Futaba T18MZ-24G Radio Control User Manual

Futaba Corporation Radio Control

$31<Before Use>S.BUS Wiring exampleBatteryBatteryGY520ExtensioncordSwitchTerminal boxHUBHUB HUBHUB HUBHUBHUBق$QRWKHUSRZHUVXSSO\كHUBق$QRWKHUSRZHUVXSSO\كS.BUS ServoS.BUS Servo,WRSHUDWHVLQDQRWKHUSRZHUVXSSO\IRUWKHUHFHLYHUReceiver䃂S.BUS Servo Since the channel number is memorized at the S.BUS itself beforehand, any connector can be used. When the SBD-1 sold separately is used, ordinary servos can be used with the S.BUS system.䃂When separate power supply used When many more servos are used and when large current servos are used the servos are driven by a separate power supply by using a separate power supply 3-way hub.䃂Terminal boxFour connectors can be inserted Three connectors can be inserted. Used when using a separate power supply battery.S.BUSPort(8/SB)OrangeGreenWarningPower supply3OHDVHXVHDEDWWHU\ZLWKFDSDFLW\RIenough to the number and kind of servo.A dry battery cannot be used.$

$32 <Before Use>S.BUS2 System S. BUS2, extend the conventional S.BUS system and support bidirectional communication systems, such as a telemetry sensor.Receiver connector S.BUS ServoS.BUS Gyro telemetry sensorS.BUS 䂾㬍S.BUS2 㬍䇭䋨㶎䋩䂾S.BUS device setting S.BUS servos or a telemetry sensor can be connected to the T18MZ and channel setting (slot setting) and other settings can be memorized at the S.BUS device.S.BUS2 TABLE䋨㶎䋩'RQWFRQQHFW6%866HUYRS.BUS Gyro to BUS2 connector. HUB or Y-adaptor(S.BUS Servo)S.BUS device(telemetry sensor)ReceiversBatteryT18MZ&RQQHFWWKH6%86GHYLFHDQGEDWWHU\\RXZDQWWRVHWZLWKDZD\KXERUZD\FRUGDVVKRZQLQWKHÀJXUH7XUQRQWKHWUDQVPLWWHUSRZHU&DOOWKHVHWXSVFUHHQ䇭6HUYR6\VWHP0HQX→6%866HUYR䇭6HQVRU/LQNDJH0HQX→6HQVRU3HUIRUPVHWWLQJLQDFFRUGDQFHZLWKHDFKVFUHHQ7KLVPHPRUL]HVWKHFKDQQHOVORW1RDWHDFK6%86GHYLFHVRLWFDQEHXVHGE\FRQQHFWLQJLWWRWKH6%86FRQQHFWRURIWKHUHFHLYHU$

33<Before Use>Telemetry SystemThis set is compatible with a telemetry system. Flight status can be displayed at the transmitter by mounting various sensor units to the fuselage.*The telemetry function is applicable only in the FASSTest 18CH mode. (12CH mode serves as a displa y o f only Receiver battety voltage and Extra battety voltage.)*The telemetry function requires the corresponding receiver (R7008SB).S.BUS2ConnectorTemperatureSensor Slot1Slot2Slot3Slot4Slot5Slot6Slot7ReceiverBattery voltage is displayed at the transmitter.Drive battery voltage is displayed at the transmitter.SwitchT18MZGY520ExtensioncordTerminal boxHUBHUBHUBInfoInfoInfoInfoInfo InfovoltageSignalRPMSensorAltitudeSensorAltitudeSensorAltitudeSensorSensorSlot8S.BUS2 ToolSensor䃂Telemetry sensor (sold separately)Fuselage data can be checked at the transmitter by connecting various telemetry sensors to the S.BUS2connector of the receiver.䃂Slot No.Servos are classified by channel, but sensors are classified by “slot” . Since the initial slot No. of the T18MZ is preset at each sensor, the sensors can be used as is by connecting them. There are 131 slots.

34 <Basic Operation>BASIC OPERATIONBattery ChargingBefore charging batteries, read the "Cautions for handling battery and battery charger" in the section "For your safety".Charging the transmitter LT2F3500XH lithium-polymer batteryDangerThe LT2F3500XH lithium-polymer battery is for the T18Mz transmitter only. Do not use it with other devices.Always use the accessory AC adapter to charge the battery.The charging circuit is built into the T18MZ.[Method of charging battery]T18MZAC100V Charge lamp1. Turn off the transmitter power.2. Connect the power plug of the AC adapter to an AC100V outlet.*Don't connect AC plug to T18MZ without connecting with AC100V.3. Open the back lid of the transmitter and insert the plug of the AC adapter into the CHG port.4. The charging monitor of the transmitter lights red.*The LCD screen will come on for several seconds and then go off. It may take several tens of seconds for charging to start after the AC adapter is connected.5. When the battery is fully charged the transmitter monitor will light green. A charge plug is pulled out and an AC adaptor is removed.*After using the AC adapter always disconnect the power cord from the AC outlet.*The charging time when charging a completely discharged battery pack is approximately 2 hours 30 seconds. However, the actual charging time may be different from the above depending on the ambient temperature and state of the battery pack.*If the battery is improperly installed or is faulty, the transmitter monitor will not light and the battery will not be charged.How to charge the Li-Fe battery FR2F1800(Option) for the receiverUse the battery charger that is included in the set.[Method of charging battery]AC100V3S2SMODEL :LBC-4E5Intelligent LiFePO4 for 2S/3S CellsBalance CHARGERRed on, green off : ChargingRed flash : Output short-circuit or wrong polarityGreen on, red off : Charging Full䃂The connector of the battery isconnected with "2S" side ofthe charger.䋨2S sids䋩Charger LBC-4E51. Connect the power cable of the charger to the wall socket (AC outlet).2. Connect the connector to the Li-Fe battery.&RQ¿UPWKDWWKHFKDUJLQJLQGLFDWRU/('ODPS5HGOLJKWV3. Remove the battery after LED lamp Green lighting .*After completing the charge remove the battery from the charger and remove the charger from the wall socket.WarningThe transmitter battery cannot be charged with the receiver charger. Conversely the receiver battery cannot be charged with the transmitter charger.

$35<Basic Operation>How to turn ON/OFF the power of the transmitterWindows®&(LVLQVWDOOHGDVDEXLOWLQRSHUDWLQJsystem in the T18MZ transmitter. Compared to the conventional system, the T18MZ takes extra time for internal processing when it is turned on/off.When turning on the power of the transmitter1. Make a throttle stick slow.2. Turn on the power switch of the transmitter.$IWHULQLWLDOL]DWLRQRIWKHWUDQVPLWWHULVRYHU/('PRQLWRUturns on Purple.*If a throttle stick turns on by the high speed side (1/3 or more), warning will become. If it returns slowly, warning will stop and will become a "Transmit ?" screen.*If you push the button "NO", then the transmitter will not emit radio waves.*If you push the button "Yes", then the transmitter will emit radio waves.Start-up time; The time required for initializing the internal circuit of the transmitter varies between the previous time you turned off the transmitter and the time you will turned on the power. There are two “start up” modes for your transmitter, see below:Cold start;If you turn on the transmitter more than four hours after you last turned it off, the mode is “Cold start”. “Cold start” is normal for the first initial power up of the day. It will take about 30 seconds to be ready for use, as it takes time to initialize the internal circuit of the transmitter. Hot start;If you turn on the transmitter less than four hours after you last turned it off, the mode is “Hot start”. Since initialization has been partly completed, the transmitter will be ready to use in several seconds. ³+RWVWDUW´WDNHVSODFHXVXDOO\DWDVHFRQGÀLJKWRUODWHUÀLJKWLQWKHGD\WarningOnce you turn on the power, never shut off the power switch until the power becomes stable (or XQWLOWKH¿UVWVFUHHQVKRZVXS,I\RXWXUQRIIthe power switch while the transmitter is going through the initialization process, the data could be damaged. Note: The start-up time may be a little bit slower when the SD card is installed compared to when the card is not.How to stop the transmitterTurn off the power switch of the transmitter. The internal circuit of the transmitter starts the shut down process including saving the set-up data. The /('ZLOOEOLQN\HOORZZKLOHWKHWUDQVPLWWHULVLQthe shutdown process. Once you turn off the power, never operate the power switch until the power shutdown process is fully completed. If you turn on the power switch again while the transmitter is still in the process of power shutdown, the data could be damaged.The right switch is pushed.It turns it off by pushing 2 pieces simultaneously.It turns it off by pushing 1 pieces pushes for a long time.or$

$36 <Basic Operation>Registration of the user's nameT18MZ transmitter can register user's name. How to register user's name1. Turn on the power of the transmitter.2. Push the area of the user's name shown on the home screen or the "user's name" in the linkage menu. Then the User's Name Set screen will pop up.85%User Name Model1User Name User ID Secure Mode Futaba Corporation0000System3. Push the user's name. Then the keyboard will pop up. You can use up to 32 characters as a user's name. Use the keyboard on the screen to enter user's name.space keyEnter and Exit : [Return] Key, Cancel and Exit : [ESC] Key3LHDVHLQSXWXVHUQDPH۹&KDUDFWHUVFutaba Corporation4. Push "Return" key to return to the previous screen after entering the user's name.(If you want to protect the user's name)If you don't want anybody else to change your user's name, set your ID in the following way.*Please be aware that you will not able to change user's name if you forget your password. 1. Make sure that the security mode is "User's name", and then push the User ID button.2. Enter your password, using keyboard on the screen.You will need to enter your password for changing the user's name from the next time you turn on the power of the transmitter.(YHQLI\RXHQWHUWKHVDPHFKDUDFWHU\RXUSDVVZRUGZLOOEHidentified differently depending on whether you are using "Transform" mode or "Direct" mode for inputting.As the internal circuit of the transmitter stays on the standby mode for 4 hours after turning off the power, some part of the circuit is consuming current. When you turn on the power during this period, the power starts in “Hot mode”. But if more than four hours pass after shutting down the power, the power supply will completely shut down the internal circuit. When you turn on the power after this point, the power starts in “Cold start mode”. How to reset softwareIf the screen freezes for some reason and you cannot edit, the transmitter power supply is not shut off even if you turn OFF the power switch. You will need to use the remove the battery and reinsert it again. In this case, the power restarts in “Cold PRGH´(YHQWKRXJKWKHVFUHHQIUHH]HVDOOWKHother functions for radio control operation remain operative.$

$37<Basic Operation>TimerIf one of two timer displays ispushed, it can move to thetimer screen of a Linkagemenu.WarningBe sure to confirm the model name before flyingyour aircraft.Check the remaining battery as often as possible and try to charge the battery earlier. If the battery alarm makes a sound and its warning symbol is displayed, land your aircraft immediately.Ɣ$OWKRXJK\RXPD\QRWLFHWKHIOLFNHULQJRIWKHQXPEHUVRQWKHLCD screen, this is not an abnormal, because the LCD screen is frequently refreshing those even if those numbers are unchanged.Ɣ<RXFDQDGMXVWWKH/&'FRQWUDVWDQGWKHEDFNOLJKWEULJKWQHVVand can change the duration time to turn off the backlight and color of the background by the screen setting in the system menu.Home screenConditionThe condition name that is currently used is displayed here. 3XVKWKLVDUHDWRcall the ConditionSelect screen.ClockThis shows the today's date and the current time. 3XVKWKLVDUHDIRUWKHDate & Time Settingscreen.User's namePush this area to call the User's Name Setting screen.System Selection)$667HVW&+)$667HVW&+)$66708/7)$667&+6)+66&+System timer/Reset7KLVVKRZVWKHDFFXPXODWHGtime up to now since the latestreset.(Hour):(Minute):(Second)Push this area to reset the timer.Direct buttonsSelect and push one of the direct buttons to call its setting screen.+HUHLVWKHKRPHVFUHHQDQGLWVGHVFULSWLRQV8VH\RXU¿QJHURULQFOXGHGVW\OXVSHQWRRSHUDWHWKHWRXFKscreen.(Menu Button)ŏ0RGHO(Menu Button)ŏ6\VWHPŏ/LQNDJHBattery Indicator:KHQWKHUHPDLQLQJbattery reaches 30%, the alarm will beep. Land your aircraft immediately.RF Indicator21$,5 or5)2))Digital trim (T1 to T6, CD)Push this area to call theDial Monitor screen.Model NameThe model name that is currently used is displayed here.3XVKWKLVDUHDWRFDOOWKHModel Select screen.voltage of Rx battery Information from the receiver is displayed with an bidirectional system.$

$38 <Basic Operation>22:15:10User MenuT18MZ has each menu of a System / Linkage / Model. User Menu can be created the item often used by itself for others can be chosen. Its own favorite original menu can be GLVSOD\HGLI5RWDU\.H\LVSXVKHGHow to make a User Menu1. From a home screen, a Rotary key ispressed long time.2. The place to register is pushed.3. Since all the items are displayed on all the4 pages, an item to display is chosen.4. The User Menu of all the 32 items can becreated. From a home screen, a key ispressed for a long time, is called, and isused.ŏ5HWXUQWRKRPHVFUHHQŏ5HWXUQWRKRPHVFUHHQŏ5HWXUQWR8VHU0HQXŏ,WGHOHWHVIURPDXVHUPHQX It is not deleted from the menu of a basis.*The item called from the user menu and the item called IURPWKHXVXDOPHQXDUHWKHVDPH&KDQJHLVUHÀHFWHGeven if called from which.$

$39<System Menu>SYSTEM MENUSystem Menu functions table[Trainer]: Starts and sets the trainer system.[Display]: Display adjustment and auto power off setting.[Date & Time]: Sets the date and time (system clock setting) and resets the timer.[User Name]: User name registration and ID Pin number.[Switch]: Toggle switch type setting (Set when the switch is replaced.)[H/W Setting]: Hardware reverse / Stick setting / Calibration.[Sund Volume]: This volume is adjusted. Key Operation/Error Warning/Trim&Center Click/Timer Event.>3OD\HU@5HSURGXFWLRQRIPXVLF¿OH[Camera]: Function that takes pictures with a camera.[S.BUS Servo]: S.BUS servo setting.[Information]: Displays the program version, SD card information, and product ID.[Range Check]:The output of the transmitter is lowered, and the Range checked.The System Menu sets up functions of the transmitter, this does not set up any model data.ŏ:KHQWKH6\VWHP0HQXEXWWRQLVWRXFKHGWKHPHQXVKRZQEHORZLVFDOOHG&DOOWKHVHWXSVFUHHQE\SUHVVLQJWKHIXQFWLRQ\RXZDQWWRVHWXSŏ5HWXUQWR+RPHVFUHHQ$

$40 <System Menu>Trainer Trainer system starting and settingT18MZ trainer system makes it possible for theinstruction to chose which channels and operation modes are to be used at the instructor's transmitter. Because the switch and rate of each channel can be set, the training method can also be matched to the student's skill level. Two transmitters must be connected by an optional Trainer Cord, and the Instructors’ transmitter should be programmed for trainer operation, as described below.When the Instructor activates the trainer switch, the student has control of the aircraft (if MIX/ FUNC/NORM mode is turned on, the Instructor can make corrections while the student has control). When the switch is released the Instructor regainscontrol. This is very useful if the student gets the aircraft into an undesirable situation.ŏ6HWWLQJGDWDDUHVWRUHGWRPRGHOGDWDŏ6WXGHQWUDWHFDQEHDGMXVWHGDW0,;)81&1250PRGHŏ$FWLYDWHGVWXGHQWFKDQQHOVFDQEHVHOHFWHGE\VZLWFKHVNOTE: This trainer system can be used in the following manner;1. In the T18MZ (including FX-40, T12Z and T12FG) transmitter and a conventional transmitter, if the channel order is different. It is necessary to match the channel order in the Linkage Menu when connecting it with other than a T18MZ.2. Be sure that all channels work correctly in ERWKWUDQVPLWWHUVEHIRUHÁ\LQJCorresponding types of transmitters and trainer mode settings:7\SHVRIWUDQVPLWWHUV,QVWUXFWRUVWUDQVPLWWHUVHWWLQJV6WXGHQWVWUDQVPLWWHUVHWWLQJV)UHTVHWWLQJ7UDLQHUVHWWLQJ)UHTVHWWLQJ7UDLQHUVHWWLQJ7UDLQHU&RUGV,QVWUXFWRU6WXGHQW0RGPRGH&+PRGH0RGPRGH&+PRGH0RGPRGH70= 70= $UELWUDU\&+ $UELWUDU\&+-)*&7UDLQHU&RUGV70=70=);7=7)*);$UELWUDU\&+3&0**&+33070=7)*);$UELWUDU\&+)$6670/7--&+)$66708/770=7&7&7&7(;7(;$UELWUDU\&+330--)*7UDLQHU&RUGV70=7&*7&*$UELWUDU\&+ $UELWUDU\--)*7UDLQHU&RUGV70= 7-7-$UELWUDU\&+ $UELWUDU\--)*& 7UDLQHU&RUGV70=);7=7)*);70=$UELWUDU\&+$UELWUDU\&+-7)*);70=$UELWUDU\&+$UELWUDU\&+-7&7&*7&7&7&*7-70= $UELWUDU\-$UELWUDU\&+-*It cannot be used by the set of those other than a diagram.(As of November, 2011 )ŏ7RXFKWKH>7UDLQHU@EXWWRQDWWKH6\VWHP0HQXWRFDOOWKHVHWXSVFUHHQ7KHVHWXSVFUHHQIRUWKHVWXGHQWPRGHLVVKRZQEHORZ85%TrainerStudentINHACT/INH8CHChannelTeacher/StudentModel 1Student mode6HW7HDFKHU6WXGHQWEXWWRQWR6WXGHQW&KDQJH$&7,1+EXWWRQIURP,1+WR2))RU216HWWKH&+PRGHWR&+&+RU&+VHHWKHDERYHFKDUWIRUWKHWUDLQHUPRGHŏ5HWXUQWR6\VWHP0HQXVHWWLQJV1RWH,QVWXGHQWPRGHRQO\WKHWHDFKHUVLGHFDQWXUQRQDQGRIIWKHSRZHURIWKHVWXGHQWVWUDQVPLWWHU.HHSWKHSRZHUVZLWFKDOZD\VDWRIISRVLWLRQ$

$41<System Menu>Teacher mode6HW7HDFKHU6WXGHQWEXWWRQWR7HDFKHU&KDQJH$&7,1+EXWWRQIURP,1+WR2))RU216HWWKH&+PRGHWR&+&+RU&+VHHWKHDERYHPHQWLRQHGFKDUWIRUWKHWUDLQHUPRGHVHWWLQJV&DOOXSWKH6ZLWFK6HWWLQJVFUHHQE\WRXFKLQJ6ZLWFK7KHQVHWWKHGHVLUHGVZLWFKDQGRQRIIGLUHFWLRQ6HOHFWWKHVZLWFKPRGH,I\RXVHOHFW1250WKHWUDLQHUIXQFWLRQZLOOEHWXUQHGRQRURIIE\DVZLWFKSRVLWLRQ,I\RXVHOHFW$/721DQG2))RIWKHWUDLQHUIXQFWLRQVZLWFKHVDOWHUQDWLYHO\HYHU\WLPHWKHVZLWFKLVWXUQHGRQ7KLVPHDQVWKHVWXGHQWVLGHFDQEHRSHUDWHGZLWKRXWKROGLQJWKHVZLWFKOHYHU7KH,QVWUXFWRUVLGHVHOHFWVWKHFKDQQHOIRUFRQWURO7KUHHRSHUDWLQJPRGHVDUHDYDLODEOH"NORM" mode (Normal mode);6WXGHQWVLGHKDVQRFRQWURORIPL[HVDQGVHWWLQJVLQ7HDFKHUVUDGLR"MIX" mode;6WXGHQWKDVIXOODGYDQWDJHRIDOOVHWWLQJLQ7HDFKHUVUDGLRSOXV7HDFKHUKDVWKHRSWLRQWRFKDQJHDQ\VHWWLQJZKLOH6WXGHQWKDVFRQWURO"FUNC" mode (Function mode);6WXGHQWKDVFRQWURORIPL[HVDQGUDWHVHWWLQJVRI7HDFKHUVUDGLR6HWWKHVZLWFKHVDQGUDWHVRIHDFKFKDQQHO6ZLWFKWRWKHGHWDLOVVHWXSVFUHHQE\WRXFKLQJWKHSDJHVZLWFKLQJEXWWRQ>@DWWKHWRSULJKWKDQGFRUQHURIWKHVFUHHQ6WXGHQWRSHUDWLRQIRUHDFKFKDQQHOFDQEHVHWKHUH>6ZLWFK@7KHVZLWFKHVWKDWFDQEHRSHUDWHGE\WKHVWXGHQWFDQEHVHW6:$a6:+66DQG66FDQEHVHOHFWHG>5DWH@6HUYRWUDYHOYHUVXVVWXGHQWRSHUDWLRQFDQEHVHW7KLVFDQRQO\EHXVHGLQWKH)81&/0,;1250PRGHV1RWH,QWHDFKHUPRGHWKHWUDLQHUIXQFWLRQZRQ·WEHWXUQHGRQXQOHVVWKH,QVWUXFWRUVWUDQVPLWWHUUHFHLYHVVLJQDOVIURPWKHVWXGHQWVWUDQVPLWWHU%HVXUHWRFRQILUPWKLVDIWHUFRQQHFWLQJ\RXUWUDLQHUFDEOH85%Trainer 1/3TeacherINHACT/INH CH Function Mode Switch Rate Stu.CH1 ELE2 ELE23 RUD4 AIL5 AIL26 THR8CHChannelOFFOFFOFFOFFOFFOFFOFFOFFOFFMaster SWTeacher/StudentModel 1ŏ5HWXUQWR6\VWHP0HQX85%Trainer 1/3TeacherINHACT/INH CH Function Mode Switch Rate Stu.CH1 ELE2 ELE23 RUD4 AIL5 AIL26 THR8CHChannelOFFFUNCMIXOFFOFFNORMOFFOFFOFFMaster SWTeacher/StudentModel 1NULLNULLNULL+100+100+100CH 2NULLCH 4ŏ6WXGHQWUDWHŏ7KHVHWXSVFUHHQIRUWKHLQVWUXFWRUPRGHLVVKRZQEHORZ$

$42 <System Menu>Student channel setting2SHQWKH6\VWHP0HQXWUDLQHUVFUHHQ6HOHFW>7HDFKHU@:KHQ>)81&@>0,;@>1250@LVVHOHFWHGDVWKHPRGHRIWKHFKDQQHOWREHVHWWKH>6WXGHQW&+@VHWWLQJEXWWRQLVGLVSOD\HG:KHQ>2))@>6WXGHQW&+@VHWWLQJLVQRWSHUIRUPHG:KHQWKH>6WXGHQW&+@EXWWRQLVSUHVVHGWKH&KDQQHO6HOHFWVFUHHQLVGLVSOD\HG6HOHFWWKHFKDQQHOTrainer student channel setting functionWhich channel of the signal from the student transmitter is fetched as the student function input signal when "FUNC""MIX""NORM" is set as the trainer function student's transmitter mode can be set. This makes trainer connection easy even when the instruction side and student side channel assignment is different.85%Trainer 1/3TeacherINHACT/INH CH Function Mode Switch Rate Stu.CH1 ELE2 ELE23 RUD4 AIL5 AIL26 THR8CHChannelOFFFUNCMIXOFFOFFNORMOFFOFFOFFMaster SWTeacher/StudentModel 1NULLNULLNULL+100+100+100CH 2NULLCH 4Student side Student CHCH1 AileronCH2 ElevatorCH3 ThrottleCH4 RudderCH5 GearCH6 FlapCH7 Aileron2CH8 Aux5CH9 Aux4CH10 Aux3CH11 Aux2CH12 Aux1Instructor sideCH2Elevator CH4Rudder CH3Throttle CH1Aileron --Aileron2 CH6Flap CH5Gear CH8Aux5 CH9Aux4 CH10Aux3 CH11Aux2 CH12Aux1([DPSOHRIVWXGHQW&+VHWWLQJ!$

$43<System Menu>Model 185%Display-+-+30Min.1Min.$XWR3RZHURíWLPHBacklight decreaseBack color Touch screen%DFNOLJKWGHFUHDVHWLPHBacklightTEXT TEXT TEXT TEXT TEXT Cal.Auto power off time setting$GMXVWWKHDXWRSRZHURIIWLPHZLWKWKHOHIWDQGULJKWVLGHEXWWRQV*When the time the transmitter is inactive exceeds the set time, the power is turned off automatically. This time can be set up to 1 hour in 10 minutes increments. The auto power off function can also be deactivated.*An audible alarm is sounded and an alarm screen is displayed from 3 minutes before auto power off and the time remaining until auto power off is displayed. When a stick or switch is operated while the alarm screen is being displayed, the alarm is cleared and the display is returned to the home screen.Backlighting brightness adjustment$GMXVWWKHEDFNOLJKWLQJEULJKWQHVVZLWKWKHOHIWDQGULJKWVLGHEXWWRQV*When the right side button is touched, the backlightingbecomes brighter. When the left side button is touched, the backlighting becomes darker.Backlight decrease brightness adjustment$GMXVWWKHEDFNOLJKWGHFUHDVHEULJKWQHVVZLWKWKHOHIWDQGULJKWVLGHEXWWRQV*When the right side button is touched, the backlightingbecomes brighter. When the left side button is touched, the backlighting becomes darker.*It cannot be made brighter than Backlighting brightness adjustment.Backlight decrease time<RXFDQVHWDWLPHSHULRGWRGHFUHDVHWKH/&'EDFNOLJKW7KLVIXQFWLRQFRXQWVWKHSHULRGDisplay/&'VFUHHQDGMXVWPHQWDQGDXWRSRZHURIIVHWWLQJThe following LCD screen adjustments and auto power off setting are possible:ŏ$XWRSRZHURIIWLPHVHWWLQJŏ%DFNOLJKWLQJEULJKWQHVVDGMXVWPHQWŏ%DFNJURXQGFRORUFKDQJHŏ7RXFKSDQHOVFUHHQSRVLWLRQFRUUHFWLRQŏ7RXFKWKH>'LVSOD\@EXWWRQLQWKH6\VWHP0HQXWRFDOOWKHVHWXSVFUHHQVKRZQEHORZŏ5HWXUQWR6\VWHP0HQXWKDWWKHWRXFKSDQHOKDVEHHQQRWRSHUDWHG7KLVWLPHFDQEHVHWE\WHQVHFRQGVWHSV<RXFDQDOVRWXUQRIIWKHEDFNOLJKWGHFUHDVHµLI\RXOLNH*The backlight consumes a large amount of power. We recommend you to turn off the backlight by setting the backlight power-off time to about one minute.*Since the backlighting power consumption is extremely high, we recommend that the backlighting off time be made short.Background color7RXFKWKHEXWWRQRIWKHFRORU\RXZDQWWRFKDQJH7KHUHDUH¿YHEDFNJURXQGFRORUVTouch screen calibration7KLVIXQFWLRQDGMXVWVWKHORFDWLRQRIWRXFKSDQHO7RXFK&DOLEUDWLRQEXWWRQDQGWKHQSUHVV<HVWKHFDOLEUDWLRQVFUHHQZLOOSRSXS7RXFKWKHFHQWHURIWKHFURVVKDLUFXUVRURQWKHVFUHHQZLWKWKHVW\OXVSHQ$VVRRQDVWKHV\VWHPUHFRJQL]HVWKHSRVLWLRQWKHFXUVRUZLOOPRYHRQWRWKHQH[WSRVLWLRQ5HSHDWWKLVSURFHGXUHDVORQJDVWKHFXUVRUPRYHVWRQH[WSRVLWLRQ<RXZLOOGRWKLVILYHWLPHV&DOLEUDWLRQZLOOEHFDUULHGRXWEDVHGRQWKHILYHSRVLWLRQV'LVDSSHDUDQFHRIWKHFURVVKDLUFXUVRUPHDQVWKHFDOLEUDWLRQKDVEHHQFRPSOHWHG7RXFKDQ\SRLQWRQWKHVFUHHQWRUHWXUQWRWKHSUHYLRXVVFUHHQ*In ordinary operation, this calibration is not necessary. If you notice the touch panel is not functioning correctly after long use, we recommend you to carry out this calibration.$

$44 <System Menu>Model 1 85%Date and TimeSystem TimerDate2011 8 17August 2011SMTWTFS31 123456456789107891011 12 1318 19 2014 15 1624 25 26 2721 22 2331 12 328 29 3017Time16Total 00:17:4835 52Date setting7RXFKWKH<HDU0RQWKRU'D\EXWWRQDQGVHWWKHGDWHE\WRXFKLQJWKH>@RU>@EXWWRQ*The date can also be set by pressing the date on the calendar shown at the left.Time setting7RXFKWKH+RXURU0LQXWHEXWWRQDQGVHWWKHWLPHE\WRXFKLQJWKH>@RU>@EXWWRQ:KHQWKH6HFRQGEXWWRQLVWRXFKHGWKHWLPHULVVHWWRVHFRQGVIntegrating timer reset7KHLQWHJUDWLQJWLPHUVKRZVWKHWRWDOWLPHWKDWKDVHODSVHGVLQFHWKHODVWUHVHWWLQJ:KHQWKH>6\VWHP7LPHU@EXWWRQLVWRXFKHGWKHWLPHULVUHVHWDate and Time'DWHDQGWLPHVHWWLQJV\VWHPFORFNVHWWLQJDQGLQWHJUDWLQJWLPHUUHVHWWLQJThis function adjusts the system clock of the T18MZ transmitter. Perform this setting when you purchase the set and when adjustment is necessary.ŏ7RXFKWKH>'DWHDQG7LPH@EXWWRQLQWKH6\VWHP0HQXWRFDOOWKHVHWXSVFUHHQVKRZQEHORZThe integrating timer can also be reset.*The integrating timer is displayed on the Home screen.ŏ5HWXUQWR6\VWHP0HQX$

$45<System Menu>85%User Name Model1User Name User ID Secure Mode Futaba Corporation0000SystemUser Name 8VHUQDPHUHJLVWUDWLRQDQG3,1VHWWLQJThis function registers the T18MZ user name.A PIN can also be set to protect the set data or user name.ŏ7RXFKWKH>8VHU1DPH@EXWWRQDWWKH6\VWHP0HQXWRFDOOWKHVHWXSVFUHHQVKRZQEHORZ*Set the PIN carefully. When a system PIN is set, if youforget the PIN, none of the settings can be changed. In this case, the system must be reset by the Futaba Service Center. ŏ5HWXUQWR6\VWHP0HQXUser name registration:KHQWKH8VHU1DPHER[LVWRXFKHGDNH\ERDUGDSSHDUVRQWKHVFUHHQ(QWHUWKHXVHUQDPHIURPWKLVNH\ERDUG*A user name of up to 32 characters can be entered. *The set user name is displayed on the Home screen.(For a detailed description of the input method, see [User Name Registration/Character Input Method] in the BasicOperation section.)User name or set data protection7RXFKWKH6HFXULW\0RGHEXWWRQDQGVHOHFWWKHPRGH7KHPRGHLVVZLWFKHGHDFKWLPHWKHEXWWRQLVWRXFKHG*User Name: Select when you want to protect the user name only.*System: Select when you want to protect all the set data.:KHQWKHXVHU,'EXWWRQLVWRXFKHGD3,1LQSXWVFUHHQDSSHDUV,QSXWD3,1RIXSWRGLJLWV:KHQWKH5HWXUQNH\LVWRXFKHGWKHGLVSOD\UHWXUQVWRWKHSUHFHGLQJVFUHHQ:KHQWKHWUDQVPLWWHUSRZHULVWXUQHGRIIWKHVHWVHFXULW\PRGHEHFRPHVDFWLYH*When a PIN is set at the user name, it must be entered the next time the User Name screen is opened.When a System PIN is set, a button displaying a key iconappears on the Home screen.When you want to change the setting, touch this button and enter the PIN.,I\RXZDQWWRQXOOLI\\RXUFXUUHQWSDVVZRUGVHWWKHSDVVZRUGWRGHIDXOWYDOXH$

$46 <System Menu>85%Switch LockLeverSW Type Posi. Ait/Mom 3P Mom3Posi. Alt.LeverSB 2Posi. Alt.LeverSC 3Posi. Alt.LeverSD 3Posi. Alt.LeverSESW Type Posi. Ait/Mom 3P Mom3Posi. Alt.LeverSF 2Posi.2Posi.2Posi.Alt.LeverSG Alt.LeverSH Mom.SASwitch selection6HOHFWWKHVZLWFKW\SHE\WRXFKLQJWKH>W\SH@EXWWRQFRUUHVSRQGLQJWRWKHVZLWFKWREHUHSODFHG>/HYHU@7RJJOHVZLWFK>%XWWRQ@3XVKEXWWRQ>'LDO@.QREŏ6HWWLQJIRUWRJJOHVZLWFKLVVKRZQDERYH2/3 position selection7RXFKWKH3RVLEXWWRQFRUUHVSRQGLQJWRWKHVZLWFKDQGVHOHFWWKHSRVLWLRQW\SH>3RVL@SRVLWLRQ>3RVL@SRVLWLRQSwitch 7RJJOHVZLWFKW\SHVHWWLQJ6HWWLQJZKHQWKHVZLWFKZDVUHSODFHGIf you modify the location of the switches on the right and left (top) of the transmitter, you should be sure to re-assign functions to the switches for proper operation.A “Lock” is included to prevent settings from being modified by mistake. When you need to change settings, unlock this by pressing “Lock” it will then read ”Unlock” and you can make changes as required.ŏ7RXFKWKH>6ZLWFK@EXWWRQDWWKH6\VWHP0HQXWRFDOOWKHVHWXSVFUHHQVKRZQEHORZŏ5HWXUQWR6\VWHP0HQX[Alt/Mom] mode selection6HOHFWWKHRSHUDWLRQPRGHE\WRXFKLQJWKH>$OW0RP@EXWWRQFRUUHVSRQGLQJWRWKHVZLWFK>$OW@$OWHUQDWHW\SH>0RP@6HOIUHWXUQW\SHŏ6HOHFWLRQRIWKH>0RP@PRGHZLWKDSRVLWLRQW\SHVZLWFKLVVKRZQDERYH"3P Mom" mode selection6HOHFWWKHRSHUDWLRQPRGHE\WRXFKLQJWKH30RPEXWWRQFRUUHVSRQGLQJWRWKHVZLWFK>6LQJOH@2QHVLGHVHOIUHWXUQW\SH>'XDO@%RWKGLUHFWLRQVVHOIUHWXUQW\SH$

$47<System Menu>Operation direction reversal method7RXFKWKHVHWWLQJEXWWRQFRUUHVSRQGLQJWRWKH+:+DUGZDUH\RXZDQWWRUHYHUVH5HYHUVHWKH+:E\WRXFKLQJ><HV@:KHQ\RXZDQWWRVWRSRSHUDWLRQWRXFK>1R@>1RUPDO@1RUPDORSHUDWLRQGLUHFWLRQ>5HYHUVH@5HYHUVHVWKHRSHUDWLRQGLUHFWLRQH/W Setting 6WLFNVZLWFKWULPOHYHUDQGNQRERSHUDWLRQGLUHFWLRQUHYHUVDO+DUGZDUHUHYHUVH6WLFNUHVSRQVHDQGKLVWHULVLVDGMXVWPHQW6WLFN6HWWLQJ&DOLEUDWLRQThis function is for adjusting the sticks, switches, and trimmers characteristics. It is not used without necessity.H/W ReverseThis function reverses the operation signal of the sticks, switches, trimmer levers, and knobs.Note: This setting reverses the actual operationsignal, but does not change the display ofthe indicators on the display. Use the Normalmode as long as there is no special reason touse the Reverse mode.ŏ7RXFKWKH>+:6HWWLQJ@EXWWRQDWWKH6\VWHP0HQXWRFDOOWKHVHWXSVFUHHQVKRZQEHORZŏ5HWXUQWR6\VWHP0HQXStick SettingThis function sets the servo response and hysteresis for stick operation for each condition.The control feeling of the stick can be adjusted tomatch the aerobatics. CalibrationUsually, this calibration is unnecessary. Please perform this calibration, if a gap of a stick should arise in prolonged use.ŏ7RXFKWKH>+:5HYHUVH@EXWWRQDWWKH+:6HWWLQJ0HQXWRFDOOWKHVHWXSVFUHHQVKRZQEHORZŏ5HWXUQWR+:6HWWLQJ0HQX$

$48 <System Menu>Response adjustment7RXFKWKHVHWWLQJEXWWRQFRUUHVSRQGLQJWRWKHVWLFNZKRVHUHVSRQVH\RXZDQWWRDGMXVW$GMXVWPHQWEXWWRQVDSSHDURQWKHULJKWKDQGVLGHRIWKHVWLFNVHWXSVFUHHQ8VHWKHDGMXVWPHQWEXWWRQVWRDGMXVWWKHUHVSRQVH,QLWLDOYDOXH$GMXVWPHQWUDQJHa:KHQWKHDGMXVWPHQWYDOXHLVODUJHWKHUHVSRQVHEHFRPHVVORZHow to Calibration $VWLFNWRFDUU\RXWDFDOLEUDWLRQE\ULJKWDQGOHIWLVFKRVHQ7KHVWLFNLVPDGHQHXWUDODQGD>QHXWUDO@EXWWRQLVSXVKHG7KHVWLFNLVPDGHIXOOULJKWDQGIXOOERWWRPWKH>5LJKW%RWWRP@EXWWRQLVSXVKHG(7KHGLUHFWLRQRIDQDUURZ7KHVWLFNLVPDGHIXOOOHIWDQGIXOOWRSWKH>/HIW7RS@EXWWRQLVSXVKHG(7KHGLUHFWLRQRIDQDUURZŏ7RXFKWKH>6WLFN6HWWLQJ@EXWWRQDWWKH+:6HWWLQJ0HQXWRFDOOWKHVHWXSVFUHHQVKRZQEHORZŏ7RXFKWKH>&DOLEUDWLRQ@EXWWRQDWWKH+:6HWWLQJ0HQXWRFDOOWKHVHWXSVFUHHQVKRZQEHORZŏ5HWXUQWR+:6HWWLQJ0HQXŏ*URXSVLQJOHPRGHVZLWFKLQJ*U6QJO(For more information, see the description at the back of this manual.)Hysteresis adjustment7RXFKWKHVHWWLQJEXWWRQFRUUHVSRQGLQJWRWKHVWLFNZKRVHK\VWHUHVLV\RXZDQWWRDGMXVW$GMXVWPHQWEXWWRQVDSSHDURQWKHULJKWKDQGVLGHRIWKHVWLFNVHWXSVFUHHQ8VHWKHDGMXVWPHQWEXWWRQVWRDGMXVWWKHK\VWHUHVLV,QLWLDOYDOXH$GMXVWPHQWUDQJHa:KHQWKHDGMXVWPHQWYDOXHLVODUJHWKHK\VWHUHVLVYDOXHEHFRPHVODUJHŏ5HWXUQWR+:6HWWLQJ0HQX*Please do not push a stick too much strongly.*An after-end should check that the neutral 0% and bottom right side will be +100%, and the top left side has become -100%.$

$49<System Menu>Model 1 85%Sound Volume-+-+-+-+Key OperationTrim & Center ClickError/WarningTimer EventSound Volume 6RXQG9ROXPHVHWWLQJThis function can set the volume of "KeyOperation" "Error/Warning" "Trim&Center Click" "Timer Event" respectively.*Set the PIN carefully. When a system PIN is set, if you forget the PIN, none of the settings can be changed. In this case, the system must be reset by the Futaba Service Center. ŏ7RXFKWKH>6RXQG9ROXPH@EXWWRQDWWKH6\VWHP0HQXWRFDOOWKHVHWXSVFUHHQVKRZQEHORZŏ5HWXUQWR6\VWHP0HQXSound Volume Setting method:KHQWKH6RXQG9ROXPHER[LVWRXFKHGDNH\ERDUGDSSHDUVRQWKHVFUHHQ3OHDVHFKDQJHWKHVRXQGYROXPHWRWKHIDYRUWRXFKLQJWKHEXWWRQRIIRXULWHPV*If it touches "+", the volume of the item grows.*If it touches "-", the volume of the item becomes small.$

$50 <System Menu>Music playback7KH70=WUDQVPLWWHUFDQSOD\EDFNWKHZPDPXVLF¿OHVVWRUHGLQWKH6'FDUGDQG86%PHPRU\You can listen to them through the built-in speaker or a headphone by the earphone plug.[Important notice]%HIRUHGRZQORDGLQJ¿OHVIURP\RXU3&LQWRWKHSD card, insert the SD card into the transmitter and turn on the power of the transmitter. Then the following folders will be automatically FUHDWHGLQWKH6'FDUG:KHQ\RXGRZQORDG¿OHVIURP\RX3&FRS\DQGSDVWHWKH¿OHVLQWRWKHLUFRUUHVSRQGLQJ¿OHV%03SLFWXUHÀOHV:0$PXVLFÀOHV:$9VRXQGÀOHV02'(/PRGHOGDWDÀOHV3XVKWKH0XVLF3OD\EDFNEXWWRQRQWKHKRPHVFUHHQWRFDOOWKHIROORZLQJVHWXSVFUHHQ5HWXUQWRWKHKRPHVFUHHQ%XWWRQWRVHOHFWHLWKHU2QHWLPH3OD\EDFNRU5HSHDW3OD\EDFN%XWWRQWRVHOHFWHLWKHU2QH0XVLF3OD\EDFNRU0XOWLSOH0XVLF3OD\EDFN6:VHOHFWLRQEXWWRQ3XVKWKLVEXWWRQWRFDOOWKH6:VHOHFWVFUHHQDQGFKRRVHWKH0XVLFSOD\EDFNVZLWFK5HIHUWRWKHGHVFULSWLRQLQWKHHQGRIWKLVPDQXDOButtons for music playback<RXFDQSOD\EDFNDQ\PXVLFILOHVOLVWHGRQWKHULJKWVLGHRIWKHVFUHHQ,I\RXDGMXVWWKHYROXPHKHUHLWDGMXVWVQRWRQO\PXVLFSOD\EDFNEXWDOVRRWKHUDSSOLFDWLRQVTo playback$OOWKHPXVLFÀOHVVDYHGLQWKH&)FDUGZLOOEHVKRZQKHUH3XVKWKHILOHQDPHWRVHOHFWWKHPXVLFILOH\RXZDQWWRKHDU8VHWKHEXWWRQVRQWKHOHIWWRSOD\EDFNRUVWRSWKHPXVLF3OD\EDFNÀOHOLVWPlayback FileFile not found !Model 185%00:00:00 / 00:00:00Sel.SWPlayer-+Player$

$51<System Menu>85%CameraThumbnailModel1Save to...Shooting method7XUQRQWKHWUDQVPLWWHUDQGFDOO>&DPHUD@IURPWKH6\VWHP0HQX6HOHFWWKHSLFWXUHVDYHGHVWLQDWLRQ70=6'FDUG86%PHPRU\*When an SD card and USB memory are connected, an icon is displayed and can be selected.3RLQWWKHFDPHUDDWWKHEDFNRIWKHWUDQVPLWWHUWRZDUGWKHVXEMHFWDQGSUHVVWKHVKXWWHUEXWWRQ7KHSLFWXUHFDQEHFKHFNHGZLWKWKH>7KXPEQDLO@EXWWRQ$SLFWXUHFDQEHFRSLHGDQGGHOHWHGE\SUHVVLQJLWDisplay pictures at the model data&DOO>&DPHUD@IURPWKH6\VWHP0HQX0DNHWKHVDYHGHVWLQDWLRQWKHVDPHSODFHDVPRGHOGDWD,IDQ6'FDUGRU86%PHPRU\LVQRWFRQQHFWHGWKH70=EHFRPHVWKHLQLWLDOVWDWH7DNHWKHSLFWXUH\RXZDQWWRGLVSOD\ZLWKWKH70=3RVLWLRQWKHSLFWXUHLQVLGHWKHIUDPH6HOHFWWKHPRGHOZKRVHSLFWXUH\RXZDQWWRSDVWHEHIRUHKDQG3UHVV>7KXPEQDLO@DQGWKHQSUHVVWKHSLFWXUH\RXWRRNHDUOLHU3UHVV>(QWU\@7KHPHVVDJH´6XUH"µLVGLVSOD\HG3UHVV><HV@Camera &DPHUDSKRWRJUDSK\DQGSLFWXUHVWRUDJHPictures can be easily taken with the camera in the T18MZ. The picture can be saved to the T18MZ, SD card, and USB memory. Your favorite model photographed by you can be displayed on the Home screen, Start screen, and Model Select screen.ŏ&DOOWKHIROORZLQJVHWWLQJVFUHHQE\SUHVVLQJWKH>&DPHUD@EXWWRQLQWKH6\VWHP0HQXŏ5HWXUQWR6\VWHP0HQXŏ3LFWXUHGDWDVDYHGHVWLQDWLRQ70=6'FDUG86%PHPRU\7RWKHVFUHHQRIDWKXPEQDLOŏVKXWWHUEXWWRQCamera$

$52 <System Menu>85%S.BUS ServoServoTypeSoftStartStopModeNORMRecallReverseNeutral2íVHWDeadBandBoost+0.000.030.0SmootherSpeedControlTrave lAdjustDamperFactorStretcherGain100.0ACT 12.0000.001CH 0 0 INHIDModel 1100.0NORMFREEOFFOFFProcedure for changing S.BUS servo setting6HOHFW>6%866HUYR@RIWKH6\VWHP0HQX:LUHWKHVHUYRDVVKRZQLQWKHÀJXUHDERYH3UHVV>5HFDOO@7KH,'DQGFXUUHQWVHWWLQJRIWKDWVHUYRDUHGLVSOD\HG:KHQPXOWLSOHVHUYRVDUHFRQQHFWHGFKDQJH>,1+@DWWKHULJKWVLGHRIWKH,'QXPEHURQWKHVFUHHQWR>$&7@DQGHQWHUWKH,'RIWKHVHUYR\RXZDQWWRVHW6HWHDFKLWHP3OHDVHVHHWKHQH[WSDJH3UHVV>:ULWH@7KHVHWWLQJVDUHFKDQJHGS.BUS Servo 6%86VHUYRVHWWLQJAn S.BUS servo can memorize the channel and various settings itself. Servo setting can be performed on the T18MZ screen by wiring the servo as shown in the figure.ŏ&DOOWKHIROORZLQJVHWWLQJVFUHHQE\SUHVVLQJWKH>6%866HUYR@EXWWRQLQWKH6\VWHP0HQXŏ5HWXUQWR6\VWHP0HQXHUBor Y-adapterS.BUS servo Receiver BatteryƔ6HUYR,'QXPEHUIndividual ID numbers are memorized at the S.BUS servos. When one servo is set as shown at the right, the servo ID number is automatically read. However, when you do not want to change one setting of multiple servos mounted to the fuselage, only thedesired servo in the multi-connection state can be set by entering the ID of that servo.$

$53<System Menu>S.BUS Servo Description of function of each parameter,'Displays the ID of the servo whose parameters are to be read. It cannot be changed.&KDQQHOChannel of the S.BUS system assigned to the servo. Always assign a channel before use.5HYHUVHThe direction in which the servo rotates can be changed.6HUYRW\SHWhen “Retractable” is selected and the servo has been continuously stopped for 30 seconds, the dead band expands and unnecessary hold current due to external force is eliminated. When a new control signal enters, normal operation is resumed. When using the servo as a landing gear servo, select “Retractable”. Also adjust the servo travel to match the landing gear movement range.6RIW6WDUWRestricts operation in the speciﬁed direction the instant the power is turned on. By making this setting, only the ﬁrst operation when the power is turned on slowly moves the servo to the speciﬁed position.6WRS0RGHThe state of the servo when the servo input signal is lost can be speciﬁed. The "Hold" mode setting holds the servo in its last commanded position even if using AM or FM system.6PRRWKHUThis function changes smoothness of the servo operation relative to operation signal changes. Normally use at Smooth setting. Especially, select the "OFF" mode when quick operation is necessary.1HXWUDO2IIVHWThe neutral position can be changed. When the neutral offset is large value, the servo's range of travel is restricted on one side.6SHHG&RQWUROSpeeds can be matched by specifying the operating speed. The speed of multiple servos can be matched without being affected by motor ﬂuctuations. This is effective for load torques below the maximum torque.However, note that the maximum speed will not be exceeded even if a speed over the maximum speed of the servo at each operating voltage is set.'HDGEDQGThe dead band angle at stopping can be speciﬁed.[Relationship between dead band set value and servo operation]Small ĺ Dead band angle is small and the servo is immediately operated by a small signal change.Large ĺ Dead band angle is large and the servo does not operate at small signal changes.(Note) If the dead band angle is too small, the servo will operate continuously and the current consumption will increase and the life of the servo will be shortened.7UDYHO$GMXVWThe left and right travels centered about the neutral position can be set independently.%RRVWThe minimum current applied to the internal motor when starting the servo can be set. Since a small travel does not start the motor, it essentially feels like the dead band was expanded. The motor can be immediately started by adjusting the minimum current which can start the motor.[Relationship between boost set value and servo operation]Small ĺ Motor reacts to a minute current and operation becomes smooth.Large ĺ Initial response improves and output torque increases. However, if the torque is too large, operation will become rough.'DPSHUThe characteristic when the servo is stopped can be set.When smaller than the standard value, the characteristic becomes an overshoot characteristic. If the value is larger than the standard value, the brake is applied before the stop position.$

54 <System Menu>Especially, when a large load is applied, overshoot, etc. are suppressed by inertia and hunting may occur, depending on the conditions. If hunting (phenomena which cause the servo to oscillate) occurs even though the Dead Band, Stretcher, Boost and other parameters are suitable, adjust this parameter to a value larger than the initial value.[Relationship between damper set value and servo operation]Small ĺ When you want to overshoot. Set so that hunting does not occur.Large ĺ When you want to operate so that braking is not applied. However, it will feel like the servo response has worsened.(Note) If used in the hunting state, not only will the current consumption increase, but the life of the servo will also be shortened.6WUHWFKHUThe servo hold characteristic can be set.The torque which attempts to return the servo to the target position when the current servo position has deviated from the target position can be adjusted.This is used when stopping hunting, etc., but the holding characteristic changes as shown below.[Relationship between stretcher and servo operation]Small ĺ Servo holding force becomes weaker.Large ĺ Servo holding force becomes stronger.(Note) When this parameter is large, the current consumption increases.

$55<System Menu>Model 1 85%InformationVersionWindowsCE Ver. 6.0 (0)Editor Ver. 0.1.0EncoderEnglishVer. 0.1Memory Size 0 MBFree Space 0 MBModel data 0 model0 MB0 MB0 modelSD CardLanguageUSB MemoryProduct IDArea000000000AmericaInformation7KHSURJUDPYHUVLRQ&)FDUG86%PHPRU\GDWDDQGSURGXFW,'DUHGLVSOD\HG7KHODQJXDJHXVHGE\WKHV\VWHPFDQDOVREHFKDQJHGThe Information screen displays the T18MZ system program version information, T18MZ ,SD card and USB memory (memory size, vacant capacity, number of model data, and number of PXVLF¿OHVLQIRUPDWLRQDQGSURGXFW,'The language (Japanese, English) used on the screen can also be changed.ŏ7RXFKWKH>,QIRUPDWLRQ@EXWWRQDWWKH6\VWHP0HQXWRFDOOWKHVHWXSVFUHHQVKRZQEHORZŏ5HWXUQWR6\VWHP0HQX*When an SD card and USB memory are not inserted, their information is not displayed.ŏ6HOHFWDEOHIRU/DQJXDJH$

$56 <System Menu>Range Check %HIRUHDÁLJKWJURXQGUDQJHFKHFNThe 'range check mode' reduces the transmission range of the radio waves to allow for a ground range check.*The range check mode, when activated, will continue for 90 seconds unless the user exits this mode early. When the progress bar reaches 90s, the RF transmission automatically returns to the normal operating power.ŏ3XVKWKH>6@.H\→7XUQ21WKHWUDQVPLWWHUVSRZHUVZLWFK[12@LVSXVKHGŏ[<HV@LVSXVKHGWarningDo not fly in the range check mode. *Since the range of the radio waves is short, if the model is too far from the transmitter, control willbe lost and the model will crash.Rotation Range Check method3XVKWKH>6@.H\→7XUQ21WKHWUDQVPLWWHUVSRZHUVZLWFK6HOHFW>1R@*For safety, the RANGE CHECK mode can not be selected while the RF transmission is active.,QWKHV\VWHPPHQXFKRRVHWKH5DQJH&KHFNVHOHFWLRQIURPWKHPHQXRSWLRQV7KH5DQJH&KHFNVFUHHQLVGLVSOD\HG7RDFWLYDWHWKH5DQJH&KHFNPRGHSUHVVWKH><HV@EXWWRQ'XULQJWKH5DQJH&KHFNSHULRGWKH5)SRZHULVUHGXFHGWRDOORZWKHJURXQGUDQJHWHVWVWREHSHUIRUPHG7KH5DQJH&KHFNIXQFWLRQDXWRPDWLFDOO\H[LWVDIWHUWKHVHFRQGWLPHOLPLWKDVH[SLUHG7KHSURJUHVVEDULVGLVSOD\HGRQWKHWUDQVPLWWHUVVFUHHQ6KRXOG\RXFRPSOHWHWKHUDQJHFKHFNEHIRUHWKHVHFRQGVKDVSUHVVHGSUHVVWKH>([LW@EXWWRQ*When the [RESTART] botton is pressed, the range check mode timer is returned to 0.*Please note, upon expiration of the 90 seconds, orwhen [Exit] is selected, the transmitter willautomatically return to the normal RF operation asnoted on the display.*Once the 18MZ is transmitting at full power, it isnot possible to enter the Range Check modeZLWKRXW¿UVWVZLWFKLQJWKHWUDQVPLWWHU2IIDQGback On. This has been designed to prevent aPRGHOHUIURPLQDGYHUWHQWO\À\LQJLQWKH5DQJHCheck mode.:KHQWKH>([LW@EXWWRQLVSUHVVHGWKH5DQJH&KHFNPRGHLVGLVDEOHGDQGWKH0=ZLOOEHJLQWUDQVPLWWLQJDWIXOOSRZHU*After exiting the Range Check mode, thefunction cannot be selected again. To select theRange Check mode again you must cycle thetransmitter power switch.ŏ7RXFKWKH>5DQJH&KHFN@EXWWRQDWWKH6\VWHP0HQXWRFDOOWKHVHWXSVFUHHQVKRZQEHORZ$

$57<Model Basic Setting Procedure>MODEL BASIC SETTING PROCEDURE1. Model addition and callInitial setting assigns 1 model to the T18MZtransmitter. The Model Select function of the Linkage Menu is used to add models and to call models which are already set.This is convenient when calling a model after its name has been registered. (Data can also be saved tothe accessory SD card and USB memory)The currently called model name is displayed at the top of the screen. Before flying and before changing DQ\VHWWLQJVDOZD\VFRQ¿UPWKHPRGHOQDPHWhen a new model was added, the Model typeselect screen/System mode/Receiver link automatically appear. Please be aware that the transmitter will stop transmitting when you change the model. 2. Model type selectionSelect the model type matched to the fuselage with the Model Type select function of the Linkage Menu.For an airplane, select the model type from among the 3 types: airplane, glider, and motor glider. When theWing type select screen is displayed and the wing type is selected when selecting the model type, the Tail typeselect screen is displayed. Select the tail type matched to the fuselage. There are 13 wing types and 3 tail types for airplane, glider, and motor glider.Airplane/glider basic setting procedure3. Fuselage linkageLink the ailerons, elevators, throttle, rudder, etc. in accordance with the model's instruction manual. For a description of the connection method, see the Receiver and Servos Connection.Note: The channel assignment of the T18MZ is different from that of our existing systems. Note that even for the same "airplane model", when the wing type and tail type are different, the channel assignment may be different. (The channel assigned to each function can be checked at the Function menu of the Linkage Menu.)ŏ:KHQWKHGLUHFWLRQRIWKHOLQNDJHLVUHYHUVHGDGMXVWWKHGLUHFWLRQZLWKWKH5HYHUVHIXQFWLRQRIWKH/LQNDJH0HQXŏ&RQQHFWWKHWKURWWOHOLQNDJHVRFDUEXUHWRULVRSHQDWIXOOWULPDQGIXOORSHQWKHQWKHWKURWWOHFDQEHFXWŏ$GMXVWWKHQHXWUDOSRVLWLRQDQGUXGGHUDQJOHZLWKWKHOLQNDJHDQGILQHWXQHWKHPZLWKWKH6XE7ULPDQG(QG3RLQWIXQFWLRQVUXGGHUDQJOHDGMXVWPHQW7RSURWHFWWKHOLQNDJHDOLPLWSRVLWLRQFDQDOVREHVHWZLWKWKH(QG3RLQWIXQFWLRQ7KH(QG3RLQWIXQFWLRQFDQDGMXVWWKHDPRXQWRIXSGRZQDQGOHIWULJKWPRYHPHQWOLPLWDQGVHUYRVSHHGRIHDFKFKDQQHO$

$58 <Model Basic Setting Procedure>4. Throttle cut settingThrottle cut can be performed with one touch by a switch without changing the throttle trim position.Set throttle cut with the Throttle Cut function of the Linkage Menu. After activating the throttle cut function and selecting the switch, adjust the throttle position so that the carburetor becomes full open. For safety, the throttle cut function operates the throttle stick in the slow position.5. Idle down settingThe idling speed can be lowered with one touch by a switch without changing the throttle trim position.Perform this setting with the Idle Down function of the Linkage Menu. After activating the Idle Down function and selecting the switch, adjust the idle down speed.For safety, the idle down function acts only when the throttle stick is in the slow position.*While the Throttle Cut function is in operation, the Idle Down function does not work.6. AFR (D/R)AFR function is used to adjust the throw and operation curve of the stick, lever, and switch functions for each flight condition. This is normally used after End Point (ATV) has defined the maximum throw directions (End Point acts on ALL flight condition settings). When mixing is applied from one channel toanother channel, both channels can be adjusted at the same time by adjusting the operation rate through the AFR function.7. AirbrakeThis function is used when an air brake is necessary when taking off or diving, etc.The preset elevators and flaps (camber flap, brakeÀDSRIIVHWDPRXQWFDQEHDFWLYDWHGE\DVZLWFK7KHRIIVHWDPRXQWRIWKHDLOHURQHOHYDWRUDQGÀDSservos can be adjusted as needed. Also the speed of the DLOHURQHOHYDWRUDQGÀDSVHUYRVFDQEHDGMXVWHG,1side/OUT side) A delay can be set for each condition, and a Cut switch which will turn OFF the delay can EHFKRVHQ7ULPDPRXQWVFDQEH¿QHWXQHGE\VHWWLQJa VR You can also set the Auto Mode, which will link Airbrake to a stick, switch, or dial. A separate stick VZLWFKRUGLDOFDQDOVREHVHWDVWKH212))VZLWFK$GGLWLRQRIÀLJKWFRQGLWLRQVThe transmitter can install up to eight flight conditions per model. You can assign all switches including sticks, switches, trim levers and trim VZLWFKHVDVÀLJKWFRQGLWLRQVHOHFWLRQVZLWFKHV<RXcan also add delayed mixing to these functions in order to avoid sudden changes. Moreover, you can VHWSULRULW\RUGHUIRUÀLJKWFRQGLWLRQVZKHQ\RXVHWmore than one condition. In addition, you can copy conditions and/or change names of conditions. ThisFRPPDQGPD\DOVREHXVHGWRGH¿QHZKDWVZLWFKHVand/or controls are used to activate each flight condition.The Condition Select function automatically allocates the Condition 1 for each model type.Condition 1 is the default condition, also referred to DV1RUPDODQGLVWKHRQO\RQHDFWLYHZKHQDQHZPRGHOW\SHLVGH¿QHG7KLVFRQGLWLRQLVDOZD\VRQand remains on until other conditions are activated by switches.The Condition Delay can be programmed for each channel. The Condition Delay is used to change theservo throw smoothly when switching conditions.*When a new condition is added, "Condition1" data is automatically copied.*Select the condition switch and set the new condition data in the VZLWFK21VWDWH+RZHYHULIWKHJURXSPRGH*UZDVVHOHFWHGLQadvance, the same data will be input at all the conditions. Select the single mode (Sngl) and adjust the condition you want to change.$

$59<Model Basic Setting Procedure>1. Model addition and callDefault setting assigns 1 model to the T18MZ. Toadd new models or to call a model already set, use the Model Select function of the Linkage Menu.This is convenient when calling a model after registering the model names in advance. (Data can also be saved to the accessory SD card and USB memory)The currently called model is displayed at the topRIWKHVFUHHQ%HIRUHÀ\LQJDQGEHIRUHFKDQJLQJDQ\VHWWLQJVDOZD\VFRQ¿UPWKHPRGHOQDPHPlease be aware that the transmitter will stop transmitting when you change the model. When a new model was added, the Model type select screen/System mode/Receiver link automatically appear. Please be aware that the transmitter will stop transmitting when you change the model.2. Model type and swash type selectionWhen a separate model type is already selected,select helicopter with the Model Type function of theLinkage Menu, and then select the swash type matched to the fuselage.Helicopter basic setting procedure3. Flight condition additionThe transmitter can install up to eight flight conditions per model. You can assign all switchesincluding sticks, switches, trim levers and trim switchesDVIOLJKWFRQGLWLRQVHOHFWLRQVZLWFKHV<RXFDQDOVRadd delayed mixing to these functions in order to avoid sudden changes. Moreover, you can set priority RUGHUIRUÀLJKWFRQGLWLRQVZKHQ\RXVHWPRUHWKDQRQHcondition. In addition, you can copy conditions and/or change names of conditions. This command may alsobe used to define what switches and/or controls are XVHGWRDFWLYDWHHDFKÀLJKWFRQGLWLRQThe Condition Select function automatically allocates the Condition 0 for each model type. Condition 0 is WKHGHIDXOWFRQGLWLRQDOVRUHIHUUHGWRDV1RUPDODQGLVWKHRQO\RQHDFWLYHZKHQDQHZPRGHOW\SHLVGH¿QHGThis condition is always on, and remains on until other conditions are activated by switches.The Condition Delay can be programmed for each channel. The Condition Delay is used to change the servo throw smoothly when switching conditions.*HQHUDOÀLJKWFRQGLWLRQVHWWLQJH[DPSOHŏ1RUPDO8VHLQLWLDOVHWWLQJFRQGLWLRQVRSHUDWHZKHQVZLWFK2))8VHIURPHQJLQHVWDUWLQJWRKRYHULQJŏ,GOHXS6ZLWFKVHWWLQJH[DPSOH2SHUDWHDW6:(FHQWHU8VHLQVWDOOWXUQORRSUROOLQJVWDOOWXUQDQGRWKHUPDQHXYHUVŏ,GOHXS6ZLWFKVHWWLQJH[DPSOH2SHUDWHDW6:(IRUZDUGVLGH8VHLQUROOVŏ7KURWWOHKROG6ZLWFKVHWWLQJH[DPSOH2SHUDWHDW6:*IRUZDUGVLGH8VHLQDXWRURWDWLRQThe priority is throttle hold/idle up 2/idle up 1/normal. Throttle hold has the highest priority.Add other conditions, as required.$

$60 <Model Basic Setting Procedure>ŏ6ZDVKSODWHFRUUHFWLRQ([FHSW+PRGH2SHUDWLRQRIWKHVZDVKSODWHQHDUWKHKRYHULQJSRLQWFDQEHFRUUHFWHGE\VZDVK$)5IXQFWLRQFRUUHFWLRQPL[LQJ8VHWKLVZKHQSLWFKDLOHURQDQGHOHYDWRURSHUDWLRQFDXVHVWKHVZDVKSODWHWRGHYLDWHIURPWKHQRUPDOGLUHFWLRQ&DOOWKH6ZDVKVHWXSĺ6ZDVKGHWDLOVVFUHHQ3LWFKVORZVLGHDQGKLJKVLGHOLQNDJHFRUUHFWLRQLVDOVRSRVVLEOH$GMXVWVRWKDWSLWFKRSHUDWLRQFDXVHVWKHVZDVKSODWHWRPRYHXSDQGGRZQLQWKHKRUL]RQWDOVWDWH5. Throttle curve settingThis function adjusts the pitch operation curve in relation to the movement of the throttle stick for each condition.(17 points curve)The pitch curve can be freely selected from linear operation curve to smooth curve, and adjusted tomatch the curve you want by means of the T18MZ’spowerful Curve Edit Function (6 types of curves can be selected). Up to 17 points can be set for linear RUFXUYHW\SHV+RZHYHUZKHQXVLQJWKHSRLQWVRUSRLQWVVSHFL¿HGWRFUHDWHDFXUYHDVLPSOHDQGsmooth curve can be created by selecting the curvetype and reducing the number of input points to 3or 5, and then entering the specified value at the corresponding points that you created.6HWWLQJH[DPSOH!Call the throttle curve of each condition with the condition select switch.ŏ1RUPDOFXUYHDGMXVWPHQW1RUPDOFXUYHXVHV1RUPDO/LQHDUW\SHDQGFUHDWHVDEDVLFSLWFKFXUYHFHQWHUHGQHDUKRYHULQJ7KLVFXUYHLVDGMXVWHGWRJHWKHUZLWKWKH7KURWWOH&XUYH1RUPDOVRWKDWWKHHQJLQHVSHHGLVFRQVWDQWDQGXSGRZQFRQWUROLVHDVLHVWŏ,GOHXSFXUYHDGMXVWPHQW7KHKLJKVLGHSLWFKFXUYHVHWVWKHPD[LPXPSLWFKUHJDUGOHVVRIWKHHQJLQHORDG7KHORZVLGHSLWFKFXUYHFUHDWHVDFXUYHPDWFKHGIRUDHUREDWLFVORRSUROO'HWF1RWH:KHQWKHFXUYHW\SHLVFKDQJHGWKHGDWDLVUHVHW4. Fuselage linkageConnect the throttle rudder, ailerons, elevators, pitch, and other rudder linkages in accordance with the kit instruction manual. For a description of the connection method, see "Receiver and Servos Connection".7KHFKDQQHODVVLJQPHQWRIWKH70=LVGLIIHUHQWIURPWKDWRIRXUH[LVWLQJV\VWHPV7KHchannel assigned to each function can be checked DWWKH)XQFWLRQPHQXRIWKH/LQNDJH0HQXŏ:KHQWKHGLUHFWLRQRIRSHUDWLRQRIWKHOLQNDJHLVUHYHUVHXVHWKH5HYHUVHIXQFWLRQRIWKH/LQNDJH0HQX$OVRXVHWKHVZDVK$)5IXQFWLRQLQRWKHUWKDQWKH+PRGHŏ$GMXVWWKHGLUHFWLRQRIRSHUDWLRQRIWKHJ\UR*\URVLGHIXQFWLRQŏ&RQQHFWWKHWKURWWOHOLQNDJHVRWKDWWKHFDUEXUHWRUEHFRPHVIXOORSHQDWIXOOWULPWKURWWOHFXWLVSRVVLEOHŏ%DVLFDOO\DGMXVWWKHQHXWUDOSRVLWLRQDQGUXGGHUDQJOHDWWKHOLQNDJHVLGHDQGILQHWXQHZLWKWKH6XE7ULPIXQFWLRQDQG(QG3RLQWIXQFWLRQUXGGHUDQJOHDGMXVWPHQW7RSURWHFWWKHOLQNDJHDOLPLWSRVLWLRQFDQDOVREHVHWZLWKWKH(QG3RLQWIXQFWLRQ$

$61<Model Basic Setting Procedure>&RQÀUPWKDWWKHUDWHRIWKHVORZHVWSRVLWLRQRIWKHVWLFNLVLQLWLDOVHWWLQJ%HVXUHWKDWZKHQVHWWRKLJKVLGHWKHFXUYHRIDQ\FRQGLWLRQGRHVQRWH[FHHGExample of pitch curve setting:&DOOWKHSLWFKFXUYHRIHDFKFRQGLWLRQZLWKWKHFRQGLWLRQVHOHFWVZLWFK*Pitch curve graph display can be switched to pitch angle direct reading display.$3LWFKFXUYH1RUPDO0DNHWKHSLWFKDWKRYHULQJDSSUR[LPDWHO\º~6º6HWWKHSLWFKDWKRYHULQJZLWKWKHVWLFNSRVLWLRQDWWKHSRLQWDVWKHVWDQGDUG*Stability at hovering may be connected to the throttle curve. Adjustment is easy by using the hovering throttle function and hovering pitch function together.%3LWFKFXUYH,GOHXS7KHLGOHXSSLWFKFXUYHIXQFWLRQFUHDWHVDFXUYHPDWFKHGWRDLUERUQHÁLJKW6HWWRºaºDVVWDQGDUG&3LWFKFXUYH,GOHXS7KHKLJKVLGHSLWFKVHWWLQJLVOHVVWKDQLGOHXS7KHVWDQGDUGLVº'3LWFKFXUYH+ROG$WDXWRURWDWLRQXVHWKHPD[LPXPSLWFKDWERWKWKHKLJKDQGORZVLGHV>3LWFKDQJOHVHWWLQJH[DPSOH@7KURWWOHKROGºaº6. Throttle hold setting&DOOWKH7KURWWOH+ROGIXQFWLRQIURPWKH0RGHOMenu and switch to the throttle hold condition with the condition select switch.1RWH$WLQLWLDOVHWWLQJWKHVHWWLQJPRGHLVWKHJURXSPRGH6LQFHWKLVIXQFWLRQLVQRWXVHGDWRWKHUFRQGLWLRQVVZLWFKWRWKHVLQJOHPRGHEHIRUHVHWWLQJŏ6HWWLQJWRWKHVWDWHZKLFKDFWLYDWHVWKHIXQFWLRQ7KHWKURWWOHKROGIXQFWLRQDOORZVVHWWLQJIRUWKURWWOHFXWDQGVZLWFKLQJRIWKHIXQFWLRQÀ[HGDWWKHLGOHSRVLWLRQE\VZLWFKIRUWUDLQLQJ(LWKHURQHRUERWKIXQFWLRQVFDQEHSHUIRUPHGŏ+ROGSRVLWLRQVHWWLQJ7KLVIXQFWLRQVHWVWKHVHUYRRSHUDWLRQSRVLWLRQDWWKURWWOHKROG7KURWWOHFXWDQGLGOHSRVLWLRQVŏ2WKHUVHWWLQJV:KHQ\RXZDQWWROLQNRSHUDWLRQZLWKVWLFNPDQLSXODWLRQWKH$XWRPRGHFDQEHVHW:KHQ\RXZDQWWRDGMXVWWKHVHUYRVSHHGDGMXVW>6SHHG@3LWFKWR58'PL[LQJVHWWLQJUse this function when you want to suppressthe torque generated by the changes in the pitch and speed of the main rotor during pitch operation. Adjust it so that the nose does not swing in the UXGGHUGLUHFWLRQ+RZHYHUZKHQXVLQJDKHDGLQJhold gyro like those shown below, do not use Pitch to RUD mixing.1RWH:KHQXVLQJD*<*<*<*<RURWKHUKHDGLQJKROGJ\URWKLV3LWFKWR58'PL[LQJVKRXOGQRWEHXVHG7KHUHDFWLRQWRUTXHLVFRUUHFWHGDWWKHJ\URVLGH:KHQRSHUDWLQJWKHJ\URLQWKH$9&6PRGHWKHPL[HGVLJQDOZLOOFDXVHQHXWUDOGHYLDWLRQV\PSWRPVDQGWKHJ\URZLOOQRWRSHUDWHQRUPDOO\Call the Pitch to RUD mixing function from the Model Menu, and set the curve for each condition. $WLQLWLDOVHWWLQJWKLVIXQFWLRQLVLQWKH,1+VWDWH7RXVHLWVHWLWWRWKH21VWDWH(17 points curve)Curve setting of up to 17 points is possible. +RZHYHULQWKHIROORZLQJVHWWLQJH[DPSOHDsimple curve can be adjusted by using the [Linear] curve type.1RWH$WLQLWLDOVHWWLQJWKHVHWWLQJPRGHLVWKHJURXSPRGH,QWKLVPRGHWKHVDPHFRQWHQWVDUHVHWDWLQDOOFRQGLWLRQV:KHQ\RXZDQWWRVHWWKHVHOHFWHGFRQGLWLRQRQO\VZLWFKWRWKHVLQJOHPRGH6HWWLQJH[DPSOH!Call the mixing curve of each condition with the condition select switch.ŏ7KURWWOHKROGFXUYHDGMXVWPHQW7KHWKURWWOHKROGFXUYHLVXVHGZKHQSHUIRUPLQJDXWRURWDWLRQGLYHV$

$62 <Model Basic Setting Procedure>$FXUYHVHWWLQJH[DPSOHLVVKRZQEHORZ$3LWFKWR58'PL[LQJFXUYH1RUPDO8VHWKHKRYHULQJV\VWHPDQGVHWWKLVFXUYHWRPDWFKWDNHRIIDQGODQGLQJDQGYHUWLFDOFOLPEDWDFRQVWDQWVSHHG*For this curve, use the initial setting [Linear] curve type and adjust the left and right rates in the [Separate] mode.%3LWFKWR58'PL[LQJ,GOHXS8VHWKLVFXUYHLQºVWDOOWXUQORRSDQGUROOLQJVWDOOWXUQDQGDGMXVWLWVRWKHIXVHODJHLVIDFLQJVWUDLJKWDKHDGZKHQKHDGLQJLQWRWKHZLQG*For this curve, [Linear] curve type can be used and the entirecurve can be lowered with the [Offset] button.&3LWFKWR58'PL[LQJ+ROG7KLVIXQFWLRQLVVHWVRWKDWWKHIXVHODJHLVIDFLQJVWUDLJKWDKHDGDWVWUDLJKWOLQHDXWRURWDWLRQ7KHSLWFKRIWKHWDLOURWRUEHFRPHVQHDUO\º*For this curve, [Linear] curve type can be used and the entirecurve can be lowered with the [Offset] button.ŏ2WKHUVHWWLQJV7KHPL[LQJULVHFKDUDFWHULVWLFDWSLWFKRSHUDWLRQFDQEHDGMXVWHG$QDFFHOHUDWLRQ$&/5IXQFWLRQZKLFKWHPSRUDULO\LQFUHDVHDQGGHFUHDVHWKHPL[LQJDPRXQWFDQEHVHW6ZDVK0L[FRUUHFWVDLOHURQHOHYDWRUDQGpitch interactionThe swash mix function is used to correct the swash plate in the aileron (roll) direction and elevator (cyclic pitch) corresponding to each operation of each condition.7KURWWOHPL[LQJVHWWLQJRPM loss caused by swash operation at aileron or elevator operation can be corrected with the7KURWWOH0L[IXQFWLRQRIWKH0RGHO0HQX+RZclockwise and counterclockwise torque is applied when pirouetting can also be corrected.*\URVHQVLWLYLW\DQGPRGHVZLWFKLQJThe gyro sensitivity and mode switching function is dedicated gyro mixing of the ModelMenu, and can be set for each condition.ŏ1RUPDOFRQGLWLRQKRYHULQJ*\URVHQVLWLYLW\PD[LPXPŏ,GOHXS,GOHXS7KURWWOHKROG*\URVHQVLWLYLW\PLQLPXPŏ+RZHYHUDWDXWRURWDWLRQRIDWDLOGULYHQKHOLFRSWHUWKLVIXQFWLRQPD\QRWKDYHDQ\DIIHFWDWKLJKJ\URVHQVLWLYLW\11. Throttle cut settingThrottle cut provides an easy way to stop the HQJLQHE\ÀLSSLQJDVZLWFKZLWKWKHWKURWWOHVWLFNat idle. The action is not functional at high throttle to avoid accidental dead sticks. The switch’s location and direction must be chosen, as it defaults WR18//*With throttle stick at idle, adjust the cut position until the engine consistently shuts off, but throttle linkage is not binding. When finished, touch the “Throttle Cut” button to exit.2WKHUVSHFLDOPL[LQJVŏ3LWFKWR1HHGOHPL[LQJ7KLVPL[LQJLVXVHGZLWKHQJLQHVZLWKDFRQVWUXFWLRQZKLFKDOORZVQHHGOHFRQWUROGXULQJÁLJKWIXHODLUPL[WXUHDGMXVWPHQW$QHHGOHFXUYHFDQEHVHW7KHQHHGOHVHUYRULVHFKDUDFWHULVWLFVDWWKURWWOHVWLFNDFFHOHUDWLRQGHFHOHUDWLRQRSHUDWLRQFDQEHDGMXVWHG$FFHOHUDWLRQIXQFWLRQŏ)XHOPL[WXUHIXQFWLRQ7KLVPL[LQJLVXVHGLQQHHGOHDGMXVWPHQWRIHQJLQHVZKLFKXVHDIXHOPL[WXUHFRQWUROFDUEXUHWRUŏ*RYHUQRUPL[LQJ7KLVPL[LQJLVGHGLFDWHGJRYHUQRUPL[LQJZKHQDJRYHUQRULVXVHG8SWRUDWHVVSHHGVFDQEHVZLWFKHGIRUHDFKFRQGLWLRQ$

$63<Model Basic Setting Procedure>Receiver switchReceiver batteryCharging port/ DSC connector In S.BUSuse(8/SB)S.BUS notusing it (CH1-8)(7/B)ServosƔ$OZD\VFRQQHFWWKHQHFHVVDU\QXPEHURIVHUYRVƔ7KHUHFHLYHUFKDQQHODVVLJQPHQWGHSHQGVRQWKHPRGHOW\SH6HHWKH6HUYRFRQQHFWLRQE\PRGHOW\SHWDEOHV56%RXWSXWFRQQHFWRUVHFWLRQ5HFHLYHUFRQQHFWRUVƔa2XWSXWIRUFRQYHQWLRQDOV\VWHP&+aƔ%2XWSXWIRUFRQYHQWLRQDOV\VWHP&+3RZHUVXSSO\Ɣ6%2XWSXWIRUFRQYHQWLRQDOV\VWHP&+RU6%86SRUWƔ6%866%86SRUWƔ0RQLWRU/('7HOHPHWU\VHQVRUHWF5HFHLYHUDQGVHUYRVFRQQHFWLRQGLDJUDPReceiver and servos connectionConnect the receiver and servos in accordance with the connection diagram shown below. Always read [Precautions when mounting the receiver and servos] of [Before using]. When mounting the receiver and servos to the fuselage, connect the necessary points in accordance with the kit instruction manual.Ɣ7KH6HUYRFRQQHFWLRQE\PRGHOW\SHWDEOHVDUHVKRZQRQWKHIROORZLQJSDJHVConnect the servos to match the fuselage used.$

$64 <Model Basic Setting Procedure>6HUYRFRQQHFWLRQE\PRGHOW\SHThe T18MZ transmitter channels are automatically assigned for optimal combination according to the type selected with the Model Type function of the Linkage Menu. The channel assignment (initial setting) for each model type is shown below. Connect the receiver and servos to match the type used.*The set channels can be checked at the Function screen of the Linkage Menu. The channel assignments can also be changed. For more information, read the description of the Function menu.$LUSODQHJOLGHUPRWRUJOLGHUƔ$LUSODQHDQG9WDLORX CH1AIL 2AIL 2AIL+1FLAP 2AIL+2FLAPAirplane Glider Airplane Glider Airplane Glider Airplane GliderEP EP EP EP12345678910111213141516DG1DG2RX CH2AIL+4FLAP 4AIL+2FLAP 4AIL+4FLAPAirplane Glider Airplane Glider Airplane GliderEP EP EP12345678910111213141516DG1DG2$

65<Model Basic Setting Procedure>RX CH1AIL 2AIL 2AIL+1FLAP 2AIL+2FLAPAirplane Glider Airplane Glider Airplane Glider Airplane GliderEP EP EP EP12345678910111213141516DG1DG2RX CH2AIL+4FLAP 4AIL+2FLAP 4AIL+4FLAPAirplane Glider Airplane Glider Airplane GliderEP EP EP12345678910111213141516DG1DG2Ɣ$LOHYDWRU

66 <Model Basic Setting Procedure>Ɣ7DLOOHVVZLQJRX CH2AIL 2AIL+1FLAP 2AIL+2FLAPAirplane Glider Airplane Glider Airplane GliderEP EP EP12345678910111213141516DG1DG2RX CH2AIL+4FLAP 4AIL+2FLAP 4AIL+4FLAPAirplane Glider Airplane Glider Airplane GliderEP EP EP12345678910111213141516DG1DG2

67<Model Basic Setting Procedure>Ɣ7DLOOHVVZLQJ:LQJOHW5XGGHURX CH2AIL 2AIL+1FLAP 2AIL+2FLAPAirplane Glider Airplane Glider Airplane GliderEP EP EP12345678910111213141516DG1DG2RX CH2AIL+4FLAP 4AIL+2FLAP 4AIL+4FLAPAirplane Glider Airplane Glider Airplane GliderEP EP EP12345678910111213141516DG1DG2

68 <Model Basic Setting Procedure>CHH-4/H-4X SwashAll Other12345678910111213141516DG1DG2CHH-4/H-4X SwashAll Other12345678910111213141516DG1DG2HelicopterƔ)$667HVW&+)$66708/7,)$667&+6)+66Ɣ)$667HVW&+

$69<Linkage Menu>FUNCTIONS OF LINKAGE MENUSystem Menu--Condition HoldLinkage Menu Model Menu Cond.HoldModel 1 Normal 85%Linkage MenuModel Select Model Type PictureSystem Type Function Sub-TrimFail Safe Throttle CutTimerSwash Ring SwashSoundServo MonitorServo ReverseIdle DownINHEnd Point(ATV)1/2The Linkage Menu is made up of functions which perform model addition, model type selection, frequency setting, end point setting, and other model basic settings.ŏ5HWXUQWR+RPHVFUHHQŏ:KHQDEXWWRQLQWKH/LQNDJH0HQXRIWKH+RPHVFUHHQLVWRXFKHGWKHPHQXVKRZQEHORZLVFDOOHG7RXFKWKHEXWWRQRIWKHIXQFWLRQ\RXZDQWWRVHWThe functions which can be selected depend on the model type. A typical menu screen is shown below.Linkage Menu functions table[Servo Monitor]: Displays the servo test and operation position[Model Select]: Model addition, call, deletion, copy, model name setting[Model Type]: Model type, wing type, switch type, etc. selection[Picture]: Picture paste for each model[Sound]: Sound recording and playback[System Type]: System selection, receiver link[Function]: Channel assignment of each function can be changed[Sub-Trim]: Adjusts the neutral position of each servo[Servo Reverse]: Servo direction reversal[Fail Safe]: Fail safe function and battery fail safe function setting[End Point (ATV)]: Servo basic rudder adjustment and limit setting[Throttle Cut]: Stops the engine safely and easily (airplane and helicopter only)[Idle Down]: Lowers the idle speed of the engine (airplane and helicopter only)[Swash Ring]: Limits the decline of the swash plate to prevent linkage damage (helicopter only)[Swash]: Swash AFR and linkage correction function (helicopter only)[Timer]: Timer setting and lap time display[Dial Monitor]: Dial, sliding lever, and digital trim position display[Function Name]: Function Name can be changed[Telemetry]: Displays various data sent from the receiver.[Sensor]: Various telemetry sensors setting[Warning]: Setting of warning sound and vibration[Data Reset]: Model memory set data reset (by item)Condition Hold function ON/OFF button)RUDGHWDLOHGGHVFULSWLRQVHHS&RQGLWLRQ+ROGIXQFWLRQ$

$70 <Linkage Menu>Servo Monitor 6HUYR7HVW*UDSK'LVSOD\'LVSOD\VVHUYRSRVLWLRQVThis is used for testing servo movement. Touch “Moving Test” (repetition mode) or “Neutral Test” (fixed position mode) depending on which one shows on the screen. To get from one to the other, simply touch the field again, and you willŏ5HWXUQWR/LQNDJH0HQXŏ7RXFKWKH>6HUYR0RQLWRU@EXWWRQLQWKH/LQNDJH0HQXWRFDOOWKHVHWXSVFUHHQVKRZQEHORZmove from “Moving Test” to “Neutral Test”automatically. Next touch the “Test” on/off button to start testing your servos. The “Neutral test” is good for finding the neutral position of a servo horn.Servo test operation6HOHFWDWHVWPRGH>0RYLQJ@RU>1HXWUDO@>5HSHDW@(DFKVHUYRUHSHDWVRSHUDWLRQ>1HXWUDO@(DFKVHUYRLVORFNHGLQWKHQHXWUDOSRVLWLRQ:KHQWKH>7HVW2II@EXWWRQLVWRXFKHGWHVWLQJEHJLQVLQWKHVHOHFWHGPRGH&RQWUROQDPH)XQFWLRQQDPH$

$71<Linkage Menu>ŏ5HWXUQWR/LQNDJH0HQXŏ&KHFNPDUNŏ7RXFKWKH>0RGHO6HOHFW@EXWWRQLQWKH/LQNDJH0HQXWRFDOOWKHVHWXSVFUHHQVKRZQEHORZModel Select7KH0RGHO6HOHFWLRQIXQFWLRQSHUIRUPVPRGHODGGLWLRQFDOOGHOHWLRQFRS\DQGPRGHOQDPHVHWWLQJThis function is used to load the settings of the desired model into the T18MZ’s memory.The settings may be selected from either the transmitter’s built-in memory or a SD card/USBmemory.The name of the model stored in the transmitter and the SD card/USB memory may be changed. This can be very useful to tell different models settings apart. Each model name can be as long as 32 characters, and the model name always appears in the display screen.The Copy function is used to copy one set of model data into a second memory within the transmitter and the SD card/USB memory. It may be used for getting a head-start on setting up models with almost the same VHWWLQJVRQO\GLIIHUHQFHVQHHGWREHPRGL¿HGLQVWHDGof entering the complete model from scratch). Also,this function may be used to make a backup copy of a model setup before any changes are made.(The display screen is an example. The screen depends on the model type.)(Model list)Model call7RXFKWKH6DYHWRLFRQDQGVHOHFWWKHORFDWLRQWRZKLFKWKHGHVLUHGPRGHOLVWREHVDYHG7UDQVPLWWHULFRQ7UDQVPLWWHUPHPRU\6'FDUGLFRQ6'FDUG86%PHPRU\LFRQ86%PHPRU\7RXFKWKHGHVLUHGPRGHOLQWKHPRGHOOLVW7RXFKWKH>6HOHFW@EXWWRQ7RXFK><HV@WRFDOOWKHPRGHO:KHQ\RXZDQWWRFDQFHOPRGHOFDOOSUHVV>1R@Model addition7RXFKWKH>1HZ@EXWWRQ7RXFK><HV@WRDGGWKHPRGHO:KHQ\RXZDQWWRFDQFHOPRGHODGGLWLRQWRXFK>1R@*When a new model is added, the Model Type screen areautomatically displayed. Check or change the model. If there are no changes, touch the Model Type icons.*The added model is displayed in the model list.Model deletion7RXFKWKH6DYHWRLFRQRUWKHPRGHO\RXZDQWWRGHOHWHLQWKHPRGHOOLVW7KHPRGHOFXUUHQWO\VHOHFWHGFDQQRWEHGHOHWHG$FKHFNPDUNLVDWWDFKHGWRWKHPRGHO7RXFKWKH>'HOHWH@EXWWRQ7RXFK><HV@:KHQ\RXZDQWWRVWRSPRGHOGHOHWLRQWRXFK>1R@Model name change6HOHFWWKHPRGHOE\WRXFKLQJWKH6DYHWRLFRQRUWKHGHVLUHGPRGHOLQWKHPRGHOOLVW:KHQ>&KDQJH1DPH@LVWRXFKHGDNH\ERDUGDSSHDUVRQWKHVFUHHQ(QWHUWKHPRGHOQDPHIURPWKLVNH\ERDUG*Up to 32 characters can be input at the model name. Japanese language input is also possible.(For a detailed description of the input method, see "User Name Registration/Character Input Method" of the Basic Operation section.Model copy$PRGHOWRFRS\IURPDPRGHOOLVWLVSXVKHG&KHFNPDUNLVDWWDFKHGWRWKHPRGHODQGD&RS\EXWWRQLVGLVSOD\HGRQWKHULJKW7RXFKWKH&RS\EXWWRQDQG7RXFKWKH'HVWLQDWLRQEXWWRQDQGVHOHFWWKHFRS\VWRUDJHGHVWLQDWLRQ7UDQVPLWWHURU6'FDUG86%PHPRU\7RXFKWKHFHQWHU>&RS\@EXWWRQ:KHQ><HV@LVWRXFKHGFRS\LQJLVH[HFXWHG:KHQ\RXZDQWWRFDQFHOFRS\LQJWRXFK>1R@*If there is no model of the same name at the copy destination, the name of the copy source is saved. If there is a model of the same name, a number is appended to the end of the model name and the model is copied. Change the name later.*When the model data was copied, the model date data is reset to the date the model was copied.ŏ6DYHWRŏ$

$72 <Linkage Menu>ŏ5HWXUQWR/LQNDJH0HQXŏ7RXFKWKH>0RGHO7\SH@EXWWRQLQWKH/LQNDJH0HQXWRFDOOWKHVHWXSVFUHHQVKRZQEHORZŏ:KHQGDWDWDNLQJRYHULVSRVVLEOHWKHFRQILUPDWLRQVFUHHQRIGDWDLQLWLDOL]DWLRQLVGLVSOD\HG$SXVKRQ>\HV@ZLOOLQLWLDOL]HGDWD$SXVKRQ>QR@ZLOOVXFFHHGGDWDModel Type7KLVIXQFWLRQVHOHFWVWKHPRGHOW\SHIURPDPRQJDLUSODQHKHOLFRSWHUDQGJOLGHU(The display screen is an example. The screen depends on the model type.)Seven types of main wings and three types of tail wings are available for airplanes. Eight swash types are available for helicopters. Seven types of main wings and three types of tail wingsare available for gliders. Functions and mixing functions necessary for each model type are set in advance at the factory.1RWH7KH0RGHO7\SHIXQFWLRQDXWRPDWLFDOO\VHOHFWVWKHDSSURSULDWHRXWSXWFKDQQHOVFRQWUROIXQFWLRQVDQGPL[LQJIXQFWLRQVIRUWKHFKRVHQPRGHOW\SH:KHQWKH0RGHO 7\SH6HOHFWLRQFRPPDQGLVDFFHVVHGDOORIWKH GDWDLQWKHDFWLYHPHPRU\LVFOHDUHG%HVXUHWKDW\RXGRQ·WPLQGORVLQJWKLVGDWDRUEDFNLWXS WRDQRWKHUPHPRU\XVLQJWKHFRS\LQJIXQFWLRQVModel type selection&DOOWKH7\SHVHOHFWVFUHHQE\WRXFKLQJWKHPRGHOW\SHZLQJWDLOVZDVKW\SHRURWKHUW\SHEXWWRQ6HOHFWWKHW\SH\RXZDQWWRVHWDQGH[HFXWHW\SHVHOHFWLRQE\WRXFKLQJ><HV@DWWKHFRQILUPDWLRQVFUHHQ:KHQ\RXZDQWWRFDQFHOPRGHOW\SHVHOHFWLRQWRXFK>1R@Data taking over after a swash type change 'DWDWDNLQJRYHUPD\EHSRVVLEOHLQWKHVZDVKW\SHRIDKHOLFRSWHUDWWKHWLPHRIDFKDQJH5HIHUWRWKHIROORZLQJWDEOH(YHQZKHQLWVXFFHHGVWKHGDWDRID>VZDVKVHWWLQJ@VFUHHQLVLQLWLDOL]HGBefore After Data taking overH-1, H-2, HE3,HR3, HN3, H-3H-1, H-2, HE3,HR3, HN3, H-3OK++;++;OKH-1, H-2, HE3,HR3, HN3, H-3++;NG++;H-1, H-2, HE3,HR3, HN3, H-3NG$

$73<Linkage Menu>Model 1Please select model type.Airplane Helicopter Glider EP Glider85%ReturnModel TypeModel 1 85%Model Type1 AILERONAIL2 AILERONAIL AIL22 AIL + 1 FLP AIL AIL2FLP2 AIL + 2 FLP AIL AIL2FLP FLP22 AIL + 4 FLP AIL AIL2FLPFLP3FLP4FLP24 AIL + 2 FLP AIL3AILAIL2AIL4FLPFLP24 AIL + 4 FLP AIL3AILAIL2AIL4FLPFLP3FLP4FLP2Please select a wing type.Return1/2Model 1 85%Model TypePlease select a wing type.Return2/2Flying Wing2AIL+4FLPAIL AIL2FLPFLP3 FLP4FLP2Flying Wing4AIL+2FLPAIL AIL2FLPAIL3 AIL4FLP2Flying Wing4AIL+4FLPAIL3AILAIL2AIL4FLPFLP3 FLP4FLP2Flying WingAIL AIL22AILFlying WingAIL AIL2FLP2AIL+1FLPFlying WingAIL AIL2FLP FLP22AIL+2FLPModel 1 85%Model TypePlease select a Rudder type. ReturnNormal RudderRUDWinglet (2RUD)RUD RUD2Model 1 85%Model TypePlease select a tail type. ReturnNORMALELEELERUDAILVATORELE2ELE RUDELERUDV-TAILModel 1 85%Model TypeSwash TypeModel TypeModel 1 85%Model TypePlease select a swash type.ReturnModel typeSelect the model typefrom among airplane, helicopter, glider, and motor glider.ŏ0RGHOW\SHVHOHFWLRQ(Airplane, glider)(Helicopter)ŏ:LQJW\SHVHOHFWLRQŏ:LQJW\SHVHOHFWLRQŏ5XGGHUW\SHVHOHFWLRQŏ6ZDVKW\SHVHOHFWLRQŏ7DLOW\SHVHOHFWLRQWing type (1/2) (Normal)Select from among :DLOHURQDLOHURQVDLOHURQVÀDSDLOHURQVÀDSVDLOHURQVÀDSVDLOHURQVÀDSVDLOHURQVÀDSVWing type (2/2) (Tailless wing)Selection from among: DLOHURQVDLOHURQVÀDSDLOHURQVÀDSVDLOHURQVÀDSVDLOHURQVÀDSVDLOHURQVÀDSV*For tailless wing, the rudder type can be selected from normal rudder and winglet.Tail typeSelect from normal, V tail, and elevator.Helicopter swash type6HOHFWIURPDPRQJ++++(+5+1+DQG+;$

$74 <Linkage Menu>File ListCurrent File File not found !File not found !Model 185%ThumbnailPictureIMG00001Previewŏ7RXFKWKH>3LFWXUH@EXWWRQLQWKH/LQNDJH0HQXWRFDOOWKHVHWXSVFUHHQVKRZQEHORZPicture $SLFWXUHFDQEHSDVWHGIRUHDFKPRGHO6LPSOLILHVLGHQWLILFDWLRQRIWKHPRGHOGDWDGXULQJVFUHHQRSHUDWLRQA photograph of the model taken with a T18MZ camera, digital camera or other file can be pasted as the screen display data for each model. This is convenient in identifying models with the same model name.7KHSLFWXUH¿OHVZKLFKFDQEHGLVSOD\HGRQWKHVFUHHQDUHsize 168 x 80 pixels, file type .bmp (bit map picture)and -3(*¿OHV,ID¿OHODUJHUWKDQWKLVLVSDVWHGWKH,WUHGXFHVof the picture is displayed.When a picture is pasted, it is displayed as the following screen image:ŏ0RGHO6HOHFWVFUHHQŏ+RPHVFUHHQŏ6WDUWXSVFUHHQPasting of picture*Picture data is pasted to the model memory currently in use.*The picture can choose only what is saved in the place (T18MZ, SD card, USB memory) same now as the model data under selection.6HOHFWWKHSLFWXUHIURPWKH7KXPEQDLOE\WRXFKLQJWKHGHVLUHGSLFWXUHGDWD*Before selection, touch the scroll button at the top or bottom of the Thumbnail and confirm the contents of the picture ¿OHVVDYHGDWWKHSUHYLHZVFUHHQ7RSDVWHWKHSLFWXUHWRXFK><HV@:KHQ\RXZDQWWRFDQFHOSDVWLQJWRXFK>1R@[Important]Before reading data from the PC, insert the SD card/USB memory into the transmitter and turn on the power. The following folders areDXWRPDWLFDOO\ZULWWHQ7RUHDGD¿OHIURPWKH3&FRS\WKH¿OHWRDIROGHUE\¿OHW\SHŏ%033LFWXUHÀOHŏ:$9$XGLRÀOHŏ:0$0XVLFÀOHŏ02'(/0RGHOGDWD$

$75<Linkage Menu>85%Sound Model1No Switch ModeStart up3RZHURí23456File Rec 1OFFOFFOFFOFFNo Switch Mode89101112File Rec 7OFFOFFOFFOFFOFFOFF1/285%Model1No Switch ModeStart up01 : test.wav3RZHURí23456File Rec 1OFFOFFOFFOFFEntry CloseRenameDelete<Sound>ŏ5HWXUQWR/LQNDJH0HQXŏ7RXFKWKH>6RXQG@EXWWRQLQWKH/LQNDJH0HQXWRFDOOWKHVHWXSVFUHHQVKRZQEHORZSound 6RXQGUHFRUGLQJDQGSOD\EDFN6DYHGVRXQG¿OH[Important]Before reading data from a PC, insert the SD card/USB memory into the transmitter and turn on the power. The following folders are automatically written. When reading a file from WKH3&FRS\LWWRDKROGHUE\¿OHW\SHŏ%033LFWXUHÀOHŏ:$9$XGLRÀOHŏ:0$0XVLFÀOHŏ02'(/0RGHOGDWDSounds recorded with the microphone built into WKHWUDQVPLWWHUDQGDXGLR¿OHVZDYFDQEHSOD\HGback when the power switch is turned on and off or by preset switch.*Only the voice file saved in the same place (T18MZ, SD card, a USB memory) as the model data under present selection can be chosen.*The recording time from the microphone is up to 3 seconds/UHFRUGLQJ7ZHQW\IRXUDXGLR¿OHVFDQEHVDYHG*The only audio file type which can be recorded is .wav.Only the sounds recorded with the built-in microphone or an DXGLR¿OHVDYHGIURP\RXU3&WRWKHGDWDSDFNFDQEHSOD\HGback.6HWXSVFUHHQV1RWRFDQEHLQGLYLGXDOO\assigned to audio file switches, etc. The playback ¿OHVFDQEHVZLWFKHGHDFKWLPHWKHVDPHVZLWFKLVoperated. This can be used when playing back thename of maneuvers, etc.>6RXQGVWDUWLQJ@1R:KHQWUDQVPLWWHUSRZHUVZLWFKWXUQHGRQ1R:KHQWUDQVPLWWHUSRZHUVZLWFKWXUQHGRII1Ra6ZLWFKFDQEHVHWVoice Recording7RXFKDQ\5(&EXWWRQWRFDOOXSWKH6281'5(&25'(5VFUHHQ7RXFKWKH5(&EXWWRQWRVWDUWUHFRUGLQJ5HFRUGLQJWLPHVHFRQGV5HFRUG\RXUYRLFHDV\RXDUHIDFLQJWKHWUDQVPLWWHU·VPLFURSKRQH*Please record to a loud sound.7RILQLVKSUHVV´&/26(µ$OVRVRXQGILOHVFUHDWHGE\\RXU3&PD\EHSOD\HGEDFNE\DVVLJQHGVZLWFKHV)LOHW\SHVZDYÀOHRQO\*A voice file is saved automatically in the same place (amain part, SD card, a USB memory) as the model data XQGHUSUHVHQWVHOHFWLRQDQGD¿OHQDPHLVGLVSOD\HGRQWKH¿OHEXWWRQFRUUHVSRQGLQJWRDUHFRUGLQJEXWWRQ$

$76 <Linkage Menu>85%Sound Model1No Switch ModeStart up3RZHURí23456File Rec 1No Switch Mode89101112File Rec 71/2SG$VVLJQPHQWRIDXGLR¿OHVWRVZLWFKHV$XGLR¿OHVFDQEHVDYHGWR6'FDUGEHIRUHKDQG7RXFKWKHÀOHEXWWRQRIWKH1R\RXZDQWWRVHW$OLVWRIWKHÀOHVVWRUHGRQWKH6'FDUGLVGLVSOD\HG6HOHFWWKHDXGLRÀOH\RXZDQWWRSOD\EDFNIURPWKHOLVWRIDXGLRÀOHV*Since the audio files are played back when the audio file names in the list are touched, the file contents can be checked before assignment.7RXFKWKH>)LOH@EXWWRQWRDVVLJQWKHÀOHV6ZLWFKHVDUHDOVRVHOHFWHGIRU1Ra7RXFKWKH>18//@EXWWRQWRFDOOWKH6ZLWFKVHOHFWVFUHHQ6HTXHQWLDOO\SOD\LQJEDFNUHJLVWHUHG¿OHHDFKtime operated by 1 switchThis is used when calling the order of maneuvers, etc.>6HWWLQJPHWKRG@$IWHUVHOHFWLQJWKHVZLWFKSUHVVWKH>ń@EXWWRQ7KHEXWWRQGLVSOD\WKHUHDIWHULVVZLWFKHGDVVKRZQLQWKHVFUHHQDERYH$VVLJQWKHDXGLRÀOHVLQWKHRUGHULQZKLFK\RXZDQWWRSOD\WKHPEDFN7KHDXGLR¿OHVDUHSOD\HGEDFNHDFKWLPHWKHswitch selected by the above setting is turned on.6HOHFWWKHVZLWFKDQGLWV21GLUHFWLRQDWWKH6ZLWFKVHOHFWVFUHHQ)RUDGHWDLOHGGHVFULSWLRQRIWKHVHOHFWLRQPHWKRGVHH6ZLWFKVHWWLQJPHWKRGDWWKHEDFNRIWKLVPDQXDOMode button3OD\LQJEDFNUHJLVWHUHGILOHRQO\RQFH3OD\LQJEDFNUHJLVWHUHGILOHUHSHDWHGO\6HTXHQWLDOO\SOD\LQJEDFNUHJLVWHUHGILOHHDFKWLPHRSHUDWHGE\VZLWFKoí$

$77<Linkage Menu>System mode selection7KH70=LVIRU*+]RQO\7KHV\VWHPFDQbe selected from among the 5 systems FASSTest 18CH, FASSTest 12CH, FASST MULT, FASST 7CH, S-FHSS. Select the system matched to the type of receiver used.Receiver linkingThe receiver can be controlled without being affected by other transmitters by linking it with the transmitter used. When using a receiver other than that of the purchased set, linking is necessary.Dual receiver function (only FASSTest 18CH mode)Two sets of receivers, and a function which can be linked. Two sets of receivers are recognized individually. For example, in R7008SB, CH output setting function is used, by setting one set as "1-8CH", and setting one more set as "9-16CH", two sets of receivers can be carried in one set of the model, and 1-16CH can be used now. If a Dual receiver function is used, the following function can set up individually.䊶Battery fail-safe voltage setup 䊶Telemetry function ON/OFF䊶Sensor setupTelemetry function (FASSTest mode only)To use the telemetry function, set “Telemetry” to “ON”.D/L Interval (FASSTest mode only)When a telemetry function is enabled, the receiving interval (down-link interval) of sensor data can be changed.ŏ5HWXUQWR/LQNDJH0HQXŏ7RXFKWKH>6\VWHP7\SH@EXWWRQLQWKH/LQNDJH0HQXWRFDOOWKHVHWXSVFUHHQVKRZQEHORZSystem Type6\VWHPPRGHVHWWLQJ5HFHLYHUOLQNIf a D/L interval is enlarged, although renewal of a sensor data display becomes slow, a stick response will improve.Battery fail-safe voltage setup (only FASSTest mode)The voltage which battery fail-safe commits at the WLPHRIDOLQNFDQEHVHWXS9$UHFHLYHUmemorizes at the time of a link.Linking method%ULQJWKHUHFHLYHUWREHOLQNHGWRZLWKLQFPRIWKHWUDQVPLWWHU3UHVVWKH>/LQN@EXWWRQLQWKH>/LQN@ER[RI>6\VWHP7\SH@7KHWUDQVPLWWHUHPLWVDFKLPHVRXQGDQGHQWHUVWKHOLQNPRGH7KHUHFHLYHUSRZHULVLPPHGLDWHO\WXUQHGRQ$ERXWVHFRQGVDIWHUWKHSRZHULVWXUQHGRQWKHUHFHLYHUHQWHUVWKHOLQNZDLWVWDWH5HFHLYHUOLQNZDLWLVDERXWVHFRQG,IOLQNLQJLVVXFFHVVIXOWKHUHFHLYHU/('FKDQJHVIURPUHGWRJUHHQWKHOLQNPRGHHQGVDQGWKHUHFHLYHU,'FRGHLVGLVSOD\HG,IOLQNLQJIDLOVDQHUURUPHVVDJHLVGLVSOD\HG%ULQJWKHWUDQVPLWWHUFORVHUWRWKHUHFHLYHUDQGUHSHDWWKHSURFHGXUHDERYHIURP6WHS*Do not perform the linking operation when the drive motor is connected and the engine was started.* When you use two sets of receivers, please be sure to use it, after performing a setup a "primary" and "secondary" in the "dual" mode. *Since two sets of receivers cannot be individuallyrecognized when the setup a "primary" and "secondary" is not carried out, it becomes impossible to receive telemetry data correctly, and makes it. * The link of two sets of receivers should perform one link operation at a time. If two power supplies of a receiver are switched on simultaneously, it is correctly unreceivable by the transmitter side.* If a dual receiver function is used, in order to receive sensor information by turns from two sets of receivers,renewal of telemetry data becomes slow rather than a single receiver's case.* It cannot link with three sets of receivers.$

78 <Linkage Menu>-Response speed has priority over number of channels-Telemetry requires only the remaining receiver battery-Want to use a previously used receiver as is-Want to use a miniature receiver for indoor planes-Want to use an S-FHSS system miniature receiverFASSTest 18CHFASSTest 12CHFASST MULT FASST 7CH S-FHSSR608FSR6008HSR6108SBR6208SBR6014HSR6014FSR6203SBR6203SBER6202SBWR7008SBR617FSR6004FFR616FFMR6106HFR6106HFCR6203SBR6203SBER6202SBWR2006GSR2106GFR2008SBR7008SB(Usable receivers)-Want to use more channels-Want to use a large number of telemetry functions(The time of December, 2011) WARNINGDo not perform the linking operation when thedrive motor is connected and the engine wasstarted.䂓Inadvertent rotation of the motor or acceleration of the engineis extremely dangerous. If link operation is completed, please check that a receiver is returned on and it can once be operated with the linked transmitter.Check operation sufficiently before flying after linking.䂓If the same receiver is sending in the vicinity, there is the danger that the transmitter may be linked with that receiver.CAUTIONSAlways turn on the transmitter power after linkingis complete.When pairing with the transmitter, be sure that a previously linked transmitter is not transmittingSystem Type䂓FASSTest 18CH ---䂓FASSTest 12CH ---䂓FASST MULT ---䂓FASST 7CH --- FASST-7CH system receiver mode. Up to 7 channels can be used.䂓S-FHSS --- S-FHSS system receiver mode. Up to 8 channels can be used.FASSTest system receiver mode. Applicable with the telemetry sensor unit. Up to18 channels (linear 16+ON/OFF2) can be used.FASSTest system receiver mode. Applicable with receiver voltage display. Up to 12channels (linear10+ON/OFF2) can be used. Telemetry Sensorcannot be used, butthe response speed is a faster than that of the 18CH mode.FASST-MULT system receiver mode. Up to 18 channels (linear 16+ON/OFF2) canbe used.

$79<Linkage Menu>ŏ5HWXUQWR/LQNDJH0HQXŏWR>6:$3@ŏ7RXFKWKH>)XQFWLRQ@EXWWRQLQWKH/LQNDJH0HQXWRFDOOWKHVHWXSVFUHHQVKRZQEHORZFunction &KDQQHODVVLJQPHQWRIHDFKIXQFWLRQFDQEHFKDQJHGWhen you select model and wing (swash) types, you will find that the optimized combinations of servo output channels and functions have been already preset. If you would like, on the function-setting screen of the linkage menu, you can freely change combinations of servo output channels,functions (aileron, elevator, etc), and input controllers (sticks, switches, trim levers and trim switches). You can also assign the same function to multiple servo output channels such as assigning elevator function to CH2 and CH3.(The display screen is an example. The screen depends on the model type.)Function change7RXFKWKHIXQFWLRQEXWWRQRIWKHFKDQQHO\RXZDQWWRFKDQJHWRFDOOWKHIXQFWLRQOLVW6HOHFWWKHIXQFWLRQ\RXZDQWWRFKDQJH7RXFK><HV@7KHGLVSOD\UHWXUQVWRWKHRULJLQDOVFUHHQ:KHQ\RXZDQWWRFDQFHOIXQFWLRQFKDQJHWRXFK>1R@*Multiple channels can be assigned to 1 function.DG1, DG2 (switch channels)These two channels can be used as switch channels. You can freely change combinationsbetween servo output channels and input controllers(sticks, switches, trim levers and trim switches).Operation control change7RXFKWKHFRQWUROEXWWRQRIWKHFKDQQHO\RXZDQWWRFKDQJH$&RQWUROVHOHFWVFUHHQVWLFNVZLWFKNQREWULPOHYHUHWFLVGLVSOD\HG6HOHFWWKHFRQWURO\RXZDQWWRRSHUDWH7RXFK>&ORVH@7KHGLVSOD\UHWXUQVWRWKHSUHFHGLQJVFUHHQ*The same control can be assigned to multiple channels.$

$80 <Linkage Menu>(The display screen is an example. The screen depends on the model type.)Trim change7RXFKWKH7ULPEXWWRQWRFDOOWKH7ULPVHWXSVFUHHQ7KHIROORZLQJLWHPVFDQEHVHWDWWKH7ULPVHWXSVFUHHQŏ+DUGZDUHVHWWLQJ6HOHFWLRQRIVZLWFKHWFZKLFKFRQWUROVWULP7KHVHOHFWVFUHHQLVFDOOHGE\WRXFKLQJWKH>+:6HOHFW@EXWWRQŏ5DWHVHWWLQJŏ2SHUDWLRQVWHSVHWWLQJŏ7ULPPRGHVHWWLQJ1RUPDOPRGH1RUPDOWULPSDUDOOHOVKLIWWULPRSHUDWLRQSWAPIf [SWAP] is pushed, it can become the following screen and can replace two functions with the data set as each channel.7RXFKWKH7ULPEXWWRQWZRFKDQQHOVWRFKDQJHLVSXVKHG,I>2.@LVSXVKHGWZRFKDQQHOVZLOOLQWHUFKDQJH,WFDQFKRRVHRQO\WRWZR$7/PRGH$7/RSHUDWLRQPRGH5HYHUVHLVDOVRSRVVLEOH&750PRGH0D[LPXPFKDQJHQHDUFHQWHUE\FHQWHUWULPRSHUDWLRQŏ6HSDUDWHFRPELQDWLRQPRGH7ULPGDWDDUHVHWWRÁLJKWFRQGLWLRQV6HSDUDWHPRGH7ULPDGMXVWPHQWIRUHDFKÁLJKWFRQGLWLRQ$

$81<Linkage Menu>Model1Sub-TrimCH2RUD+0CH1ELE+0CH4AIL+0CH3THR+0CH6ABK+0CH5GEA+0CH8AUX5+0CH7AUX6+0CH10AUX3+0CH9AUX4+0CH12AUX1+0CH11AUX2+0CH14AUX1+0CH13AUX1+0CH16AUX1+0CH15AUX1+085%ŏ5HWXUQWR/LQNDJH0HQXŏ7RXFKWKH>6XE7ULP@EXWWRQLQWKH/LQNDJH0HQXWRFDOOWKHVHWXSVFUHHQVKRZQEHORZSub-Trim6HWWLQJRIQHXWUDOSRVLWLRQRIHDFKVHUYR(The display screen is an example. The screen depends on the model type.)The Sub-Trim function is used to set the servo neutral position, and may be used to make fine adjustments to the control surface after linkagesand pushrods are hooked up. When you begin to set up a model, be sure that the digital trims are set to their center position.Sub trim adjustment7RXFKWKHWULPGLVSOD\SDUWRIWKHFKDQQHO\RXZDQWWRDGMXVW$GMXVWPHQWEXWWRQVDSSHDUVRQWKH6XE7ULPPHQXVFUHHQ8VHWKHDGMXVWPHQWEXWWRQVWRDGMXVWWKHVXEWULPŏ,QLWLDOYDOXHŏ$GMXVWPHQWUDQJHaVWHSV*See above5HSHDWWKLVVWHSIRUHDFKFKDQQHO$

$82 <Linkage Menu>ŏ5HWXUQWR/LQNDJH0HQXŏ7RXFKWKH>6HUYR5HYHUVH@EXWWRQLQWKH/LQNDJH0HQXWRFDOOWKHVHWXSVFUHHQVKRZQEHORZServo Reverse8VHWRUHYHUVHWKHWKURZGLUHFWLRQ(The display screen is an example. The screen depends on the model type.)Servo Reverse changes the direction of an individual servo’s response to a control stick movement.For CCPM helicopters, be sure to read thesection on Swash AFR before reversing any servos. With CCPM helicopters, always complete your servo reversing prior to any other programming. If you use pre-built Airplane/Sailplane functions that control multiple servos, it may be confusing to tell whether the servo needs to be reversed or a setting in the function needs to be reversed. See the instructions for each specialized function for further details. Always check servo direction prior to every Servo reversing procedureAfter setting up a new model, be sure todefine all special menus. Be sure that all servos are plugged into the proper receiver channels. Now, determine whether you need to reverse any channels by moving each stick and observing the corresponding movement in the model’s controls. 7RXFKWKHGHVLUHGFKDQQHO·V6HWWLQJEXWWRQWRFKRRVHWKHSURSHUGLUHFWLRQIRUWKHVHUYR7RXFK´<HVµLQWKHQH[WVFUHHQ5HSHDWIRUHDFKVHUYRQHHGLQJUHYHUVDO:KHQGRQHWRXFK´6HUYR5HYHUVHµWRUHWXUQWRWKH/LQNDJH0HQXÀLJKWDVDQDGGLWLRQDOSUHFDXWLRQWRFRQ¿UPSURSHUmodel memory, hook ups, and radio function.WARNING BHIRUHDÀLJKWLWDOZD\VFHUWDLQO\FKHFNVWKDWDselection model, servo operation, the direction ofservo operation, and a switch setup are right.Initial setting of a motorchannel is reverse.$

$83<Linkage Menu>Fail Safe Model1 Batt. F/SReleaseCH Function Function234561GearAir BrakeThrottleAileronElevatorRudder 891011127Auxiliary6Auxiliary5Auxiliary4Auxiliary3Auxiliary2Auxiliary185%ModeHoldOFFOFFB.F/S F/S Posi. CHOFFOFFOFFHold OFFHold OFFHold OFFHold OFFHold OFFModeHoldOFFOFFB.F/S F/S Posi. OFFOFF CH13-OFFOFFHold OFFHold OFFHold OFFHold OFFHold OFFŏ5HWXUQWR/LQNDJH0HQXŏ7RXFKWKH>)DLO6DIH@EXWWRQLQWKH/LQNDJH0HQXWRFDOOWKHVHWXSVFUHHQVKRZQEHORZFail Safe 6HWVWKHVHUYRVRSHUDWLQJSRVLWLRQZKHQWUDQVPLWWHUVLJQDOVFDQQRORQJHUEHUHFHLYHGRUZKHQWKHUHFHLYHUEDWWHU\YROWDJHGURSV(The display screen is an example. The screen depends on the model type.)The Failsafe function may be used to set up positions that the servos move to in the case of radio interference.When the receiver battery voltage drops, the servocan be moved to a preset position. (Battery fail safe function) A battery fail safe function reset switch can be set. (Initial setting: Throttle stick maximum slow side)You may set either of two positions for each channel: Hold, where the servo maintains its last commanded position, or Failsafe, where each servo moves to a predetermined position. You may chooseeither mode for each channel.The T18MZ system also provides you with an advanced battery monitoring function that warns you when the receiver battery has only a little power remaining. In this case, each servo is PRYHGWRWKHGH¿QHGIDLOVDIHSRVLWLRQ7KHEDWWHU\IDLOVDIHPD\EHUHOHDVHGE\RSHUDWLQJDSUHGH¿QHGcontrol on the transmitter (default is throttle), Fail safe setting procedureDecide which channels you want to go to preset positions, and which ones you want to maintain their last commanded position. To select the failsafe mode you wish to set, use the F/S button. This button toggles between the two modes. (Hold, F/S)F/S mode setting:7RXFKWKH)6EXWWRQRIWKHFKDQQHO\RXZDQWWRVHWDQGVHWWKDWFKDQQHOWRWKH>)6@PRGH+ROGWKHFRUUHVSRQGLQJVWLFNFRQWUROVOLGHURURWKHUFRQWUROLQWKHSRVLWLRQ\RXZDQWWKHVHUYRWRPRYHWRZKHQWKHIDLOVDIHIXQFWLRQLVDFWLYDWHGDQGWRXFKWKH)6SRVLWLRQEXWWRQ7KDWSRVLWLRQLVGLVSOD\HGLQSHUFHQWDJH*When you want to return that channel to the Hold mode,touch the [F/S] button again.Battery fail safe setting procedureTo select the B.F/S mode, touch the [B.F/S] button. Each time the button is touched, it toggles do not continue to fly, land as soon as possible.Remember, if the predefined control suddenly moves to a position you did not command, land at once and check your receiver battery.'H¿QHVVHUYRSRVLWLRQZKHQVLJQDOVDUHORVWDQGwhen receiver battery voltage becomes low.WARNINGFor safety, always set the fail safe functions.Ɣ(VSHFLDOO\VHWWKHWKURWWOHFKDQQHOIDLOVDIHIXQFWLRQVRWKDWthe servo moves to the maximum slow side for airplanes and to the slow side from the hovering position for helicopters. Crashing of the model at full high when normal radio waves cannot be received due to interference, etc., is very dangerous.Ɣ,IIDLOVDIHLVUHVHWE\WKURWWOHVWLFNLWPD\EHPLVWDNHQIRUDQengine malfunction and will be reset at throttle slow and the model ZLOOFRQWLQXHWRÀ\,I\RXKDYHDQ\GRXEWVLPPHGLDWHO\ODQGbetween [OFF] and [B.F/S].B.F/S setting:7RXFKWKH>%)6@EXWWRQRIWKHGHVLUHGFKDQQHOWRVHWLWWRWKH%)6PRGH+ROGWKHFRUUHVSRQGLQJVWLFN95VOLGHURURWKHUFRQWUROLQWKHSRVLWLRQ\RXZDQWWKHVHUYRWRPRYHWRZKHQWKHEDWWHU\IDLOVDIHIXQFWLRQLVDFWLYDWHGDQGWRXFKWKH)6SRVLWLRQEXWWRQ7KLVSRVLWLRQLVGLVSOD\HGLQSHUFHQWDJH*When you want to return that channel to OFF, touch the [B.F/S] button again.Battery Failsafe Release FunctionThis function releases the predefined controlfrom it's held position after indicating that your receiver battery is low. (QWHUWKHFRQWUROVHWWLQJVFUHHQE\WRXFKLQJWKH%DWWHU\)65HOHDVHEXWWRQ1RZ\RXPD\FKRRVHWKDWPRYLQJWKHWKURWWOHUHVHWVWKHFRQGLWLRQRUVHOHFWDQRWKHUVWLFNRUVZLWFKGHDFWLYDWHVLW7RVHWDGHVLUHGWKURWWOHUHOHDVHSRVLWLRQPRYHWKHWKURWWOHVWLFNWRWKHSRLQWDWZKLFK\RXZLVKWKH%)6WREHUHOHDVHGŏ7R6ZLWFK!VFUHHQ$

$84 <Linkage Menu>End Point(ATV) Model1CH Function234561GearAir BrakeThrottleAileronElevatorRudder85%Limit135%OFFOFF135%135%135%135%135%Limit135%OFFOFF135%135%135%135%135%Speed0OFFOFF00000Tra vel100%OFFOFF100%100%100%100%100%Tra vel100%OFFOFF100%100%100%100%100%CH7-12ŏ7RXFKWKH>(QG3RLQW$79@EXWWRQLQWKH/LQNDJH0HQXWRFDOOWKHVHWXSVFUHHQVKRZQEHORZEnd Point (ATV)6HWVWKHWUDYHOOLPLWSRLQWDQGVSHHGRIHDFKVHUYR(The display screen is an example. The screen depends on the model type.)The End Point function adjusts the left and right servo throws, generates differential throws, and will correct improper linkage settings. 7KH7UDYHOUDWHFDQEHYDULHGIURPWRin each direction on channels 1 to 16. Also, the Limit point where servo throw stops may be varied from 0% to 155%.Servo travel adjustment7RXFKWKH7UDYHOEXWWRQRIWKHFKDQQHO\RXZDQWWRVHW$GMXVWPHQWEXWWRQVDSSHDURQWKHVFUHHQ8VHWKHVHEXWWRQVWRDGMXVWWKHUDWHŏ,QLWLDOYDOXHŏ$GMXVWPHQWUDQJHa5HSHDWWKHSURFHGXUHDERYHIRUHDFKUDWHLimit point adjustment7RXFKWKH/LPLWEXWWRQRIWKHFKDQQHO\RXZDQWWRVHW8VHWKHDGMXVWPHQWEXWWRQVWRDGMXVWWKHOLPLWSRLQWŏ,QLWLDOYDOXHŏ$GMXVWPHQWUDQJHa5HSHDWWKLVSURFHGXUHIRUHDFKOLPLWSRLQWNOTE: The indicators on the screen display actual servo throw of the each channel. The center position of the indicator is based on the Sub-Trim settings. Therefore the Sub-Trim adjustment changes the Limit point display of the indicator. The Servo Speed setting is used to set the servo delay for each channel, from channel l to channel 16. The system uses the programmed speed (delay) to slow down servo position changes. The Servo Speed setting can bevaried from 0 to 27 in each channel.Servo speed setting7RXFKWKH6SHHGEXWWRQRIWKHFKDQQHO\RXZDQWWRVHW8VHWKHDGMXVWPHQWEXWWRQVWRDGMXVWWKHVHUYRVSHHGŏ,QLWLDOYDOXHŏ$GMXVWPHQWUDQJHaVWHSV5HSHDWWKLVSURFHGXUHIRUHDFKFKDQQHO7RFORVHWKLVVFUHHQWRXFKWKH>(QG3RLQW$79@EXWWRQ$

$85<Linkage Menu>ŏ5HWXUQWR/LQNDJH0HQXŏ7RXFKWKH>7KURWWOH&XW@EXWWRQLQWKH/LQNDJH0HQXWRFDOOWKHVHWXSVFUHHQVKRZQEHORZThrottle Cut 6WRSVWKHHQJLQHVDIHO\DQGHDVLO\DLUSODQHDQGKHOLFRSWHURQO\(The display screen is an example. The screen depends on the model type.)Throttle cut provides an easy way to stop the HQJLQHE\ÀLSSLQJDVZLWFKZLWKWKHWKURWWOHVWLFNat idle. The action is not functional at high throttle to avoid accidental dead sticks. The switch’s location and direction must be chosen, as it defaults to NULL.Throttle cut setting procedure&RQGLWLRQWRVHWXSWRXFKWKH,1+EXWWRQWRDFWLYDWHWKH7KURWWOH&XWIXQFWLRQ7KURWWOHFXWIXQFWLRQVZLWFKVHWWLQJ7RXFKWKH18//EXWWRQWRFDOOWKH6ZLWFK!VFUHHQDQGWKHQVHOHFWWKHVZLWFKDQGLWV21GLUHFWLRQ)RUDGHWDLOHGGHVFULSWLRQRIWKHVHOHFWLRQPHWKRGVHH>6ZLWFK6HWWLQJ0HWKRG@DWWKHEDFNRIWKLVPDQXDO7KURWWOHFXWSRVLWLRQVHWWLQJ6HWWKHWKURWWOHVWLFNWRPD[LPXPVORZDQGWRXFKWKH&XW3RVLWLRQEXWWRQ$GMXVWPHQWEXWWRQVDSSHDU$WWKHVDPHWLPHWKHQXPHULFDOYDOXHRIWKHFXUUHQWPD[LPXPVORZVLGHLVGLVSOD\HGDW&XW3RVLWLRQ8VHWKHDGMXVWPHQWEXWWRQVWRDGMXVWWKHVHUYRWUDYHOZKHQWKHWKURWWOHFXWIXQFWLRQLVDFWLYDWHGŏ,QLWLDOYDOXHŏ$GMXVWPHQWUDQJHa*With throttle stick at idle, adjust the rate until the engine consistently shuts off, but throttle linkage is not binding. :KHQ¿QLVKHGWRXFKWKH³7KURWWOH&XW´EXWWRQWRH[LW7RH[LWWKHVHWWLQJWRXFKWKH>7KURWWOH&XW@EXWWRQNOTE: When condition is set up, a setup of ON/OFF can be performed for every condition. Only as for the condition to which the throttle cut is an operating state (ON/OFF) from INH, a throttle cut can turn ON. While the throttle cut hasbeen ON, when a throttle cut changes to the condition of INH, a cut is canceled by the throttle cut switch OFF with ON, and the throttle cut cannot turn ON in the condition.$

$86 <Linkage Menu>85%Model 1Throttle CHOFFSwitchACT/INH2íVHW HLINH+0%Idle Downŏ5HWXUQWR/LQNDJH0HQXŏ7RXFKWKH>,GOH'RZQ@EXWWRQLQWKH/LQNDJH0HQXWRFDOOWKHVHWXSVFUHHQVKRZQEHORZIdle Down /RZHUVWKHHQJLQHLGOLQJVSHHGDLUSODQHDQGKHOLFRSWHURQO\(The display screen is an example. The screen depends on the model type.)The Idle Down function lowers the engines idle E\ÀLSSLQJDVZLWFKZLWKWKHWKURWWOHVWLFNDWLGOHThe action is not functional at high throttle to avoid accidental dead sticks. The switch’s location and direction must be chosen, as it defaults to NULL.Idle down setting procedure7RXFKWKH,1+EXWWRQWRDFWLYDWHWKH,GOH'RZQIXQFWLRQ,GOH'RZQIXQFWLRQVZLWFKVHWWLQJ7RXFKWKH18//EXWWRQWRFDOOWKH6ZLWFK!VFUHHQDQGWKHQVHOHFWWKHVZLWFKDQGLWV21GLUHFWLRQ)RUDGHWDLOHGGHVFULSWLRQRIWKHVHOHFWLRQPHWKRGVHH>6ZLWFK6HWWLQJ0HWKRG@DWWKHEDFNRIWKLVPDQXDO2IIVHWUDWHVHWWLQJ7RXFKWKH2IIVHW5DWHEXWWRQ$GMXVWPHQWEXWWRQVDSSHDURQWKHVFUHHQ8VHWKHVHEXWWRQVWRDGMXVWWKHRIIVHWUDWHŏ,QLWLDOYDOXHŏ$GMXVWPHQWUDQJHaEHFRPHVDQLGOHXS7RH[LWWKHVHWWLQJWRXFKWKH>,GOH'RZQ@EXWWRQ$

$87<Linkage Menu>85%Model 1Elevator +0%Swash RingONAileronRate+0%100%Resetŏ5HWXUQWR/LQNDJH0HQXŏ7RXFKWKH>6ZDVKULQJ@EXWWRQLQWKH/LQNDJH0HQXWRFDOOWKHVHWXSVFUHHQVKRZQEHORZSwash Ring /LPLWVWKHGHFOLQHRIWKHVZDVKSODWHWRSUHYHQWOLQNDJHGDPDJH+HOLFRSWHURQO\This function limits the decline of the swash plate to prevent linkage damage as the aileron and elevator operation is added. It is useful for 3D heli setting.Swash ring setting procedure3XVKWKH6ZDVKULQJEXWWRQRQWKHOLQNDJHPHQX3XVK$&7,1+EXWWRQWRDFWLYDWH*The movement area monitor shows the current aileron and elevator values and limit ranges by the yellow circle.$GMXVWWKHUDWHWRWKHPD[LPXPDPRXQWRIVZDVKSODWHGHFOLQH*The swash movement is limited within the circle. $GMXVWPHQWUDQJH5DWHEXWWRQ$FWLYDWHEXWWRQ$

$88 <Linkage Menu>85%Model 1Mixing RateSwash Detail Swash(AFR)PIT to ELEAIL to PITELE to AILELE to PIT100% 100%100% 100%100% 100%50% 50%50% 50%PIT to AILMixingLinkage CompensationFunction Dir.AileronElevatorSpeed Compensation0% 0%0% 0%0%Low Pitch++ŏ5HWXUQWR/LQNDJH0HQXŏ7R6ZDVK$)5VFUHHQ85%Model 1Neutral Point Swash AFRAileronElevatorH100%50% 50%0% LLow Pitch+50%Enter PitchSwash Swash DetailHigh Pitch+50%+50%ŏ5HWXUQWR/LQNDJH0HQXŏ7RXFKWKH>6ZDVK@EXWWRQLQWKH/LQNDJH0HQXWRFDOOWKHVHWXSVFUHHQVKRZQEHORZSwash6ZDVKRSHUDWLRQOLQNDJHFRUUHFWLRQIXQFWLRQ7KLVVZDVKVHWXSVFUHHQGRHVQRWDSSHDUIRUVZDVKW\SH+Neutral PointAt your linkages, if the servo horn deviates from the perpendicular position at neutral, the linkagecompensation functions may not compensateeffectively. This neutral point setting reads the linkage compensation neutral position. However, this adjustment only changes the datum point of the compensation function on the swash details screen and does not affect the neutral position of other functions.*Before using the compensation function, set the neutralpoint.Swash AFRThe swash AFR function adjusts (increases/decreases/reverse) the rate (travel) of the aileron, elevator, and pitch functions.Mixing Rate(Normally, the initial value is used.)This mixing rate is used for correction so that the swash plate moves in the correct direction for aileron, elevator, and pitch operation. Compensation mixing is shown below.*PIT->AIL/PIT->ELE/AIL->PIT/ELE->AIL/ELE->PIT*Use the corresponding compensation mixing and compensate so that the swash plate moves in the correct direction.Linkage CompensationThis compensation mixing is used to correct for mutual interference when the ailerons or elevators were operated when the throttle stick was in the slow or high position.Speed CompensationThis speed compensation function compensatesthe mutual interference when the travel of each servo is different at swash plate operation. For HR-3, it compensates the speed by dropping the operating speed of the aileron and pitch servos at elevator operation.ŏ7R6ZDVK'HWDLOVVFUHHQ$

$89<Linkage Menu>Neutral point setting procedure*Becomes the compensation datum point.*Adjusting the servo horn so that the neutral point position is near the 50% position makes the mixing amount small.+ROGWKHVHUYRKRUQDWDULJKWDQJOHWRWKHOLQNDJHURGDQGWKHQWRXFKWKH>(QWHU@EXWWRQDQGUHDGWKHDFWXDOQHXWUDOSRLQW*The neutral point is displayed on the screen. $IWHUUHDGLQJWKLVQHXWUDOSRLQWXVHRWKHUFRPSHQVDWLRQIXQFWLRQVWRPDNHIXUWKHUDGMXVWPHQWV 7RH[LWWKHVHWWLQJWRXFKWKH>6ZDVK@EXWWRQSwash AFR setting procedure $GMXVWVRWKDWWKHVSHFLILHGRSHUDWLRQDPRXQWLVREWDLQHGE\DLOHURQHOHYDWRUDQGSLWFKRSHUDWLRQ7RXFKWKHEXWWRQRIWKH$)5UDWHWREHDGMXVWHG$GMXVWPHQWEXWWRQVDSSHDURQWKHVFUHHQ8VHWKHDGMXVWPHQWEXWWRQVWRDGMXVWWKH$)5UDWH ,QLWLDOYDOXH $GMXVWPHQWUDQJHa 7RH[LWVHWWLQJWRXFKWKH>6ZDVK@EXWWRQMixing rate setting procedure+5LVGHVFULEHGDVDQH[DPSOH7KHPL[LQJDSSOLHGLQRWKHUVZDVKPRGHVLVGLIIHUHQWEXWWKHVHWWLQJSURFHGXUHLVWKHVDPH6HWWKHWKURWWOHVWLFNWRWKHVHWQHXWUDOSRLQW$GMXVWWKHOHQJWKRIWKHOLQNDJHURGVRWKDWWKHVZDVKSODWHLVKRUL]RQWDODWWKLVSRVLWLRQ $OLWWOHDGMXVWPHQWXVLQJVXEWULPVKRXOGEH2.$GMXVWVRWKDWSLWFKRSHUDWLRQZKHQWKHSLWFKFXUYHLVVWUDLJKWLVPD[LPXP$GMXVWWKH$,/!3,7DPRXQWVRWKHUHLVQRLQWHUIHUHQFHLQWKHHOHYDWRURUSLWFKGLUHFWLRQZKHQWKHDLOHURQVWLFNLVPRYHGWRWKHOHIWDQGULJKW$GMXVWWKHOHIWDQGULJKWVLGHVVHSDUDWHO\$GMXVWWKH(/(!$,/DQG(/(!3,7DPRXQWVVRWKHUHLVQRWLQWHUIHUHQFHLQWKHDLOHURQRUSLWFKGLUHFWLRQZKHQWKHHOHYDWRUVWLFNLVPRYHGXSDQGGRZQ$GMXVWWKHXSDQGGRZQVLGHVVHSDUDWHO\$GMXVWWKH3,7!$,/DQG3,7!(/(DPRXQWVVRWKDWWKHVZDVKSODWHLVKRUL]RQWDOZKHQWKHWKURWWOHVWLFNLVVHWWRPD[LPXPVORZDQGIXOOKLJK$GMXVWWKHVORZDQGKLJKVLGHVVHSDUDWHO\7RH[LWVHWWLQJWRXFKWKH>6ZDVK'HWDLOV@EXWWRQLinkage correction setting procedure6HWWKHOLQNDJHFRPSHQVDWLRQDIWHUVHWWLQJWKHPL[LQJUDWH7KLVIXQFWLRQFRPSHQVDWHVIRUHOHYDWRULQWHUIHUHQFHE\DLOHURQRSHUDWLRQRUDLOHURQLQWHUIHUHQFHE\HOHYDWRURSHUDWLRQDW/RZSLWFKDQG+LSLWFKDWFROOHFWLYHSLWFK+5HWFFRQWURO6HWWKHWKURWWOHVWLFNWRWKHPD[LPXPVORZSRVLWLRQ0RYHWKHDLOHURQVWLFNWRWKHOHIWDQGULJKWDQGDGMXVWWKHDLOHURQFRPSHQVDWLRQDPRXQWVRWKDWLQWHUIHUHQFHLQWKHHOHYDWRURUSLWFKGLUHFWLRQDWWKDWWLPHLVPLQLPDO7KHOHIWDQGULJKWVLGHVFDQEHDGMXVWHGVHSDUDWHO\,IWKHLQWHUIHUHQFHLQFUHDVHVZKHQWKHFRPSHQVDWLRQDPRXQWLVLQFUHDVHGPDNHWKHFRPSHQVDWLRQGLUHFWLRQ$GMXVWWKHHOHYDWRUFRPSHQVDWLRQDPRXQWVRWKDWWKHLQWHUIHUHQFHLQWKHDLOHURQRUSLWFKGLUHFWLRQZKHQWKHHOHYDWRUVWLFNZDVPRYHGXSDQGGRZQLVPLQLPDO3HUIRUPDLOHURQDQGHOHYDWRUFRPSHQVDWLRQVLPLODUO\IRUWKHWKURWWOHVWLFNIXOOKLJKVLGH7RH[LWVHWWLQJWRXFKWKH>6ZDVK'HWDLOV@EXWWRQSpeed compensation setting procedure6HWWKHWKURWWOHVWLFNWRWKHQHXWUDOSRLQWSRVLWLRQ0RYHWKHHOHYDWRUVWLFNTXLFNO\DQGDGMXVWWKHVSHHGFRPSHQVDWLRQDPRXQWVRWKDWWKHLQWHUIHUHQFHLQWKHSLWFKGLUHFWLRQLVPLQLPDO7RH[LWVHWWLQJWRXFKWKH>6ZDVK'HWDLOV@EXWWRQNotes: ,IWKHOLQNDJHVWLFNVRXWRULVVWUHWFKHGWLJKWFRUUHFWFRPSHQVDWLRQZLOOQRWEHDSSOLHG3HUIRUPFRUUHFWLRQZLWKVXUSOXVOLQNDJH 7KHSLWFKDQJOHFKDQJHVDIWHUDGMXVWPHQW5HVHWWKHSLWFKDQJOHZKHQDFWXDOO\IO\LQJDIWHUFRPSHQVDWLRQSURFHVVLQJ$

$90 <Linkage Menu>85%Timer Model 1Timer1ModeStart/Stop SWSplit Time SWMemoryUp ؟10OFF OFFOFFOFF00ResetOFF00:00.0ڂTimer2ModeStart/Stop SWSplit Time SWMemoryUp ؟10OFF OFFOFFOFF00ResetOFF00:00.0ڂ85% 1 / 5Model 1Split TimeReturnClearTimer1Lap# Split Time1 00:00.02 00:00.03 00:00.04 00:00.05 00:00.06 00:00.0Lap# Split Time7 00:00.08 00:00.09 00:00.010 00:00.011 00:00.012 00:00.0Lap# Split Time13 00:00.014 00:00.015 00:00.016 00:00.017 00:00.018 00:00.0Lap# Split Time19 00:00.020 00:00.021 00:00.022 00:00.023 00:00.024 00:00.0ŏ0HPRU\LVWXUQHG21WKHSRZHU2))DQGDPRGHOFKDQJHZLOOQRWEHUHVHWWLPHUHLWKHUŏ7RXFKWKH>7LPHU@EXWWRQLQWKH/LQNDJH0HQXWRFDOOWKHVHWXSVFUHHQVKRZQEHORZTimer 7LPHUVHWWLQJDQGODSWLPHGLVSOD\The Timer function may be set for any desired time, LHHQJLQHUXQWLPHVSHFL¿HGWLPHVIRUFRPSHWLWLRQVetc. Two independent timers are provided for your use. The timers are stored independently with each model, meaning that when you switch between model setups,the timer associated with the new model is brought upautomatically.The timers may be set to start and stop from the motion of any switch or stick. You may set the ON and OFF directions freely. Each timer has a capacity of up to 59 minutes 59 seconds.Up timer/Down timer selection7RXFKWKHPRGHEXWWRQDQGVHOHFWWKHW\SHRIWLPHU*Each time this button is touched, it toggles between UP and DOWN.7LPHUWLPHVHWWLQJ7RXFKWKH0RGHPLQXWHVRUVHFRQGVEXWWRQ$GMXVWPHQWEXWWRQVDSSHDURQWKHVFUHHQ8VHWKHVHEXWWRQVWRVHWWKHWLPHUWLPHStart/SWtop switch setting7RXFKWKH6WDUW6WRS6:18//EXWWRQWRFDOOWKH6ZLWFK!VFUHHQDQGWKHQVHOHFWWKHVZLWFKDQGLWV21GLUHFWLRQ)RUDGHWDLOHGGHVFULSWLRQRIWKHVHOHFWLRQPHWKRGVHH>6ZLWFK6HWWLQJ0HWKRG@DWWKHEDFNRIWKLVPDQXDOEach timer may be set for count-down or count up operation with a target time. Also Split Time may be counted. If a target time is set and the timer reaches the set time, a buzzer sound for each count is generated.Countdown timers sound one short beep during the last twenty seconds and two short beeps during the last ten seconds before reaching the target, then a long tone at the target time, and continue counting with displaying a minus (-) sign. Count-up timers also beep the last twenty and ten seconds, beep the target time, and keep counting upwards until shut down.Lap time switch selection7RXFKWKH/DS6:18//EXWWRQWRFDOOWKH3URJ0L[VFUHHQDQGWKHQVHOHFWWKHVZLWFKDQGLWV21GLUHFWLRQ)RUDGHWDLOHGGHVFULSWLRQRIWKHVZLWFKVHWWLQJPHWKRGVHH>6ZLWFK6HWWLQJ0HWKRG@DWWKHEDFNRIWKLVPDQXDOTimer operationŏ7LPHUDQG7LPHUDUHVWDUWHGDQGVWRSSHGE\VWDUWVWRSVZLWFKVHWEHIRUHKDQGŏ7RFRXQWWKHODSWLPHRSHUDWHWKHODSWLPHVZLWFKVHOHFWHGEHIRUHKDQG(DFKWLPHWKLVVZLWFKLVRSHUDWHGWKHODSWLPHLVVWRUHG7RGLVSOD\WKHODSWLPHWRXFKWKHUHVSHFWLYH>/LVW@EXWWRQŏ7RUHVHWDWLPHUWRXFKWKHUHVSHFWLYH>5HVHW@EXWWRQ7RH[LWWKHVHWWLQJWRXFKWKH>7LPHU@EXWWRQŏ5HWXUQWR7LPHUVFUHHQ<Lap time list>ŏ5HWXUQWR/LQNDJH0HQX$

$91<Linkage Menu>Model 1TrimUnitLST+0%( +0%)RST+3%( +3%)LD-11%( -11%)RD-2%( -2%)LS-2%T6+0T5+0T4+0T1+0T3+0T2+0+2( -2%)RS+0%( +0%)85%Dial MonitorStep104 4 4 44CDCondition 1ŏ5HWXUQWR/LQNDJH0HQXŏ7RXFKWKH>'LDO0RQLWRU@EXWWRQLQWKH/LQNDJH0HQXWRFDOOWKHVHWXSVFUHHQVKRZQEHORZŏ7ULPFKDQJHVIURPWKHVWHSWRGLVSOD\Dial Monitor /'LVSOD\VWKHSRVLWLRQRIWKHGLDOVVOLGHUOHYHUVDQGGLJLWDOWULPDigital trim position display (T1-T6, CD)The Dial Monitor displays the current position and the operation step amount of each Digital Trim. The trim step can be set directly on the dial monitor menu.VR and slide lever position display (LST, LS, LD, RD, RS, RST)Displays the current position (black ) and last operating position (green) of the VRs and slider levers.Knob and Lever Position display (LD, RD, LS, LST, RS, RST)The Dial Monitor displays the current position and last operation position of each knob and lever. Although neither knob nor lever can hold the last operation position because of they are “analog” type, the position data during the last operation is memorized in the model memory. By moving the knob and lever to the position displayed on this monitor, the last operation position is recalled.Recalling Dial Position (LST, LS, LD, RD, RS, RST)The dial position data at the last operation is displayed for each knob and lever in this monitor. (Green arrow)0RYHWKHEODFNDUURZFXUUHQWSRVLWLRQWRWKHJUHHQDUURZSRVLWLRQE\RSHUDWLQJWKHGHVLUHGNQRERUOHYHUWRUHFDOOWKHODVWRSHUDWLQJSRVLWLRQDigital trim step amount (T1-T6, CD)The trim step of the T1-T6 and CD can be set directly on the dial monitor menu.ŏ'LJLWDOWULPVWHSDPRXQW$

92 <Linkage Menu>Please select a function.85%Function NameAileron Elevator Throttle Rudder Gear Flap Aileron2 Aileron3Aileron4 Elevator2 Flap2 Air Brake Fuel-Mix Gyro Gyro2 Gyro3Throttle2 Throttle3 Throttle4 Flap3 Flap4 Rudder2 CamberMotor Auxiliary7 Auxiliary6 Auxiliary5 Auxiliary4 Auxiliary3 Auxiliary2 Auxiliary1Please select a function.85%Function NameAileron Elevator Throttle Rudder Gear Flap Aileron2 Aileron3Aileron4 Elevator2 Flap2 Air Brake Fuel-Mix Gyro Gyro2 Gyro3Throttle2 Throttle3 Throttle4 Flap3 Flap4 Rudder2 CamberMotor Auxiliary7 Auxiliary6 Auxiliary5 Auxiliary4 Auxiliary3 Auxiliary2 Auxiliary1CloseRenameResetRenameReset10 CharactersAileronCurrentAileronDefaultAILCurrentAILDefault4 Charactersŏ7RXFKWKH>)XQFWLRQ1DPH@EXWWRQLQWKH/LQNDJH0HQXWRFDOOWKHVHWXSVFUHHQVKRZQEHORZFunction Name )XQFWLRQ1DPHFDQEHFKDQJHGThe setup screen can display functions names of upWRFKDUDFWHUVDQGXSWRFKDUDFWHUVProcedure for changing the functions nameSelect [Function Name] from the Linkage Menu.Select the function whose name you want tochange.Press the [Change name] button and enter the name in 10 characters and 4 characterseach from the displayed keyboard. After the characters are entered, press the keyboard [Return] key When the [Reset] key is pressed, the functionname is reset its original name.

$93<Linkage Menu>Telemetry 'LVSOD\LQJGDWDIURPWKHUHFHLYHUThis screen displays the data from the receiver. An alarm can also be generated according to thedata. For example, if the receiver voltage drops, the operator can be warned by a transmitter alarm.ŏ&DOOWKHIROORZLQJVHWWLQJVFUHHQE\SUHVVLQJWKH>7HOHPHWU\@EXWWRQRIWKH/LQNDJH0HQXŏ,IYROWDJHIDOOVUDWKHUWKDQWKHYROWDJHVHWXSKHUHWKHDODUPZLOORSHUDWHŏ5HFHLYHU%DWWHU\YROWDJHŏ([WHUQDO,QSXWYROWDJH(([WUD9ROWDJHFRQQHFWRUŏ7KHGLVSOD\RIWKHPD[LPXPDQGWKHPLQLPXP>&OHDU@LVUHVHWZLWKDPDOHŏ,WRSHUDWHVE\,1+→212))ŏ$VHWXSRIYLEUDWLRQ2))→HDFKW\SHWKHYLEUDWLRQZLOORSHUDWHW\SHVWRVHOHFWLRQRIWKHNLQGRIYLEUDWLRQLVSRVVLEOHŏ5HWXUQWR/LQNDJH0HQXŏ5HFHLYLQJVWDWH56%→70=ŏ5HWXUQWR7HOHPHWU\WarningDo not stare at the transmitter VFUHHQGXULQJÀLJKW*You may loose sight of the aircraft during ÀLJKWDQGLVH[WUHPHO\GDQJHURXV+DYHthe screen checked by an assistant. The pilot should not take his eyes off the aircraft.Receiver Battery Display 5.9V5.0V - 6.4V0.0V - 0.0V0.0V$

$94 <Linkage Menu>Temperature Display RPM Display ŏ7HPSHUDWXUHLVVHWXS:KHQLWEHFRPHVKLJKWHPSHUDWXUHIURPSUHVHWWHPSHUDWXUHWKHDODUPRSHUDWHVŏ530LVVHWXS:KHQLWEHFRPHVKLJK530IURPSUHVHW530WKHDODUPRSHUDWHVŏ7HPSHUDWXUH'LVSOD\ŏ530'LVSOD\ŏ7KHGLVSOD\RIWKHPD[LPXPDQGWKHPLQLPXP>&OHDU@LVUHVHWZLWKDPDOHŏ7KHGLVSOD\RIWKHPD[LPXPDQGWKHPLQLPXP>&OHDU@LVUHVHWZLWKDPDOH6HOHFWWKHW\SHRSWLFDOVHQVRURUPDJQHWLFVHQVRUQRSWLFDOVHQVRUWKHQXPEHURIDÀQLVLQSXWWHGŏ$VHWXSRIDQDOHUWRIRSHUDWLRQ,WRSHUDWHVE\,1+→212))ŏ$VHWXSRIDQDOHUWRIRSHUDWLRQ,WRSHUDWHVE\,1+→212))ŏ$VHWXSRIYLEUDWLRQ2))→HDFKW\SHWKHYLEUDWLRQZLOORSHUDWHW\SHVWRVHOHFWLRQRIWKHNLQGRIYLEUDWLRQLVSRVVLEOHŏ$VHWXSRIYLEUDWLRQ2))→HDFKW\SHWKHYLEUDWLRQZLOORSHUDWHW\SHVWRVHOHFWLRQRIWKHNLQGRIYLEUDWLRQLVSRVVLEOHŏ5HWXUQWR7HOHPHWU\ŏ5HWXUQWR7HOHPHWU\$

$95<Linkage Menu>Altitude Display ŏ$OWLWXGHLVVHWXS:KHQLWEHFRPHVKLJKDOWLWXGHIURPSUHVHWDOWLWXGHWKHDODUPRSHUDWHVŏ$OWLWXGH'LVSOD\ŏ$WPRVSKHULFSUHVVXUH'LVSOD\ŏ9DULRPHWHU'LVSOD\+RZPDQ\PHWHUULVHGHVFHQWLQVHFRQGŏ7KHGLVSOD\RIWKHPD[LPXPDQGWKHPLQLPXP>&OHDU@LVUHVHWZLWKDPDOHŏ$VHWXSRIDQDOHUWRIRSHUDWLRQ,WRSHUDWHVE\,1+→212))ŏ$VHWXSRIYLEUDWLRQ2))→HDFKW\SHWKHYLEUDWLRQZLOORSHUDWHW\SHVWRVHOHFWLRQRIWKHNLQGRIYLEUDWLRQLVSRVVLEOHŏ5HWXUQWR7HOHPHWU\Atmospheric pressure is measured by a sensor and an altitude is judged with a difference withground atmospheric pressure. Atmospheric pressure when the power supply of an altitude sensor is set to ON is displayed as a standard (0 m). [Preset] A push on a button will re-set up a standard altitude.What altitude is it?$

$96 <Linkage Menu>ŏ5HWXUQWR/LQNDJH0HQXŏ7RXFKWKH>6HQVRU@EXWWRQLQWKH/LQNDJH0HQXWRFDOOWKHVHWXSVFUHHQVKRZQEHORZSensor 9DULRXVWHOHPHWU\VHQVRUVVHWWLQJProcedure for changing the sensor of each slot No.1. Select [Sensor] from the Linkage Menu.2. Select the sensor of the slot No. to be changed.3. Select the type of displayed sensor.4. When the [Yes] key is pressed, the type of sensor is changed.*In the case of the sensor which uses more slots, it may be unable to assign.The telemetry sensor slot No. and which sensor is used at each slot can be changed at this screen.Since the sensor at each slot is determined at initialization and the same slot No. is memorized even for sensors sold separately, sensors can be used by simply connecting them to S.BUS2. When customizing the sensors yourself, perform setting at this screen.[What is a slot?]Servos are classified by CH, but sensors are classified in units called “slot”. There are slots from No. 1 to No. 31.Altitude sensor and other voluminous datasensor units use multiple slots.When 2 or more of the same kind of sensor are used, the sensors themselves must allocate unused slots and memorized the allocated slot.*Three slots of altitude sensor are used. Slot FDQQRWEHXVHGIRUDQDOWLWXGHVHQVRU$

$97<Linkage Menu>Procedure for changing the slot No. of each sensor unit1. Select [Sensor] on page 2 of the Linkage Menu.2. Call page 2 by pressing [1/2] and press [Change Slot].3. Connect the receiver battery and the sensor unit to the S.I/F connector behind the rear cover of the transmitter using a 3-way hub or 2-way cord.4. Press the [Read] key. The current slot No. is displayed.5. When a number is pressed, the [ 䂦], [ 䂰], [ 䂦䂦 ] and [ 䂰䂰 ] keys appear. Now change the desired No.6. When the [Write] key is pressed, the desired No. is written to the sensorŏ&DOOWKLVVFUHHQE\VZLWFKLQJWRSDJHE\SUHVVLQJWKH>@EXWWRQRQWKH6HQVRUVFUHHQDQGWKHQSUHVVLQJ>&KDQJH6ORW@ŏ:KHQSUHVVHGWKHFXUUHQWVORW1RLVGLVSOD\HGŏ7KHVORW1RLVZULWWHQWRWKHVHQVRUVRUVFUHHQSensorHUBor Y-adapterReceiver batteryT18MZ$

$98 <Linkage Menu>ŏ5HWXUQWR/LQNDJH0HQXŏ,ILWWXUQV21ZDUQLQJZLOOEHWROGZLWKYLEUDWLRQŏ,ILWFKDQJHVDW2))DODUPVWRSVFRPLQJRXWDWWKHWLPHRIWKHSRZHUVXSSO\21ŏ,IDWKURWWOHVWLFNXVHVWKHSRZHUVXSSO\21LQWKHVWDWHE\WKHVLGHRIDKLJKWKHQH[WVFUHHQZLOOFRPHRXWDQGDODUPZLOOVRXQG7KHWKURWWOHVWLFNVKRXOGWXUQRQDSRZHUVXSSO\LQWKHVWDWHE\WKHVLGHRIDORZDWDQ\FRVWŏ,IDWKURWWOHVWLFNLVORZHUHGDODUPZLOOVWRSDQGLWZLOOEHFRPHDFRQÀUPDWLRQVFUHHQ,WVWDUWVE\<(6ŏ7RXFKWKH>:DUQLQJ@EXWWRQLQWKH/LQNDJH0HQXWRFDOOWKHVHWXSVFUHHQVKRZQEHORZWarning 6HWWLQJRIZDUQLQJVRXQGDQGYLEUDWLRQ* If a throttle stick turns on a power power supply in the high state in case of the electric body, it may begin to turn to high rotation suddenly, and is very dangerous. We recommend you to use the warning of a throttle position with ON. Please be sure to turn on each power supply in the state where a throttle stick is slow. Warning when a power supply is turned on can be set up for every function. All initial setting isON. Please turn ON the function in which it seems that it is dangerous in accordance with the purpose of use. Alarm is stopped if the function of each item is operated at OFF.$

$99<Linkage Menu>Model 1 Condition 1 85%Date ResetDirect Key Model Menu Setting All Model SettingT1~T6, CDFunction Nameŏ5HWXUQWR/LQNDJH0HQXŏ7RXFKWKH>'DWD5HVHW@EXWWRQLQWKH/LQNDJH0HQXWRFDOOWKHVHWXSVFUHHQVKRZQEHORZData Reset0RGHOPHPRU\VHWWLQJGDWDUHVHWE\LWHPThis function is designed to allow you to reset selected portions or all of the settings saved inthe active model memory. You may individuallychoose to reset the following sets of data;T1~T6, CD:Reset the digital trim setting.*All the conditions, or the condition currently being displayed (the entire group for group setting), can be selected.Direct key:Resets direct key assignment.Data Resetting7RXFKWKHGHVLUHGEXWWRQWRUHVHWWKHVHWRIGDWD3HUIRUPWKHGDWDUHVHWWLQJDFFRUGLQJWRWKHLQVWUXFWLRQVGLVSOD\HGRQDVFUHHQ:KHQFRPSOHWHWRXFKWKH'DWD5HVHWEXWWRQWRH[LWModel menu setting:Resets all the functions in the Model Menu except Condition Select.All model setting:Resets all Linkage and Model Menu functions except for Syatem Type, Model Select, and Model Type.Initial setting of a motor channel is reverse.After reset is reverse.$

$100 <Linkage Menu>Condition Hold &RQGLWLRQKROGIXQFWLRQ+HOLFRSWHURQO\7KLVIXQFWLRQPD\EHXVHGWR¿[WKHPD[LPXPspeed of the engine so that you may adjust flight conditions when the engine is running. An alarm indicates that the function is operating. It will prevent the engine from racing dangerously when adjusting the Idle-Up settings. While this function is active, the throttle servo position is fixed at the point where you operate when the function is activated. You must deactivate this function when you are through making adjustments.The system will not allow you to activate/deactivate this function in either of the following states: :KHQDQ\RIWKHIOLJKWFRQGLWLRQVZLWFKHVDUHRQ :KHQWKHWKURWWOHVWLFNLVKLJKHUWKDQWKHSRLQWTo activate/deactivate Condition hold:(Home screen)6HWWKHWKURWWOHVWLFNORZHUWKDQWKHSRLQW3XVKWKHGLUHFWNH\6&RQG+ROGWRDFWLYDWHWKHFRQGLWLRQKROGIXQFWLRQ*When this function is active, "Condition Hold is active" appears on the screen.(LINKAGE menu/MODEL menu)6HWWKHWKURWWOHVWLFNORZHUWKDQWKHSRLQW3XVKWKH,1+RUWKHGLUHFWNH\6EXWWRQWRDFWLYDWHWKHFRQGLWLRQKROGIXQFWLRQ*Operation is displayed at the bottom of the menu.Function ON: "ON" is displayed.Function OFF: "INH" is displayed.$

Futaba T18MZ-24G Radio Control User Manual

Futaba Corporation Radio Control

Contents

User manual-2(Page 31-100)

Navigation menu

Namespaces

Views

Navigation