GN Audio USA SERIES9200 Series 9200 Bluetooth Wireless Headset User Manual THOR SERIES 9200 USERS MANUAL Revised

GN Netcom Inc Series 9200 Bluetooth Wireless Headset THOR SERIES 9200 USERS MANUAL Revised

users manual

SERIES 9200 BLUETOOTH WIRELESS HEADSETUSERS MANUAL(July 2001, Preliminary)GN Netcom Inc77 Northeastern Blvd.Nashua N.H. 03062
Series 9200 Bluetooth Wireless Headset IntroductionThe Series 9200 Headset is a lightweight “over the ear” wireless headset utilizing Bluetooth technology inthe 2.4 GHz band for a short range (up to 10 meters) RF link. The headset contains a microphone and areceiver, and is intended for hands free communications with mobile telephones containing Bluetoothcompatibility or any other device that has a Bluetooth Audio Gateway.Headset power is provided by a rechargeable battery. The battery can be charged with a vehicular chargeadapter or an AC charge adapter. Battery Life is approximately 3 hours {“Talk Time”) and 100 hoursstandby (“Sniff”) timeThe headset has the following user operated controls (see Figure 1):1. Boom Switch---The power is OFF when the microphone boom is in the closed position and the poweris ON when the microphone boom is in the open position.2. Function Button---This button is pushed for various lengths of time to initiate a call, hang up a call,pairing, transferring a call to a headset, and microphone mute.3. Volume Rocker Switch---The upper portion of this switch is pushed momentarily to INCREASE thereceive volume in steps and the lower portion of this switch is pushed momentarily to DECREASE thereceive volume in steps.The headset has the following visual indicator: Blue LED at tip of microphone boom---LED flashes at various rates and durations to indicate PowerON/OFF, Charging, Search & Pairing, BT Link Established, Standby/Sniff Mode, and Audio Link (on acall)The headset has the following audio indicator:Tone in receiver---Tone varies in duration, duty cycle and frequency to indicate Volume Steps, VolumeMin, Volume Max, Low Battery, Microphone Mute, Incoming Call, and Pairing
I Series 9200 Bluetooth Headset Operation---Preliminary1. The battery must be charged before using.2. To charge battery plug charger connector into rectangular Charge Jack located on edge of housingopposite microphone boom hinge. (Note that the headset is not functional while charging and themicrophone boom can be open or closed). Select 4-hour charge rate on charger and charge battery. TheBlue LED in the tip of the microphone boom will stay ON during charging and go OFF when chargingis complete (and the charger is still plugged in).3. The headset is supplied for use on the right ear. For left ear use open the ear loop 90 degrees from theclosed position, carefully snap ear loop off of hinge, rotate 180 degrees and snap back onto hinge.II Pairing with Mobile Phone (Mobile phone must be Bluetooth compatible.)(Note: The Auto Pairing Mode will be entered when the boom is opened if not already paired. Pairing mustbe done every time the headset establishes a link with a different mobile phone or other Bluetoothcompatible device)1. Verify power of mobile phone to be paired with is ON and phone is within 10 feet of headset.2. Open headset microphone boom to switch headset power ON.3. Within 3 seconds after the microphone boom is opened press the Function Button for 2 seconds.4. Note that the Blue LED will flash ON & OFF for ½ second durations until the Bluetooth pairing hasbeen completed. When pairing has been completed the Blue LED will go ON steady for 5 secondsfollowed by a series of 10 rapid flashes. Also, a ½ second 2 kHz beep will be heard from the receiver.5. To establish an Audio Connection with mobile phone after pairing: Select Settings, Connection,Bluetooth Link, Handsfree, and Scan All on mobile phone. Enter Headset PIN # (xxxx) whenprompted. Select Link on phone to establish Audio Connection.6. If pairing fails, the Blue LED will go OFF.III Receiving an Incoming Call1. Place the headset on your ear after opening the microphone boom fully, opening the ear hook 90degrees, placing the earhook over your ear, and close the earhook so the receiver is close to your ear.The microphone boom should be pointed toward your mouth.2. If there is an incoming call while the headset boom is open and the devices are paired, the call willautomatically be answered by the headset. When on a call, the Blue LED will flash at a rate of 1second ON and 1 second OFF.3. If the BT link has been established and the headset is in “Sniff Mode” (The headset is powered up forapproximately 5 minutes after opening the boom and approximately 5 minutes after a call iscompleted, then it goes into “Sniff Mode” to conserve battery life. The Blue LED blinks at a rate of1/10 second ON and 2.9 seconds OFF when in “Sniff Mode”.), an incoming Call Alert can be
answered by pressing the Function Button momentarily. (The Incoming Call Alert is 1 second of 700Hz Warble Tone.)4. To adjust the Receive Volume Up, momentarily press the upper end of the rocker switch one or moretimes until the desired level is achieved. A ½ second 2 kHz beep will be heard when the max volume isreached.5. To adjust the Receive Volume Down, momentarily press the lower end of the rocker switch one ormore times until the desired level is achieved. A ½ second 2 kHz beep will be heard when the minvolume is reached.IV Making an Outgoing Connection1. If the headset is powered up, dialing can be done from the cell phone or by Voice Dialing if available2. If the headset is in the “Sniff Mode” press the Function Button for more than 2 seconds and release.Dialing can be done from the cell phone or by Voice Dialing if available.VI Other Functions1. Microphone Mute can be accomplished while on a call by momentarily pressing the Function Buttonto mute and un-mute. When the microphone is muted, two 150 millisecond 2 kHz beeps are heard inthe receiver every 15 seconds.2. Low Battery Warning is indicated by five 50 millisecond 2 kHz beeps in the receiver every 20 seconds.3. Out of Range is indicated by deterioration of audio quality (noisy signal) in the receiver.4. Power ON/OFF is accomplished by opening and closing the microphone boom.VII Storage1. Always store with microphone boom closed (Power OFF) and in a cloth or plastic bag to keep dust andlint out of microphone and speaker openings.2. Avoid storage at high temperatures (above 60 C or 134 F), such as in a hot vehicle in direct sunlight.Storage at high temperatures can degrade performance and reduce battery life.3. Do not expose headset to rain or other liquids.VIII Parts Replacement1. Battery: This product is equipped with a Lithium Rechargeable Battery. Replacement must be done ata qualified service center or returned to the manufacturer. Use only P/N xxxxxx battery2. AC Charger: Use only P/N xxxxxx3. Vehicular Charger: Use only P/N xxxxxxIX Certification and Safety Approvals for Series 9200 Bluetooth Wireless Headset
1. FCC: This product has been tested to comply with FCC Standards and is For Home or Office Use.This product complies with FCC Part 15 as a Class B Computing Device. The FCC I.D. is xxxxxx2. UL: This product is UL Listed ITE and complies with UL 60950, Canada and US. The UL FileNumber is E210538.Note: A label with essential FCC and UL information is located in the battery compartment.FCC Notice to UsersThis device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and (2) this device must accept any interferencereceived, including interference that may cause undesired operation.FCC Information to UserChanges or modifications not expressly approved by the party responsible for compliance could void theusers authority to operate the equipment.WarrantyGN Netcom, Inc warrants this product against all defects in material and workmanship for a period of oneyear from the date of original purchase. The conditions of this warranty and our responsibilities under thiswarranty are as follows:• The warranty is limited to the original purchaser.• The warranty is void if the serial number, date code label or product label is removed, or if the producthas been subject to physical abuse, improper installation, modification, or repair by unauthorized thirdparties.• The responsibility of GN Netcom, Inc products shall be limited to the repair or replacement of theproduct at the sole discretion of GN Netcom, Inc.• Any implied warranty on GN Netcom, Inc. products is limited to one year from the date of purchase onall parts, including the cords and connectors. Specifically exempt from any warranty are limited-lifeconsumable components subject to normal wear and tear, such as microphone windscreens, earcushions, ear tips, decorative finishes, batteries, and other accessories. GN Netcom, Inc. is not liablefor any incidental or consequential damages arising from the use or misuse of any GN Netcom, Inc.product.• A copy of your receipt or other proof of purchase is required. Without proof of purchase, yourwarranty is defined as beginning on the date of manufacture as labeled on the product.• This warranty gives you specific rights and you may have other rights which vary from state to state.
Unless otherwise instructed in the User Guide, the user may not, under any circumstances, attempt toperform service, adjustments or repairs on this unit, whether in or out of warranty. It must be returned tothe factory or authorized service agency for all such work.To Obtain ServiceFor customer service and technical support, call GN Netcom, Inc. at 1-800-826-4656If it becomes necessary to send a unit in for repair, it is not necessary to call for a Return MaterialAuthorization (RMA) number, as one will be assigned upon receipt of the package at the factory.Ship the product in a suitable shipping container, fully insured and with the shipping charges prepaid.Include the following with the product:• Your name, company name, address and telephone number.• A description of the problem.• A copy of the receipt or other proof of purchase is requested for in warranty products (without proof ofpurchase, your warranty will be defined as beginning on the date of manufacture as labeled on theproduct.)• For out of warranty products, send a purchase order which authorizes repair.In warranty products are warranted for the remainder of the original warranty period. Out of warrantyproducts will be repaired or replaced at the prevailing charge and carry a one-year warranty from the repairdate.GN Netcom, Inc will not assume any responsibility for any loss or damage incurred in shipping. Any repairwork on GN Netcom, Inc. products by unauthorized third parties voids any GN Netcom. Inc. warranty.Ship to: GN Netcom, Inc.77 Northeastern Blvd.Nashua, NH 03062

Navigation menu