Futaba FMR-03-24G Radio Control User Manual 3

Futaba Corporation Radio Control 3

Contents

User Manual 3

121＜Model Menu (Airplane/Glider Functions) ＞Reference FMT-03 is equipped with a stick of multi-copter exclusive use. Therefore it's unsuitable for use of an airplane, a glider and a helicopter.S1●SelectthefunctionnameandreturntotheprecedingscreenbypushingtheRTNbuttonorpushingtheHome/Exitbutton.<Editdial>FLP 2(Camber Flap)FLP 1(Camber Flap)FLP 3(Brake Flap) FLP 4(Brake Flap)FLAP SETTING [Correspondingmodeltype]:Airplane/glider,2apsormore]The up/down travel of each flap (camber flaps: FLP1/2, brake flaps: FLP3/4) can be adjusted independently at each servo according to the wing type.●TheoperationreferencepointofeachapcanbeoffsetThe camber aps of a 4-ap model can be mixed with the brake aps. (Brake FLP to camber FLP)●AnON/OFFswitchcanbeset. <Wing type: 4 aps screen>*The display screen is an example. The actual screen depends on the model type.Setting method●Movethecursortotheflap(FLP)1~4upordownitemaccordingtothewingtypeandpushtheRTNbuttontoswitchtothedatainputmode. Adjustthetravelindependently.●Tooffsettheoperationreferencepointofeachflap,movethecursortothecorrespondingoffsetitem.Usetheeditdialtooffsetthereferencepoint. PushtheRTNbuttontoendadjustmentandreturntothecursormovemode.●Operationreferencepointoffset●Upside/Downsideadjustment●Group/singlemodeswitching(For more information, refer to the description at the back of this manual.)●WhenusingbrakeFLPtocamberFLPmixing,movethecursortothe[ACT/INH]itemandturntheeditdialtotheleftandpushtheRTNbutton.(ONisdisplayed.) Whensettingaswitch,movethecursortothe[--]itemoftheswitchandpushtheRTNbuttontocalltheselectionscreen,andthenselecttheswitchandsetitsONdirection.(AlwaysONat"--"setting) (Foradescriptionoftheswitchselectionmethod,seethedescriptionatthebackofthismanual.)(CAMBERFLPsettingscreen)(BRAKEFLPsettingscreen)(B.FLPtoC.FLPsettingscreen)●Select[FLAPSETTING]atthemodelmenuandcallthesetupscreenshownbelowbypushingtheRTNbutton.Scrolling●Movingcursor●Selectingmode●Adjustingvalue●PushtheS1buttontocallnextpage.
122 ＜Model Menu (Airplane/Glider Functions) ＞Reference FMT-03 is equipped with a stick of multi-copter exclusive use. Therefore it's unsuitable for use of an airplane, a glider and a helicopter.S1●SelectthefunctionnameandreturntotheprecedingscreenbypushingtheRTNbuttonorpushingtheHome/Exitbutton.<Editdial>AIL 3(Chip Aileron) AIL 4(Chip Aileron)AIL1(Main Aileron) AIL 2(Main Aileron)FLP 2(Camber Flap)FLP 1(Camber Flap)AIL to CAMB.FLP [Correspondingmodeltype]:Airplane/glider,2ailerons+2apsormoreThis mix operates the camber flaps (FLP1/2) in the aileron mode. When the aileron stick is manipulated, the ailerons and camber flaps perform aileron operation simultaneously and the operation characteristic of the roll axis is improved.●Theaileronleft/rightmixingrateofeachapservocanbene-tuned.●Amixingcurvecanbeset.●AnON/OFFswitchcanbeset.●Linkingispossible:Linkthismixtoothermixes.●Mixingcurvesetting*For a description of the curve setting method, see the description at the back of this manual.●Adjustmentofeachapservo●Left/rightoveralladjustmentatRateAandRateBSetting method●MovethecursortotheACT/INHitemandpushtheRTNbuttontoswitchtothedatainputmode. TurntheeditdialtotheleftandpushtheRTNbutton.(ONisdisplayed.)●Whensettingaswitch,movethecursortothe[--]itemoftheswitchandpushtheRTNbuttontocalltheselectionscreen,andthenselecttheswitchandsetitsONdirection.(AlwaysONat"--"setting) (Foradescriptionoftheswitchselectionmethod,seethedescriptionatthebackofthismanual.)●MovethecursortotheleftorrightitemofeachapservoandpushtheRTNbutton toswitchtothedatainputmode. Adjustthemixingratewiththeeditdial. PushtheRTNbuttontoendadjustmentandreturntothecursormovemode.*When the mixing direction is reversed by the linkage, adjustments can be made by changing the mixing rate polarity (+ or -).●Amixingcurvecanbeset. (Foradescriptionofthemixingcurvesettingmethod,seethedescriptionatthebackofthismanual.)●Tosetlinking,movethecursortothe[LINK]itemandpushtheRTNbuttontoswitchtothedatainputmode. SetittoONandpushtheRTNbutton.(Currently selected condition name)●Select[AILtoCAMB.FLP]atthemodelmenuandcallthesetupscreenshownbelowbypushingtheRTNbutton.●Group/singlemodeswitching(For more information, refer to the description at the back of this manual.)*The display screen is an example. The actual screen depends on the model type.Scrolling●Movingcursor●Selectingmode●Adjustingvalue●PushtheS1buttontocallnextpage.
123＜Model Menu (Airplane/Glider Functions) ＞Reference FMT-03 is equipped with a stick of multi-copter exclusive use. Therefore it's unsuitable for use of an airplane, a glider and a helicopter.S1●SelectthefunctionnameandreturntotheprecedingscreenbypushingtheRTNbuttonorpushingtheHome/Exitbutton.<Editdial>AIL 3(Chip Aileron) AIL 4(Chip Aileron)AIL1(Main Aileron) AIL 2(Main Aileron)FLP 3(Brake Flap) FLP 4(Brake Flap)AIL to BRAKEFLP [Correspondingmodeltype]:Airplane/glider,4apsormoreThis mix operates the brake flaps (FLP3/4) in the aileron mode. When the aileron stick is manipulated, the aileron and brake flaps perform the aileron operation simultaneously and the operation characteristic of the roll axis is improved.●Theaileronleftandrightmixingratescanbeadjustedforeachapservo.●Amixingcurvecanbeset.●MixingduringightcanbeturnedON/OFFbysettingaswitch.(AlwaysONat[--]setting)●Linkingcanbeset:Linkthismixtoothermixes.●Setting method●MovethecursortotheACT/INHitemandpushtheRTNbuttontoswitchtothedatainputmode. TurntheeditdialtotheleftandpushtheRTNbutton.(ONisdisplayed.)●Whensettingaswitch,movethecursortothe[--]itemoftheswitchandpushtheRTNbuttontocalltheselectionscreen,andthenselecttheswitchandsetitsONdirection.(AlwaysONat"--"setting) (Foradescriptionoftheswitchselectionmethod,seethedescriptionatthebackofthismanual.)●MovethecursortotheleftorrightbuttonofeachapservoandpushtheRTNbutton toswitchtothedatainputmode. Adjustthemixingratewiththeeditdial. PushtheRTNbuttontoendadjustmentandreturntothecursormovemode.*When the mixing direction is reversed by the linkage, adjustments can be made by reversing the mixing rate polarity (+ or -).●Amixingcurvecanbeset. (Foradescriptionofthecurvesettingmethod,seethedescriptionatthebackofthismanual.)●Tosetlinking,movethecursortotheLinkitemandpushtheRTNbuttontoswitchtothedatainputmode. SetittoONandpushtheRTNbutton.●Mixingcurvesetting*For a description of the curve setting method, see the description at the back of this manual.●Adjustmentofeachapservo●Left/rightoveralladjustmentatRateAandRateB(Currently selected condition name)●Select[AILtoBRAKEFLP]atthemodelmenuandcallthesetupscreenshownbelowbypushingtheRTNbutton.●Group/singlemodeswitching(For more information, refer to the description at the back of this manual.)*The display screen is an example. The actual screen depends on the model type.Scrolling●Movingcursor●Selectingmode●Adjustingvalue●PushtheS1buttontocallnextpage.
124 ＜Model Menu (Airplane/Glider Functions) ＞Reference FMT-03 is equipped with a stick of multi-copter exclusive use. Therefore it's unsuitable for use of an airplane, a glider and a helicopter.S1●SelectthefunctionnameandreturntotheprecedingscreenbypushingtheRTNbuttonorpushingtheHome/Exitbutton.<Editdial>RUDDER 2RUDDER RUDDERV-TAILRUDDER 2WingletRUDDER 1Wingletat Flying wing at Flying wing( ) ( )AIL 3 AIL 3(Chip Aileron) (Chip Aileron)AIL1(Main Aileron) AIL 2(Main Aileron)AIL to RUD [Correspondingmodeltype]:Airplane/glider,generalUse this mix when you want to mix the rudders with aileron operation. ●Amixingcurvecanbeset.●MixingduringightcanbeturnedON/OFFbysettingaswitch.(AlwaysONat[--]setting)●Themixingratecanbene-tunedbysettingaVR.Setting method●MovethecursortotheACT/INHitemandpushtheRTNbuttontoswitchtothedatainputmode. TurntheeditdialtotheleftandpushtheRTNbutton.(ONisdisplayed.)●Whensettingaswitch,movethecursortothe[--]itemoftheswitchandpushtheRTNbuttontocalltheselectionscreen,andthenselecttheswitchandsetitsONdirection.(AlwaysONat"--"setting) (Foradescriptionoftheswitchselectionmethod,seethedescriptionatthebackofthismanual.●WhensettingaVR,movethecursortotheFineTuning"--"itemandpushtheRTNbuttontocalltheselectionscreen,andthenselecttheVR.Theadjustmentratecanbeset.TheVRoperationmodecanalsobeselected.[FinetuningVRoperationmode][LIN.] Mixingrate0%atcenterofVR.WhentheVRisturnedclockwiseandcounterclockwise,themixingrateincreasesanddecreases,respectively.[ATL+]Mixingrate0%atleftendofVR.WhentheVRisturned,themixingrateincreases.[ATL-] Mixingrate0%at rightendofVR.WhentheVRisturned,themixingrateincreases.[SYM.]WhentheVRisturnedtotheleftorrightoftheneutralposition,themixingrateincreases.●Mixingcurvesetting*For a description of the curve setting method, see the description at the back of this manual. ●Left/rightoveralladjustmentatRateAandRateB(Currently selected condition name)●Select[AILtoRUD]atthemodelmenu andcallthesetupscreenshownbelowbypushingtheRTNbutton.●Group/singlemodeswitching(For more information, refer to the description at the back of this manual.)*The display screen is an example. The actual screen depends on the model type.●FinetuningVRsetting●Adjustmentrate●Operationmode●Amixingcurvecanbeset. (Foradescriptionofthecurvesettingmethod,seethedescriptionatthebackofthismanual.)Scrolling●Movingcursor●Selectingmode●Adjustingvalue●PushtheS1buttontocallnextpage.
125＜Model Menu (Airplane/Glider Functions) ＞Reference FMT-03 is equipped with a stick of multi-copter exclusive use. Therefore it's unsuitable for use of an airplane, a glider and a helicopter.S1●SelectthefunctionnameandreturntotheprecedingscreenbypushingtheRTNbuttonorpushingtheHome/Exitbutton.<Editdial>ELEVATOR ELEVATOR 2AILVATORAIR BRAKEV-TAILELEVATOR ELEVATOR 2AIRBRAKE to ELE [Correspondingmodeltype]:Airplane/glider,generalThis mix is used when you want to mix the elevators with airbrake (spoiler) operation. It raises the elevators to correct for dropping of the nose during airbrake operation.*This function does not operate when airbrake is not assigned at the Function menu in the Linkage Menu.●TheRate1side/Rate2sidemixingratewiththeelevatorservoscanbeadjusted.●Amixingcurvecanbeset.●MixingduringightcanbeturnedON/OFFbysettingaswitch.(AlwaysONat[--]setting)●Themixingratecanbene-tunedbysettingaVR.●FinetuningVRsetting●Group/singlemodeswitching(For more information, refer to the description at the back of this manual.)●OveralladjustmentbyRateAandRateB.(Currently selected condition name)●Select[AIRBRAKEtoELE]atthemodelmenuandcallthesetupscreenshownbelowbypushingtheRTNbutton.●Mixingcurvesetting*For a description of the curve setting method, see the description at the back of this manual.●Adjustmentrate●Operationmode●Adjustmentofeachelevatorservo*The display screen is an example. The actual screen depends on the model type.Scrolling●Movingcursor●Selectingmode●Adjustingvalue●PushtheS1buttontocallnextpage.
126 ＜Model Menu (Airplane/Glider Functions) ＞Reference FMT-03 is equipped with a stick of multi-copter exclusive use. Therefore it's unsuitable for use of an airplane, a glider and a helicopter.Setting method●MovethecursortotheACT/INHitemandpushtheRTNbuttontoswitchtothedatainputmode. TurntheeditdialtotheleftandpushtheRTNbutton.(ONisdisplayed.)●Whensettingaswitch,movethecursortothe[--]itemoftheswitchandpushtheRTNbuttontocalltheselectionscreen,andthenselecttheswitchandsetitsONdirection.(AlwaysONat"--"setting) (Foradescriptionoftheswitchselectionmethod,seethedescriptionatthebackofthismanual.●WhensettingaVR,movethecursortotheFinetuning"--"itemandpushtheRTNbuttontocalltheselectionscreen,andthenselecttheVR.Theadjustmentratecanbeset.TheVRoperationmodecanalsobeset. (ForadescriptionofthenetuningVRsettingmethod,seethedescriptionatthebackofthismanual.)●Amixingcurvecanbeset. (Foradescriptionofthecurvesettingmethod,seethedescriptionatthebackofthismanual.)[FinetuningVRoperationmode][LIN.] Mixingrate0%atcenterofVR.WhentheVRisturnedclockwiseandcounterclockwise,themixingrateincreasesanddecreases,respectively.[ATL+]Mixingrate0%atleftendofVR.WhentheVRisturned,themixingrateincreases.[ATL-] Mixingrate0%at rightendofVR.WhentheVRisturned,themixingrateincreases.[SYM.]WhentheVRisturnedtotheleftorrightoftheneutralposition,themixingrateincreases.
127＜Model Menu (Airplane/Glider Functions) ＞Reference FMT-03 is equipped with a stick of multi-copter exclusive use. Therefore it's unsuitable for use of an airplane, a glider and a helicopter.S1●SelectthefunctionnameandreturntotheprecedingscreenbypushingtheRTNbuttonorpushingtheHome/Exitbutton.<Editdial>RUDDER 2RUDDER RUDDERV-TAILRUDDER 2WingletRUDDER 1Wingletat Flying wing at Flying wing( ) ( )AIL 3 AIL 3(Chip Aileron) (Chip Aileron)AIL1(Main Aileron) AIL 2(Main Aileron)RUD to AIL [Correspondingmodeltype]:Airplane/glider,generalThis function is used when you want to mix the ailerons with rudder operation. It is used when rudder is applied during roll maneuvers, knife edge, etc. of stunt planes. It can be used to bank scale models, large models, etc. like a full size plane.●Amixingcurvecanbeset.●MixingduringightcanbeturnedON/OFFbysettingaswitch.(AlwaysONat[--]setting)●Linkingcanbeset:Linkthismixtoothermixes.●Themixingratecanbene-tunebysettingaVR.Setting method●MovethecursortotheACT/INHitemandpushtheRTNbuttontoswitchtothedatainputmode. TurntheeditdialtotheleftandpushtheRTNbutton.(ONisdisplayed.)●Whensettingaswitch,movethecursortothe[--]itemoftheswitchandpushtheRTNbuttontocalltheselectionscreen,andthenselecttheswitchandsetitsONdirection.(AlwaysONat"--"setting) (Foradescriptionoftheswitchselectionmethod,seethedescriptionatthebackofthismanual.●WhensettingaVR,movethecursortotheFinetuning"--"itemandpushtheRTNbuttontocalltheselectionscreenandthenselecttheVR.Theadjustmentratecanbeset,.TheVRoperationmodecanalsobeset. (ForadescriptionofthenetuningVRsettingmethod,seethedescriptionatthebackofthismanual.)●Amixingcurvecanbeset. (Foradescriptionofthecurvesettingmethod,seethedescriptionatthebackofthismanual.)●Whenlinking:movethecursortothe[LINK]itemandpushtheRTNbuttontoswitchtothedatainputmode.TurntheeditdialtotheleftandpushtheRTNbutton.(ONisdisplayed.)●Mixingcurvesetting*For a description of the curve setting method, see the description at the back of this manual.●Left/rightoveralladjustmentatRateAandRateB(Currently selected condition name)●Select[RUDtoAIL]atthemodel menuandcallthesetupscreenshownbelowbypushingtheRTNbutton.●Group/singlemodeswitching(For more information, refer to the description at the back of this manual.)*The display screen is an example. The actual screen depends on the model type.●FinetuningVRsetting●Adjustmentrate●Operationmode[FinetuningVRoperationmode][LIN.] Mixingrate0%atcenterofVR.WhentheVRisturnedclockwiseandcounterclockwise,themixingrateincreasesanddecreases,respectively.[ATL+]Mixingrate0%atleftendofVR.WhentheVRisturned,themixingrateincreases.[ATL-] Mixingrate0%at rightendofVR.WhentheVRisturned,themixingrateincreases.[SYM.]WhentheVRisturnedtotheleftorrightoftheneutralposition,themixingrateincreases.Scrolling●Movingcursor●Selectingmode●Adjustingvalue●PushtheS1buttontocallnextpage.
128 ＜Model Menu (Airplane/Glider Functions) ＞Reference FMT-03 is equipped with a stick of multi-copter exclusive use. Therefore it's unsuitable for use of an airplane, a glider and a helicopter.S1●SelectthefunctionnameandreturntotheprecedingscreenbypushingtheRTNbuttonorpushingtheHome/Exitbutton.<Editdial>CAMBER MIX [Correspondingmodeltype]:Airplane/glider,2aileronsormoreThis function adjusts the AFR (D/R) rate of camber operation which operates the wing camber (ailerons, camber flaps, brake flaps) in the negative and positive directions. The aileron, flap, and elevator rates can also be adjusted independently by curve, and attitude changes caused by camber operation can be corrected.*Initial setting assigns camber operation to side lever LS.●Theup/downsideratesoftheaileron,ap,andelevatorservoscanbeadjustedbycurve.Whenthemixingdirectionisreversedbythelinkage,adjustmentscanbemadebychangingthemixingratepolarity(+or-).●MixingduringightcanbeturnedON/OFFbysettingaswitch.(AlwaysONat[--]setting)●Adelaycanbesetforeachcondition.AcutswitchwhichcanturnOFFthedelayfunctioncanbeset.●Thespeedoftheaileron,ap,andelevatorservoscanbeset.(INside/OUTside)●Conditiondelaycutswitch●Conditiondelaysetting●CamberAFR(D/R)setupscreencall(For a description of the setting method, refer to the AFR function.)●Servospeedsetting(For a description of the setting method, see the description at the back of this manual.)●OveralladjustmentbyRateAandRateB●Aileronrateadjustment(Currently selected condition name)●Select[CAMBERMIX]atthemodelmenuandcallthesetupscreenshownbelowbypushingtheRTNbutton.●Mixingcurvesetting*For a description of the curve setting method, see the description at the back of this manual.*The display screen is an example. The actual screen depends on the model type.(Curve/ratesettingscreen)Scrolling●Movingcursor●Selectingmode●Adjustingvalue●PushtheS1buttontocallnextpage.
129＜Model Menu (Airplane/Glider Functions) ＞Reference FMT-03 is equipped with a stick of multi-copter exclusive use. Therefore it's unsuitable for use of an airplane, a glider and a helicopter.AIL 3(Chip Aileron) AIL 4(Chip Aileron)AIL1(Main Aileron) AIL 2(Main Aileron)FLP 2(Camber Flap)FLP 1(Camber Flap)ELEVATOR ELEVATOR 2V-TAILELEVATOR ELEVATOR 2AILVATORFLP 3(Brake Flap) FLP 4(Brake Flap)Setting method●MovethecursortotheACT/INHitemandpushtheRTNbuttontoswitchtothedatainputmode. TurntheeditdialtotheleftandpushtheRTNbutton.(ONisdisplayed.)●Whensettingaswitch,movethecursortothe[--]itemoftheswitchandpushtheRTNbuttontocalltheselectionscreen,andthenselecttheswitchandsetitsONdirection.(AlwaysONat"--"setting) (Foradescriptionoftheswitchselectionmethod,seethedescriptionatthebackofthismanual.)●Whensettingaconditiondelay,movethecursortothe[COND.DELAY]itemandpushtheRTNbuttontoswitchtothedatainputmode. Setthedelaywiththeeditdial. PushtheRTNbuttontoendadjustmentandreturntothecursormovemode. Whensettingacutswitch,movethecursorto[CUT-SW]itemandpushtheRTNbuttontocalltheselectionscreen,andthenselecttheswitchandsetitsONdirection.(AlwaysONat[--]setting) (Foradescriptionoftheconditiondelayfunction,seethedescriptionatthebackofthismanual.)●CamberAFR(D/R)screencall MovethecursortotheCamberAFRitemandpushtheRTNbuttontocallthesetupscreen.(Foradescriptionofthesetupmethod,seethedescriptionatthebackofthismanual.)(Curve/ratesetupscreen)●Thecurveandrateareadjustedbycallingtheaileron,flap,andelevatorcurve/ratescreens. Therateandcurveofeachservocanbesetbycallingeachscreen.(Foradescriptionofthecurvesettingmethod,seethedescriptionatthebackofthismanual.) Theservospeedcanalsobeadjusted.
130 ＜Model Menu (Airplane/Glider Functions) ＞Reference FMT-03 is equipped with a stick of multi-copter exclusive use. Therefore it's unsuitable for use of an airplane, a glider and a helicopter.S1●SelectthefunctionnameandreturntotheprecedingscreenbypushingtheRTNbuttonorpushingtheHome/Exitbutton.<Editdial>ELE to CAMBER [Correspondingmodeltype]:Airplane/glider,2aileronsormoreThis function is used when you want to mix the camber aps with elevator operation. When used, the aps are lowered by up elevator, and lift can be increased.Note: Tailless wing elevator can be operated when this mix is activated.●Amixingcurvecanbeset.●MixingduringightcanbeturnedON/OFFbysettingaswitch.(AlwaysONat[--]setting)●Themixingratecanbene-tunedbysettingaVR.●Aileronsandapsrateadjustment1. SelecttherateboxandpushtheRTNbuttontoswitchtothedatainputmode.2. Adjusttheratesby scrolling theeditdial.3. PushtheRTN button to endadjustmentandreturntothecursormovemode.Setting method●MovethecursortotheACT/INHitemandpushtheRTNbuttontoswitchtothedatainputmode. TurntheeditdialtotheleftandpushtheRTNbutton.(ONisdisplayed.)●Whensettingaswitch,movethecursortothe[--]itemoftheswitchandpushtheRTNbuttontocalltheselectionscreen,andthenselecttheswitchandsetitsONdirection.(AlwaysONat"--"setting) (Foradescriptionoftheswitchselectionmethod,seethedescriptionatthebackofthismanual.)●WhensettingaVR,movethecursortotheFinetuning"--"itemandpushtheRTNbuttontocalltheselectionscreen,andthenselecttheVR.Theadjustmentratecanbeset. TheVRoperationmodecanalsobeselected.●Amixingcurvecanalsobeset. (Foradescriptionofthecurvesettingmethod,seethedescriptionatthebackofthismanual.)●Group/singlemodeswitching(For more information, refer to the description at the back of this manual.)●OveralladjustmentbyRateAandRateB.(Currently selected condition name)●Select[ELEtoCAMBER]atthemodelmenuandcallthesetupscreenshownbelowbypushingtheRTNbutton.●Mixingcurvesetting*For a description of the curve setting method, see the description at the back of this manual.*The display screen is an example. The actual screen depends on the model type.●FinetuningVRsetting●Adjustmentrate●OperationmodeScrolling●Movingcursor●Selectingmode●Adjustingvalue●PushtheS1buttontocallnextpage.
131＜Model Menu (Airplane/Glider Functions) ＞Reference FMT-03 is equipped with a stick of multi-copter exclusive use. Therefore it's unsuitable for use of an airplane, a glider and a helicopter.S1●SelectthefunctionnameandreturntotheprecedingscreenbypushingtheRTNbuttonorpushingtheHome/Exitbutton.<Editdial>ELEVATOR ELEVATOR 2V-TAILELEVATOR ELEVATOR 2AILVATORFLP 2(Camber Flap)FLP 1(Camber Flap)CAMB.FLP to ELE [Correspondingmodeltype]:Airplane/glider, 2ailerons+1apormoreThis mixing is used to correct changes (elevator direction) generated when the camber aps (speed aps) are used.●Theelevatorservosupside/downsideratecanbeadjusted.Whenthemixingdirectionisreversedbythelinkage,adjustmentscanbemadebychangingthemixingratepolarity(+or–).●Amixingcurvecanbeset.●MixingduringightcanbeturnedON/OFFbysettingaswitch.(AlwaysONat[--]setting)●Themixingratecanbene-tunedbysettingaVR.●ElevatorrateadjustmentSetting method●MovethecursortotheACT/INHitemandpushtheRTNbuttontoswitchtothedatainputmode. TurntheeditdialtotheleftandpushtheRTNbutton.(ONisdisplayed.)●Whensettingaswitch,movethecursortothe[--]itemoftheswitchandpushtheRTNbuttontocalltheselectionscreen,andthenselecttheswitchandsetitsONdirection.(AlwaysONat"--"setting) (Foradescriptionoftheswitchselectionmethod,seethedescriptionatthebackofthismanual.●MovethecursortotheelevatorservosleftandrightitemandpushtheRTNbutton toswitchtothedatainputmode.Adjustthemixingratewiththeeditdial. PushtheRTNbuttontoendadjustmentandreturntothecursormovemode.*When the mixing direction is reversed by the linkage, adjustments can be made by changing the mixing rate polarity (+ or –).●WhensettingaVR,movethecursortotheFinetuning"--"itemandpushtheRTNbuttontocalltheselectionscreen,andthenselecttheVR.TheVRoperationmodecanbeselected.●Amixingcurvecanbeset. (Foradescriptionofthecurvesettingmethod,seethedescriptionatthebackofthismanual.)●OveralladjustmentbyRateAandRateB.(Currently selected condition name)●Select[CAMB.FLPtoELE]atthemodelmenuandcallthesetupscreenshownbelowbypushingtheRTNbutton.●Mixingcurvesetting*For a description of the curve setting method, see the description at the back of this manual.*The display screen is an example. The actual screen depends on the model type.●FinetuningVRsetting●Adjustmentrate●Operationmode●Group/singlemodeswitching(For more information, refer to the description at the back of this manual.)Scrolling●Movingcursor●Selectingmode●Adjustingvalue●PushtheS1buttontocallnextpage.
132 ＜Model Menu (Airplane/Glider Functions) ＞Reference FMT-03 is equipped with a stick of multi-copter exclusive use. Therefore it's unsuitable for use of an airplane, a glider and a helicopter.S1●SelectthefunctionnameandreturntotheprecedingscreenbypushingtheRTNbuttonorpushingtheHome/Exitbutton.<Editdial>BUTTERFLY [Correspondingmodeltype]:Glider,2aileronsormoreThis function allows powerful brake operation by simultaneously raising the left and right ailerons and lowering the flaps (camber flap, brake ap).This setting will allow the ailerons to be raised while the flaps are simultaneously lowered. Butterfly (crow) produces an extremely efficient landing configuration by accomplishing the following: 1.Slowtheaircraft’svelocity.2.Providewashoutatthewingtipstoreducethetendencytotipstall.3.Createmorelifttowardthecenterofthewingallowingittoyataslowerspeed●MixingduringightcanbeturnedON/OFFbysettingaswitch.(AlwaysONat[--]setting)●Thebutteryoperationreferencepointcanbeoffset.WhentheRTNbuttonispushedwiththeoffsetitemselectedwhenoperatedtothepositiontobechanged,thereferencepointisoffset.Ifthereferencepointisoffsettoomuch,unexpectedoperationmaybeperformed.●Theaileronsandapsoperationspeedcanbeadjusted.(INside/OUTside)●Adelaycanbesetforeachcondition.AcutswitchwhichcanturnOFFthedelayfunctioncanalsobeset.●Thedifferentialratecanbeadjusted.*When servo binding occurs when setting the ailerons and aps in buttery mixing, use the AFR function to adjust the rudder angle.●Whenoffsettingthebutterflyoperationreferencepoint,operatetothepointyouwanttochangeandthenpresstheEDITbuttonfor1second."INITIALIZEELEVATORCURVE?"isdisplayed.PleasechoosewhethertoinitializebyYES,ornottoinitializebyNO.●Differentialrateadjustment●Toelevatorcorrectionsetupscreen●CallstheButteryAFR(D/R)setupscreen(For a description of the setting method, see the description at the back of this manual.)●Aileronandapservosspeedsetting(For a description of the setting method, see the description at the back of this manual.)●Conditiondelaysettingandcutswitchsetting(For a description of the setting method, see the description at the back of this manual.)● SelecttheMixingRateAILandFLP box andpushtheRTNbuttontoswitchtothedatainputmode.Adjustthemixingrates. PushtheRTNbuttontoendadjustmentandreturntothecursormovemode.(Currently selected condition name)●Select[BUTTERFLY]atthemodelmenuand callthesetupscreenshownbelowbypushingtheRTNbutton.*The display screen is an example. The actual screen depends on the model type.●Whenusingthisfunction,movethecursortothe[ACT/INH]itemandpushtheRTNbuttontoswitchtothe datainputmode.TurntheeditdialtotheleftandpushtheRTNbutton.(ONisdisplayed.)●Group/singlemodeswitching(For more information, see the description at the back of this manual.)●Whensettingaswitch,selecttheSWITCH[--]boxandpushtheRTNbuttontoswitchtothedatainputmode.PresstheEDITbuttontocalltheselectionscreen,andthenselecttheswitchandsetitsONdirection.Scrolling●Movingcursor●Adjustingvalue●PushtheS1buttontocallnextpage.
133＜Model Menu (Airplane/Glider Functions) ＞Reference FMT-03 is equipped with a stick of multi-copter exclusive use. Therefore it's unsuitable for use of an airplane, a glider and a helicopter.AIL 3(Chip Aileron) AIL 4(Chip Aileron)AIL1(Main Aileron) AIL 2(Main Aileron)FLP 2(Camber Flap)FLP 1(Camber Flap)ELEVATOR ELEVATOR 2V-TAILELEVATOR ELEVATOR 2AILVATORFLP 3(Brake Flap) FLP 4(Brake Flap)(Elevatorcorrectionratesetupscreen)●Servospeedsetting(For a description of the setting method, see the description at the back of this manual.)●OveralladjustmentbyRateAandRateB●Elevatorrateadjustment●Mixingcurvesetting*For a description of the curve setting method, see the description at the back of this manual.
134 ＜Model Menu (Airplane/Glider Functions) ＞Reference FMT-03 is equipped with a stick of multi-copter exclusive use. Therefore it's unsuitable for use of an airplane, a glider and a helicopter.S1●SelectthefunctionnameandreturntotheprecedingscreenbypushingtheRTNbuttonorpushingtheHome/Exitbutton.<Editdial>TRIM MIX 1/2 [Correspondingmodeltype]:Glider,2aileronsormoreThese functions call the ailerons, elevators, and aps (camber aps, brake aps) trim offset rates preset according to the ight state. The amount of ailerons, elevator, and flaps (camber ap, brake ap) trim offset can be set to a switch.As an example Trim Mix 1 can be set up for launching, with speed aps and ailerons dropped, and a slight amount of up elevator. Trim mix 2 can be used for high speed flying, with both ailerons and speed aps reexed slightly, and a bit of down elevator. The trim functions can be activated during ight by setting a switch. To prevent sudden trim changes when switching ight conditions, a delay can be set to provide a smooth transition between the two. Trim Mix 2 will have priority over Trim Mix 1.●WhenanetuningVRissetonthenextpage,theaileronsapsandelevatorstrimratescanbeadjusted. MovethecursortothecorrespondingsettingitemandpushtheRTNbuttontoswitchtothedatainputmode.adjusttheratewiththeeditdial. PushtheRTNbuttontoendadjustmentandreturntothecursormovemode.●Theailerons,aps,andelevatorsoffsetratecanbeadjusted. MovethecursortothecorrespondingsettingitemandpushtheRTNbuttontoswitchtothedatainputmode.Adjusttheratewiththeeditdial. PushtheRTNbuttontoendadjustmentandreturntothecursormovemode.Example1.MovetotheACT/INHitemandpushtheRTNbuttontoswitchtothedatainputmode.Setthetrimmixfunctionto[ON].*When separating the settings for each condition, move to the [GROUP] item and set it to [Single].2.SelecttheON/OFFswitch.3.Selectthe[Manual]or[Auto]mode. Inthe[Auto] mode,alsoselectanautoSW.Thisswitchcanbelinkedtoastick,etc.<Speed> In:TheoperationspeedatswitchONcanbeset. Out:ThereturnspeedatswitchOFFcanbeset.<FineTuning> TheoffsetratecanbevariedintheFineTuningnumericrangesetatscreen[5/5]by VR,etc.selection.<ConditionDelay> Whenightconditionsareset,theoperationspeedcanbesetforeachcondition.Conditiondelayoperationcanbeinterruptedandeachrudderquicklyreturnedtoitsoriginalpositionbyselectingacutswitch.(Currently selected condition name)●Select[TRIMMIX1or2]atthemodelmenuandcallthesetupscreenshownbelowbypushingtheRTNbutton.*The display screen is an example. The actual screen depends on the model type.Scrolling●Movingcursor●Adjustingvalue●PushtheS1buttontocallnextpage.
135＜Model Menu (Airplane/Glider Functions) ＞Reference FMT-03 is equipped with a stick of multi-copter exclusive use. Therefore it's unsuitable for use of an airplane, a glider and a helicopter.●Whenusingthisfunction,movethecursortothe[ACT/INH]itemandpushtheRTNbuttontoswitchtothedatainputmode.TurntheeditdialtotheleftandpushtheRTNbutton.(ONisdisplayed.)●Group/singlemodeswitching(For more information, see the description at the back of this manual.)●WhenusingafinetuningVR,movethecursortothisitemandpushtheRTNbuttontocalltheselectionscreen. SelecttheVRandpushtheRTNbutton.●Conditiondelaysetting(foradescriptionofthesettingmethod,seethedescriptionatthebackofthismanual)andcutswitchsetting.●Ailerons,flaps,anelevatorsservospeedsetting(For a description of the setting method, see the description at the back of this manual.)●Manual/AutomodeselectionManual:SwitchesthefunctionON/OFFbyswitchAuto:Trimmixfunctioncallcanbelinkedtoastick,etc.Astickswitch,etc.separatefromthefunctionON/OFFswitchisset.AIL 3(Chip Aileron) AIL 4(Chip Aileron)AIL1(Main Aileron) AIL 2(Main Aileron)FLP 2(Camber Flap)FLP 1(Camber Flap)ELEVATOR ELEVATOR 2V-TAILELEVATOR ELEVATOR 2AILVATORFLP 3(Brake Flap) FLP 4(Brake Flap)
136 ＜Model Menu (Airplane/Glider Functions) ＞Reference FMT-03 is equipped with a stick of multi-copter exclusive use. Therefore it's unsuitable for use of an airplane, a glider and a helicopter.S1●SelectthefunctionnameandreturntotheprecedingscreenbypushingtheRTNbuttonorpushingtheHome/Exitbutton.<Editdial>AIRBRAKE [Correspondingmodeltype]:Airplane,generalThis function is used when an air brake is necessary when landing or diving, etc.The preset elevators and flaps (camber flap, brake flap) offset amount can be activated by a switch.The offset amount of the aileron, elevator, and flap servos can be adjusted as needed. Also the speed of the aileron, elevator, and ap servos can be adjusted. (IN side/OUT side) A delay can be set for each condition, and a Cut switch which will turn OFF the delay can be chosen. Trim amounts can be fine-tuned by setting a VR You can also set the Auto Mode, which will link Airbrake to a stick, switch, or dial. A separate stick switch or dial can also be set as the ON/OFF switch.Setting example for F3A and other aperon specications(When2aileronsmodeltypeselected)Offsetrate: AIL:[-35~-45%],AIL2:[-35~-45%],ELE:[+5~7%]Note: The input numerics are examples. Adjust the travel to match the aircraft.Modesetting: ACT:[ON] Group:[Single] Switch:[SW-C] Mode:[Manual]●WhenanetuningVRissetonthenextpage,theailerons',aps',andelevators'trimratescanbeadjusted. MovethecursortothecorrespondingsettingitemandpushtheRTNbuttontoswitchtothedatainputmode.Adjusttheratewiththeeditdial. PushtheRTNbuttontoendadjustmentandreturntothecursormovemode.●Theailerons,aps,andelevatorsoffsetratecanbeadjusted. MovethecursortothecorrespondingsettingitemandpushtheRTNbuttontoswitchtothedatainputmode.Adjusttheratewiththeeditdial. PushtheRTNbuttontoendadjustmentandreturntothecursormovemode.(Currently selected condition name)●Select[AIRBRAKE]atthemodelmenuandcallthesetupscreenshownbelowbypushingtheRTNbutton.*The display screen is an example. The actual screen depends on the model type.Scrolling●Movingcursor●Adjustingvalue●PushtheS1buttontocallnextpage.
137＜Model Menu (Airplane/Glider Functions) ＞Reference FMT-03 is equipped with a stick of multi-copter exclusive use. Therefore it's unsuitable for use of an airplane, a glider and a helicopter.●Whenusingthisfunction,movethecursortothe[ACT/INH]itemandturntheeditdialtotheleftandpushtheRTNbutton.(ONisdisplayed.)●Group/singlemodeswitching(For more information, see the description at the back of this manual.)●WhenusingafinetuningVR,move thecursortothissettingitemandpresstheEDITbuttontocalltheselectionscreen. SelecttheVRandpushtheRTNbutton.●Conditiondelaysetting(foradescriptionofthesettingmethod,seethedescriptionatthebackofthismanual)andcutswitchsetting.●Ailerons,flaps,anelevatorsservospeedsetting(For a description of the setting method, see the description at the back of this manual.)●Manual/AutomodeselectionManual:SwitchesthefunctionON/OFFbyswitchAuto:Trimmixfunctioncallcanbelinkedtoastick,etc.Astickswitch,etc.separatefromthefunctionON/OFFswitchisset.AIL 3(Chip Aileron) AIL 4(Chip Aileron)AIL1(Main Aileron) AIL 2(Main Aileron)FLP 2(Camber Flap)FLP 1(Camber Flap)ELEVATOR ELEVATOR 2V-TAILELEVATOR ELEVATOR 2AILVATORFLP 3(Brake Flap) FLP 4(Brake Flap)
138 ＜Model Menu (Airplane/Glider Functions) ＞Reference FMT-03 is equipped with a stick of multi-copter exclusive use. Therefore it's unsuitable for use of an airplane, a glider and a helicopter.S1●SelectthefunctionnameandreturntotheprecedingscreenbypushingtheRTNbuttonorpushingtheHome/Exitbutton.<Editdial>GYRO [Correspondingmodeltype]:Airplane/glider,generalThis function is used when a GYA Series gyro is used to stabilize the aircraft's attitude. The sensitivity and operation mode (Normal mode/GY mode) can be switched with a switch.●Threerates(Rate1/Rate2/Rate3)canbeswitched.●Upto3axes(Gyro/Gyro2/Gyro3)canbesimultaneouslycontrolled.*Initial setting does not assign a sensitivity channel. Use the Function menu of the Linkage Menu to assign the sensitivity channel (Gyro/Gyro2/Gyro3) used to a vacant channel beforehand. Set [Control] and [Trim] other than Function to [--].●Theoperationmode(AVCS/NOR)andsensitivityofthe3axiscontrolledbyGyro/Gyro2/Gyro3canbeset.●Group/singlemodeswitching(For more information, see the description at the back of this manual.)●Threerates(Rate1/Rate2/Rate3)canbeused. Movethecursortothe[RATE]itemandpushtheRTNbuttontoswitchtothedatainputmode.Adjusttheratebyscrollingtheeditdial.●Whenusingthisfunction,movethecursortothe[ACT]itemandpushtheRTNbuttontoswitchtothedatainputmode.TurntheeditdialtotheleftandpushtheRTNbutton.●WhenaFutabaGYAgyroisused,when[GY]typeisselected,thesensitivitysetvalueisdirectlyreadinboththeAVCSandNORMmodes.●Whensettingaswitch,movethecursortotheSWITCHitemandpresstheEDITbuttontocalltheselectionscreen,andthenselecttheswitchandsetitsONdirection. (Foradescriptionoftheswitchselectionmethod,seethedescriptionattheendofthismanual.)(Currently selected condition name)●Select[GYRO]atthemodelmenuandcallthesetupscreenshownbelowbypushingthe RTNbutton.Scrolling●Movingcursor●Selectingmode●Adjustingvalue●PushtheS1buttontocallnextpage.
139＜Model Menu (Airplane/Glider Functions) ＞Reference FMT-03 is equipped with a stick of multi-copter exclusive use. Therefore it's unsuitable for use of an airplane, a glider and a helicopter.(Example) Setting three axis using a GYA440(2) and GYA441●Wingtype:Aileron2servosmountedfuselageselected●Set5CH → GYRO(GYA441AIL),7CH → GYRO2(GYA441ELE),8CH → GYRO3(GYA440RUD),Control and Trim → NULL :attheFunctionmenuoftheLinkagemenu.●GYROsettingoftheModelmenu.*Set so that Rate 1 is turned on at the back position of switch E and Rate 3 is turned ON at the front position. Since switch E is turned OFF at the center, Rate 2 remains [INH].Rudder servoElevator servoAileron servoFMR-01GYA440GYA441GYA440GAIN 0％AVCSNORMALWhen AVCS is used we recommend that the sensitivity CH be set to the 3-position.Rate ACT Type Switch GYRO GYRO ２ GYRO ３1 OFF/ON GY SE AVCS : 60% AVCS : 60% AVCS : 60%2 INH3 ON/OFF GY SE NORM : 60% NORM : 60% NORM : 60%
140 ＜Model Menu (Airplane/Glider Functions) ＞Reference FMT-03 is equipped with a stick of multi-copter exclusive use. Therefore it's unsuitable for use of an airplane, a glider and a helicopter.S1●SelectthefunctionnameandreturntotheprecedingscreenbypushingtheRTNbuttonorpushingtheHome/Exitbutton.<Editdial>ELEVATOR(RUDDER 2) RUDDER(ELEVATOR 2)V-TAIL [Correspondingmodeltype]:Airplane/glider,V-tailThis function let’s you adjust for left and right rudder angle changes at elevator and rudder operation of a V-tail airplane.V-tail is when 2 servos are used together to control rudder movement as elevators. In addition to each rudder side moving up and down together, each side moves in opposite directions when moving as elevators. On a V-tail, this is also known as a ruddervator, as they can serve the same purpose.(Rudderfunction) LeftandrighttraveladjustmentatCH1andCH2rudderoperation●Group/singlemodeswitching(For more information, see the description at the back of this manual.)(Elevatorfunction) UpanddowntraveladjustmentatCH1andCH2elevatoroperation(Currently selected condition name)●Select[V-TAIL]atthemodelmenuandcallthesetupscreenshownbelowbypushingtheRTNbutton.●Traveladjustment MovethecursortotheitemyouwanttoadjustandpushtheRTNbuttontoswitchtothedatainputmode. Adjusttheratebyscrollingtheeditdial. PushtheRTNbuttontoendadjustmentandreturntothecursormovemode.*If the mixing direction is reversed by the linkage, adjustments can be made by changing the mixing rate polarity (+ or -).*If a large value of travel is specied, when the sticks are moved at the same time, the controls may bind or run out of travel. Decrease the travel until no binding occurs.Scrolling●Movingcursor●Selectingmode●Adjustingvalue
141＜Model Menu (Airplane/Glider Functions) ＞Reference FMT-03 is equipped with a stick of multi-copter exclusive use. Therefore it's unsuitable for use of an airplane, a glider and a helicopter.S1●SelectthefunctionnameandreturntotheprecedingscreenbypushingtheRTNbuttonorpushingtheHome/Exitbutton.<Editdial>ELEVATOR ELEVATOR 2(AILERON 5) (AILERON 6)AILEVATOR [Correspondingmodeltype]:Airplane/glider,V-Tail (Effective only when 2 servos used at the elevators)This function improves the operating performance of the roll axis by operating the elevators as ailerons.Ailevator is where each elevator in a standard (conventional) or v-tail moves independently, like ailerons on a wing. In addition to each elevator side moving up and down together, each side moves in opposite directions when moving as an ailevator. On a V-tail, this is also known as a ruddervator, as they can serve the same purpose. Typically, both ailevator and ailerons are coupled together to maximize roll performance, especially on larger wingspan planes.Note:SelectailevatorastheModeltypeattheModeltypescreen.Thischangestheoutputchannel.ChecktheFunctionmenu.(Aileronfunction)●Whentheelevatorsareusedasailerons,ailerontraveloftheleftandrightelevatorscanbeadjusted.(Elevatorfunction)●Theupanddownrateoftheleftandrightelevatorswhentheelevatorstickismanipulatedcanbeindividuallyadjusted.●Group/singlemodeswitching(For more information, see the description at the back of this manual.)(Currently selected condition name)●Select[AILEVATOR]atthemodelmenuandcallthesetupscreenshownbelowbypushingtheRTNbutton.●Traveladjustment MovethecursortotheitemyouwanttoadjustandpushtheRTNbuttontoswitchtothedatainputmode. Adjusttheratebyscrollingtheeditdial. PushtheRTNbuttontoendadjustmentandreturntothecursormovemode.*If the mixing direction is reversed by the linkage, adjustments can be made by changing the mixing rate polarity (+ or -).*If a large value of travel is specied, when the sticks are moved at the same time, the controls may bind or run out of travel. Decrease the travel until no binding occurs.Scrolling●Movingcursor●Selectingmode●Adjustingvalue
142 ＜Model Menu (Airplane/Glider Functions) ＞Reference FMT-03 is equipped with a stick of multi-copter exclusive use. Therefore it's unsuitable for use of an airplane, a glider and a helicopter.S1●SelectthefunctionnameandreturntotheprecedingscreenbypushingtheRTNbuttonorpushingtheHome/Exitbutton.<Editdial>RUDDER 1Wingletat Flying wing( )RUDDER 2Wingletat Flying wing( )WINGLET [Correspondingmodeltype]:Airplane/glider,wingletThis function adjusts the left and right rudder angles of airplanes with winglets.Winglets are used to improve the efficiency of aircraft lowering the lift-induced drag caused by wingtip vortices. The winglet is a vertical or angled extension at the tips of each wing. Winglets work by increasing the effective aspect ratio wing without adding greatly to the structural stress and hence necessary weight of its structure - an extension of wing span would also permit lowering of induced drag, though it would cause parasitic drag and would require boosting the strength of the wing and hence its weight - there would come a point at which no overall useful saving would be made. A winglet helps to solve this by effectively increasing the aspect ratio without adding to the span of the wing.(Rudder1/2)●Thetravelatrudderstickleftandrightoperationcanbeindividuallyset.●Group/singlemodeswitching(For more information, see the description at the back of this manual.)(Currently selected condition name)●Select[WINGLET]atthemodelmenuandcallthesetupscreenshownbelowbypushingtheRTNbutton.●Traveladjustment MovethecursortotheitemyouwanttoadjustandpushtheRTNbuttontoswitchtothedatainputmode. Adjusttheratebyscrollingtheeditdial. PushtheRTNbuttontoendadjustmentandreturntothecursormovemode.*If the mixing direction is reversed by the linkage, adjustments can be made by changing the mixing rate polarity (+ or -).Scrolling●Movingcursor●Selectingmode●Adjustingvalue
143＜Model Menu (Airplane/Glider Functions) ＞Reference FMT-03 is equipped with a stick of multi-copter exclusive use. Therefore it's unsuitable for use of an airplane, a glider and a helicopter.S1●SelectthefunctionnameandreturntotheprecedingscreenbypushingtheRTNbuttonorpushingtheHome/Exitbutton.<Editdial>MOTOR [Correspondingmodeltype]:EPglider,generalThis function lets you set the operation speed when the motor of a F5B or other EP glider is started by switch. The operation speed can be set in 2 ranges of slow speed flight and high speed ight (Speed 1/Speed 2). This function can also be operated as a safety function by setting 2 switches.●Theinsideandoutsideoperatingspeedscanbeadjustedindependentlyin2ranges(Speed1/Speed2).●Theboundarybetweenthe2rangescanbeset.(Fromspeed1tospeed2)●Thesetoperationspeedoperationcanbeactivatedatinitialoperationonly.(1timeoperation)However,operationcanberepeated●MovethecursorbysetswitchorVR.bysettingtheswitchtoOFFbeforeoperationisnished.Whenyouwanttoreset1timeoperation,settheACT/INHitemto[INH]andthenresetitto[ON].●Themotor(CH3)iscontrolledbySW-G.(Initialsetting)Whenchangingtheswitchorstickwhichcontrolsthemotor,rstchangeFunctionoftheLinkageMenu.Note: When using this function, always check initial operation with the propeller removed.●Whenusingthisfunction,movethecursortothe[ACT/INH]itemandpushtheRTNbuttontoswitchtothedatainputmode.Turntheeditdialtothe leftandpushtheRTNbutton.●Whenyouwanttosetthe"Onetimemode",movethecursortothe[ONETIME]itemandturntheeditdialtotheleftandpushtheRTNbutton.●Speed1to2 Thespeed1andspeed2regionboundarycanbechanged,●Operationspeedadjustment Thespeedwhenspeed1andspeed2areON(In)andOFF(Out)canbeadjusted.●Whenusingthisfunction,movethecursortothe[ACT/INH]itemandpushtheRTNbuttontoswitchtothedatainputmode.TurntheeditdialtotheleftandpushtheRTNbutton.●Group/singlemodeswitching (Formoreinformation,seethedescriptionatthebackofthismanual.)●Switch AswitchthatturnsthefunctionitselfON/OFFcanbeselected.●Motoroffposition PresstheEDITbuttonfor1secondwhen[SW-G]isinthemotorOFFpositionyouwanttoset.Thedirectionofthemotorswitchismemorized.ThescreengraphdisplayOFFdirectionalsochanges.Notes●FirstdecidethemotorOFFdirection,andthensetthespeed.WhenyouwanttoresetthemotorOFFdirection,alsoresetthespeed.●WerecommendthatmotorOFFbesetincombinationwithF/S.●SetthebasicoperationdirectionwiththereversefunctiontomatchtheESCused.●AlwayssetthemotorOFFposition.(Currently selected condition name)●Select[MOTOR]atthemodelmenuandcallthesetupscreenshownbelowbypushingthe RTNbutton.Scrolling●Movingcursor●Selectingmode●Adjustingvalue●PushtheS1buttontocallnextpage.
144 ＜Model Menu (Airplane/Glider Functions) ＞Reference FMT-03 is equipped with a stick of multi-copter exclusive use. Therefore it's unsuitable for use of an airplane, a glider and a helicopter.S1●SelectthefunctionnameandreturntotheprecedingscreenbypushingtheRTNbuttonorpushingtheHome/Exitbutton.<Editdial>[Correspondingmodeltype]:Glider,generalCONDIT11/3ELEVATOR-50 +50ACCELERATION●1/3Elevatorsetting●2/3Elevator →Cambersetting●3/3Aileron →RuddersettingSetting method●Accelerationratesetting(Rate)●Thereturntimeafteroperation(Dumping)canbeset.●Theoperationpointataccelerationanddecelerationcanbeset.Whenanoperationpointisexceeded,accelerationisperformed.(Currently selected condition name)●Select[ACCELERATION]atthemodelmenuandcallthesetupscreenshownbelowbypushingtheRTNbutton.●Actposition●CurrentpositionAcceleration setting can be performed at elevator, ELE to Camber and AIL to RUD.(Glider and EP glider only) ●Thissettingisdividedintoelevatorsettingandcambersetting.Thesettingmethodisthesame.●CambersettingsetstheaccelerationfunctionforELEtocambermixing.SettingisnotperformedwhenELEtocambermixingisINH.●Theaccelerationfunctioncanbesetforboththeupsideanddownside.●FunctionON/OFFswitchsettingisperformedforAILtoRUDsettingonly.●AILtoRUDsettingisaccelerationfunctionsettingforAILtoRUDmixing.ItisnotperformedwhenAILtoRUDmixingisINH.CONDIT12/3-50 +50CONDIT13/3-50 +50RUDScrolling●Movingcursor●Selectingmode●AdjustingvalueNote:Whenusingtheaccelerationfunction,sincetheservostrokeislarge,makeyoursettingssothereisnobindingofyourlinkage.●PushtheS1buttontocallnextpage.
145＜Model Menu (Airplane/Glider Functions) ＞Reference FMT-03 is equipped with a stick of multi-copter exclusive use. Therefore it's unsuitable for use of an airplane, a glider and a helicopter.S1●SelectthefunctionnameandreturntotheprecedingscreenbypushingtheRTNbuttonorpushingtheHome/Exitbutton.<Editdial>RUD to ELE [Correspondingmodeltype]:Airplane,generalThis function is used when you want to mix elevator operation with rudder operation. It is used to correct undesirable tendencies when rudder is applied in roll maneuvers, knife edge, etc. of stunt planes.●Amixingcurvecanbeset.●MixingduringightcanbeturnedON/OFFbysettingaswitch.(AlwaysONat[--]setting)●Linkcanbeset:Linksthismixingtoothermixings.●Themixingratecanbene-tunedbysettingaVR.(Finetuning)Setting method●MovethecursortotheACT/INHitemandpushtheRTNbuttontoswitchtothedatainputmode.TurntheeditdialtotheleftandpushtheRTNbutton.(ONisdisplayed.)●Whensettingaswitch,movethecursortothe[--]itemoftheswitchandpushtheRTNbuttontocalltheselectionscreen,andthenselecttheswitchandsetitsONdirection.(AlwaysONat"--"setting) (Foradescriptionoftheswitchselectionmethod,seethedescriptionatthebackofthismanual.)●WhensettingaVR,movethecursortotheFineTuning"--"itemandpushtheRTNbuttontocalltheselectionscreen,andthenselecttheVR.Thenetuningratecanbeset. TheVRoperationmodecanalsobeset.●Mixingcurvesetting*For a description of the curve setting method, see the description at the back of this manual.●Left/rightoveralladjustmentatrateAandrateB(Currently selected condition name)●Select[RUDtoELE]atthemodelmenuandcallthesetupscreenshownbelowbypushingtheRTNbutton.●Group/singlemodeswitching(For more information, refer to the description at the back of this manual.)*The display screen is an example. The actual screen depends on the model type.●FinetuningVRsetting●Adjustmentrate●Operationmode[FinetuningVRoperationmode][LIN.] Mixingrate0%atcenterofVR.WhentheVRisturnedclockwiseandcounterclockwise,themixingrateincreasesanddecreases,respectively.[ATL+]Mixingrate0%atleftendofVR.WhentheVRisturned,themixingrateincreases.[ATL-] Mixingrate0%at rightendofVR.WhentheVRisturned,themixingrateincreases.[SYM.]WhentheVRisturnedtotheleftorrightoftheneutralposition,themixingrateincreases. (ForadescriptionofthenetuningVRsettingmethod,seethedescriptionatthebackofthismanual.)●WhensettingLink,movethecursortotheLinkitemandpushtheRTNbuttontoswitchtothedatainputmode.SetittoON.Scrolling●Movingcursor●Selectingmode●Adjustingvalue●PushtheS1buttontocallnextpage.
146 ＜Model Menu (Airplane/Glider Functions) ＞Reference FMT-03 is equipped with a stick of multi-copter exclusive use. Therefore it's unsuitable for use of an airplane, a glider and a helicopter.S1●SelectthefunctionnameandreturntotheprecedingscreenbypushingtheRTNbuttonorpushingtheHome/Exitbutton.<Editdial>SNAP ROLL [Correspondingmodeltype]:Airplane,generalThis function selects the switch and rate adjustment of each rudder, (ailerons, elevators, or aps) when a snap roll is performed.●Foursnaprolldirectionscanbeset.(Right/up,right/down,left/up,left/down)●Operationmode:When[Master]modeisselected,theSnapRollfunctionisturnedON/OFFbymasterswitchinthestateinwhichthedirectionswitchwasswitchedtothedirectioninwhichyouwanttosnaproll.When[Single]modeisselected,snaprollineachdirectioncanbeexecutedbymeansofindependentswitches.●Asafetyswitchcanbeset.Asasafetymeasure,theswitchcanbesetsothatsnaprollisnotexecutedwhen,forinstance,thelandinggearislowered,eveniftheswitchisturnedonaccidentally.ThesnaprollswitchisactivatedonlywhenthesafetyswitchisON.●Theoperationspeedoftheaileron,elevator,andapservoscanbeadjustedforeachsnaprolldirection.(Inside/outside)(Example) Setting example for F3A●Mode:[Master]●SafetySW:[SW-G](Safetymeasure)●MasterSW:[SW-H](Mainswitchforexecutingsnaproll)●Directionswitches:*The snap roll up side left and right and down side left and right direction switches are selected here.Right/Up:OFF[SW-D]Right/Down:OFF[SW-D]Left/Up:OFF[SW-A]Left/Down:OFF[SW-A]●SpeedadjustmentTheoperationspeedofeachcontrolsurfacewhenthesnapswitchisONcanbechangedandsnaprollexecutedbystickwhilethereisswitchoperationcanbeperformed.●Rateadjustment1.Movethecursortotheitemyouwantto adjust andpushtheRTNbuttontoswitchtothedatainputmode.2.Adjustratebyscrollingtheeditdial.3.PushtheRTNbuttontoendadjustmentandreturntothecursormovemode.●Group/singlemodeswitching(For more information, see the description at the back of this manual.)●Directionswitches●Adjustmentoftheservospeedofeachrudder(For a description of the setting method, see the description at the back of this manual.)(Currently selected condition name)●Select[SNAPROLL]atthemodelmenuandcallthesetupscreenshownbelowbypushingtheRTNbutton.Scrolling●Movingcursor●Selectingmode●Adjustingvalue●PushtheS1buttontocallnextpage.
147＜Functions of Model Menu (Helicopter Functions) ＞Reference FMT-03 is equipped with a stick of multi-copter exclusive use. Therefore it's unsuitable for use of an airplane, a glider and a helicopter.S1●SelectthefunctionnameandreturntotheprecedingscreenbypushingtheRTNbuttonorpushingtheHome/Exitbutton.<Editdial>MODEL MENU (HELICOPTER)This section contains information on the commands that apply to helicopters only. For instructions on airplanes and sailplanes, refer to the sections pertaining to those aircraft.Use the Model Type function in the Linkage Menu to select the swash type matched to the fuselage beforehand.Also, add flight conditions at the Condition Select screen if necessary before setting the model data at each function. (Up to 8 conditions can be used)The AFR function, dual rate function and other functions common to all model types, are described in a separate section.Model Menu functions (helicopter) listPIT CURVE: Adjusts response in different ight conditionsTHR CURVE: Throttle curve and hovering trim adjustmentACCELERATION: Allows a brief "overload" in response to sudden throttle and pitch commandsTHR HOLD: Moves the throttle to idle during autorotationSWASH MIX: Compensates for each control responseTHROTTLE MIX: Compensates for power loss when cyclic appliedPIT to NEEDLE: Adjusts response curve in different ight conditionsPIT to RUD: Handles torque changes from pitch angle inputsGYRO: Used to switch gyro sensitivityGOVERNOR: Used to switch RPM of the helicopter’s headTo activate/deactivate Condition Hold:1.Movethecursorto[COND.HOLD].2.Setthethrottlesticklowerthanthe1/3pointandpushtheRTNbuttontoactivate/deactivatetheconditionholdfunction.*Refer to for condition hold function details.*Condition hold operation is displayed.●Selectthe[MODEL]atthehomescreenandcallthemodelmenushownbelowbypushingtheRTNbutton.●UsetheeditdialtoselectthefunctionyouwanttosetandcallthesetupscreenbypushingtheRTNbutton.Scrolling●Movingcursor●PushtheS1buttontocallnextpage.
148 ＜Functions of Model Menu (Helicopter Functions) ＞Reference FMT-03 is equipped with a stick of multi-copter exclusive use. Therefore it's unsuitable for use of an airplane, a glider and a helicopter.CHH-4/H-4XSwashAllOther1Aileron Aileron2Elevator Elevator3Throttle Throttle4Rudder Rudder5Gyro Gyro6Pitch Pitch7GovernorGovernor8Elevator2Governor29GYRO2 GYRO210 GYRO3 GYRO311Governor2 Needle12Needle AUX513AUX414AUX315AUX216AUX1DG1SWDG2CHH-4/H-4XSwashAllOther1Aileron Aileron2Elevator Elevator3Throttle Throttle4Elevator2 Rudder5Pitch Pitch6Gyro Gyro7GovernorGovernor8RudderGovernor29GYRO2 GYRO210 GYRO3 GYRO3DG1SWDG2Helicopter●FASSTest 18CH ●FASSTest 12CHServo connection by Helicopter typeThe FMT-03 transmitter channels are automatically assigned for optimal combination according to the type selected with the Model Type function of the Linkage Menu. The channel assignment (initial setting) for helicopter type is shown below. Connect the receiver and servos to match the type used.*The set channels can be checked at the Function screen of the Linkage Menu. The channel assignments can also be changed. For more information, read the description of the Function menu.
149＜Functions of Model Menu (Helicopter Functions) ＞Reference FMT-03 is equipped with a stick of multi-copter exclusive use. Therefore it's unsuitable for use of an airplane, a glider and a helicopter.S1●SelectthefunctionnameandreturntotheprecedingscreenbypushingtheRTNbuttonorpushingtheHome/Exitbutton.<Editdial>PIT CURVE/PIT TRIMPIT CurveThis function adjusts the pitch operation curve for each ight condition for the optimal ight state relative to movement of the throttle stick.*Up to 17 points can be set for the point curve types. However, when using the 3 points or 5 points specied to create a curve, a simple curve can be created by reducing the number of input points to 3 or 5, and then entering the specied value at the corresponding points that you created a curve.●Pointcurvetypeis9points(initial),butforsimpleuse,4~5pointsaresufcient.Normal curve adjustment●Fornormalcurve,usuallyuse[POINT]typeandcreateabasicpitchcurvecenteredabouthovering.UsethisfunctiontogetherwiththeTHRcurve(normal)functionandadjustthecurvesothatup/downcontrolisbestataconstantenginespeed.Idle up curve adjustment●Forthehighsidepitchcurve,setthemaximumpitchwhichdoesoverloadtheengine.Forthelowsidepitchcurve,createcurvesmatchedtoloop,roll,3D,andotherpurposesandusetheidleupcurvesaccordingtotheperformance.Throttle hold curve adjustment●Thethrottleholdcurveisusedwhenexecutingautorotationdives.Operation precautionsWARNINGWhen actually starting the engine and ying, always set the idle up condition switch to OFF and start the engine in the idling state.(Currently selected condition name)●Select[PITCURVE]atthemodelmenuandcallthesetupscreenshownbelowbypushingtheRTNbutton.●Group/singlemodeswitching(For more information, refer to the description at the back of this manual.)●Mixingcurvesetting*For a description of the curve setting method, see the description at the back of this manual.●Pitchservospeedsetting(For a description of the setting method, see the description at the back of this manual.)●Pitchtrimcopy●Pitchtrimoperatingposition(dottedline)Scrolling●Movingcursor●Selectingmode●Adjustingvalue●PushtheS1buttontocallnextpage.
150 ＜Functions of Model Menu (Helicopter Functions) ＞Reference FMT-03 is equipped with a stick of multi-copter exclusive use. Therefore it's unsuitable for use of an airplane, a glider and a helicopter.Normal Curve Idle-up 1 Curve Idle-up 2 Curve Hold Curve●Pitch Curve (Example)●Group/Singleitem:Whenyoualsowanttoinputthesamesettingcontentsatotherconditions,performsettinginthegroupmode.Inthiscase,thesamecontentsareinputtotheotherconditionssetinthegroupmode.Whenyouwanttoseteachconditionindependently,selectthesinglemode(initialsetting).Otherconditionscanbesetindependently.Setting method●Pittrimcopy(Hover/high/low) Thepitchtrimoperatingpositioncanbecopiedtothepitchcurve. Movethecursortothe[COPY]itemandpushtheRTNbutton. Aftercopying,returnthepitchtrimtothecentertocallthelastoperatingposition.The screens shown below are curves created by entering the pitch rate at low, center, and high side (3 points or 5 points) at each condition. When actually creating a curve, input the rate specied at the fuselage (or the reference value).*For a description of the curve setting method, see the description at the back of this manual.Curve setting examples(Continued on next page)Pitch Trim (Hovering pitch, high pitch, low pitch)The hovering pitch, low pitch, and high pitch trim setup screen can be called from the PIT curve setup screen.●Hoveringpitchtrimsetting●Low/highpitchtrimsetting
151＜Functions of Model Menu (Helicopter Functions) ＞Reference FMT-03 is equipped with a stick of multi-copter exclusive use. Therefore it's unsuitable for use of an airplane, a glider and a helicopter.Hovering pitch trimThe Hovering Pitch trim function trims the pitch near the hovering point. Normally, it is used with the hovering condition. The hovering pitch can be ne tuned for changes in rotor speed accompanying changes in temperature, humidity, and other ight conditions. Adjust the hovering pitch so that rotor speed is constant. This function can be used together with the hovering Throttle Trim function for more delicate operation.Setting method●Whenusingonlythehovering(normal)condition,switchthegroupmodetothesinglemode(initialsetting)beforesetting.●SetthefunctiontoACT[ON].●Selecttheadjustmentknob.●Thetrimoperationmode(Mode:CTRM/NORM)canbeselected. CTRMmode:Maximumamountofchangenearcenterbycentertrimoperation(recommended) NORMmode:Normaltrim(parallelmovementtrim)operation.Theadvantageofusingthismodeisthatthehoveringpitchcanbeadjustedwithoutchangingthecurve.●Trimadjustmentrange(Range)setting Whenthisvalueismadesmall,trimcanonlybeusednearthecenter.●Thetrimratecanbeadjustedandtheoperationdirectioncanbechanged.High Pitch/Low Pitch TrimHigh Pitch/Low Pitch Trim is the pitch servo high side and low side trim function.Setting method●Whensettingtheadjustmentknobscommontoalltheconditions,settheminthegroupmode.●SetthefunctiontoACT(ON).●Selecttheadjustmentknobs.●Thetrimratecanbeadjustedandtheoperationdirectioncanbechanged.●Trimactsashighsideorlowsidetrimwiththecenterasthestandard.
152 ＜Functions of Model Menu (Helicopter Functions) ＞Reference FMT-03 is equipped with a stick of multi-copter exclusive use. Therefore it's unsuitable for use of an airplane, a glider and a helicopter.S1●SelectthefunctionnameandreturntotheprecedingscreenbypushingtheRTNbuttonorpushingtheHome/Exitbutton.<Editdial>THR CURVE/THROTTLE HOVER TRIMTHR CurveThis function adjusts the throttle operation curve for each condition for optimum engine speed to throttle stick movement. Up to 17 curve points can be set for the point curve type, however, when the 5 points and other point data is used, a simple curve can be easily created by reducing the number of input points of the curve to 5 and entering the specified value at the corresponding points.Normal curve adjustment●Normalcurvecreatesabasiccurvecenteredaroundhovering.Useitalongwiththenormalpitchcurveandadjustsothatup/downcontrolataconstantenginespeediseasiest.Idle up curve adjustment●Setaidleupcurvethatmaintainsaconstantspeedatalltimes,evenduringoperationwhichreducesthepitchperformedinight.Createacurvematchedtoloop,roll,3D,orotherpurposesandtheidleupcurveaccordingtotheperformance.Operation precautionsWARNINGWhen actually starting the engine and flying, always set the idle up condition switch to OFF and start the engine in the normal/motor at idle mode.Setting method●Group/singleitem:Whenyouwanttosimultaneouslyenterthesamesettingstootherfunctions,makethesettingsinthegroupmode.Inthiscase,thesamesettingcontentsareenteredtotheallconditions.Whenyouwanttoseteachconditionindependently,makethesettingsafterselectingthesinglemode(Initialsetting).●Throttlehovertrimcopy Thethrottlehover trimoperatingpositioncanbecopiedtothethrottlecurve. Movethecursortothe[COPY]itemandpushtheRTNbutton. Aftercopying,returnthepitchtrimtothecentertocallthelastoperatingposition.(Currently selected condition name)●Select[THRCURVE]atthemodelmenu and callthesetupscreenshownbelowbypushingtheRTNbutton.●Mixingcurvesetting*For a description of the curve setting method, see the description at the back of this manual.●Throttlehovertrimcopy●Throttlehovertrimoperatingposition(dottedline)Scrolling●Movingcursor●Selectingmode●Adjustingvalue●PushtheS1buttontocallnextpage.
153＜Functions of Model Menu (Helicopter Functions) ＞Reference FMT-03 is equipped with a stick of multi-copter exclusive use. Therefore it's unsuitable for use of an airplane, a glider and a helicopter.Normal Curve Idle-up 1 Curve Idle-up 2 Curve●Throttle Curve (Example)The curves shown below are created by using the point curve type and inputting the data of the 5 points 0% (low side), 25%, 50% (center), 75%, 100% (high) side at each condition. They are created by reducing the number points of the line to 5. When actually creating a curve, enter the data specied per the aircraft (or the reference value).*For a description of the curve creation method, see the description at the back of this manual.Curve setting examplesThrottle Hover trimThe Throttle Hover trim setup screen can be called from the THR Curve setup screen.The Throttle Hover function trims the throttle near the hovering point. Normally, use it with hovering conditions. Changes in rotor speed accompanying changes in the temperature, humidity, and other flight conditions can be trimmed. Adjust the throttle so that rotor rotation is most stable. More delicate trimming is also possible by using this function along with the Hover Pitch function.Setting method●Whenusingthehovering(normal)conditiononly,switchthegroupmodetothesinglemode(initialsetting)andmakethesettings.●SetthefunctiontoACT([ON]).●Selecttheadjustmentknob.●Thetrimoperationmode(Mode:CTRM/NORM)canbeselected. CTRMmode:Maximumrateofchangenearcenterbycentertrimoperation(recommended) NORMmode:Normaltrim(horizontalmovementtrim)operation.●Trimadjustmentrange(Range)setting Whenthevalueismadesmall,trimactsonlynearthecenter.●Thetrimratecanbeadjustedandtheoperationdirectioncanbeset.●Setsthedialused.
154 ＜Functions of Model Menu (Helicopter Functions) ＞Reference FMT-03 is equipped with a stick of multi-copter exclusive use. Therefore it's unsuitable for use of an airplane, a glider and a helicopter.Setting method●Activatethefunction1.Select"ACT/INH"andpushtheRTNbutton.2.Scrollingtheeditdialandswitchthedisplayto[INH]or[ACT].3.PushtheRTNbutton.●Group/singlemodeselection.1.Select"GROUP"andpushtheRTNbutton.2.Scrollingtheeditdialandswitchthedisplayto[GROUP]or[SINGLE].3.PushtheRTNbutton.●ON/OFFswitchsetting1.Select"SWITCH"andpushtheRTNbutton.2.Ahardwareselectionscreenisdisplayed.SelectthehardwareandpushtheRTNbutton.●Highsideoperationrangesetting1.Select"HIGH"andpushtheRTNbutton.2.Scrollingtheeditdialandadjustthehighsideoperationrange.3.PushtheRTNbutton.●Lowsideoperationrangesetting1.Select"LOW"andpushtheRTNbutton.2.Scrollingtheeditdialandadjustthelowsideoperationrange.3.PushtheRTNbutton.●Theneutralpositionof"CONTROL"setting1.Select"CENTER"andpushtheRTNbutton.2.Scrollingtheeditdialandadjust theneutralposition.3.PushtheRTNbutton.●Limiteractivationpositionadjustmentcontrolsetting1.Select"CONTROL"andpushtheRTNbutton.2.Ahardwareselectionscreenisdisplayed.SelectthehardwareandpushtheRTNbutton.Throttle Limiter*When the limiter operation range adjustment control is NULL, the throttle limiter function is not activated.This function limits throttle operation to within a certain range. Control which adjusts the operating range during ight can be set. (Effective only when the model type is helicopter.)●OpentheTHRCURVEsetupscreen.PushS1buttontoadvancetonextpageanddisplaypage4.●Throttlelimiteractivationposition●Conditiongroup/single●ThrottlelimiterfunctionACT/INH●MixingON/OFFswitch ●Limiteractivationpositionadjustmentcontrol●Thelimitvalueattheoperationhardwareneutralpositioncanbeadjustedusingthethrottlelimiter.●Highsideoperationrange●Lowsideoperationrange●WhenCENTERisINH.Themotionwiththeequalupperandlowersidesiscarriedout.●WhenCENTERis28%.TheamountofoperationsaboveCONTROLincreases.　ThehighsideofathrottlecanrestricttothisrangebyCONTROL.The neutral position of CONTROLThe neutral position of CONTROL
155＜Functions of Model Menu (Helicopter Functions) ＞Reference FMT-03 is equipped with a stick of multi-copter exclusive use. Therefore it's unsuitable for use of an airplane, a glider and a helicopter.S1●SelectthefunctionnameandreturntotheprecedingscreenbypushingtheRTNbuttonorpushingtheHome/Exitbutton.<Editdial>ACCELERATIONThis function is used to adjust the pitch and the throttle rise characteristic at acceleration/deceleration operation. An acceleration function which temporarily increases the pitch and throttle operations at throttle stick acceleration/deceleration operation can be set.Example of acceleration function use●Whenusedforpitchcontrol,theaccelerationfunctioniseffectivewhenyouwanttoquickentheresponseofthemodelat3Doncollectivepitch. Whenused,highpitchtemporarilyexceedsmaximumpitch,butimmediatelyreturnstomaximumpitch.●Pitchsetting●ThrottlesettingSetting method●Accelerationcanbesetatbothsettingatacceleration(high)andsettingatdeceleration(low). (Theoperationpointisdisplayedonagraph.)●Accelerationratesetting(Rate)●Thereturntimeafteroperation(Dumping)canbeset.●Theoperationpointataccelerationanddecelerationcanbeset.Whenanoperationpointisexceeded,accelerationisperformed.Note:Whenusingtheaccelerationfunction,sincethepitchstrokeislarge,makeyoursettingssothereisnobindingofyourlinkage.(Currently selected condition name)●Select[ACCELERATION]atthemodelmenuandcallthesetupscreenshownbelowbypushingtheRTNbutton.●Actposition●CurrentpositionScrolling●Movingcursor●Selectingmode●Adjustingvalue●PushtheS1buttontocallnextpage.
156 ＜Functions of Model Menu (Helicopter Functions) ＞Reference FMT-03 is equipped with a stick of multi-copter exclusive use. Therefore it's unsuitable for use of an airplane, a glider and a helicopter.S1●SelectthefunctionnameandreturntotheprecedingscreenbypushingtheRTNbuttonorpushingtheHome/Exitbutton.<Editdial>THR HOLDThis function sets the throttle cut position for auto rotation. The throttle position can also be set to an idling position. Setting of these 2 positions can be selected by a switch. This allows use for switching during training.Example of use●Sincethrottleholdhas2modes(Cut)and(Idle),usingitintheIdlingmodeduringtrainingandinthe Cutmodewhenstoppingtheengine.Note:WhenthrottleholdissettoONinthenormalcondition,throttleholdactsandthethrottleservoisdeactivated.AlwayssetthrottleholdtoONintheholdcondition.●Settotheenginestopposition.●Settotheidlingposition.Setting method●Operationmodeselection Manualmode(MANUAL):Thethrottleholdfunctionisoperatedbyswitchoperationonly. Automode(AUTO):Thethrottleholdfunctionoperationislinkedtothethrottlestickposition. Autopositionsetting:Whentheautomodeisselected,thethrottleposition(autoposition)canbeselected.MovethethrottlesticktothepositionyouwanttosetandpushtheRTNbutton.(Autopositionisdisplayed.)●Holdpositionadjustment ThrottleHold(Cut)setsthethrottlecutposition.Adjustitsothatthecarburetorisfullclose. ThrottleHold(Idle):Makethisadjustmenttomaintainidling.Adjustmentscanbemadebasedonthethrottlecurveidleposition.●Thethrottleservooperatingspeedcanbeadjusted.(Speed)●Throttlecutortrainingfunctioncanbeswitchedbyholdfunctionselectorswitch.Operation precautionsWARNINGWhen starting the engine, conrm that the idle up condition and throttle hold condition are OFF.(Currently selected condition name)●Select[THRHOLD]atthemodelmenuandcallthesetupscreenshownbelowbypushingtheRTNbutton.●Holdposition●CurrentpositionScrolling●Movingcursor●Selectingmode●Adjustingvalue●PushtheS1buttontocallnextpage.
157＜Functions of Model Menu (Helicopter Functions) ＞Reference FMT-03 is equipped with a stick of multi-copter exclusive use. Therefore it's unsuitable for use of an airplane, a glider and a helicopter.S1●SelectthefunctionnameandreturntotheprecedingscreenbypushingtheRTNbuttonorpushingtheHome/Exitbutton.<Editdial>SWASH MIXThe swash mix function is used to correct the swash plate in the aileron (roll) direction and elevator (cyclic pitch) corresponding to each operation of each condition.Adjustment by independent curve for aileron, elevator, and pitch operations is possible. The operation can be smoothly adjusted by calling up the “Curve setup” screen by pushing the EDIT button with moving the cursor to the mixing item that corresponds to the mixing and direction which needs correction.Example of use●Asanexample,useswashmixingtocorrectundesirabletendenciesintherolldirection●ForaconditionwhichusesAILtoELE,setthisfunctiontoON.Whenraisingthenoseatarightroll,whentheRateBsideisinputandtherightaileronisoperated,theelevatormovestothedownside.TunebyadjustingtheRate.Forrightroll,adjusttotherateAside.Setting method●Whenusingthisfunction,movethecursortothe[ACT]itemandpushtheRTNbuttontoswitchtothedatainputmode.TurntheeditdialtotheleftandpushtheRTNbutton.(ONisdisplayed.)●Whenyouwanttosetthesamecontentsatotherconditions,selectthegroupmode.Whenyouwanttosettheselectedconditiononly,selectthesinglemode(initialsetting).●Thecorrectionratecanbesetbycurve.● Aswitchcanbeset. When[--]isset,theswashmixingfunctionisoperatedbymerelyselectingthecondition. Whensettingan[ON]/[OFF]switch,movethecursortothe[--]itemandpushtheRTNbuttontocalltheselectionscreenandsettheswitchanditsONposition.(Currently selected condition name)●Select[SWASHMIX]atthemodelmenuandcallthesetupscreenshownbelowbypushingtheRTNbutton.●Group/singlemodeswitching(For more information, refer to the description at the back of this manual.)●Mixingcurvesetting*For a description of the curve setting method, see the description at the back of this manual.Scrolling●Movingcursor●Selectingmode●PushtheS1buttontocallnextpage.
158 ＜Functions of Model Menu (Helicopter Functions) ＞Reference FMT-03 is equipped with a stick of multi-copter exclusive use. Therefore it's unsuitable for use of an airplane, a glider and a helicopter.S1●SelectthefunctionnameandreturntotheprecedingscreenbypushingtheRTNbuttonorpushingtheHome/Exitbutton.<Editdial>THROTTLE MIXThis function corrects slowing of engine speed caused by swash plate operation during aileron or elevator operation. The method of applying clockwise or counterclockwise torque when pirouetting can also be corrected.An acceleration function which temporarily increases the throttle side correction rate relative to rapid stick operation can also be set.Setting example●AILtoTHRappliesaloadtotheengineandcorrectsslowingoftheenginespeedwhentheaileronstickwasoperated.EngineracingcanbeadjustedindependentlyattherightaileronandleftaileronbyRatesAandB.Setting method●Whenusingthisfunction,movethecursortothe[ACT]itemandpushtheRTNbuttontoswitchtothedatainputmode.TurntheeditdialtotheleftandpushtheRTNbutton.(ONisdisplayed.)●Whenyouwanttosetthesamecontentsatotherconditions,selectthegroupmode. Whenyouwanttosettheselectedconditiononly,selectthesinglemode(initialsetting).●Thecorrectionratecanbesetbycurve.●Aswitchcanbeset. When[--]isset,theswashmixingfunctionisoperatedbymerelyselectingthecondition. Whensettingan[ON]/[OFF]switch,movethecursortothe[--]itemandpushtheRTNbuttontocalltheselectionscreenandsettheswitchanditsONposition.When correction is necessary, move the cursor to the mixing item corresponding to the mixing that needs correction and push the RTN button to call the curve setup screen, and then correct the slowing.<Acceleration function setting>●Accelerationcanbesetforbothsettings(Left)and(Right)●Accelerationratesetting(Rate)●Thereturntime(Dumping)afteroperationcanbeset.●Theoperationpointwhenthecorrectionrateisincreasedand decreasedcanbesetindependently.Whenanoperationpointisexceeded,accelerationoperationisperformed.(Currently selected condition name)●Select[THROTTLEMIX]atthemodelmenuandcallthesetupscreenshownbelowbypushingtheRTNbutton.●Group/singlemodeswitching(For more information, refer to the description at the back of this manual.)●Mixingcurvesetting*For a description of the curve setting method, see the description at the back of this manual.●AccelerationsettingsScrolling●Movingcursor●Selectingmode●PushtheS1buttontocallnextpage.
159＜Functions of Model Menu (Helicopter Functions) ＞Reference FMT-03 is equipped with a stick of multi-copter exclusive use. Therefore it's unsuitable for use of an airplane, a glider and a helicopter.S1●SelectthefunctionnameandreturntotheprecedingscreenbypushingtheRTNbuttonorpushingtheHome/Exitbutton.<Editdial>PIT to NEEDLE MIXINGThis mixing is used when the engine is equipped with needle control or other fuel-air mixture adjustment. A needle curve can be set.An acceleration function which temporarily increases needle operation at throttle stick Setting method●Whenusingthisfunction,movethecursortothe[ACT]itemandpushtheRTNbuttontoswitchtothedatainputmode.TurntheeditdialtotheleftandpushtheRTNbutton.(ONisdisplayed.)●Whenyouwanttosetthesamecontentsatotherconditions,selectthegroupmode. Whenyouwanttosettheselectedconditiononly,selectthesinglemode(initialsetting).● Aneedlecurvecanbeset.● Aswitchcanbeset. When[--]isset,themixing functionisoperatedbymerelyselectingthecondition. Whensettingan[ON]/[OFF]switch,movethecursortothe[--]itemandpushtheRTNbuttontoswitchtothedatainputmode.PushtheRTNbuttontocalltheselectionscreenandsettheswitchanditsONposition.< Acceleration function setting>●Accelerationcanbesetatbothsettingatacceleration(high)andsettingatdeceleration(low).●Theaccelerationrate(rate)andthereturntimeafteroperation(dumping)canbeset.●Anoperationpoint(actpos)ataccelerationanddecelerationcanbeset.Whenanoperationpointwasexceeded,accelerationoperationisperformed.●Normally,use[POINT]type.●Select[PITtoNEEDLE]atthemodelmenuandcallthesetupscreenshownbelowbypushingtheRTNbutton.(Currently selected condition name)acceleration/deceleration operation can be set. The rise characteristic of the needle servo at acceleration and deceleration operation can be adjusted.●Group/singlemodeswitching(For more information, refer to the description at the back of this manual.)●Mixingcurvesetting*For a description of the curve setting method, see the description at the back of this manual.●AccelerationsettingsScrolling●Movingcursor●Selectingmode●Adjustingvalue●PushtheS1buttontocallnextpage.
160 ＜Functions of Model Menu (Helicopter Functions) ＞Reference FMT-03 is equipped with a stick of multi-copter exclusive use. Therefore it's unsuitable for use of an airplane, a glider and a helicopter.S1●SelectthefunctionnameandreturntotheprecedingscreenbypushingtheRTNbuttonorpushingtheHome/Exitbutton.<Editdial>PIT to RUD MIXING (REVOLUTION MIXING)Use this mix when you want to suppress the reaction torque generated by main rotor pitch and speed changes during pitch operation. Adjust so that the nose does not move in the rudder direction.An acceleration function which temporarily increases the correction rate at throttle stick acceleration/deceleration operation can be set. The mixing rate at acceleration/deceleration can be set.Setting method●Whenusingthisfunction,movethecursortothe[ACT]itemandpushtheRTNbuttontoswitchtothedatainputmode.TurntheeditdialtotheleftandpushtheRTNbutton.(ONisdisplayed.)●Whenyouwanttosetthesamecontentsatotherconditions,selectthegroupmode. Whenyouwanttosettheselectedconditiononly,selectthesinglemode(initialsetting).●Amixingcurveisset.<Normal condition mixing curve> Themixingcurveratestartsfromasmallvalue. Forarotorwithaclockwiseoperationdirection(polarity),whenpitchwasoperatedattheplusside,setsothatmixingisintheclockwisedirection.First,trimathoveringandthenadjusttheneutralposition.1.Adjustmentbetweenslowandhovering Repeatedlyhoverfromtakeoffandlandfromhoveringataconstantratematchedtoyourownrhythm,andadjustthepitchsothenosedoesnotdeectwhenthethrottleisraisedandlowered.2.Throttlehighside(climbinganddivingfromhovering) Repeatclimbinganddivingfromhoveringataconstantratematchedtoyourownrhythmandadjustthepitchsothatthenosedoesnotdeflectwhenthethrottleisraisedandlowered.However, when a GY Series or other heading hold gyro is used, since correction is performed by the gyro, this mix is not used. If this function is used when the gyro operation mode is the AVCS mode, the neutral position will change.<Idle up condition mixing curve> Setthemixing ratesothattherudderdirectionathigh-speedightisstraightahead.Adjust foreachconditionused.<Acceleration function setting>●Accelerationoperationcanbeperformedforbothsettingatacceleration(high)andsettingatdeceleration(low).●Accelerationratesetting(rate)●Thereturntimeafteroperation(dumping)canbeset.●Anoperationpoint(actpos)ataccelerationanddecelerationcanbesetindependently.Whenanoperationpointwasexceeded,accelerationoperationisperformed.●Normally,use[POINT]type.●Select[PITtoRUD]atthemodelmenuandcallthesetupscreenshownbelowbypushingtheRTNbutton.(Currently selected condition name)●AccelerationsettingsScrolling●Movingcursor●Selectingmode●Adjustingvalue●PushtheS1buttontocallnextpage.
161＜Functions of Model Menu (Helicopter Functions) ＞Reference FMT-03 is equipped with a stick of multi-copter exclusive use. Therefore it's unsuitable for use of an airplane, a glider and a helicopter.S1●SelectthefunctionnameandreturntotheprecedingscreenbypushingtheRTNbuttonorpushingtheHome/Exitbutton.<Editdial>GYRO PROGRAMMING / GAIN SENSITIVITYThis function used to adjust gyro sensitivity. The sensitivity and operation mode (Normal mode/AVCS mode) can be set for each condition.The gyro sensitivity can be switched with each condition or the switch. (5 sensitivities)*Compatible with 3 axis gyro (CGY750).Setting method● Whenusingthisfunction,movethecursortothe[ACT]itemandpushtheRTNbuttontoswitchtothedatainputmode.TurntheeditdialtotheleftandpushtheRTNbutton.(ONisdisplayed.)● Whenyouwanttosetthesamecontentsatotherconditions,selectthegroupmode. Whenyouwanttosettheselectedconditiononly,selectthesinglemode(initialsetting).● Threerates canbeswitched foreachcondition.(Rate1/Rate2/Rate3)● AnetuningVRcanbeset.●Select[GYRO]atthemodelmenuandcallthesetupscreenshownbelowbypushingtheRTNbutton.(Currently selected condition name)(Rate No. display)●FinetuningVRsettings●Gyrosensitivityadjustment●Modeselection: [AVCS]/[NORM]●Gyrotypeselection: [GY]/[NORM]Note:Whenusingthe[Gyro2]/[Gyro3]function,assign[Gyro2]/[Gyro3]toanychannelonthefunctionscreen. Alwayssetto[--]both(control)and(trim)forthe[Gyro]functionattheFunctionmenuintheLinkagemenu.●WhentheGYROfunctionbuttonisselected,eachGYROdetailedsettingscreenappears.Scrolling●Movingcursor●Selectingmode●Adjustingvalue●PushtheS1buttontocallnextpage.
162 ＜Functions of Model Menu (Helicopter Functions) ＞Reference FMT-03 is equipped with a stick of multi-copter exclusive use. Therefore it's unsuitable for use of an airplane, a glider and a helicopter.S1●SelectthefunctionnameandreturntotheprecedingscreenbypushingtheRTNbuttonorpushingtheHome/Exitbutton.<Editdial>GOVERNOR PROGRAMMINGWhen using a Futaba governor, this function is used to switch the RPM of the helicopters head. Up to 3 rates can be set for each condition.*The governor is used by connecting the governor speed setting channel to CH7 (initial setting).*When using an independent governor [ON]/[OFF] switch, connect the AUX([ON]/[OFF]) connector of the governor to CH8 (initial setting) and set the switch to CH8 (Governor2) at the Function menu of the Linkage Menu.*When using the Fuel Mixture function, the mixture servo is controlled from the governor. When transmitting the mixture curve data from the transmitter to the governor, the governor AUX (m.trm) connector must be connected to CH8 (initial setting) and governor side setting performed. See the governor instruction manual.Note:Alwaysset(Control)and(Trim)to[--]for[Governor]and[Governor2]oftheFunctionmenuoftheLinkagemenu.●Select[GOVERNOR]atthemodelmenuandcallthesetupscreenshownbelowbypushingtheRTNbutton.(Currently selected condition name)●FinetuningVRsettings●RPMadjustment●Unitdisplayselection: [%]/[rpm]Setting method●Activate the mixing Whenusingthisfunction,movethecursortothe[INH]itemandpushtheRTNbuttontoswitchtothedatainputmode. SelecttheACTmodebyscrollingtheeditdial.*The display blinks. PushtheRTNbuttontoactivatethemixingandreturntothecursormode.(ONisdisplayed.)　WhentheGovernorischangedfromthedefaultinhibited(INH)statetotheactive(ACT)state,theendpointmenuwillbedisplayedanditispossibletoutilizetheendpointsforthisgivencondition.*When the function is set ON/OFF at the governor setup screen, the governor rpm setting channel end point servo travel and limit point are now initialized.*When changed from INH to ACT (ON), the servo travel is initialized to 100 and the limit point is initialized to 155.*When operation is changed to INH at all conditions, the servo travel is initialized to 100 and the limit point is initialized to 135.●RPM adjustment MovethecursortotherateitemandpushtheRTNbuttontoswitchtothedatainputmode. Adjusttherpmbyscrollingtheeditdial. Initialvalue:50%(1500rpm) Adjustmentrange:OFF,0~110%(OFF,700~3500rpm)*When the RTN button is pushed for one second, the sensitivity is reset to the initial value.) PushtheRTNbuttontoreturntothecursormode.●Unit diplay selection MovethecursortotheUNITitemandpushtheRTNbuttontoswitchtothedatainputmode.Selecttheunitbyscrollingtheeditdial. PushtheRTNbuttontochangetheoperationmodeandreturntothecursormode.Scrolling●Movingcursor●Selectingmode●Adjustingvalue●PushtheS1buttontocallnextpage.
163＜Functions of Model Menu (Helicopter Functions) ＞Reference FMT-03 is equipped with a stick of multi-copter exclusive use. Therefore it's unsuitable for use of an airplane, a glider and a helicopter.●Diplay mode selection*When [rpm] mode is selected above setting, the display mode can be selected.* There is no change in the transmitter output even when the "MODE" is changed. Calibration should be performed via the governor.* In order to use the Governor function of the FMT-03, it is necessary to change the settings on the governor for the low side 700 rpm mode.　WhentheMODEoftheGovernorscreen'smodelmenuischanged,thechangeisalsoindicatedon-screen.The chart below indicates the mode percentage and the corresponding RPM. ●Fine tuning VR settings Movethecursortothe[--]itemandpushtheRTNbuttontoaccesstheselectionscreen.Selectthecontrol.*For a description of the switch selection method, see the description at the back of this manual. MovethecursortotherateitemandpushtheRTNbuttontoswitchtothedatainputmode. Adjustthetrimratebyscrollingtheeditdial. Initialvalue:0%(0rpm)main rotor R.P.M. 3900rpm 2700rpm 2100rpm0% 100% 110%main rotor R.P.M. setting channel travel50% : neutral 2500rpm 2000rpm 1500rpm 1000rpm 700rpm3500rpm Adjustmentrange:-20~+20%(-800~+800rpm)*When the RTN button is pushed for one second, the sensitivity is reset to the initial value.) PushtheRTNbuttontoreturntothecursormode.
164 ＜Functions of Model Menu (Helicopter Functions) ＞Reference FMT-03 is equipped with a stick of multi-copter exclusive use. Therefore it's unsuitable for use of an airplane, a glider and a helicopter.COND.HOLD ConditionholdfunctionThis function may be used to x the maximum speed of the engine so that you may adjust flight conditions when the engine is running. An alarm indicates that the function is operating. It will prevent the engine from increasing when adjusting the idle-up settings. While this function is active, the throttle servo position is fixed at the point set from when the function is activated. You must deactivate this function when you are through making adjustments. The system will not allow you to activate/deactivate this function in either of the following states:• Whenanyoftheflightconditionswitchesareon.• Whenthethrottlestickishigherthanthe1/3point.To activate/deactivate condition hold:(Home screen)1.Movethecursorto[CNDHOLD].2.Setthethrottlesticklowerthanthe1/3point.3.PushtheRTNbuttontoactivatetheconditionholdfunction.*When this function is active, "IS ON" appears at the right of the [CND HOLD] display at the left bottom of the screen.(LINKAGE menu/MODEL menu)1.Movethecursorto[COND.HOLD].2.Setthethrottlesticklowerthanthe1/3point.3.PushtheRTNbuttontoactivatetheconditionholdfunction.*Operation is displayed at the bottom of the menu.Function ON: "CND HOLD IS ON" is displayed.Function OFF: "CND HOLD IS OFF" is displayed.
165＜Functions of Model Menu (Helicopter Functions) ＞Reference FMT-03 is equipped with a stick of multi-copter exclusive use. Therefore it's unsuitable for use of an airplane, a glider and a helicopter.S1●SelectthefunctionnameandreturntotheprecedingscreenbypushingtheRTNbuttonorpushingtheHome/Exitbutton.<Editdial>SWASH RINGSwash ring setting procedure*Perform the following settings after using the edit dial to move the cursor to the item you want to set.1.Activatethefunction: Movethecursortothe[ACT/INH]itemandpushtheRTNbuttontoswitchtothedatainputmode. Switchtheblinkingfrom"INH"to"ACT"byturningtheeditdialtotheleftandthenpushtheRTNbutton.2.Ratesetting: Usetheeditdialtomovethecursortothe[RATE]itempushtheRTNbuttontoswitchtothedatainputmode. Usetheeditdialtosettherate. Initialvalue:100%. Adjustmentrange:50%to200%.*Adjust the rate to maximum swash tilt.(When the RTN button is pushed for 1 second, the rate is reset to the initial value.) PushtheRTNbuttontoendadjustmentandreturntothecursormovemode.Limitstheswashplatetraveltowithinaxedrange.(Helicopteronly)This function limits the swash travel to within a fixed range to prevent damaging of the swash linkage by simultaneous operation of the ailerons and elevators. It is effective in 3D aerobatics which use a large travel.● Theoperatingrangedisplayarea: Theverticaldirectionshowstheelevatortravel.Thehorizontaldirectionshowstheailerontravel.●Themarkershowsthestickposition.●Select[SWASHRING]atthelinkagemenuandcallthesetupscreenshownbelowbypushingtheRTNbutton.●Whentheswashringfunctionisactivated,acircleisdisplayedintheoperatingrangedisplayareaandtherateinputboxisdisplayed.Stickoperationislimitedtowithintheareaofthiscircle.Scrolling●Movingcursor●Selectingmode●Adjustingvalue＜Linkage Menu ＞＜Functions of Linkage Menu (Helicopter Functions) ＞
166 ＜Functions of Model Menu (Helicopter Functions) ＞Reference FMT-03 is equipped with a stick of multi-copter exclusive use. Therefore it's unsuitable for use of an airplane, a glider and a helicopter.S1●SelectthefunctionnameandreturntotheprecedingscreenbypushingtheRTNbuttonorpushingtheHome/Exitbutton.<Editdial>SWASH Swashoperationlinkagecorrectionfunction.(helicopteronly,exceptswashtypeH-1)Neutral PointAt your linkages, if the servo horn deviates from a perpendicular position at neutral, the linkage compensation functions in this menu may not compensate effectively. To correct this use the neutral point function. This will move the neutral point of the servos to the actual perpendicular position. However, this adjustment changes only the axis point of the compensation functions in this menu, and does not affect the neutral position of other functions.Swash AFRSwash AFR function reduces/increases/reverses the rate (travel) of the aileron, elevator and collective pitch functions, by adjusting or reversing the motion of all servos involved in that function, only when using that function. *Before making the following settings, use the edit dial to move the cursor to the item you want to set.Neutral point setting procedureThe neutral point becomes the correction standard point.*Adjusting the servo horn so that the neutral point is near the 50% position makes the mixing amount small.1.Neutralpointsetting Movethecursortothe[POINT]itemandholdthepitchoperationsothattheservohornisatarightangletothelinkagerodandpushtheRTNbuttonfor1secondandreadtheneutralposition.*The neutral point can also be displayed by bar graph. Afterreadingtheneutralpoint,usetheothercorrectionfunctionstomakefurtheradjustments.Mixing RateThis compensation mixing is used to correct the tendency of the swash-plate for each control. The following compensation mixing is possible; PIT to AIL, PIT to ELE, AIL to PIT, ELE to AIL, and ELE to PIT (HR3 mode.) It adjusts the swash-plate to operate correctly for each control using the corresponding compensation mixing.Linkage CompensationThis compensation mixing is used to correct the tendency of the swash-plate for pitch control at low pitch and high pitch.Speed CompensationThis function is used to cancel the reaction that is generated by the difference of the operation amount of each servo when the swash-plate moves.Swash AFR setting procedureThe swash AFR function makes adjustments so that the servos travel the specified amount by [AILERON], [ELEVATOR], and [PITCH] operation.1.UsetheeditdialtomovethecursortothefunctionyouwanttoadjustandpushtheRTNbuttontoswitchtothedatainputmode.2.AdjusttheAFRratebyturningtheeditdialtotheleftorright. Initialvalue:+50% Adjustmentrange:-100%~+100%(When the RTN button is pushed for 1 second, the AFR rate is reset to the initial value.) PushtheRTNbuttontoendadjustmentandreturntothecursormovemode.●Select[SWASH]atthelinkagemenuandcallthesetupscreenshownbelowbypushingtheRTNbutton.Scrolling●Movingcursor●Selectingmode●Adjustingvalue＜Functions of Linkage Menu (Helicopter Functions) ＞＜Linkage Menu ＞●PushtheS1buttontocallnextpage.
167＜Functions of Model Menu (Helicopter Functions) ＞Reference FMT-03 is equipped with a stick of multi-copter exclusive use. Therefore it's unsuitable for use of an airplane, a glider and a helicopter.Mixing rate setting procedureThe HR-3 is taken as an example to describe mixing rate setting. Mixing applied in other swash modes is different, but the setting procedure is the same.*Set the throttle stick to the preset neutral point. Adjust the length of the linkage rod so that the swash plate is horizontal at this position.*The sub trim function can be used to make small adjustments.*Adjust so that the pitch curve is a straight line and pitch operation is maximum.*When making the following setting, use the edit dial to move the cursor to the item you want to set and push the RTN button to switch to the data input mode. Push the RTN button to end adjustment and return to the cursor move mode.1.Adjustmentataileronoperation[AILtoPIT] AdjusttheAILtoPITratesothereisnointerferenceintheelevatororpitchdirectionwhentheaileronstickismovedtotheleftandright.*Adjust by turning the edit dial to the left or right.*The left and right sides can be adjusted individually.2.Adjustmentatelevatoroperation[ELEtoAIL]/[ELEtoPIT] AdjusttheELEtoAILandELEtoPITratessothereisnointerferenceintheaileronorpitchdirectionwhentheelevatorstickismovedupanddown.*Adjust by turning the edit dial to the left and right.*The up and down sides can be adjusted individually.3.Adjustmentatpitchoperation[PITtoAIL][PITtoELE] AdjustthePITtoAILandPITtoELEratessothattheswashplatemovestothehorizontalpositionwhenthethrottlestickwasmovedtomaximumslowandfullhigh.*Adjust by turning the edit dial to the left and right.*The slow and high sides can be adjusted individually.Linkage compensation setting procedure*Perform linkage compensation setting after mixing rate setting.*Linkage compensation compensates for interference by aileron operation with the elevator or elevator operation with the aileron at collective pitch control for low pitch and high pitch.*When making the following setting, use the edit dial to move the cursor to the item you want to set and push the RTN button to switch to the data input mode. Push the RTN button to end adjustment and return to the cursor move mode.1.Compensationataileronoperation[AILERON] Setthethrottletothemaximumslowposition.Movetheaileronsticktotheleftandrightandadjusttheaileroncompensationamountsothatinterferenceintheelevatororpitchdirectionatthattimeisminimum.*Adjust the edit dial to the left and right.*The left and right sides can be adjusted individually.*When the interference increases when the compensation amount was increased, make adjustments with the compensation direction [DIR] as "-".2.Compensationatelevatoroperation[ELEVATOR] Adjusttheelevatorcompensationamountsothattheaileronorpitchdirectioninterferencewhentheelevatorstickwasmovedupanddownisminimum.3.Regardingsteps1and2above,performaileronandelevatorcompensationsimilarlyatthefullhighsideofthethrottlestickalso.Speed compensation setting procedure1.Usetheeditdialtomovethecursortothe"SPEEDCOMPENSATION"itemandpushtheRTNbuttontoswitchtothedatainputmode.2.Setthethrottlesticktotheneutralpointposition.Quicklymovetheelevatorstickandadjustthespeedcompensationamount[SPEEDCOMPENSATION]forminimuminterferenceinthepitchdirection.*Adjust by turning the edit dial to the left and right. PushtheRTNbuttontoendadjustmentandreturntothecursormovemode.＜Functions of Linkage Menu (Helicopter Functions) ＞
168 ＜Functions of Model Menu (Helicopter Functions) ＞Reference FMT-03 is equipped with a stick of multi-copter exclusive use. Therefore it's unsuitable for use of an airplane, a glider and a helicopter.FUTABA CORPORATION Phone: +81 475 32 63811080 Yabutsuka, Chosei-mura, Chosei-gun, Chiba-ken, 299-4395, Japan©FUTABA CORPORATION 2017, 03 (1)

Navigation menu