GE MDS DS-TD220 Narrowband Wireless Transceiver User Manual Book1

GE MDS LLC Narrowband Wireless Transceiver Book1

Contents

User manual

 Start-Up Guide  Firmware Release 1.x.x MDS 05-4818A01, Rev. 02OCTOBER 2008DRAFT MDS TD 220 217–222 MHz Data Transceiver
 OPERATIONAL & SAFETY NOTICES Concentrated energy from a directional antenna may pose a health hazard to humans. Do not allow people to come closer to the antenna than the distances listed in the table below when the transmitter is operating. More information on RF exposure can be found online at the following website:www.fcc.gov/oet/info/documents/bulletins. Above data based on a 30-watt output level with a 100% duty cycle. FCC Part 15 Notice The transceiver is approved under Part 15 of the FCC Rules. Operation is subject to the following two con-ditions: (1) this device may not cause harmful interference, and (2) this device must accept any interfer-ence received, including interference that may cause undesired operation. Any unauthorized modification or changes to this device without the express approval of Microwave Data Systems may void the user’s authority to operate this device. Furthermore, this device is intended to be used only when installed in accordance with the instructions outlined in this manual. Failure to comply with these instructions may void the user’s authority to operate this device. Antenna Gain vs. Recommended Safety Distance Device complies with Power Density requirements at 20 cm separation:NoRequired separation distance for 9 dBi antenna (in m): 2.53RF Exposure
 05-4819A01, Rev. 01 TD220 Installation/Operation Guide 1 INTRODUCTION This guide presents basic installation and operating instructions for the GE MDS TD 220 Series wireless transceiver.The TD 220 operates in two bands and power levels:• 25-Watts in the 220-222 MHz range• 2-Watts in the 217-220 MHz rangeThe radio is a GMSK unit intended for bridging ITCS messages over the air between locomotives and wayside devices. The data interface is Ethernet, with UDP-encapsulated ITCS message payload. Figure 1. TD 220 Data TransceiverNOTE: Some features may not be available on all units, based on the options purchased and the applicable regulatory constraints for the region in which the radio will operate.Each second is divided into 8 133-byte time slots. The first of the 8 timeslots each second is always reserved for bases to transmit beacon information to the mobiles in the area. Following the beacon are 4 (or 5) time slots that are always reserved for mobiles to transmit. At the end of each second, are 3 (or 2) time slots that can be used by bases or mobiles. These slots are used with the following priority: the previous base, the current base, and then mobiles. In other words, during second 1 in the table below, base A actually has priority over the last three slots. If A does not use them, B can use them. If B does not use them, mobiles can. Bases reserve these time slots with flags in the beacon. This scheme maximizes the potential for utilizing all slots.
 2 TD220 Installation/Operation Guide 05-4819A01, Rev. 01  DATA INTERFACES DB-25 Figure 10 shows the pin arrangement for the DB-25  DATA INTER-FACE  connector. Table 1 lists the pin functions and shows input/output data for the connector. Invisible place holder Figure 2. DB-25 Pin Arrangement (As viewed from outside the radio) Table 1. Data Interface Pinouts Pin No. Signal Name and Description Input/Output 1 COM3_DCD —Reserved. Input2 COM2_TXD —Descriptive text to be supplied. Input3 COM2_RXD —Descriptive text to be supplied. Output4 COM2_RTS —Descriptive text to be supplied. Input13121110987654321242322212019181716151425
 05-4819A01, Rev. 01 TD220 Installation/Operation Guide 3 USB The radio provides a USB Port conforming to version 1.1 of the USB standard. This port is provided for future features such as ITCS log-ging to text files on a memory stick. Consult GE MDS for information on this feature. The pinout for this connector is given in the table below. 5 COM2_CTS —Descriptive text to be supplied. Output6 COM3_TXD —Reserved. Output7 Ground —Descriptive text to be supplied. --8 COM2_DCD —Descriptive text to be supplied. Output9 COM3_CTS —Reserved. Input10 COM3_RTS —Reserved. Output11 COM3_DTR —Reserved. Output12 COM3_RXD —Reserved. Input13 Ground —Descriptive text to be supplied. --14 ETH_TX_H —Descriptive text to be supplied. Output15 ETH_TX_L —Descriptive text to be supplied. Output16 ETH_RX_H —Descriptive text to be supplied. Input17 ETH_RX_L —Descriptive text to be supplied. Input18 EXT_Key —Reserved. Output19 EXT_DET —Reserved. Input20 COM2_DTR —Descriptive text to be supplied. Input21 ALARM_OUT —Reserved. Output22 GPS_PPS_L For TTL PPS, leave this pin open.Input23 GPS_PPS_H For TTL PPS, use this input.Input24 COM1_RXD —Descriptive text to be supplied. Input25 COM1_TXD —Descriptive text to be supplied. Output Table 1. Data Interface Pinouts
 4 TD220 Installation/Operation Guide 05-4819A01, Rev. 01  Power The power connector is a screw-secured 2-pin connector.The pin orientation (as looking into the connector) is shown below.The following table shows how much current is required for receiving or transmitting vs. input voltage and RF power output. Table 2. USB Connector Pinouts Pin Signal Name Description 1 PC_USB_+5V +5 VDC2 USBD- USB Data Minus3 USBD+ USB Data Plus4 GROUND Chassis Ground Table 3. Power Connector Pinouts Pin Signal Name Input/Output Description 1(Left)PWR Input 13.8 Vdc input, 7A maximum2(Right)GROUND Input Power return Table 4. Current/Voltage Requirements vs. RF Output Voltage (Vdc) RF Output (W) Current Required (A)12 0 (RX) TBSL12 2 TBSL12 10 TBSL12 25 TBSLL  R
 05-4819A01, Rev. 01 TD220 Installation/Operation Guide 5 Antenna Connector The Antenna Connector is a Type-N female connector with 50-Ohm characteristic impedance. Common Setup Tasks Key the Transmitter for Test Purposes 1. Log in to the radio on its COM1 console using a serial terminal emulator program.2. Go to the Radio Configuration menu.3. Select the frequency for the test transmission.4. Select the RF Output Power to use. Note that power levels greater than 2 Watts will timeout after a 5-second period by default. Ensure ventilation with supplemental forced airflow if longer durations are desired.5. Select the Force TX Key menu option.6. When finished, deselect the Force TX Key menu option. Prepare the Network Interface for a Radio Each radio is assigned an IP Address, a Netmask, and a Gateway IP Address. The IP Address and Netmask should be chosen carefully. The radio will network directly with other equipment with IP Addresses that are on a common Subnet. IP Addresses that begin with the same numerical IP address bits where the Netmask is one will be on the same Subnet. For example, if the IP Address is 10.4.100.1 and the Netmask is 255.255.0.0, the radio will attempt direct Ethernet  13.8 0 (RX) TBSL13.8 2 TBSL13.8 10 TBSL13.8 25 TBSL Table 4. Current/Voltage Requirements vs. RF Output Voltage (Vdc) RF Output (W) Current Required (A)
 6 TD220 Installation/Operation Guide 05-4819A01, Rev. 01  communication with any node whose IP Address begins with 10.4. If a message is bound for a node outside of the 10.4 network, it will be sent to the Gateway IP address instead so that it can be placed from the radio's subnet onto another subnet.1. Log in to the radio on its COM1 console using a serial terminal emulator program.2. Go to the IP Configuration menu.3. Set the IP address of the radio, plus the Netmask and Gateway.4. Go to the Maintenance/Tools Menu and select the Ping Utility.5. Enter the IP address of a known node on the network.6. Execute the Ping and observe the results. If the network interface is working properly, Ping responses should be received. Set Up a Base Unit 1. If not already done, complete steps from 3.2 above.2. Log in to the radio.3. Go to the System Configuration menu.4. Set the unit to Base mode and reboot if necessary.5. Set the base type (A, B, or C).6. Set the window size. Mobiles will transmit in a randomly selected available slot among 2^(Window Size) slots. For small networks, this can be 1. For larger networks, use a Window Size that pro-vides double or quadruple the number of mobiles expected under one base at a time.7. Set the IP Port on which the base will receive UDP messages from wayside devices.8. Set up an ITCS Translation Table. For test purposes, this may be as simple as setting up one known address with a mask of all “If’s”.9. Verify Ethernet Link using the Ping utility in the Mainte-nance/Tools Menu.10. Begin sending UDP data.11. Verify the TX LED illuminates and the radio begins transmitting over the air.
 05-4819A01, Rev. 01 TD220 Installation/Operation Guide 7 3.4 Set Up a Mobile Unit 1. If not already done, complete steps from 3.2 above.2. Log in to the radio.3. Go to the System Configuration menu.4. Set the unit to Mobile mode and reboot if necessary.5. Set the IP Port to which the mobile will send messages received over the air.6. Set the IP Port on which the mobile will accept incoming mes-sages for transmission over the air.7. Verify Ethernet Link using the Ping utility in the Mainte-nance/Tools Menu.8. Ensure at least one base is present in the neighborhood of this radio so that it can detect beacons and synchronize timing.9. Begin sending UDP data from a polling program.10. Verify the TX LED illuminates and the radio begins transmitting over the air. 3.5 Perform Test Polling 1. Set up the Base and Mobile as above.2. Connect as shown in the following diagram. Note: this is for bench testing only, i.e. not for sensitivity testing. Sensitivity test-ing requires complete RF isolation or mixed operation to prevent the leakage path from being the dominant RF path between units. For bench testing, use attenuation so that the signal level at every unit that is participating is around -70 to -50 dBm.
 8 TD220 Installation/Operation Guide 05-4819A01, Rev. 01  Invisible place holder Figure 3. Test Setup 3. Configure the Base as follows in the radio software:
 05-4819A01, Rev. 01 TD220 Installation/Operation Guide 9 4. Reboot the Base5. Obtain the Parametric Poller (parm_poller.exe) from GE MDS. This utility saves its settings to  parm_poller.ini  in the current direc-tory, so make one directory for the base and a different directory for the mobile.6. In the base directory, create the parm_poller data configuration file ( parm_poller.parms ) as shown below.
 10 TD220 Installation/Operation Guide 05-4819A01, Rev. 01  set ::parms {  { 0 "Dest"   32 "11223344"     "RW" }  { 1 "Src"    32 "aabbccdd"     "RW" }  { 2 "Flags"  8  "00"           "RW" }  { 3 "Length" l1 "00"           "RO" }  { 4 "Seq No" sn "00"           "RW" }   { 5 "Data"   nt "Hello, World" "RW" }  7. Set up the base parm_poller as shown below, where  10.4.144.100  is replaced with the IP address of your base.
 05-4819A01, Rev. 01 TD220 Installation/Operation Guide 11 8. Configure the Mobile as follows:9. Reboot the Mobile unit.10. Copy the base unit's  parm_poller.parms  file to the mobile direc-tory.11. Set up the mobile  parm_poller  as shown below.12. Click Start Polling on both units and observe the message counts and sequence number increment.13. If additional visibility is desired, obtain  itcslog.exe  from GE MDS. This utility captures messages from the logging output of the TD220 radios and displays statistics about them. The IP Port Number is the port number configured on the radio for ITCS log-ging.
 12 TD220 Installation/Operation Guide 05-4819A01, Rev. 01  Description of Menu Interface Login with user name  admin , password  admin .When logged in, the Starting Information Screen is displayed.
 05-4819A01, Rev. 01 TD220 Installation/Operation Guide 13 R* - This parameter is writable from another menu. Table 5. Starting Information Screen Items Parameter R/W Description Device Name R* User-configured name for this radio. Set this from the Device Names menu.IP Address R* IP Address for this radio. Set this from the IP Networking menu.Device Status R “Initializing” during startup and/or internal RF deck reprogramming, “Operational” when functioning, “Alarmed” when error condition(s) exist.Location R* User-configured location for this radio. Set this from the Device Names menu.Serial Number R The manufacturer's serial number for this radio. Set only in the factory.Uptime R Elapsed time since the radio was started.Current FirmwareR* The version number of the currently operating firmware. Reprogram firmware from the Reprogramming Menu.Current User R Login level
 14 TD220 Installation/Operation Guide 05-4819A01, Rev. 01  Table 6. Main Menu Items Parameter R/W Description A) Starting Information ScreenReturns to the opening menuB) Network Configuration Set the radio's IP Address, Netmask, and GatewayC) System Configuration Set the radio's Mode (Base/Mobile) and other application-specific operating parameters including the Base's ITCS translation table.D) Radio Configuration Set the radio's Frequencies, Base transmit slot allocation (3/4), RF Power Output, and access the Force TX Key function.E) Security Configuration Set up how the radio may be accessedF) Statistics / Logging Obtain historical and current statistics about the radio's payload performance, and access ITCS Logging configuration.G) Device Information Set up the radio's Date, Time, Console Baud Rate and Names. Review the radio's Model, Serial Number, and Uptime.H) Maintenance / Tools Access the radio's Firmware Reprogramming, Configuration Script, and Ping Utility menus.
 05-4819A01, Rev. 01 TD220 Installation/Operation Guide 15 Table 7. Network Configuration Menu Items Parameter R/W Description A) IP Configuration Access the IP Configuration menu to set the IP Address, Netmask, and Gateway IP Address.Ethernet Address R Displays the hardware MAC address for the Ethernet port.
 16 TD220 Installation/Operation Guide 05-4819A01, Rev. 01 Note: The IP Address and IP Gateway must be on the same subnet or a Network Interface error will occur. Table 8. IP Configuration Menu Items Parameter R/W Description IP Address R/W The IP address that this radio will use for its Ethernet interface.IP Netmask R/W The subnet mask for the network this radio is part of.C) IP Gateway R/W The IP address of the gateway that will pass traffic from the radio's subnet to nodes on other networks.
 05-4819A01, Rev. 01 TD220 Installation/Operation Guide 17 Table 9. System Configuration Menu Items Parameter R/W Description A) Unit Type R/W Bases send beacons out once per epoch and coordinate downstream messages. Mobiles listen to bases to identify free slots, and then select random slots in which to place their upstream messages.B) Base Unit Zone R/W Bases are one of three types, A, B, and C. Each base coordinates slots in the epoch assigned to that base and transmits downstream. Base types repeat along lines of track (A, B, C, A, B, …)
 18 TD220 Installation/Operation Guide 05-4819A01, Rev. 01 C) Window Size R/W When a mobile is ready to transmit, it chooses at random from 2^(Window Size) slots to minimize collisions with other units.D) ITCS UDP Receive PortR/W Wayside devices send UDP messages to this IP port on the radio's network interface for transmission over the air.E) Timing Signal Timeout R/W If the GPS Pulse Per Second input is missing for this duration, the radio asserts an alarm.F) ITCS Translation Table -- Access the ITCS Translation Table to add or delete routing entries. Table 9. System Configuration Menu Items Parameter R/W Description
 05-4819A01, Rev. 01 TD220 Installation/Operation Guide 19 The following chart shows how RSSI Data (shaded portion) is prepended to standard ITCS Data within the UDP packet. Table 10. ITCS Translation Table Menu Items Parameter R/W Description A) ITCS Translation Table EntryR/W Each entry in this table contains a 32-bit Destination ITCS Address, a 32-bit ITCS Address Mask, an IP Address and port, and the RSSI Option. Any incoming ITCS message is bitwise anded with the mask. If the result matches the Destination ITCS Address, the message is sent to the IP Address and Port given. If the RSSI Option is “yes”, the over the air Received Signal Strength Indication is prepended to the data message in the UDP transmission. Table 11. RSSI Data in Relation to ITCS Data Non-ITCS Header Data ITCS L2 Header DataAddress ID Length RSSITypeRSSI DataDestinationITCSAddressSourceITCSAddress4 Bytes 1 Byte 1 Byte 1 Byte 1 Byte 4 Bytes 4 Bytes N BytesAlways 00 for RSSI2 0 Signed value from –120 to –30 dBm
 20 TD220 Installation/Operation Guide 05-4819A01, Rev. 01  Table 12. Radio Configuration Menu Items Parameter R/W Description A) Base Transmit FrequencyR/W The frequency in the 217.44625 to 221.95625 MHz range that the Base Units use for over the air transmissions.B) Mobile Transmit FrequencyR/W The frequency in the 217.44625 to 221.95625 MHz range that the Mobile Units use for over the air transmissions.
 05-4819A01, Rev. 01 TD220 Installation/Operation Guide 21 C) Base Transmit Slots R/W The number of slots within each 8-slot second that are reserved for base transmissions if needed. NOTE: This parameter must match on all bases and mobiles in the network.D) Output Power R/W The RF Output Power from 2 to 25 Watts with which the radio transmits.E) Force TX Key R/W “Normal” to allow the radio to operate in data mode, “Forced” to key the transmitter for test purposes.F) TX Key Timeout R/W If TX Key is Forced, the radio will automatically De-Key after this timeout. Table 12. Radio Configuration Menu Items Parameter R/W Description
 22 TD220 Installation/Operation Guide 05-4819A01, Rev. 01  Table 13. Security Configuration Menu Items Parameter R/W Description A) Telnet Access R/W If “enabled”, the radio allows users to Telnet to the radio via Ethernet. If “disabled”, users must manage the radio via SNMP or the serial console.B) User Passwords Allows modification of the admin password.
 05-4819A01, Rev. 01 TD220 Installation/Operation Guide 23 Table 14. xxxxxParameter R/W DescriptionA) ITCS Logging Access the ITCS Logging configuration menu.B) Wireless Packet StatisticsAccess the Wireless Packet Statistics menu where you can view the number of messages passed over the air.C) Ethernet Packet StatisticsAccess the Ethernet Packet Statistics menu where you can view the number of messages passed via Ethernet.D) Event Log Access the Event Log menu where you can view the radio's log of system events and alarms.
24 TD220 Installation/Operation Guide 05-4819A01, Rev. 01 Table 15. xxxxxParameter R/W DescriptionA) ITCS Logging R/W If “enabled”, send UDP messages to a logging host.B) ITCS Log Server R/W The IP address to send UDP messages for logging ITCS traffic.C) ITCS Log Server Port R/W The IP port number to send UDP messages for logging ITCS traffic.
05-4819A01, Rev. 01 TD220 Installation/Operation Guide 25Table 16. xxxxxParameter R/W DescriptionPackets Received R The number of packets received over the air.Packet Sent R The number of packets transmitted over the air.Bytes Received R The number of Bytes for all packets received over the air.Bytes Sent R The number of Bytes for all packets transmitted over the air.Receive Errors R The number of messages received over the air that did not decode properly.A) Clear Statistics R/W Reset all results to zero.
26 TD220 Installation/Operation Guide 05-4819A01, Rev. 01 Table 17. xxxxxParameter R/W DescriptionPackets Received R The number of packets received over Ethernet.Packet Sent R The number of packets transmitted over Ethernet.Bytes Received R The number of Bytes for all packets received over Ethernet.Bytes Sent R The number of Bytes for all packets transmitted over the air.Receive Errors R The number of messages received over the air that did not decode properly.A) Clear Statistics R/W Reset all results to zero.
05-4819A01, Rev. 01 TD220 Installation/Operation Guide 27Table 18. xxxxx  Parameter R/W DescriptionA) Current Alarms Display a list of the alarms currently active within the radio.B) View Event Log Scroll through the historical list of radio events and alarms.C) Clear Event Log Erase all history of radio events and alarms.D) Send Event Log Begin a TFTP transfer of the historical list of all radio events to the IP Address given by “Event Log Host Address”.E) Event Log Host AddressR/W The IP Address of the server that will accept TFTP transfer of the Event Log.F) Event Log Filename R/W The file name on the server for the event log.G) TFTP Timeout R/W If the radio cannot reach the TFTP server, it waits this long before giving up at each step in the process.H) Syslog Server Address R/W As events and alarms occur in real time, send them via the standard SYSLOG protocol (RFC 3164) to the server at this IP Address.
28 TD220 Installation/Operation Guide 05-4819A01, Rev. 01 This screen displays the event number, date and time, and event or alarm for each occurrence.
05-4819A01, Rev. 01 TD220 Installation/Operation Guide 29Table 19. xxxxx  Parameter R/W DescriptionModel R The Model Type of the radio.Serial Number R The factory-assigned unique radio Serial Number.Uptime R The number of elapsed hours, minutes, and seconds since the radio last rebooted.Date R The Date from the GPS receiver.Time R The Time from the GPS receiver.A) Date Format R/W Change how the date and time are displayed.B) Console Baud Rate R/W The serial port rate the console will communicate at.C) Device Names Access the Device Names menu where you can modify the user-programmable name strings for this radio.
30 TD220 Installation/Operation Guide 05-4819A01, Rev. 01 Table 20. xxxxx  Parameter R/W DescriptionA) Device Name R/W Free-form field where you can enter a nickname for this radio.B) Contact R/W Free-form field where you can indicate who to contact in case the radio needs service.C) Location R/W Free-form field where you can describe the site at which the radio is installed.D) Description R/W Free-form field where you can enter details describing this radio.
05-4819A01, Rev. 01 TD220 Installation/Operation Guide 31Table 21. xxxxx  Parameter R/W DescriptionA) Reprogramming Access the Reprogramming menu where you can upgrade the radio's firmware.B) Configuration Scripts Access the Configuration Scripts menu where you can save and restore the radio's configuration to and from a text file via a TFTP server.C) Ping Utility Access the Ping Utility menu where you can confirm Ethernet communications with one or more hosts.
32 TD220 Installation/Operation Guide 05-4819A01, Rev. 01 Table 22. xxxxx  Parameter R/W DescriptionA) TFTP Host Address R/W The IP address of the TFTP server from which you will download a new firmware image.B) Firmware Filename R/W The file name for the firmware image. This file must exist on the server.C) TFTP Timeout R/W If the radio cannot reach the TFTP server, it waits this long before giving up at each step in the process.D) Retrieve File Command the radio to request the firmware image from the TFTP server.E) Image Verify Command the radio to perform a check of the firmware image in memory.F) Image Copy Command the radio to copy the active firmware image to the inactive position.G) Reboot Device Command the radio to restart using one of the firmware imagesCurrent Firmware Shows the version number of both firmware images, plus which one is currently executing.
05-4819A01, Rev. 01 TD220 Installation/Operation Guide 33Table 23. xxxxx  Parameter R/W DescriptionA) TFTP Host Address R/W The IP address of the TFTP server to or from which you will upload or download a configuration script.B) Config Filename R/W The filename to or from which you will save or restore the radio's configuration.C) TFTP Timeout R/W If the radio cannot reach the TFTP server, it waits this long before giving up at each step in the pro-cess.D) Retrieve File Command the radio to get the file from the TFTP server.E) Send File Command the radio to send the file to the TFTP server.
34 TD220 Installation/Operation Guide 05-4819A01, Rev. 01 Configuration scripts are used to store and duplicate radio settings. To use this facility, send the configuration file from a radio to the TFTP server. It can then be archived or edited and retrieved from the same or different radios. For more information, contact GE MDS.Table 24. xxxxx  Parameter R/W DescriptionA) Address to Ping R/W The IP address of the network host to which you will send test mes-sages.B) Count R/W The number of test messages you will send.C) Packet Size R/W The number of Bytes each test message will contain.D) Ping Command the radio to begin the ping test.
05-4819A01, Rev. 01 TD220 Installation/Operation Guide 35TroubleshootingHere are some tips to help resolve issues when operating the TD220.SymptomPossible CauseRadio shows messages are received via Ethernet, but it will not transmit over the air.Radio is alarmed.XXXXXXXXXXOriginal Follows...Under RevisionXXXXXXXXXFront Panel ConnectorsFigure 4 and Figure 5 show the interface connectors and indicators on the transceiver’s front an d rear panels. These items are referenced in the installation steps given later in this guide.Invisible place holderFigure 4. Antenna & DC Power Connectors Antenna(Mini-UHF)Power Input(10.5 to 16 Vdc @ 8A)
36 TD220 Installation/Operation Guide 05-4819A01, Rev. 01 Invisible place holderFigure 5. Data Interface Connector & LED Status PanelINSTALLATIONThere are three main requirements for installing the transceiver: • Adequate and stable primary power• An efficient and properly installed antenna system• Correct data connections between the transceiver and the data device.Figure 6 shows a typical station arrangement. This is followed by step-by-step procedures for installing the transceiver and making front and rear panel connections.LED Indicator Panel(See inset above)Data Interface(DB-25)PWRDCDTXDRXD
05-4819A01, Rev. 01 TD220 Installation/Operation Guide 37Figure 6. Typical Station ArrangementInstallation StepsBelow are the basic steps for installing the transceiver. Refer to Figure 6 as necessary to make the cable connections.1. Mount the transceiver to a stable surface using the brackets supplied with the radio. Begin by attaching the radio’s mounting brackets to the bottom of the transceiver case (if not already attached) using the four 6-32 x 1/4 inch (6 mm) screws supplied. Figure 7 shows the mounting bracket dimensions.NOTE: To prevent moisture from entering the radio, do not mount the case with the cable connectors pointing up. Also, dress all cables to prevent moisture from running along the cables and into the radio.DC POWER CABLE10.5—16 VDC @ 8ANegative GroundDATA EQUIPMENTANTENNASYSTEMLOW-LOSSCOAXIAL CABLE(50 Ohm)RADIOTRANSCEIVER
38 TD220 Installation/Operation Guide 05-4819A01, Rev. 01 Invisible place holderFigure 7. Transceiver Mounting Bracket DimensionsUsing screws longer than 1/4 inch (6 mm) to attach the brackets to the radio may damage the internal PC board. Use only the supplied screws.2. Install the antenna and feedline for the station. The antenna used with the transceiver must be designed to operate in the radio’s frequency band, and be mounted in a location that pro-vides a clear, path to the other associated station(s). Use low loss coaxial feedline and keep the cable as short as possible.8.5"216 mm1.75"4.44 CM6.63"168 mm2.75"70 mm7.25"184 mmALTERNATEPOSITION5.625"143 mm2.25"57 mm2.0"50 mmCAUTIONPOSSIBLEEQUIPMENTDAMAGE
05-4819A01, Rev. 01 TD220 Installation/Operation Guide 393. Connect the data equipment to the DATA INTERFACE connec-tor. Check SPECIFICATIONS on Page 47 for pin wiring details.Note: The radio’s DIAGNOSTICS port is used for reprogramming the radio’s firmware.4. Connect primary power to the transceiver. Power applied must be within 10.5–16 Vdc and capable of continuously providing at least 8 Amperes. A power connector with is provided with each unit (see Figure 6).The transceiver is designed for use with nega-tive-ground systems only. The power supply should be equipped with overload protection (NEC Class 2 rating), to protect against a short circuit between its output ter-minals and the radio’s power connector.5. Set the radio’s configuration. The transceiver is designed for quick installation with a minimum of software configuration required. a. Connect a PC to the transceiver’s DATA INTERFACE connec-tor as shown in Figure 8. If desired, a cable may be built using the information shown on Page 47 of this guide.b. Launch a terminal communications program, such as Hyper-Terminal (included with most WindowsTM systems). Press the  key a few times (at half-second intervals) to receive the ready “>” prompt on the screen. NOTE: To prevent unintended keying of the transmitter duringmanagement activities, set PTTSIG to OFF, or do notconnect to Pin 6 of the COM1 port.CAUTIONPOSSIBLEEQUIPMENTDAMAGEENTER
40 TD220 Installation/Operation Guide 05-4819A01, Rev. 01 Invisible place holderFigure 8. PC Configuration Setupc. Set the transmit frequency by entering TX xxx.xxxx, where xxx.xxxx is the frequency in MHz. Press  . The response PROGRAMMED OK indicates successful entry.d. Set the receive frequency by entering RX xxx.xxxx, where xxx.xxxx is the frequency in MHz. Press  . The response PROGRAMMED OK indicates successful entry.e. Set the radio’s modem type if necessary, using the MODEM xxxx command, where xxxx is the modem selection (typically 4800 or 9600). The default setting is 9600. Set the radio’s serial data interface rate (typically BAUD 9600 8N1).This completes the initial setup and configuration of the radio.PC Running Terminal SessionTransceiverTo DB-25Data Interface PortENTERENTER
05-4819A01, Rev. 01 TD220 Installation/Operation Guide 41SOFTWARE COMMAND SUMMARYTable 25 lists software commands commonly used during initial installation and setup of the transceiver. Detailed Command Usage(This section currently under revision)chan [chan # [rxfreq # [txfreq # [pwr # [bw # ] ] ] ] }Table 25. Command Summary  Command Name  FunctionBAUD [xxxx xxx] Sets radio’s serial data interface rate/format. Default setting is BAUD 9600 8N1.DKEY Dekey the radio (transmitter OFF). This is generally a radio test command.KEY Key the radio (transmitter ON). This is generally a radio test command.MODEM [xxxx] Set the modem characteristics of the radio.PWR [37–45] Set or display the transmit power setting.PTTSIG [ON, OFF] Set/display push-to-talk configuration.RSSI Display the Received Signal Strength Indication.RX [xxx.xxxx] Set or display receiver frequency.SER Display the radio serial number.SNR Signal-to-Noise Ratio (in dB).SPECTRUM [xxx.xx]Display internal spectrum analyzer, where xxx.xx characters denote center frequency in MHz. The command spectrum may be entered alone to view current operating channel.SREV Display the Software Revision Level.STAT Display radio status and alarms.TEMP Display the internal temperature of the radio in degrees C.TX [xxx.xxxx] Set or display the transmit frequency.
42 TD220 Installation/Operation Guide 05-4819A01, Rev. 01     chan - channel # {all,0-8]    rxfreq - receiver frequency    txfreq - transmitter frequency    pwr - power in watts (2, 5, 20, 25, 30)    bw - bandwidth (12.5, 25)Examples:>chanChannel 1 RX 452.92500 MHz  TX 452.92500 MHz  PWR 30 Watts  BW 25.000 KHz>chan allSelected LCT Channel is 0Channel 0 RX 450.00000 MHz  TX 453.00000 MHz  PWR 5 Watts  BW 25.000 KHzChannel 1 RX 452.92500 MHz  TX 452.92500 MHz  PWR 30 Watts  BW 25.000 KHzChannel 2 RX 452.95000 MHz  TX 452.95000 MHz  PWR 30 Watts  BW 25.000 KHzChannel 3 RX 457.92500 MHz  TX 457.92500 MHz  PWR 30 Watts  BW 25.000 KHzChannel 4 RX 457.95000 MHz  TX 457.95000 MHz  PWR 30 Watts  BW 25.000 KHzChannel 5 RX 452.92500 MHz  TX 452.92500 MHz  PWR 30 Watts  BW 25.000 KHzChannel 6 RX 452.95000 MHz  TX 452.95000 MHz  PWR 30 Watts  BW 25.000 KHzChannel 7 RX 457.92500 MHz  TX 457.92500 MHz  PWR 30 Watts  BW 25.000 KHzChannel 8 RX 457.95000 MHz  TX 457.95000 MHz  PWR 30 Watts  BW 25.000 KHz>chan 8 rxfreq 453rxfreq 453Channel 8 RX 453.00000 MHz  TX 457.95000 MHz  PWR 30 Watts  BW 25.000 KHz>chan 8 pwr 20pwr 20Channel 8 RX 453.00000 MHz  TX 457.95000 MHz  PWR 20 Watts  BW 25.000 KHz>chan 8 bw 12.5bw 12.5
05-4819A01, Rev. 01 TD220 Installation/Operation Guide 43Channel 8 RX 453.00000 MHz  TX 457.95000 MHz  PWR 20 Watts  BW 12.500 KHz>mode test>selchan helpUsage:  selchan [0-8] >selchan 8Channel Number 8>chanChannel 8 RX 453.00000 MHz  TX 457.95000 MHz  PWR 20 Watts  BW 12.500 KHz>keyTRANSMITTER ENABLED>dkeyTRANSMITTER DISABLED>mode normalTROUBLESHOOTINGFor proper operation, all radios in the network must meet these basic requirements:• Adequate and stable primary power• Secure connections (RF, data and power)• A clear transmission path between stations• An efficient antenna system providing adequate received signal strength.• Proper programming of the transceiver’s operating parameters• The correct interface between the transceiver and the connected data equipment (correct cable wiring, proper data format, tim-ing, etc.)LED IndicatorsThe LED status indicators (Figure 9) are an important troubleshooting aid and should be checked whenever a problem is suspected. Table 26 describes the function of each status LED on the front panel of the radio.
44 TD220 Installation/Operation Guide 05-4819A01, Rev. 01 Invisible place holderFigure 9. LED IndicatorsEvent CodesWhen an alarm condition exists, the transceiver creates a code that can be read on a connected terminal. These codes can be helpful in resolving many system difficulties. Refer to Table 27 (Page 45) for a definition of the event codes.Checking for Alarms—STAT commandTo check for alarms, connect a terminal to the radio’s DIAGNOSTICS port. See SPECIFICATIONS on Page 47 for pinout information. Enter STAT on the connected terminal. If no alarms exist, the message NO ALARMS PRESENT appears on the display.If an alarm does exist, a two-digit alarm code (00–31) is displayed and the event is identified as a Major or Minor Alarm. A brief description of the alarm is also given.If more than one alarm exists, the word MORE appears on the screen. To view additional alarms, press  .Table 26. LED Status Indicators LED Name DescriptionPWR • Continuous—Power applied, no problems detected.• Rapid flash (5 times-per-second)—Alarm indication.TXD Data being transmitted over the air.RXD Data being received over the air.DCD When lit, indicates that a communication link is established with the other station(s).PWRDCDTXDRXDENTER
05-4819A01, Rev. 01 TD220 Installation/Operation Guide 45Major Alarms vs. Minor AlarmsMajor Alarms—report serious conditions that generally indicate a hardware failure, or other abnormal condition that will prevent (or seriously hamper) further operation of the transceiver. Major alarms generally indicate the need for factory repair. Contact your factory representative for assistance.Minor Alarms—report conditions that, under most circumstances will not prevent transceiver operation. This includes out-of-tolerance con-ditions, baud rate mismatches, etc. The cause of these alarms should be investigated and corrected to prevent system failure.Event Code DefinitionsTable 27 contains a listing of event codes that may be reported by the transceiver. The codes shown are a subset of a larger pool of codes used for various GE MDS products. For this reason, the table does not show a sequential listing of all code numbers. Only the codes appli-cable to this product are shown. Table 27. Event Codes  Event CodeEvent Class Description01 Major Improper software detected for this radio model.04 Major The RF synthesizer is reporting an out-of-lock condition.08 Major The system is reporting that it has not been calibrated. Factory calibration is required for proper radio operation.12 Major Receiver time-out. No data received within the specified receiver time-out time.13 Minor A Transmitter timeout was detected. The radio stayed keyed longer than the duration specified by the TOT command.17 Minor A data parity fault has been detected on the PAYLOAD port. This usually indicates a parity setting mismatch between the radio and the customer equipment.18 Minor A data framing error has been detected on the PAYLOAD port. This may indicate a baud rate mismatch between the radio and the customer equipment.
46 TD220 Installation/Operation Guide 05-4819A01, Rev. 01 Internal Spectrum AnalyzerThe radio contains a built-in spectrum analyzer tool (Figure 10) that can be displayed on a connected PC. The tool is helpful in diagnosing interference problems on or near your channel frequency.Access the spectrum analyzer by entering spectrum at the command prompt. A display appears showing detected signals on your current channel.Optionally, you can specify a frequency at the command prompt to view the surrounding spectrum of that frequency. To do this, enter spectrum xxx.xx, where xxx.xx is the frequency in MHz.As shown in Figure 10, the display creates a received signal strength indication (RSSI) vs. frequency plot for the frequency and sur-rounding signals. By analyzing the display, you can determine the presence of other signals near the transceiver’s operating frequency. This information can be helpful in troubleshooting interference prob-lems.26 Minor The DC input voltage is out-of-tolerance. If the voltage is too far out of tolerance, operation may fail.31 Minor The transceiver’s internal temperature is approaching an out-of-tolerance condition. If the temperature drifts outside of the recommended operating range, system operation may fail.Table 27. Event Codes (Cont’d)Event CodeEvent Class Description
05-4819A01, Rev. 01 TD220 Installation/Operation Guide 47Invisible place holderFigure 10. Internal Spectrum Analyzer DisplaySPECIFICATIONSGENERALFrequency Ranges*: 217-220 MHz220-222 MHzRECEIVERMaximum Usable Sensitivity: –110 dBm at 1x10–6 BER (Preliminary)Bandwidth: 12.5 kHzTRANSMITTERRF Carrier Power: 2 Watts (217-220 MHz) 25 Watts (220-222 MHz)Duty Cycle: 25%Output Impedance: 50 ΩChannel Spacing: 6.25, 12.5 kHzFCC Emission Designators:                 12.5 kHz B/W: 11K0F1D
48 TD220 Installation/Operation Guide 05-4819A01, Rev. 01 :DATA CHARACTERISTICSPayload Signaling Type: EIA/RS-485Connector Type: DB-25 FemalePayload Data Rates: 300–115200 bps, asynchronousPayload Data Latency: 10 ms maximumDIAGNOSTICS INTERFACESignaling Standard: RS-232PRIMARY POWERVoltage: 13.8 Vdc Nominal (10.5 to 16 Vdc)Negative-Ground Systems OnlyTX Supply Current: 8 Amperes (Typical) @ 30 Watts OutputRX Supply Current: Operational—125 mA, NominalFuse: 8-Ampere, internalENVIRONMENTALHumidity: 95% at 40 degrees C (104°F), non-condensingTemperature Range: –40 to 70 degrees C (–40°F to +158°F)Weight: 1.0 kilograms
Installation Guide
GE MDS, LLCRochester, NY 14620General Business: +1 585 242-9600FAX: +1 585 242-9620Web: www.GEmds.com175 Science Parkway

Navigation menu