G4S Monitoring Technologies PID915 OM247 PID3 User Manual User guide 3

G4S Monitoring Technologies Limited OM247 PID3 User guide 3

Contents

User guide 3

Document Classication: PublicOM247-FIT Fitting Tool & Key Fob Safety GuideUser Safety and Regulations
Page 2Document Classication: PublicThis guide contains basic regulatory and safety information.Document Number: 94-0175-01Revision: 1.0Issue Date: 16/06/2014About This Manual
Page 3Document Classication: PublicOperational WarningsImportant information on safe and efcient operation. Read this information before using the device. For safe and efcient use of the device, observe the guidelines outlined below.Environmental Specication10% to 90% relative humidityOperational Temperature range -20°C to +60°C(AC Power Adaptor: RH 20% to 85%, Operating Temperature 0 to 40°C)OperationThe equipment must be used by a SERVICE PERSON.Battery Charging (Fitting Tool Only)When not in use, disconnect the battery charger from both the device and the mains electricity supply. To halt charging, remove the charging clip from the device.User Safety
Page 4Document Classication: Public Do not disassemble, open, crush, deform or puncture the product. Do not modify, remanufacture, attempt to insert foreign objects, expose to re, explosion, or any other hazards. Only use an approved AC power adaptor with the Fitting Tool. Use of an unapproved charger may present a risk of re, explosion, leakage or other hazard.Approved AC Power AdaptorSource: G4SMTLModel: @3A-181WP06Part Number: 39-0023-3Input Rating: 100-240V VAC, 50-60Hz, 600mAOutput Rating: 6VDC, 3AProduct Handling
Page 5Document Classication: PublicThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Statements
Page 6Document Classication: PublicFCC Statements (continued)Modications not expressly approved by the manufacturer could void the user’s authority to operate the equipment under FCC rules.This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. These products meet the FCC Radiofrequency Emission Guidelines and are certied with the FCC as:FCC ID: 2ACGBFIT915FCC ID: 2ACGBPID915The FCC ID is located on a label on the rear face of the product.
Page 7Document Classication: PublicWe hereby declare that these products are in conformance to all essential requirements of the R&TTE Directive 1999/5/EC. The products are marked with the ‘CE’ symbol and can be used throughout the European Community.This indicates compliance with the R&TTE Directive 1999/5/EC and meets the relevant parts of the following technical specications: EN 301 489-1 v1.6.1:2005 EN 300-220-2 v2.1.1EU Regulatory ConformanceThis symbol indicates that this product should be recycled and not be disposed of in unsorted municipal waste. This product should be returned to the supplier for correct disposal.

Navigation menu