GE MDS DS-NH900 MDS iNet 900 User Manual 2806H iNET Series

GE MDS LLC MDS iNet 900 2806H iNET Series

user manual

 Reference Manual MDS 05-2806A01, Rev. HNOVEMBER 2007Wireless IP/Ethernet TransceiveriNET-II 900 Firmware Release 2.3iNET 900 Firmware Release 6.3MDS iNET SeriesMDS iNET-II 900TMMDS iNET 900TMGE MDS
POWER SUPPLY13.8 VDC @ 580 mA (Max.)(10.530 Vdc) Negative Ground OnlyDATA TERMINALEQUIPMENT ORLAN/WANCOMPUTERW/ TERMINALEMULATORTRANSCEIVERLOW-LOSS FEEDLINEQUICK-STQUICK-STARARTT INSTRUCTIONS INSTRUCTIONSANTENNASYSTEMINSTALLATION SUMMARYStep 1  Mount the TransceiverStep 2  Install the AntennaStep 3  Measure & Connect Primary Power (10.530 Vdc)Step 4  Review the Tranceivers ConfigurationDevice ModeAccess Point, or Remote (Default)Network NameUnique name for each radio network.Required for Remotes to associate with Access Point.IP AddressMust be a unique number to allow for IP accessthrough the Ethernet Port.NOTE: A unique IP address is essential to access the browser-basedManagement System.RF Output PowerAdjust as necessary for regulatory compliance.(Default = 1 Watt /+30 dBm)PasswordUsed for remote access and some Management Systemfeatures. (Default = admin)Step 5  Connect the Data EquipmentConnect the data equipment to data port(s): LAN10BaseT Ethernet-compatible equipment: Ethernet Hub (Straight-Through Cable); Ethernet Node (Crossover) TYPICAL INSTALLATIONThe Management System can be accessed through the COM1 Port using a terminal emulator. The basic  items listed below, andmany other parameters and tools can be accessed through this tool. HTTP, Telnet access, and changing some parameters arecontrolled by password.BASIC CONFIGURATION DEFAULTS COM2Serial, RS/EIA-232 compatible equipment COM1Management System (Default); Serial (Alternate)Step 6  Check for Normal Operation Observe the transceiver LED status panel for the proper indications. In a normally operating system, the following LED indicationswill be seen within 30 seconds of power-up:PWRLights continuously LANOn or blinks intermittently  LINK On or blinks intermittently (Remotes: if associated) Use PING command to test basic data link integrity between Access Point and Remotes. If the PING command is successful, connect the RTU/data equipment to the data port and verify normal operation. If the LINK LED on Remotes is not on after 20 to 30 seconds, the unit has failed to associate with the Access Point. It may benecessary to reposition or redirect the radios antenna for better reception/signal strength. Check connected data equipment for normal operationITEM MGT SYSTEM MENUDevice Mode Network ConfigurationUnit Password Device InformationNetwork Name Network ConfigurationIP Address Network ConfigurationRF Output Power Radio ConfigurationVALUES/RANGE Remote Access Point 18 alphanumeric characters Case-sensitive; can be mixed case 116 alphanumeric characters Case-sensitive; can be mixed caseContact your Network Administrator2030 dBm @ 50W (0.11.0 Watt)DEFAULTRemoteadmin(lower case)"Not Programmed"192.168.1.1+30 dBm (1.0 Watt)Detailed instructions for setting transceiver parameters are contained in Section 3 of this manual.
 05-2806A01, Rev. H iNET Series Reference Manual i TABLE OF CONTENTS 1 PRODUCT OVERVIEW AND APPLICATIONS ........... 1 1.1   ABOUT THIS MANUAL.........................................................................................................3 1.1.1   Related Publication  ....................................................................................................................3 1.2   PRODUCT DESCRIPTION................................................................................................... 3 1.2.1   Model Offerings  ..........................................................................................................................51.2.2   Differences Between iNET and iNET-II Models ..........................................................................61.2.3   GE MDS P21 Protected Network (Redundant) Configuration ....................................................6 1.3   APPLICATIONS .................................................................................................................... 7 1.3.1   Wireless LAN ..............................................................................................................................71.3.2   Point-to-Point LAN Extension .....................................................................................................81.3.3   Backhaul for Serial Radio Networks ...........................................................................................81.3.4   Multiple Protocols and/or Services  .............................................................................................91.3.5   Wireless LAN with Mixed Services ...........................................................................................101.3.6   Upgrading Older Wireless Network with Serial Interfaces  ..................................................................................................................................10Replacing Legacy Wireless Products ............................................................................................ 11Supplement legacy wireless network with IP services................................................................... 111.3.7   High-Speed Mobile Data  .......................................................................................................... 11 1.4   NETWORK DESIGN CONSIDERATIONS.......................................................................... 12 1.4.1   Extending Network Coverage with Repeaters ..........................................................................12What is a Repeater System? .........................................................................................................12Option 1Using two transceivers to form a repeater station(back-to-back repeater)..................................................................................................................12Option 2Using the AP as a Store-and-Forward Packet Repeater ........................................................................................................................................131.4.2   Protected Network Operation using Multiple Access Points .....................................................141.4.3   Collocating Multiple Radio Networks ........................................................................................14The Network Name and the association process ..........................................................................14Can radio frequency interference (RFI) disrupt my wireless network? ..........................................15 1.5   CYBER SECURITY ............................................................................................................15 1.6   ACCESSORIES .................................................................................................................. 17
 ii iNET Series Reference Manual 05-2806A01, Rev. H 2 EMBEDDED MANAGEMENT SYSTEM.................... 19 2.1   INTRODUCTION ................................................................................................................ 23 2.1.1   Differences in the User Interfaces  ............................................................................................23 2.2   ACCESSING THE MENU SYSTEM ................................................................................... 25 2.2.1   Methods of Control  ...................................................................................................................262.2.2   PC Connection & Log In Procedures  .......................................................................................262.2.3   Navigating the Menus ...............................................................................................................31Via Terminal Telnet or SSH SessionsRecommended for first-time log-in.................................................................................................31Navigating via Web Browser..........................................................................................................31 2.3   BASIC DEVICE INFORMATION......................................................................................... 32 2.3.1   Starting Information Screen ......................................................................................................322.3.2   Main Menu ................................................................................................................................342.3.3   Configuring Basic Device Parameters ......................................................................................35Device Information .........................................................................................................................35Device Names Menu......................................................................................................................36 2.4   CONFIGURING NETWORK PARAMETERS ..................................................................... 37 2.4.1   Network Configuration Menu ....................................................................................................372.4.2   Network Interface Configuration Menu .....................................................................................39Virtual LAN in iNET-II and iNET .....................................................................................................40Configuring for Operation with VLAN.............................................................................................41Configuring the IP Address when VLAN Status is Enabled ...........................................................42Configuring the IP Address When VLAN Status is Disabled..........................................................432.4.3   Ethernet Port Configuration Menu ............................................................................................452.4.4   DHCP Server Configuration  .....................................................................................................462.4.5   SNMP Agent Configuration .......................................................................................................472.4.6   Prioritized AP Configuration Submenu  .....................................................................................49 2.5   RADIO CONFIGURATION.................................................................................................. 51 2.5.1   Radio Configuration Menu ........................................................................................................512.5.2   Channel Config Menu ...............................................................................................................542.5.3   Skip Zones Menu  .....................................................................................................................552.5.4   Auto Data Rate Configuration Menu .........................................................................................562.5.5   Mobility Configuration Menu .....................................................................................................58Additional Considerations for Mobile Operation.............................................................................59At Every Mobile (Remote) Radio ...................................................................................................59At Every AP Radio .........................................................................................................................60 2.6   CONFIGURING THE SERIAL PORTS ............................................................................... 60 2.6.1   Overview  ..................................................................................................................................60Com1 Port—Dual Purpose Capability .............................................................................................61
 05-2806A01, Rev. H iNET Series Reference Manual iii TCP vs. UDP..................................................................................................................................61Serial Encapsulation ......................................................................................................................61TCP Client vs. TCP Server ............................................................................................................62UDP Multicast ................................................................................................................................62PPP................................................................................................................................................63Data Buffering ................................................................................................................................63Implementing Configuration Changes............................................................................................63Serial Configuration Wizard ...........................................................................................................632.6.2   Serial Data Port Configuration Menu ........................................................................................632.6.3   Configuring for UDP Mode  .......................................................................................................642.6.4   Configuring for TCP Mode ........................................................................................................682.6.5   Configuring for PPP Mode ........................................................................................................702.6.6   IP-to-Serial Application Example  ..............................................................................................712.6.7   Point-to-Multipoint IP-to-Serial Application Example  ................................................................ 722.6.8   Point-to-Point Serial-to-Serial Application Example  .................................................................742.6.9   Combined Serial and IP Application Example  ..........................................................................75Operation and Data Flow ...............................................................................................................752.6.10   Virtual LAN in iNET-II and iNET ..............................................................................................77Configuring for Operation with VLAN.............................................................................................78 2.7   CYBER SECURITY CONFIGURATION ............................................................................. 78 2.7.1   Device Security  ........................................................................................................................792.7.2   Wireless Security ......................................................................................................................80Local AuthenticationApproved Remotes/Access Points List Submenu......................................812.7.3   RADIUS Configuration  .............................................................................................................82Operation of Device Authentication................................................................................................83Operation of User Authentication ...................................................................................................832.7.4   RADIUS Configuration  .............................................................................................................842.7.5   Certificate Management (Remote transceivers only)  ...............................................................84 2.8   PERFORMANCE VERIFICATION ...................................................................................... 85 2.8.1   RSSI by Zone Menu (Remotes Only) .......................................................................................872.8.2   Event Log Menu  .......................................................................................................................88Time and Date................................................................................................................................88View Current Alarms ......................................................................................................................90View Event Log ..............................................................................................................................912.8.3   Packet Menu  ............................................................................................................................91Wireless Packet Statistics..............................................................................................................91Ethernet Packet Statistics ..............................................................................................................92Packets Received by Zone ............................................................................................................932.8.4   Wireless Network Status (Remotes Only)  ................................................................................94The Transceivers Association Process .........................................................................................94The Wireless Network Status Screen (Remotes Only) .................................................................. 952.8.5   Remote Listing Menu (Access Points Only)   ............................................................................962.8.6   Endpoint Listing Menu (Access Points Only)  ...........................................................................972.8.7   Remote Performance Listing Menu (Access Points Only)   ..........................................................................................................................98
 iv iNET Series Reference Manual 05-2806A01, Rev. H 2.8.8   Serial Data Statistics Menu  ......................................................................................................99 2.9   MAINTENANCE.................................................................................................................. 99 2.9.1   Reprogramming Menu ............................................................................................................100Upgrading the Firmware ..............................................................................................................102Error Messages During File Transfers .........................................................................................1042.9.2   Configuration Scripts Menu  ....................................................................................................105How Configuration Files Work .....................................................................................................105Sample of Configuration Script File .............................................................................................106Editing Configuration Files ...........................................................................................................1072.9.3   Authorization Keys Menu ........................................................................................................1082.9.4   Change the Type of Remote ...................................................................................................1082.9.5   Auto-Upgrade/Remote-Reboot Menu  .....................................................................................108Firmware Upgrade (with AP Acting as a TFTP Server)................................................................1092.9.6   Radio Test Menu ..................................................................................................................... 1102.9.7   Ping Utility Menu  .................................................................................................................... 1112.9.8   Reset to Factory Defaults ....................................................................................................... 111Password Reset........................................................................................................................... 111 3  TROUBLESHOOTING.............................................113 3.1   Interpreting the Front Panel LEDs .................................................................................... 115 3.2   Troubleshooting Using the Embedded Management System........................................... 116 3.2.1   Starting Information Screen .................................................................................................... 1173.2.2   Packet Statistics Menu  ........................................................................................................... 1183.2.3   Serial Port Statistics Menu  ..................................................................................................... 1193.2.4   Diagnostic Tools  ..................................................................................................................... 119 3.3   Using Logged Operation Events....................................................................................... 119 3.4   Alarm Conditions............................................................................................................... 120 3.5   Correcting Alarm Conditions ............................................................................................. 121 3.6   Logged Events .................................................................................................................. 123
 05-2806A01, Rev. H iNET Series Reference Manual v 4 PLANNING A RADIO NETWORK ........................... 127 4.1   INSTALLATION PLANNING ............................................................................................. 129 4.1.1   General Requirements  ...........................................................................................................129DIN Rail Mounting Option ............................................................................................................1314.1.2   Site Selection  .........................................................................................................................1314.1.3   Terrain and Signal Strength ....................................................................................................1324.1.4   Antenna & Feedline Selection  ................................................................................................1324.1.5   How Much Output Power Can be Used?  ...............................................................................1354.1.6   Conducting a Site Survey .......................................................................................................1364.1.7   A Word About Radio Interference  ...........................................................................................1364.1.8   Notes on Using 28 VDC Power Supplies  ...............................................................................138 4.2   RADIO (RF) MEASUREMENTS ....................................................................................... 139 4.2.1   Antenna System SWR and Transmitter Power Output ...........................................................140Introduction ..................................................................................................................................140Procedure ....................................................................................................................................1404.2.2   Antenna Aiming  ......................................................................................................................141Introduction ..................................................................................................................................141Procedure ....................................................................................................................................141 4.3   dBm-WATTS-VOLTS CONVERSION CHART.................................................................. 143 4.4   PERFORMANCE NOTES................................................................................................. 144 4.4.1   Wireless Bridge  ......................................................................................................................1444.4.2   Distance-Throughput Relationship  .........................................................................................1444.4.3   Data LatencyTCP versus UDP Mode  ................................................................................. 1454.4.4   Data Compression ..................................................................................................................1454.4.5   Packets-per-Second (PPS)  ....................................................................................................1454.4.6   Station-to-Station Traffic  .........................................................................................................1454.4.7   Interference has a Direct Correlation to Throughput  ..............................................................1454.4.8   Maximizing Throughput  ..........................................................................................................1464.4.9   Placing an iNET Radio Behind a Firewall ...............................................................................147 4.5   SNMPv3 NOTES .............................................................................................................. 147 4.5.1   Overview  ................................................................................................................................147SNMPv3 Accounts .......................................................................................................................148Context Names ............................................................................................................................148Password-Mode Management Changes......................................................................................149 5 TECHNICAL REFERENCE...................................... 153 5.1   DATA INTERFACE CONNECTORS ................................................................................. 155 5.1.1   LAN Port .................................................................................................................................1555.1.2   COM1 Port  .............................................................................................................................156
 vi iNET Series Reference Manual 05-2806A01, Rev. H 5.1.3   COM2 Port  .............................................................................................................................156 5.2   FUSE REPLACEMENT PROCEDURE ............................................................................ 157 5.3   TECHNICAL SPECIFICATIONS ....................................................................................... 158 5.4   CHANNEL HOP TABLE .................................................................................................... 161 6 GLOSSARY OF TERMS AND ABBREVIATIONS... 165 Copyright Notice This publication is protected by U.S.A. copyright law. Copyright 2007, GE MDS. All rights reserved. ISO 9001 Registration GE MDS adheres to this internationally-accepted ISO 9001 quality system standard. To our Customers We appreciate your patronage. You are our business. We promise to serve and anticipate your needs. We will strive to give you solutions that are cost effective, innovative, reliable and of the highest quality possible. We promise to build a relationship that is forthright and ethical, one that builds confidence and trust. Products Covered in this Manual This manual covers two members of the GE MDS iNET Transceiver Series, both of which are designed to be operated under the FCCs Part 15 license-free rules. The iNET radio is a Frequency Hopping Spread Spectrum (FHSS) transceiver that operates at data speeds of 256 and 512 kbps.The iNET-II is a similar design, but it is certified under the Digital Transmission System (DTS) provisions of FCC Part 15 and can operate at data speeds of 512 or 1024 kbps. Operational differ-ences between these two models are identified, as necessary, in this manual. NOTE: GE MDS iNET and GE MDS iNET-II transceivers are  not  over-the-air compatible. Other GE MDS  i NET 900 Series Documentation Startup Guide The associated GE MDS  i NET 900 Series Startup Guide, P/N 05-2873A01, is pro-vided with the transceiver and is limited to essential information needed for installers. The instal-lation guide assumes some guidance to installers will be provided by the readers of this manual. This includes such things as antenna selection, radio communication site survey tools and tech-niques, and network design. Related Materials on the Internet Data sheets, frequently asked questions, case studies, applica-tion notes, firmware upgrades and other updated information is available on the GE MDS Web site at www.GEmds.com.
 05-2806A01, Rev. H iNET Series Reference Manual vii About GE MDS Almost two decades ago, GE MDS began building radios for business-critical applications. Since then, weve installed nearly 100,000,000 radios in over 110 countries. To succeed, we overcame impassable terrain, brutal operating conditions and disparate, complex network configurations. We also became experts in wireless communication standards and system applications worldwide. The result of our efforts is that today, thousands of utilities around the world rely on GE MDS-based wireless networks to manage their most critical assets.The majority of GE MDS radios deployed since 1985 are still installed and performing within our customers’ wireless networks. Thats because we design and manufacture our products in-house, according to ISO 9001 which allows us to control and meet stringent global quality standards. Thanks to our durable products and comprehensive solutions, GE MDS is the wireless leader in industrial automationincluding oil and gas production and transportation, water/wastewater treatment, supply and transportation, electric transmission and distribution and many other utility applications. GE MDS is also at the forefront of wireless communications for private and public infrastructure and online transaction processing. Now is an exciting time for GE MDS and our cus-tomers as we look forward to further demonstrating our abilities in new and emerging markets.As your wireless needs change you can continue to expect more from GE MDS. We’ll always put the performance of your network above all. Visit us at www.GEmds.com for more information. OPERATIONAL & SAFETY NOTICESUL/CSA Notice This product is available for use in Class 1, Division 2, Groups A, B, C & D Hazardous Locations. Such locations are defined in Article 500 of the National Fire Protection Association (NFPA) publication  NFPA 70 , otherwise known as the National Electrical Code. The transceiver has been recognized for use in these hazardous locations by two independent agencies Underwriters Laboratories (UL) and the Canadian Standards Association (CSA). The UL certification for the transceiver is as a Rec-ognized Component for use in these hazardous locations, in accordance with UL Standard 1604. The CSA Certifica-tion is in accordance with CSA STD C22.2 No. 213-M1987. UL/CSA Conditions of Approval: The transceiver is not acceptable as a stand-alone unit for use in the hazardous locations described above. It must either be mounted within another piece of equipment which is certified for hazardous locations, or installed within guidelines, or conditions of approval, as set forth by the approving agencies. These conditions of approval are as follows:The transceiver must be mounted within a separate enclosure which is suitable for the intended application.The antenna feedline, DC power cable and interface cable must be routed through conduit in accordance with the National Electrical Code. Installation, operation and maintenance of the transceiver should be in accordance with the transceiver’s installation manual, and the National Electrical Code.    (UL/CSA Notice continued on next page...) Tampering or replacement with non-factory components may adversely affect the safe use of the transceiver in haz-ardous locations, and may void the approval.  Professional installation required. The radio equipment described in this guide emits radio frequency energy. Although the power level is low, the concentrated energy from a direc-tional antenna may pose a health hazard. Do not allow people to come closer than 23 cm (9 inches) to the antenna when the transmitter is operating in indoor or outdoor environ-ments. More information on RF exposure is on the Internet at  www.fcc.gov/oet/info/documents/bulletins .RF Exposure
 viii iNET Series Reference Manual 05-2806A01, Rev. H A power connector with screw-type retaining screws as supplied by GE MDS must be used. Do not disconnect equipment unless power has been switched off or the area is known tobe non-hazardous.Refer to Articles 500 through 502 of the National Electrical Code (NFPA 70) for furtherinformation on hazardous locations and approved Division 2 wiring methods.  FCC Part 15 Notices The transceiver series complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device is specifically designed to be used under Section 15.247 of the FCC Rules and Regulations. Any unauthorized modification or changes to this device without the express approval of Microwave Data Systems may void the users authority to operate this device. Furthermore, the iNET Series is intended to be used only when installed in accordance with the instructions outlined in this manual. Failure to comply with these instructions may also void the users authority to operate this device.Part 15 rules also require that the Effective Isotropic Radiated Power (EIRP) from an GE MDS iNET Series installation not exceed 36 dBm. Refer to  Antenna & Feedline Selection  on Page 132 for more information. Industry Canada RSS Notices Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.To reduce potential radio interference to other users, the antenna type and its gain should be chosen so that the Equiv-alent Isotropic Radiated Power (EIRP) is not more than that permitted for successful communication.This device as been designed to operate with the antennas listed below, and having a maximum gain of 12 dB. Antennas not included in this list or having a gain greater than 12 dB are strictly prohibited for use with this device. The required antenna impedance is 50 ohms. Refer to Table 4-3 on Page 138 for a list of antennas acceptable for use with this transceiver. Manual Revision and Accuracy This manual was prepared to cover a specific version of firmware code. Accordingly, some screens and features may differ from the actual unit you are working with. While every reasonable effort has been made to ensure the accuracy of this publication, product improvements may also result in minor differences between the manual and the product shipped to you. If you have additional questions or need an exact specification for a product, please contact our Cus-tomer Service Team using the information at the back of this guide. In addition, manual updates can often be found on the GE MDS Web site at www.GEmds.com. Environmental Information The manufacture of this equipment has required the extraction and use of natural resources. Improper disposal may contaminate the environment and present a health risk due to hazardous substances contained within. To avoid dissem-ination of these substances into our environment, and to limit the demand on natural resources, we encourage you to use the appropriate recycling systems for disposal. These systems will reuse or recycle most of the materials found in this equipment in a sound way. Please contact GE MDS or your supplier for more information on the proper disposal of this equipment.  EXPLOSIONHAZARD!
 05-2806A01, Rev. H iNET Series Reference Manual 1 1 PRODUCT OVERVIEWAND APPLICATIONS 1 Chapter Counter Reset Paragraph Contents 1.1   ABOUT THIS MANUAL ............................................................... 3 1.1.1   Related Publication  .......................................................................3 1.2   PRODUCT DESCRIPTION ......................................................... 3 1.2.1   Model Offerings .............................................................................51.2.2   Differences Between iNET and iNET-II Models  ............................61.2.3   GE MDS P21 Protected Network (Redundant) Configuration  ......6 1.3   APPLICATIONS ........................................................................... 7 1.3.1   Wireless LAN  ................................................................................71.3.2   Point-to-Point LAN Extension  .......................................................81.3.3   Backhaul for Serial Radio Networks  .............................................81.3.4   Multiple Protocols and/or Services ................................................91.3.5   Wireless LAN with Mixed Services ..............................................101.3.6   Upgrading Older Wireless Network with Serial Interfaces  .....................................................................................10Replacing Legacy Wireless Products ............................................... 11Supplement legacy wireless network with IP services ..................... 111.3.7   High-Speed Mobile Data ............................................................. 11 1.4   NETWORK DESIGN CONSIDERATIONS ................................ 12 1.4.1   Extending Network Coverage with Repeaters  ............................ 12What is a Repeater System?............................................................ 12Option 1Using two transceivers to form a repeater station(back-to-back repeater) ....................................................................12Option 2Using the AP as a Store-and-Forward Packet Repeater...........................................................................................131.4.2   Protected Network Operation using Multiple Access Points  .......141.4.3   Collocating Multiple Radio Networks  ..........................................14The Network Name and the association process .............................14Can radio frequency interference (RFI) disrupt my wireless network?.15 1.5   CYBER SECURITY ................................................................... 15 1.6   ACCESSORIES ......................................................................... 17
 2 iNET Series Reference Manual 05-2806A01, Rev. H
 05-2806A01, Rev. H iNET Series Reference Manual 3 1.1 ABOUT THIS MANUAL This Reference Manual is designed for use by professional installers and technicians. It contains an in-depth description of the product, including installation, configuration, and troubleshooting details. 1.1.1 Related Publication A companion publication, the  GE MDS iNET Series Start-Up Guide  is also available (Part No. 05-2873A01). This smaller guide contains the essential information for installing the radio and placing it into opera-tion. This guide is recommended for those primarily involved in the installation and setup of the product. 1.2 PRODUCT DESCRIPTION The GE MDS iNET 900 transceiver (Figure 1-1) provides an easy-to-install wireless local area network (WLAN) service with long range and secure operation. It supports both Ethernet and serial data interface options at over-the-air data speeds of up to 1 Mbps (iNET-II) and 512 kbps (iNET).NOTE: For information on the GE MDS iNET 900 ENI, whichprovides expanded gateway and protocol conversion capabili-ties not found in the GE MDS iNET 900 (DF1 to EIP, andMODBUS to MODBUS TCP conversions), refer to the GEMDS iNET/ENI Supplement (05-4131A01).Invisible place holderFigure 1-1. The GE MDS iNET 900 TransceiverRugged Packaging The transceiver is housed in a compact and rugged cast-metal case that need only be protected from direct exposure to the weather. It contains a single printed circuit board with all necessary components for radio operation and data communications. The only user-serviceable compo-nent in the case is a fuse on the DC power input line.Simple Installation Most installations employ an omni-directional antenna at the Access Point (AP) location and a directional antenna at each Remote unit. The antenna is a vital link in the system and must be chosen and installed
4 iNET Series Reference Manual 05-2806A01, Rev. Hcorrectly. See “INSTALLATION PLANNING” on Page 129 for guid-ance on choosing suitable installation sites and antennas.For basic services, simply connect an antenna, connect your Ethernet LAN to the transceiver’s LAN port, apply primary power, set a few oper-ating parameters, and you are done. No license is required for operation in the U.S.A., Canada, and many other countries. Check requirements for your region before placing the transceiver in service.Secure Operation Data network security is a vital issue in today's wireless world. GE MDS iNET Series radios provide multiple tools to help you build a networkthat minimizes the risk of eavesdropping and unauthorized access. Someare inherent in the radio's operation, such as the use of 900 MHzspread-spectrum transmissions; others include data encryption, en-abling/disabling remote access channels, and password protection.Remember, security is not a one-step process that can simply be turned on and forgotten. It must be practiced and enforced at multiple levels, 24 hours-a-day and 7 days-a-week. See “CYBER SECURITY” on Page 15 for more information about the transceiver’s security tools.Robust Radio Operation The transceiver is designed for frequency-hopping spread-spectrum operation in the license-free 900 MHz Industrial, Scientific, and Med-ical (ISM) band. It can provide reliable communications at distances up to 25 miles (40 km) over favorable terrain, even in the presence of weak signals or interference. Frequency hopping allows the transceiver to avoid interference from other transmitters in the same band, and pro-vides frequency diversity for more reliable transmission. The over-the-air MAC increases reliability by adding retries to failed mes-sages.The iNET-II transceiver, which is certified to operate under DTS rules (hopping not required), also hops in order to achieve the same benefits that are realized with the iNET transceiver which is certified under FHSS rules.Flexible Services Users with a mixture of equipment having Ethernet and serial data inter-faces can choose to use one or two of the user-configurable serial ports through the use of a Remote Dual Gateway. This flexibility allows the transceiver to provide services in data networks that are being migrated from legacy serial/EIA-232-based hardware to the faster and more easily interfaced Ethernet world.Flexible Management Configuration, commissioning, troubleshooting and other maintenance activities can be done locally or remotely. Four different modes of access are available: local RS-232 console, local or remote Internet Pro-tocol (IP) access via Telnet or SSH, web browser (HTTP, HTTPS), and SNMP (v1/v2/v3). The text-based interface (RS-232 console Telnet and SSH) is implemented in the form of easy-to-follow menus, and the ter-minal server configuration includes a wizard to help you set up the units correctly.
05-2806A01, Rev. H iNET Series Reference Manual 5Transceiver Features The transceiver’s design makes the installation and configuration easy, while allowing for changes in the future.• Long Range—Up to 30 miles (48 km) nominal range in line-of-sight conditions. Repeater stations may be used to extend the operational range. (Refer to TECHNICAL SPECIFI-CATIONS on Page 158 for more detailed information on range.)• Industrial-Grade Product—Extended temperature range for trouble-free operation in extreme environments• Robust Radio Communications—Designed to operate in dense, high-interference environments• Robust Network Security—Prevents common attack schemes and hardware from gaining access or control of network. Com-mon attack events logged and reported by alarms.• High Speed—1 Mbps (iNET-II) is 100-times faster than 9.6 kbps radios. GE MDS iNET transceiver speed is 512 kbps.• Plug-and-Play Connectivity—Ethernet bridge configuration option requires minimal setup• Serial Ports—Gateway for serial-based equipment to IP/Ether-net networks with embedded terminal server. Site-to-site con-figurations are also possible.• Single hardware package provides configuration as Access Point or Remote1.2.1 Model OfferingsThe transceiver comes in two primary models—Access Point and Remote. Three types of Remote Gateways are available—the Ethernet Bridge, the Serial Gateway, and the Dual Gateway supporting both IP/Ethernet and serial services. Table 1-1 summarizes the different interface abilities for each type. A unit can be configured by the owner to operate as an Access Point or as a Remote with some restrictions. Only the Dual Gateway Remote units can be reconfigured as an Access Point. Ethernet Bridge and a Serial Gateway Remotes cannot be reconfigured as an Access Point unless they are first upgraded to Dual Gateway type. This is accom-plished with an “Authorization Key” purchased from the factory. Each one of these individual software keys is associated with the serial number of the corresponding unit.
6 iNET Series Reference Manual 05-2806A01, Rev. H1.2.2 Differences Between iNET and iNET-II ModelsThe iNET and iNET-II Transceivers, while similar in many respects, do have some important differences. The main differences are summarized in Table 1-2:Table 1-2. Transceiver Differences (iNET vs. iNET-II)NOTE: The GE MDS iNET and GE MDS iNET-II transceivers are notover-the-air compatible.1.2.3 GE MDS P21 Protected Network (Redundant) ConfigurationFor mission-critical applications, GE MDS also offers the Protected Network Station. This radio incorporates two iNET Series transceivers, two power supplies, and a switchover logic board that automatically selects between Transceiver A and Transceiver B as the active radio. Figure 1-2 shows a view of the protected chassis. For system-level information on this product, see GE MDS publication 05-4161A01.Table 1-1. Transceiver Models and Data Interface ServicesModel Type LAN1COM11COM2Access Point3N/A Yes Yes YesRemote… Ethernet Bridge2Yes No NoSerial Gateway2No Yes YesDual Gateway3Yes Yes YesNOTES 1. Provides access to the embedded Management System on all units.2. Can be upgraded to Dual Gateway with an Authorization Key.3. Can be configured as an Access Point or Dual Gateway through the embedded Management System.Characteristic iNET iNET-IIData Rate 256/512 kbps 512 kbps/1 MbpsFCC Certification TypeFHSS DTSEncryption RC4-128 AES-128Channel size 316.5 kHz 600 kHzChannel operation Zones ChannelsFirmware Specific for iNET Specific for iNET-II
05-2806A01, Rev. H iNET Series Reference Manual 7Invisible place holderFigure 1-2. GE MDS P21 Protected Network Station(incorporates two Transceivers, with Automatic Switchover)1.3 APPLICATIONSThe following sections provide illustrations of typical transceiver instal-lations. This is meant as an overview only. It is recommended that a net-work manager be involved in all installation planning activities.1.3.1 Wireless LANThe wireless LAN is the most common application of the transceiver. It consists of a central control station (Access Point) and one or more asso-ciated Remote units, as shown in Figure 1-3 on Page 8. A LAN provides communications between a central WAN/LAN and remote Ethernet segments. The operation of the radio system is transparent to the com-puter equipment connected to the transceiver.The Access Point is positioned at a location from which it can commu-nicate with all of the Remote units in the system. Commonly, this is a high location on top of a building or communications tower. Messages are exchanged at the Ethernet level. This includes all types of IP traffic.A Remote transceiver can only talk over-the-air to an Access Point unit (AP). Peer-to-peer communications between Remotes can only take place indirectly via the AP. In the same fashion, an AP can only talk over-the-air to associated Remote units. Exception: Two APs can com-municate with each other “off-the-air” through their Ethernet connectors using a common LAN/WAN.
8 iNET Series Reference Manual 05-2806A01, Rev. HInvisible place holderFigure 1-3. Typical Wireless LAN1.3.2 Point-to-Point LAN ExtensionA point-to-point configuration (Figure 1-4) is a simple arrangement consisting of an Access Point and a Remote unit. This provides a com-munications link for the transfer of data between two locations.Invisible place holderFigure 1-4. Typical Point-to-Point Link1.3.3 Backhaul for Serial Radio NetworksOne of the primary design features of the transceiver is to provide a path for serial devices to migrate to IP/Ethernet. Many radio networks in operation today still rely on serial networks at data rates of 9600 bps or less. These networks can use the transceiver as a means to continue using the serial service, while allowing the rest of the infrastructure to migrate to an IP format.A Remote transceiver using one serial port for the data stream, and the other for network-wide diagnostics can support operational radio net-works built with GE MDS serial-based radios, such as GE MDS x790/x710, GE MDS TransNET and others. In the case of radios using a single port for data and diagnostics, the capabilities are doubled. The data streams are delivered to an IP socket in an application, or in serial format using the Access Point.RemoteRemoteAccess PointRemoteRemoteLANLANWAN/LANLANLANLAN/WANAccess Point RemoteLAN
05-2806A01, Rev. H iNET Series Reference Manual 9Invisible place holderFigure 1-5. Backhaul Network1.3.4 Multiple Protocols and/or ServicesPrior to the iNET Series, two radios were often used to service two dif-ferent types of devices (typically connected to different SCADA hosts). An iNET or iNET-II radio provides this functionality with a single remote radio. Each of the two serial ports can be connected via IP to dif-ferent SCADA hosts, transporting different (or the same) protocols. Both data streams are completely independent and the transceiver pro-vides seamless simultaneous operation as shown in. Invisible place holderFigure 1-6. Multiple Protocol NetworkBy using a single radio, the cost of deployment is cut in half. Beyond requiring only one radio instead of two, the biggest cost reduction comes from using half of the required infrastructure at the remote site: one DataDataMDS 4790MasterMDS 9790MasterMDS 9810MasterDiagnosticsDataDiagnosticsDiagnosticsMDS 4710 RemoteNMS ControlPointSCADA HostModbus/IPHUB Access PointMDS 4710 RemoteMDS 9710 RemoteMDS 9710 RemoteMDS 9810 RemoteMDS 9810 RemoteRemote SerialRemote SerialRemote SerialNETWORKROUTERROUTERSerialDeviceSerialDeviceSerialDeviceSerialDeviceSerialDeviceSerialDeviceNETview SCADA HostTotal FlowAccess PointRemote SerialRemote SerialSCADA HostModbus/IPRemote SerialAccess PointRTUFlow MeterEIA-232EIA-232EIA-232EIA-232EIA-232EIA-232ROUTERHUBSerialDeviceSerialDeviceSerialDeviceSerialDeviceHUBHUBHUBWAN
10 iNET Series Reference Manual 05-2806A01, Rev. Hantenna, one feedline, one lightning protector and ancillary hardware. Other cost reductions come from the system as a whole, such as reduced management requirements. And above all, the radio offers potential for future applications that run over Ethernet and IP, such as video for remote surveillance.1.3.5 Wireless LAN with Mixed ServicesThe iNET transceiver is an excellent solution for a long-range industrial wireless LAN. It offers several advantages over commercial solutions—primarily improved performance over extended distances. The rugged construction of the radio and its extended temperature range make it an ideal solution even in harsh locations. In extreme environments, a simple NEMA enclosure is sufficient to house the unit.The transceiver trades higher speed for longer range. Commercial 802.11a/b/g solutions are designed to provide service to relatively small areas such as offices, warehouses and homes. They provide high data rates but have limited range. The iNET transmits at a higher power level, uses a different frequency band, has higher sensitivity, and a narrower channel to concentrate the radio energy and reach farther distances. It is designed for industrial operation from the ground up.IP-based devices that may be used with the transceiver include a new breed of more powerful Remote Terminal Units (RTUs) and Program-mable Logic Controllers (PLCs). These, as well as other devices, may be used in applications ranging from SCADA/telemetry monitoring, web-based video, security monitoring, and voice over IP. Figure 1-7 shows a typical wireless IP network.Invisible place holderFigure 1-7. Extended-Range LAN with Mixed Applications1.3.6 Upgrading Older Wireless Network with Serial InterfacesMillions of wireless data products have been sold in the last two decades for licensed and license-free operation, many of them manufactured by NMS ControlPointSCADA HostModbus/IPAccess PointRemote BridgePrinterRemote BridgeIP CameraIP/Ethernet DeviceIP/Ethernet DeviceIP/Ethernet Device
05-2806A01, Rev. H iNET Series Reference Manual 11Microwave Data Systems. There are several ways that these systems can benefit from incorporating iNET equipment. The chief advantages are interface flexibility (serial and Ethernet in one unit), and higher data throughput. By taking advantage of its built-in serial and Ethernet inter-faces, the transceiver is well suited to replace leased lines, dial-up lines, or existing MAS 900 MHz data transceivers.Replacing Legacy Wireless ProductsIn most cases, legacy radio transceivers supporting serial-interface equipment can be replaced with iNET transceivers. Legacy equipment can be connected to the transceiver through the COM1 or COM2 port with a DB-25 to DB-9 cable wired for EIA-232 signaling. The COM2 port supports all standard EIA-232 signaling and acts as a data-terminal equipment device (DTE).NOTE: Several previous GE MDS-brand products had non-standardsignal lines on their interface connectors (to control sleep func-tions and alarm lines, for example). These special functions arenot provided nor supported by the iNET Series. Consult equip-ment manuals for complete pinout information.Supplement legacy wireless network with IP servicesThe iNET Dual Gateway model can support up to two serial devices and one Ethernet connection at the same time. The serial interfaces (COM1 and COM2) operate in two different modes: Connectionless UDP and connection-oriented TCP.In the UDP mode, the transceiver supports point-to-multipoint serial-port to serial-port connectivity. In the TCP mode, it supports point-to-point Ethernet/IP to serial port connectivity.For further details on the transceiver’s Serial Gateway interface modes, see “CONFIGURING THE SERIAL PORTS” on Page 60.1.3.7 High-Speed Mobile DataThe iNET radios support high-speed data communications in a mobile environment. Remote radios roam between different access points, pro-viding seamless transitions and continuous coverage. For additional information on configuring a mobile network, refer to Mobility Config-uration Menu on Page 58.
12 iNET Series Reference Manual 05-2806A01, Rev. H1.4 NETWORK DESIGN CONSIDERATIONS1.4.1 Extending Network Coverage with RepeatersWhat is a Repeater System?A repeater works by re-transmitting data from outlying remote sites to the Access Point and vice-versa. It introduces some additional end-to-end transmission delay but provides longer-range connectivity.In some geographical areas, obstacles can make communications diffi-cult. These obstacles are commonly large buildings, hills, or dense foliage. These obstacles can often be overcome with a repeater station. Option 1—Using two transceivers to form a repeater station(back-to-back repeater)Although the range between transceivers can be a nominal 40 km (25 miles) over favorable terrain, it is possible to extend the range consider-ably by connecting two units together at one site in a “back-to-back” fashion to form a repeater, as shown in Figure 1-8. This arrangement should be used whenever the objective is to utilize the maximum range between stations. In this case, using high-gain Yagi antennas at each location will provide more reliable communications than their counter-parts—omnidirectional antennas.Invisible place holderFigure 1-8. Typical LAN with a Repeater LinkOverview Two transceivers may be connected “back-to-back” through the LAN Ports to form a repeater station. (The cable must be a “cross-over” Ethernet cable for this to work). This configuration is sometimes required in a network that includes a distant Remote that would other-wise be unable to communicate directly with the Access Point station due to distance or terrain.The geographic location of a repeater station is especially important. A site must be chosen that allows good communication with both the Access Point and the outlying Remote site. This is often on top of a hill, building, or other elevated terrain from which both sites can be “seen” Access PointRemoteRemoteRemoteRemoteAccessPointLAN/WANREPEATERCrossover CableLANLANLANEthernetPOINT-TO-POINT LINK
05-2806A01, Rev. H iNET Series Reference Manual 13by the repeater station antennas. A detailed discussion on the effects of terrain is given in Section 4.1.2, Site Selection (beginning on Page 131).The following paragraphs contain specific requirements for repeater systems.Antennas Two antennas are required at this type of repeater station—one for each radio. Measures must be taken to minimize the chance of interference between these antennas. One effective technique for limiting interfer-ence is to employ vertical separation. In this arrangement, assuming both are vertically polarized, one antenna is mounted directly over the other, separated by at least 10 feet (3 Meters). This takes advantage of the minimal radiation exhibited by most antennas directly above and below their driven elements.Another interference reduction technique is to cross-polarize the repeater antennas. If one antenna is mounted for polarization in the ver-tical plane, and the other in the horizontal plane, an additional 20 dB of attenuation can be achieved. (Remember that the corresponding stations should use the same antenna orientation when cross-polarization is used.)Network Name The two radios that are wired together at the repeater site must have dif-ferent network names.Option 2—Using the AP as a Store-and-Forward Packet RepeaterA wireless network can be extended through the use of an alternate arrangement using the Access Point as a repeater to re-transmit the sig-nals of all stations in the network. The repeater is a standard transceiver configured as an Access Point, and operating in Store and Forward mode. (See Figure 1-9.)Invisible place holderFigure 1-9. Typical network with store-and-forward repeaterAs with the conventional repeater described in Option 1 above, the loca-tion of a store and forward repeater is also important. A site must be chosen that allows good communication with both the Access Point and the outlying Remote site. This can be on the top of a hill, building, or other elevated terrain from which all sites can be “seen” by the repeater RemoteRemoteRemoteRemoteAccess PointLAN/WANREPEATERLANLANLAN
14 iNET Series Reference Manual 05-2806A01, Rev. Hstation antenna. A detailed discussion on the effects of terrain is given in Section 4.1.2, Site Selection (beginning on Page 131)1.4.2 Protected Network Operation using Multiple Access PointsAlthough GE MDS transceivers have a very robust design and have undergone intensive testing before being shipped, it is possible for iso-lated failures to occur. In mission-critical applications, down time can be virtually eliminated by using some, or all, of the following configu-rations:In a point-to-multipoint scenario, the Access Point services multiple remotes. A problem in the Access Point will have an effect on all remotes, since none will have access to the network. When operation of the network does not tolerate any down time, it is possible to set up a protected configuration for the Access Point to greatly reduce the possi-bility of this occurrence.Two or more Access Points can be configured with the same Network Name and kept active simultaneously, each with its own independent antenna. In this scenario, Remotes will associate with either one of the available Access Points. In case of a failure of one of the AP’s the Remotes will quickly associate with another of the remaining Access Points re-establishing connectivity to the end devices.The Access Points are unaware of the existence of the other AP’s. Because the hopping algorithm uses both the Network Name and the Wireless MAC address of the AP to generate the hopping pattern, mul-tiple AP’s can coexist—even if they use the same network name. The collocated AP’s will be using different hopping patterns and frequencies the great majority of the time. Although some data collisions will occur, the wireless-MAC is built to tolerate and recover from such occurrences with minimal degradation.1.4.3 Collocating Multiple Radio NetworksMany networks can operate in relatively close physical proximity to one another provided reasonable measures are taken to assure the radio signal of one Access Point is not directed at the antenna of the second Access Point.The Network Name and the association processThe Network Name is the foundation for building individual radio net-works. It is part of a beacon signal broadcast by the Access Point (AP) to any Remote units with the same Network Name. Remotes that join the network are referred to as being “associated” with the Access Point unit. Multiple APs with the same Network Name should be used with care. Using the same Network Name in multiple APs may result in Remotes
05-2806A01, Rev. H iNET Series Reference Manual 15associating with undesired APs and preventing data exchange from occurring as planned.The use of a different Network Name does not guarantee an interfer-ence-free system. It does however, assure that only data destined for a unique network is passed through to that network.Co-Location for Multiple Networks It may be desirable to co-locate Access Points at one location to take advantage of an excellent or premium location that can serve two inde-pendent networks. Each network should have unique Network Name and each AP unit’s antenna should be provided as much vertical separa-tion as is practical to minimize RFI.NOTE: All transceivers are shipped with the Network Name set to“Not Programmed.” The Network Name must be programmedin order to pass data and begin normal operations. Can radio frequency interference (RFI) disrupt my wireless network?When multiple radio networks operate in close physical proximity to other wireless networks, individual units may not operate reliably under weak signal conditions and may be influenced by strong radio signals in adjacent bands. This radio frequency interference cannot be predicted with certainty, and can only be determined by experimentation. If you need to co-locate two units, start by using the largest possible vertical antenna separation between the two AP antennas on the same support structure. If that does not work, consult with your factory representative about other techniques for controlling radio frequency interference between the radios. (See “A Word About Radio Interference” on Page 136 for more details.)1.5 CYBER SECURITYToday the operation and management of an enterprise is becoming increasing dependent on electronic information flow. An accompanying concern becomes the cyber security of the communication infrastructure and the security of the data itself.
16 iNET Series Reference Manual 05-2806A01, Rev. HThe transceiver is capable of dealing with many common security issues. Table 1-3 profiles security risks and how the transceiver pro-vides a solution for minimizing vulnerability. Table 1-3. Security Risk ManagementSecurity Vulnerability GE MDS Cyber Security  SolutionUnauthorized access to the backbone network through a foreign remote radio • 802.1x authentication• Approved Remotes List (local)Only those remotes included in the AP list will associate“Rogue” AP, where a foreign AP takes control of some or all remote radios and thus remote devices• 802.1x authentication• Approved AP ListA remote will only associate to those AP included in its local authorized list of APDictionary attacks, where a hacker runs a program that sequentially tries to break a password.• Failed-login lockdown After 3 tries, the transceiver ignores login requests for 5 minutes. Critical event reports (traps) are generated as well.Denial of service, where Remote radios could be reconfigured with bad parameters bringing the network down.•Remote login with SSH or HTTPS•Local console login•Disabled HTTP & Telnet to allow only local management servicesAirsnort and other war-driving hackers in parking lots, etc. •900 MHz operation is not interoperable with standard 802.11b wireless cards•The transceiver cannot be put in a promiscuous mode•Proprietary data framingEavesdropping, intercepting messages •AES-128 encryption (iNET-II)•RC4-128 encryption (iNET)Key cracking software • Automatic Rotating Key algorithmReplaying messages • Automatic Rotating Key algorithm
05-2806A01, Rev. H iNET Series Reference Manual 171.6 ACCESSORIESThe transceiver can be used with one or more of the accessories listed inTable 1-4. Contact the factory for ordering details.Unprotected access to configuration via SNMPv1 •Implement SNMPv3 secure operationIntrusion detection •Provides early warning via SNMP through critical event reports (unauthorized, logging attempts, etc.)•Unauthorized AP MAC address detected at Remote•Unauthorized Remote MAC address detected at AP•Login attempt limit exceeded (Accessed via: Telnet, HTTP, or local)•Successful login/logout (Accessed via: Telnet, HTTP, or local)Table 1-3. Security Risk ManagementSecurity Vulnerability GE MDS Cyber Security  SolutionTable 1-4. Accessories  Accessory Description GE MDS Part No.AC Power Adapter KitA small power supply module designed for continuous service. UL approved. Input: 120/220; Output: 13.8 Vdc @ 2.5 A01-3682A02Omni- Directional AntennasRugged antennas well suited for use at Access Point installations. Consult with your factory Sales Representative for detailsCall factoryYagi Antenna(Directional)Rugged antennas well suited for use at Remote installations. Consult with your factory Sales Representative for details.Call factoryTNC Male-to-N Female Adapter One-piece RF adaptor plug. 97-1677A161TNC Male-to-N Female Adapter CableShort length of coaxial cable used to connect the radio’s TNC antenna connector to a Type N commonly used on large diameter coaxial cables.97-1677A159(3 ft./1m)97-1677A160(6 ft./1.8m)Ethernet RJ-45 Crossover Cable (CAT5)Cable assembly used to cross-connect the Ethernet ports of two transceivers used in a repeater configuration. (Cable length ≈ 3 ft./1M)97-1870A212-Pin Power PlugMates with power connector on transceiver. Screw terminals provided for wires, threaded locking screws to prevent accidental disconnect.73-1194A39
18 iNET Series Reference Manual 05-2806A01, Rev. HEthernet RJ-45 Straight-thru Cable (CAT5)Cable assembly used to connect an Ethernet device to the transceiver. Both ends of the cable are wired identically.(Cable length ≈ 3 ft./1M)97-1870A20EIA-232 Shielded Data CableShielded cable terminated with a DB-25 male connector on one end, and a DB-9 female on the other end. Two lengths available (see part numbers at right).97-3035L06(6 ft./1.8m)97-3035L15(15 ft./4.6m)EIA-232 Shielded Data CableShielded cable terminated with a DB-9 male connector on one end, and a DB-9 female on the other end, 6 ft./1.8m long.97-1971A03Fuse Small, board-mounted fuse used to protect against over-current conditions.29-1784A03Flat-Surface Mounting Brackets & ScrewsBrackets: 2˝ x 3˝ plates designed to be screwed onto the bottom of the unit for surface-mounting the radio.82-1753-A01Screws: 6-32/1/4˝ with locking adhesive. (Industry Standard MS 51957-26)70-2620-A01DIN Rail Mounting BracketBracket used to mount the transceiver to standard 35 mm DIN rails commonly found in equipment cabinets and panels.03-4022A02COM2 Interface AdapterDB-25(F) to DB-9(M) shielded cable assembly (6 ft./1.8 m) for connection of equipment or other EIA-232 serial devices previously connected to “legacy” units. (Consult factory for other lengths and variations.)97-3035A06GE MDS NETview MS SoftwarePC-based network management system for new-generation GE MDS transceivers. Allows radio control and diagnostics in a hierarchal map perspective.03-3938A01Bandpass Filter Antenna system filter that helps eliminate interference from nearby paging transmitters.20-2822A02Ethernet Surge SuppressorSurge suppressor for protection of Ethernet port against lightning.29-4018A01Table 1-4. Accessories   (Continued)Accessory Description GE MDS Part No.
05-2806A01, Rev. H iNET Series Reference Manual 192EMBEDDED MANAGEMENT SYSTEM2 Chapter Counter Reset ParagraphContents2.1   INTRODUCTION ....................................................................... 232.1.1   Differences in the User Interfaces ...............................................232.2   ACCESSING THE MENU SYSTEM .......................................... 252.2.1   Methods of Control ......................................................................262.2.2   PC Connection & Log In Procedures  ..........................................262.2.3   Navigating the Menus  .................................................................31Via Terminal Telnet or SSH SessionsRecommended for first-time log-in ...................................................31Navigating via Web Browser ............................................................312.3   BASIC DEVICE INFORMATION................................................ 322.3.1   Starting Information Screen  ........................................................322.3.2   Main Menu  ..................................................................................342.3.3   Configuring Basic Device Parameters  ........................................35Device Information............................................................................35Device Names Menu ........................................................................362.4   CONFIGURING NETWORK PARAMETERS ............................ 372.4.1   Network Configuration Menu  ......................................................372.4.2   Network Interface Configuration Menu  .......................................39Virtual LAN in iNET-II and iNET........................................................40Configuring for Operation with VLAN ...............................................41Configuring the IP Address when VLAN Status is Enabled..............42Configuring the IP Address When VLAN Status is Disabled ............ 432.4.3   Ethernet Port Configuration Menu  ..............................................452.4.4   DHCP Server Configuration ........................................................462.4.5   SNMP Agent Configuration  .........................................................472.4.6   Prioritized AP Configuration Submenu ........................................492.5   RADIO CONFIGURATION ........................................................ 512.5.1   Radio Configuration Menu  ..........................................................512.5.2   Channel Config Menu  .................................................................542.5.3   Skip Zones Menu  ........................................................................552.5.4   Auto Data Rate Configuration Menu  ...........................................562.5.5   Mobility Configuration Menu  .......................................................58Additional Considerations for Mobile Operation ...............................59At Every Mobile (Remote) Radio ......................................................59
20 iNET Series Reference Manual 05-2806A01, Rev. HAt Every AP Radio ............................................................................602.6   CONFIGURING THE SERIAL PORTS ...................................... 602.6.1   Overview  .....................................................................................60Com1 Port—Dual Purpose Capability................................................ 61TCP vs. UDP ....................................................................................61Serial Encapsulation......................................................................... 61TCP Client vs. TCP Server ............................................................... 62UDP Multicast...................................................................................62PPP ..................................................................................................63Data Buffering...................................................................................63Implementing Configuration Changes ..............................................63Serial Configuration Wizard.............................................................. 632.6.2   Serial Data Port Configuration Menu  .......................................... 632.6.3   Configuring for UDP Mode ..........................................................642.6.4   Configuring for TCP Mode  ..........................................................682.6.5   Configuring for PPP Mode  ..........................................................702.6.6   IP-to-Serial Application Example .................................................712.6.7   Point-to-Multipoint IP-to-Serial Application Example ...................722.6.8   Point-to-Point Serial-to-Serial Application Example  ....................742.6.9   Combined Serial and IP Application Example .............................75Operation and Data Flow..................................................................752.6.10   Virtual LAN in iNET-II and iNET  ................................................77Configuring for Operation with VLAN ...............................................782.7   CYBER SECURITY CONFIGURATION .................................... 782.7.1   Device Security  ...........................................................................792.7.2   Wireless Security  ........................................................................80Local AuthenticationApproved Remotes/Access Points List Submenu ..........................................................................................812.7.3   RADIUS Configuration  ................................................................82Operation of Device Authentication .................................................. 83Operation of User Authentication......................................................832.7.4   RADIUS Configuration  ................................................................842.7.5   Certificate Management (Remote transceivers only) ..................842.8   PERFORMANCE VERIFICATION............................................. 852.8.1   RSSI by Zone Menu (Remotes Only) ..........................................872.8.2   Event Log Menu ..........................................................................88Time and Date ..................................................................................88View Current Alarms.........................................................................90View Event Log.................................................................................912.8.3   Packet Statistics Menu ................................................................91Wireless Packet Statistics ................................................................91Ethernet Packet Statistics.................................................................92Packets Received by Zone............................................................... 932.8.4   Wireless Network Status (Remotes Only) ...................................94The Transceivers Association Process ............................................94
05-2806A01, Rev. H iNET Series Reference Manual 21The Wireless Network Status Screen (Remotes Only).....................952.8.5   Remote Listing Menu (Access Points Only)  ...............................962.8.6   Endpoint Listing Menu (Access Points Only)  ..............................972.8.7   Remote Performance Listing Menu (Access Points Only)  .............................................................................982.8.8   Serial Data Statistics Menu .........................................................992.9   MAINTENANCE......................................................................... 992.9.1   Reprogramming Menu  ..............................................................100Upgrading the Firmware .................................................................102Error Messages During File Transfers............................................1042.9.2   Configuration Scripts Menu .......................................................105How Configuration Files Work ........................................................105Sample of Configuration Script File ................................................106Editing Configuration Files..............................................................1072.9.3   Authorization Keys Menu  .......................................................... 1082.9.4   Change the Type of Remote  .....................................................1082.9.5   Auto-Upgrade/Remote-Reboot Menu  ....................................... 108Firmware Upgrade (with AP Acting as a TFTP Server) ..................1092.9.6   Radio Test Menu  ....................................................................... 1102.9.7   Ping Utility Menu  ....................................................................... 1112.9.8   Reset to Factory Defaults .......................................................... 111Password Reset ............................................................................. 111
22 iNET Series Reference Manual 05-2806A01, Rev. H
05-2806A01, Rev. H iNET Series Reference Manual 232.1 INTRODUCTIONThe transceiver’s embedded management system is accessible through various data interfaces. These include the COM1 (serial) port, LAN (Ethernet) port, and via SNMP. Essentially the same capabilities are available through any of these paths. For SNMP management, the transceiver is compatible with GE MDS NETview MS™ software. Refer to GE MDS publication 05-2973A01 for more information on this tool. For support of other SNMP software, a set of MIB files is available for download from the GE MDS Web site at www.GEmds.com. A brief summary of SNMP commands can be found at SNMP Agent Configuration  section on Page 47 of this manual.The transceiver’s Management System and its functions are divided into the following menu groups:•Section 2.3, BASIC DEVICE INFORMATION (beginning on Page 32)•Section 2.4, CONFIGURING NETWORK PARAMETERS (beginning on Page 37)•Section 2.5, RADIO CONFIGURATION (beginning on Page 51)•Section 2.6, CONFIGURING THE SERIAL PORTS (beginning on Page 60)•Section 2.7, CYBER SECURITY CONFIGURATION (begin-ning on Page 78)•Section 2.8, PERFORMANCE VERIFICATION (beginning on Page 85)•Section 2.9, MAINTENANCE (beginning on Page 99)Each of these sections has a focus that is reflected in its heading. The section you are now reading provides information on connecting to the Management System, how to navigate through it, how it is structured, and how to perform top-level configuration tasks. Figure 2-1 on the fol-lowing page shows a top-level view of the Management System (MS). 2.1.1 Differences in the User InterfacesThere are slight differences in navigation, but for the most part, the con-tent is the same among different user interfaces. You will find a few dif-ferences in capabilities as the communications tool is driven by limitations of the access channel. Below are examples of the Starting Information Screen seen through a terminal and a Web-browser, respec-tively.
24 iNET Series Reference Manual 05-2806A01, Rev. H• Bolded items indicate a menu selection• Spacebar used to make some menu selections• AP = Access Point Only• RM = Remote OnlyDevice SecurityDevice ModeNetwork NameSNTP ServerMax. Remotes (AP)Database Timeout (AP)Database Logging (AP)Interface Config.Ethernet Port Config.DHCP Server Config.SNMP Agent Config.Rem-Rem BridgingPrioritized AP Config.NetworkConfigurationRadioConfigurationSerial GatewayConfigurationDeviceInformation Maintenance/ToolsSecurityConfigurationReprogrammingConfigurationScriptsAuthorization KeyMAIN MENURF OutputPowerData Rate (RM)Compression (AP)Dwell Time (AP)Beacon Period (AP)PerformanceInformationNOTES• Chart shows top-level view only. Details are given on the following pages.• Not all items are user-configurable• Some menu items depend on the Device Mode selectedRTS ThresholdRF HoppingFormat (AP)Skip Zones (AP)Some modelsRSSI Threshold(RM)SNR Threshold(RM)SeamlessInter-Frame Delay(UDP Point-to-Pointexample shown)Serial NumberHardware VersionFirmware VersionConsole Baud RateUptimeModel NumberDate FormatTimeUTC Time OffsetDateDevice NamesLogin StatusWireless SecurityRADIUS Config.Serial ModeFlow ControlRF Power OutputSignal-to-NoiseRSSIActual Data RateRSSI By ZoneEvent LogPacket StatisticsRemote Listing (AP)Endpoint Listing (AP)Remote Perf.Listing (AP)Radio TestPing UtilityReset to FactoryDefaultsConfigurationData Baud RatePacket Redund.Time to LiveLocal IP PortMulticast IP PortMulticast IP Addr.IP ProtocolStatusCOM1 & COM2Serial Data PortSerial Config.WizardFragmentationThresholdHop Pattern Seed (AP)Auto Data Rate Config.Mobility Config.Channel Config.Auto Upgrade/RemoteRebootFigure 2-1. Embedded Management System—Top-level Flowchart
05-2806A01, Rev. H iNET Series Reference Manual 25Figure 2-2. View of MS with a text-based program—(Terminal Emulator shown—Telnet has similar menu structure)Invisible place holderFigure 2-3. View of the MS with a Browser(Selections at left provide links to the various menus)2.2 ACCESSING THE MENU SYSTEMThe radio has no external controls. All configuration, diagnostics and control is performed electronically using a connected PC. This section explains how to connect a PC, log into the unit, and gain access to the built-in menu screens.
26 iNET Series Reference Manual 05-2806A01, Rev. H2.2.1 Methods of ControlThe unit’s configuration menus may be accessed in one of several ways: •Local Console—This is the primary method used for the exam-ples in this manual. Connect a PC directly to the COM 1 port using a serial communications cable and launch a terminal com-munications program such as HyperTerminal. This method pro-vides text-based access to the unit’s menu screens. Console control is a hardware-based technique, and is intended for local use only.•Telnet or SSH*—Connect a PC to the unit’s LAN port, either directly or via a network, and launch a Telnet session. This method provides text-based access to the unit’s menu screens in a manner similar to a Local Console session. Telnet sessions may be run locally or remotely through an IP connection. •Web Browser*—Connect a PC to the unit’s LAN port, either directly or via a network, and launch a web browser session (i.e., Internet Explorer, Netscape, etc.) This method provides a graphical representation of each screen, just as you would see when viewing an Internet website. The appearance of menu screens differs slightly from other methods of control, but the content and organization of screen items is similar. Web browser sessions may be run locally or remotely via the Inter-net.*     Telnet, SSH and Web Browser sessions require the use of a straight-through or crossover Ethernet cable, depending on the whether the PC-to-radio connection is made directly, or through an Ethernet switch. For direct connection, a crossover cable is required; For connection using an Ethernet switch, a straight-through type is needed.Cable type can be identified as follows: Hold the two cable ends side-by-side and in the same plug orientation (i.e., both locking tabs up or down). Now look at the individual wire colors on each plug. If the wires on both plugs are ordered in the same sequence from left to right, the cable is a straight-through type. If they are not in the same order, it may be a crossover cable, or it may be wired for some other application. Refer to DATA INTERFACE CONNECTORS on Page 155 for detailed pinout information.2.2.2 PC Connection & Log In ProceduresThe following steps describe how to access the radio’s menu system. These steps require a PC to be connected to the unit’s COM 1 or LAN port as shown in Figure 2-4.
05-2806A01, Rev. H iNET Series Reference Manual 27Invisible place holderFigure 2-4. PC Configuration SetupStarting a Local Console Session (Recommended for first-time log-in)1. Connect a serial communications cable between the PC and the unit’s COM 1 port. If necessary, a cable may be constructed for this purpose as shown in Figure 2-5.Invisible place holderFigure 2-5. Serial Communications Cable (RJ-11 to DB-9)(Maximum Recommended Cable Length 50 Feet/15 meters)2. Launch a terminal emulation program such as HyperTerminal and configure the program with the following settings: • 19,200 bps data rate• 8 data bits, no parity• One stop bit, and no flow-control• Use ANSI or VT100 emulation.TIP: The HyperTerminal communications program can be accessed on most PCs by selecting this menu sequence: Start>>Programs>>Accesso-ries>>Communications>>HyperTerminal.NOTE: Early versions of PuTTY might not operate when using SSHto connect to the transceiver. However, beta versions 0.59 andlater do work properly. Both the latest released and the latestdevelopment snapshot can be downloaded from:www.chiark.greenend.org.uk/~sgtatham/putty/.NOTE: If the unit is powered-up or rebooted while connected to aterminal, you will see a series of pages of text informationrelating to the booting of the unit’s microcomputer. Wait forthe log-in screen before proceeding.Configuration PCLANUSBCOM1 COM2 COM3 PWRTo COM1 or LAN Port(See Text)Serial or EthernetCrossover Cable(See Text)
28 iNET Series Reference Manual 05-2806A01, Rev. H3. Press the   key to receive the login: prompt. 4. Enter the username (default username is iNET or iNET-II, in accor-dance with radio model). Press  .5. Enter your password (default password is admin). (For security, your password keystrokes do not appear on the screen.) Press  .NOTE: Passwords are case sensitive. Do not use punctuation markcharacters. You may use up to eight alpha-numeric characters.The unit responds with the Starting Information Screen (Figure 2-6). From here, you can review basic information about the unit or press G to proceed to the Main Menu.Invisible place holderFigure 2-6. Starting Information Screen—Local Console Session(Telnet has similar menu structure)Starting a Telnet Session NOTE: This method requires that you know the IP address of the unitbeforehand. If you do not know the address, use the LocalConsole method (above) and access the Starting InformationScreen. The address is displayed on this screen.1. Connect a PC to the unit’s LAN port, either directly or via a network. If connecting directly, use an Ethernet crossover cable; if connecting via a network, use a straight-through cable. The LAN LED lights to indicate an active connection.ENTERENTERENTER
05-2806A01, Rev. H iNET Series Reference Manual 29NOTE: When using Ethernet to access the unit, it may be necessary tochange your computer’s IP access to be compatible with theradio IP address. You can identify or verify the unit’s IPaddress by using a Local Console session to communicate withthe radio through its COM 1 Port and viewing the StartingInformation Screen.2. Start the Telnet program on your computer targeting the IP address of the unit to which you are connected. and press  .TIP: A Telnet session can be started on most PCs by selecting: Start>>Programs>>Accessories>>Command Prompt. At the command prompt window, type the word telnet, followed by the unit’s IP address (e.g., telnet 10.1.1.168). Press   to receive the Telnet log in screen.NOTE: Never connect multiple units to a network with the same IPaddress. Address conflicts will result in improper operation.3. Enter your username (default username is iNET or iNET-II, in accor-dance with radio model). Press  . Next, the Password: prompt appears. Enter your password (default password is admin). (For security, your password keystrokes will not appear on the screen.) Press  .The unit responds with a Starting Information Screen (see Figure 2-6). From here, you can review basic information about the unit or press G to proceed to the Main Menu.NOTE: Passwords are case sensitive. Do not use punctuation markcharacters. You may use up to eight alpha-numeric characters.Starting a Web Browser Session NOTE: Web access requires that you know the IP address of the unityou are connecting to. If you do not know the address, start aLocal Console session (see Starting a Local Console Session(Recommended for first-time log-in) on Page 27) and accessthe Starting Information Screen. The IP address is displayedon this screen.1. Connect a PC to the unit’s LAN port, either directly or via a network. If connecting directly, use an Ethernet crossover cable; if connecting via a network, use a straight-through cable. The LAN LED lights to indicate an active connection.2. Launch a Web-browser session on your computer (i.e., Internet Explorer, Netscape Navigator, etc.).ENTERENTERENTERENTER
30 iNET Series Reference Manual 05-2806A01, Rev. H3. Type in the unit’s IP address and press  .4. A log-in screen is displayed (Figure 2-7) where you enter a user name and password to access the unit’s menu system. Note that the default entries are made in lower case. (Default username is iNET or iNET-II, in accordance with radio model; Default Password is admin).Invisible place holderFigure 2-7. Log-in Screen when using a Web BrowserNOTE: Passwords are case sensitive. Do not use punctuation markcharacters. You may use up to eight alpha-numeric characters.5. Click OK. The unit responds with a startup menu screen similar to that shown in Figure 2-8. From here, you can review basic informa-tion about the unit or click on one of the menu items at the left side of the screen.Invisible place holderFigure 2-8. Starting Information Screen—Web Browser ExampleENTERiNET
05-2806A01, Rev. H iNET Series Reference Manual 312.2.3 Navigating the MenusVia Terminal Telnet or SSH SessionsRecommended for first-time log-inLocal Console Telnet and SSH sessions use multi-layered text menu systems that are nearly identical. To move further down a menu tree, you type the letter assigned to an item of interest. This takes you to an associated screen where settings may be viewed, or changed. In most cases, pressing the   key moves the screen back one level in the menu tree.In general, the top portion of menu screens show read-only information (with no user selection letter). The bottom portion of the screen contains parameters that can be selected for further information, alteration of values, or to navigate to other submenus.When you arrive at a screen with user-controllable parameter fields, you select the menu item by pressing an associated letter on the keyboard. If there is a user definable value, the field will clear to the right of the menu item and you can type in the value you wish to use. Follow this action by pressing the   key to save the changes. If you make a mistake or change your mind before pressing the   key, simply press  to restore the previous value.In some cases, when you type a letter to select a parameter, you will see a prompt at the bottom of the screen that says Choose an Option. In these screens, press the keyboard’s   to step through the available selections. When the desired option appears, press the   key to choose that selection. In some cases, several parameters may be changed and then saved by a single keystroke. The   key can be used to cancel the action and restore the previous values.Logging Out Via Terminal Emulator or TelnetFrom the Main Menu screen, press Q to quit and terminate the session.Navigating via Web BrowserNavigating with a Web browser is straightforward with a framed “homepage.” The primary navigation menu is permanently located on the left-hand side of this page. Simply click on a desired menu item to bring it to the forefront.NOTE: To maintain security, it is best to log-out of the menu systementirely when you are done working with it. If you do not logout, the session automatically ends after 10 minutes of inac-tivity.Logging Out Via Web Browser Click on Logout in the left-hand frame of the browser window. The right-hand frame will change to a logout page. Follow the remaining instructions on this screen.ESCAPEENTERENTERESCAPESPACEBARENTERESCAPE
32 iNET Series Reference Manual 05-2806A01, Rev. HNOTE: In the menu descriptions that follow, parameter options/range,and any default values are displayed at the end of the textbetween square brackets. Note that the default setting isalways shown after a semicolon: [available settings or range;default setting]2.3 BASIC DEVICE INFORMATIONThis section contains detailed menu screens and settings that you can use to specify the behavior of the unit.2.3.1 Starting Information ScreenOnce you have logged into the Management System, you will be pre-sented with a screen that provides an overview of the transceiver and its current operating condition. It provides an array of vital information and operating conditions. Figure 2-9. Starting Information Screen•Device Mode—Current operating mode of the unit as it relates to the radio network.•Device Name—This is a user-defined parameter that will appear in the heading of all pages.(To change it, see Network Configuration Menu on Page 37.)NOTE: Do not use a colon (:) or percent (%) symbol in the devicename.•Network Name—The name of the radio network in which the unit is associated [9 to 15 characters; Not Programmed].•IP Address—Unit’s IP address [192.168.1.1]•Device Status—Condition of the unit’s association with an Access Point. At the Access Point:
05-2806A01, Rev. H iNET Series Reference Manual 33•Alarmed—A alarm event has been logged and not cleared.•Operational—Unit operating normally.At a Remote:•Scanning—The unit is looking for an Access Point beacon signal.•Exp(ecting) Sync(hronization)—The unit has found a valid beacon signal for its network.•Hop Sync—The unit has changed its frequency hopping pat-tern to match that of the Access Point.•Connected—The unit has established a radio (RF) connec-tion with the Access Point, but has not obtained cyber-secu-rity clearance to pass data.•Associated —This unit has successfully synchronized and associated with an Access Point.•Alarmed—The unit is has detected one or more alarms that have not been cleared.NOTE: If an alarm is present when this screen is displayed, an “A)”appears to the left of the Device Status field. Pressing the “A”key on your keyboard takes you directly to the “CurrentAlarms” screen.•Uptime—Elapsed time since the transceiver was powered-up.•Firmware Version—Version of firmware that is currently active in the unit.•Hardware Version— Hardware version of the transceiver’s printed circuit board.•Serial Number—Make a record of this number. It must be pro-vided to purchase Authorization Keys to upgrade unit capabili-ties. (See “Authorization Keys Menu” on Page 108.)
34 iNET Series Reference Manual 05-2806A01, Rev. H2.3.2 Main MenuThe next screen, the Main Menu, is the entryway to all user-controllable features. The transceiver’s Device Name appears at the top of this and all other screens as a reminder of the unit that is currently being controlledFigure 2-10. Main Menu•Starting Information Screen—Select this item to return to the start-up screen. (See “Starting Information Screen” on Page 32)•Network Configuration—Tools to configure the data network layer of the transceiver. (See “Network Configuration Menu” on Page 37)•Radio Configuration—Tools to configure the wireless (radio) layer of the transceiver. (See “Radio Configuration Menu” on Page 51)•Serial Gateway Configuration—Tools to configure the two serial ports. (See “Serial Data Port Configuration Menu” on Page 63)•Security Configuration—Tools to configure the security services available with the transceiver’s environment. (See “CYBER SECURITY” on Page 15)•Device Information—Top level user-specific and definable param-eters, such as unit password. (See “Device Information” on Page 35)•Performance Information—Tools to measure the radio and data layer’s performance of the radio network. (See “PERFORMANCE VERIFICATION” on Page 85)•Maintenance/Tools—Tools to use configuration files, change firmware and use Authorization Keys to change major unit capabilities. (See “Authorization Keys Menu” on Page 108)•Redundancy Configuration—For operation in protected (redun-dant) mode. The radio must be in a P21 enclosure for this oper-ation. See GE MDS publication 05-4161A01 for details, available under the Downloads tab at www.GEmds.com.
05-2806A01, Rev. H iNET Series Reference Manual 352.3.3 Configuring Basic Device ParametersDevice InformationBelow is the menu/screen that displays basic administrative data on the unit to which you are connected. It also provides access to some user- specific parameters such as device names.Figure 2-11. Device Information Menu•Model Number (Display only)•Serial Number (Display only)•Hardware Version (Display only)•Firmware Version (Display only)—Current firmware installed and being used by the transceiver.•Uptime (Display only)—Elapsed time since powering up.•Console Baud Rate—Used to set/display data communications rate (in bits-per-second) between a connected console terminal and the radio. [19200]•Device Names Menu—Fields used at user’s discretion for general administrative purposes. The Device Name field is used by the transceiver as the “Realm” name for network security and in the MS screen headings. (See Figure 2-12 on Page 36)NOTE: Do not use a colon (:) or percent (%) symbol in the devicename.•Date—Current date being used for the transceiver logs. User-set-able. (Value lost with power failure if SNTP (Simple Network Time Protocol) server not accessible.) •Time—Current time of day. User-setable. Setting: HH:MM:SS (Value lost with power failure if SNTP server not accessible.)•Date Format—Select presentation format:• Generic = dd Mmm yyyy• European = dd-mm-yyyy
36 iNET Series Reference Manual 05-2806A01, Rev. H• US = mm-dd-yyyyDevice Names MenuFigure 2-12. Device Names Menu•Device Name—Device Name, used by the transceiver as the “Realm” name for network login (web browser only) and menu headings.NOTE: Do not use a colon (:) or percent (%) symbol in the devicename.•Owner—User defined; appears on this screen only.•Contact—User defined; appears on this screen only.•Description—User defined; appears on this screen only.•Location—User defined; appears on this screen only.
05-2806A01, Rev. H iNET Series Reference Manual 372.4 CONFIGURING NETWORK PARAMETERS2.4.1 Network Configuration MenuThe Network Configuration Menu contains parameters related to the operation of TCP/IP and Ethernet protocols. There are some differences between AP and Remote type radios regarding these parameters and they are noted where appropriate.Invisible place holderFigure 2-13. Network Configuration MenuFrom Access PointInvisible place holderFigure 2-14. Network Configuration MenuFrom Remote Unit•Device Mode—Either Access Point or a variation of a Remote. [Access Point, Remote; Remote]
38 iNET Series Reference Manual 05-2806A01, Rev. HNOTE: A serial Remote can be turned into an Ethernet Bridge andvise-versa. See Change the Type of Remote on Page 108 fordetails.•Network Name—Name of the radio network that this unit belongs to. Essential for association of Remotes to the Access Point in a network. The Network Name should be at least nine characters long. [9 to 15 characters; Not Programmed]TIP: For enhanced security, consider using misspelled words, a combi-nation of letters and numbers, and a combination of upper and lower case letters. This helps protect against sophisticated hackers who may use a database of common words (for example, dictio-nary attacks) to determine the Network Name.•SNTP Server—Address of SNTP server (RFC 2030) from which the transceiver will automatically get the time-of-day startup time. Without an SNTP server, the date and time must be man-ually set. An AP will try to get the time and date from the SNTP server only if an IP address is configured. It will continue to retry every minute until it succeeds.A remote will get the time and date from the SNTP server, if an IP address is configured. Otherwise it gets it from the AP at authentication time. The transceivers use UTC (Universal Coor-dinated Time) with a configurable time offset. [0.0.0.0]•Maximum Remotes—(AP only)—Number of Remotes permitted to be associated with this Access Point. [50]•Database Timeout (AP Only)—This sets the database “age time.” See Remote Listing Menu (Access Points Only) on Page 96 to determine when a remote is declared unavailable. The timer may be set from 0 to 255 minutes and resets each time a message is received from a remote. [0–255 minutes; 5 minutes]•Database Logging (AP Only)—Determines which types of devices will be reported as “added” or “deleted” from the AP’s database (see “PERFORMANCE VERIFICATION” on Page 85). In the case of deletions, this information is triggered by the expiration of Database Timeout above. [Remote, All, Disabled; All]. (Remote only reports the remote radios. Selecting All reports endpoints and remotes).•Interface Configuration—Presents a menu for configuring the Vir-tual LAN (VLAN) and IP address of the transceiver. Detailed explanations are provided in the section titled Network Inter-face Configuration Menu on Page 39.NOTE: In GE MDS iNET radios (where VLAN is not available) thisoption is shown as IP ADDRESS CONFIGURATION. Selecting thisoption follows the description in Configuring the IP AddressWhen VLAN Status is Disabled on Page 43.
05-2806A01, Rev. H iNET Series Reference Manual 39•Ethernet Port Configuration—Presents a menu for defining the sta-tus of the Ethernet port (enabled or disabled), the Ethernet rate limit, link hardware watch (enabled/disabled), and the Ethernet link poll address. Detailed explanations of this menu are con-tained in Ethernet Port Configuration Menu on Page 45.•DHCP Server Configuration—Menu for configuration of DHCP services by the Access Point unit. DHCP provides “on-the-fly” IP address assignments to other LAN devices, including GE MDS iNET 900 units. See “DHCP Server Configuration” on Page 46 for more information. [Disabled]•SNMP Agent Configuration—Contains SNMP configuration parameters. See “SNMP Agent Configuration” on Page 47 for more information.•Rem-to-Rem bridging—This option is only available on Access Point radios. When this option is disabled communication can only happen from Remote to Access Point. This setting prevents a PC connected to one Remote radio to access a network con-nected to a different Remote within the same AP realm. [enabled, disabled; enabled]•Prioritized AP Configuration—This option is only available on Remotes. It allows the definition of a Primary AP to which a Remote radio should be connected. See “Prioritized AP Config-uration Submenu” on Page 49 for more information.•Ethernet Address (Display Only)—Hardware address of the unit’s Ethernet interface.•Wireless Address (Display Only)—Hardware address of the unit’s wireless Ethernet interface.2.4.2 Network Interface Configuration MenuBecause iNET-II and iNET radios support 802.1Q VLAN, the method for configuring the IP address of a radio may vary depending on whether the VLAN Status option is enabled or not.Invisible place holderFigure 2-15. Network Interface Configuration Menu
40 iNET Series Reference Manual 05-2806A01, Rev. H•VLAN Status—Defines if the radio handles Ethernet frames in “extended” 802.1Q mode or in “normal” mode in the Ethernet port. [enabled, disabled; disabled]•Configure Interface—Allows configuration of IP Addressing parameters. See Configuring the IP Address when VLAN Status is Enabled on Page 42, or Configuring the IP Address When VLAN Status is Disabled on Page 43.CAUTION:The VLAN Status parameter must be consistent at both theAccess Point and Remote radios in order for data to flowcorrectly. Failure to do so may result in data not being trans-ported correctly even when the radios are in an associated stateand able to communicate over-the-air. Virtual LAN in iNET-II and iNETA VLAN is essentially a limited broadcast domain, meaning that all members of a VLAN receive broadcast frames sent by members of the same VLAN but not frames sent by members of a different VLAN. Additional details can be found in the IEEE 802.1Q standard.The iNET-II and iNET support port-based VLAN at the Ethernet inter-face and over the air, according to the IEEE 802.1Q standard. When VLAN Status is enabled, the wireless port of both AP and remote radios act as a trunk port. The Ethernet port of an Access Point radio is normally configured as a trunk port. This type of port expects incoming frames to have a VLAN ID and sends outgoing frames with a VLAN structure as well.The Ethernet port of a remote radio can be configured as an access port or as a trunk port. When the Ethernet port of a Remote radio is configured as VLAN Access Port, the radio will tag incoming traffic with a VLAN ID, and will strip the tag before sending out traffic. This VLAN is known as the DATA VLAN. Additionally, a second VLAN is assigned for other traffic that is terminated at the radio, such as SNMP, TFTP, ICMP, Telnet, etc. This is known as the MANAGEMENT VLAN. Traffic directed to the integrated terminal server that handles the serial ports is assigned to the DATA VLAN.When the Ethernet port of a remote radio is configured as a VLAN trunk the radio expects all incoming Ethernet frames to be tagged, and passes through all outgoing frames as received from the wireless link, with the unchanged VLAN tag.
05-2806A01, Rev. H iNET Series Reference Manual 41NOTE: The Ethernet port in an iNET-II and iNET is 10BaseT. SomeEthernet switches allow a VLAN trunk port only on a100BaseT interface and may not be able to communicate withthe radio.Configuring for Operation with VLANWhen VLAN Status is enabled the radio uses an 802.1Q frame structure.Invisible place holderFigure 2-16. Network Interface Configuration Menu•VLAN Status—Defines whether the radio handles Ethernet frames in “extended” 802.1Q mode or in “normal” mode in the Ethernet port. Ethernet frames intended for the radio, but with a VLAN ID not configured in the radio are discarded. [enabled, disabled; disabled]NOTE:  This parameter must be consistent at both Access Point andRemote radios in order for data to flow correctly. Inconsistentconfiguration may result in data not being transportedcorrectly and the loss of over-the-air communications.NOTE: A change made to the above parameter will result in theCommit Changes option appearing on screen. This will modifythe appearance of the screen depending on the option selected.•Ethernet Port Mode—Defines if the Ethernet port acts as a trunk port or as an access port. Auto mode defines the port as an access port in an AP, or a trunk port in a Remote radio. [Auto, Trunk, Access; Auto]•Management VLAN ID—Defines the VLAN ID for traffic directed to the radio itself, other than the terminal server process. This VLAN ID is used for filtering and for tagging purposes. [1-4094; 2]
42 iNET Series Reference Manual 05-2806A01, Rev. H•Data VLAN ID—Defines the VLAN ID assigned to traffic directed to and from the Ethernet port and the terminal server process in the radio. This VLAN ID is used for filtering and for tagging purposes. [1-4094; 3]•Config Management IF—Calls up a menu to configure the IP address associated with the Management VLAN ID.•Config Data IF—Calls up a menu to configure the IP address asso-ciated with the Data VLAN ID.•Default Route IF—Defines the VLAN that contains the default gateway in the radio. [MGMT, DATA; MGMT]Configuring the IP Address when VLAN Status is EnabledThe radios require a local IP address to support remote management and serial device (terminal server) services. When the radio is configured for VLAN operation the IP address can only be set as a static IP address.Invisible place holderFigure 2-17. Management VLAN Subnet Configuration Menu•IP Address Mode—Defines the source of the IP address of this device. Only static IP addressing mode is available when VLAN Status is enabled [Static; Static]NOTE: Changes to any of the following parameters while communi-cating over the network (LAN or over-the-air) may cause aloss of communication with the unit being configured.Communication will need to be re-established using the newIP address.•Static IP Address—The IPv4 local IP address. [192.168.1.1]•Static IP Netmask—The IPv4 local subnet mask. This value is used when the radio attempts to send a locally initiated message, either from the terminal server, or management process. [255.255.0.0]•Static IP Gateway—The IPv4 address of the default gateway device, typically a router. [0.0.0.0]
05-2806A01, Rev. H iNET Series Reference Manual 43The lower three lines of the screen show the current addressing config-ured at the transceiver.NOTE: Any change made to the above parameters results in theCommit Changes option appearing on screen. This allows all IPsettings to be changed at the same time.Selecting option H from Figure 2-16 shows the screen below. Note that the IP address is different although it is the same physical unit. This is because this IP address is defined for a different VLAN.Invisible place holderFigure 2-18. Data VLAN Subnet Configuration Menu•IP Address Mode—Defines the source of the IP address of this device. Only static IP addressing mode is available when VLAN Status is enabled [Static; Static]NOTE: Changes to any of the following parameters while communi-cating over the network (LAN or over-the-air) may cause aloss of communication with the unit being configured.Communication will need to be re-established using the newIP address.•Static IP Address—The IPv4 local IP address. [192.168.1.1]•Static IP Netmask—The IPv4 local subnet mask. This value is used when the radio attempts to send a locally initiated message, either from the terminal server, or management process. [255.255.0.0]Configuring the IP Address When VLAN Status is DisabledWhen the radio is not configured for operation with VLAN, it uses one IP address to support remote management and serial device services. The IP address of a radio can be set as a static IP address or as a dynamic IP address. When static IP addressing is used, the user must manually
44 iNET Series Reference Manual 05-2806A01, Rev. Hconfigure the IP address and other parameters. When dynamic addressing is used, the radio uses a DHCP Client process to obtain an IP address from a DHCP Server, along with other parameters such as a subnet mask and a default gateway.Invisible place holderFigure 2-19. IP Address Configuration MenuCAUTION: Changes to any of the following parameters while commu-nicating over the network (LAN or over-the-air) may cause aloss of communication with the unit being configured.Communication will need to be re-established using the newIP address.•IP Address Mode—Defines the source of the IP address of thisde-vice. The IP address must be configured manually when set to Static. A DHCP server must be available for the radio to obtain a valid IP address when set to Dynamic. Only static IP address-ing mode is available when VLAN Status is enabled [Static; Static, Dynamic]•Dynamic Mode—Enabling this option forces the transceiver (AP or Remote) to obtain an IP address from any DHCP server avail-able on the LAN. Dynamic Mode is also known as DHCP Client mode. [Disabled]•Static IP Address—The IPv4 local IP address. It need not be defined if DHCP Client mode is enabled. [192.168.1.1]•Static IP Netmask—The IPv4 local subnet mask. This value is used when the radio attempts to send a locally initiated message, either from the terminal server, or management process. You don’t have to define it if DHCP Client mode is enabled. [255.255.0.0]•Static IP Gateway—The IPv4 address of the default gateway device, typically a router. [0.0.0.0]
05-2806A01, Rev. H iNET Series Reference Manual 45The lower three lines of the screen show the actual addressing at the transceiver, whether it was obtained from static configuration or from a DHCP server.NOTE: Any change made to the above parameters results in theCommit Changes option appearing on screen. This allows all IPsettings to be changed at the same time.2.4.3 Ethernet Port Configuration MenuThe transceiver allows for special control of the Ethernet interface, to allow traffic awareness and availability of the backhaul network for redundancy.NOTE: The Ethernet port in iNET and iNET-II radios support10BaseT connections only. This should not present a problembecause most hubs/switches auto-switch between 10BaseTand 100BaseT connections. Confirm that your hub/switch iscapable of auto-switching data rates.To prevent Ethernet traffic from degrading performance, placethe transceiver in a segment, or behind routers.Figure 2-20. Ethernet Port Configuration Menu•Ethernet Port Status—Allows enabling/disabling Ethernet traffic for security purposes. Setting it to Follows Link Status enables the port if there is a connection established with the AP, but disables it otherwise. [AP: Enabled, Disabled; Enabled][Remote: Always On, Follow Radio Link, Disabled; Always On]•Ethernet Rate Limit—The transceiver will send alarms (SNMP traps) when the rate reaches 50%, 75%, and 100% to help iden-tify potential problems with traffic.
46 iNET Series Reference Manual 05-2806A01, Rev. H•Ethernet Link (H/W) Watch (AP Only)—Detects the lack of an Ether-net connection to the LAN port at the electrical level (link integ-rity). The current AP will broadcast a beacon signal indicating its “NOT AVAILABLE” status so Remotes that hear it do not try to associate to it. Once the Ethernet connection is restored, this beacon signal changes to “AVAILABLE” and Remotes are allowed to join in. [Disabled]•Ethernet Link Poll Address (AP Only)—When an IP address is pro-vided, the Access Point pings the remote IP device every 60 sec-onds to test the integrity of the backhaul link. If this link is not available, the AP will advertise its “NOT AVAILABLE” status in the beacon signal so Remotes do not try to associate to it. Once the IP address is reachable, this beacon signal changes to “AVAILABLE” and Remotes are allowed to join in. 0.0.0.0 dis-ables this function. Any other valid IP address enables it. [0.0.0.0]2.4.4 DHCP Server ConfigurationA transceiver can provide automatic IP address assignments to other IP devices in the network by providing DHCP (Dynamic Host Configura-tion Protocol) services. This service eliminates setting individual device IP address on Remotes in the network, but it still requires thoughtful planning of the IP address range. One drawback to network-wide auto-matic IP address assignments is that SNMP services may become inac-cessible as they are dependent on fixed IP addresses.The network can be comprised of radios with the DHCP-provided IP address enabled or with DHCP services disabled. In this way, you can accommodate locations for which a fixed IP address if desired.Figure 2-21. DHCP Server Configuration Menu
05-2806A01, Rev. H iNET Series Reference Manual 47NOTE: There should be only one DHCP server active in a network(GE MDS iNET 900 or other DHCP server). If more than oneDHCP server exists, network devices may randomly get theirIP address from different servers every time they request one.NOTE: Combining DHCP and RADIUS device authentication mayresult in a non-working radio module if the DHCP server islocated at a remote radio. The DHCP server should be placedat the AP location, if possible.•Server Status—Enable/Disable responding to DHCP requests to assign an IP address. [Disabled/Enabled; Disabled]•DHCP Netmask—IP netmask to be assigned along with the IP address in response to a DHCP request. [0.0.0.0]•Starting Address—Lowest IP address of the range of addresses to be provided by this device. [0.0.0.0]•Ending Address—Highest IP address in the range of addresses to be provided by this device. A maximum of 256 addresses is allowed in this range. [0.0.0.0]•DNS Address—Domain Name Server address to be provided by this service.•WINS Address—Windows Internet Naming Service server address to be provided by this service.•Restart DHCP Server—Selecting this option forces the transceiver to start servicing DHCP requests using the Starting Address. Payload data will not be interrupted but may experience some delays as new addresses are distributed.2.4.5 SNMP Agent ConfigurationThe transceiver contains over 100 custom SNMP-manageable objects as well as the IETF standard RFC1213 for protocol statistics, also known as MIB II. Off-the-shelf SNMP managers such as Castle Rock Com-puting SNMPc™ and Hewlett Packard HP OpenView™ may also be used to access the transceiver’s SNMP Agent’s MIB. The transceiver’s SNMP agent supports SNMPv3.The objects are broken up into several MIB files. There are textual con-ventions, common files and specific files. This allows the flexibility to change areas of the MIB and not affect other existing installations or customers.•msdreg.mib—GE MDS sub-tree registrations•MDS_comm.mib—GE MDS Common MIB definitions for objects and events which are common to the entire product fam-ily•inet_reg.mib—GE MDS sub-tree registrations•inettrv1.mib—SNMPv1 enterprise-specific traps•inettrv2.mib—SNMPv2 enterprise-specific traps
48 iNET Series Reference Manual 05-2806A01, Rev. H•inet_comm.mib— MIB definitions for objects and events which are common to the entire iNET Series•inet_ap.mib—MIB definitions for objects and events for an Access Point transceiver•inet_sta.mib—Definitions for objects and events for a Remote radio•inet_sec.mib—For security management of the radio system. SNMPv3 allows read/write operation. SNMPv1/2 allows only for read-only access.•inet2.mib—Additional objects specific to iNET-II.NOTE: SNMP management requires that the proper IP address,network and gateway addresses are configured in each trans-ceiver of the associated network. In addition, some management systems may require the MIBfiles to be compiled in the order shown above.Invisible place holderFigure 2-22. SNMP Server Configuration MenuFrom Access PointThis menu provides configuration and control of vital SNMP functions. •Read Community String—SNMP community name with SNMPv1/SNMPv2c read access. This string can be up to 30 alpha-numeric characters.•Write Community String—SNMP community name with SNMPv1/SNMPv2c write access. This string can be up to 30 alpha-numeric characters.•Trap Community String—SNMP community name with SNMPv1/SNMPv2c trap access. This string can be up to 30 alpha-numeric characters.
05-2806A01, Rev. H iNET Series Reference Manual 49•V3 Authentication Password—Authentication password stored in flash memory. This is used when the Agent is managing pass-words locally (or initially for all cases on reboot). This is the SNMPv3 password used for Authentication (currently, only MD5 is supported). This string can be up to 30 alpha-numeric characters.¥V3 Privacy PasswordPrivacy password stored in flash memory. Used when the SNMP Agent is managing passwords locally (or initially for all cases on reboot). This is the SNMPv3 password used for privacy (DES encryption). This string can be between 8 and 30 alpha-numeric characters.•SNMP Mode—This specifies the mode of operation of the radio’s SNMP Agent. The choices are: disabled, v1_only, v2_only, v3_only. v1-v2, and v1-v2-v3. If the mode is disabled, the Agent does not respond to any SNMP traffic. If the mode is v1_only, v2_only, or v3_only, the Agent responds only to that version of SNMP traffic. If the mode is v1-v2, or v1-v2-v3, the Agent responds to the specified version of SNMP traffic. [v1-v2-v3]•Trap Version—This specifies what version of SNMP will be used to encode the outgoing traps. The choices are v1_traps, v2_traps, and v3_traps. When v3_traps are selected, v2-style traps are sent, but with a v3 header. [v1 Traps, v2 Traps, v3 Traps]•Auth Traps Status—Indicates whether or not traps will be gener-ated for login events to the transceiver. [Disabled/Enabled; Dis-abled]•SNMP V3 Passwords—Determines whether v3 passwords are managed locally or via an SNMP Manager. The different behav-iors of the Agent depending on the mode selected, are described in SNMP Mode above.•Trap Manager #1–#4— Table of up to 4 locations on the network that traps are sent to. [Any standard IP address]NOTE: The number in the upper right-hand corner of the screen is theSNMP Agent’s SNMPv3 Engine ID. Some SNMP Managersmay need to know this ID in order interface with the trans-ceiver’s SNMP Agent. The ID only appears on the screenwhen SNMP Mode is either v1-v2-v3 or v3_only.2.4.6 Prioritized AP Configuration SubmenuThe Prioritized AP feature (Figure 2-23) allows the definition of a Pri-mary AP to which a Remote radio should be connected.
50 iNET Series Reference Manual 05-2806A01, Rev. HInvisible place holderFigure 2-23. Prioritized AP Configuration Submenu•Prioritized AP—Shows status of the prioritization option.[enabled, disabled; disabled]•Scan Time—Number of seconds that a Remote waits to receive beacons from an AP included in the Approved AP List. After this time, the list will be expanded to include the next entry and the cycle will be repeated until association is achieved.•Connection Time—Amount of time that a Remote waits before breaking the connection and looking for an AP. This event hap-pens only when the current AP is not the first entry in the Approved AP List, which means that the remote is not con-nected to the primary AP.•Approved Access Points List—Displays the list of Approved AP used for local authentication purposes. This table is not the same as the Priority Table discussed here, and is only included as an aid to facilitate configuration.•Import from Approved List—Copies the entries configured in the Approved AP List to this priority table.•1-10—Priority Table of Access Points. This table should include the Wireless MAC Address of the desired Access Point units.When association to an AP is terminated for any reason, the Remote enters Scanning mode. During this time it listens for beacons from an AP that matches the network name. If the Prioritized AP option is enabled, then the Wireless MAC Address of the AP must be part of the list at the remote. The initial list includes only the first entry of the table. If no beacon is received that matches the requirement and the Scan Time is exceeded, then the list is expanded to include the first two entries.When a beacon matches the requirements, then the association process continues. It may be that the Remote associates to an AP that is not the first entry in the table. In this case the Remote will wait for Connection Time before breaking the connection and starting the process all over
05-2806A01, Rev. H iNET Series Reference Manual 51again. This process will be repeated until the Remote associates to the first entry in the list (the Primary Access Point).2.5 RADIO CONFIGURATIONThere are two primary data layers in the transceiver network—radio and data. Since the data layer is dependent on the radio layer working prop-erly, configuration of the radio items should be reviewed and set before proceeding. This section explains the Radio Configuration Menu, (Figure 2-24 for AP, Figure 2-25 for Remote).2.5.1 Radio Configuration MenuFigure 2-24. Radio Configuration Menu(From Access Point Unit)
52 iNET Series Reference Manual 05-2806A01, Rev. HFigure 2-25. Radio Configuration Menu(From Remote Unit)•RF Output Power—Sets/displays RF power output level. Dis-played in dBm. Setting should reflect local regulatory limita-tions and losses in antenna transmission line. (See “How Much Output Power Can be Used?” on Page 135 for information on how to calculate this value.)[20–30; 20]•Data Rate—Shows the over-the-air data rate setting for the Remote radio. Remotes can operate at one of two data rates when communicating with an AP: 1024 kbps (1 Mbps) or 512 kbps for iNET-II and 256 kbps or 512 kbps for iNET. The fast-est data rate is possible with strong RF signal levels, typically stronger than –77 dBm RSSI including a 15 dB fade margin.When the data rate is set to AUTO, the remote radio is able to change speeds based on the signal quality criteria set in the Auto Data Rate submenu described later in this section (see Page 54).[iNET: 256, 512, AUTO; AUTO] [iNET-II: 512, 1024, AUTO; AUTO] •Compression (AP Only)—Enabling this option uses LZO com-pression algorithm for over-the-air data. Varying levels of data reduction are achieved depending on the nature of the informa-tion. Text files are typically the most compressible, whereas binary files are the least compressible. On average, a 30% increase in throughput can be achieved with compression enabled.•Dwell Time—Duration (in milliseconds) of one hop on a particu-lar frequency in the hopping pattern. (This field is only change-able on an Access Point. Remotes get their value from AP upon association.) [iNET: 16.4, 32.8, 65.5, 131.1, 262.1; 32.8][iNET-II: 8.2, 16.4, 32.8, 65.5, 131.1; 32.8]
05-2806A01, Rev. H iNET Series Reference Manual 53TIP: If a packet is being transmitted and the dwell time expires, the packet will be completed before hopping to the next frequency. •Beacon Period—Amount of time between Beacon transmissions (in msec).Available Intervals: Normal (104 ms), Fast (52 ms), Faster (26 ms), Slow (508 ms), Moderate (208 ms). These values provide rel-atively quick association times where Fast is very fast (≈ 5 sec) and the other end, the largest recommended value, the 508 ms period is slow (≈ 60 sec). [Normal, Fast, Faster, Slow, Moderate; Nor-mal]TIP: Increasing the Beacon Period will provide a small improvement in network data throughput. Shortening it decreases the time needed for Remotes to associate with the AP. A short beacon period is usually only a benefit when there are mobile Remotes in the network.•Hop Pattern Seed—A user-selectable value to be added to the hop pattern formula. This is done in the unlikely event that identical hop patterns are used with two collocated or nearby networks. Changing the seed value will minimize the potential for RF-sig-nal collisions in these situations. (This field is only changeable on an Access Point. Remotes read the AP’s value upon associa-tion.) [0 to 255; 1]•Mobility Configuration—This selection brings up a submenu where parameters related to mobile operation may be set. For details, See “Mobility Configuration Menu” on Page 58.•Fragment Threshold—Before transmitting over the air, if a packet exceeds this number of bytes, the transceiver sends the packet in multiple fragments that are reassembled before being delivered over the Ethernet interface at the receiving end. Only even num-bers are acceptable entries for this parameter. Over-the-air data fragmentation is not supported on AP units. (See “PERFORMANCE NOTES” on Page 144 for additional information.) [256–1600 bytes; 1600]TIP: In an interference-free environment this value should be large to maximize throughput. If interference exists then the value should be set to smaller values. The smaller the packet the less chance of it being interfered with at the cost of slightly reduced throughput.•RTS Threshold—Number of bytes for the over-the-air RTS/CTS handshake boundary. (See “PERFORMANCE NOTES” on Page 144.) [0 to 1600 bytes; 500]NOTE: While the transceiver accepts RTS Threshold settings below100, the lowest functioning value is 100.
54 iNET Series Reference Manual 05-2806A01, Rev. HTIP: Lower the RTS Threshold as the number of Remotes or overall over-the-air traffic increases. Using RTS/CTS is a trade-off, giving up some throughput in order to prevent collisions in a busy over-the-air network.The RTS Threshold should be enabled and set with a value smaller than the Fragmentation Threshold described above. RTS forces the Remotes to request permission from the AP before sending a packet. The AP sends a CTS control packet to grant permission to one Remote. All other Remotes wait for the specified amount of time before transmitting.•RSSI Threshold (for alarm)—Level (dBm) below which the received signal strength is deemed to have degraded, and a crit-ical event (alarm) is generated and logged. Under these condi-tions, the PWR lamp flashes, and an SNMP trap is sent to the configured SNMP manager. [0 to -120; -90]•SNR Threshold (for alarm)—Value (dB) below which the sig-nal-to-noise ratio is deemed to have degraded and a critical event is generated and logged. Under these conditions, the PWR lamp flashes, and an SNMP trap is sent to the configured SNMP manager. [0 to 40; Not Programmed]•Channel Config (Only applies to iNET-II)—Brings up the submenu discussed in Channel Config Menu on Page 54.•RF Hopping Format (Only applies to iNET)—This option must be specified when the order is placed and cannot be modified in the field by the user. Operation must be compliant with coun-try-specific restrictions. The available formats are:•ISM: 902–928 MHz band•GSM: 915–928 MHz band•SPLIT: 902-907.5 and 915-928 MHz bands•CHANNELS: 902–928 MHz, individual channels selectable within this range•Skip Zones (Only applies to iNET. Editable at AP Only.)—This selection brings up a submenu discussed in Skip Zones Menu on Page 55.•Auto Data Rate Configuration—This selection brings up a submenu as shown in Figure 2-28. For the settings in this submenu to have any effect, the Data Rate menu item (Page 52) must be set to AUTO. 2.5.2 Channel Config MenuThe Channel Configuration menu displays the utilization of channels in the 902–928 MHz range. This selection is available only on iNET-II or specially provisioned iNET units. The radio hops only on the channels selected in this menu.
05-2806A01, Rev. H iNET Series Reference Manual 55Invisible place holderFigure 2-26. Channel Config SubmenuKey to channel indicators:n (no) = Radio channel is not usedy (yes) = Radio channel is usedNA (not available) = Radio channel is not available•Clear All—This command clears all entries in the Channel Config Menu, resetting the available channels to “no usage.” Channels that are not available for use will appear with a notation of or NA. These channels are not available because of pre-existing conditions, and are not user-configurable.•Enter Channels—This allows selection of the channels used for frequency hopping operation. The selection of particular channels will result in an indication of y. Be aware that these channels do not become active until the Commit Changes selection is invoked.•Commit Changes—This re-boots the radio and loads the active channels into the frequency list for frequency hopping oper-ation.2.5.3 Skip Zones Menu•Skip Zones (Does not apply to iNET-II. Editable at AP Only.)—This selection brings up a submenu (Figure 2-27) that displays the current utilization of zones. Each zone consists of eight RF channels. In some instances there may be a part of the spectrum used by another system, that results in “continuous” or “persis-tent” interference to your system. To alleviate this form of inter-ference, the transceiver may be programmed to “block out” affected portions of the spectrum using the Skip Zones Menu.
56 iNET Series Reference Manual 05-2806A01, Rev. HFigure 2-27. Skip Zone Options Submenu—GE MDS iNET Only(“Commit changes” displayed only on Access Point radios)Figure 2-27 displays the utilization of 10 zones, each having eight RF operating frequencies. Zones can be toggled between Active and Skipped at Access Point units by first keying in the let-ter of the zone to be changed, and then pressing the spacebar to toggle between the two options for each zone. Select the Commit Changes menu item to implement changes. These changes will be forwarded to all units in the network through the Access Point’s beacon signal.With an iNET radio (non-iNET-II), a maximum of three zones can be skipped and still be compliant with FCC regulations.2.5.4 Auto Data Rate Configuration MenuThe Auto Data Rate Configuration submenu is typically for use in envi-ronments where signal quality is variable, and you wish to maintain the highest possible over-the-air data rate as conditions change.
05-2806A01, Rev. H iNET Series Reference Manual 57Invisible place holderFigure 2-28. Auto Data Rate Submenu•ADR RSSI Threshold—A specified received signal strength value, which, if exceeded by the range of the RSSI Delta set-ting, causes a data rate change in the transceiver. [-50 to -100; -87 dBm]•ADR RSSI Delta—A user-specified difference from the RSSI Threshold figure which, if exceeded, causes a data rate change in the transceiver. [0-10; 5]•ADR SNR Threshold—A user-specified signal-to-noise ratio, which, if exceeded by the range of the SNR Delta setting, causes a data rate change in the transceiver. [10-30; 26]•ADR SNR Delta—A user-specified difference from the SNR Threshold figure which, if exceeded, causes a data rate change in the transceiver. [0-10; 2]NOTE: In the description below, “high speed” refers to 512 kbps forthe iNET radio and 1 Mbps for the iNET-II radio.“Standard speed” refers to 256 kbps for the iNET radio and512 kbps for the iNET-II.Using the example of Figure 2-28, assume the current RSSI is -87 dBm. An RSSI reduction of more than 5 dBm (more negative RSSI number) would cause a data rate change from high speed to standard speed. Once the data speed has changed to standard speed, an RSSI increase to the level of -82 dBm would be required for the radio to switch back to high speed. This provides an operational “window” or hysteresis range over which the data speed stays constant despite minor changes in signal strength.
58 iNET Series Reference Manual 05-2806A01, Rev. HThe SNR (signal-to-noise ratio) threshold and delta operate in the same manner described above, with the exception that the units are expressed in relative dB instead of dBm. In the example of Figure 2-28, a drop of 2 dB from a level of 26 dB would result in a data rate change from high speed to standard speed. For the radio to return to high speed, the SNR would need to increase to 28 dB. (See Glossary for definition of SNR.)RSSI or SNR figures alone mean little when determining signal quality. Both parameters must be considered to get a true understanding of signal quality. For example, a strong, but noisy signal would likely be less useful than a weak signal with low noise levels. Proper use of the threshold and delta settings will result in smoother, more reliable perfor-mance from your wireless link.Figure 2-28 shows the default values for RSSI and SNR parameters but these may be changed to optimize performance in your environment. In properly designed systems, experience has shown that RSSI levels between -50 dBm and -90 dBm provide reliable operation, provided the signal-to-noise ratio is 17 dB or above. Tailoring the thresholds with these baseline values in mind, can provide improved performance in your system.NOTE: The RSSI is an average of the last 20 RSSI samples. The RSSIvalue is reset every time the radio returns to scanning mode.2.5.5 Mobility Configuration MenuA mobile environment requires special considerations that are not a factor in fixed installations. Use the following menu to set Remote radios for mobile operation.Invisible place holderFigure 2-29. Mobility Screen Showing Blacklist Timer Value
05-2806A01, Rev. H iNET Series Reference Manual 59•Mobility Mode—Selects whether or not mobility-specific param-eters are active. [enabled, disabled; disabled]•Blacklist Timer—Sets/displays the number of seconds an AP stays on the blacklist after association is lost. [10-120; 10]•Settling Timer—Sets/displays the number of seconds the radio waits before evaluating the signal quality of a newly acquired AP. [5-120; 10]After association is lost with an AP, and scanning for an alternate AP is started, the former AP is placed on a “blacklist” to avoid linking imme-diately back to the same AP. If no alternate AP is found, a link will be attempted with the same AP as before.An Access Point is added to the blacklist when the Remote detects that the RSSI has dropped below the RSSI Threshold set in the Radio Config-uration menu and should try to find an alternate AP to connect to.An Access Point is removed from the blacklist table when it has been in the table longer than the time set by the Blacklist Timer. Additional Considerations for Mobile OperationThe following key points should be considered for all mobile installa-tions:• Use middleware—The use of middleware in the mobile laptops is highly recommended for better operation of a mobile data system. GE MDS provides middleware from one of the vendors in this mar-ket. Contact your GE MDS representative for details.• Plan your network coverage—Deploy Access Points so that they provide overlapping coverage to each other. Access Points must use the same network name to enable roaming• Set the Remote radios to the lower speed (512 kbps for iNET-II, 256 kbps for iNET) to optimize coverage• Set the RSSI Threshold to -85 dBm—This level is typically used for mobile systems with good performance. Make sure there is overlap-ping coverage of more than one AP to provide a good user experi-ence and continuous coverage.At Every Mobile (Remote) Radio•Fragmentation Threshold [256]—Set to a small value. This param-eter defines the size of the message packets transmitted over the wireless media. These fragments are reconstructed into the orig-inal packet before delivery to the external device at the remote end of the link. In a mobile environment with rapidly changing conditions, setting this value to a minimum value improves the probability of packets being sent complete on the first try.
60 iNET Series Reference Manual 05-2806A01, Rev. HAt Every AP RadioParameter settings that should be reviewed for AP radios providing ser-vice to mobile remotes:•Compression [disabled]—Disable radio compression. Data com-pression is best performed by the middleware running on the mobile laptop PC. Gains in efficiency are made because middle-ware compresses data at a higher stack level, and it aggregates multiple data frames and streams into a single packet. Compres-sion at the radio level, although highly efficient, works at the individual packet level.•Dwell Time [Set to the minimum value]—This setting controls the amount of time that the unit spends on each frequency between hops. Although overall throughput appears to decrease by this setting the effects of multipath fading are minimized through frequency diversity.•Beacon Period [Set to the fastest value]—This parameter defines the interval at which the Access Point transmits a synchroniza-tion beacon to all remotes. A faster setting minimizes resyn-chronization times when remote radios roam between access points or in highly interrupted coverage areas (dense buildings, for example).•RTS Threshold [0 -1600 bytes]—Enable RTS flow at a small value. This setting is a wireless equivalent to RTS/CTS flow control in a wired communications circuit. This mechanism prevents packet collisions caused by the “Hidden Node” scenario, in which remotes can’t hear each other before transmitting. When this value is set below 100 or above 1500, it is effectively dis-abled.2.6 CONFIGURING THE SERIAL PORTS2.6.1 OverviewThe transceiver includes an embedded serial device server that provides transparent encapsulation over IP. In this capacity, it acts as a gateway between serial and IP remote devices. Two common scenarios are PC applications using IP to talk to remote devices, and serial PC applica-tions talking to remote serial devices over an IP network.Essentially the same data services are available for both serial ports: COM1 and COM2. Note that the transceiver’s COM1 port is DCE and COM2 is DTE. Therefore, if the RTU to be connected is also DTE, then a null-modem cable will need to be used when connecting to COM2.
05-2806A01, Rev. H iNET Series Reference Manual 61NOTE: In the discussion that follows, COM1 and COM2 will be treatedalike unless noted.Com1 Port–Dual Purpose CapabilityThe COM1 port is used as a local console connection point and to pass serial data with an external device. Setting the COM1 port status to Enable prevents access to the Management System (MS) through this port. However, the MS can still be accessed via the LAN port using Telnet or a web browser.To restore the COM1 port to support Management System services, connect a terminal to the port, select the proper baud rate (19,200 is default), and enter an escape sequence (+++) to reset it to the console mode.TCP vs. UDPBoth types of IP services are used by the transceiver embedded serial device server—TCP and UDP. TCP provides a connection-oriented link with end-to-end acknowledgment of data, but with some added over-head. UDP provides a connectionless best-effort delivery service with no acknowledgment.Most polled protocols will be best served by UDP service as the protocol itself has built-in error recovery mechanisms. UDP provides the needed multidrop operation by means of multicast addressing.On the other hand, TCP services are best suited for applications that do not have a recovery mechanism (error-correction) and must have the guaranteed delivery that TCP provides despite the extra overhead. The IP-to-Serial example shows how to do this. (See “IP-to-Serial Applica-tion Example” on Page 71.)Serial EncapsulationTransparent encapsulation, or IP tunneling, provides a mechanism to encapsulate serial data into an IP envelope. Basically, all the bytes received through the serial port are put into the data portion of a TCP or UDP packet (TCP or UDP are user configurable options). In the same manner, all data bytes received in a TCP or UDP packet are output through the serial port.When data is received by the radio through the serial port it is buffered until the packet is received completely. There are two events that signal an end-of-packet to the radio: a period of time since the last byte was received, or a number of bytes that exceed the buffer size. Both of these triggers are user configurable.
62 iNET Series Reference Manual 05-2806A01, Rev. HOne radio can perform serial data encapsulation (IP-to-Serial) and talk to a PC. Two radios (or one radio and a terminal server) can be used together to provide a serial-to-serial channel.TCP Client vs. TCP ServerA TCP session has a server side and a client side. You can configure the transceiver to act as a server, a client, or both. TCP servers listen and wait for requests from remote TCP clients to establish a session. A TCP client is a program running on a device other than the TCP server. Alternately, TCP clients actively attempt to estab-lish a connection with a TCP server. In the case of the transceiver, this happens whenever data is received on the serial port.The transceiver operates in either client or server mode, depending on which event occurs first, either receiving data on the serial port, or receiving a request to open a TCP connection from a remote client.The transceiver keeps a TCP session open until internal timers that mon-itor traffic expire. Once a TCP session is closed, it must be opened again before traffic can flow.UDP MulticastIP provides a mechanism to do a limited broadcast to a specific group of devices. This is known as “multicast addressing.” Many IP routers, hubs and switches support this functionality. Multicast addressing requires the use of a specific branch of IP addresses set apart by the Internet Assigned Numbers Authority (IANA) for this purpose.UDP multicast is generally used to transport polling protocols typically used in SCADA applications where multiple remote devices will receive and process the same poll message.As part of the Multicast implementation, the radio sends IGMP mem-bership reports and IGMP queries, and responds to membership queries. It defaults to V2 membership reports, but responds to both V1 and V2 queries. You must configure the multicasted serial port as the target for the mul-ticast data (for example, multipoint-to-multipoint mode, or point-to-multipoint mode where the inbound data is multicast). This restriction is because a host that only sends data to a multicast address (for example, point-to-multipoint mode where the iNET acts as a point) will not join the group to receive multicast data because the host’s inbound data is directed unicast data.
05-2806A01, Rev. H iNET Series Reference Manual 63The serial-to-serial example which follows shows how to provide mul-ticast services. (See “Point-to-Multipoint IP-to-Serial Application Example” on Page 72.)PPPExternal devices can connect to the transceiver using PPP (Point-to-Point Protocol). The transceiver works as a server and assigns an IP address to the device that connects through this interface.To gain access to the transceiver from a PC even if the network is down, a modem may be connected to one of the transceiver’s COM ports that has been configured with PPP.Data BufferingData buffering is always active regardless of the selected mode. When Seamless mode is selected, a buffer size of 256 bytes is used. When custom mode is selected, the size options are: 16. 32, 64, 128, and 256 bytes. The Inter-Frame Delay is settable in either Seamless or Custom modes.Implementing Configuration ChangesThere are several configuration parameters for the Serial Gateway found under the Serial Configuration Menu of the Management System. After making changes to the configuration, you must use the menu’s “Commit Changes” to assert the changes.If you are connecting EIA-232 serial devices to the transceiver, review these parameters carefully.Serial Configuration WizardThe Serial Configuration Wizard available through the Serial Gateway Configuration Menu is recommended for configuration of serial ports. The wizard uses a step-by-step process, will eliminate possible conflicting settings, and streamline complex configurations.The wizard can be bypassed by selecting option B) View Current Settings and adjusting the individual settings of the appropriate parameter2.6.2 Serial Data Port Configuration MenuThe first two menu items present the identical parameter fields for each port with one exception—Flow Control. This is available only on COM2.
64 iNET Series Reference Manual 05-2806A01, Rev. H Figure 2-30. Serial Configuration Wizard•Begin Wizard—Tool for configuration of serial ports using a step-by-step process.•View Current Settings—Displays all settable options. Depend-ing on the selected IP protocol.2.6.3 Configuring for UDP ModeInvisible place holderFigure 2-31. UDP Point-to-Multipoint MenuUse UDP point-to-multipoint to send a copy of the same packet to mul-tiple destinations, such as in a polling protocol.•Status—Enable/Disable the serial data port.
05-2806A01, Rev. H iNET Series Reference Manual 65•IP Protocol—Point to Multipoint [TCP, UDP PPP; TCP]. This is the type of IP port that will be offered by the transceiver’s serial device server.•Multicast IP Address (used instead of Local IP Address when using UDP Point-to-Multipoint.)— Must be configured with a valid Class D IP address (224.0.0.0–239.255.255.255). IP packets received with a matching destination address will be processed by this unit [Any legal IP address; 0.0.0.0].•Multicast IP Port (used instead of Local IP Port when using UDP Point-to-Multipoint.)—This port number must match the number used by the application connecting to local TCP or UDP socket. [1-64,000; COM1: 30010, COM2: 30011]•Local IP Port—Receive IP data from this source and pass it through to the connected serial device. The port number must be used by the application connecting to local TCP or UDP socket. [Any valid IP port; COM1: 30010, COM2: 30011]•Time to Live (TTL)—An IP parameter defining the number of hops that the packet is allowed to traverse. Every router in the path will decrement this counter by one.•Packet Redundancy Mode— For proper operation, all radios’ Serial Packet Redundancy mode must match (Single Packet mode vs. Packet Repeat mode). This is because a transceiver, when in Packet Repeat mode, sends 12 extra characters (sequence numbers, etc.) to control the delivery of the repeated data. Misconfigurations can result in undesired operation.•Data Baud Rate—Data rate (payload) for the COM port in bits-per-second. [1,200–115,200; 19200] •Configuration—Formatting of data bytes, representing data bits, parity and stop bits. [7N1, 7E1, 7O1, 8N1, 8E1, 8O1, 8N1, 7N2, 7E2, 7O2, 8N2, 8E2, 8O2; 8N1]•Flow Control [Com2 Only]—RTS/CTS handshaking between the transceiver and the connected device. [Enable, Disable; Dis-abled]•Serial Mode—When seamless mode is selected data bytes entering the serial data port are sent over the radio link with-out delay, but the receiving end will buffer the data until enough bytes have arrived to cover worst-case gaps in trans-mission. The delay introduced by data buffering may range from 22 to 44 ms, but the radio will not create any gaps in the output data stream. This permits operation with protocols such as MODBUS™ that do not allow gaps in their data transmission. [Seamless, Custom; Seamless]•Seamless Inter-Frame Delay— Amount of time (in number of characters) that signal the end of a message (inter-character time-out). UDP packet sizes are delimited and sent out based on the Seamless Inter-Frame Delay only when receiving data through the serial port. MODBUS defines a “3.5-character” setting. [1–65,535; 4]
66 iNET Series Reference Manual 05-2806A01, Rev. HTIP: To convert this delay into milliseconds, multiply the number of characters configured here by 10 (there are usu-ally 10 bits in each byte) and divide the result by the data rate of the serial port (in kbps).•Custom Data Buffer Size (Custom Packet Mode only)—Maxi-mum amount of characters, that the Remote end will buffer locally before starting to transmit data through the serial port. [16, 32, 64, 128, 256; 32]•Commit Changes and Exit Wizard—Save and execute changes made on this screen (Shown only after changes have been entered.) Invisible place holderFigure 2-32. UDP Point-to-Point MenuUse UDP point-to-point configuration to send information to a single device.•Status—Enable/Disable the serial data port. •IP Protocol—UDP Point-to-Point. This is the type of IP port that will be offered by the transceiver’s serial device server. [TCP, UDP, PPP; TCP]•Remote IP Address—Data received through the serial port is sent to this IP address. To reach multiple Remotes in the net-work, use UDP Point-to-Multipoint. [Any legal IP address; 0.0.0.0]•Remote IP Port—The destination IP port for data packets received through the serial port on the transceiver. [1–64,000; COM1: 30010, COM2: 30011]•Local IP Port—Port number where data is received and passed through to the serial port. This port number must be used by the application connecting to this transceiver. [1–64,000; COM1: 30010, COM2: 30011]
05-2806A01, Rev. H iNET Series Reference Manual 67•Packet Redundancy Mode— For proper operation, all radios’ Serial Packet Redundancy mode must match (Single Packet mode vs. Packet Repeat mode). This is because a transceiver, when in Packet Repeat mode, sends 12 extra characters (sequence numbers, etc.) to control the delivery of the repeated data. Misconfigurations can result in undesired operation.•Data Baud Rate—Data rate (payload) for the COM port in bits-per-second. [1,200–115,200; 19200] •Configuration—Formatting of data bytes. Data bits, parity and stop bits [7N1, 7E1, 7O1, 8N1, 8E1, 8O1, 8N1, 7N2, 7E2, 7O2, 8N2, 8E2, 8O2; 8N1].•Flow Control (COM2 only)—RTS/CTS handshaking between the transceiver and the connected device.[Enable, Disable; Disabled]•Serial Mode— When seamless mode is selected, data bytes will be sent over the air as quickly as possible, but the receiver will buffer the data until enough bytes have arrived to cover worst case gaps in transmission. The delay intro-duced by data buffering may range from 22 to 44 ms, but the radio will not create any gaps in the output data stream. This mode of operation is required for protocols such as MOD-BUS™ that do not allow gaps in their data transmission. [Seamless, Custom; Seamless]•Seamless Inter-Frame Delay— Number of characters that repre-sent the end of a message (inter-character time-out). MOD-BUS defines a “3.5-character” parameter. [1–65,535; 4]•Custom Data Buffer Size (Custom Packet Mode only)—Maxi-mum amount of characters, that the Remote end will buffer locally before starting to transmit data through the serial port. [16, 32, 64, 128, 256; 32]•Commit Changes and Exit Wizard—Save and execute changes made on this screen (Shown only after changes have been entered.)
68 iNET Series Reference Manual 05-2806A01, Rev. H2.6.4 Configuring for TCP ModeInvisible place holderFigure 2-33. TCP Client Menu (Remote)•Status—Enable/Disable the serial data port. •IP Protocol—TCP Client. This is the type of IP port that will be offered by the transceiver’s serial device server. [TCP, UDP, PPP; TCP]•Primary Host Address—The IP address to be used as a destina-tion for data received through the serial port.[Any legal IP address; 0.0.0.0]•Primary IP Port—The destination IP port for data packets received through the serial port on the transceiver.[Any valid IP port; COM1: 30010, COM2: 30011]•Secondary Host Address—The IP address to be used as a desti-nation for data received through the serial port in case the pri-mary host address is not available.[Any legal IP address; 0.0.0.0]•Secondary IP Port—The destination IP port for data packets received through the serial port on the transceiver used along with the secondary host address above.[Any valid IP port; COM1: 30010, COM2: 30011]•Client Inactivity Timeout (sec)—Amount of time (in seconds) that the transceiver will wait for data before terminating the TCP session. [0–600; 600]•Data Baud Rate—Data rate (payload) for the COM port in bits-per-second. [1,200–115,200; 19200] •Configuration—Interface signaling parameters. Data bits, par-ity and stop bits [7N1, 7E1, 7O1, 8N1, 8E1, 8O1, 8N1, 7N2, 7E2, 7O2, 8N2, 8E2, 8O2; 8N1].•Flow Control [Com2 Only]—RTS/CTS handshaking between the transceiver and the connected device.[Enable, Disable; Disabled]
05-2806A01, Rev. H iNET Series Reference Manual 69•Serial Mode— If data buffering is Enabled, the radio will oper-ate in seamless mode. Data bytes will be sent over the air as quickly as possible, but the receiver will buffer the data until enough bytes have arrived to cover worst case gaps in trans-mission. The delay introduced by data buffering may range from 22 to 44 ms, but the radio will not create any gaps in the output data stream. This mode of operation is required for protocols such as MODBUS™ and some variants which do not allow gaps in their data transmission.[Seamless, Custom; Seamless]•Seamless Inter-Frame Delay— Number of characters that repre-sent the end of a message (inter-character time-out). MOD-BUS defines a “3.5-character” parameter.[1–65,535; 4]•Custom Data Buffer Size (Custom Packet Mode only)—Maxi-mum amount of characters, that the Remote end will buffer locally before starting to transmit data through the serial port. [16, 32, 64, 128, 256; 32]•Commit Changes and Exit Wizard—Save and execute changes made on this screen (Shown only after changes have been entered.) Invisible place holderFigure 2-34. TCP Server Menu (AP)•Status—Enable/Disable the serial data port. •IP Protocol—TCP Server. This is the type of IP port that will be offered by the transceiver’s serial device server. [TCP, UDP, PPP; TCP]•Local Listening IP Port—Receive IP data from this source and pass it through to the connected serial device. The port num-ber must be used by the application connecting to local TCP or UDP socket.[Any valid IP port; COM1: 30010, COM2: 30011]
70 iNET Series Reference Manual 05-2806A01, Rev. H•Data Baud Rate—Data rate (payload) for the COM port in bits-per-second. [1,200–115,200; 19200] •Configuration—Interface signaling parameters. Data bits, par-ity and stop bits [7N1, 7E1, 7O1, 8N1, 8E1, 8O1, 8N1, 7N2, 7E2, 7O2, 8N2, 8E2, 8O2; 8N1].•Flow Control (COM2 only)—RTS/CTS handshaking between the transceiver and the connected device.[Enable, Disable; Disabled]•Serial Mode— If data buffering is Enabled, the radio will oper-ate in seamless mode. Data bytes will be sent over the air as quickly as possible, but the receiver will buffer the data until enough bytes have arrived to cover worst case gaps in trans-mission. The delay introduced by data buffering may range from 22 to 44 ms, but the radio will not create any gaps in the output data stream. This mode of operation is required for protocols such as MODBUS™ and some variants which do not allow gaps in their data transmission. [Seamless, Custom; Seamless]•Seamless Inter-Frame Delay— Number of characters that repre-sent the end of a message (inter-character time-out). MOD-BUS defines a “3.5-character” parameter. [1–65,535; 4]•Custom Data Buffer Size (Custom Packet Mode only)—Maxi-mum amount of characters, that the Remote end will buffer locally before starting to transmit data through the serial port. [16, 32, 64, 128, 256; 32]•Commit Changes and Exit Wizard—Save and execute changes made on this screen (Shown only after changes have been entered.)2.6.5 Configuring for PPP ModeInvisible place holderFigure 2-35. PPP Menu
05-2806A01, Rev. H iNET Series Reference Manual 71•Status—Enable/Disable the serial data port. •IP Protocol—PPP. This is the type of IP port that will be offered by the transceiver’s serial device server. [TCP, UDP, PPP; TCP]•Device IP Address—IP address that will be assigned to the dialing device once the connection is established. [0.0.0.0]•Data Baud—The baud rate of the serial port of the transceiver to which the external device is connected.[1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200; 19200]•Configuration—Byte format of the serial port [7N1, 7E1, 701, 7N2, 7E2, 702, 8N1, 801, 8N2, 8E2, 802; 8N1]•Flow Control (COM2 only)—RTS/CTS handshaking between the transceiver and the connected device. [Enable, Disable; Disabled]•Serial Mode—When seamless mode is selected, data bytes will be sent over the air as quickly as possible, but the receiver will buffer the data until enough bytes have arrived to cover worst case gaps in transmission. The delay introduced by data buffer-ing may range from 22 to 44 ms, but the radio will not create any gaps in the output data stream. This mode of operation is required for protocols such as MODBUS™ that do not allow gaps in their data transmission. [Seamless, Custom; Seamless]•Seamless Inter-Frame Delay— Number of characters that represent the end of a message (inter-character time-out). MODBUS defines a “3.5-character” parameter. [1–65,535; 4]•Custom Data Buffer Size (Custom Packet Mode only)—Maxi-mum amount of characters, that the Remote end will buffer locally before starting to transmit data through the serial port. [16, 32, 64, 128, 256; 32]•Commit Changes and Exit Wizard—Save and execute changes made on this screen (Shown only after changes have been entered.)A PPP session shows the following possible states:•Sending LCP Requests—The PPP server is querying for any cli-ents that need to connect.•Link Established—A successful PPP connection has been negoti-ated and an IP address is assigned.•Port not Enabled—The serial port is disabled.2.6.6 IP-to-Serial Application ExampleYou have a choice to use UDP or TCP to establish communications. This will depend on the type of device you are communicating with at the other end of the IP network. In this example we will use TCP to illus-trate its use. In TCP mode, the transceiver remains in a passive mode offering a socket for connection. Once a request is received, data received at the serial port will be sent out through the IP socket and vice versa, until the
72 iNET Series Reference Manual 05-2806A01, Rev. Hconnection is closed, or the link is interrupted. In this mode, the trans-ceiver behaves the same, whether it is an Access Point or a Remote. (See Figure 2-36 and Table 2-1) NOTE: The TCP session has a timeout of 10 minutes (600 seconds). Ifinactive for that time, it will be closed. The transceiver willoffer the port again for connection after this time expires.Establishing a Connection From the PC, establish a TCP connection to the IP address of the Remote transceiver and to the IP port as configured above (30010—COM1, 30011—COM2). A Telnet client application can be used to establish this connection. Data can now be sent between the PC and the RTU or other connected device.Invisible place holderFigure 2-36. IP-to-Serial Application Diagram2.6.7 Point-to-Multipoint IP-to-Serial Application ExampleThe operation and data flow for this mode is very similar to Point-to-Point serial-to-serial application, except that it uses multicast addressing. The primary difference is that the PC uses UDP to commu-nicate with all of the Remotes. Upon receiving the packet, each Remote strips the data out of the UDP packet and sends it from its COM port. Likewise, data presented at any of the Remotes’ COM ports is pack-etized, sent to the PC using the Access Point (see Figure 2-37 and Table 2-2 on Page 73.EthernetCrosssoverRTUEIA-232Computeror Network192.168.0.10 192.168.0.1 192.168.0.2LANCOM1COM2PWRLINKRemoteAccess PointTable 2-1. Serial Port Application ConfigurationIP-to-Serial Connection Transceiver LocationMenu Item SettingAccess Point None is required None is requiredRemote Unit IP Address 192.168.0.2Status EnabledIP Protocol TCPBaud Rate 9,600 (Example)Flow Control NoneLocal IP Port 30011
05-2806A01, Rev. H iNET Series Reference Manual 73Invisible place holderFigure 2-37. Point-to-Multipoint Serial-to-Serial Application Diagram Invisible place holder192.168.0.3192.168.0.4EthernetTerminalor ComputerRTURTURTUEIA-232EIA-232EIA-232192.168.0.10 192.168.0.1192.168.0.2Access PointRemoteRemoteRemoteTable 2-2. Serial Port Application ConfigurationTransceiver Location Menu Item SettingPC IP Protocol UDPRemote IP Address 224.254.1.1—Multicast Address1Local IP Port 30011 Access Point (COM2)2N/A None requiredRemote Units (COM2)1Enable EnabledBaud Rate 2,400 (Example)Serial Mode Custom Flow Control Hardware (Example)IP Protocol UDPRemote IP Address 192.168.0.1Remote IP Port 30011 Local IP Port 30011 Local Multicast Address224.254.1.1 —Multicast Address2 1. This address is an example only. Any Class D IP address (224.0.0.0–239.255.255.255) will work.2. Either COM port can be used, but they must be the same ones at both ends of the link. Both COM ports can be used simultaneously for two independent data channels.
74 iNET Series Reference Manual 05-2806A01, Rev. HFigure 2-38. Remote Radio Serial Port Configuration2.6.8 Point-to-Point Serial-to-Serial Application ExampleOnce the transceivers are configured and the changes have been exe-cuted, they begin processing any data presented at the COM ports. Data presented at the Access Point’s COM port will be packetized and sent via UDP to the Remote. Upon receiving the packet, the Remote strips the data out of the UDP packet and sends it out its COM port. Likewise, data presented at the Remote’s COM port is packetized, sent to the Access Point, stripped, and sent out the Access Point’s COM port. Note, this configuration does not use multicast addressing.Invisible place holderFigure 2-39. Point-to-Point Serial-to-Serial Application DiagramEIA-232RTUEIA-232Terminalor Computer192.168.0.10 192.168.0.1 192.168.0.2RemoteAccess PointLANCOM1COM2PWRLINKTable 2-3. Serial Port Application Configuration  Transceiver Location Menu Item SettingAccess Point (COM2)1Status EnabledData Baud Rate 9,600 (Example)Flow Control Hardware (Example)Serial Mode SeamlessSIFD 4IP Protocol UDP
05-2806A01, Rev. H iNET Series Reference Manual 752.6.9 Combined Serial and IP Application ExampleNote that in this example, the TCP mode does not involve the Access Point. Thus, the transceiver in a single network can run in both modes at the same time. In other words, some Remotes can be configured for TCP mode while others can be configured (along with the Access Point) for UDP mode.In this configuration, the Host PC can use both data paths to reach the RTUs. This may be helpful when a mixed collection of RTUs is present where some RTUs can operate in a broadcast form while others cannot (see Figure 2-40 on Page 76 and Table 2-4 on Page 76).Operation and Data Flow• Communicate with RTU A by Telneting to Remote 1, port 30011.• Communicate with RTU B by Telneting to Remote 2, port 30011.• Communicate with RTUs C and D by sending and receiving data from the Access Point’s COM port.• All communication paths can be used simultaneously.Remote IP Address192.168.0.2(IP address of the Remote radio)Remote IP Port 30011 Local IP Port 30011Remote Unit (COM2)1Status EnabledData Baud Rate 9,600 (Example)Flow Control X-ON/X-OFF (Example)Serial Mode Seamless SIFD 4 (Characters)IP Protocol UDPRemote IP Address192.168.0.1(IP address of the AP)Remote IP Port 30011 Local IP Port 300111. Either COM port can be used, but they must be the same ones at both ends of the link. Both COM ports can be used simultaneously for two independent data channels.Table 2-3. Serial Port Application Configuration   (Continued)Transceiver Location Menu Item Setting
76 iNET Series Reference Manual 05-2806A01, Rev. HInvisible place holderFigure 2-40. Mixed-Modes Application DiagramEIA-232Terminalor ComputerRTU–CEIA-232EIA-232EIA-232RTU–DEIA-232LANCOM1COM2PWRLINKiNET 900Remote 4EthernetCrosssoverRTU–BRTU–AiNET 900Access PointLANCOM1COM2PWRLINKiNET 900Remote 1LANCOM1COM2PWRLINKiNET 900Remote 2LANCOM1COM2PWRLINKiNET 900Remote 3Table 2-4. Serial Port Application Configuration  Transceiver Location Menu Item SettingAccess Point Status EnabledBaud Rate 9,600Flow Control DisabledIP Protocol UDPSend to Address A multicast IP address such as 224.254.1.1Send to Port 30011 Receive on Port 30011 Receive on Address 0.0.0.0 (Not Used)Remote Units 1 & 2 (COM2)Status EnabledBaud Rate 2,400Flow Control DisabledIP Protocol TCPReceive on Port 30011 Remote Units 3 & 4 (COM2)Status EnabledBaud Rate 9,600Flow Control DisabledIP Protocol UDPSend to Address IP address of the APSend to Port 30011 Receive on Port 30011 Receive on Address 224.254.1.1(The multicast IP address used for the AP’s Send To Address above)
05-2806A01, Rev. H iNET Series Reference Manual 772.6.10 Virtual LAN in iNET-II and iNETThe iNET-II and iNET radios support port-based VLAN at the Ethernet interface and over the air, as specified by the IEEE 802.1Q standard.A VLAN creates independent logical networks within a physical net-work. It allows communications as if all stations and switches are con-nected to the same physical LAN segment. Members of a VLAN receive frames only from other members of the same VLAN.The iNET-II and iNET radios act as an Ethernet switch with two inter-faces: the wireless interface is always a trunk port, while the Ethernet interface is configured as either a trunk port or an access port. A trunk port expects incoming frames to have a VLAN ID, and sends outgoing frames with a VLAN tag as well. The radio’s trunk port also supports Native VLAN, which allows the transmission and reception of untagged frames. The radio does not support Generic Attribute Registration Pro-tocol (GVRP).The Ethernet port of an Access Point radio is normally configured as a trunk port, and is connected to a VLAN-aware switch or router. You can configure the Ethernet port of a remote radio as an access port or as a trunk port:• When the Ethernet interface is configured as an access port, incom-ing traffic is tagged with a VLAN ID, and outgoing traffic is sent without a tag. This traffic is assigned to the DATA VLAN. A second VLAN, known as the MANAGEMENT VLAN, is used for traffic targeted at the radio, such as SNMP, TFTP, ICMP, Telnet, and so on. Traffic directed to the transceiver’s integrated terminal server, which controls the serial ports, is assigned to the DATA VLAN.• When the Ethernet interface is configured as trunk port, the trans-ceiver bridges all frames to and from the wireless link with the unchanged VLAN tag. Untagged frames are also bridged transpar-ently.NOTE: The Ethernet port in an iNET-II or iNET radio is 10BaseT.Some Ethernet switches allow a VLAN trunk port only on a100BaseT interface, and might not be compatible with thetransceiver.
78 iNET Series Reference Manual 05-2806A01, Rev. HConfiguring for Operation with VLANFigure 2-41. Network Interface Configuration Menu•VLAN Status—When enabled, the transceiver uses an 802.1Q frame structure.•Data VLAN ID—Defines the VLAN ID assigned to the traffic that is directed to and from the transceiver’s Ethernet port and the terminal server process. The transceiver uses this VLAN ID for filtering and tagging purposes. [1-4094; 3]•Management VLAN Mode—Defines whether frames belonging to the management VLAN are tagged or untagged [Native].•Config Management IP—Opens the Configuration Management IP menu.•Config Data IP—Opens the Configuration Management IP menu.2.7 CYBER SECURITY CONFIGURATIONThe cyber security features of the transceiver are grouped into three gen-eral areas: controlling access to the radio itself for configuration and management purpose (Device Security), controlling how and when radios communicate with each other, as well as how data traffic is han-dled (Wireless Security) and a special section dealing with authentica-tion and authorization using a central server (RADIUS Configuration). Figure 2-42 shows the Security Configuration Menu, which is the entry point for these categories.
05-2806A01, Rev. H iNET Series Reference Manual 79Figure 2-42. Security Configuration Menu(Access Point Version Shown)2.7.1 Device SecurityThis group of features controls how the radios can be accessed either locally or remotely for configuration and management.Invisible place holderFigure 2-43. Device Security Menu•User Auth Method— Defines whether username and password is verified locally or via a central server. [Local, RADIUS; Local]•User Auth Fallback— Defines the alternate authentication mode in case the authentication server is not available.[Local, None; Local]•User Password—Local password for this unit. Used at log-in via COM1 Port, Telnet, SSH and Web browser. [Up to 8 alphanumeric characters without spaces (case-sensitive); admin]
80 iNET Series Reference Manual 05-2806A01, Rev. HTIP: For enhanced security, consider using misspelled words, a combi-nation of letters and numbers, and a combination of upper and lower case letters. Also, the more characters used (up to eight), the more secure the password will be. These strategies help protect against sophisticated hackers who may use a database of common words (for example, dictionary attacks) to determine a password.•SNMP Mode—This specifies the mode of operation of the radio’s SNMP Agent. If the mode is disabled, the Agent does not respond to any SNMP traffic. If the mode is v1_only, v2_only, or v3_only, the Agent responds only to that version of SNMP traffic. If the mode is v1-v2, or v1-v2-v3, the Agent responds to the specified version of SNMP traffic.[disabled, v1_only, v2_only, v3_only, v1-v2, v1-v2-v3; v1-v2-v3]•Telnet Access—Controls remote access through Telnet sessions on Port 23 [Enabled, Disabled; Enabled]•SSH Access— Controls remote access through SSH (Secure Shell) sessions on Port 22 [Enabled, Disabled; Enabled]•HTTP Mode— Controls remote access through HTTP sessions on Ports 80 and 443. Selecting HTTPS forces secure connections to Port 443. When HTTP Mode is disabled, access through HTTP or HTTPS is not allowed. [Disabled, HTTP, HTTPS; HTTP]•HTTP Auth Mode—Selects the method of HTTP log-in authenti-cation. This parameter functions only when HTTP is selected in the previous menu item. Although the Basic Auth mode requests a password, the actual password text is transmitted in the clear (unencrypted). [Basic Auth, MD5 Digest; Basic Auth]2.7.2 Wireless SecurityThe features in the Wireless Security menu control the communication of data across the wireless link. The radios can be authenticated locally via a list of authorized radios, or remotely via a centralized RADIUS server. RADIUS is a centralized authentication mechanism based on standards.
05-2806A01, Rev. H iNET Series Reference Manual 81Invisible place holderFigure 2-44. Wireless Security Menu•Device Auth Method—Controls whether device authentication is executed locally, via a central server, or not at all. Selecting Local uses the Approved Remotes List described later in this manual. [None, Local, RADIUS; None]•Encryption— When enabled, it forces the transceiver to use AES-128 encryption (RC4-128 on iNET) on all over-the-air messages. This option requires the Encryption Phrase to be pre-viously configured. Both the AP and the Remote radios must use the same encryption phrase. (Some units may not be autho-rized to use encryption. “See “Authorization Keys Menu” on Page 108” for additional details.) [Enabled, Disabled; Disabled]•Auto Key Rotation—When enabled, it forces the transceiver to use the key rotation algorithm to generate a new encryption key after 500 kilobytes of information has been transmitted, or one hour has elapsed. [Enabled, Disabled; Disabled]•Approved Access Points/Remotes List —Displays a menu to man-age the list of other radios with which this unit will be permitted to communicate.•Encryption Phrase—Phrase (text & numbers) that will be used by the encryption algorithm.[8 to 29 alphanumeric characters; Blank]•Force Key Rotation— It triggers an immediate key rotation of the encryption keys before the internal counters do it automatically.Local Authentication—Approved Remotes/Access Points List SubmenuSetting the Device Auth Method to Local forces the transceiver to check the Approved AP List before a radio link can be established. In the case of a Remote, the AP must be in the Approved Access Points List before it accepts the beacon as being valid. In the case of an AP, a Remote must be in the Approved Remotes List to be granted authorization. Before enabling this option, at least one entry must already exist in the Approved AP/Remotes List.
82 iNET Series Reference Manual 05-2806A01, Rev. HThis menu is the same for both Access Points and Remotes and the names change to reflect their mode. Replace “Remotes” with Access Points” in the following description.NOTE: The limit for Remotes (in an Access Point radio) is 255. Thelimit for Access Points (in a Remote radio) is 104. Figure 2-45. Approved Remotes List Menu•Add Remote—Enter MAC address of Remote.[Any valid 6-digit hexadecimal MAC address; 00:00:00:00:00:00] •Delete Remote—Enter MAC address of Remote. For security purposes, you may want to delete a stolen or deprovisioned radio from this list.•Add Associated Remotes—Add all currently associated remotes to the approved remote list. Alternatively, you can enter each Remote MAC manually.•Delete All Remotes—Remove (complete purge) of all Remotes from current list.•View Approved Remotes—Simple listing of approved Remotes by MAC address, of radios authorized to join this AP. If a Remote is not in this list, it will not be able to associate with this AP.•Save Changes—Saves all changes made during the session with this menu. Changes are implemented only if they are “saved” before exiting this menu.2.7.3 RADIUS ConfigurationThis section covers the authentication settings needed for the iNET radios to access the RADIUS server, which is used for Device Level Security and for Wireless Access Security. GE MDS does not provide the RADIUS server software.
05-2806A01, Rev. H iNET Series Reference Manual 83Operation of Device AuthenticationDevice authentication forces the radio to authenticate before allowing user traffic to traverse the wireless network. When Device Security is configured to use RADIUS as the Authentication Method, Remote radios need three types of certificates: public (client), private, and root (Certificate Authority). These files are unique to each Remote radio and need to first be created at the server and then installed into each unit via TFTP. The certificate files must be in DER format.Device authentication uses the serial number of each radio as the Common Name (CN) in its certificate and in its RADIUS identity field. Each Access Point and Remote radio must be identified/recognized by the RADIUS Server through the Common Name (Serial number) and IP address entries.NOTE: Consult your RADIUS network administrator for assistance inconfiguration, or for help with other issues that may arise.To activate device authentication, select Device Auth Method and set RADIUS as the active mode. The behavior of this setting differs depending on whether it is implemented on an Access Point or a Remote transceiver. An explanation of these behaviors is given below:Access Point: When Device Auth Method is set to RADIUS, the AP disasso-ciates all associated Remotes and waits for the RADIUS Server to Authenticate the Remotes before allowing data to be passed from them. When approval is received from the RADIUS Server, data from the Remote is allowed to pass.Remote: When Device Auth Method is set to RADIUS, the Remote halts any data it is passing, and requests Authentication from the RADIUS Server. If accepted, data is allowed to be transmitted.Operation of User AuthenticationWhen user authentication is set to Local or RADIUS, you must enter a valid user name and password before being allowed to manage the radio. In RADIUS mode both of these fields may be up to 40 characters long. In Local mode the user name is iNET and the password may be up to 8 char-acters long.When set to RADIUS, all logins to the local configuration services are required to be authenticated via the RADIUS Server, including telnet and SSH (Secure Shell) sessions. Authentication must be accepted before access to the radio menu is granted.
84 iNET Series Reference Manual 05-2806A01, Rev. H2.7.4 RADIUS ConfigurationInvisible place holderFigure 2-46. RADIUS Configuration Menu•Server IP Address—Used to set/display address of the Server where the RADIUS application resides. •Server IP port—1812 is the standard port for authentication (RFC 2865, June 2000), but this setting may be changed if necessary to any number between 1 and 65535. [1-65535; 1812]•Shared Secret—User authentication and Device authentication require a common shared secret to complete a RADIUS trans-action. This entry must match the string used to configure the appropriate files on the RADIUS Server.•User Auth Mode—Should be set to PAP or CHAP depending on the configuration of the server.NOTE: CHAP is more secure than PAP. PAP may display the loginpassword in log files at the RADIUS Server while CHAP willencrypt the login password.NOTE: The security password may not exceed 40 characters in length.2.7.5 Certificate Management (Remote transceivers only)Use Certificate generation software to generate certificate files and then install these files into each Remote unit via TFTP. The certificate files must be in DER format. The Common Name (CN) field in the public certificate file must match the serial number of the unit it will be installed in.
05-2806A01, Rev. H iNET Series Reference Manual 85Invisible place holderFigure 2-47. Manage Certificates Menu(NOTE: The appearance of this screen differs from the others because a different terminal program was used; Menu content is the same regardless of program.)•Server IP Address—the IP address of the Server where the RADIUS application resides.•TFTP Timeout should be set appropriately according to the layout of the network.Three certificate files (Root, Client, and Private Key) must be present in each of the Remote radios. Use the commands described below to install these files into each Remote radio.•Certificate Filename—Used to specify the filename of the certifi-cate file residing on the TFTP server.•Certificate Type—Selects one of the three file types mentioned above. [Root Certificate, Client Certificate, Private Key Certificate; Root Certificate]•Retrieve Certificate—Initiates the retrieval of the certificate file from the storage location. A successful installation issues a Com-plete status message.NOTE: It is imperative that the three certificate files are installedcorrectly into the Remote radio, in their respective file types.If they are not, it will render the Remote un-authenticated fordata traffic. Consult your RADIUS network administrator ifissues arise.2.8 PERFORMANCE VERIFICATIONAfter the basic operation of the radio has been checked, you may wish to optimize the network’s performance using some of the following sug-gestions. The effectiveness of these techniques will vary with the design of your system and the format of the data being sent.
86 iNET Series Reference Manual 05-2806A01, Rev. HThere are two major areas for possible improvement—the radio and the data network. The following sections will provide you with a variety of items to check and on many occasions, ways to correct or improve their performance.The menu/screen shown in Figure 2-48 is one of two primary sources of information on the radio layer and radio network performance.Figure 2-48. Performance Information Menu(AP Version Shown)•RF Output Power (Display only)—Measured power output. (See “How Much Output Power Can be Used?” on Page 135)•Signal-to-Noise (Display only)—Current running-average SNR value all active operating frequencies. (No value displayed on APs) NOTE: The RSSI is an average of the last 20 RSSI samples. The RSSIvalue is reset every time the radio returns to scanning mode.•(Display only)—Current running-average Received Signal Strength Indication for all active operating frequencies. (No value displayed on APs.) •Actual Data Rate (Display only)—Over-the-air transmission rate (as opposed to selected data rate) for the remote being monitored. The fastest data rates can generally be achieved with stronger signal levels.•RSSI by Zone—Received Signal Strength Indicator by Zone. (See “RSSI by Zone Menu (Remotes Only)” on Page 87)•Event Log—Access the menu for managing the unit’s log of operational activities.(See “Authorization Key—Alter the unit’s overall capabilities by enabling the built-in resources. (See “Authorization Keys Menu” on Page 108)” on Page 100)
05-2806A01, Rev. H iNET Series Reference Manual 87•Packet Statistics—Multiple radio and network operating statis-tics. (See “Packet Statistics Menu” on Page 91)•Wireless Network Status (Displayed only at Remotes)—Current associ-ation state and MAC address of the Access Point. (See “Wireless Network Status (Remotes Only)” on Page 94)•Remote Listing (AP Display only) —List of basic information for all Remote units currently associated with this Access Point. (See “Remote Listing Menu (Access Points Only)” on Page 96) •Endpoint Listing (AP Display only)—List of units accessible by this AP through associated Remote ports. (See “Endpoint Listing Menu (Access Points Only)” on Page 97)•Remote Performance Listing (AP Display only)—(See “Remote Per-formance Listing Menu (Access Points Only)” on Page 98) 2.8.1 RSSI by Zone Menu (Remotes Only)This screen displays the strength of RF signals received from the cur-rently associated Access Point. Network integrity depends in large part on stable radio signal levels being received at each end of a data link. In general, signal levels stronger than –80 dBm will provide reliable communication that includes a 15 dB fade margin.If you find there is a poor signal level on one zone, check the Packet Sta-tistics Menu  section on Page 91 and record the values. Then, set the questionable zone to “Skipped” in the Radio Configuration Menu (Page 51) and look for an improvement in the Packet Statistics error rates. If there is none, return the Zone to “Active.”RSSI measurements and Wireless Packet Statistics are based on mul-tiple samples over a period of several seconds. The average of these measurements will be displayed by the Management System.
88 iNET Series Reference Manual 05-2806A01, Rev. HFigure 2-49. RSSI by Zone MenuTIP: Under normal circumstances, the signal levels in each zone should be within a few decibels of each other. If you see one that is signif-icantly lower or higher, it may be a sign of radio frequency inter-ference from another signal source on the 900 MHz band. See “PERFORMANCE NOTES” on Page 144 for further infor-mation.2.8.2 Event Log MenuThe transceiver’s microprocessor monitors many operational parame-ters and logs them. Events are classified into four levels of importance, which are described in Table 2-5. Some of these events will result from a condition that prevents the normal of the unit—these are “critical” events. These will cause the unit to enter an “alarmed” state and the PWR LED to blink until the condition is corrected. All events are stored in the Event Log that can hold up to 8,000 entries.Time and DateThe events stored in the Event Log are time-stamped using the time and date of the locally connected device. Remote units obtain this informa-tion from the Access Point when they associate with it. The Access Point Table 2-5. Event ClassificationsLevel Description/ImpactInformational Normal operating activitiesMinor Does not affect unit operationMajor Degraded unit performance but still capable of operationCritical Prevents the unit from operating
05-2806A01, Rev. H iNET Series Reference Manual 89obtains the time and date from a Time Server. This server can generally be provided by a standard Windows PC server SNTP application. In the absence of the SNTP services, the user must manually enter it at the Access Point. (See “Device Information” on Page 35 for SNTP server identification.) The manually set time and date clock is dependent on the unit’s primary power. A loss of power will reset the clock to January 1, 2002 but will not affect previously stored error events.Figure 2-50. Event Log Menu •Current Alarms (Telnet/Terminal only)—View list of root causes that have placed the Device Status in the alarmed state. (See “Alarm Conditions” on Page 120)•View Log—View a list of events stored in the current log. Some of these events are stored in volatile memory and will be erased with a loss of power. The events are numbered for easier iden-tification and navigation.•Clear Log—Purges the log of all eventsTIP: Save your Event Log before choosing to clear it in order to retain potentially valuable troubleshooting information. (See “Upgrading the Firmware” on Page 102 for an over-view on how to transfer files from the transceiver to a com-puter on the network using TFTP.)•Send Log (Telnet/Terminal only)—Initiate TFTP transfer of the unit’s event Event Log in a plain text (ASCII) file to a TFTP server at the remote location.•TFTP Host Address (Telnet/Terminal only)—IP address of the com-puter on which the TFTP server resides. This same IP address is used in other screens/functions (reprogramming, logging, etc.). Changing it here also changes it for other screens/functions.[Any valid IP address; 127.0.0.1]
90 iNET Series Reference Manual 05-2806A01, Rev. H•Filename (Telnet/Terminal only)—Name to be given to the Event Log file sent to the TFTP server for archiving. [Any 40-char alphanumeric string; Blank]NOTE: You may want to change the filename to reflect the type of log you intend to archive and/or its date. •TFTP Time-out (Telnet/Terminal only)—Time in seconds the TFTP server will wait for a packet ACK (acknowledgment) from the transceiver before canceling the file transfer.[10 to 120 seconds; 10]•Syslog Server—IP address to which alarms are sent using the sys-log message format. [Any valid IP address; 0.0.0.0]View Current AlarmsMost events, classified as “critical” will make the PWR LED blink, and will inhibit normal operation of the transceiver. The LED will remain blinking until the corrective action has been completed.An alarm condition is different from a log event in the sense that an alarm is persistent in nature. That is, an alarm condition remains as an alarm until it has been cleared by correcting the cause (see Table 3-6 on Page 122 for corrective action).Figure 2-51. Current Alarms Screen
05-2806A01, Rev. H iNET Series Reference Manual 91View Event LogSee Table 3-4 on Page 120 for event classifications.Figure 2-52. Sample Event Log Screen2.8.3 Packet Statistics MenuAn iNET radio maintains running counters of different categories of events in the Ethernet protocol. The Packet Statistics refer to each Ethernet interface from the perspective of the radio.Figure 2-53. Sample Packet Statistics MenuWireless Packet Statistics•Packets received—Over-the-air data packets received by this unit
92 iNET Series Reference Manual 05-2806A01, Rev. H•Packets sent—Over-the-air data packets sent by this Remote.•Bytes received—Over-the-air data bytes received by this Remote.•Bytes sent—Over-the-air data bytes sent by this Remote.•Packets dropped—To-be-transmitted packets dropped as a result of a lack of buffers in the RF outbound queue.•Receive errors—Packets that do not pass CRC. This may be due to transmissions corrupted by RF interference.•Retries—Number of requests to re-send a data packet before it is acknowledged. If the packet was not acknowledged, this counter is not incremented.•Retry errors—Packets discarded after exceeding seven retries over-the-air.•Clear Wireless stats—Resets the statistics counter.Ethernet Packet Statistics•Packets received—Packets received by the transceiver through the Ethernet port.•Packets sent—Packets transmitted by the transceiver through the Ethernet port.•Bytes received—Data bytes received by this Remote through its LAN port.•Bytes sent—Data bytes sent by this Remote.•Packets dropped—Received packets dropped as a result of a lack of buffers.•Receive errors—Packets that do not pass CRC. This may be due to collisions in the Ethernet LAN.•Lost carrier detected—A count of the number of packets that the unit attempted to send out the Ethernet port when the carrier sig-nal of the Ethernet was not present. (No carrier present could be due to a loose connection, bad or wrong cable, or equipment failure at the other end of the Ethernet cable.)•Clear Ethernet stats—Resets the statistics counter.•Wireless Packet Statistics (when VLAN is shown)—A screen almost identical to Figure 2-53 is shown, except that option D (VLAN Packet Stats) appears as in Figure 2-54 below.
05-2806A01, Rev. H iNET Series Reference Manual 93Invisible place holderFigure 2-54. Sample Packet Statistics MenuThe VLAN Packet Statistics Menu (Figure 2-55) groups the statistics of both wired and wireless interfaces. The numbers have different meaning depending on whether the Ethernet port is defined as an Access Port or as a Trunk Port.Invisible place holderFigure 2-55. VLAN Packet StatisticsPackets Received by ZoneThis screen, shown in Figure 2-56, presents a breakdown of wireless packet statistics by-zone. All zones should report similar numbers. If one or more zones report lower numbers than the others (2% reduction), the specific zone is probably experiencing interference. An improve-ment can be realized by blocking this zone (see Main Menu>>Radio Config-uration>>Skip Zone Option).
94 iNET Series Reference Manual 05-2806A01, Rev. HInvisible place holderFigure 2-56. Packets Received By Zone Menu2.8.4 Wireless Network Status (Remotes Only)The Wireless Network Status screen provides information on a key operating process of the transceiver—the association of the Remote with the Access Point. The following is a description of how this process takes place and as monitored on the Figure 2-57. Wireless Network Status Screen" on page 95.The Transceiver’s Association ProcessAfter the Remote is powered up and finishes its boot cycle, it begins scanning the 900 MHz band for beacon signals being sent out from AP units. If the Remote sees a beacon with a Network Name that is the same as its own, the Remote will stop its scanning and temporarily synchro-nize its frequency-hopping pattern to match the one encoded on the AP’s beacon signal. The Remote waits for three identical beacon signals from the AP and then it toggles into a fully synchronized “associated” state. If the Remote does not receive three identical beacons from the Access Point unit within a predetermined time period, it returns to a scanning mode and continues to search for an AP with a matching network name in its beacon. Under normal circumstances, the association process should be com-pleted within 20 seconds after boot-up. This time can vary depending on the beacon period setting at the AP. See Beacon Period description in Sec-tion 2.5.1, Radio Configuration Menu (beginning on Page 51).Remote units are always monitoring the beacon signal. If an associated Remote loses the AP’s beacon for more than 20 seconds, the association process starts again.
05-2806A01, Rev. H iNET Series Reference Manual 95The Wireless Network Status Screen (Remotes Only)Figure 2-57. Wireless Network Status Screen•Connection Status—Current state of the wireless network com-munication. •Scanning—The unit is looking for an Access Point beacon signal.•Exp(ecting) Sync(hronization)—The unit has found a valid beacon signal for its network.•Hop Sync—The unit has changed its frequency hopping pat-tern to match that of the Access Point.•Connected —The unit has established a radio (RF) connec-tion with the Access Point, but has not obtained cyber-secu-rity clearance to pass data.•Associated —This unit has successfully synchronized and associated with an Access Point. This is the normal status.•Alarmed—The unit is has detected one or more alarms that have not been cleared.•Current AP Mac Address—Wireless address of Access Point with which the Remote is associated.•Current AP IP Address—IP address of Access Point with which the Remote is associated.•Association Date—Date of last successful association with an Access Point.•Association Time—Time of day association was established on the association date.• Latest AP Firmware Version• AP Auto Upgrade• AP Reboot when Upgraded
96 iNET Series Reference Manual 05-2806A01, Rev. H2.8.5 Remote Listing Menu (Access Points Only) Figure 2-58. Remote Listing Menu(List of transceivers associated with this AP)•MAC Address—Hardware address of the Remote transceiver.•IP Address—IP Address of the Remote transceiver.•State—Current association state of the Remote transceiver.•AgeTime—Time, in minutes, remaining before the device (address) will be deleted from the table.Each transceiver maintains a table with the addresses of the devices it communicates with. The age-time countdown is restarted to 5 minutes every time a message to/from that device is detected. If no traffic is exchanged with that device, it then “ages out” of the table. When traffic is detected it is included again in the table. This opti-mizes memory space utilization.•DataRate—Supported data rate by this unit.
05-2806A01, Rev. H iNET Series Reference Manual 972.8.6 Endpoint Listing Menu (Access Points Only)This list shows all of the non-iNET 900 Ethernet devices that are known to the transceiver and is equivalent to the ARP table of IP devices. Figure 2-59. Endpoint Listing Menu(Lists all equipment attached to REMOTE transceivers in the network)•MAC Address—Hardware address of endpoint device.•IP Address—IP Address of endpoint device.•AgeTime—Time, in minutes, remaining before the device (address) will be deleted from the table. Each AP maintains a table with the addresses of the remote radios it communicates with. The age-time countdown is restarted to 5 min-utes every time a message to/from that remote is detected. If no traf-fic is exchanged with that remote, it then “ages out” of the table. When traffic is detected it is included again in the table. This opti-mizes memory space utilization.•via Remote—Hardware address of the radio connected to this device.•RxPkts—Over-the-air data packets received by the transceiver. and passed on to the endpoint device.•TxPkt—Number of packets received from the endpoint device and passed over-the-air.
98 iNET Series Reference Manual 05-2806A01, Rev. H2.8.7 Remote Performance Listing Menu (Access Points Only) Figure 2-60. Remote Performance Listing Menu for iNET AP(iNET-II will show RxRate as 512 kbps or 1024 kbps)This screen provides a unit-by-unit summary of all Remote units cur-rently associated with this Access Point. The parameters are displayed in a column format with each line corresponding to one Remote.•RxRate—Over-the-air data rate the radio is currently using. All transceivers do not need to use the same rate.•RxPkts—Over-the-air data packets received from this unit.•TxPkts—Over-the-air data packets sent to this unit.•RxBCMC—Total number of Broadcast and/or Multicast packets received over-the-air.•RxViaEP—Packets received by the transceiver through the Ether-net port.•TxViaEP—Packets sent by the transceiver through the Ethernet port.•RetryEr—Packets discarded after exceeding five retries over-the-air.
05-2806A01, Rev. H iNET Series Reference Manual 992.8.8 Serial Data Statistics MenuThis screen provides a summary of port activity for both serial data ports. These values will be reset to zero after a reboot cycle. Figure 2-61. Serial Data Statistics Screen(Both COM1 and COM2 will be shown)•Bytes in on port—Number of bytes received by the transceiver through the serial interface•Bytes out on port—Number of bytes transmitted by the trans-ceiver through the serial interface•Bytes in on socket—Number of bytes received by the trans-ceiver through the IP socket•Bytes out on socket—Number of bytes transmitted by the trans-ceiver through the IP socketIn general, the number of bytes Out on Socket should follow the number of bytes In On Port as all bytes received on the serial port should be transmitted out to the IP interface. The same should be true in the opposite direction, bytes Out On Port should follow bytes In On Socket.•Clear Com1 Statistics—Resets counter to zero.•Clear Com2 Statistics—Resets counter to zero.2.9 MAINTENANCEIn the normal course of operating a wireless network, you will want to take advantage of product improvements, and to read and archive the configuration of your individual transceivers using the Maintenance Menu. This section provides detailed information on how to take advan-tage of these services.The maintenance tasks are:
100 iNET Series Reference Manual 05-2806A01, Rev. H•Reprogramming— Managing and selecting the unit’s operating system firmware resources. (See “Reprogramming Menu” on Page 100)•Configuration Scripts—Saving and importing data files contain-ing unit operating parameters/settings. (See “Configuration Scripts Menu” on Page 105)•Authorization Key—Alter the unit’s overall capabilities by enabling the built-in resources. (See “Authorization Keys Menu” on Page 108)•Auto-Upgrade/Remote-Reboot—Configure when remotes retrieve new firmware versions from the associated AP, and whether or not they reboot to the new firmware after receiving the new firmware. (See “Auto-Upgrade/Remote-Reboot Menu” on Page 108)•Radio Test—A diagnostic tool for testing RF operation. (See “Radio Test Menu” on Page 110)•Ping Utility—Diagnostic tool to test network connectivity. (See “Ping Utility Menu” on Page 111)Figure 2-62. Maintenance/Tools Menu2.9.1 Reprogramming MenuThe transceiver has two copies of the firmware (microprocessor code) used for the operating system and applications. One copy is “active” and the second one is standing by, ready to be used once activated. You can load new firmware into the inactive position and place it in service whenever you desire.From time-to-time GE MDS offers upgrades to the transceiver firm-ware. Loading new firmware into the unit will not alter any privileges provided by Authorization Keys and does not require the transceiver be
05-2806A01, Rev. H iNET Series Reference Manual 101taken off-line until you want to operate the unit from the newly installed firmware image.Firmware images are available free-of-charge at:www.GEmds.com/service/technical/supportNOTE: GE MDS iNET firmware may not be installed in GE MDSiNET-II radios, or vice-versa.NOTE: When upgrading to firmware 6.0.0 or later, the unit createsinternal files following the first reboot. This one-time processdelays the response of the HTTP interface for 5-10 minutes. IfDC power is cycled (turned off and back on) during thisprocess, the files will have to be created again. It is recom-mended that you wait until this 5-10 minute process iscomplete before verifying operation of HTTP, HTTPS, orSSH.NOTE: Always read the release notes for downloaded firmware. Someversions may not be compatible over the air, or with the partic-ular unit you have.Figure 2-63. Reprogramming Menu(Shown with “Image Copy” Selected)•TFTP Host Address—IP address of the host computer from which to get the file. [Any valid IP address] This same IP address is used in other screens/functions (reprogramming, logging, etc.). Changing it here also changes it for other screens/functions.•Filename—Name of file to be received by the TFTP server.[Any 40-character alphanumeric string] Verify that this corresponds to the TFTP directory location. May require sub-directory, for example: \firmware\inet\inet-4_4_0.ipk.
102 iNET Series Reference Manual 05-2806A01, Rev. H•TFTP Timeout—Time in seconds the TFTP server will wait for a packet ACK (acknowledgment) from the transceiver before canceling the file transfer. [2 to 60 seconds; 10]•Retrieve File—Initiates the file transfer from the TFTP server. The new file is placed into inactive firmware image. [Y, N ]•Image Verify—Initiate the verification of the integrity of firmware file held in unit.•Image Copy—Initiate the copying of the active firmware into the inactive image.•Reboot Device—Initiate rebooting the transceiver. This will interrupt data traffic through this unit, and the network if per-formed on an Access Point. Intended to be used to toggle between firmware images.NOTE: See “Upgrading the Firmware” on Page 102 for details on setting up the TFTP server.Upgrading the FirmwareFirmware images are available free-of-charge at:www.GEmds.com/service/technical/supportNOTE: GE MDS iNET firmware may not be installed in GE MDSiNET-II radios, or vice-versa.To install firmware by TFTP, you will need:• A PC with a TFTP server running.• The IP address of the PC running the TFTP server.• A valid firmware fileThe IP address of the radio can be found under the Management Sys-tems’ Configuration menu. (See “Network Configuration Menu” on Page 37.)A TFTP server is available on the GE MDS Web site at:www.GEmds.com/service/technical/support/downloads.asp TIP: If you do not know your computer’s address on a Windows PC, you can use the RUN function from the Start menu and enter winipcfg or ipconfig to determine your local PC’s IP address. There are several alternatives to connecting the transceiver for firmware upgrade. Figure 2-64 and Figure 2-65 show two variations. It is essen-tial all of the equipment be on the same subnet.
05-2806A01, Rev. H iNET Series Reference Manual 103Invisible place holderFigure 2-64. Firmware Upgrade Setup—Option 1(TFTP Server and Firmware File on Same CPU)Invisible place holderFigure 2-65. Firmware Upgrade Setup—Option 2(TFTP Server and Firmware File on Remote Server)NOTE: The LAN and COM1 ports share a common data channel whenloading firmware over-the-air. Transferring the radio firmwareimage file (≈ 3 Mb), may take several minutes depending ontraffic between the TFTP server and the transceiver. Regardless of your connection to the transceiver, loading firm-ware/configuration files into the unit’s flash-RAM is muchslower than loading software onto a PC hard drive or RAM.Upgrade Procedure To load a new firmware file (filename.ipk) into the transceiver, use the following procedure:LAN COM1 COM2 PWR LINKLANPORTLOCAL WINDOWS PCWITH iNET FILESIP ADDRESS: 172.0.0.AIP ADDRESS: 172.0.0.BTFTPSERVER& TELNETMDS iNET 900CROSS-OVERCABLEINITIATE UPLOADFROM HERETFTPSERVER ETHERNETPORTCOM1PORT(DCE)INITIATE UPLOADFROM HEREREMOTE  PCW/FIRMWARE FILESHUB/LAN/WAN/MANTCP/IPLANPORTCOM1, 2, ETC.(DTE)IP ADDRESS: w.x.y.zLOCAL WINDOWS PCAP or REMOTELAN COM1 COM2 PWR LINKIP ADDRESS: 172.0.0.AIP ADDRESS: 172.0.0.BTERMINALPROGRAM9-PINSERIALCABLE
104 iNET Series Reference Manual 05-2806A01, Rev. H1. Launch a TFTP server on a PC connected either directly or via a LAN to the Ethernet port (LAN) of the radio. Point the server towards the directory containing the firmware image file.2. Connect to the Management System by whichever means is conve-nient: Browser or Telnet via the LAN, or Terminal emulator via the COM1 port.3. Go to the MS Reprogramming Menu. (Main Menu>>Maintenance Menu>>Reprogramming Menu)4. Fill in the information for the:•TFTP Host Address—IP Address of server (host computer) run-ning TFTP server.•Retrieve File—Name of file (filename.ipk) to be pulled from the TFTP server holding the firmware file.5. Pull the firmware file through the TFTP server into the transceiver.(Main Menu>>Maintenance Menu>>Reprogramming Menu>>Retrieve File)Status messages on the transfer are posted on the Management Sys-tem screen.NOTE: The new firmware image file that replaces the “Inactive Image” file will be automatically verified.6. Reboot the transceiver.Main Menu>>Maintenance Menu>>Reprogramming Menu>>Reboot Device7. Test the transceiver for normal operation.End of ProcedureError Messages During File TransfersIt is possible to encounter errors during a file transfer. In most cases errors can be quickly corrected by referring to Table 2-6.Table 2-6. Common Errors During TFTP Transfer Error Message Likely Cause/Corrective ActionInvalid File Type Indicates that the file is not a valid firmware file. Locate proper file and re-load.File not found Invalid or non-existent filename on TFTP serverInvalid file path Invalid or non-existent file path to TFTP serverTimeout TFTP transfer time expired. Increase the timeout value.Flash Error Flash memory error. Contact factory for assistance.
05-2806A01, Rev. H iNET Series Reference Manual 1052.9.2 Configuration Scripts MenuA configuration script file contains all of the settable parameters of a radio that are accessible through the menu interface, with a few excep-tions. A configuration script file is in plain text format and can be easily edited in a text program.Configuration scripts can be helpful in several ways. Three common uses for them are:• To save and restore known-good configuration files from your radios.• To facilitate the configuration of a large number of radios.• To provide troubleshooting information when you contact the factory for technical support.How Configuration Files WorkWhen a configuration script file is downloaded to a radio (Retrieve), the radio executes the parameters as commands and takes the values con-tained in it. When a configuration script file is uploaded from the radio (Send) it contains the current values of the parameters that the radio is configured with. Figure 2-66 below shows the Configuration Scripts Menu.Bad CRC Cyclic Redundancy Check reporting a corrupted file. Attempt to re-load, or use a different file.Version String Mismatch Invalid file detected. Attempt to re-load, or use a different file.Sending LCP Requests The PPP server is querying for any clients that may need to connect.Port not Enabled The serial port is disabled.Table 2-6. Common Errors During TFTP Transfer  (Continued)Error Message Likely Cause/Corrective Action
106 iNET Series Reference Manual 05-2806A01, Rev. HFigure 2-66. Configuration Scripts Menu•TFTP Host Address—IP address of the computer on which the TFTP server resides. [Any valid IP address]•Filename—Name of file containing this unit’s configuration pro-file that will be transferred to the TFTP server. The configura-tion information will be in a plain-text ASCII format.[Any 40-character alphanumeric string] May require a sub-direc-tory, for example: config\inet-config.txt. (See “Configuration Scripts Menu” on Page 105 for more information.)NOTE: The filename field is used to identify the desired incoming fileand as the name of the file being exported to the TFTP server.Before exporting a unit’s configuration, you may want to nameit in a way that reflects the radio’s services or other identifica-tion.•TFTP Timeout—Time in seconds the TFTP server will wait for a packet ACK (acknowledgment) from the transceiver before suspending the file transfer. [10 to 120 seconds; 10]•Retrieve File—Initiate the file transfer of the configuration file from TFTP server into the transceiver.•Send File—Initiate the file transfer from the transceiver’s current configuration file to TFTP server.NOTE: See “Upgrading the Firmware” on Page 102 for details onsetting up the TFTP server.Sample of Configuration Script FileA sample configuration script file is provided as part of every firmware release. The name of the file is followed by the revision number. For example, the sample file for firmware revision 2.1.0 is: inet2-config-2_1_0.txt.
05-2806A01, Rev. H iNET Series Reference Manual 107Editing Configuration FilesOnce a Remote unit’s operation is fine-tuned, use the Configuration Scripts Menu on Page 105 to save a copy of the configuration on a PC. Once the file is saved on the PC it can be used as a source to generate modified copies adjusted to match other devices. The configuration files can be modified using a text editor or an automated process. (These applications not provided by GE MDS).We recommend that you review and update the following parameters for each individual unit. Other parameters may also be changed as neces-sary. Each resulting file should be saved with a different name. We rec-ommend using directories and file names that reflect the location of the unit to facilitate later identification.Editing Rules • You may include only parameters you want to change from the default value.• Change only the parameter values.• Capitalization counts in some field parameters. (Example: System Mode)• Comment Fieldsa. Edit, or delete anything on each line to the right of the comment delineator, the semicolon (;).b. Comments can be of any length, but must be on the same line as the parameter, or on a new line that begins with a semicolon character.c. Comments after parameters in files exported from a trans-ceiver do not need to be present in your customized files.• Some fields are read-only. These are designated by “(RO)” in the configuration sample file.Table 2-7. Common User-Alterable Parameters Field Comment RangeIP Address Unique for each individual radio Any legal IP addressIP Gateway May change for different groups or locationsAny legal IP addressUnit Name Should reflect a specific device. This information will appear in Management System headings Any 20-character alphanumeric stringLocation Used only as reference for network administration Any 40-character alphanumeric string
108 iNET Series Reference Manual 05-2806A01, Rev. H2.9.3 Authorization Keys MenuFigure 2-67. Authorization Key Menu•Authorization Key—Initiate the entering of an Authorization Key into the transceiver’s non-volatile memory.•Authorized Features—List of authorized features available for use [enabled, disabled]. GE MDS iNET-II radios will show an additional selection called Encryption under Authorized Features.2.9.4 Change the Type of RemoteEnter the serial number of the unit to be changed in the Auth Key field to turn a Serial Gateway Remote into an Ethernet Bridge Remote, or vice-versa.2.9.5 Auto-Upgrade/Remote-Reboot MenuNOTE: This menu is only available when GE MDS NETview MS keyis enabled.
05-2806A01, Rev. H iNET Series Reference Manual 109Invisible place holderFigure 2-68. Auto-Upgrade / Remote Reboot Menu•Auto Upgrade—Causes all of the Remotes associated to this AP to read the AP’s newest firmware version (active or inactive) and upload it via TFTP to the inactive image, but only if it is newer than the Remote’s current firmware.•Reboot on Upgrade—Determines how a Remote will behave once it has uploaded new firmware from the AP as part of an auto-upgrade. When enabled, the Remote will reboot to the new firmware.•Force Reboot—Causes all of the Remotes associated to this AP to reboot immediately. They will reboot to their current active image—the same as if the power were re-cycled.NOTE: To use the Auto Upgrade/Reboot feature, both the AP andRemotes must already be running version 4.4.0 or newer firm-ware. Exception: If the AP has already been upgraded to version4.4.0 and the Remote is still at 3.5.0 or older, you can upgradethe Remote by using the AP as a file server. This methodallows for only one remote to be upgraded at a time. Instruc-tions for this method are given below.Firmware Upgrade (with AP Acting as a TFTP Server)An AP running firmware version 4.4.0 (or newer) may be used as a file server to upgrade Remotes running older firmware (3.5.0 or earlier). Follow the steps below to perform the upgrade:1. At the Reprogramming Menu (Page 101), Enter the AP’s IP Address in the TFTP Server field.2. Enter upgrade_from_ap.ipk in the Filename field.
110 iNET Series Reference Manual 05-2806A01, Rev. HNOTE: The filename is case sensitive.3. Perform the firmware download.2.9.6 Radio Test MenuUsing this menu, you can manually key the radio transmitter to make measurements of antenna performance. (See “Antenna Aiming” on Page 141 for details.)Figure 2-69. Radio Test MenuShown with Test Mode set to ONNOTE : Use of the Test Mode will disrupt traffic through the radio. Ifthe unit is an Access Point, it will disrupt traffic through theentire network.Test Mode function is automatically limited to 10 minutes andshould only be used for brief measurement of transmit power.It may also be manually reset to continue with the testing orturned off.•Test Mode—Controls access to the transceiver’s suite of tools. [ON, OFF; OFF]•Frequency—Set radio operating frequency during the testing period to a single frequency. [915.0000 MHz]•TX Output Power—Temporarily overrides the power level set-ting in the Radio Configuration Menu. [20]•TxKey—Manually key the radio transmitter for power mea-surements. [Enable, Disable; Disable]
05-2806A01, Rev. H iNET Series Reference Manual 111•RSSI—Incoming received signal strength on frequency entered in the frequency parameter on this screen (–dBm). This RSSI measurement is updated more frequently than the RSSI by Zone display of the Performance Information menu. Note that for the GE MDS iNET, the RSSI is an average of the RSSI samples. The RSSI value is reset every time the radio returns to scanning mode.2.9.7 Ping Utility MenuFigure 2-70. Ping Utility Menu•IP Addr—Address to send a PING. [Any valid IP address]•Count—Number of PING packets to be sent.•Packet Size—Size of each PING data packet (bytes).•Go—Send PING packets to address shown on screen.Screen will be replaced with detailed report of PING activity. Press any key after viewing the results to return to this menu.2.9.8 Reset to Factory DefaultsTo reset all transceiver parameters back to the factory defaults, including the password, you must enter a special code (authorization key) provided by the factory in place of the user name at the time of login. This procedure is useful when several parameters have been modified, and there is no track of changes. It causes the transceiver to return to a known state.Password ResetAs part of the reset action the transceiver’s password is reverted to the default value of admin. As a security measure, this event causes all radio parameters to return to the factory default settings, including zone skip-ping (as applicable), baud rate settings, network name, security phrase, etc.
112 iNET Series Reference Manual 05-2806A01, Rev. H
05-2806A01, Rev. H iNET Series Reference Manual 1133 TROUBLESHOOTING3 Chapter Counter Reset ParagraphContents3.1   Interpreting the Front Panel LEDs ........................................... 1153.2   Troubleshooting Using the Embedded Management System . 1163.2.1   Starting Information Screen  ...................................................... 1173.2.2   Packet Statistics Menu .............................................................. 1183.2.3   Serial Port Statistics Menu ........................................................ 1193.2.4   Diagnostic Tools  ........................................................................ 1193.3   Using Logged Operation Events.............................................. 1193.4   Alarm Conditions...................................................................... 1203.5   Correcting Alarm Conditions .................................................... 1213.6   Logged Events......................................................................... 123
114 iNET Series Reference Manual 05-2806A01, Rev. H
05-2806A01, Rev. H iNET Series Reference Manual 115Successful troubleshooting of a wireless system is not difficult, but requires a logical approach. It is best to begin troubleshooting at the Access Point unit, as the rest of the system depends on the Access Point for synchronization data. If the Access Point has problems, the operation of the entire wireless network will be affected.When communication problems are found, it is good practice to begin by checking the simple things. Applying basic troubleshooting tech-niques in a logical progression can identify many problems.Multiple Communication LayersIt is important to remember the operation of the network is built upon a radio communications link. On top of that are two data levels— wireless MAC, and the data layer. It is essential that the wireless aspect of the Access Point and the Remotes units to be associated are operating prop-erly before data-layer traffic will function.Unit Configuration There are over 50 user-configurable parameters in the Management System. Do not overlook the possibility that human error may be the cause of the problem. With so many possible parameters to look at and change, a parameter may be incorrectly set, and then what was changed is forgotten.To help avoid these problems, we recommend creating an archive of the transceiver’s profile when your installation is complete in a Configura-tion File. This file can be reloaded into the transceiver to restore the unit to the factory defaults or your unique profile. For details on creating and archiving Configuration Files, Configuration Scripts Menu on Page 105.Factory Assistance If problems cannot be resolved using the guidance provided here, review the GE MDS web site’s technical support area for recent soft-ware/firmware updates, general troubleshooting help, and service infor-mation. Additional help is available through our Technical Services Department. (See “TECHNICAL ASSISTANCE” on the inside of the rear cover.)3.1 Interpreting the Front Panel LEDsAn important set of troubleshooting tools are the LED status indicators on the front panel of case. You should check them first whenever a problem is suspected. Table 3-1 below provides suggestions for
116 iNET Series Reference Manual 05-2806A01, Rev. Hresolving common system difficulties using the LEDs, and Table 3-2 provides other simple techniques. 3.2 Troubleshooting Using the Embedded Management SystemIf you have reviewed and tried the things mentioned in Table 3-1 and still have not resolved the problem, there are some additional tools and techniques that can be used. The embedded Management System is a good source of information that may be used remotely to provide pre-liminary diagnostic information, or may even provide a path to cor-recting the problem.Table 3-1. Troubleshooting Using LEDs—Symptom-BasedSymptom Problem/Recommended System ChecksPWR LED does not turn ona. Voltage too low—Check for the proper supply voltage at the power connector. (10–30 Vdc)b. Indefinite Problem—Cycle the power and wait (≈ 30 seconds) for the unit to reboot. Then, recheck for normal operation.LINK LED does not turn ona. Network Name of Remote not identical to desired Access Point—Verify that the system has a unique Network Name. b. Not yet associated with an Access Point with the same Network Name.Check the “Status” of the unit’s process of associating with the Access Point. Use the Management System.c. Poor Antenna System—Check the antenna, feedline and connectors. Reflected power should be less than 10% of the forward power reading (SWR 2:1 or lower). PWR LED is blinkinga. Blinking indicates an alarm condition exists. b. View Current Alarms and Event Log and correct the problem if possible.(See “Using Logged Operation Events” on Page 120)c. Blinking will continue until the source of the alarm is corrected, for example, a valid IP address is entered, etc.LAN LED does not turn ona. Verify the Ethernet cable is connect at both ends.b. Verify that the appropriate type of Ethernet cable is used: straight-through, or crossover.LAN LED lights, but turns off after some timeVerify traffic in LAN. Typically, the radio should not be placed in high traffic enterprise LANs, as the it will not be able to pass this level of traffic. If needed, use routers to filter traffic.
05-2806A01, Rev. H iNET Series Reference Manual 117Table 3-2. Basic Troubleshooting Using the Management System Symptom Problem/Recommended System ChecksRemote does not associate; stays in HOPSYNCa. Verify the AP has sufficiently large number in the “Max Remotes” parameter of the Network Configuration Menu.b. Verify the correct MAC address is listed in the “Approved Remotes List” or “Approved Access Points List” of the Security Configuration menu.Serial data is slow with UDP multicast trafficChange Beacon Period to FAST. (Radio Configuration Menu)Cannot access the MS through COM1a. Connect to unit via Telnet or Web browserb. Disable the serial mode for COM1(Serial Gateway Configuration>>Com1 Serial Data Port>>Status>>Disabled)     or, if you know the unit’s data configuration:a. Connect to COM 1 via a terminal set to VT100 and the port’s data baud rate.b. Type +++c. Change the terminal’s baud rate to match the transceiver’s Console Baud Rate.d. Type +++Display on terminal/Telnet screen garbledVerify the terminal/terminal emulator or Telnet application is set to VT100Cannot pass IP data to WAN.a. Verify your IP settings.b. Use the PING command to test communication with the transceivers in the local radio system.c. If successful with local PING, attempt to PING an IP unit attached to a transceiver.d. If successful with the LAN PINGs, try connecting to a known unit in the WAN.Wireless Retries too high.Possible Radio Frequency Interference—a. If omnidirectional antennas are used, consider changing to directional antennas. This will often limit interference to and from other stations.b. Try skipping some zones where persistent interference is known or suspected.c. The installation of a filter in the antenna feedline may be necessary. Consult the factory for further assistance.Password forgotten.a. Connect to the transceiver using a terminal through the COM1 Port.b.  Obtain a password-resetting Authorization Key from your factory representative.c. Enter the Authorization Key at the login prompt as a password.Packet Repeat Mode troubles (extra characters in data, data not delivered)Verify that all radios in the network have their Packet Redundancy Mode set to the same selection (Single Packet vs. Packet Repeat Mode).
118 iNET Series Reference Manual 05-2806A01, Rev. HThe following is a summary of how several screens in the Management System can be used as diagnostic tools.3.2.1 Starting Information Screen(See Starting Information Screen on Page 32)The Management System’s “homepage” provides some valuable bits of data. One of the most important is the “Device Status” field. This item will tell you if the unit is showing signs of life. If the Device Status field says “associated,” then look in the network areas beginning with network data statistics. If it displays some other message, such as Scanning, Hop Sync or Alarmed, you will need to determine why it is in this state.The Scanning state indicates a Remote unit is looking for an Access Point beacon signal to lock onto. It should move to the Hop Sync and finally to the Associated state within less than a minute. If this Remote unit is not providing reliable service, look at the Event Logs for signs of lost association with the Access Point or low signal alarms. Table 3-3 provides a description of the Device Status messages.If the Remote is in an “Alarmed” state, the unit may still be operational and associated. Look for the association state in the Wireless Network Status screen to determine if the unit is associated. If it is, then look at the Error Log for possible clues.If the unit is in an “Alarmed” state and not able to associate with an Access Point unit, then there may be problem with the wireless network layer. Call in a radio technician to deal with wireless issues. Refer the technician to the RADIO (RF) MEASUREMENTS on Page 139 for information on antenna system checks.Table 3-3. Device Status1 1. Available in the Startup Information Screen or the Wireless Status Screen at the Remotes.Scanning The unit is looking for an Access Point beacon signal. If this is a Remote radio, Associated means that this unit is associated with an Access PointHop Sync The unit has found a valid beacon signal for its network and has changed its frequency hopping pattern to match that of the AP.Connected The unit has established a radio (RF) connection with the Access Point, but has not obtained cyber-security clearance to pass data.Associated This unit has successfully synchronized and is “associated” with an Access Point. This is the normal operating state.Alarmed The unit is has detected one or more alarms that have not been cleared.
05-2806A01, Rev. H iNET Series Reference Manual 1193.2.2 Packet Statistics Menu (See Packet Statistics Menu on Page 91)This screen provides detailed information on data exchanges between the unit being viewed and the network through the wireless and the Ethernet (data) layers. These include:The most significant fields are the Packets Dropped, Retries, Retry Errors, Receive Errors and Lost Carrier Detected. If the data values are more than 10% of their sent and received counterparts, or the Lost Car-rier Detected value is greater than a few dozen, there may be trouble with radio-frequency interference or a radio link of marginal strength. Review the RSSI by Zone Screen’s values (Page 87) for zones that are more than 2 dB (decibels) below the average level, and for signal level values that are likely to provide marginal service. For example, an average level is less than –85 dBm during normal conditions with a data rate of 256 kbps. If the RSSI levels in each zone are within a few dB of each other, but less than –85 dBm, then a check should be made of the aiming of the antenna system and for a satisfactory SWR. Refer to RADIO (RF) MEASUREMENTS on Page 139 for information on antenna system checks.NOTE: For a data rate of 512 kbps (1 Mbps for iNET-II), the averagesignal level should be –77 dBm or stronger with no interfer-ence.3.2.3 Serial Port Statistics Menu (See Serial Data Statistics Menu on Page 99)This screen provides top-level information on data exchanges between the unit’s serial ports and the network through the wireless and the Ethernet (data) layers. These include:You can use this screen as a indicator of port activity at the data and IP levels.Wireless Packet Statistics• Packets received • Packets dropped• Packets sent • Receive errors • Bytes received • Retries• Bytes sent • Retry errorsEthernet Packet Statistics• Packets received • Packets dropped• Packets sent • Receive errors• Bytes received • Retries• Bytes sent • Retry errors• Lost carrier detected
120 iNET Series Reference Manual 05-2806A01, Rev. H3.2.4 Diagnostic Tools(See MAINTENANCE on Page 99)The radio’s Maintenance menu contains two tools that are especially useful to network technicians—the Radio Test Menu and the Ping Utility. The Radio Test selection allows for testing RF operation, while the Ping Utility can be used to verify reachability to pieces of equipment connected to the radio network. This includes transceivers and user-sup-plied Ethernet devices.3.3 Using Logged Operation Events(See Event Log Menu on Page 88)The transceiver’s microprocessor monitors many operational parame-ters and logs them as various classes of “events”. If the event is one that affects performance, it is an “alarmed”. There are also normal or routine events such as those marking the rebooting of the system, implementa-tion of parameter changes and external access to the Management System. Informational events are stored in temporary (RAM) memory that will be lost in the absence of primary power, and Alarms will be stored in permanent memory (Flash memory) until cleared by user request. Table 2-5 summarizes these classifications. These various events are stored in the transceiver’s “Event Log” and can be a valuable aid in troubleshooting unit problems or detecting attempts at breaching network security.3.4 Alarm Conditions(See View Current Alarms on Page 90)Most events, classified as “critical” will make the PWR LED blink, and will inhibit normal operation of the transceiver. The LED blinks until the corrective action is completed.• Bytes In On Port xxx • Bytes In On Socket xxx• Bytes Out On Port xxx • Bytes Out On Socket xxxTable 3-4. Event ClassificationsLevel Description/Impact StorageInformational Normal operating activities Flash MemoryMinor Does not affect unit operation RAMMajor Degraded unit performance but still capable of operationRAMCritical Prevents the unit from operating RAM
05-2806A01, Rev. H iNET Series Reference Manual 121Table 3-5. Alarm Conditions (Alphabetical Order) Alarm Condition Reported Event Log Entry SNMP TrapEVENT_50_LIMIT Crossed 50% of Eth Port Rate LimitrateLimit50(20)EVENT_75_LIMIT Crossed 75% of Eth Port Rate LimitrateLimit75(21)EVENT_100_LIMIT Crossed 100% of Eth Port Rate LimitrateLimit100(22)EVENT_ADC ADC output Railed adcInput(3)EVENT_AP_NN_CHANGED Network Name changed at the APapNetNameChanged(74)EVENT_BRIDGE Network Interface /Error networkInterface(17)EVENT_NO_CHAN_CNT Mismatch in Channel count at AP/REMChanCnt(71)EVENT_NO_CHAN Using Channel hopping but no channels selectedNoChan(23)EVENT_COMPRESS Compression setting changedcompressionChanged(76)EVENT_ENDPOINT Endpoint Added/Removed (AP only)eventEndpoint(67)EVENT_ETH_LINK_AP* AP Ethernet Link DisconnectedapEthLinkLost(19)EVENT_FLASH_TEST Flash Test Failed -EVENT_FPGA FPGA communication FailedfpgaCommunication(2)EVENT_FREQ_CAL Frequency Not CalibratedfrequencyCal(7)EVENT_INIT_ERR Initialization Error initializationError(18)EVENT_IPADDR*IP Address Invalid ipAddressNotSet(4)EVENT_IP_CONN(OK) ipConnectivityOK(75)EVENT_IPMASK*IP Mask Invalid ipNetmaskNotSet(5)EVENT_LAN_PORT lanPortStatus(78)EVENT_MAC MAC communication FailedmacCommunication(1)EVENT_MACADDR MAC Address Invalid noMacAddress(6)EVENT_NETNAME*Netname Invalid invalidNetname(12)EVENT_PLL_LOCK PLL Not locked pllLock(10)EVENT_POWER_CAL Power Calibrated/Not CalibratedpowerCal(8)EVENT_POWER_HIGH RF Power Control Saturated HighrfPowerHigh(13)EVENT_POWER_LOW RF Power Control Saturated LowrfPowerLow(14)
122 iNET Series Reference Manual 05-2806A01, Rev. H* Condition may be corrected by user and alarm cleared.3.5 Correcting Alarm Conditions(See View Event Log on Page 91)Table 3-6 provides insight on the causes of events that inhibit the unit from operating, and possible corrective actions. The Event Description column appears on the Event Log screen.EVENT_REMOTE Remote Added/ Removed (AP only)eventRemote(66)EVENT_REPETITIVE The previous event is occurring repetitivelyEVENT_ROUTE_ADD Manual entry added to Routing tablerouteAdded(68)EVENT_ROUTE_DEL Manual entry deleted from Routing tablerouteDeleted(69)EVENT_RSSI*RSSI Exceeds thresholdrssi(11)EVENT_RSSI_CAL RSSI Not Calibrated rssiCal(9)EVENT_SDB_ERR Internal Remote/Endpoint database error (AP only)sdbError(80)EVENT_SINREM_SWITCH Eth/Serial mode switch in a Single RemotesinRemSwitch(70)EVENT_SYSTEM_ERROR* System Error Cleared; Please RebootsystemError(16)EVENT_TFTP_CONN TFTP connectivity achievedtftpConnection(73)EVENT_TFTP_ERR Attempted TFTP connection failedtftpConnFailed(79)Table 3-5. Alarm Conditions (Alphabetical Order)  (Continued)Alarm Condition Reported Event Log Entry SNMP TrapTable 3-6. Correcting Alarm Conditions—Alphabetical Order Event Log Entry Generating Condition Clearing Condition or ActionADC Failure The ADC always reads the same value (either high or low limit)Contact factory Technical Services for assistanceAP Ethernet Link Monitor will check state of Ethernet link and set alarm if it finds the link downEthernet link is re-establishedBridge Down When the Bridge fails to be initializedContact factory Technical Services for assistanceFlash Test Failed Internal check indicates corruption of Flash memoryContact factory Technical Services for assistanceFPGA Failure Communication lost to the FPGAContact factory Technical Services for assistance
05-2806A01, Rev. H iNET Series Reference Manual 1233.6 Logged Events(See View Event Log on Page 91)The following events allow the transceiver to continue operation and do not make the PWR LED blink. Each is reported through an SNMP trap. The left hand column, “Event Log Entry” is what will be shown in the Event Log.General System ErrorInternal checks suggest unit is not functioning properlyReboot the transceiverInitialization Error Unit fails to complete boot cycleContact factory Technical Services for assistanceInvalid IP Address The IP address is either 0.0.0.0 or 127.0.0.1Program IP address to something other than 0.0.0.0 or 127.0.0.1MAC Failure The monitor task reads the LinkStatus from the MAC every second. If the MAC does not reply 10 consecutive times (regardless of what the result is) the CPU assumes the transceiver has lost communication to the MAC.Contact factory Technical Services for assistanceNetwork Interface ErrorUnit does not recognize the LAN interfaceContact factory Technical Services for assistanceNetwork Name Not ProgrammedNetwork name is “Not Programmed”Change Network Name to something other than “Not Programmed”PLL Out-of-Lock The FPGA reports a synthesizer out-of-lock condition when monitored by the CPU.Contact factory Technical Services for assistance.Power Control Railed HighPower control can no longer compensate and reaches the high railContact factory Technical Services for assistancePower Control Railed LowPower control can no longer compensate and reaches the low railContact factory Technical Services for assistanceRSSI Exceeds ThresholdThe running-average RSSI level is weaker (more negative) than the user-defined value.Check aiming of the directional antenna used at the Remote; or raise the threshold level to a stronger (less-negative) value.Table 3-6. Correcting Alarm Conditions—Alphabetical Order  Event Log Entry Generating Condition Clearing Condition or Action
124 iNET Series Reference Manual 05-2806A01, Rev. HTable 3-7. Non-Critical Events—Alphabetical Order Event Log Entry Severity DescriptionAssociation Attempt Success/FailedMAJOR Self explanatoryAssociation Lost - AP Hop Parameter ChangedMINOR Self explanatoryAssociation Lost - AP's Ethernet Link DownMAJOR Self explanatoryAssociation Lost - Local IP Address ChangedMAJOR Self explanatoryAssociation Lost - Local Network Name ChangedMAJOR Self explanatoryAssociation Lost/Established MAJOR Self explanatoryAuth Demo Mode Expired -- Rebooted Radio/EnabledMAJOR Self explanatoryAuth Key Entered - Key Valid/Key InvalidMAJOR Self explanatoryBit Error Rate Below threshold/Above thresholdINFORMATIONAL Self explanatoryConsole Access Locked for 5 MinMAJOR Self explanatoryConsole User Logged Out/Logged InMAJOR Self explanatoryCountry/SkipZone Mismatch INFORMATIONAL Self explanatoryCurrent AP No Longer ApprovedMAJOR May occur during the Scanning process at a remote. Indicates that the received beacon came from an AP which is not in the “Approved AP” list. This may be caused by some remotes hearing multiple AP's. This event is expected behavior.MAC Decryption Failed/MAC Decryption OKA decryption error is logged when an encryption phrase mismatch has occurred. A mismatch is declared after five consecutive errors over a 40-second window. When the error has cleared, MAC DECRYPT OK will appear.Desired AP IP Addr Mismatch INFORMATIONAL Self explanatoryETH Rate Indicates heavy bursts of traffic on the unit's Ethernet port (LAN). This is expected behavior, resulting from the network configuration.Ethernet Port Enabled/DisabledINFORMATIONAL Self explanatoryExpected Sync Lost/EstablishedINFORMATIONAL Self explanatoryHop Sync Lost/Established INFORMATIONAL Self explanatoryHop Table Generated/Generation FailedINFORMATIONAL Self explanatoryHTTP Access Locked for 5 Min MAJOR Self explanatory
05-2806A01, Rev. H iNET Series Reference Manual 125HTTP User Logged Out/Logged InMAJOR httpLogin(49)Log Cleared INFORMATIONAL Self explanatoryMAC Param Changed Caused by remotes running in auto data rate mode. Every time the link conditions cause a data rate change, the remote’s MAC changes to the new rate and forwards a signal to the AP. This indicates link quality is changing and causing the data rate to adjust accordingly.Max Beacon Wait Time ExceededMAJOR Self explanatoryReceived Beacon - AP is BlacklistedINFORMATIONAL Self explanatoryReceived Beacon - Netname Does Not MatchINFORMATIONAL Self explanatoryReceived Beacon - Valid/ErroredINFORMATIONAL Self explanatoryRem Ethernet Link Connected/DisconnectedMAJOR Self explanatoryReprogramming Complete INFORMATIONAL Self explanatoryReprogramming Failed MAJOR Self explanatoryReprogramming Started INFORMATIONAL Self explanatoryScanning Started INFORMATIONAL Self explanatorySNR Within threshold/Below thresholdINFORMATIONAL Self explanatorySystem Bootup (power on) INFORMATIONAL Self explanatoryTelnet Access Locked for 5 MinMAJOR Self explanatoryTelnet User Logged Out/Logged InMAJOR Self explanatoryUser Selected Reboot MAJOR Self explanatoryTable 3-7. Non-Critical Events—Alphabetical Order  (Continued)Event Log Entry Severity Description
126 iNET Series Reference Manual 05-2806A01, Rev. H
05-2806A01, Rev. H iNET Series Reference Manual 1274PLANNING A RADIO       NETWORK4 Chapter Counter Reset ParagraphContents4.1   INSTALLATION PLANNING .................................................... 1294.1.1   General Requirements ..............................................................129DIN Rail Mounting Option............................................................... 1314.1.2   Site Selection  ............................................................................1314.1.3   Terrain and Signal Strength .......................................................1324.1.4   Antenna & Feedline Selection  ................................................... 1324.1.5   How Much Output Power Can be Used?  ..................................1354.1.6   Conducting a Site Survey  .........................................................1364.1.7   A Word About Radio Interference ..............................................1364.1.8   Notes on Using 28 VDC Power Supplies ..................................1384.2   RADIO (RF) MEASUREMENTS.............................................. 1394.2.1   Antenna System SWR and Transmitter Power Output  .............140Introduction..................................................................................... 140Procedure .......................................................................................1404.2.2   Antenna Aiming  .........................................................................141Introduction..................................................................................... 141Procedure .......................................................................................1414.3   dBm-WATTS-VOLTS CONVERSION CHART......................... 1434.4   PERFORMANCE NOTES ....................................................... 1444.4.1   Wireless Bridge .........................................................................1444.4.2   Distance-Throughput Relationship ............................................1444.4.3   Data LatencyTCP versus UDP Mode  ....................................1454.4.4   Data Compression  ....................................................................1454.4.5   Packets-per-Second (PPS) .......................................................1454.4.6   Station-to-Station Traffic ............................................................ 1454.4.7   Interference has a Direct Correlation to Throughput ................. 1454.4.8   Maximizing Throughput .............................................................1464.4.9   Placing an iNET Radio Behind a Firewall  ................................. 1474.5   SNMPv3 NOTES ..................................................................... 1474.5.1   Overview  ...................................................................................147SNMPv3 Accounts..........................................................................148Context Names...............................................................................148Password-Mode Management Changes ........................................149
128 iNET Series Reference Manual 05-2806A01, Rev. H
05-2806A01, Rev. H iNET Series Reference Manual 1294.1 INSTALLATION PLANNINGThis section provides tips for selecting an appropriate site, choosing an antenna system, and reducing the chance of harmful interference.4.1.1 General RequirementsThere are three main requirements for installing a transceiver—ade-quate and stable primary power, a good antenna system, and the correct interface between the transceiver and the data device. Figure 4-1 shows a typical Remote Gateway installation.NOTE: The iNET network port supports 10BaseT connections, butdoes not support 100BaseT connections. This should notpresent a problem because most hubs/switches auto-switchbetween 10BaseT and 100BaseT connections. Confirm thatyour hub/switch is capable of auto-switching data rates.To prevent Ethernet traffic from degrading iNET performance,place the iNET in a segment, or behind routers.Invisible place holderFigure 4-1. Typical Installation with a Tower-Mounted Antenna(Connect user data equipment to any compatible LAN or COM Port)Unit DimensionsFigure 4-2 shows the dimensions of the transceiver case and its mounting holes, and Figure 4-3 on Page 131, the dimensions for mounting with factory-supplied brackets. If possible, choose a mounting POWER SUPPLY13.8 VDC @ 580 mA (Max.)(10.5–30 Vdc) Negative Ground OnlyCOMPUTERW/TERMINALEMULATORTRANSCEIVERLOW-LOSS FEEDLINEANTENNASYSTEMDATA TERMINALEQUIPMENT ORLAN/WANNetwork
130 iNET Series Reference Manual 05-2806A01, Rev. Hlocation that provides easy access to the connectors on the end of the radio and an unobstructed view of the LED status indicators.Figure 4-2. Transceiver Dimensions4.25˝ (10.8 cm)4.75˝ (12.0 cm)1.4˝ (3.56 cm)6.75˝ (17.15 cm)4.5˝ (11.43 cm)TOPSIDEBOTTOM2.5˝ (6.35 cm)4.85˝ (12.32 cm)THREADEDHOLES FORMOUNTINGSCREWS (4)#6-32 X 1/4˝ LONGNot to scaleFRONT
05-2806A01, Rev. H iNET Series Reference Manual 131Invisible place holderInvisible place holder.Figure 4-3. Mounting Bracket DimensionsDIN Rail Mounting OptionThe unit may also be mounted with an optional 35mm DIN Rail Mounting Bracket (Part No. 03-4022A02). Equipment cabinets and racks of recent design often employ this type of mounting. Once the DIN bracket is mounted to the iNET case, it allows for quick installation and removal of the radio without the need for tools of any kind. Figure 4-4 shows how the DIN Rail bracket attaches to the back of the unit’s case, and how the entire unit attaches to the mounting rail.Invisible place holderFigure 4-4. DIN Rail Mounting of GE MDS Equipment4.1.2 Site SelectionSuitable sites should provide:• Protection from direct weather exposure• A source of adequate and stable primary power2.75˝ (7 cm)7.25˝ (18.4 cm)Step 1: Attach the bracket using the Step 2: Snap the assembly onto theDIN Rail. Removal is performed bythe two screws provided. (Attach to pulling down on the release tab.the end opposite the connectors.)Release Tab
132 iNET Series Reference Manual 05-2806A01, Rev. H• Suitable entrances for antenna, interface or other required cabling• Antenna location that provides as unobstructed a transmission path as possible in the direction of the associated station(s)These requirements can be quickly determined in most cases. A possible exception is the last item—verifying that an unobstructed transmission path exists. Radio signals travel primarily by line-of-sight, and obstruc-tions between the sending and receiving stations will affect system per-formance. If you are not familiar with the effects of terrain and other obstructions on radio transmission, the discussion below will provide helpful background.4.1.3 Terrain and Signal StrengthWhile the license-free 900 MHz band offers many advantages for data transmission services, signal propagation is affected by attenuation from obstructions such as terrain, foliage or buildings in the transmission path.A line-of-sight transmission path between the central transceiver and its associated remote site(s) is highly desirable and provides the most reli-able communications link. Much depends on the minimum signal strength that can be tolerated in a given system. Although the exact figure will differ from one system to another, a Received Signal Strength Indication (RSSI) of –77 dBm (–80 dBm for iNET-II) or stronger will provide acceptable performance in many systems. While the equipment will work at lower-strength signals, signals stronger than – 77 dBm provide a “fade margin” of 15 dB to account for variations in signal strength that may occur from time-to-time. RSSI can be measured with a terminal connected to the COM1 Port or with a HTTP browser to the LAN (Ethernet) connector. (See “Antenna Aiming” on Page 141 for details.)4.1.4 Antenna & Feedline SelectionNOTE: The transceiver is a Professional Installation radio system andmust be installed by trained professional installers, or factorytrained technicians. This text that follows is designed to aid the professionalinstaller in the proper methods of maintaining compliance withFCC Part 15 limits and the +36 dBm or 4 watts peak E.I.R.Plimit.AntennasThe equipment can be used with a number of antennas. The exact style used depends on the physical size and layout of a system. Contact your
05-2806A01, Rev. H iNET Series Reference Manual 133factory representative for specific recommendations on antenna types and hardware sources.In general, an omnidirectional antenna (Figure 4-5) is used at the Access Point station site. This provides equal coverage to all of the Remote Gateway sites.NOTE: Antenna polarization is important. If the wrong polarization isused, a signal reduction of 20 dB or more will result. Mostsystems using a gain-type omnidirectional antenna at theAccess Point station employ vertical polarization of the signal;therefore, the remote antenna(s) must also be vertically polar-ized (elements oriented perpendicular to the horizon).When required, horizontally polarized omnidirectionalantennas are also available. Contact your factory representa-tive for details.Invisible place holderFigure 4-5. Typical Omnidirectional AntennasAt Remote Gateway sites and units in point-to-point LANs, a directional Yagi (Figure 4-6) antenna is generally recommended to minimize inter-ference to and from other users. Antennas are available from a number of manufacturers.High-gain TypeUnity-gain Type
134 iNET Series Reference Manual 05-2806A01, Rev. HInvisible place holderFigure 4-6. Typical Yagi Antenna (mounted to mast)FeedlinesThe choice of feedline used with the antenna should be carefully consid-ered. Poor-quality coaxial cables should be avoided, as they will degrade system performance for both transmission and reception. The cable should be kept as short as possible to minimize signal loss.For cable runs of less than 20 feet (6 meters), or for short range trans-mission, an inexpensive type such as Type RG-8A/U may be acceptable. Otherwise, we recommend using a low-loss cable type suited for 900 MHz, such as Heliax®.Table 4-1 lists several types of popular feedlines and indicates the signal losses (in dB) that result when using various lengths of cable at 900 MHz. The choice of cable will depend on the required length, cost considerations, and the amount of signal loss that can be tolerated. The tables below outline the minimum lengths of RG-214 coaxial cable that must be used with common GE MDS omnidirectional antennas in order to maintain compliance with FCC maximum limit of +36 dBi. If other coaxial cable is used, the appropriate changes in loss figures must be made.Table 4-1. Length vs. Loss in Coaxial Cables at 900 MHz Cable Type10 Feet(3.05 m)50 Feet(15.24 m)100 Feet(30.48 m)500 Feet(152.4 m)RG-214 .76 dB 3.8 dB 7.6 dB Unacceptable LossLMR-400 0.39 dB 1.95 dB 3.90 dB Unacceptable Loss1/2 inch HELIAX 0.23 dB 1.15 dB 2.29 dB 11.45 dB7/8 inch HELIAX 0.13 dB 0.64 dB 1.28 dB 6.40 dB1-1/4 inch HELIAX 0.10 dB 0.48 dB 0.95 dB 4.75 dB1-5/8 inch HELIAX 0.08 dB 0.40 dB 0.80 dB 4.00 dB
05-2806A01, Rev. H iNET Series Reference Manual 135NOTE: The authority to operate the transceiver in the USA may bevoid if antennas other than those approved by the FCC areused. Contact your GE MDS representative for additionalantenna information.*Refer to Table 4-3 for allowable power settings of the transceiver for each antenna type.NOTE: There is no minimum feedline length required when a 6 dBigain or less antenna is used, as the EIRP will never exceed 36dBm which is the maximum allowed, per FCC rules. Thetransceiver’s RF output power may only be adjusted by themanufacturer or its sub-contracted Professional Installer.The GE MDS iNET-II Transceiver is factory set to +29 dBmpower output to maintain compliance with the FCC’s DigitalTransmission System (DTS) Part 15 rules. These rules limitpower to a maximum of 8 dBm/3 kHz, thus the iNET-II Trans-ceiver is factory set to +29 dBm. When calculating maximumtransceiver power output for iNET-II installations, use +29dBm if antenna gain is 6 dBi or less. See How Much OutputPower Can be Used? on Page 135 for power control of highergain antennas.4.1.5 How Much Output Power Can be Used?The transceiver is normally supplied from the factory set for a nominal +30 dBm (+29 dBm for iNET-II) RF power output setting; this is the maximum transmitter output power allowed under FCC rules. The power must be decreased from this level if the antenna system gain exceeds 6 dBi. The allowable level is dependent on the antenna gain, feedline loss, and the transmitter output power setting.NOTE: In some countries, the maximum allowable RF output may belimited to less than the figures referenced here. Be sure tocheck for and comply with the requirements for your area.Table 4-2. Feedline Length vs. Antenna Gain*(Required for Regulatory compliance)Antenna Gain (dBd)Antenna Gain (dBi)Minimum Feedline Length (Loss in dB)EIRP Level @ Min. LengthMaxrad Antenna Part No.Unity (0 dB) 2.15 dBi No minimum length +32.15 dBm Omni #MFB9003 dBd 5.15 dBi No minimum length +35.15 dBm Omni # MFB9005 dBd 7.15 dBi 3.1 meters (1.2 dB) +35.95 dBm Omni # MFB9006 dBd 8.15 dBi 9.1 meters (2.2 dB) +35.95 dBm Yagi # BMOY89039.2 dBd 11.34 dBi 25 meters (5.34 dB) +36.00 dBm Yagi OGB9-915
136 iNET Series Reference Manual 05-2806A01, Rev. H4.1.6 Conducting a Site SurveyIf you are in doubt about the suitability of the radio sites in your system, it is best to evaluate them before a permanent installation is underway. This can be done with an on-the-air test (preferred method); or indi-rectly, using path-study software.An on-the-air test is preferred because it allows you to see firsthand the factors involved at an installation site and to directly observe the quality of system operation. Even if a computer path study was conducted ear-lier, this test should be done to verify the predicted results.The test can be performed by first installing a radio and antenna at the proposed Access Point (AP) station site (one-per-system). Then visit the Remote site(s) with another transceiver (programmed as a remote) and a hand-held antenna. (A PC with a network adapter can be connected to each radio in the network to simulate data during this test using the PING command.)With the hand-held antenna positioned near the proposed mounting spot, a technician can check for synchronization with the Access Point station (shown by a lit LINK LED on the front panel) and measure the reported RSSI value. (See “Antenna Aiming” on Page 141 for details.) If adequate signal strength cannot be obtained, it may be necessary to mount the station antennas higher, use higher gain antennas, select a dif-ferent site or consider installing a repeater station. To prepare the equip-ment for an on-the-air test, follow the general installation procedures given in this guide and become familiar with the operating instructions found in the CHAPTER-2 EMBEDDED  MANAGEMENT SYSTEM  section Page 19.4.1.7 A Word About Radio InterferenceThe transceiver shares the radio-frequency spectrum with other 900 MHz services and other Part 15 (unlicensed) devices in the USA. As such, near 100% error-free communications may not be achieved in a given location, and some level of interference should be expected. How-ever, the radio’s flexible design and hopping techniques should allow adequate performance as long as care is taken in choosing station loca-tion, configuration of radio parameters and software/protocol tech-niques.In general, keep the following points in mind when setting up your com-munications network.• Systems installed in rural areas are least likely to encounter interfer-ence; those in suburban and urban environments are more likely to be affected by other devices operating in the license-free frequency band and by adjacent licensed services.• Use a directional antenna at remote sites whenever possible.
05-2806A01, Rev. H iNET Series Reference Manual 137Although these antennas may be more costly than omnidirectional types, they confine the transmission and reception pattern to a com-paratively narrow lobe, that minimizes interference to (and from) stations located outside the pattern.• If interference is suspected from a nearby licensed system (such as a paging transmitter), it may be helpful to use horizontal polarization of all antennas in the network. Because most other services use ver-tical polarization in this band, an additional 20 dB of attenuation to interference can be achieved by using horizontal polarization. Another approach is to use a bandpass filter to attenuate all signals outside the 900 MHz band.• Multiple Access Point units can co-exist in proximity to each other with only very minor interference. Each network name has a differ-ent hop pattern. (See “Protected Network Operation using Multiple Access Points” on Page 14.) Additional isolation can be achieved by using separate directional antennas with as much vertical or horizon-tal separation as is practical. • If constant interference is present in a particular frequency zone (collection of 8 RF channels), it may be necessary to “skip” that zone from the radio’s hopping pattern. The radio includes built-in software to help users identify and remove blocked frequency zones from its hopping pattern. See Page 55 for more information on Skip Zones. • If interference problems persist even after skipping some zones, try reducing the length of data streams. Groups of short data streams have a better chance of getting through in the presence of interfer-ence than do long streams.• The power output of all radios in a system should be set for the low-est level necessary for reliable communications. This lessens the chance of causing unnecessary interference to nearby systems.If you are not familiar with these interference-control techniques, con-tact your factory representative for more information.Calculating System GainTo determine the maximum allowable power setting of the radio, per-form the following steps:1. Determine the antenna system gain by subtracting the feedline loss (in dB) from the antenna gain (in dBi). For example, if the antenna gain is 9.5 dBi, and the feedline loss is 1.5 dB, the antenna system gain would be 8 dB. (If the antenna system gain is 6 dB or less, no power adjustment is required.)
138 iNET Series Reference Manual 05-2806A01, Rev. H2. Subtract the antenna system gain from 36 dBm (the maximum allowable EIRP). The result indicates the maximum transmitter power (in dBm) allowed under the rules. In the example above, this is 28 dBm.3. If the maximum transmitter power allowed is less than 30 dBm, set the power to the desired level using the Management System.(Main Menu>>Radio Configuration>>RF Output Power Setpoint)For convenience, Table 4-3 lists several antenna system gains and shows the maximum allowable power setting of the radio. Note that a gain of 6 dB or less entitles you to operate the radio at full power output –30 dBm (28.7 dBm for iNET-II).* Most antenna manufacturers rate antenna gain in dBd in their litera-ture. To convert to dBi, add 2.15 dB.† Feedline loss varies by cable type and length. To determine the loss for common lengths of feedline, see Table 4-1 on Page 134.For assistance in the conversion of dBm to Watts, see dBm-WATTS-VOLTS CONVERSION CHART on Page 143.4.1.8 Notes on Using 28 VDC Power SuppliesCommon 28 Vdc supplies are often high-current power supplies designed primarily to charge battery banks. The radio can be operated from these supplies, providing there are no transients on the leads as power is applied to the radio. Transients can be created that rise above 30 Vdc to a voltage that exceeds the primary voltage rating of the radio and can destroy its voltage regulators and other components. It is impor-tant to keep this potential hazard in mind when designing 28 Vdc power supply connections for the radio.• Use a two-conductor cable to power to the radio. Then the cur-rents in the positive and negative wires are equal and opposite, causing their magnetic fields to cancel. The result is no net inductance in the connection to cause voltage overshoot.• Do not connect a radio to a power supply that is already pow-ered up, unless necessary (that is, when connecting a radio to a battery bank and charger). When power is applied by switching on a power supply, the rise time of the supply is too slow to cause overshoot.Table 4-3. Antenna System Gain vs. Power Output SettingAntenna System Gain(Antenna Gain in dBi*minus Feedline Loss in dB†)Maximum Power Setting (PWR command)iNET RadioMaximum Power Setting (PWR command)iNET-II RadioEIRP(in dBm)Omni 6 (or less) 30 28 36Omni 11.14 24 23 36
05-2806A01, Rev. H iNET Series Reference Manual 139• Typically, there are multiple return paths for the negative side of the power supply, through the coaxial cable shield and the chassis, for example. Any imbalance in the currents in the power cable results in voltage overshoot, so this should be min-imized during initial power-up if the supply cannot be turned off.• Add a 1 to 2 Ω, 2 Watt resistor in series with the positive lead. This greatly limits voltage overshoot. Since these radios draw very little current in receive mode, and transmit only briefly, there is little loss in power efficiency. In transmit, the voltage drop is minimal and has no effect.• Minimize the length of the power cabling, within reason.• When power is applied from a power source having a relatively high (1 or 2 Ω) source impedance, or from a power source with-out a large amount of output capacitance, no overshoot occurs. Therefore, use a power supply that is rated appropriately for the radio if possible—avoid using power supplies that far exceed the radio's current requirements.Please direct any questions you may have about interfacing to GE MDS radios to the Technical Services Department via e-mail or telephone:E-mail: TechSupport@GEmds.comTel. +1-585-241-5510.4.2 RADIO (RF) MEASUREMENTSThere are several measurements that are a good practice to perform during the initial installation. The will confirm proper operation of the unit and if they are recorded, serve as a benchmark in troubleshooting should difficulties appear in the future. These measurements are:• Transmitter Power Output• Antenna System SWR (Standing-Wave Ratio)• Antenna Direction OptimizationThese procedures may interrupt traffic through an established network and should only be performed by a skilled radio-technician in coopera-tion with the network manager.4.2.1 Antenna System SWR and Transmitter Power OutputIntroductionA proper impedance match between the transceiver and the antenna system is important. It ensures the maximum signal transfer between the radio and antenna. The impedance match can be checked indirectly by measuring the SWR (standing-wave ratio) of the antenna system. If the results are normal, record them for comparison for use during future routine preventative maintenance. Abnormal readings indicate a pos-
140 iNET Series Reference Manual 05-2806A01, Rev. Hsible trouble with the antenna or the transmission line that will need to be corrected.The SWR of the antenna system should be checked before the radio is put into regular service. For accurate readings, a wattmeter suited to 1000 MHz measurements is required. One unit meeting this criteria is the Bird Model 43™ directional wattmeter with a 5J element installed.The reflected power should be less than 10% of the forward power (≈2:1 SWR). Higher readings usually indicate problems with the antenna, feedline or coaxial connectors.If the reflected power is more than 10%, check the feedline, antenna and its connectors for damage.Record the current transmitter power output level, and then set it to 30 dBm for the duration of the test to provide an adequate signal level for the directional wattmeter.Procedure1. Place a directional wattmeter between the ANTENNA connector and the antenna system.2. Place the transceiver into the Radio Test Mode using the menu sequence below:(Main Menu>>Maintenance Menu>>Radio Test>>Test Mode>>Y>>ON)NOTE: The Test Mode has a 10-minute timer, after which it will returnthe radio to normal operation. The Radio Test Mode can beterminated manually by selecting OFF on the menu or tempo-rarily disconnecting the radio’s DC power.3. Set the transmit power to 30 dBm. (This setting does not affect the output level during normal operation—only during Test Mode.)(Main Menu>>Maintenance Menu>>Radio Test>>Test Mode>>Tx Power Out-put)4. Key the transmitter.(Main Menu>>Maintenance Menu>>Radio Test>>Test Mode>>TxKey>> Enable)Use the PC’s spacebar to key and unkey the transmitter ON and OFF. (Enable/Disable)5. Measure the forward and reflected power into the antenna system and calculate the SWR and power output level. The output should agree with the programmed value.(Main Menu>>Radio Configuration>>RF Power Output)
05-2806A01, Rev. H iNET Series Reference Manual 1416. Turn off Radio Test Mode at the Access Point and Remote.(Main Menu>>Maintenance Menu>>Radio Test>>Test Mode>>Disable)End of procedure4.2.2 Antenna AimingIntroductionThe radio network integrity depends, in a large part, on stable radio signal levels being received at each end of a data link. In general, signal levels stronger than –77 dBm (–80 dBm for iNET-II) providesthe basis for reliable communication that includes a 15 dB fade margin. As the distance between the Access Point and Remotes increases, the influence of terrain, foliage and man-made obstructions become more influential and the use of directional antennas at Remote locations becomes necessary. Directional antennas usually require some fine-tuning of their bearing to optimize the received signal strength. The transceiver has a built-in received signal strength indicator (RSSI) that can be used to tell you when the antenna is in a position that provides the optimum received signal.RSSI measurements and Wireless Packet Statistics are based on mul-tiple samples over a period of several seconds. The average of these measurements will be displayed by the Management System.The measurement and antenna alignment process will usually take 10 or more minutes at each radio unit.The path to the Management System menu item is shown in bold text below each step of the procedure.Procedure1. Verify the Remote transceiver is associated with an Access Point unit by observing the condition of the LINK LED (LINK LED = On or Blinking). This indicates that you have an adequate signal level for the measurements and it is safe to proceed.2. View and record the Wireless Packets Dropped and Received Error rates.(Main Menu>>Performance Information>>Packet Statistics>>Wireless Packet Statistics)This information will be used later.3. Clear the Wireless Packets Statistics history. (Main Menu>>Performance Information>>Packet Statistics>>Wireless Packet Statistics>>Clear Wireless Stats)\4. Read the RSSI level at the Remote.(Main Menu>>Performance Information>>RSSI by Zone)
142 iNET Series Reference Manual 05-2806A01, Rev. H5. Optimize RSSI (less negative is better) by slowly adjusting the direction of the antenna.Watch the RSSI indication for several seconds after making each adjustment so that the RSSI accurately reflects any change in the link signal strength.6. View the Wireless Packets Dropped and Received Error rates at the point of maximum RSSI level. They should be the same or lower than the previous reading.(Main Menu>>Performance Information>>Packet Statistics>>Wireless Packet Statistics)If the RSSI peak results in an increase in the Wireless Packets Dropped and Received Error, the antenna may be aimed at an undes-ired signal source. Try a different antenna orientation.End of procedure
05-2806A01, Rev. H iNET Series Reference Manual 1434.3 dBm-WATTS-VOLTS CONVERSION CHARTTable 4-4 is provided as a convenience for determining the equivalent voltage or wattage of an RF power expressed in dBm.Table 4-4. dBm-Watts-Volts conversion—for 50 ohm systemsdBm V Po+53 100.0 200W+50 70.7 100W+49 64.0 80W+48 58.0 64W+47 50.0 50W+46 44.5 40W+45 40.0 32W+44 32.5 25W+43 32.0 20W+42 28.0 16W+41 26.2 12.5W+40 22.5 10W+39 20.0 8W+38 18.0 6.4W+37 16.0 5W+36 14.1 4W+35 12.5 3.2W+34 11.5 2.5W+33 10.0 2W+32 9.0 1.6W+31 8.0 1.25W+30 7.10 1.0W+29 6.40 800mW+28 5.80 640mW+27 5.00 500mW+26 4.45 400mW+25 4.00 320mW+24 3.55 250mW+23 3.20 200mW+22 2.80 160mW+21 2.52 125mW+20 2.25 100mW+19 2.00 80mW+18 1.80 64mW+17 1.60 50mW+16 1.41 40mW+15 1.25 32mW+14 1.15 25mW+13 1.00 20mW+12 .90 16mW+11 .80 12.5mW+10 .71 10mW+9 .64 8mW+8 .58 6.4mW+7 .500 5mW+6 .445 4mW+5 .400 3.2mW+4 .355 2.5mW+3 .320 2.0mW+2 .280 1.6mW+1 .252 1.25mWdBm V Po0 .225 1.0mW-1 .200 .80mW-2 .180 .64mW-3 .160 .50mW-4 .141 .40mW-5 .125 .32mW-6 .115 .25mW-7 .100 .20mW-8 .090 .16mW-9 .080 .125mW-10 .071 .10mW-11 .064-12 .058-13 .050-14 .045-15 .040-16 .0355dBm mV Po-17 31.5-18 28.5-19 25.1-20 22.5 .01mW-21 20.0-22 17.9-23 15.9-24 14.1-25 12.8-26 11.5-27 10.0-28 8.9-29 8.0-30 7.1 .001mW-31 6.25-32 5.8-33 5.0-34 4.5-35 4.0-36 3.5-37 3.2-38 2.85-39 2.5-40 2.25 .1μW-41 2.0-42 1.8-43 1.6-44 1.4-45 1.25-46 1.18-47 1.00-48 0.90dBm mV Po-49 0.80-50 0.71 .01μW-51 0.64-52 0.57-53 0.50-54 0.45-55 0.40-56 0.351-57 0.32-58 0.286-59 0.251-60 0.225 .001μW-61 0.200-62 0.180-63 0.160-64 0.141dBm μVPo-65 128-66 115-67 100-68 90-69 80-70 71 .1nW-71 65-72 58-73 50-74 45-75 40-76 35-77 32-78 29-79 25-80 22.5 .01nW-81 20.0-82 18.0-83 16.0-84 11.1-85 12.9-86 11.5-87 10.0-88 9.0-89 8.0-90 7.1 .001nW-91 6.1-92 5.75-93 5.0-94 4.5-95 4.0-96 3.51-97 3.2dBm μVPo-98 2.9-99 2.51-100 2.25 .1pW-101 2.0-102 1.8-103 1.6-104 1.41-105 1.27-106 1.18dBm nV Po-107 1000-108 900-109 800-110 710 .01pW-111 640-112 580-113 500-114 450-115 400-116 355-117 325-118 285-119 251-120 225 .001pW-121 200-122 180-123 160-124 141-125 128-126 117-127 100-128 90-129 80 .1ƒW-130 71-131 61-132 58-133 50-134 45-135 40-136 35-137 33-138 29-139 25-140 23 .01ƒW
144 iNET Series Reference Manual 05-2806A01, Rev. H4.4 PERFORMANCE NOTESThe following is a list of points that are useful for understanding the per-formance of the radio in your installation.4.4.1 Wireless BridgeThe transceiver acts as a bridge. If any radio in your network is con-nected to a large LAN, such as may be found in a large office complex, there may be undesired multicast/broadcast traffic over the air. As a bridge, the radios transmit this type of frame.The radio goes through a listening and learning period at start-up before it will send any packets over either of its ports. This is about 10 seconds after the CPU’s operating system has finished its boot cycle.The bridge code in the transceiver operates and makes decisions about packet forwarding just like any other bridge. The bridge code builds a list of source MAC addresses that it has seen on each of its ports. There are a few general rules that are followed when a packet is received on any port:• If the destination address is a multicast or broadcast address, forward the packet to all remotes.• If the destination address is not known, forward the packet to all remotes. • If the destination address is known, forward the packet to the port that the destination is known to be on (usually the RF port).• The bridge code uses Spanning Tree Protocol (STP) to pre-vent loops from being created when connecting bridges in parallel. For example, connecting two remotes to the same wired LAN could create a loop if STP was not used. Every bridge running STP sends out Bridge Protocol Data Units (BPDUs) at regular intervals so that the spanning tree can be built and maintained. BPDUs are 60-byte multicast Ethernet frames.4.4.2 Distance-Throughput RelationshipDistance affects throughput. Because of timers and other components of the protocol, there is a practical distance limit of 30 miles (48 km) for reliable operation. After this, although data still flows, the throughput will begin to drop and latency will increase, due to additional retries between the radios. Packets may start to be dropped. Some applications may tolerate this; others may not. Repeater stations may be used to extend the range.
05-2806A01, Rev. H iNET Series Reference Manual 1454.4.3 Data Latency—TCP versus UDP ModeThe latency of data passing through a network will depend on user data message length, the overall level of traffic on the network, and the quality of the radio path.Under ideal conditions—low traffic and good RF signal path—the latency for units operating in the TCP mode, will typically be around 5 ms in each direction. However, when UDP multicast traffic is trans-ported, the outbound packet latency (from AP to remote) is dependent on the beacon period.UDP multicast packet latency can be minimized by setting the Beacon Period to Fast (52 ms). Changing beacon rate to Fast will result in an average latency of 31 ms, assuming outbound packets wait for a beacon transmission 50% of the time (26ms) plus the normal packet latency (5 ms).4.4.4 Data CompressionEnabling this option uses an LZO compression algorithm for over-the-air data. Varying levels of data reduction are achieved depending on the nature of the data. Text files are typically the most compressible, whereas binary files are the least compressible. On average, a 30% increase in throughput can be achieved with compres-sion enabled.Compression is used on data packets of 100 bytes or more, including Ethernet, IP, and TCP/UDP headers.4.4.5 Packets-per-Second (PPS)The iNET-II radio has a limit of approximately 140 PPS (70 PPS in iNET). Consider this restriction when planning your network, especially when smaller packets are expected to make up the majority of the traffic as is the case with VoIP (Voice over IP).4.4.6 Station-to-Station TrafficWhen sending frames from an endpoint connected to one transceiver to another endpoint with a different transceiver, the throughput will be halved at best. This is because all frames must go through the AP and thus are transmitted twice over the same radio system. Therefore, in the previous 100-byte UDP example, the number of over-the-air bytes will be 380 bytes (190 bytes x 2) if the frame has to go station-to-station.4.4.7 Interference has a Direct Correlation to ThroughputInterference could be caused by other radios at the same site, in nearby locations, or by high power transmitters such as paging systems.
146 iNET Series Reference Manual 05-2806A01, Rev. H4.4.8 Maximizing ThroughputHere are some suggestion on things to try that may maximize throughput:1. AP Only: Increment the Dwell Time to the maximum of 262.1 ms. This lowers the overhead since it will stay longer on a channel. The down side is that if a particular channel is interfered with it will take longer to hop to another channel.(Main Menu>>Radio Configuration>>Dwell Time)2. AP Only: Change the Beacon Period to Normal (508 ms). This will also reduce the overhead of beacons sent out. On the down side, association time may be a little longer.(Main Menu>>Radio Configuration>>Beacon Period)3. Change the Fragmentation Threshold to the maximum of 1600. Longer packets will be sent over the air reducing overhead. On the other hand, if a packet is corrupted it will take longer to be retransmitted.(Main Menu>>Radio Configuration>>Fragmentation Threshold)4. Increase the RTS Threshold to 1600. RTS mechanism is used to reserve a time slot if packets exceed this number. On the other hand, a hidden-node might interfere more often than if RTS was not used.(Main Menu>>Radio Configuration>>RTS Threshold)Decreasing the RTS Threshold, to the 100 to 200 range, may improve throughput on a busy network. It will add small packets, but reduce collisions (and resulting re-tries) of large packets.(Main Menu>>Radio Configuration>>RTS Threshold)5. Activate compression on the Radio Configuration Menu (Compres-sion enabled).6. Use the Performance Information Menu to check the packets received by zone. (Remotes Only: Main Menu>>Performance Information>>Packet Statistics>>Packets Received by Zone) Readings should be close in value. A significantly lower value (2% reduction) probably indicates interference. Performance can be improved by blocking the affected zones at the Access Point. (Main Menu>>Radio Configuration>>Skip Zone Option)7. Use the Performance Information Menu to check for errors, retries and dropped packets. Do the same with Ethernet traffic.With weak signals, interference, or hidden nodes, the optimal per-formance may be lower due to collisions and retries.
05-2806A01, Rev. H iNET Series Reference Manual 1474.4.9 Placing an iNET Radio Behind a FirewalliNET-II and iNET radios use the port numbers listed below. If you place the radio behind a firewall, make sure these port numbers are included in the allowed list:• SSH: 22 <- Management• TELNET: 23 <- Management• SMTP: 25 <- DF1• TFTP: 69 <- Reprogramming• HTTP: 80 <- Management• NTP: 123 <- Time server• SNMP: 161 <- Management• SNMP-TRAP: 162 <- Event management via traps• HTTPS: 443 <- Management• SYSLOG: 514 <- Event management via remote syslogserverThese well-known port numbers follow the recommendation of IANA. For more information, go to http://www.iana.org/assignments/port-numbers.4.5 SNMPv3 NOTES4.5.1 OverviewThe transceiver’s SNMP Agent supports SNMP version 3 (SNMPv3). The SNMPv3 protocol introduces Authentication (MD5/SHA-1), Encryption (DES), the USM User Table, and View-Based Access (Refer to RFC2574 for full details). The SNMP Agent has limited SNMPv3 support in the following areas:• Only MD5 Authentication is supported (no SHA-1). SNMPv3 provides support for MD5 and SHA-1. Currently, only MD5 Authentication is supported in the SNMP Agent.• Limited USM User Table Manipulation. The SNMP Agent starts with 5 default accounts. New accounts can be added (SNMPv3 adds new accounts by cloning existing ones), but they will be volatile (will not survive a power-cycle). New views cannot be configured on the SNMP Agent. Views will be inherited for new accounts from the account that was cloned.The SNMP Agent uses one password pair (Authentication / Pri-vacy) for all accounts. This means that when the passwords change for one user, they change for all users.
148 iNET Series Reference Manual 05-2806A01, Rev. HSNMPv3 AccountsThe following default accounts are available for the SNMP Agent:enc_mdsadmin—Read/write account using Authentication and Encryp-tionauth_mdsadmin—Read/write account using Authenticationenc_mdsviewer—Read only account using Authentication and Encryp-tionauth_mdsviewer—Read only account using Authenticationdef_mdsviewer—Read only account with no Authentication or Encryp-tionContext NamesThe following Context Names are used (please refer to RFC2574 for full details):Admin accounts: context_a / Viewer accounts: context_vAll accounts share the same default passwords:Authentication default password: MDSAuthPwd / Privacy default pass-word: MDSPrivPwdPasswords can be changed either locally (via the console) or from an SNMP Manager, depending on how the Agent is configured. If pass-words are configured and managed locally, they are non-volatile and will survive a power-cycle. If passwords are configured from an SNMP manager, they will be reset to whatever has been stored for local man-agement on power-cycle.This behavior was chosen based on RFC specifications. The SNMP Manager and Agent don’t exchange passwords, but actually exchange keys based on passwords. If the Manager changes the Agent’s password the Agent doesn’t know the new password; just the new key. In this case, only the Manager knows the new password. This could cause problems if the Manager loses the password. If that happens, the Agent becomes unmanageable. Resetting the Agent’s passwords (and therefore keys) to what is stored in flash memory upon power-cycle prevents the serious problem of losing the Agent’s passwords.If passwords are managed locally, they can be changed on the Agent (via the console). Any attempts to change the passwords for the Agent via an SNMP Manager will fail when the Agent is in this mode. Locally defined passwords will survive a power-cycle.
05-2806A01, Rev. H iNET Series Reference Manual 149In either case, the SNMP Manager needs to know the initial passwords that are being used in order to talk to the Agent. If the Agent’s passwords are configured via the Manager, then they can be changed from the Man-ager. If the passwords are managed locally, then the Manager must be re-configured with any password changes in order to continue to talk to the Agent.Password-Mode Management ChangesWhen the password management mode is changed, the active passwords used by the Agent may also change. Some common scenarios are dis-cussed below:Common Scenarios • Passwords are currently being handled by the Manager. The assigned passwords are Microwave (Auth), and Rochester (Priv). Configuration is changed to manage the passwords locally. The passwords stored on the radio were Fairport (Auth), and Churchville (Priv) (If local passwords have never been used, then MDSAuthPwd and MDSPrivPwd will be used). These passwords will now be used by the Agent to re-generate keys. The Manager will need to know these passwords in order to talk to the Agent.• Passwords are currently being managed locally. The local pass-words are Fairport (Auth) and Churchville (Priv). Configuration is changed to handle the passwords from the Manager. The same passwords will continue to be used, but now the Manager can change them.• Passwords are currently being managed locally. The local pass-words are Fairport (Auth) and Churchville (Priv). Passwords are changed to Brighton (Auth) and Perinton (Priv). The Agent will immediately generate new keys based on these passwords and start using them. The Manager will have to be re-configured to use these new passwords.• Passwords are currently being managed locally. The local pass-words are Fairport (Auth) and Churchville (Priv). Configuration is changed to handle the passwords from the Manager. The Man-ager changes the passwords to Brighton (Auth) and Perinton (Priv). The radio is then rebooted. After a power-cycle, the radio will use the passwords stored in flash, which are Fairport (Auth) and Churchville (Priv). The Manager will have to be re-config-ured to use these new passwords.
150 iNET Series Reference Manual 05-2806A01, Rev. HTable 4-5. SNMP Traps (Sorted by Code) SNMP Trap Severity DescriptionsystemBoot(32) INFORMATIONAL SNR Within threshold/Below thresholdsystemReboot(33) MAJOR Telnet User Logged Out/Logged InstartScan(34) INFORMATIONAL Reprogramming StartedrxBeaconErrored(35) INFORMATIONAL Received Beacon - Netname Does Not MatchrxBeaconWrongNetworkName (36) INFORMATIONAL Received Beacon - AP is BlacklistedrxBeaconFromBlacklistAP(37) MAJOR Max Beacon Wait Time ExceededexpectedSync(38) INFORMATIONAL Expected Sync Lost/EstablishedhopSync(39) INFORMATIONAL Hop Sync Lost/Establishedsnr(41) INFORMATIONAL Scanning Startedber(42) INFORMATIONAL Bit Error Rate Below threshold/Above thresholdassociated(43) MAJOR Association Lost/EstablishedapParmChange(44) MINOR Association Lost - AP Hop Parameter ChangedreprogStarted(45) MAJOR Reprogramming FailedreprogComplete(46) MAJOR Rem Ethernet Link Connected/DisconnectedreprogFailed(47) INFORMATIONAL Reprogramming CompletetelnetLogin(48) MAJOR Telnet Access Locked for 5 MinhttpLogin(49) MAJOR HTTP User Logged Out/Logged IncountrySkipZoneMismatch(50) INFORMATIONAL Country/SkipZone MismatchdesiredAPIPMismatch(51) INFORMATIONAL Desired AP IP Addr MismatcheventLogCleared(52) INFORMATIONAL Log ClearedauthDemoMode(53) MAJOR Auth Demo Mode Expired -- Rebooted Radio/EnabledkeyEntered(54) MAJOR Auth Key Entered - Key Valid/Key InvalidapEthLinkDown(55) MAJOR Association Lost - AP's Ethernet Link DownnoBeacons(56) MAJOR MAC Param ChangedapNotApproved(57) MAJOR Current AP No Longer ApprovednetnameChanged(58) MAJOR Association Lost - Local Network Name ChangedipAddrChanged(59) MAJOR Association Lost - Local IP Address ChangedassocTryFail(60) MAJOR Association Attempt Success/FailedremEthLinkLost(61) INFORMATIONAL Received Beacon - Valid/ErroredconsoleLogin(62) MAJOR Console User Logged Out/Logged InconsoleLockdown(63) MAJOR Console Access Locked for 5 MintelnetLockdown(64) INFORMATIONAL System Bootup (power on)httpLockdown(65) MAJOR HTTP Access Locked for 5 MineventRemote(66) INFORMATIONAL Remote added/removed from internal databaseeventEndpoint(67) INFORMATIONAL Endpoint added/removed from internal databaserouteAdded(68) INFORMATIONAL Radio attempted but failed to add a route to its internal routing table
05-2806A01, Rev. H iNET Series Reference Manual 151routeDeleted(69) INFORMATIONAL Radio attempted but failed to delete a route from its internal routing tablesinRemSwitch(70) INFORMATIONAL Remote mode was switched (serial to ethernet, ethernet to serial)ChanCnt(71) INFORMATIONAL Number of channels defined does not match (Channel 130 only)tftpConnection(73) INFORMATIONAL TFTP Server on AP started or finished a transferapNetNameChanged(74) MAJOR Remote lost association due to a change in the AP’s netnameipConnectivityOK(75) INFORMATIONAL Radio is associated AND 1) has an IP address statically defined, OR 2) received an IP address via DHCPcompressionChanged(76) INFORMATIONAL Compression state has changed (enabled, disabled)macDecryptError(77) INFORMATIONAL MAC has received a packet that it could not decryptlanPortStatus(78) INFORMATIONAL Ethernet port has changed (enabled, disabled)tftpConnFailed(79) INFORMATIONAL TFTP server on AP failed to transfersdbError(80) INFORMATIONAL AP encountered an internal database errorTable 4-5. SNMP Traps (Sorted by Code)  (Continued)SNMP Trap Severity Description
152 iNET Series Reference Manual 05-2806A01, Rev. H
05-2806A01, Rev. H iNET Series Reference Manual 1535TECHNICAL REFERENCE5 Chapter Counter Reset ParagraphContents5.1   DATA INTERFACE CONNECTORS ........................................ 1555.1.1   LAN Port ....................................................................................1555.1.2   COM1 Port  ................................................................................1565.1.3   COM2 Port  ................................................................................1565.2   FUSE REPLACEMENT PROCEDURE ................................... 1575.3   TECHNICAL SPECIFICATIONS.............................................. 1585.4   CHANNEL HOP TABLE........................................................... 161
154 iNET Series Reference Manual 05-2806A01, Rev. H
05-2806A01, Rev. H iNET Series Reference Manual 1555.1 DATA INTERFACE CONNECTORSThree data interface connectors are provided on the face of the trans-ceiver. The first, the LAN Port, is an RJ-45 connector. The other two use two DB-9 interface connectors that use the RS-232 (EIA-232) signaling standard. Note that the connector for COM1 Port is DCE (Female DB-9) and the COM2 Port is DTE (male DB-9). The transceiver meets U.S.A.’s FCC Part 15, Class A limits when used with shielded data cables. 5.1.1 LAN PortThe transceiver’s LAN Port is used to connect the radio to an Ethernet network. The transceiver provides a data link to an Internet Pro-tocol-based (IP) network via the Access Point station. Each radio in the network must have a unique IP address for the network to function prop-erly.• To connect a PC directly to the radio’s LAN port, an RJ-45 to RJ-45 cross-over cable is required. • To connect the radio to a Ethernet hub or bridge, use a straight-through cable.The connector uses the standard Ethernet RJ-45 cables and wiring. For custom-made cables, use the pinout information in Figure 5-1 and Table 5-1.Figure 5-1. LAN Port (RJ-45) Pinout(Viewed from the outside of the unit) Table 5-1. LAN Port (IP/Ethernet)Pin Functions Ref.1 Transmit Data (TX) High2 Transmit Data (TX) Low3 Receive Data (RX) High4 Unused5 Unused6 Receive Data (RX) Low7 Unused8 UnusedCAUTIONRADIO FREQUENCYINTERFERENCE POTENTIAL1 2 3 4 5 6 7 8
156 iNET Series Reference Manual 05-2806A01, Rev. H5.1.2 COM1 PortTo connect a PC to the transceiver’s COM1 port use a DB-9M to DB-9F “straight-through” cable. These cables are available commercially, or may be constructed using the pinout information in Figure 5-2 and Table 5-2.Figure 5-2. COM1 Port (DCE)(Viewed from the outside of the unit.) 5.1.3 COM2 PortTo connect a PC to the transceiver’s COM2 port use a DB-9F to DB-9M “straight-through” cable. These cables are available commercially, or may be constructed using the pinout information in Figure 5-3 and Table 5-3.Figure 5-3. COM2 Port (DTE)Viewed from the outside of the radioTable 5-2. COM1 Port Pinout, DB-9F/RS-232 InterfacePin  Functions DCE1 Unused2 Receive Data (RXD) <—[Out3 Transmit Data (TXD) —>[In4 Unused5 Signal Ground (GND)6–9 UnusedTable 5-3. COM2 Port, DB-9M/EIA-232 InterfacePin  Functions DTE1 Data Carrier Detect (DCD) In]<—2 Receive Data (RXD) In]<—3 Transmit Data (TXD) Out]—>4 Data Terminal Ready (DTR) Out]—>5 Signal Ground (GND)15965169
05-2806A01, Rev. H iNET Series Reference Manual 1575.2 FUSE REPLACEMENT PROCEDUREAn internal fuse protects the transceiver from over-current conditions or an internal component failure. It should not be replaced until you are certain you are in a safe (non-flammable) environment.1. Disconnect the primary power source and all other connections to the unit.2. Place the radio on its back and remove the four Phillips screws on the bottom cover.3. Carefully separate the top and bottom covers. There is a flat ribbon cable between the top cover’s LEDs and the unit motherboard. You do not need to disconnect the ribbon cable.4. Locate the fuse and fuse holder between the COM1 port and the power connector. See Figure 5-4 for details.5. Loosen the fuse from the holder using a very small screwdriver. Use a small pair of needle-nose pliers to pull the fuse straight up and remove it.6. Using an Ohmmeter, or other continuity tester, verify the fuse is blown.7. Install a new fuse by reversing the process.Littelfuse P/N: 0454002; 452 Series, 2 Amp SMF Slo-BloGE MDS P/N: 29-1784A036 Data Set Ready (DSR) In]<—7 Request-to-Send (RTS) Out]—>8 Clear-to-Send (CTS) In]<—9 UnusedTable 5-3. COM2 Port, DB-9M/EIA-232 InterfacePin  Functions DTE
158 iNET Series Reference Manual 05-2806A01, Rev. H8. Install the covers and check the transceiver for proper operation.Invisible place holder5.3 TECHNICAL SPECIFICATIONSGENERALTemperature Range: –30° C to +60° C (–22° F to 140° F)Humidity: 95% at +40° C (104° F); non-condensingPrimary Power: 10–30 Vdc (13.8 Vdc Nominal)External Power Supply Options: 110–120/210–220 VacSupply Current (typical): (9 Watts Maximum @ 1 Watt RF Output)Transmit: 7 watts (10.5-24 Vdc)9 watts (24.5-30 Vdc)Receive: 2.8 watts (10.5-24 Vdc)3.5 watts (24.5-30 Vdc)MTBF: 35 Years (Telcordia Method 1, Case 3)Size (Excluding mtg. hardware): 1.25" x 6.75" x 4.5" (H x W x D)3.15 x 17.15 x 11.43 cmMounting w/Optional Hardware: • DIN Rail• Flat surface mounting brackets• 19” rack (1U high)Weight: 908 g / 2 lbCase: Cast AluminumBoot Time: ≈ 30 sec Time Required to Associatewith Access Point: ≈ 20 sec APPROVALS/HOMOLOGATION• FCC Part 15.247iNET FCC identifier: E5MDS-NH900iNET-II FCC identifier: E5MDS-INETII• Industry Canada RSS-210iNET certification no.: 3738A 12098iNET-II certification no.: 3738A-INETII Figure 5-4. Internal Fuse and Holder Assembly Location
05-2806A01, Rev. H iNET Series Reference Manual 159• UL/CSA Class 1, Div. 2; Groups A, B, C and D hazardous locations• Complies with the following IEEE Std 1613™-2003 Communications Networking Devices in Electric Power Substations classifica-tions:4.1.1 Environmental Class B4.1.2 Environmental Storage Class A7.12 Device Performance Class 1• Contact factory for information on availability and governmental approvals in other countriesMANAGEMENT• HTTP, HTTPS (Embedded Web server)• Telnet, SSH, COM1 serial port (Text-based menu)• SNMP v1/v2/v3• SYSLOG• GE MDS NETview MS™DATA CHARACTERISTICSPORTS:Ethernet:Interface Connectors: RJ-45 StandardData Rate: 10BaseT (10 Mbps)Serial (2 Ports):Signaling Standard: EIA-232/V.24Interface Connectors: DB-9Interface: COM1: DCE / COM2: DTEData Rate: 1200–115,200 bpsasynchronousData Latency: < 10 ms typicalByte Formats: 7 or 8-bit; even, odd, or no-parity; 1 or 2 stop bitsOPERATING MODES: • Configurable as Access Point or Remote StationPROTOCOLS: • Wireless: CSMA/CA (Collision Avoidance)• Ethernet: IEEE 802.3, Ethernet II, Spanning Tree (Bridging), IGMP• TCP/IP: DHCP, ICMP, UDP, TCP, ARP, Multicast, SNTP, TFTP• Serial: PPP, Encapsulation over IP (tunneling) for serial async multidrop protocols including Modbus, DNP.3, DF1, BSAP• Special: Allen-Bradley EtherNet/IP* - Modbus/TCP (optional)
160 iNET Series Reference Manual 05-2806A01, Rev. HCYBER SECURITY• Cyber Security, Level 1 (iNET-II only): • AES-128 encryption (optional)• Cyber Security, Level 2: • RC4-128 encryption (iNET only)•Automatic rotating key algorithm•Authentication: 802.1x, EAP/TLS, PKI,   PAP, CHAP•Management: SSL, SSH, HTTPS•Approved AP/Remotes list (local authentication)•Failed login lockdown•900 MHz operation and proprietary data framingRADIO CHARACTERISTICSGENERAL:Frequency Range: 902–928 MHz ISM BandFrequency Hopping Range: iNET: Ten user-configurable 2.5 MHz-wide zones, each containing 8 frequencies (iNET)iNET-II: From one and up to 75 overlapping channelsHop Patterns: 8192, based on network nameFrequency Stability: 20 ppmTRANSMITTER:Power Output(at antenna connector): 0.1 to 1.0 watt (+20 dBm to +30 dBm) ±1.0 dB, set by userDuty Cycle: ContinuousModulation Type: Binary CPFSKOutput Impedance: 50 OhmsSpurious: –67 dBcOccupied Bandwidth: GE MDS iNET: 316.5 kHzGE MDS iNET-II: 600 kHzRECEIVER:Type: Double conversion superheterodyneSensitivity: GE MDS iNET: –92 dBm @ 512 kbps < 1x10-6 BERGE MDS iNET: –99 dBm @ 256 kbps < 1x10-6 BERGE MDS iNET-II: –92 dBm @ 1 Mbps < 1x10-6 BERGE MDS iNET-II: –97 dBm @ 512 kbps < 1x10-6 BERIntermodulation: 59 dB Minimum (EIA)Desensitization: 70 dBSpurious: 60 dB
05-2806A01, Rev. H iNET Series Reference Manual 161TRANSMIT/RECEIVE RANGE (Nominal)GE MDS iNET–256 kbps  GE MDS iNET-II–512 kbpsFixed Range (typical): 15 miles (24 km) 12 miles (19 km)Fixed Range (maximum): 60 miles (97 km) 30 miles (48 km)Mobile Range (parked): 5 miles (8 km) 3 miles (5 km)Mobile Range (moving): 3 miles (5 km) 1 mile (2 km)GE MDS iNET–512 kbps GE MDS iNET-II–1024 kbpsFixed Range (typical): 8 miles (13 km) 8 miles (13 km)Fixed Range (maximum): 15 miles (24 km) 15 miles (24 km)Note: Specifications subject to change without notice or obligation.NOTE: Range calculations for fixed locations assume a 6 dBd gainOmnidirectional antenna on a 100 ft tower at the AP, a 10 dBdgain Yagi on a 25 ft mast at the remote with output powerdecreased to yield maximum allowable EIRP (36 dBm), a 10dB fade margin, and a mix of agricultural and commercialterrain with line of sight.Range calculations for mobile units assume a 6 dBd gain Omnion a 100 ft tower at the AP, a 5 dBd gain Omni with 1 wattoutput power at 6 ft height, a 10 dB fade margin, and 90%confidence with near line-of-sight in a mix of agricultural andcommercial terrain.Actual performance is dependent on many factors includingantenna height, blocked paths, and terrain.5.4 CHANNEL HOP TABLEThe GE MDS iNET transceiver’s hop table consists of 80 channels, numbered 0 to 79 as listed in Table 5-4. Center frequencies are calcu-lated as follows (where Fn is the center frequency of channel n): Fn = 902.5 MHz + n*316.5 kHzThe GE MDS iNET-II transceiver operates on the same channel assign-ments, but because the modulation bandwidth is 600 kHz instead of 316.5 kHz it is recommended that the installer restrict channel usage to every other channel for units operating in the same area.NOTE: Channels 24, 26, and 55 are not used.
162 iNET Series Reference Manual 05-2806A01, Rev. HTable 5-4. Channel Hop Table  Zone Channel Frequency1 0 902.5000(iNET FHSS lowest channel)1 1 902.8165(iNET-II DTS lowest channel)1 2 903.13301 3 903.44951 4 903.76601 5 904.08251 6 904.39901 7 904.71552 8 905.03202 9 905.34852 10 905.66502 11 905.98152 12 906.29802 13 906.61452 14 906.93102 15 907.24753 16 907.56403 17 907.88053 18 908.19703 19 908.51353 20 908.83003 21 909.14653 22 909.46303 23 909.77954 24 910.09604 25 910.41254 26 910.72904 27 911.04554 28 911.36204 29 911.67854 30 911.99504 31 912.31155 32 912.62805 33 912.94455 34 913.26105 35 913.57755 36 913.89405 37 914.21055 38 914.52705 39 914.8435
05-2806A01, Rev. H iNET Series Reference Manual 1636 40 915.16006 41 915.47656 42 915.79306 43 916.10956 44 916.42606 45 916.74256 46 917.05906 47 917.37557 48 917.69207 49 918.00857 50 918.32507 51 918.64157 52 918.95807 53 919.27457 54 919.59107 55 919.90758 56 920.22408 57 920.54058 58 920.85708 59 921.17358 60 921.49008 61 921.80658 62 922.12308 63 922.43959 64 922.75609 65 923.07259 66 923.38909 67 923.70559 68 924.02209 69 924.33859 70 924.65509 71 924.971510 72 925.288010 73 925.604510 74 925.921010 75 926.237510 76 926.554010 77 926.870510 78 927.1870(iNET-II DTS highest channel)10 79 927.5035(iNET FHSS highest channel)Table 5-4. Channel Hop Table   (Continued)Zone Channel Frequency
164 iNET Series Reference Manual 05-2806A01, Rev. H
05-2806A01, Rev. H iNET Series Reference Manual 1656GLOSSARY OF TERMSAND ABBREVIATIONS6 Chapter Counter Reset ParagraphIf you are new to wireless IP/Ethernet systems, some of the terms used in this guide may be unfamiliar. The following glossary explains many of these terms and will prove helpful in understanding the operation of your radio network.Access Point (AP)—The transceiver in the network that provides syn-chronization information to one or more associated Remote units. AP units may be configured for either the Access Point (master) or Remote services. (See “Network Configuration Menu” on Page 37.)Active Scanning—See Passive ScanningAntenna System Gain—A figure, normally expressed in dB, repre-senting the power increase resulting from the use of a gain-type antenna. System losses (from the feedline and coaxial connectors, for example) are subtracted from this figure to calculate the total antenna system gain.AP—See Access PointAssociation—Condition in which the frequency hopping pattern of the Remote is synchronized with the Access Point station and is ready to pass traffic.Authorization Key—Alphanumeric string (code) that is used to enable additional capabilities in the transceiver.Bit—The smallest unit of digital data, often represented by a one or a zero. Eight bits (plus start, stop, and parity bits) usually comprise a byte.Bits-per-second—See BPS.BPDU—Bridge Protocol Data UnitsBPS—Bits-per-second (bps). A measure of the information transfer rate of digital data across a communication channel.Byte—A string of digital data usually made up of eight data bits and start, stop and parity bits.CSMA/CA—Carrier Sense Multiple Access/Collision AvoidanceCSMA/CD—Carrier Sense Multiple Access/Collision DetectionCyclic Redundancy Check (CRC)—A technique used to verify data integrity. It is based on an algorithm which generates a value derived
166 iNET Series Reference Manual 05-2806A01, Rev. Hfrom the number and order of bits in a data string. This value is com-pared with a locally-generated value and a match indicates that the mes-sage is unchanged, and therefore valid.Datagram—A data string consisting of an IP header and the IP message within.dBi—Decibels referenced to an “ideal” isotropic radiator in free space. Frequently used to express antenna gain.dBm—Decibels referenced to one milliwatt. An absolute unit used to measure signal power, as in transmitter power output, or received signal strength.DCE—Data Circuit-terminating Equipment (or Data Communications Equipment). In data communications terminology, this is the “modem” side of a computer-to-modem connection. COM1 Port of the transceiver is set as DCE.Decibel (dB)—A measure of the ratio between two signal levels. Fre-quently used to express the gain (or loss) of a system.Delimiter—A flag that marks the beginning and end of a data packet.DHCP (Dynamic Host Configuration Protocol)—An Internet stan-dard that allows a client (i.e. any computer or network device) to obtain an IP address from a server on the network. This allows network admin-istrators to avoid the tedious process of manually configuring and man-aging IP addresses for a large number of users and devices. When a network device powers on, if it is configured to use DHCP, it will con-tact a DHCP server on the network and request an IP address. The DHCP server will provide an address from a pool of addresses allo-cated by the network administrator. The network device may use this address on a “time lease” basis or indefinitely depending on the policy set by the network administrator. The DHCP server can restrict alloca-tion of IP addresses based on security policies. An Access Point may be configured by the system administrator to act as a DHCP server if one is not available on the wired network.DTE—Data Terminal Equipment. A device that provides data in the form of digital signals at its output. Connects to the DCE device.Encapsulation—Process in by which, a complete data packet, such asModbus frame or any other polled asynchronous protocol frame, isplaced in the data portion of another protocol frame (in this case IP) tobe transported over a network. Typically this action is done at the receiv-ing end, before being sent as an IP packet to a network. A similar re-versed process is applied at the other end of the network extracting thedata from the IP envelope, resulting in the original packet in the originalprotocol.
05-2806A01, Rev. H iNET Series Reference Manual 167Endpoint—IP address of data equipment connected to the ports of the radio.Equalization—The process of reducing the effects of amplitude, fre-quency or phase distortion with compensating networks.Fade Margin—The greatest tolerable reduction in average received signal strength that will be anticipated under most conditions. Provides an allowance for reduced signal strength due to multipath, slight antenna movement or changing atmospheric losses. A fade margin of 15 to 20 dB is usually sufficient in most systems.Fragmentation—A technique used for breaking a large message down into smaller parts so it can be accommodated by a less capable media.Frame—A segment of data that adheres to a specific data protocol and contains definite start and end points. It provides a method of synchro-nizing transmissions.Frequency Hopping—The spread spectrum technique used by the transceiver, where two or more associated radios change their operating frequencies several times per second using a set pattern. Since the pat-tern appears to jump around, it is said to “hop” from one frequency to another.Frequency Zone—The radio uses up to 80 discrete channels in the 902 to 928 MHz spectrum. A group of 8 channels is referred to as a zone; in total there are 10 zones.Hardware Flow Control—A transceiver feature used to prevent data buffer overruns when handling high-speed data from the connected data communications device. When the buffer approaches overflow, the radio drops the clear-to-send (CTS) line, that instructs the connected device to delay further transmission until CTS again returns to the high state.Hop Pattern Seed—A user-selectable value to be added to the hop pat-tern formula in an unlikely event of nearly identical hop patterns of two collocated or nearby radio networks to eliminate adjacent-network inter-ference.Host Computer—The computer installed at the master station site, that controls the collection of data from one or more remote sites.HTTP—Hypertext Transfer ProtocolIAPP (inter-Access Point Protocol)—A protocol by which access points share information about the stations that are connected to them. When a station connects to an access point, the access point updates its database. When a station leaves one access point and roams to another
168 iNET Series Reference Manual 05-2806A01, Rev. Haccess point, the new access point tells the old access point, using IAPP, that the station has left and is now located on the new access point.ICMP—Internet Control Message ProtocolIGMP (Internet Gateway Management Protocol)—Ethernet level protocol used by routers and similar devices to manage the distribution of multicast addresses in a network.IEEE—Institute of Electrical and Electronic EngineersImage (File)—Data file that contains the operating system and other essential resources for the basic operation of the radio’s CPU. LAN—Local Area NetworkLatency—The delay (usually expressed in milliseconds) between when data is applied at the transmit port at one radio, until it appears at the receive port at the other radio.MAC—Media Access ControlMD5—A highly secure data encoding scheme. MD5 is a one-way hash algorithm that takes any length of data and produces a 128 bit “finger-print.” This fingerprint is “non-reversible,” it is computationally infea-sible to determine the file based on the fingerprint. For more details review “RFC 1321” available on the Internet.MIB—Management Information BaseMicrocontroller Unit—See MCU.Mobile IP—An emerging standard by which access points and stations maintain network connectivity as the stations move between various IP networks. Through the use of Mobile IP a station can move from its home IP network to a foreign network while still sending and receiving data using it's original IP address. Other hosts on the network will not need to know that the station is no longer in its home network and can continue to send data to the IP address that was assigned to the station. Mobile IP also uses DHCP when the station moves into a foreign net-work.Mobile Station—Refers to a station that moves about while main-taining active connections with the network. Mobility generally implies physical motion. The movement of the station is not limited to a specific network and IP subnet. In order for a station to be mobile it must estab-lish and tear down connections with various access points as it moves through the access points' territory. To do this, the station employs roaming and Mobile IP.MTBF—Mean-Time Between Failures
05-2806A01, Rev. H iNET Series Reference Manual 169Multiple Address System (MAS)—See Point-Multipoint System.Network Name—User-selectable alphanumeric string that is used to identify a group of radio units that form a communications network. The Access Point and all Remotes within a given system should have the same network address.Network-Wide Diagnostics—An advanced method of controlling and interrogating GE MDS radios in a radio network.NTP—Network Time ProtocolPacket—The basic unit of data carried on a link layer. On an IP net-work, this refers to an entire IP datagram or a fragment thereof.Passive Scanning—Scanning is a process used by stations to detect other access points on network to which it may connect if it needs to roam. Passive scanning is a slower process in which it listens for infor-mation offered by the access points on a regular basis. Active scanning is a faster process in which the station sends out probe message to which the access points respond. Passive scanning can be done while main-taining the current network connectivity. Active scanning affects the RF configuration of the radio and therefore, at least temporarily, discon-nects the station from the access point.PING—Packet INternet Groper. Diagnostic message generally used to test reachability of a network device, either over a wired or wireless net-work.Point-Multipoint System—A radio communications network or system designed with a central control station that exchanges data with a number of remote locations equipped with terminal equipment.Poll—A request for data issued from the host computer (or master PLC) to a remote radio.Portability—A station is considered connected when it has successfully authenticated and associated with an access point. A station is consid-ered authenticated when it has agreed with the access point on the type of encryption that will be used for data packets traveling between them. The process of association causes a station to be bound to an access point and allows it to receive and transmit packets to and from the access point. In order for a station to be associated it must first authenticate with the access point. The authentication and association processes occur automatically without user intervention.Portability refers to the ability of a station to connect to an access point from multiple locations without the need to reconfigure the network set-tings. For example, a remote transceiver that is connected to an access point may be turned off, moved to new site, turned back on, and,
170 iNET Series Reference Manual 05-2806A01, Rev. Hassuming the right information is entered, can immediately reconnect to the access point without user intervention.PLC—Programmable Logic Controller. A dedicated microprocessor configured for a specific application with discrete inputs and outputs. It can serve as a host or as an RTU.PuTTY—A free implementation of Telnet and SSH for Win32 and Unix platforms. It is written and maintained primarily by Simon Tatham Refer to http://www.pobox.com/~anakin/ for more information.Remote—A transceiver in a network that communicates with an asso-ciated Access Point.RFI—Radio Frequency InterferenceRoaming—A station's ability to automatically switch its wireless con-nection between various access points (APs) as the need arises. A station may roam from one AP to another because the signal strength or quality of the current AP has degraded below what another AP can provide. When two access points are co-located for redundancy, roaming allows the stations to switch between them to provide a robust network. Roaming may also be employed in conjunction with Portability where the station has been moved beyond the range of the original AP to which it was connected. As the station comes in range of a new AP, it will switch its connection to the stronger signal. Roaming refers to a station's logical, not necessarily physical, move between access points within a specific network and IP subnet.RSSI—Received Signal Strength IndicatorRTU—Remote Terminal Unit. A data collection device installed at a remote radio site.SCADA—Supervisory Control And Data Acquisition. An overall term for the functions commonly provided through an MAS radio system.SNMP—Simple Network Management ProtocolSNR—Signal-to-Noise Ratio. A measurement of the desired signal to ambient noise levels.This measurement provides a relative indication of signal quality. Because this is a relative number, higher signal-to-noise ratios indicate improved performance.SNTP—Simple Network Time ProtocolSSL—Secure Socket LayerSSH—Secure ShellSTP—Spanning Tree Protocol
05-2806A01, Rev. H iNET Series Reference Manual 171SWR—Standing-Wave Ratio. A parameter related to the ratio between forward transmitter power and the reflected power from the antenna system. As a general guideline, reflected power should not exceed 10% of the forward power (≈ 2:1 SWR).TCP—Transmission Control ProtocolTFTP—Trivial File Transfer ProtocolTrap Manager—Software that collects SNMP traps for display or log-ging of events.UDP—User Datagram ProtocolUTP—Unshielded Twisted PairWINS—Windows Internet Naming Service. Part of Microsoft Win-dows NT and 2000 servers that manages the association of workstation names and locations with Internet Protocol addresses. It works without the user or an administrator having to be involved in each configuration change. Similar to DNS.Zone—See Frequency Zone.
172 iNET Series Reference Manual 05-2806A01, Rev. H
MDS 05-2806A01, Rev. H iNET Series Reference Manual I-1INDEXNumerics100BaseT 12910BaseT 129802.11b 10AAccess Point (AP), defined 165accessories 17Active Scanning, defined 165, 169Actual Data Rate 86Add Associated Remotes 82AgeTime 96, 97alarm conditions 120correcting 122Alarmed 118Antennaaiming 141directional 136Minimum Feedline Length versus Antenna Gain 135omnidirectional 133polarization 133selection 132SWR check 140system gain 165system gain vs. power output setting 138system gain, defined 165Yagi 134APAuto Upgrade 95Reboot when Upgraded 95applicationIP-to-Serial 71Mixed-Modes 76Point-to-Multipoint Serial-to-Serial 72Point-to-Point Serial-to-Serial 74Serial Port 76ApprovedAccess Points/Remotes List 81Remotes/Access Points List 81Associated 118AssociationDate 95defined 165Process 94Time 95Auth Traps Status 49Authorization Key 108, 111defined 165Authorized Features 108Auto Data Rate MenuSNR Threshold/Delta 58Auto Key Rotation 81Auto-Upgrade/Remote-Reboot 108BBackhaulfor Serial Radio Networks 8Network 9bandpass filter 137BeaconPeriod 53, 145, 146signal 94Begin Wizard 64Bit, defined 165Bits-per-second (bps), defined 165BPDU 144defined 165BPS, defined 165bridging 159remote-to-remote 39Bytesdefined 165in on port 99in on socket 99out on port 99out on socket 99received 92sent 92Ccablefeedlines 134ClearCom# statistics 99Ethernet stats 92Log 89Wireless stats 92Client Inactivity Timeout 68Collocating Multiple Radio Networks 14Commit Changes and Exit Wizard 66, 67, 69, 70, 71compression 52, 145configuration 65, 67, 68, 70, 71basic device parameters 35DHCP server 46editing files 107Ethernet Port 45file 115PPP Mode 70radio parameters 51scripts 105security 78SNMP Agent 47TCP Mode 68UDP mode 64Connection Status 95connectors 155Contact 36
I-2 iNET Series Reference Manual MDS 05-2806A01, Rev. Hcost of deployment 9Count 111CRC (Cyclic Redundancy Check), defined 165CSMACA, defined 165CD, defined 165CurrentAlarms 89AP IP Address 95AP Mac Address 95Custom Data Buffer Size 66, 67, 69, 70, 71Ddatabaud 71baud rate 65, 67, 68, 70buffering 63, 69compression 145rate 52Datagram, defined 166DataRate 96Date 35Format 35dB, defined 166dBi, defined 166dBmdefined 166watts-volts conversion 143DCE, defined 166defaultsreset to factory 111DeleteAll Remotes 82Remote 82Delimiter, defined 166deployment costs 9Description 36DeviceIP Address 71Mode 32Name 32, 36Status 32, 118DHCPdefined 166Netmask 47Diagnostic Tools 120dimensions 129DKEY command 140DNS Address 47DTE 11, 60Dwell Time 52, 146EEIA-232 11Encapsulation, defined 166Encryption 81Phrase 81Ending Address 47Endpointdefined 167Listing 87Listing Menu 97ENI, MDS iNET 900 3Equalization, defined 167EthernetLink (H/W) Watch 46Link Poll Address 46Packet Statistics 92port enabled/disabled 45Rate Limit 45Event Log 86, 88, 118, 120, 122, 123FFade Margin 167Feedlineselection 132, 134Filename 90, 101firewall 147firmwareinstalling 102upgrade 102, 109version 33, 35Flow Control 63, 65, 67, 68, 70, 71hardware, defined 167Force Key Rotation 81Force Reboot 109Fragmentationdefined 167Threshold 53, 146Frame, defined 167Frequency 110zone, defined 167fuse replacement 157Ggainantenna, defined 165system 137Glossary 165–171Go 111HHardwareflow control, defined 167Version 33, 35HopFormat 54pattern 137Pattern Seed 53Sync 118Hoppingchannels 161HTTPdefined 167Security Mode 80
MDS 05-2806A01, Rev. H iNET Series Reference Manual I-3IIETF standard RFC1213 47IGMP 62defined 168ImageCopy 102file, defined 168Verify 102iNET II, differences of 3, 51, 52, 57, 59, 98, 132, 135, 141Installationantenna & feedline 132feedline selection 134general information 3planning 129requirements 129site selection 131site survey 136Interference 136InternetAssigned Numbers Authority 62IP 46Addr 111Address 32, 96, 97, 107Gateway 107Mobile, defined 168Protocol 65, 66, 68, 69, 71tunneling 61KKeytransmitter, for antenna SWR check 140KEY command 140LLANdefined 168Latency 145Latency, defined 168Latest AP Firmware Version 95LEDLAN 116LINK 116, 136, 141PWR 88, 90, 116, 120, 123use during troubleshooting 115Link Established 71LocalArea Network, defined 168IP Port 65, 66Listening IP Port 69Location 36, 107Logged Events 123Lost Carrier Detected 92, 119MMAC Address 96, 97, 144Management Systemuser interfaces 23MD5, defined 168MDS iNET 900 ENI 3MDS Security Suite 15measurementsradio 139MIBdefined 168files 47Mobile IP, defined 168Mobility 58Mobility Capability 11MODBUS 69Modeserial gateway interface 11TCP 11UDP 11Model Number 35MTBF, defined 168MulticastIP Address 65IP Port 65multipleprotocols 9services 9NNEMA 10NetworkName 14, 32Name, defined 169Time Protocol (NTP), defined 169networkmaintenance 99performance verification 85network design 12antennas 13collocating multiple radio networks 14network name 13repeaters 12using multiple Access Points 14Using the AP as a Store-and-Forward Packet Repeater 13using two transceivers to form a repeater station 12NTP (Network Time Protocol), defined 169OOwner 36
I-4 iNET Series Reference Manual MDS 05-2806A01, Rev. HPPacketdefined 169Redundancy Mode 65, 67Size 111Statistics 87, 91, 119PacketsDropped 92, 119Packets-per-Second 145Received 91, 92Received by Zone 93Sent 92Passive Scanning, defined 169Password Reset 111Performance Information Menu 146PING 136defined 169Ping Utility 111PLC 10defined 170Point-Multipoint System, defined 169Point-to-PointLAN Extension 8Link 8Poll, defined 169portantenna 140COM1 11, 60, 72, 132, 156COM2 11, 60, 72, 156IP 72LAN 155not Enabled 71well-known 147Portability, defined 169portsserial 9powerhow much can be used 135transmitter power output 140PPP 63Primary Host Address 68Primary IP Port 68Programmable Logic Controller 10protocolBPDU 144IP 46, 60MODBUS 69PPP 63SNMP 23, 47, 147defined 170SNTP 170STP 144STP, defined 170TCP 61, 68, 71, 75, 145defined 171TFTP 102defined 171UDP 61, 62, 71, 74, 75, 145PuTTY usage 27defined 170RRadioFrequency Interference 15, 136Remote, defined 170Test 110range, transmission 10Read Community String 48RebootDevice 102on Upgrade 109Receive errors 92, 119Received Signal Strength Indicator 132defined 170RedundancyUsing multiple Access Points 14RemoteIP Address 66IP Port 66Listing 87Listing Menu 96Performance Listing 87, 98radio, defined 170Terminal Unit 10Terminal Unit, defined 170Repeater 12antennas 13Network Name 13Using the AP as a Store-and-Forward Packet Repeater 13Using two transceivers to form a repeater station 12reprogramming 100Resetting the Password 111Restart DHCP Server 47Retries 92, 119Retrieve File 102, 106Retry errors 92, 119RetryEr 98RF Output Power 52, 86RFI 15defined 170Roaming, defined 170RSSI 111, 119, 132, 141by Zone 86, 87defined 170Threshold 54RTS Threshold 53, 146RTS/CTS handshaking 65RTU 10, 60, 72, 75defined 170RxBCMC 98RxPkts 97, 98RxRate 98RxViaEP 98
MDS 05-2806A01, Rev. H iNET Series Reference Manual I-5SSave Changes 82SCADA 9, 10, 62defined 170Scanning 118Active, defined 169Passive, defined 169Seamless Inter-Frame Delay 65, 67, 69, 70, 71SecondaryHost Address 68IP Port 68securityApproved Access Points/Remotes List 81Auto Key Rotation 81encryption 81Encryption Phrase 81Force Key Rotation 81general information 4HTTP Security Mode 80risks 16suite 15Telnet Access 80Two-Way Authentication 79User Password 79SendFile 106Log 89Sending LCP Requests 71SerialConfiguration Wizard 63Data Statistics 99encapsulation 61Mode 65, 67, 69, 70, 71Number 33, 35Port Statistics 119radio networks, backhaul 8Server Status 47Signal strength 132Signal-to-Noise Ratio 86defined 170Simple NetworkManagement Protocol, defined 170Time Protocol, defined 170Site selection 131SNMP 23defined 170Mode 49, 80traps 150usage 147V3 Passwords 49SNR 54defined 170Threshold 54SNTPdefined 170Spanning Tree Protocol 144Spanning Tree Protocol, defined 170Specifications 158–161SSH, defined 170SSL, defined 170Standing Wave Ratio 171StartingAddress 47Information Screen 34State 96Status 32, 64, 66, 68, 69, 71STP, defined 170SWR 140, 171performance optimization 140Syslog Server 90system gain, antenna 165system gain, antenna (defined) 165TTCP 11, 75, 145Client 62defined 171Server 62Telnet 72Access 80Test Mode 110TFTPdefined 171Host Address 89, 101, 106Time-out 90Timeout 102, 106Time 35Time to Live (TTL) 65TransmissionControl Protocol, defined 171range 10transparent encapsulation 61TrapCommunity String 48Manager 49Manager, defined 171Version 49Troubleshooting 115–125Using the Embedded Management System 116Two-Way Authentication 79TX Output Power 110TxKey 110TxPkt 97TxPkts 98TxViaEP 98UUDP 11, 62, 74, 75, 145defined 171mode 64Unit Name 107Uptime 33, 35User Password 79Using multiple Access Points 14
I-6 iNET Series Reference Manual MDS 05-2806A01, Rev. HVV3Authentication Password 49Privacy Password 49via Remote 97ViewApproved Remotes 82Current Alarms 90Current Settings 64Event Log 91Log 89VLAN 38, 39, 40, 77Configuring for operation with 41Configuring IP Address with VLAN disabled 43Configuring IP Address with VLAN enabled 42volts-dBm-watts conversion 143Wwatts-dBm-volts conversion 143WINSAddress 47defined 171WirelessNetwork Status 87, 94Packet Statistics 91wizardserial configuration 63Write community String 48YYagi antenna 134ZZone, defined 171
IN CASE OF DIFFICULTY...GE MDS products are designed for long life and trouble-free operation. However, this equipment, as with all electronic equipment, may have an occasional component failure. The following infor-mation will assist you in the event that servicing becomes necessary.TECHNICAL ASSISTANCETechnical assistance for GE MDS products is available from our Technical Support Department during business hours (8:00 A.M.—5:30 P.M. Eastern Time). When calling, please give the complete model number of the radio, along with a description of the trouble/symptom(s) that you are experiencing. In many cases, problems can be resolved over the telephone, without the need for returning the unit to the factory. Please use one of the following means for product assistance:Phone: 585 241-5510  E-Mail: TechSupport@GEmds.comFAX: 585 242-8369 Web: www.GEmds.comFACTORY SERVICEComponent level repair of radio equipment is not recommended in the field. Many components are installed using surface mount technology, which requires specialized training and equipment for proper servicing. For this reason, the equipment should be returned to the factory for any PC board repairs. The factory is best equipped to diagnose, repair and align your radio to its proper operating specifications.If return of the equipment is necessary, you will be issued a Service Request Order (SRO) number. The SRO number will help expedite the repair so that the equipment can be repaired and returned to you as quickly as possible. Please be sure to include the SRO number on the outside of the ship-ping box, and on any correspondence relating to the repair. No equipment will be accepted for repair without an SRO number.A statement should accompany the radio describing, in detail, the trouble symptom(s), and a description of any associated equipment normally connected to the radio. It is also important to include the name and telephone number of a person in your organization who can be contacted if additional information is required.The radio must be properly packed for return to the factory. The original shipping container and packaging materials should be used whenever possible. All factory returns should be addressed to:GE MDSProduct Services Department(SRO No. XXXX)175 Science ParkwayRochester, NY 14620 USAWhen repairs have been completed, the equipment will be returned to you by the same shipping method used to send it to the factory. Please specify if you wish to make different shipping arrange-ments. To inquire about an in-process repair, you may contact our Product Services Group at 585-241-5540 (FAX: 585-242-8400), or via e-mail at ProductServices@GEmds.com.
GE MDS, LLCRochester, NY 14620General Business: +1 585 242-9600FAX: +1 585 242-9620Web: www.GEmds.com175 Science Parkway

Navigation menu