Futaba T7PX-24G Radio Control User Manual
Futaba Corporation Radio Control
UserManual.wiki
>
Futaba
>
T7PX-24G User Manual
>
User Manual (P116-192)
Contents
1.
User Manual (P1-40)
2.
User Manual (P41-116)
3.
User Manual (P116-192)
User Manual (P116-192)
Navigation menu
Upload a User Manual
Namespaces
Wiki Guide
HTML
PDF
Info
Views
User Manual
Discussion / Help
Navigation
![117FunctionDual ESC2 (Channel setup)The channel list screen used for the front ESC channel is displayed. Tap the auxiliary chan-nel that connected the front ESC channel.- When all channels are in use, a screen saying "No assignable channel" is displayed, please turn off other mixing and make an unused channel. You can check the mixing used on the channel setting screen (page 75).For S-FHSS (analog) system, 1 to 7 chan-nels are displayed.If there is no assignable channel, tap [Close]. Turn off other mixing and make assignable channels.3 (Drive ratio adjustment)Adjust the front and rear motor controller operation amount by or button. The button increases and the button de-creases the rear ratio.Both the front and rear ratios become 100%4 (Mix mode setting)Tap "MIX mode" (ON) or (OFF) to select ON / OFF."OFF" :The EXP function of the 2nd CH and other settings are not mixed."ON" :The EXP function of the 2nd CH and other settings are mixed.5 (Trim mode setup)Tap "Trim mode" (ON) or (OFF) to select ON / OFF."OFF" :The trim of the 2nd CH is not mixed."ON" :The trim of the 2nd CH is mixed.6 When fi nished, return to the Mixing menu screen by pressing the HOME button twice.Adjustment buttons- Adjust with the and buttons.- Return to the initial value by tapping the [reset] buttons.Rear rate (Rear mix rate) 0~100 Initial value:100Setting- Tap (ON) / (OFF).Setting- Tap (ON) / (OFF).The dial select function can control the drive ratio with digital dial or digital trim.(page 66) Dial / Trim Setting As this function drives 2 separate motor controllers simultaneously, a mutual load is ap-plied. Use this function carefully so that the motor controllers are not damaged.Futaba will not be responsible for motor controller, motor, and other vehicle trouble due to use of this function.Note:](https://usermanual.wiki/Futaba/T7PX-24G.User-Manual-P116-192/User-Guide-3526470-Page-1.png)
![Home screen Menu screen Menu-2Menu-1Mixing menu CPS mixing Display the current drive mode.118FunctionCPS Mixing (1, 2, 3 ) CPS Mixing (1, 2, 3 ) This function controls the Futaba CPS-1 channel power switch. Normally, when using the CPS-1 unit to light the vehicle dress-up and other illumination (LED) the CPS-1 unit with LED connected is connected to a vacant switch channel and the LEDs are turned on and off by switch while the vehicle is running. However, when the CPS mixing function is used, the LED can be turned on and off and À ashed in step with steering and throttle operation, as well as being turned on and off by switch. The À ashing speed (cycle) can also be set. For in-stance, the LED can be À ashed as a brake light by throttle brake side operation. Three lines of CPS mixing can be used.The CPS-1 unit does not operate in SR mode. When using with the T - FHSS SR sys-tem, connect it to the channel of the normal mode.The mixing function is assigned to auxiliary channels used by other mixing cannot be used. When the number of channels is insuf¿ cient, cancel the other mixing. (Preparation)- CPS-1 connects to the receivers auxiliary channel.- When the LEDs are turned on and off by switch, use the func-tion select switch function (page 69) to set the switch to be used.- From the CPS Mixing screen, tap [CPS Mixing 1] / [CPS Mix-ing 2] or [CPS Mixing 3] to display the setting screen. Dual ESC mixing adjustment1 (Function ON/OFF)Tap "Mixing" (ON) or (OFF) to select ON / OFF."OFF" :Mixing function OFF"ON" :Mixing function ONSetting- Tap (ON) / (OFF).](https://usermanual.wiki/Futaba/T7PX-24G.User-Manual-P116-192/User-Guide-3526470-Page-2.png)
![*Shows the ON/OFF stateAdjustment buttons- Adjust with the [+] and [-] but-tons.- Return to the initial value by tapping the [reset] buttons.Cycle speed amount 1~100 Initial value: 50119FunctionCPS Mixing (1, 2, 3 ) Setting- Tap operation mode.Setting- Tap control mode.2 (Channel setup)The channel list screen used for the front ESC channel is displayed. Tap the auxiliary chan-nel that connected the front ESC channel.- When all channels are in use, a screen saying "No assignable channel" is displayed, please turn off other mixing and make an unused channel. You can check the mixing used on the channel setting screen (page 75).3(Control system setup)Tap the [Control]. The mode list appears on the CP-1 mix-ing menu screen, and tap from the list and select the control mode. To cancel, tap [Cancel]."Mixing Switch" : ON/OFF by switch set at the CPS mixing"Steering neutral" : ON at steering neutral"Steering endpoint" : ON at both sides of steering"Throttle neutral" : ON at throttle neutral"Throttle forward" : ON at throttle forward side"Throttle brake" : ON at throttle back (brake) side"Throttle neutral & brake" : ON at throttle neutral and back (brake) sides4 (ON / OFF switching position selection)Tap the value button of the [ON/OFF point]. Value input buttons appear on the screen. Use the [+] and [-] buttons to adjust the operation point. Since the ON/OFF state is displayed at the right side of the "Status", setting can be confirmed while operating the function to be controlled (for example, throttle). 5 (Operation mode setup)Tap the [Operation mode]. The mode list appears on the CP-1 mixing menu screen, and tap from the list and select the Operation mode. To cancel, tap [Cancel]."ON/OFF" : Normal ON/OFF type"Flash" : Flashing display6 (Flashing cycle setting)When "Operation mode" is set to "Flash" the "Cycle speed" can be set to preferred setting. Tap the value button of the [Cycle speed]. Value input buttons appear on the screen. Use the [+] and [-] buttons to adjust the cycle speed amount.Adjustment buttons- Adjust with the and buttons.- Return to the initial value by tapping the [reset] buttons.ON/OFF position 5 ~ 95 Initial value:507 When finished, return to the Mixing menu screen by pressing the HOME button twice.](https://usermanual.wiki/Futaba/T7PX-24G.User-Manual-P116-192/User-Guide-3526470-Page-3.png)
![Adjustment buttons- Adjust with the [+] and [-] but-tons.- Return to the initial value by tapping the [reset] buttons.Forward / backward rate -100~+100 Initial value: +100Adjustment buttons- Adjust with the [+] and [-] but-tons.- Return to the initial value by tapping the [reset] buttons.Left / Right travel -100~+100 Initial value: +100121FunctionTank MixingSetting- Tap (ON) / (OFF).2 (Limit ON / OFF)It is a function to limit the maximum opera-tion amount of the steering and throttle channel so that it does not exceed the limit by the influence of the mixing amount..Tap "Limit" (ON) or (OFF) to select ON / OFF.“OFF” :Limit function OFF“ON” :Limit function ON3 (Forward / backward rate adjustment)Tap the value button of the [Forward] or [Bsck]. Value input buttons appear on the screen. Use the [+] and [-] buttons to adjust the forward or reverse speed.- The throttle channel and the steering channel operate in conjunction with each other, and by operating the trigger to the high side, the car body advances at the [Forward] rate. When the trigger is operated to the brake side, it operates at the [Bsck] rate.4 (Left / Right side travel adjust)Tap the value button of the [Left] or [Right]. Value input buttons appear on the screen. Use the [+] and [-] buttons to adjust the left or right side travel amount.- When the throttle channel and the steering channel work in conjunction, when operating the steering wheel to the right, the car body turns to the right at the [Right] rate the pivotal turn. If you operate to the left, the car will turn to the left at the [Left] rate the pivotal turn.5 When finished, return to the Mixing menu screen by pressing the HOME button twice.If you manipulate the trigger to the high side and operate the steering wheel to the right, the body will turn right at the rate of [forward], [right].If you manipulate the trigger to the high side and operate the steering wheel to the left, the body turns to the left at the rate of [forward], [left].Operating the steering wheel while operating the trigger to the brake side will operate the same as the forward side in the reverse direction.When steering and trigger are operated at the same time.](https://usermanual.wiki/Futaba/T7PX-24G.User-Manual-P116-192/User-Guide-3526470-Page-5.png)
![123FunctionProgram, Mixing (1, 2, 3, 4, 5)(Preparation)- Use the switch select function (page 69) to select the switch. (as desired)- From the Program Mixing screen Tap [Program Mixing 1] - [Program Mixing 5] to use to move to the setting screen.1 (Function ON/OFF)Tap [1/2] at the upper right of the screen to display page 2.Tap "Mixing" (ON) or (OFF) to select ON / OFF."OFF" :Mixing function OFF"ON" :Mixing function ON2 (Master / Slave channel setup)Tap the [Master] or [Slave], and the channel setting screen will be displayed. Tap on that channel to select. To cancel, tap [Close].Program composite adjustment3 (Mix mode setting)Tap "MIX mode" (ON) or (OFF) to select ON / OFF.“OFF” :The EXP function of the 2nd CH and other settings are not mixed.“ON” :The EXP function of the 2nd CH and other settings are mixed.4 (Trim mode setup)Tap "Trim mode" (ON) or (OFF) to select ON / OFF."OFF" :The trim of the 2nd CH is not mixed."ON" :The trim of the 2nd CH is mixed.Setting- Tap (ON) / (OFF).For S-FHSS (analog) system, 1 to 7 chan-nels are displayed.Setting- Tap (ON) / (OFF).Setting- Tap channel.](https://usermanual.wiki/Futaba/T7PX-24G.User-Manual-P116-192/User-Guide-3526470-Page-7.png)
![EXP curve VTR curve CurveAdjustment buttons- Adjust with the [+] and [-] but-tons.- Return to the initial value by tapping the [reset] buttons.Left / Forward / A side rate -120~0 ~+120 Initial value: +50Adjustment buttons- Adjust with the [+] and [-] but-tons.- Return to the initial value by tapping the [reset] buttons.Right / Blake / B side rate -120~0 ~+120 Initial value: +50124FunctionProgram, Mixing (1, 2, 3, 4, 5)5 (Left, Forward or A side mixing amount adjustment)Tap the value button of the "Rate" [Left], [Forward] or [Rate A] . Value input buttons appear on the screen, adjust each of the left, forward or A steering angles using the [+] or [-] button.6 (Right, brake or B side mixing amount adjustment)Tap the value button of the "Rate" [Right], [Brake] or [Rate B] . Value input buttons appear on the screen, adjust each of the right, brake, or rate B steering angles using the [+] or [-] button.7 (Curve setting)"EXP / VTR / Curve" mixing can be set from master channel to slave channel. For details on how to set each curve, please read the steering curve and the throttle curve (pages 78 to 83).8 When finished, return to the Mixing menu screen by pressing the HOME button twice.](https://usermanual.wiki/Futaba/T7PX-24G.User-Manual-P116-192/User-Guide-3526470-Page-8.png)
![Home screen Menu screen Menu-2Menu-1 mixing125FunctionTilt MixingTilt Mixing Tilt mixing uses an outboard engine and applies bidirectional mixing from rudder to steady to Àap and from Àap to rudder so that with a boat, rudder operation and tilt mixing opera-tion can be performed 2 servos.Tilt mixing can be performed by rudder operation, by steering wheel and Àap channel.Steering end point function, curve function, speed function, or D/R function setup also effects Àap channel operation. However, even if set, steering reverse function setup does not reverse the Àap channel.Effect of the set value of other functions on tilt mixingThe mixing function is assigned to auxiliary channels used by other mixing cannot be used. When the number of channels is insuf¿cient, cancel the other mixing.(Preparation)- Use the "Trim/dial select" function to select the flap channel operation dial. (page 662)1 (Function ON/OFF)Tap [1/2] at the upper right of the screen to display page 2.Tap "Mixing" (ON) or (OFF) to select ON / OFF."OFF" :Mixing function OFF"ON" :Mixing function ONProgram composite adjustmentSetting- Tap (ON) / (OFF).](https://usermanual.wiki/Futaba/T7PX-24G.User-Manual-P116-192/User-Guide-3526470-Page-9.png)
![Adjustment buttons- Adjust with the [+] and [-] but-tons.- Return to the initial value by tapping the [reset] buttons.Mixing amount (Rudder to Flap) -100~+0~+100 Initial value: +100Mixing amount (Flap to Rudder) -100~+0~+100 Initial value: -100126FunctionTilt Mixing3 (Flap rate check and adjustment)Select the "Flap" by (JOG) button up or down operation, and adjust the fl aps by [+] or [-] operation.4 (Rudder to Flap mixing amount adjustment)Tap the value button of the "Rudder to Flap", Value input but-tons appear on the screen, and use the [+] and [-] buttons to adjust the mixing amount.“+” :Operate in same direction as steering“-” :Operate in opposite direction of steering5 (Flap to Rudder mixing amount adjustment)Tap the value button of the "Flapto Rudder", Value input but-tons appear on the screen, and use the [+] and [-] buttons to adjust the mixing amount.“+” :Operate in same direction as auxiliary channel“-” :Operate in opposite direction of auxiliary channel2 (Channel setup)The channel list screen used for the gain steering channel is displayed. Tap the auxiliary channel that connected the gain steering channel.- When all channels are in use, a screen saying "No assignable channel" is displayed, please turn off other mixing and make an unused channel. You can check the mixing used on the channel setting screen (page 75).For S-FHSS (analog) system, 1 to 7 chan-nels are displayed.If there is no assignable channel, tap [Close]. Turn off other mixing and make assignable channels.6 When fi nished, return to the Mixing menu screen by pressing the HOME button twice.The mixing rate amount can be controlled with digital dial or digital trim, using the dial select function.(page 66) Dial / Trim Setting](https://usermanual.wiki/Futaba/T7PX-24G.User-Manual-P116-192/User-Guide-3526470-Page-10.png)
![Alarm time OFF, 1 ~ 99 minutes Initial value: 5 minutes - Adjust with the [+] and [-] but-tons. - Return to the initial value by tapping the [reset] buttons.Pre-alarm time OFF, ON Initial value: OFF - Tap (ON) / (OFF).Grip vibrator type (pattern) Inhibit(Off), Type1,2,3 Initial value: Inhibit - Tap (ON) / (OFF).Start / StopStatus displayTimer reset130Function(Preparation)Select the “Up timer” from the timer type list and tap.1 (Alarm time setting)Tap the value button of the "Alarm time". Value input buttons appear on the screen. use the [+] and [-] buttons to set the time amount.Tap [Vibrate] and select the vibration pat-tern of the alarm from 3 types of patterns and disable (OFF).(Pre-alarm setting)Tap (ON) or (OFF) of pre-alarm and select ON / OFF.2 (Timer start/stop operation)When the switch (Timer start) assigned by switch select function is pressed, the timer starts. When you press the switch (Timer start) or [Start] / [Reset] on the screen dur-ing timer operation, the timer stops. - Linking only start to the throttle triggerTap [OFF] of the trigger to display [Ready] and wait for the trigger operation. When you operate the trigger to the forward side, the timer starts. Stop is the same as when starting with a switch.3 (Timer reset operation)With the timer stopped, press the switch (timer reset) set by the Switch setting func-tion, or tap [Reset] on the screen. The timer is reset with the beeping sound.Using the Up timerBrake Mixing](https://usermanual.wiki/Futaba/T7PX-24G.User-Manual-P116-192/User-Guide-3526470-Page-14.png)
![Alarm time OFF, 1 ~ 99 minutes Initial value: 5 minutes - Adjust with the [+] and [-] but-tons. - Return to the initial value by tapping the [reset] buttons.Pre-alarm time OFF, ON Initial value: OFF - Tap (ON) / (OFF).Grip vibrator type (pattern) Inhibit(Off), Type1,2,3 Initial value: Inhibit - Tap (ON) / (OFF).Start / StopStatus displayTimer reset131FunctionBrake Mixing(Preparation)Select the "Fuel down timer” from the timer type list and tap.1 (Alarm time setting)Tap the value button of the "Alarm time". Value input buttons appear on the screen. use the [+] and [-] buttons to set the time amount.Tap [Vibrate] and select the vibration pat-tern of the alarm from 3 types of patterns and disable (OFF).(Pre-alarm setting)Tap (ON) or (OFF) of pre-alarm and select ON / OFF.2 (Timer start/stop operation)When the switch (Timer start) assigned by switch select function is pressed, the timer starts. When the switch ("Timer start") is pressed while the timer is operating, the timer is re-set and simultaneously restarted. (Restart)When you press the [Reset] on the screen during timer operation, the timer stops. - Linking only start to the throttle triggerTap [OFF] of the trigger to display [Ready] and wait for the trigger operation. When you operate the trigger to the forward side, the timer starts. Stop is the same as when starting with a switch.3 (Timer reset operation)With the timer stopped, press the switch (timer reset) set by the Switch setting func-tion, or tap [Reset] on the screen. The timer is reset with the beeping sound.Using the fuel down timer](https://usermanual.wiki/Futaba/T7PX-24G.User-Manual-P116-192/User-Guide-3526470-Page-15.png)
![Alarm time OFF, 1 ~ 99 minutes Initial value: 5 minutes - Adjust with the [+] and [-] but-tons. - Return to the initial value by tapping the [reset] buttons.Pre-alarm time OFF, ON Initial value: OFF - Tap (ON) / (OFF).Grip vibrator type (pattern) Inhibit(Off), Type1,2,3 Initial value: Inhibit - Tap (ON) / (OFF).Start / StopStatus displayTimer reset132FunctionBrake Mixing(Preparation)Select the "Lap timer" from the timer type list and tap.1 (Alarm time setting)Tap the value button of the "Alarm time". Value input buttons appear on the screen. use the [+] and [-] buttons to set the time amount.Tap [Vibrate] and select the vibration pat-tern of the alarm from 3 types of patterns and disable (OFF).(Pre-alarm setting)Tap (ON) or (OFF) of pre-alarm and select ON / OFF.2 (Timer start operation)Perform the start and lap count operations with the switch ("Timer start") assigned by function select switch function.- Linking only start to the throttle triggerTap [OFF] of the trigger to display [Ready] and wait for the trigger operation. When you operate the trigger to the forward side, the timer starts. Stop is the same as when starting with a switch. 3 (Timer stop and lap reset operation)When the lap count switch or ("Timer re-set") switch is pressed after the time set by "Alarm" has elapsed and the lap time, total time, and average lap time are saved and checked. (Lap list page 134) If the switch ("Timer reset") set by switch setting func-tion is pressed, the timer is reset.When a switch is not set, tap [Reset] on the screen. The timer is reset with the beeping sound.Using the lap timer](https://usermanual.wiki/Futaba/T7PX-24G.User-Manual-P116-192/User-Guide-3526470-Page-16.png)
![Alarm time OFF, 1 ~ 99 minutes Initial value: 5 minutes - Adjust with the [+] and [-] but-tons. - Return to the initial value by tapping the [reset] buttons.Pre-alarm time OFF, ON Initial value: OFF - Tap (ON) / (OFF).Grip vibrator type (pattern) Inhibit(Off), Type1,2,3 Initial value: Inhibit - Tap (ON) / (OFF).Navi alarm time (NAVI) OFF, 1 ~ 99 seconds Initial value: 3 secondsStart / StopStatus displayTimer reset133FunctionBrake Mixing(Preparation)Select the "Lap navigate timer" from the timer type list and tap.1 (Alarm time setting)Tap the value button of the "Alarm time". Value input buttons appear on the screen. use the [+] and [-] buttons to set the time amount.Tap [Vibrate] and select the vibration pat-tern of the alarm from 3 types of patterns and disable (OFF).(Pre-alarm setting)Tap (ON) or (OFF) of pre-alarm and select ON / OFF.(Lap navigation time setting)Tap the value button of the "Lap navi". Value input buttons appear on the screen. use the [+] and [-] buttons to set the time amount.2 (Timer start / navigation restart operation)When the switch ("Timer start") assigned by switch select function is pressed, the timer starts. - Linking only start to the throttle triggerTap [OFF] of the trigger to display [Ready] and wait for the trigger operation. When you operate the trigger to the forward side, the timer starts. Stop is the same as when starting with a switch. When your own lap time is less than the target time and the lap counts overlap, the lap navigation alarm timing is too big. The alarm timing can be corrected by pressing the switch ("Timer start") during measurement.3 (Timer stop / reset operation)Press the switch ("Timer reset") set by the Switch setting function, or tap [Reset] on the screen. The timer is stops. With the timer stopped, press the switch ("Timer reset") set by the Switch setting function, or tap [Reset] on the screen. The timer is reset with the beeping sound.Using the lap navigate timer](https://usermanual.wiki/Futaba/T7PX-24G.User-Manual-P116-192/User-Guide-3526470-Page-17.png)
![Home screen Menu screen Accessory menu screen Timer 134FunctionLap listCall Lap list when checking the lap memory data (each lap time) memorized by lap timer (page 132 ) operation.- After the lap timer is started, the lap time is sequentially memorized at each switch opera-tion.-The total time and average time are displayed. The faster time is displayed in red charac-ters.-Lap time data is saved in each model data.-Up to 80 laps can be saved.-If the lap timer is reset, the lap list is also cleared.Lap List1 (Lap memory check)The lap time list displays 40 laps per page and 80 laps maximum on 2 pages. If there is a list on page 2, tap [1/2] / [2/2] at the upper right of the screen to change the display of the page.2 When finished, return to the Accessory menu screen by pressing the HOME button.Using the lap memory](https://usermanual.wiki/Futaba/T7PX-24G.User-Manual-P116-192/User-Guide-3526470-Page-18.png)
![136FunctionS.Bus Servo (Preparation)- Connect the T7PX and S.BUS or S.BUS2 servo in accordance with the connection dia-gram shown on page 135.- Connect the battery to a non-high voltage(HV) support S.BUS/S.BUS2 servo.1 Turn power on the transmitter. "S.Bus servo" menu is displayed referring to the map of page135.2 (S.BUS/S.BUS2 servo read)Execute this function to read the connected servo type and the data currently set at the servo. Tap the [Read]. The confirmation screen will be displayed. To execute, tap [Yes] to hear an electronic sound and finish setting. To cancel, select [No] and touch it.-"Reading succeeded" is displayed on the screen and the servo’s ID cord and currently set contents are read.- If "Failed" is displayed on the screen, communication with the servo is not being performed normally. Check the T7PX and servo connection to servo and repeat [Read]. (Connect the battery to a non-high volt-age(HV) support servo.)3 (Writing to S.BUS/S.BUS2)Execute this function to write the setting data to servo. See pages 138 to139 for the setting data contents.Tap the [Write]. The confirmation screen will be displayed. To execute, tap [Yes] to hear an electronic sound and finish setting. To cancel, se-lect [No] and touch it.-"Writing succeeded" is displayed on the screen and the setting data is written to servo.- If "Failed" is displayed on the screen, communication with the servo is not being performed normally. Check the T7PX and servo connection to servo and repeat [Write]. (Connect the battery to a non-high voltage(HV) support servo.)4 (Initialization)Write the factory set servo setting data to the con-nected servo. Tap the [Reset]. The confirmation screen will be displayed. To execute, tap [Yes] to hear an electronic sound and finish setting. To can-cel, select [No] and touch it.-"Writing succeeded" is displayed on the screen and the setting data is written to servo.- If "Failed" is displayed on the screen, communication with the servo is not being performed normally. Check the T7PX and servo connection to servo and repeat "Write". (Connect the battery to a non-high voltage(HV) support servo.)Using the S.Bus servo function](https://usermanual.wiki/Futaba/T7PX-24G.User-Manual-P116-192/User-Guide-3526470-Page-20.png)
![137FunctionS.Bus Servo1 The type and data of the loaded servo are displayed. Since there are two setting items, change the page as follows.1 (Writing to servo)Tap [SR mode] or [Normal mode] of SR mode setting. A confirmation screen of "Notes on SR setting" is displayed, so read carefully and tap [Normal mode] or [SR mode].- When [Normal mode] is selected, "Writing succeeded" is displayed on the screen, and the setting data is writ-ten to the servo.- If "Failed" is displayed, communication with the servo is not performed normally. Check the connection between the T7PX and the servo, and then execute the write operation again.2 (When SR mode is selected by writing to servo)In the confi rmation screen of "Notes on SR setting", tap [SR mode], the screen for selecting the SR type is dis-played. Three types with different feeling are prepared. (Please repeat the test and choose the type. )- "Writing succeeded" is displayed on the screen and the setting data is written to the servo. If "Failed" is displayed, communication with the servo is not performed normally. Check the connection between the T7PX and the servo, and then execute the [Write] operation again.- For the servo set to SR mode, affi x the attached SR label so that the mode can be recog-nized.Display data listSR mode setting When the connected servo type is not compatible with the SR mode, "Unsup-ported Normal mode" is displayed- Do not plug in or disconnect servos, or connect other servos while keeping the screen where data was read by [Read]. Be sure to connect the servo in the state where [Write] or [Reset] is ¿ nished, or press the Home button to access the accessory menu screen.- The loaded data can not be written to another servo. The type of servo and the set SR type are dis-played. Do not connect absolutely to the S. BUS channel of all receivers for the servo set to SR mode. The servo will fail.](https://usermanual.wiki/Futaba/T7PX-24G.User-Manual-P116-192/User-Guide-3526470-Page-21.png)
![138FunctionS.Bus Servo1 On the setting screen of each function, if you tap the item to be set, [-] [reset] [+] will be dis-played at the bottom of the screen, tap the [-] [+] on the panel Set. Tap[Reset] to return to the initial value. There are items with no [reset]. In case of selection type, data is switched by tapping an item.IDDisplays the ID of the servo whose param-eters are to be read. It cannot be changed.Dead bandThe dead band angle at stopping can be specified.[Relationship between dead band set val-ue and servo operation]Small - Dead band angle is small and the servo is immediately operated by a small signal change.Large - Dead band angle is large and the servo does not operate at small signal changes.(Note) If the dead band angle is too small, the servo will operate continuously and the current consumption will increase and the life of the servo will be shortened.DamperThe characteristic when the servo is stopped can be set.When smaller than the standard value, the characteristic becomes an overshoot character-istic. If the value is larger than the standard value, the brake is applied before the stop posi-tion.Especially, when a large load is applied, overshoot, etc. are suppressed by inertia and hunt-ing may occur, depending on the conditions. If hunting (phenomena which cause the servo to oscillate) occurs even though the Dead Band, Stretcher, Boost and other parameters are suitable, adjust this parameter to a value larger than the initial value.[Relationship between damper set value and servo operation]Small - When you want to overshoot. Set so that hunting does not occur.Large - When you want to operate so that braking is not applied. However, it will feel like the servo response has worsened.(Note) If used in the hunting state, not only will the current consumption increase, but the life of the servo will also be shortened.SmootherThis function makes servo operation smooth. Set it according to your taste. Normally set it to "ACT". Set it to "INH" when want especially quick operation. When the smoother func-tion was set to "ACT" and the servo was operated the distance up to the target position is changed in steps so movement is smooth.StretcherThe servo hold characteristic can be set. The torque which attempts to return the servo to the target position when the current servo position has deviated from the target position can be adjusted.S.BUS function setup](https://usermanual.wiki/Futaba/T7PX-24G.User-Manual-P116-192/User-Guide-3526470-Page-22.png)
![139FunctionS.Bus ServoThis is used when stopping hunting, etc., but the holding characteristic changes as shown below.[Relationship between stretcher and servo operation]Small - Servo holding force becomes weaker.Large - Servo holding force becomes stronger.(Note) When this parameter is large, the current consumption increases.Boost/Boost (ON/OFF)INH : It is the boost ON at the time of low-speed operation. (In the case of usual)ACT : It is always the boost ON. (When quick operation is hope).The minimum current applied to the internal motor when starting the servo can be set. Since a small travel does not start the motor, it essentially feels like the dead band was expanded. The motor can be immediately started by adjusting the minimum current which can start the motor.[Relationship between boost set value and servo operation]Small - Motor reacts to a minute current and operation becomes smooth.Large - Initial response improves and output torque increases. However, if the torque is too large, operation will be-come rough.ChannelThis is the S.BUS system channel assigned to the servo. When connected to the receiver S-BUS2 connector as an S.BUS system, the channel used by the transmitter is assigned. When the normal receiver channel is used, channel setting is unnecessary.ReverseThe direction in which the servo rotates can be changed.Soft StartRestricts operation in the specified direction the instant the power is turned on. By using this setting, the first initial movement when the power is turned on slowly moves the servo to the specified position.NeutralThe neutral position can be changed. When the neutral offset is large value, the servo’s range of travel is restricted on one side.Stop ModeThe state of the servo when the servo input signal is lost can be specified. The “Hold” mode setting holds the servo in its last commanded position even if using AM or FM system.SpeedSpeeds can be matched by specifying the operating speed. The speed of multiple ser-vos can be matched without being affected by motor fluctuations. This is effective for load torques below the maximum torque.However, note that the maximum speed will not be exceed what the servo is capable of even if the servos operating voltage is increased.Travel [Left] / [Right]The maximum left and right travels centered about the neutral position can be set indepen-dently.](https://usermanual.wiki/Futaba/T7PX-24G.User-Manual-P116-192/User-Guide-3526470-Page-23.png)
![141FunctionMC Link (ESC Link)(Preparation)-Connect the T7PX and ESC in accordance with the connection diagram shown on page 140.-Connect the battery to ESC.1 Turn power on the transmitter. "MC link" menu is displayed referring to the map of page 140. Set the FET amp power switch to the ON position.2 (ESC read)Execute this function to read the connected ESC type and the data currently set at the ESC. Tap the [Read]. The confirmation screen will be dis-played. To execute, tap [Yes] to hear an electronic sound and finish setting. To cancel, select [No] and touch it.- "Reading succeeded" is displayed on the screen and the ESC type and currently set contents are read.- If "Failed" is displayed on the screen, communication with the ESC is not being performed normally. Check the T7PX and ESC connection and the battery connection to ESC and the ESC power switch and repeat [Read].3 (Writing to ESC)Execute this function to write the setting data to ESC. See pages 143 to 148 for the setting data con-tents.Tap the [Write]. The confirmation screen will be displayed. To execute, tap [Yes] to hear an electronic sound and finish setting. To cancel, select [No] and touch it.- "Writing succeeded" is displayed on the screen and the setting data is written to ESC.- If "Failed" is displayed on the screen, communication with the ESC is not being performed normally. Check the T7PX and ESC connection and the battery connection to ESC and the ESC power switch and repeat [Write]. - Different type ESC data cannot be written. If writing is attempted, "Failed" is displayed on the screen.4 (Initialization)Write the factory set ESC setting data to the con-nected ESC. Tap the [Reset]. The confirmation screen will be displayed. To execute, tap [Yes] to hear an electronic sound and finish setting. To can-cel, select [No] and touch it.- "Writing succeeded" is displayed on the screen and the setting data is written to ESC.- If "Failed" is displayed on the screen, communication with the ESC is not being performed normally. Check the T7PX and ESC connection and the battery connection to ESC and the ESC power switch and repeat [Write].Using the ESC Link function](https://usermanual.wiki/Futaba/T7PX-24G.User-Manual-P116-192/User-Guide-3526470-Page-25.png)
![142FunctionMC Link (ESC Link)-ESC is read referring to the explanation of page 139. 1 Tap the [Data list]. Depending on the ESC type, the setting items are different.If there are multiple pages, move the page as follows.Display data listMC940/960CR page 1950CR page 1601CR/850C page 1402CR page 1602CR/851C page 1401CR page 1 401CR/402CR page 2601CR/602CR/851C page 2 850C page 2950CR page 2 950CR page 3MC940/960CR page 2 MC940/960CR page 3 MC940/960CR page 4To page 1To page 1](https://usermanual.wiki/Futaba/T7PX-24G.User-Manual-P116-192/User-Guide-3526470-Page-26.png)
![148FunctionMC Link (ESC Link)When using in races in which the lead angle setting function is inhibited by the ESC, set "Lead angle use" to "INH". The "Lead angle use" setting has priority over "Turbo mode". If "Lead angle use" is set to "INH", the lead angle setting function can be turned off even if "Turbo mode" is set to "Tu rb o1" or "Tu r bo2".The MC940,960CR shows that the lead angle setting function is OFF ("0" timing) by blinking a LED.Turn on "Lead angle use"Lead angle use MC940,960CR :ACT/INHSame as Link software Lead Angle Use.This function is effective when Turbo Mode is Turbo1 or Turbo2 and sets whether or not lead angle is used. This setting has priority over the Turbo Mode setting. When using in races in which the lead angle function is inhibited by the ESC set this function to INH. INH : Lead angle function not used. ACT : Lead angle usedPoint A,B,C,D,E Lead angle MC940,960CR :0deg~59degSame as Link software Boost Angle.Point A,B,C,D,E Rotation MC940,960CR :0rpm~120,000rpmSame as Link software Boost Angle rpm.When "Lead Angle Use" is turned on the lead angle versus motor speed of the 5 points A to E can be set. The lead angle can be set up to 59 degrees in 1 degree increments.The "Lead angle" and "Point A, B, C, D, E Lead angle" relationship is shown on the graphs below. Graph [1] shows the relationship when the same value is set at "Points A, B, C, D, E Lead angle" of [1] and [2] and the "Lead angle" was set to "0" and graph [2] shows the rela-tionship when a value other than "0" was set at "Lead angle". As shown in the graphs, [2] is added to the "Points A, B, C, D, E Lead angle" set lead angle and [1] is added to the "Lead angle" set lead angle. For example, if "3" is set at Point A and "Lead angle" of [2] is set to "2, the actual Point A becomes 3+2=5 (deg). Since "Lead angle" of [A] is "0", the actual Point A also becomes 3+0=3 (deg).A B C D EABCDEA B C D EA基準進角BCDE1 (Lead angle ="0") Lead Angle(deg) 2 (Lead angle >"0") Lead Angle(deg)rpm rpm](https://usermanual.wiki/Futaba/T7PX-24G.User-Manual-P116-192/User-Guide-3526470-Page-32.png)
![Adjustment buttons- Adjust with the [+] and [-] but-tons.- Return to the initial value by tapping the [reset] buttons.149FunctionRoll Out ChartRoll Out ChartThis function is designed for pan cars. The roll out chart can be calculated from input val-ues for the number of teeth of the spur gear and pinion gear, and the tire diameter, and dis-played as a table.1 (Setting of step of the tire diameter input) Tap the value button of the [Step]. Value input buttons appear on the screen. Use the [+] and [-] buttons to set the step of input numerical value of tire diameter amount.- The step amount can be set in the range of 0.1 mm to 1.0 mm.2 (Setting of number of teeth of spur gear) Tap the value button of the [Super]. Value input buttons appear on the screen. Use the [+] and [-] buttons to set the spur gear. The roll out is then calculated, and the list is updated.3 (Setting of number of teeth of pinion gear) Tap the value button of the [Pinion]. Value input buttons appear on the screen. Use the [+] and [-] buttons to set the pinon gear. The roll out is then calculated, and the list is updated.3 (Setting of tire diameter) Tap the value button of the [Diameter]. Value input buttons appear on the screen. Use the [+] and [-] buttons to set the tire diameter. The roll out is then calculated, and the list is updated.4 When fi nished, return to the Accessory menu screen by pressing the HOME button.Use of Roll out chart functionHome screen Menu screen Accessory menu screen Roll out chart Setup item Pinion Sper Step Diameter](https://usermanual.wiki/Futaba/T7PX-24G.User-Manual-P116-192/User-Guide-3526470-Page-33.png)
![Home screen Menu screen Accessory menu screen Gear ratio chart Adjustment buttons- Adjust with the [+] and [-] but-tons.- Return to the initial value by tapping the [reset] buttons.150FunctionGear Retio ChartGear Retio Chart The Gear Retio Chart can be calculated from input values for the number of teeth of the spur gear and pinion gear, and secondary gear ratio, and displayed as a table.1 (Setting of number of teeth of spur gear) Tap the value button of the [Super]. Val-ue input buttons appear on the screen. Use the [+] and [-] buttons to set the spur gear. The roll out is then calculated, and the list is updated.2 (Setting of number of teeth of pinion gear) Tap the value button of the [Pinion]. Value input buttons appear on the screen. Use the [+] and [-] buttons to set the pinon gear. The roll out is then calculated, and the list is updated.2 (Setting of number of secondary gear ratio) Tap the value button of the [2nd gear ratio]. Value input buttons appear on the screen. Use the [+] and [-] buttons to set the 2nd gear ratio. The roll out is then calculated, and the list is updated.3 When fi nished, return to the Accessory menu screen by pressing the HOME button.Use of Roll out chart functionSetup item Pinion 2nd Gear ratio Sper](https://usermanual.wiki/Futaba/T7PX-24G.User-Manual-P116-192/User-Guide-3526470-Page-34.png)
![151FunctionHome Button SettingHome Button SettingYou can select the screen to display when you push the Home button on the Home screen, menu or user menu. You can not change the screen to display by push and holding the Home button from the menu screen or each function screen. - Push------------------Display menu screen or custom menu screen. - Long press-----------Trim lock or display the function screen of your choice.1 (Setting for push)Tap "Puah" [Menu] or [User menu] to select "Menu" / "User menu".2 (Setting for long press)Tap "long press".The function list appears on the home but-ton setting menu screen. Tap and select the function you want to use. To cancel, tap [Close].- Since there are multiple pages, tap the mark and move the page. 3 When finished, return to the Accessory menu screen by pressing the HOME button.How to set the home buttonHome screen Menu screen Accessory menu screen Home hutton setting](https://usermanual.wiki/Futaba/T7PX-24G.User-Manual-P116-192/User-Guide-3526470-Page-35.png)
![Adjustment buttons- Adjust with the [+] and [-] but-tons.- Return to the initial value by tapping the [reset] buttons.Setting- Tap (ON) / (OFF).154FunctionTelemetry :Receiver Battery VoltageThis function displays and sets the receiver power supply battery. The sensor sold separately does not have to be installed. The transmitter initial state voltage is also displayed. For a description of alarm setting when the voltage drops, see the description of the procedure on this page.TelemetryCurrent receiver battery voltageThe Speech function (ON/OFF)The minimum and maximum when powering ON are shown.Sets the limiter voltage(Voltage that sounds an alarm)Alarm/vibrator ON/OFF and type setting (The arrow indicates that an alarm is generated when the power supply voltage drops below the set value.)1 (Limit adjustment)Tap the [Limit]. Value input buttons appear on the screen.Use the [+] or [-] button to adjust the limit voltage.2 (Alarm function setup)Tap the [Alarm] type and select [Inhibit], [Buzzer]or [Voice]."Inhibit" :No audible alarm"Buzzer" :Audible alarm"Voice" :Voice alarm3 (Vibrator function setup)Tap the [Vibrator] type and select [Inhibit], [Type 1], [Type 2], or [Type 3]."Inhibit" :No active vibration"Type1" :Continuous vibration"Type2" :Intermittent vibration for a long time"Tyoe3" :Intermittent vibration for a short time4(Speech function setup)Tap the "Voice" (ON) or (OFF) to select ON / OFF."OFF" :No voice guide"ON" :Information loaded by voice5 When fi nished, return to the Telemetry screen by pressing the HOME button.Alarm and Vibrator function setupSetting- Tap alarm type. Inhibit/ Buzzer/ VoiceSetting- Tap Vibrator type. TInhibit/ Type 1/ Type 2/ Type 3 *The voice guide loading inter-val is set by sensor menu.Telemetry](https://usermanual.wiki/Futaba/T7PX-24G.User-Manual-P116-192/User-Guide-3526470-Page-38.png)
![Adjustment buttons- Adjust with the [+] and [-] but-tons.- Return to the initial value by tapping the [reset] buttons.Setting- Tap (ON) / (OFF).155FunctionTelemetry :The Drive Battery VoltageWith an external power supply, one voltage of the batteries (drive battery, servo power sup-ply battery, etc.) mounted separately in the chassis can be displayed at the transmitter. The receiver S.BUS2 connector is used to connect the SBS-01V sensor and the battery.* A drive battery sensor must be installed in the model car. Install and connect the sensor in accordance with the sensor instruction manual.Telemetry Current drive battery voltageThe Speech function (ON/OFF)The minimum and maximum when powering ON are shown.Sets the limiter voltage(Voltage that sounds an alarm)Alarm/vibrator ON/OFF and type setting (The arrow indicates that an alarm is generated when the power supply voltage drops below the set value.)1 (Limit adjustment)Tap the [Limit]. Value input buttons appear on the screen.Use the [+] or [-] button to adjust the limit voltage.2 (Alarm function setup)Tap the [Alarm] type and select [Inhibit], [Buzzer]or [Voice]."Inhibit" :No audible alarm"Buzzer" :Audible alarm"Voice" :Voice alarm3 (Vibrator function setup)Tap the [Vibrator] type and select [Inhibit], [Type 1], [Type 2], or [Type 3]."Inhibit" :No active vibration"Type1" :Continuous vibration"Type2" :Intermittent vibration for a long time"Tyoe3" :Intermittent vibration for a short time4(Speech function setup)Tap the "Voice" (ON) or (OFF) to select ON / OFF."OFF" :No voice guide"ON" :Information loaded by voice5 When fi nished, return to the Telemetry screen by pressing the HOME button.Alarm and Vibrator function setupSetting- Tap alarm type. Inhibit/ Buzzer/ VoiceSetting- Tap Vibrator type. TInhibit/ Type 1/ Type 2/ Type 3 *The voice guide loading inter-val is set by sensor menu.Telemetry](https://usermanual.wiki/Futaba/T7PX-24G.User-Manual-P116-192/User-Guide-3526470-Page-39.png)
![Adjustment buttons- Adjust with the [+] and [-] but-tons.- Return to the initial value by tapping the [reset] buttons.156FunctionTelemetry :RPMSpeed information from an SBS-01RM (telemetry rotation sensor) sold separately is dis-played and set at this screen. The speed of the engine, motor, etc. of the chassis while run-ning can be viewed at the transmitter. When the speed becomes higher (lower) than the set speed, it can be announced by an alarm and vibration.* A RPM sensor must be installed in the model car. Install and connect the sensor in accordance with the sensor instruction manual.Telemetry Current RPMThe Speech function (ON/OFF)The maximum when powering ON are shown.Gear ratioSets the limit speedUpper limit/ lower limit(Speed that sound an alarm)Alarm and vibrator ON/OFF and type setting (The arrow indicates that an alarm is generated when the speed drops below the set value and the arrow indicates that an alarm is generated when the speed exceeds the set value.)Telemetry1 (Gear ratioadjustment)Tap the [Gear ratio]. Value input buttons appear on the screen.Use the [+] or [-] button to adjust the Gear ratio.2 (Limit adjustment)Tap the " " [Limit] or " " [Limit]. Value input buttons appear on the screen.Use the [+] or [-] button to adjust the limit voltage.3 (Alarm and vibrator function setup)Tap the " " / "" [Alarm] type and select [Inhibit], [Buzzer]or [Voice]."Inhibit":No audible alarm/ "Buzzer":Audible alarm/ "Voice":Voice alarmTap the " " / "" [Vibrator] type and select [Inhibit], [Type 1], [Type 2], or [Type 3]."Inhibit" :No active vibration"Type1" :Continuous vibration"Type2" :Intermittent vibration for a long time"Tyoe3" :Intermittent vibration for a short time4(Speech function setup)Tap the "Voice" (ON) or (OFF) to select ON / OFF."OFF" :No voice guide"ON" :Information loaded by voice5 When fi nished, return to the Telemetry screen by pressing the HOME button.Alarm and Vibrator function setup *The voice guide loading inter-val is set by sensor menu.](https://usermanual.wiki/Futaba/T7PX-24G.User-Manual-P116-192/User-Guide-3526470-Page-40.png)
![Adjustment buttons- Adjust with the [+] and [-] but-tons.- Return to the initial value by tapping the [reset] buttons.Setting- Tap (ON) / (OFF).157FunctionTelemetry :TemperatureThis screen displays and sets the temperature information from an SBS-01T (telemetry temperature sensor) sold separately. The temperature of the engine, motor, amp, etc. of the chassis while running can be viewed at the transmitter. When the temperature becomes higher (lower) than the set value, it can be announced by an alarm and vibration.* A temperature sensor must be installed in the model car. Install and connect the sensor in accordance with the sensor instruction manual.Telemetry Current temperatureThe minimum and maximum the when powering ON are shown. Limit temperature setting (Temperature that sounds an alarm)Alarm and vibrator ON/OFF and type setting (The arrow indicates that an alarm is generated when the speed drops below the set value and the arrow indicates that an alarm is generated when the speed exceeds the set value.)Telemetry1 (Limit adjustment)Tap the " " [Limit] or " " [Limit]. Value input buttons appear on the screen.Use the [+] or [-] button to adjust the limit voltage.2 (Alarm and vibrator function setup)Tap the " " / "" [Alarm] type and select [Inhibit], [Buzzer]or [Voice]."Inhibit":No audible alarm/ "Buzzer":Audible alarm/ "Voice":Voice alarmTap the " " / "" [Vibrator] type and select [Inhibit], [Type 1], [Type 2], or [Type 3]."Inhibit" :No active vibration"Type1" :Continuous vibration"Type2" :Intermittent vibration for a long time"Tyoe3" :Intermittent vibration for a short time3 (Speech function setup)Tap the "Voice" (ON) or (OFF) to select ON / OFF."OFF" :No voice guide"ON" :Information loaded by voice4 When fi nished, return to the Telemetry screen by pressing the HOME button.Alarm and Vibrator function setupThe Speech function (ON/OFF)Setting- Tap alarm type. Inhibit/ Buzzer/ VoiceSetting- Tap Vibrator type. TInhibit/ Type 1/ Type 2/ Type 3 *The voice guide loading inter-val is set by sensor menu.](https://usermanual.wiki/Futaba/T7PX-24G.User-Manual-P116-192/User-Guide-3526470-Page-41.png)
![Adjustment buttons- Adjust with the [+] and [-] but-tons.- Return to the initial value by tapping the [reset] buttons.Setting- Tap (ON) / (OFF).159FunctionTelemetry1 (Limit adjustment)Tap the " " [Limit] or " " [Limit]. Value input buttons appear on the screen.Use the [+] or [-] button to adjust the limit voltage.2 (Alarm and vibrator function setup)Tap the " " / "" [Alarm] type and select [Inhibit], [Buzzer]or [Voice]."Inhibit":No audible alarm/ "Buzzer":Audible alarm/ "Voice":Voice alarmTap the " " / "" [Vibrator] type and select [Inhibit], [Type 1], [Type 2], or [Type 3]."Inhibit" :No active vibration"Type1" :Continuous vibration"Type2" :Intermittent vibration for a long time"Tyoe3" :Intermittent vibration for a short time3 (Speech function setup)Tap the "Voice" (ON) or (OFF) to select ON / OFF."OFF" :No voice guide"ON" :Information loaded by voice1(Reset operation)Tap the [Reset], the consumption capacity display is reset to 0. The consumption capacity from the time of reset is displayed until you reset it again. If you reset the consumption capacity by pressing the reset button of SBS-01C, the consumption capacity display on the transmitter is also reset.2 When finished, return to the Telemetry screen by pressing the HOME button.4 When finished, return to the Telemetry screen by pressing the HOME button. Unless the reset button of SBS-01C is pressed, the consumption capacity measured by SBS-01C is maintained and displayed as “integrated capacity” on the screen. If you wish to mea-sure the consumption capacity for one run, it is possible to reset the consumption capacity display on the transmitter by the next operation. However, the record of the integrated capac-ity of the SBS-01C main body cannot be reset by the function which resets the transmitter display.Alarm and Vibrator function setupReset consumption capacity displaySetting- Tap alarm type. Inhibit/ Buzzer/ VoiceSetting- Tap Vibrator type. TInhibit/ Type 1/ Type 2/ Type 3 *The voice guide loading inter-val is set by sensor menu.The reset operation on the transmitter resets the integrated capacity display on the T7PX. It does not reset the integrated capacity on the SBS-01C. The consumption capacity measurement range of SBS-01C is 32767mAh maximum. When this value is exceeded, the consumption capacity dis-play on the transmitter is also reset automatically. Depending on the timing, reset may occur during measurement. Therefore, make sure to reset the integrated capacity on the SBS-01C before the integrated capacity display reaches 32767mAh.](https://usermanual.wiki/Futaba/T7PX-24G.User-Manual-P116-192/User-Guide-3526470-Page-43.png)
![160FunctionTelemetryTelemetry :GPSWhen SBS-01G/02G (GPS sensor) sold separately is mounted on the car body, you can re-ceive radio waves from GPS satellites and display information on the position and speed of the car.* A GPS sensor must be installed in the model car. Install and connect the sensor in accordance with the sensor instruction manual.* When powered up, the SBS-01/02G begins to acquire GPS satellite data. This process can take several minutes. Please do not move the model during this process. During acquisition, the LED on the SBS-01/02G will blink green; after the satellite’s signals have been acquired, the LED will become solid green, and the GPS signal strength display on the transmitter will show three bars. Moving the model before the satellites are fully acquired will cause a delay in acquiring the satellite signal.* Since GPS satellites are basically used, accurate distances and speeds may not be displayed depending on the surrounding environment or the conditions of the course.Telemetry Current distanceCurrent speedThe maximum when powering ON are shown.* Tap the max display button to restart the measurement.The maximum when powering ON are shown.* Tap the max display button to restart the measurement.Tap the [Preset reference]. Sets the current car position as the starting point.Tap the [Preset reference]. Sets the current car position as the starting point.Alarm and vibrator ON/OFF and type setting (The arrow indicates that an alarm is generated when the minimum distance below the set value and the arrow indicates that an alarm is generated when the distance exceeds the set value.)Alarm and vibrator ON/OFF and type setting (The arrow indicates that an alarm is generated when the minimum speed below the set value and the arrow indicates that an alarm is generated when the speed exceeds the set value.)The Speech function (ON/OFF)The position of the pres-ent model is displayed.This indicates the receiving accuracy from a GPS Satel-lite. The Speech function (ON/OFF)-Upper side:Current distance and speed display.-Lower:This is a display of the maximum value of the measured distance and speed after turning on the transmitter power.* Tap the max display button to restart the mea-surement.](https://usermanual.wiki/Futaba/T7PX-24G.User-Manual-P116-192/User-Guide-3526470-Page-44.png)
![Adjustment buttons- Adjust with the [+] and [-] but-tons.- Return to the initial value by tapping the [reset] buttons.Setting- Tap (ON) / (OFF).161FunctionTelemetry1 (Limit adjustment)Tap the " " [Limit] or " " [Limit]. Value input buttons appear on the screen.Use the [+] or [-] button to adjust the limit voltage.2 (Alarm and vibrator function setup)Tap the " " / "" [Alarm] type and select [Inhibit], [Buzzer]or [Voice]."Inhibit":No audible alarm/ "Buzzer":Audible alarm/ "Voice":Voice alarmTap the " " / "" [Vibrator] type and select [Inhibit], [Type 1], [Type 2], or [Type 3]."Inhibit" :No active vibration"Type1" :Continuous vibration"Type2" :Intermittent vibration for a long time"Tyoe3" :Intermittent vibration for a short time3 (Speech function setup)Tap the "Voice" (ON) or (OFF) to select ON / OFF."OFF" :No voice guide"ON" :Information loaded by voice4 When finished, return to the Telemetry screen by pressing the HOME button.Alarm and Vibrator function setupSetting- Tap alarm type. Inhibit/ Buzzer/ VoiceSetting- Tap Vibrator type. TInhibit/ Type 1/ Type 2/ Type 3 *The voice guide loading inter-val is set by sensor menu.1 (reset operation)Since either the distance / speed screen can be used, tap [Reference position setting]. The distance is reset. After that, the distance from the point where resetting is done is displayed until tapping [Reference position setting] again.It takes a while for GPS to be measured after turning on the power. Please wait until the LED of the GPS sensor turns on green without moving the car body. If the distance display does not stabilize even after the green LED lights up, or if you set a new reference value for the place where the car body moved, reset the reference position.How to set the reference position](https://usermanual.wiki/Futaba/T7PX-24G.User-Manual-P116-192/User-Guide-3526470-Page-45.png)
![163FunctionSensor List1 (Start slot selection)Tap [Slot], the list of sensors that can be registered in the start slot will be displayed.Sensors that can not be changed are not displayed.2 (Sensor selection)From the sensor list, tap the sensor you want to register in the start slot. To set as an empty slot, tap [---------]. This completes the change.3 When finished, return to the Sensor list screen by pressing the HOME button.How to change start slot and set empty slotStart slot selection- Tap the slotSensor selection- Tap the sensor](https://usermanual.wiki/Futaba/T7PX-24G.User-Manual-P116-192/User-Guide-3526470-Page-47.png)
![Communication port. Cover165FunctionSensorSensor ReloadWhen using multiple sensors of the same type the sensors must be registered in the trans-mitter. Connect all the sensors to be used to the T7PX as shown in the ¿ gure at the right and register them by the following procedure. The ID of each sensor is registered in the transmitter.To load the sensor, connect all sensors to be used to the T7PX communication port as shown below. Power supply is unnecessary. Also, to clear all sensor registration, execute this [Reload] function without connecting sensor. The registration is cleared and all the slots in the sensor list are unregistered.All the sensors to be used are connected to the T7PX.Sensor Sensor Sensor 1 (Start slot selection)Tap the [Reload], The confi rmation screen will be displayed. To execute, tap [Yes] to hear an electronic sound and fi nish setting. To cancel, select [No] and touch it. If "Success" appears on the screen, reroad is complete.2 When fi nished, return to the Telemetry screen by pressing the HOME button.How to change start slot and set empty slot](https://usermanual.wiki/Futaba/T7PX-24G.User-Manual-P116-192/User-Guide-3526470-Page-49.png)
![Communication port. Cover166FunctionSensorSensor RegisterThis function registers additional sensors. Connect the sensor as shown in the ¿ gure and register as follows. The sensor ID is registered in the transmitter.This function is set when adding one telemetry sensor of the same type.Connecting S.BUS/S.BUS2 servo connector to the T7PX. Sensor (The battery is not necessary)Confi rm sensor connection1 (Start slot selection)Tap the [Register], The confi rmation screen will be displayed. To execute, tap [Yes] to hear an electronic sound and fi nish setting. To cancel, select [No] and touch it. If "Success" ap-pears on the screen, registration is complete. If registering a sensor that has already been registered is attempted, the message "Failed; The same sensor has been registered" will be displayed. If the message "Failed; The connected sensor is not ready." is displayed, check the sensor connection. If it is securely connected, the sensor or the transmitter may be faulty.2 When fi nished, return to the Telemetry screen by pressing the HOME button.How to change start slot and set empty slot](https://usermanual.wiki/Futaba/T7PX-24G.User-Manual-P116-192/User-Guide-3526470-Page-50.png)
![167FunctionSensorChange SlotThis procedure changes the slot number of one registered sensor. Connect the sensor as shown in the ¿gure (page 166), and change slot number.This function is set when using multiple telemetry sensors of the same type.1(Change)Tap the [Change slot]. The sensor details screen is displayed. Tap the [Read]. The confirma-tion screen will be displayed. To execute, tap [Yes] to hear an electronic sound and finish reading. To cancel, select [No] and touch it. If "Reading suceeded" appears and the current sensor information is displayed.2 (Number setting)Tap the value button of the [Start slot #]. Value input buttons appear on the screen. Use the [+] and [-] buttons to set the start slot number.3 Tap the [Write]. When "Writing suceeded" message is displayed, the number change is completed.Sensor slot changeSetting button Setting with the [+] and [-] but-tons.4 When finished, return to the Sensor screen by pressing the HOME button.](https://usermanual.wiki/Futaba/T7PX-24G.User-Manual-P116-192/User-Guide-3526470-Page-51.png)
![168FunctionSensorSpeech guide interval and log data interval settingYou can set the interval at which to read the voice guide of telemetry information and the interval at which log data is recorded.Telemetry meter display on home screenTelemetry information on the home screen, graphic meter can be displayed.1 (Setting of speech interval)Tap the value button of the [Speech in-terval]. Value input buttons appear on the screen. Use the [+] and [-] buttons to adjust the speech interval amount.1 (Function ON/OFF)Tap "Home screen" (ON) or (OFF) to select ON / OFF."OFF" :Telemetry meter not displaed"ON" :Telemetry meter display2 (Setting of logging interval)Tap the value button of the [Logging in-terval]. Value input buttons appear on the screen. Use the [+] and [-] buttons to adjust the logging interval amount.Setting intervalDisplay of telemetry meterAdjustment buttons- Adjust with the [+] and [-] but-tons.- Return to the initial value by tapping the [reset] buttons.Adjustment buttons- Adjust with the [+] and [-] but-tons.- Return to the initial value by tapping the [reset] buttons.Speech interval 0~ 30 sec Initial value: 0Logging interval 0~ 30 sec Initial value: 03 When finished, return to the Telemetry screen by pressing the HOME button.3 When finished, return to the Telemetry screen by pressing the HOME button.](https://usermanual.wiki/Futaba/T7PX-24G.User-Manual-P116-192/User-Guide-3526470-Page-52.png)
![169FunctionSensorTelemetry meter display settingsFive telemetry meters displayed on the home screen are displayed. You can select the sensor to display and set the range of display data. It can be set for each meter.Tap meter to set display range etc.Tap to select sensor to displayDisplay the screen to select the sensor to be displayed.When the sensor to be displayed can measure multiple data, select which data to display.In the case of a current sensor, for example, it is possible to select from current / voltage / consump-tion capacity, to select data to dis-play from a plurality of data.It is also possible to display all three data with separate meters.Tap the value button of the [Max.] and [Min]. Value input buttons ap-pear on the screen. Use the [+] and [-] buttons to adjust the upper limit and lower limit amount.Set the upper limit / lower limit displayed on the meter.Home screen](https://usermanual.wiki/Futaba/T7PX-24G.User-Manual-P116-192/User-Guide-3526470-Page-53.png)
![Home screen Menu screen Model menu screen Model selectModel #. M1~M40Model selection- Tap the [Model name]170FunctionModel SelectForty model data (model data for 40 R/C cars) can be saved in the T7PX transmitter and used when the relevant model data is called. However, models copied in the microSD card can not be used by directly calling from the card. Please copy it to the T7PX main unit when using it.Model SelectModel where green cursor is currently in useSince there are multiple pages, tap the mark and move the page. 1 (Model memory selection)You can choose from 8 models on 1 page and 40 models on 5 pages. Tap the mark at the bottom of screen to move the page.2 (Model selection executionTap the [Model name] to use, a confi rma-tion screen will be displayed saying "Are you sure?" To execute, tap [Yes], a beep sounds and the change is completed and the home screen is displayed. To cancel, tap [No] and tap.- If the model name of the home screen is changed, model selection is completed.3 When fi nished, return to the Model menu screen by pressing the HOME button.Using the model selection function](https://usermanual.wiki/Futaba/T7PX-24G.User-Manual-P116-192/User-Guide-3526470-Page-54.png)
![Home screen Menu screen Model menu screen Model copyCopy source Tap to select from the list171FunctionModel copyThe contents of the model memory can be copied to another model memory. The contents can also be saved or stored on a microSD card for copying to another T7PX.Model Copy1 (Copy source model selection)You can choose from 8 models on 1 page and 40 models on 5 pages. Tap the mark at the bottom of screen to move the page.2 (Model selection executionTap the "Copy from" [model name], select the model list so it will tap. The source model is selected and the model list is closed. The list is the same design as the model select and the way of moving the page is the same. If a microSD card is in-stalled in the T7PX main unit, a button for selecting either the model inside the T7PX main unit or the model inside the microSD card will be displayed, so tap to select it. To cancel, press the Home button to return to the model copy screen. Model copyingTap to select the model of the T7PX main body or the model inside the SD card.Tap to view the model in the SD card](https://usermanual.wiki/Futaba/T7PX-24G.User-Manual-P116-192/User-Guide-3526470-Page-55.png)
![Copy execution Tap the [Copy]Copy destination Tap to select from the list172FunctionModel copy3 (Copy destination model selection)Tap the "Copy to" [model name], select the model list so it will tap. The source model is selected and the model list is closed. -The model currently in use cannot be selected.-Since the copy destination cannot be overwritten when it is in a microSD card, a models list is not dis-played and the model is saved directly to the microSD card.4 (Copy execution)Tap the [Copy], The confirmation message "Are you sure" appears. To execute copy, tap [Yes] and to cancel copy, select [No]. When the copy destination model name becomes the same name as the copy source, copying is complete.5 When finished, return to the Model menu screen by pressing the HOME button.Model datamicroSD card storage destinationWhen a microSD card is installed in the T7PX, a folder called “Futaba” is created, and folders called “LOG” and “MODEL” are created in it. The “MODEL” folder contains the model data. When the T7PX model data is copied, and the copy source data is select-ed from the model data stored in the microSD, a model list like that shown at the left is displayed.](https://usermanual.wiki/Futaba/T7PX-24G.User-Manual-P116-192/User-Guide-3526470-Page-56.png)
![Select / determine character Select a character, tap it to de-termine the characterName cursor movement Use the [ ] / [ ] tap to move the cursor. Also, when you de-cide a character, when the cur-sor position of the model name moves to the right, the cursor position of the model name moves to the rightHome screen Menu screen Model menu screen Model copy173FunctionModel NameThis function allows you to assign a ten character name to each model memory.Model NameMove cursor Deletion and cancellation of characters (Undo)Tap to select charactersSelection of alphabet / number / "kana"1 (Moving the cursor to the character you want to change.)In the model name, tap [ ], [ ] to move the cursor and select the character of the model name you want to set or change. A vertical line cursor is displayed before the selected character.2 (Selection of characters to use)Select the character to use from the character list. When you decide the character to use, tap it. The character is deter-mined and the character string of the model name moves to the right. If you tap [BS], the left character of the vertical line cursor will be deleted. To redo, tap [Undo].3 When fi nished, return to the Model menu screen by pressing the HOME button.Setting the model name and user name](https://usermanual.wiki/Futaba/T7PX-24G.User-Manual-P116-192/User-Guide-3526470-Page-57.png)
![Home screen Menu screen Model menu screen Model selectDelete execution Tap the [model data]174FunctionModel Delete (Model saved on microSD card)This function deletes model data saved on the microSD card.Model deletion is displayed on the menu only when microSD card is set in the T7PX card slot.Model Delete (Model saved on microSD card)1 (selection of model data)If the number of models that does not fit on one page is memorized, tap [1/2] in the upper right corner to move the page.If there are 2 pages, it will be displayed as [1/2] / [2/2], if there are 5 pages, it will be displayed as [1/5] to [5/5].2 (execution of model deletion)Tap the model you want to delete. A confir-mation message "Are you sure?" appears. Tap [Yes] to execute the deletion, or [No] to cancel."Deleting succeded" is displayed and dele-tion is completed.3 When finished, return to the Model menu screen by pressing the HOME button.How to delete model data in microSD card](https://usermanual.wiki/Futaba/T7PX-24G.User-Manual-P116-192/User-Guide-3526470-Page-58.png)
![Home screen Menu screen Model menu screen Data reset Reset execution Tap the [reset type]Reset type -Model data -User menu -Telemetry -All data175FunctionData Reset This function resets the contents of the currently called model memory.The reset method can be selected from among the 4 types described below. These resets do not initialize the adjuster function and system function.-Model dataInitializes only the function setting data. The direct menu function is not initialized.-User menuInitializes the user menu function. Other settings are not initialized.-Telemet r yTelemetry related setup data is initialized.-All data Initializes the direct selection function, receiver setting function and the setting data of each function.Data Reset 11 (Execution of reset)Select the type you want to reset and tap. A confirmation message will be displayed as "Are you sure?" If you want to execute, tap [No] to cancel with [Yes]. Reset is now complete.2 When finished, return to the Model menu screen by pressing the HOME button.Data Reset](https://usermanual.wiki/Futaba/T7PX-24G.User-Manual-P116-192/User-Guide-3526470-Page-59.png)
![Home screen Menu screen System menu screen Timer 176FunctionDisplayBacklight brightness, dimming time etc. setting and tap panel correction menu.There is also a tap panel sensitivity adjustment.Display1 (Backlight decrease brightness adjustment)Tap the value button of the [Backlight max, brightness] or [Backlight min, brightness]. Value input buttons appear on the screen and use the [+] and [-] buttons to adjust the backlight decrease brightness amount.2 (Backlight decrease time)You can set a time period to decrease the LCD backlight. This function counts the period that the touch panel has been not operated. This time can be set by one second steps. You can also turn off the backlight decrease if you like.Tap the value button of the [Backlight decrease time]. Value input buttons appear on the screen and use the [+] and [-] buttons to adjust the backlight decrease time amount.3 (Tap panel correction)Tap [Calibration]. It will be a black screen with a white + mark at the center of the screen. Tap on the intersection of that + mark in order, using 5 stylus pens etc of our company.To cancel, press the Home button to return to the display set-ting screen.Display setupAdjust button Adjust with the [+] and [-] but-tons.- Return to the initial value by tapping the [reset] buttons.Tap the + mark in 5 places in order.](https://usermanual.wiki/Futaba/T7PX-24G.User-Manual-P116-192/User-Guide-3526470-Page-60.png)
![177FunctionDisplay4 (Tap panel sensitivity adjustment)You can adjust the sensitivity of the tap panel.Tap the value button of the [Sensitivity]. Value input buttons appear on the screen and use the [+] and [-] buttons to ad-just the sensitivity of the touch panel.5 (Touch Panel Vibrate ON / OFF)The vibrate can be operated by the operation of the touch panel. Tap on the "Vibrator" (ON ) or (OFF) and select ON / OFF."OFF" :Function OFF"ON" :Function ON6 (Setting of start / end screen)Set whether or not to display the Futaba T7PX logo mark on startup and exit screens. If it is set to OFF, it disappears. Tap on the "Opening demo" (ON ) or ( OFF) and select ON / OFF."OFF" :Function OFF"ON" :Function ON7 When finished, return to the System menu screen by press-ing the HOME button.Adjust button Adjust with the [+] and [-] but-tons.- Return to the initial value by tapping the [reset] buttons.Sensitivity 10~100 Initial value : 30Setting- Tap (ON) / (OFF).Setting- Tap (ON) / (OFF).](https://usermanual.wiki/Futaba/T7PX-24G.User-Manual-P116-192/User-Guide-3526470-Page-61.png)
![Home screen Menu screen System menu screen InformationSelect / determine character Select a character, tap it to de-termine the characterName cursor movement Use the [ ] / [ ] tap to move the cursor. Also, when you de-cide a character, when the cur-sor position of the model name moves to the right, the cursor position of the model name moves to the right178FunctionInformationWith this system information, you can select user name setting, display language, use unit of telemetry information. Also displays the software version.Information1 (Moving the cursor to the character you want to change.)In the model name, tap [ ], [ ] to move the cursor and select the character of the model name you want to set or change. A vertical line cursor is displayed before the selected character.2 (Selection of characters to use)Select the character to use from the character list. When you decide the character to use, tap it. The character is deter-mined and the character string of the model name moves to the right. If you tap [BS], the left character of the vertical line cursor will be deleted. To redo, tap [Undo].3 When fi nished, return to the Model menu screen by press-ing the HOME button.amount.Setting the user nameMove cursor Deletion and cancellation of characters (Undo)Tap to select charactersSelection of alphabet / number / "kana"3 When fi nished, return to the System menu screen by pressing the HOME button.](https://usermanual.wiki/Futaba/T7PX-24G.User-Manual-P116-192/User-Guide-3526470-Page-62.png)
![Language select Tap to select from the list179FunctionMC Link (ESC Link)1 (Language select)Tap [Language], a list of languages will be displayed on the screen. If you tap the language you want to use from the list, the language display will be changed and you will be taken to the home screen.-The available languages will be added in the future.1 (Units system setting)Tap [Unit System] and set it to either the metric method or the yard / pound method.1 (Units system setting)Tap [Open source license], displays the manufacturer information and the license informa-tion of the font used in the system.Language settingUnits system settingDisplay of manufacturer information and open source license3 When finished, return to the System menu screen by pressing the HOME button.Setting- Tap Units system Meric system Yard-pound system](https://usermanual.wiki/Futaba/T7PX-24G.User-Manual-P116-192/User-Guide-3526470-Page-63.png)
![Home screen Menu screen System menu screen Sound180FunctionSoundThis function can set the volume of "Key Operation", "War ning" and "Telem r tor y speech info".-The volume of the click when edit key, jog, and trim are operated can be adjusted.-The volume of the audible alarm sound can be adjusted.-When the telemetry function is used, the volume of the voice that announces the tem-perature, speed, voltage, and other information at a ¿xed interval can be adjusted.Sound1 (Adjusting the key operetion volume)Tap the value button of the [Normal volume]. Value input but-tons appear on the screen and use the [+] and [-] buttons to adjust the volume.2 (Adjusting the warning volume)Tap the value button of the [Warning volume]. Value input buttons appear on the screen and use the [+] and [-] buttons to adjust the volume.3 (Adjusting the voice volume)Tap the value button of the [Voice volume]. Value input but-tons appear on the screen and use the [+] and [-] buttons to adjust the volume.Volume adjustment4 When finished, return to the System menu screen by pressing the HOME button.Adjust button Adjust with the [+] and [-] but-tons.- Return to the initial value by tapping the [reset] buttons.Normal volume 0~32 Initial value : 16Warning volume 1~32 Initial value : 16Voice volume 0~32 Initial value : 16](https://usermanual.wiki/Futaba/T7PX-24G.User-Manual-P116-192/User-Guide-3526470-Page-64.png)
![Home screen Menu screen System menu screen Battery181FunctionBatteryWith the T7PX, the low battery alarm setting is different, depending on the type of battery. Therefore, always set the battery type matched to the power supply to be used. When using a Futaba rechargeable type battery, always select "LiFe 2 cells" or "NiMH 5 cells". Incorrect setting will substantially shorten the time from low battery alarm to system stopping and is very dangerous.Exceptionally, when using a battery other than this, select "Other" and set the low bat-tery alarm voltage on your own responsibility. Futaba is not responsible for trouble caused by use of an unspeci¿ed battery.Battery1 (Select battery type)Tap [Battery type], a list of battery type will be displayed on the screen. tap the battery type you want to use from the list.-When set to [Other], please set the alarm voltage by yourself.2 (Select vibrator type)Tap the [Vibrator] type and select [Inhibit], [Type 1], [Type 2], or [Type 3].3 (Auto power off setting )Tap on the "Auto power off" (ON ) or ( OFF) and select ON / OFF.“OFF” :Function OFF“ON” :Function ON4 When finished, return to the System menu screen by press-ing the HOME button.Battery settingSetting- Tap list LiFe 2 sell NiMH 5 cell OtherSetting- Tap Vibrator type. TInhibit/ Type 1/ Type 2/ Type 3 Setting- Tap (ON) / (OFF).](https://usermanual.wiki/Futaba/T7PX-24G.User-Manual-P116-192/User-Guide-3526470-Page-65.png)
![Home screen Menu screen System menu screen Data And Time182FunctionData And TimeThis function adjusts the system clock of the T7PX transmitter. Perform this setting when you purchase the set and when adjustment is necessary.Whether the time or the total timer (accumulation timer) is displayed on the initial screen can be set. The total timer can be reset at this menu.Data And Time1 (Date and time setting)Tap the value button of the [Year], [Month], [Day], [Hour], [Minute] or [Second]. Value input buttons appear on the screen. use the [+] and [-] but-tons to set the date and time amount. When the setting is changed, the [Time adjust] button will be displayed, so tap this to update the system clock.- The date and time will be reset after a long pe-riod of time with the battery removed from the transmitter.2 (Total tome reset)Tap the [Reset]. The total time is reset. 3 (Select home screen display mode)Tap on the "Display mode" [Clock] or [Total timer] and select Clock / Total timer.Date and time setting4 When finished, return to the System menu screen by pressing the HOME button.Adjust button Adjust with the [+] and [-] but-tons.- Return to the initial value by tapping the [reset] buttons.Timer reset tap the [reset] Setting- Tap display mode. Clock Total time](https://usermanual.wiki/Futaba/T7PX-24G.User-Manual-P116-192/User-Guide-3526470-Page-66.png)
![Home screen Menu screen System menu screen LED Setting183FunctionLED SettingYou can adjust the brightness and lighting method of the pilot LED light.The pilot LED lighting method can be selected from "always on", "off " or "interlock with backlight".LED Setting1 (Setting pilot LED)Tap the [Pilot LED], a list of lighting mode will be displayed on the screen. tap the lighting mode you want to use from the list.LED setting2 (Setting Pilot LED brightness)Tap the value button of the [Brightness]. Value input buttons appear on the screen and use the [+] and [-] buttons to ad-just the pilot LED brightness amount.3 When finished, return to the System menu screen by pressing the HOME button.Pilot LED modeBacklight, Always On, OFFAdjust button Adjust with the [+] and [-] but-tons.- Return to the initial value by tapping the [reset] buttons.Brightness 0~20 Initial value : 20](https://usermanual.wiki/Futaba/T7PX-24G.User-Manual-P116-192/User-Guide-3526470-Page-67.png)
![Home screen Menu screen System menu screen Calibration184FunctionCalibrationSteering and throttle correction can be applied. Use this function when a mechanical offset has occurred for some reason.CalibrationHowever, if correction was applied, it may be necessary to recheck the set values of all the setup functions.(Preparation) Tap the [Wheel]. The neutral correction screen appears.1(Steering neutral adjustment) After the wheel lightly to the left or right, tap the [Neutral] in the state in which the wheel is not touched. If neutral correc-tion is OK, the end point correction screen appears. If not within the correction range, the end point correction screen will not appear.2(Steering wheel travel adjustment) In the end point correction screen (figure at the right) state, lightly turn the wheel fully to the left and right and tap the [End point]. If end point correction is OK, the display returns to the adjuster screen. If the end point is not within the correction range, the display does not return to the adjuster screen. In this case, return to the system menu screen by pressing the HOME button. If operation cannot be ended normally even when correction is repeated, please contact the Futaba Ser-vice Center.Steering adjustment3 When finished, return to the System menu screen by pressing the HOME button.](https://usermanual.wiki/Futaba/T7PX-24G.User-Manual-P116-192/User-Guide-3526470-Page-68.png)
![185FunctionCalibration(Preparation) Tap the [Trigger]. The neutral correction screen appears.1(Throttle neutral adjustment) After lightly pulling the throttle trigger to the forward and brake, tap the [Neutral] in the state in which the trigger is not touched. If neutral correction is OK, the end point correction screen appears. If not within the correction range, the end point correction screen will not appear.2(Throttle trigger travel adjustment) In the end point correction screen (figure at the right) state, lightly operate the trigger to the full forward and full brake side and tap the [End point]. If end point correction is OK, the dis-play returns to the adjuster screen. If not within the correction range, the display will not return to the adjuster screen. In this case, return to the system menu by pressing the HOME but-ton. When operation cannot be ended normally even when correction is repeated, and cannot be ended normally, contact the Futaba Service Center.Throttle adjustment3 When finished, return to the System menu screen by pressing the HOME button.](https://usermanual.wiki/Futaba/T7PX-24G.User-Manual-P116-192/User-Guide-3526470-Page-69.png)
![189Reference- If the alarm is not reset, the auto power off function will auto-matically turn off the power after 5 minutes. - The alarm stops even if the [OK] is tapped. However, check the function switch. Audible alarm: Continuous tone. Warning DisplaysLow Battery AlarmPower off forgotten alarmIf the transmitter battery voltage drops below the usable range, an audible alarm will sound and "Low battery" will be displayed. Since the usable range of LiFe and NiMH batteries and LiFe batteries is different, the power supply used must be set by system setting.(page 181)At T7PX initialization, if steering wheel, throttle trigger, push switch, HOME button, or other operation is not performed within 10 minutes, an audible alarm will sound and the message "Warning: Auto power off" will appear. If steering wheel, throttle trigger, push switch, HOME button or other operation is performed, the alarm is reset. Also turn off the power when the transmitter is not in use. If you do not want to use this alarm and the auto power off function, they can be disabled by system setting. (page 181)Audible alarm: Continuous tone. The vibrator: Active (initial setting) page 181Warning When a low battery alarm is generated, cease operation immediately and retrieve the model. If the battery goes dead while in operation, you will lose control. MIX WarningWhen the power switch is turned on while the idle-up, engine cut or neutral brake function switch is on, an audible alarm will sound and "Warning" will be displayed on the LCD. When that function switch is turned off, the alarm will stop.Audible alarm: Continuous tone. RF Error When the RF module does not operate, "RF Error" is displayed on the LCD and an audible alarm will sound. Immediately turn off the power.Audible alarm: Continuous tone. - To stop the alarm, turn off the power. - Turn the power back on. If the alarm is generated again, request repair from the Futaba Service Center.](https://usermanual.wiki/Futaba/T7PX-24G.User-Manual-P116-192/User-Guide-3526470-Page-73.png)
