check if there is any sticking or binding. 2. Check for loose hinges, damaged rollers, frayed cables and damaged or broken springs. 3. Lift the door approximately halfway and release. The door should stay at the point under proper spring tension. Call a qualified garage door service technician if your door binds, sticks or is unbalanced. ! WARNING To prevent SERIOUS INJURY or DEATH: - Before beginning installation of the Opener please complete the following test to ensure that your door is balanced and in good working condition. - A poorly balanced door can cause serious injury and damage to the Opener. - Always have a qualified garage door service technician make any required adjustments and/or repairs to your door before proceeding with installation. - DISABLE ALL LOCKS and REMOVE ALL ROPES connected to the garage door BEFORE installing and/or operating the Opener. To prevent damage to the door and Opener: - DO NOT connect power until instructed. - Operate this Opener with AC 120V/60Hz power supply ONLY. Adjustable Wrench Ratchet with 5/16”, 7/16” and 1/2” sockets Preparation Pliers Rubber Mallet
5 ! CAUTION - DO NOT connect power until instructed. - To prevent INJURY, keep hands and fingers away from joints and possible sharp edges. - Wear gloves when installing chain/belt and cable. ! WARNING To prevent SERIOUS INJURY: - DO NOT connect power until instructed. - Keep hands and fingers clear from sprocket during operation. - Wear gloves when installing chain/belt and cable. - Keep hands and fingers away from joints and possible sharp edges. Fig.1 Assembling T-Rail 2 3 4 1/4” Flange Nut x 4 To Assemble the Rail Align the pre-assembled T-rail on the top of opener in the direction as shown in Fig.1. Secure the T-rail to the opener firmly using 1/4” flange nut x 4. Final Step to T-Rail Installation Fasten the Screw(2) to the motor shaft with spring washer(3) and washer(4) in between. Hexagonal Screw #10 - 24 x 1/2” Spring Washer #10 Washer #10
6 ! WARNING To prevent SERIOUS INJURY: - DO NOT connect power until instructed. - Keep hands and fingers clear from sprocket during operation. - Wear gloves when installing chain/belt and cable. - Keep hands and fingers away from joints and possible sharp edges. Shaft-Linker Tighten until... Tighten nut Flange Nut 2 1/4” (6mm) Base of Rail Mid-point of rail assembly Belt Top of Rail Actual Size 1 Note: The chain or belt rail assembly comes pre-tensioned from the factory. Tension the Belt 1. Rotate the Shaft Linker towards the Trolley Shaft until the belt is slightly loose about 1/4” (6mm) above the base of the rail, referring to the actual-sized illustration below. 2. Tighten the Flange Nut on Trolley Shaft against the Shaft-Linker. Remove the temporary screw driver holding the position of the trolley. Tension the Belt / Chain
7 To Install Header Bracket Note: Installation procedures may vary according to door type. 1. While inside your garage, close the door and mark the vertical centerline of the garage door. Extend the line onto the header wall above the door spring. 2. Open the door to the highest point of travel. Mark a line on the header wall 2” (5cm) above the highest point of travel. Note: DO NOT install the Header Bracket over drywall. In some installations, it may be necessary to install a 2x4 across two wall studs to create a suitable location for the Header Bracket. If installing into masonry, use concrete anchors (not provided). Wall-Mounting As shown in Fig.2, place the Header Bracket on the vertical centerline in direction shown. Mark and drill two 3/16” holes. Fasten the Header Bracket securely to a structural support using two 5/16” x 2-1/2” Lag Screws. Alternative Ceiling-Mounting Ceiling-mounting is suggested ONLY when clearance is minimal. Extend the vertical centerline onto the ceiling as shown in Fig.3. Center the Header Bracket on the vertical mark, no more than 6” (15cm) from the header wall. Mark and drill holes to fasten the Header Bracket securely to a structural support. Fig.1 Ceiling Header Bracket Header Wall 2” (5cm) clearance Door Track Door Highest Point of Door Travel Support block on floor Door Spring ! WARNING To prevent SERIOUS INJURY: - DO NOT connect power until instructed. - The Header Bracket MUST be SECURELY fastened to the structural support on the mounting wall or ceiling, otherwise the door may not reverse when required. DO NOT install the Header Bracket over drywall. - Concrete anchors MUST be used when mounting the Header Bracket into masonry. - NEVER try to loosen, move or adjust garage door springs, cables, Pulleys, Brackets, or hardware, all of which are under EXTREME tension. - Contact a qualified garage door service technician if your door binds, sticks or is unbalanced. An unbalanced door might not reverse when required. Mounting Header Bracket UP OPENER MAX. 6” (15cm) Highest Point of Door Travel Vertical Centerline Horizontal Line Finished Ceiling Lag Screw 5/16” x 2-1/2” Vertical Centerline Fig.2 (Wall-Mounting) Fig.3 (Ceiling-Mounting)
8 ! CAUTION To prevent SERIOUS INJURY: - DO NOT connect power until instructed. - REINFORCEMENT is recommended for fiberglass, aluminum or lightweight steel garage doors BEFORE installing the door Bracket. Contact your door manufacturer for reinforcement options. Fig.1 Fig.3 (a) (b) (c) To Attach the Opener to the Header Bracket 1. As shown in Fig.1, use the packaging carton as temporary support for the Opener. Place the Opener on carton to prevent damage. 2. Align the mounting hole on the header rail to the mounting hole on the Header Bracket. 3. Connect the Header Rail and the Door Bracket together with a 5/16” x 2-1/4” Clevis Pin and lock it in place with a Hitch Pin. To mount the Door Bracket Note: Some door reinforcement kits may provide direct attachment of the door arm to the reinforcement bracket. If you have a door reinforcement bracket with this option, skip this step and proceed with the next step “Mounting Opener to Ceiling”. 1. Position the Door Bracket on the centerline of the door approximately 2” - 4” (5-10cm) below the top edge of the door. Secure the Door Bracket with 5/16” x 1 5/8” Lag Screw (provided) as shown in Fig.2. 2. Alternately, depending on the construction of your door, install using one of the steps shown if Fig. 3 below: For steel / lightweight doors with vertical steel reinforcements / factory reinforced. (a) Mark and drill two 3/16” holes. Make sure not to drill through the garage door. Secure the Door Bracket with two 1/4” x 1” Sheet Metal Screws (provided) as shown in Fig.3(a). (b) Alternative installation: Drill two 5/16” holes through the door. Secure the Door Bracket using two 5/16” carriage Bolts, lock washers and nuts (not provided) as shown in Fig.3(b). The length of bolts will depend on the thickness of your door. Wood door (c) Mark and drill two 5/16” holes through the garage door. Secure the Door Bracket using two 5/16” carriage bolts, washers and nuts (not provided) as shown in Fig.3(c). The length of bolts will depend on the thickness of your door. Note: DO NOT use Sheet Metal Screws on a wood door. Attaching Rail to Header Bracket and Mounting Door Bracket Fig.2 UP Vertical Centerline of Door 2-4” (5-10cm) Top Edge of Door Carton Clevis Pin - 5/16” x 2-1/4” Hitch Pin Lag Screw 5/16” x 1 5/8” Sheet Metal Screw 1/4” x 1” Not Provided Not Provided
9 ! WARNING To prevent SERIOUS INJURY or DEATH: - DO NOT connect power until instructed. - Install the Opener at least 7 feet (2.13m) above the floor. - Fasten the Opener SECURELY to STRUCTURAL SUPPORTS of the garage to prevent falling. - If installing Brackets to masonry, concrete anchors (not provided) MUST be used. Mounting Opener to Ceiling Angle Iron not provided Fig.1 Fig.2 Fig.3 Structural support Finished ceiling Bolt / Lock Washer / Nut Bolt / Lock Washer / Nut Angle Iron not provided Finished ceiling To Mount the Opener to Ceiling The three most common installation options are shown in Fig.1-3. Fig.1 shows mounting the Opener directly to structural support on the ceiling. Fig.2 and 3 show mounting on a finished ceiling, with heavy duty angle iron*. *angle iron not included Determine the mounting option that works best for your application and follow installation steps below: 1. Raise the Opener and rail assembly and temporarily place it on a stepladder. 2. Position the Opener and rail assembly so that it is aligned to the center line of the garage door. If the Header Bracket was mounted off center, align the Opener with the Header Bracket. 3. Measure the distance from each side of the Opener to the structural supports. 4. Cut both Hanging Brackets* to appropriate length *(Hanging Bracket not included) 5. Drill 3/16” holes in the structural supports. 6. Secure one end of each of the Hanging Brackets to the structural supports using 5/16”x2-1/2” Lag Screws (not provided). 7. Secure the Opener to the Hanging Brackets and secure each side with a 5/16”-18x1” Bolt and 5/16” Flange Nut (provided). 8. Move the door manually to check clearance between highest point of travel of the door and rail. If the door hits the rail, raise the Header Bracket or adjust the mounting of Opener. 9. Remove the ladder ONLY when the Opener is securely mounted to the structural supports. Bolt 5/16” - 18 x 1” 5/16” Flange Nut Securing Opener to Hanging Brackets
10 ! WARNING To prevent SERIOUS INJURY: - DO NOT connect power until instructed. - Keep hands and fingers away from the sprocket during operation. - Wear gloves when installing chain/belt and cable. - Keep hands and fingers away from joints and possible sharp edges. Attaching Door Arms Clevis Pin - 5/16” x 1” Hitch Pin Bolt 5/16” - 18x1” Flange Nut 1 2 Fig.1 To Connect Door Arm Follow the steps shown in Fig. 1 1. Fasten the Straight Door Arm to the Trolley with a 5/16” x 1” Clevis Pin and lock it with a Hitch Pin. 2. Fasten the Curved Door Arm to the Door Bracket with 5/16” x 1”Clevis Pin and lock it with a Hitch Pin. 3. To connect the door arms together, choose two pairs of holes which are as far apart as possible. Fasten the arms using two 5/16” x 1” Bolts and Flange Nuts. <1-3/4”mm >1-3/4”mm Ceiling Ceiling Rail of Opener Door Panel Rail of Opener Door Panel Curved Door Arm Straight Door Arm 1 2 3 NOTE: The straight door arm must be installed vertically to the door when door is at closed position.
11 ! WARNING To prevent SERIOUS INJURY or DEATH from electrocution: - Disconnect power cord before installing/replacing light bulb. To prevent possible OVERHEATING or damage to Opener: - Use ONLY A19 (E26) incandescent bulbs (100W max.). - DO NOT use short neck or specialty light bulbs. - DO NOT use halogen bulbs. Safety Notice Mount the emergency release within reach, but at least 6 feet above the floor and avoiding contact with vehicles to avoid accidental release. To attach the Emergency Release Handle: 1. Thread one end of the rope through the hole of the Emergency Release Handle and secure with an overhand knot. 2. Thread the other end of the rope through the hole in the Trolley lever. 3. Measure the rope length so that the handle is 6 feet (183cm) above the floor and is clear from the top of your vehicle. Secure with a overhand knot. Fig. 2 ! WARNING To prevent SERIOUS INJURY or DEATH from a falling garage door: - In case of power failure or door obstruction, PULL EMERGENCY HANDLE to release door from Opener. - When Emergency Release is in the released position, the door can be operated manually. - To reconnect, flip the lever on the Trolley towards Opener, back to Connect position, it will reconnect auto-matically upon pressing the Door Control Button on the Speaker and Door Control Console or Remote Con-trol. - DO NOT use Emergency handle to pull the door open or closed. Installing Light and Emergency Release Handle 6 feet (1.83m) above floor Lever Emergency Release Handle Fig. 2 To install light bulb as shown in Fig.1: 1. Install a standard A19 (E26) 100 watt maximum light bulb. 2. Re-attach the Light Lens Cover To replace light bulb as shown in Fig.2: 1. Press the release buttons and detach it from the Opener. 2. Replace light bulb and reattach the Light Lens Cover. Notice When replacing the light bulb, make sure the bulb on the Opener has cooled down to pre-vent injury. 1 2 Fig.1 2 100W MAX
12 In the following section, the Photo Eye Safety System and Door Control Console will be connected to the Opener. Please read and understand the wiring instructions before connecting wires. 1. Remove the pre-cut skin on the open end of wire from accessories. Wires MUST NOT be frayed and connected properly as shown in Fig.1. 2. To connect a wire to an assigned terminal, use a small “flat head” screwdriver to push in the orange tab on the Wire Terminal as shown in Fig.2. 3. Insert approximately 1/2” (13mm) of the wire into the terminal while pushing in the tab as shown in Fig.2. 4. Each accessory requires a pair of terminals, Each pair of terminals MUST be connected with one white wire and one striped wire (non-polarized) from the SAME accessory as shown in Fig.2. 5. Check for proper connection by gently pulling on the wire. The wire should not come out of the terminal. NO exposed part of the wire should be visible outside of the terminal. 6. Use the insulated staples provided to secure the wires to the wall and/or ceiling. Be careful not to damage the wires while securing the staples. ! WARNING To prevent SERIOUS INJURY or DEATH from electrocution: - Power MUST NOT be connected until instructed. - NO exposed part of the wire should be visible outside of the terminal for proper connection. Min. 5 feet (1.5m) above floor Wiring Instructions Photo Eye Safety System Fig. 2 Wire shown in actual size 1/2” Wire Terminals Fig. 1 2 3 Screwdriver or similar tool 1 Wire from accessories Remove and discard pre-cut skin PUSH BUTTON PHOTO EYE PUSH BUTTON PHOTO EYE Speaker and Door Control Console
13 ! WARNING To prevent SERIOUS INJURY or DEATH from electrocution: - Power MUST NOT be connected BEFORE Photo Eye Safety system is connected and aligned. - The Opener will not operate until the Photo Eye Safety System is properly connected and aligned. - Install the Photo Eyes NO higher than 6” (15cm) above the floor. No part of garage door or other objects should obstruct the Photo Eye Safety System during door-closing. Connecting Photo Eye Safety System About the Photo Eye Safety System The Photo Eye Safety System provides protection against entrapment while the door is closing. When properly connected and aligned, the emitter Photo Eye emits an invisible infrared light beam while the Sensor Photo Eye monitors that beam. If the beam is obstructed during door-closing, the entrapment protection will be triggered and the door will stop and reverse to the open position. The opener will beep for 20 times indicating an obstruction. Installing The Photo Eye Safety System Wall-mounting 1. Place the Photo Eyes facing each other on each side of the garage door. Position the sensors so they are no higher than 6” (15cm) above the floor, as shown in Fig.1. 2. Drill 3/16” holes using the mounting holes on the Bracket as a template. Secure with #12 x 1” Lag Screws (provided). 3. If necessary use the Optional Wall-mount Position (Fig.1) to better fit your door-track and improve obstacle avoidance. To adjust the position, loosen the wing nut, disassemble the Bracket and move the Photo Eye to the lower position on the holder. 4. If necessary, align the Photo Eyes by loosening the wing nut . (This step may be further required in Aligning the Photo Eye Safety System on page 16.) Alternative Floor-mounting 1. Place the Photo Eyes facing each other on each side of the garage door, as shown in Fig.2. 2. If attaching to concrete, secure the photo eyes using concrete anchors and bolts (not provided). 3. If necessary, align the Photo Eyes by loosening the wing nut. (This step may be further required in Aligning the Photo Eye Safety System on page 16.) To Connect Photo Eye Safety System 1. Connect a pair of wires from either one of the Photo Eyes to a pair of “PHOTO EYE” terminals on the rear of the Opener as shown in Fig. 3. Refer to Wiring Instructions on page 12 for proper connections. 2. Repeat above step to connect the other Photo Eye. 3. Refer to Wiring Instructions on page 12 to ensure wires are connected properly. Fig. 2 (Floor Mount) Fig. 3 From one of the Photo Eye From the other one Fig. 1 (Wall Mount) #12 x 1” Lag Screw Loosen Inside Garage Door Track 6” max. above floor Alignment Alignment Inside Garage Door Track 6” max. Inside Garage
14 ! WARNING To prevent SERIOUS INJURY or DEATH from electrocution: - Power MUST NOT be connected until instructed. To prevent SERIOUS INJURY or DEATH from using the Speaker and Door Control Console or Push Button and a closing door: - Install the Speaker and Door Control Console or Push Button within sight of the door at a minimum height of 5 feet (1.5m) above the floor. Make sure it is out of the reach of children and moving parts of door and hardware. - NEVER permit children to access the Speaker and Door Control Console, Push Button or Remote Controls. - Operate the door ONLY when it is adjusted properly with no obstructions present and is in clear sight. - ALWAYS keep a moving door in sight until it’s completely closed. - NEVER cross the path of a moving door. Drywall Anchor Screw #6 x1” Min. 5 feet (1.5m) above floor Fig. 1 Connecting Speaker and Door Control Console The Speaker and Door Control Console is a wired, illuminated door and Bluetooth device control with speakers To install the Speaker and Door Control Console: 1. Inside your garage, install the back plate of the Speaker and Door Control Console within sight of the door at a minimum height of 5 feet (1.5m) off the ground. Ensure it is installed out of the reach of children and free from the moving parts of the door and hardware. 2. Fasten it to a solid surface with 1” screws. If attaching to drywall or other hollow surface, drill 3/16” holes and use the provided Drywall Anchors. 3. Snap the Speaker and Door Control Console onto the back plate. To Connect the Speaker and Door Control Console Connect the plug from the Speaker and Door Control Console to the “Wall Panel” outlet on the rear of the Opener, as shown in Fig.2. Fig. 2 UNLOCK Speaker and Door Control Console (ONLY after installation is completed ) Door — Press and release to access the door Light — Turns the courtesy light On/Off Wall Panel 1 2 Check illumination after connecting power Speaker and Door Control Console LOCK Vacation Lock Unlock — Door can be accessed by either Door button or controls Lock — Prevent access of door by any controls and Door button. From Speaker and Door Control Console
15 Trouble-shooting Unit doesn't respond - If the unit appears to be “frozen” or locked up, you may need to reset it. To do so, unplug the power of GDO and re-plug. - Once reset, you will need to adjust them and re-pair with your Bluetooth devices. Music Playback Controls Play/Pause / Phone - Music Playback - Speakerphone - Momentary press - Next song Constant press - Volume up - Momentary press - Previous song Constant press - Volume down ! WARNING To prevent SERIOUS INJURY or DEATH from electrocution: - Power MUST NOT be connected until instructed. To prevent SERIOUS INJURY or DEATH from using the Speaker and Door Control Console or Push Button and a closing door: - Install the Speaker and Door Control Console or Push Button within sight of the door at a minimum height of 5 feet (1.5m) above the floor. Make sure it is out of the reach of children and moving parts of door and hardware. - NEVER permit children to access the Speaker and Door Control Console , Push Button or Remote Controls. - Operate the door ONLY when it is adjusted properly with no obstructions present and is in clear sight. - ALWAYS keep a moving door in sight until it’s completely closed. - NEVER cross the path of a moving door. Bluetooth Music Playback / Hands free Features Pairing using Bluetooth: 1. Enable on handheld device 2. Press and hold button on the wall control until it flashes 2. Search and choose "GUARDIAN" on handheld device 3. Flashing indicator on wall console will glow steadily as confirmation and your music will be played through the opener speakers. MIC
16 ! WARNING To prevent SERIOUS INJURY or DEATH from electrocution or fire: - Power MUST be DISCONNECTED BEFORE proceeding with permanent wiring procedures. - Garage Door Opener installation and wiring MUST be in compliance with all local electrical and building codes. Make sure the Opener is ALWAYS grounded. - NEVER use an extension cord, 2-wire adapter or modify the power plug in any way to make it fit the outlet. Connecting Power To Align the Photo Eye Safety System: 1. When the Photo Eye System is properly connected and the power is connected, one of the Photo Eyes will emit a steady green light. This Photo Eye is the Emitter that generates the Invisible Light Beam. 2. When properly aligned, the Sensor should emit a steady red light when it senses the invisible light beam from the Emitter. 3. If the indication is unsteady, flashes or is dim, check for any obstructions and adjust the position until the Sensor gives a STEADY RED LIGHT. Note: The path of the invisible light beam MUST NOT be obstructed. No part of the garage door or any hardware should interfere with the beam or the Opener will not close the door. Aligning the Photo Eye Safety System To prevent SERIOUS INJURY or DEATH from a closing garage door: - The Photo Eye Safety System MUST be installed BEFORE connecting power. - The Photo Eye Safety System MUST be properly connected and aligned BEFORE operating the Opener. ! WARNING Invisible Light Beam Ordinary Power Connection For Permanent Wiring ONLY Conduit with wire Yellow (from Motor) White (from Light) Neutral (White) Wire nut (Not provided) White (from Logic Board) Line (Black ) Ground (Green/Yellow) Black (from Logic Board) Ground Screw (Green) DO NOT OPERATE OPENER AT THIS TIME. To Connect Power Plug the Opener into a grounded outlet ONLY. If there is no grounded outlet present, call a qualified electrician to replace the outlet. Use of a surge protector is highly recommended. Permanent Wiring (If Required by Local Code) 1. Remove the enclosure by removing the 6 screws located on the sides and rear of the Opener. 2. Cut the two cable pressure connectors connecting line (black) and neutral (white) wire from the power cord. 3. Remove the grounding screw connecting the green wire. 4. Remove the power cord. 5. Group neutral (white) wires from power source with 2 white wires from light cable, and logic board, and yellow wire from motor, inside the Opener. Connect them with a wire nut. 6. Group line (black) wires from power source with another black wires from logic board inside the Opener. Connect them with a wire nut. 7. Secure the ground (green or bare) wire from the power source with a grounding screw. 8. Reinstall the enclosure. 9. Turn on power supply. If the wiring is properly connected, a “click” should be heard and the light will illuminate (if a bulb is installed). If there is no response from the Opener, check power source and wiring.
17 ! WARNING To prevent SERIOUS INJURY or DEATH from improper Force Adjustment: - DO NOT adjust force to compensate for binding or sticking of the garage door. Call a qualified garage door service person to make necessary adjustments in case of binding. - DO NOT increase force beyond minimum force required for closing the door. Too much force will cause improper operation of safety reversal mechanism. - After ANY adjustments, Safety Reverse Test MUST be performed to ensure the door reverses on con-tact with a 1.5” high object (2x4 laid flat). Travel Limit Adjustment— I. UP Limit x1 UP DOWN FORCE LIMIT UP DOWN UP DOWN FORCE LIMIT UP DOWN Desired UP limit Flashes and off I. Setting UP Limit UP DOWN FORCE LIMIT UP DOWN OK 1 2 3 4 About Travel Limit Adjustment Limit Adjustments regulate the fully-open (UP limit) position and fully-closed (DOWN limit) position at which the door will stop when opening and closing. Make sure the trolley is engaged before proceeding adjustments. I. Setting UP Limit 1. Press “LIMIT” button once to enter Travel Limit Adjustment. “UP” indicator (green) is on*. *NOTE: Once you have pressed and released the “Limit” button, the “UP” light will stay for 10 seconds for you to press the “UP” button and begin programming. If the “UP” light goes out before you are finished you need to start over. 2. Press & hold the “UP” button, the door travels up. You may use both “UP” or “DOWN” buttons to inch-adjust the door to the desired UP limit position. 3. Make sure there is enough clearance for your vehicle(s), and there is a minimum 2“ (5cm) gap between Trolley and Stop Bolt. 4. Once the door is at the desired UP limit position, press “LIMIT” button once, “OK” indicator (orange) flashes and goes off. The UP limit is set. NOTICE: This opener will not work until you set the travel limits and the travel force adjustment. The opener will beep 5 times if it is operated without program-ming. Stop Bolt Trolley Minimum 2” (5cm) clearance
18 ! WARNING To prevent SERIOUS INJURY or DEATH from improper Force Adjustment: - DO NOT adjust force to compensate binding or sticking of the garage door. Call a qualified garage door service person to make necessary adjustments in case of binding. - DO NOT increase force beyond minimum force required for closing the door. Too much force will cause improper operation of safety reversal mechanism. - After ANY adjustments, Safety Reverse Test MUST be performed to ensure the door reverses on contact with a 1.5” high object (2x4 laid flat). Travel Limit Adjustment— II. DOWN Limit Desired DOWN limit Flashes and off II. Setting DOWN Limit UP DOWN FORCE LIMIT UP DOWN UP DOWN FORCE LIMIT UP DOWN OK x2 UP DOWN FORCE LIMIT UP DOWN x1 1 2 3 CAUTION: WHILE SETTING THE DOWN LIMIT, CAREFULLY WATCH DOOR TRAVEL DISTANCE. RELEASE BUTTON WHEN THE DOOR MAKES CONTACT WITH THE GROUND! II. Setting DOWN Limit 1. Following UP limit setting, press “LIMIT” button twice to enter DOWN-limit setting. “DOWN” indicator (red) is on*. *NOTE: Once you have pressed and released the “LIMIT” button, it will stay for 10 seconds for you to press the “DOWN” button and begin programming. If the “DOWN” light goes out before you are finished you need to start over. 2. Press & hold the “DOWN” button, the door travels down. You may use both “UP” or “DOWN” buttons to inch-adjust the door to the desired DOWN limit position. 3. Once the door is at the desired DOWN limit position, press “LIMIT” button once, “OK” indicator (orange) flashes and goes off. DOWN limit is set. Both “UP” and “DOWN” (green and red) indicators are now on, indicating that both UP and DOWN limits are set, and the opener is ready for Auto Force Adjustment, see Page19. NOTICE: The opener will not work until you set the travel limits and the travel force adjustment.
19 ! WARNING To prevent SERIOUS INJURY or DEATH from improper Force Adjustment: - DO NOT adjust force to compensate binding or sticking of the garage door. Call a qualified garage door service person to make necessary adjustments in case of binding. - DO NOT increase force beyond minimum force required for closing the door. Too much force will cause improper operation of safety reversal mechanism. - After ANY adjustments, Safety Reverse Test MUST be performed to ensure the door reverses on contact with a 1.5” high object (2x4 laid flat). Auto Force Adjustment Following limit-setting, the unit is now ready to automatically adjust the forces for opening and closing the door. Proceed with the following steps to complete adjustment. 1. With both “UP” and “DOWN” indicators are on after Travel Limit Adjustment, press the “FORCE” button once to enter Auto Force Adjustment. 2. The door will travel up automatically (I) and stop at UP limit for 2 seconds (II). Door will then travel down automatically (III) and stop at down limit (IV). 3. The “OK” indicator (orange) will flash with beeps, the Auto Force Adjustment is completed. 2s Stops at DOWN limit Travels up Stops at UP limit for 2 seconds Travels down I II III IV x2 Flashes OK x1 UP DOWN FORCE LIMIT UP DOWN 1 2 3 Auto Force Adjustment
20 Final Adjustments and Testing Testing the Safety Reverse System The Safety Reverse System prevents the door from closing when an obstruction is present. 1. Open the door by using the Speaker and Door Control Console. 2. Place a 1-1/2” (3.8cm) thick solid object (or 2x4 laid flat) on floor under the center of garage door. 3. Keeping the door in sight, use the Speaker and Door Control Console to close the door. 4. The door MUST REVERSE and beep within 1.5 seconds upon striking the object , and stop at the fully open position. 5. The Safety Reverse System works properly and the opener is ready to use. If the door fails to reverse upon contact with obstruction, adjust the Opener as follows: The close travel may be inadequate, slightly increase the DOWN limit. (See Travel Limit Adjustment on page 17-19) Conduct the test again. If the door reverses on contact, remove the object and run at least 3 COMPLETE travel cycles to ensure proper adjustment. If the Opener still fails the Safety Reverse Test, call a qualified technician for door adjustment. Testing the Photo Eye Safety System 1. Open the door by using the Speaker and Door Control Console. 2. Make sure both Photo Eyes steadily emit the green and red indicator lights. (If not, check alignment) 3. Place an object under the door about 8” (20cm) high by 12” (30cm) wide (the opener carton can be used), 4. The green indicator light on the emitter eye should flash. 5. The red indicator light on the sensor eye should be dimmed. 6. Keep the door in sight and use the Speaker and Door Control Console, Push Button or Control to try to close the door. 7. The door should NOT move more than 1” (2.5cm) and the opener will beep. 1-1/2” (3.8cm) thick solid object (or 2x4 laid flat) Travels up Travels down 1 3 4 2 Door reverses and beeps upon strike OFF Flashes Beeps and reverses upon obstruction x20 Sensor Emitter GREEN LIGHT RED LIGHT ! WARNING To prevent SERIOUS INJURY or DEATH from a closing garage door: - The Safety Reversal Test MUST be conducted ONCE A MONTH. - NO ONE should cross the path of moving door during operation and/or testing. - If either Force or Travel limit adjustment is made, then other adjustment may also be needed. - After ANY adjustments to the door system, the Safety Reverse Test MUST be performed to ensure the door reverses on contact with a 1-1/2” thick (2x4 laid flat) object. - The Photo Eye Safety System MUST be properly aligned, and tested regularly.
21 ! WARNING To Prevent SERIOUS INJURY or DEATH: - Keep remote control and battery out of reach of children. - NEVER permit children to access the Speaker and Door Control Console, Push Button nor Remote Controls. - Operate the door ONLY when it is properly adjusted, and there are no obstructions present. - ALWAYS keep a moving door in sight until completely closed. NEVER cross the path of a moving door. To reduce risk of fire, explosion or electric shock: - DO NOT short circuit, recharge, dissemble or heat the battery. - Replace with 23AE 12 Volt batteries ONLY. Dispose of batteries properly. Programming Remote Controls To Program Remote Control (s): 1. Press/release the “LEARN” button once on the rear control panel, “OK” LED will glow and beep. The unit is now ready to accept a remote control in the next 30 seconds as shown in Fig.2. 2. Press/release any desired button on the Remote Control. 3. The “OK” LED will flash and beep twice indicating Remote Control is stored successfully. Up to 20 Remote Controls (including wireless keypad codes) can be added to the unit by repeating the above procedures. If more than 20 Remote Controls are stored, the first stored Remote Control will be replaced. (i.e. the 21st Remote Control replaces the 1st stored Remote Control .) Removing ALL Remote Controls: To remove ALL Remote Controls from memory, press and hold the “LEARN” button for 5 seconds. The “OK” LED will flash and beep 2 times indicating. ALL Remote Controls have been removed from memory. Replacing Remote Control Battery: When the battery of the Remote Control is low, the indicator light will become dim and/or the range of the Remote Control will decrease. To replace the battery, remove the battery cover from the Remote Control and replace with a 23AE 12 volt alkaline battery with polarity shown in Fig.3. This device complies FCC Rules for HOME OR OFFICE USE. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Fig.1 Fig.3 Fig.2 LEARN 30 seconds OK 1 Visor Clip Holster Signal and Battery Indicator 2 OK 3 x2 x2
22 ! WARNING To Prevent SERIOUS INJURY or DEATH: - READ AND FOLLOW ALL INSTRUCTIONS AND WARNINGS IN THE OWNER’S MANUAL AND LABELS - Keep Remote Control and battery out of reach of children. - NEVER permit children to access the Speaker and Door Control Console, Push Button or Remote Controls. - Operate the door ONLY when it is properly adjusted, and there are no obstructions and is in clear sight. - ALWAYS keep a moving door in sight until completely closed. NEVER cross the path of a moving door. - If Travel limit adjustment is made, Force Adjustment may also needed. - After ANY adjustments, the Safety Reverse Test MUST be performed to ensure the door reverses on contact with a 1-1/2” thick object (2x4 laid flat). - ALWAYS ensure that your door is balanced and in good working condition. Operating the Opener Emergency Release Handle Photo Eye Safety System Invisible Light Beam Actual Operating Scenario Speaker and Door Control Console Controls Operation Speaker and Door Control Console Momentary press the “DOOR” button on the Door Control Console, the door starts to move, and controls as follows: - Open or close the door. - Reverse the door while it is closing - Stops the door while it is opening. Constant press to close the door when the Photo Eye Safety System is not installed, misaligned or obstructed INTENTIONALLY. Press and hold the button until door is fully closed. Remote Control Remote distance up to 200ft. in open field. For safety concerns, the Remote Control WILL NOT work if the Photo Eye Safety System is not properly installed and aligned. Wireless Keyless Entry Keypad* Program the Wireless Keyless Entry Keypad accordingly and access the door using the PIN code. Activating the Opener Attach the protective cover to the opener after installation and adjustment is completed. *Optional
23 Door Status vs. Activation ! WARNING To Prevent SERIOUS INJURY or DEATH: - Use Emergency Release to disconnect Trolley ONLY when the door is CLOSED to prevent unexpected rapid falling in case of a unbalanced / poor-conditioned door. - Use Emergency Release ONLY when doorway is clear of persons and obstructions. - DO NOT use Emergency Release to pull the door open or closed. In case of a power failure or door obstruction, PULL EMERGENCY Handle to release door from Opener. To Disconnect Trolley for Manual Operation With the door closed, pull down the emergency release handle to the DISCONNECT position. The door can be raised / lowered manually. To Re-connect Trolley Pull the Handle toward the Opener so that the lever will flip up to the CONNECT position. The Trolley will reconnect itself when the Opener is activated or when the door is manually opened/closed. Lever CONNECT DISCONNECT Pull to Disconnect Flip to reconnect Manual Operation Door status Activation using Speaker and Door Control Console / Remote Control Door at fully open / close position Door will move to fully close / open position Door is closing Door will reverse Door is opening Door will stop Door is stopped as intended in partially open position Close Door is obstructed while closing Door will reverse while flashing courtesy light Door is obstructed while opening Door will stop Door is fully opened and Photo Eye System is obstructed Door will not close Operating the Opener Operation / Condition Opener is initially plugged-in (no travel limits stored) Flash x 5 Reconnecting power (with travel limits stored) Flash x 3 “LEARN” button is pressed Beep x 1 Upon activation Light On for 4.5 minutes Upon activation by remote controls Beep x 1, Light On for 4.5 minutes Remote Control / Keyless Entry PIN code accepted Beep x 2 Opener is operated without programming Beep x 5 Door travels with abnormal speed Beep x 12 (1 beep / second) Photo Eye System is obstructed during door-closing Beep x 20 The door is obstructed during travel Beep x 25 Courtesy Light / Buzzer Responses Courtesy Light / Buzzer Responses
24 Problem Possible Cause / Solution Opener does not open or close and beeps 5x Reprogram the operator. See pages 17-19. Opener does not respond to Remote Control - Refer page 21 to reprogram Remote Control. - Check Remote Control battery. Opener stops before reaching full open / close position Travel Limit is not properly adjusted. This could also be force related. Check adjustment or reprogram referring to pages 17-19. Conduct Safety Reverse Test after ANY adjustment. The door reverses unintentionally - Make sure the Photo Eye Safety System is aligned and clear of obstructions. - If door is replaced or door condition has significant changes, - Refer to page 4 to check the door balance - Refer to page 17-19 to re-adjust Travel Limits and Travel Force. The door reverses upon touching the floor and the courtesy light flashes Refer to page 17-19 to reset Travel Limits and Travel Force. The Opener does not close the door and the indicator on one of the Photo Eyes flashes The Photo Eye Safety System is misaligned or obstructed, refer to page16 for proper alignment. The Opener is working properly but the courtesy light does not turn on Replace light bulb (A19 incandescent Max.100W). The courtesy light does not turn off Light relay is stuck. Tap relay on the board to free contact or replace logic board. Schedule Maintenance Once a month Door balance test, refer to page 4. Safety reverse test, refer to page 20. Twice a year Check chain/belt tension ( refer to page 6 for adjustment if necessary). Once a year - Limit and Force adjustment may be necessary due to weather conditions. Refer to pages 17-19 for adjustment. Conduct Safety Reverse Test after ANY adjustments. - Lubricate door rollers, bearings and hinges. The Opener is permanently lubricated, DO NOT lubricate or grease the Opener, rail or door tracks. Maintenance Red Green LED Green LED Green LED Green LED Red LED Green LED Red LED Red LED Green LED Red LED Red LED Note: If installing operators on two doors in the same garage, to ensure proper operation, Photo Eyes should be aligned as below: Troubleshooting See additional trouble shooting tips on the www.adhguardianusa.com website.
25 Installation Parts Accessories Item Part No. Name / Description 1 GUAT-027 Header Bracket 2 GUAT-022 Door Bracket 3 GUAT-023 Hardware Bag (Installation hardware shown on P.3) 4 GUAT-024 Curved Door Arm 5 GUAT-025 Straight Door Arm 6 GUAT-026 Emergency Release Handle & Rope Item Part No. Name / Description 1 GUAT-201 Photo Eye Safety System (Emitter + Sensor with Brackets) 2 GDOR2B Remote Control 3 GUDT-203 12V AE23 Alkaline Battery 4 GUDT-212 Speaker and Door Control Console 5 GUDT-213 Owner’s manual 1 2 3 4 5 6 1 2 3 5 Repair Parts 4
26 Opener Assembly Parts Item Part No. Name / Description 1 GUDT-301 Chassis 2 GUDT-302 Transformer 3 GUDT-312 Logic Board 4 GUDT-313 DC Motor (with encoder shaft) 5 GUDT-314 Encoder Module 8 GUDT-324 Opener Cover 9 GUDT-309 Lamp Plate 10 GUDT-310 Light Lens Cover 11 GUDT-311 Light Lens Clip 13 GUDT-327 Speaker Unit 12 GUDT-325 Bluetooth & Amplifier Board 1 2 4 3 9 8 10 11 5 12 13
27 FCC Statement Manufacturer hereby warrants: Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’sauthority to operate the equipment. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator& your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 ofthe FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a Residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful Interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference toradio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio technician for help.
Manufacturer hereby warrants: 1. Garage Door Operators to be free from defects in material and workmanship for a period of five (5) years for motors and one (1) year for Electronics and Mechanics from date of purchase, if installed by an authorized reseller, otherwise if installed by the purchaser one (1) year will apply. 2. Garage Door Operators (Commercial and Industrial Application) to be free from defects in material and workmanship for a period of three (3) months from date of purchase. 3. Where the garage door operator has been returned to the manufacturer for Warranty repairs, all costs incurred in the return will be paid for by the purchaser. If in the opinion of the manufacturer the product is faulty, all defective parts will be replaced at no charge to the purchaser. 4. Proof of purchase must be given to the manufacturer at time of Warranty claim. 5. The manufacturer reserves the right to modify any existing or future products without incurring any obligation to incorporate such modification to products already manufactured or to which this Warranty may relate. 6. Warranty only applies if this product has been installed to the Manufacturers recommendation 7. This Warranty does not apply to any defect, loss or damage arising or caused directly or indirectly by or as a result of : (i) Any defect (including detects in component parts or accessories) arising from or attributable to the failure to carry out normal preventive maintenance or adjustment itself. (ii) To any additional damage or deterioration arising from attributable to the operation of the Operator after it is known to be defective. 8. Exclusions to Warranty Period: (i) Repair or Warranty Work - three (3) month 9. Not included in Warranty: (i) Batteries. (ii) Fuses. (iii) Light bulbs. (iv) Sensitivity adjustment. (v) Handheld Remote Controls and receiver range. 10. Note : All Warranties will be void subject to: (i) Water damage and condensation. (ii) Power supply black out or surge. (iii) Act of God. (iv) Modification or adjustment by unauthorized persons. (v) Any interference from radio (including citizen band radios or and other electronic device) (vi) Preventative maintenance and regular servicing not undertaken. (vii) Account not paid in full by the purchaser. 11. Subject only to the provisions of the Trade practices Act and any legislation of the State or Territory wherein the operators of the Manufacturer have been sold or installed (which may confer certain rights on consumers of goods and those rights by such legislation may be rendered incapable of exclusion) this Warranty supersedes and excludes all representations, warranties and conditions whether expressed or implied by law and the Manufacturer shall have no liability or otherwise than herein provided for any loss and damage (including consequential loss and damage, loss of use or profits) by reasons of delay, defective or faulty materials or workmanship, negligence or any act, matter or thing done permitted or omitted to be done by the Manufacturer. WARRANTY THIS WARRANTY FORM SHOULD BE COMPLETED AT TIME OF INSTALLATION This Warranty Form should be retained by the purchaser at all times and produced with the purchase docket by the Purchaser as proof of the purchase date. PURCHASER’S NAME: PURCHASER’S ADDRESS: INSTALLED BY: INSTALLER’S ADDRESS: INSTALLER’S SIGNATURE: SERIAL NUMBER OF THE OPERATOR: GUARDIAN SERVICE Your operator has been installed by a professional installation specialist. If service information is required please contact the installing company or your local Guardian dealer. Look for your Guardian dealer online, in the yellow pages or call our service number for a dealer near you. Service number : 1-424-272-6998 Please have the following information when you call: ·Model number of the operator ·Serial number of the operator--located on the bar code label on top of the opener, above the adjustment buttons WARRANTY GARAGE DOOR OPERATORS

Navigation menu