Furuno USA 9ZWRTR103 Transceiver for Radar Sensor DRS4W User Manual

Furuno USA Inc Transceiver for Radar Sensor DRS4W

User Manual

RADAR SENSORDRS4WOPERATOR'S MANUALwww.furuno.comModelTENTATIVE
TENTATIVE
The paper used in this manualis elemental chlorine free.・FURUNO Authorized Distributor/Dealer9-52 Ashihara-cho,Nishinomiya, 662-8580, JAPANA:APR2012.Printed in JapanAll rights reserved.C:APR.10, 2013Pub. No.OME-44730-C(DAMI)FMD-3200/3200BB/3300 0 0 0 1 7 6 1 2 5 1 2TENTATIVEZ1 : MAR. 6, 2014Pub. No. OME-36360-Z1DRS4W
iIMPORTANT NOTICESGeneralHow to discard this productDiscard this product according to local regulations for the disposal of industrial waste. For disposal in the USA, see the homepage of the Electronics Industries Alliance (http://www.eiae.org/) for the correct method of disposal.How to discard a used batterySome FURUNO products have a battery(ies). To see if your product has a battery, see the chapter on Maintenance. Follow the instructions below if a battery is used. Tape the + and - terminals of battery before disposal to prevent fire, heat generation caused by short circuit.In the European UnionThe crossed-out trash can symbol indicates that all types of batteries must not be discarded in standard trash, or at a trash site. Take the used batteries to a battery collection site according to your national legislation and the Batteries Directive 2006/66/EU. In the USAThe Mobius loop symbol (three chasing arrows) indicates that Ni-Cd and lead-acid rechargeable batteries must be recycled. Take the used batteries to a battery collection site according to local laws.In the other countriesThere are no international standards for the battery recycle symbol. The number of symbols can increase when the other countries make their own recycle symbols in the future.• This manual has been authored with simplified grammar, to meet the needs of international users.• The operator of this equipment must read and follow the descriptions in this manual. Wrong oper-ation or maintenance can cancel the warranty or cause injury.• Do not copy any part of this manual without written permission from FURUNO.• If this manual is lost or worn, contact your dealer about replacement.• The contents of this manual and equipment specifications can change without notice.• The example screens (or illustrations) shown in this manual can be different from the screens you see on your display. The screens you see depend on your system configuration and equipment settings.• Save this manual for future reference.• Any modification of the equipment (including software) by persons not authorized by FURUNO will cancel the warranty.Trademark Notices• All brand and product names are trademarks, registered trademarks or service marks of their re-spective holders.• Apple, iPad and iPhone are registered trademarks of Apple, Inc.• App Store is a registered service mark of Apple, Inc.• iOS is a registered trademark of Cisco Systems, Inc.CdPbNi-CdTENTATIVE
ii SAFETY INFORMATION Read these safety instructions before installing or operating the equipment.WARNINGIndicates a potentially hazardous situation which, if not avoided,can result in minor or moderate injury. Warning, Caution Prohibitive ActionCAUTION Mandatory ActionIndicates a potentially hazardous situation which, if not avoided,can result in serious injury or death. Safety Information for the Operator Safety Information for the InstallerWear a safety belt and hard hat when working on the antenna unit.Serious injury or death can result ifsomeone falls from the radar mast.Do not open the equipment.The installation does not require you to open the radar sensor.Be sure the power source is compatible with the voltage rating of the equipment.Connection of an incorrect power source can cause fire or damage the equipment.Turn off the power at the power source before beginning the installation.Fire, electrical shock or serious injury can result if the power is left on or is applied while the equipment is being installed.WARNINGWARNINGELECTRICAL SHOCK HAZARDDo not open the equipment.There are no user servicable parts inside.The radar antenna emits electromag-netic radio frequency (RF) energywhich can be harmful, particularly toyour eyes. Never look directly into the antenna aperture from a close distance while the radar is in operation or expose yourself to the transmittingantenna at a close distance.Distances at which RF radiation levels of100, 50 and 10 W/m2 exist are given in the table below.100 W/m210 W/m2N/A 0.0 mDo not disassemble or modify theequipment.Fire, electrical shock or serious injury canresult.Wear a safety belt and hard hat when working on the antenna unit.Serious injury or death can result ifsomeone falls from the radar mast.NOTICEObserve the following compass safe distance to prevent interference to a magnetic compass.It is recommended that you connect the sensor to a disconnecting device (circuit breaker, etc.) to control the power.Standardcompass1.45 m 0.90 mSteeringcompass50 W/m2N/AUse the proper fuse.Use of a wrong fuse can damage the equipment or cause fire.TENTATIVE
SAFETY INFORMATIONiiiWARNING LABELA warning label is attached to the sensor. Do not remove the label. If the label is missing or damaged, contact a FURUNO agent or dealer about replacement.NOTICEDo not expose the radar sensor to strong water jets.Excessively strong water jets can damage the sensor.Name: Warning Label (2) Type: 03-129-1001-3Code No: 100-236-743TENTATIVE
ivTABLE OF CONTENTSFOREWORD ........................................ v1. OPERATION ................................. 11.1 System Overview ........................11.2 How to Start, Stop the System ....11.3 Transmit, Standby .......................21.4 Display Layout.............................21.5 Touch Screen Operations ...........31.6 Picture Menu ...............................31.7 How to Adjust the Screen Tone ..41.8 How to Select a Display Range...41.9 How to Reduce Rain Clutter........41.10 How to Measure the Bearing and Range to a Target (iPad only) .....41.11 How to Off Center the Display.....51.12 Echo Stretch................................51.13 Palette .........................................51.14 Echo Color ..................................61.15 Picture Format.............................61.16 How to Take a Screenshot ofthe Display ..................................61.17 Settings Menu .............................62. MAINTENANCE, TROUBLESHOOTING...................82.1 Maintenance ...............................82.2 Replacement of Fuse..................82.3 Troubleshooting ..........................92.4 Error Messages...........................92.5 Replacement of Magnetron.........92.6 Self Test....................................103. INSTALLATION ...........................113.1 Equipment List ..........................113.2 Installation Considerations........113.3 How to Install theRadar Sensor............................123.4 How to Set up the Radar Sensor............................153.4.1 How to start the system.....153.4.2 Heading, timingadjustment .........................153.4.3 Range unit .........................173.4.4 Tuning initialization ............173.4.5 Sector blank.......................17APPENDIX 1 MENU TREE............ AP-1APPEDNIX 2 RADIO REGU-LATORY INFORMATION .............. AP-2SPECIFICATIONS ..........................SP-1INDEX ..............................................IN-1TENTATIVE
vFOREWORDA Word to the Owner of the DRS4WCongratulations on your choice of theFURUNO RADAR SENSOR DRS4W.Since 1948, FURUNO Electric Company has enjoyed an enviable reputation for innovative and dependable marine electronics equip-ment. This dedication to excellence is fur-thered by our extensive global network of agents and dealers. This equipment is designed and constructed to meet the rigorous demands of the marine environment. However, no equipment can perform its intended function unless installed, operated and maintained properly. Please carefully read and follow the recommended procedures for installation, operation, and maintenance. We would appreciate hearing from you, the end-user, about whether we are achieving our purposes. Thank you for considering and purchasing FURUNO.Features• Complies with wireless LAN standard IEEE802.11b.• Radar sensor forwards radar echoes to an iPad or iPhone via the 2.4 GHz radio band.• Compatible with the following iOS terminals (iOS 6.1.3, 7.0.4 or higher):• iPhone 5, 5c, 5s• iPad 2, 3, 4, mini• Stylish radome-type radar sensor.• Echoes shown in green or yellow, ormulticolor in red, yellow or green, corre-sponding to strong, medium and weakechoes.• 14 ranges from 0.125 to 24 NM.• Screen tone adjustable to suit lighting con-ditions.• Two iOS terminals can be connected to the radar sensor at the same time.• Echo stretch lengthens echoes in range and/or bearing direction.• Automatic adjustment of sea clutter (ech-oes from waves), gain, noise and interfer-ence.• Off center feature lets you look focus on a specific area ahead of or around your ves-sel without losing track of position.• Self test checks the radar sensor for correct operation.System ConfigurationRADAR SENSORDRS4WPower supply12/24 VDC Wireless LAN (WLAN)2.4 GHz iOS Terminal(iPad, iPhone)AC/DCAdapterTENTATIVE
11. OPERATION1.1 System OverviewThe radar sensor transmits pulses of micro-wave energy that bounce off any object in their path. The object returns a tiny part of the wave's energy to the radar sensor. Radar de-termines the distance to a target by calculat-ing the time difference between the trans-mission of a radar signal and the reception of the reflected echo. The bearing to a target found by the radar is determined by the direc-tion in which the antenna is pointing when it emits an electronic pulse and then receives a returning echo.The radar sensor forwards the returning ech-oes to the iOS terminal (iPhone, iPad), using its wireless LAN module. The radar applica-tion in the iOS terminal displays the radar ech-oes on the terminal’s display and provides controls for adjustment of the radar picture.1.2 How to Start, Stop the SystemPower the radar sensor to acti-vate the system. Open your iPad or iPhone terminal and click the [Marine Radar] application icon (see right figure).The splash screen appears for a few mo-ments, then the application tries to connect to the radar sensor, which normally takes no more than three seconds. If the connection is successful, the [Preheating] display appears.If the connection failed, the window shown right appears. Tap the [Search again] button to try to connect to the radar sensor. If you cannot connect to the radar sensor, check for interfering objects near the sensor and make sure the wireless LAN func-tion is enabled on your terminal.The preheating stage, which warms the mag-netron (the device responsible for transmitting radar pulses), takes approx. 90 seconds. The time remaining until the completion of the pre-heating is counted down at the center of the screen. After the completion of the preheat-ing, the STBY display appears. To deactivate the system, disconnect the ra-dar sensor from the power source.Note: To connect an iOS terminal to another DRS4W, reset the application first. Radar sensoriPhoneiPadWireless LAN2.4 GHzWireless LAN2.4 GHz Splash screenSearching radar sensorPreheatingdisplayRadar sensorcommunciation error!E0002: Please check WLANconnection setup, and power isapplied to radar sensor.Search againTENTATIVE
1. OPERATION21.3 Transmit, StandbyTap the [STBY-TX] icon at the top right corner on the screen to put the radar in standby, transmit state alternately.When you don’t need the radar, set it to stand-by to extend the life of the magnetron.Note: The radar application is set to standby when you switch to another application, or there is no operation for one minute. Howev-er, the picture is continuously updated. The notifications banner, which alerts you to re-ceived mail, etc., works while the radar appli-cation is active.1.4 Display LayoutThe figure below shows all the indications, markers and icons that appear on the iPad radar dis-play. The layout on the iPhone is similar.STBY-TX iconMenu tab*Fixed range ringsDisplay rangeHeading lineRange selection buttonsCursor*Own ship markBearing, range box*Bearing scaleBearing line** Not provided on iPhone.TENTATIVE
1. OPERATION31.5 Touch Screen OperationsThe table below shows all the basic touch screen operations.1.6 Picture MenuThis sensor has three menus: Picture, Color, and Settings.The Picture menu contains the most frequently used radar functions.1. iPad: Tap the Menu tab at the right side of the screen to show the menu.iPhone: Tap anywhere to show the menu.2. Tap the ( ) icon to activate the [Picture] menu.3. Use the page selection buttons ( ) to browse the items of the menu. For exam-ple, select [Sector Blank].4. The [Picture] menu has several types of controls for adjustment.Slider bar with and buttons: Drag the slider bar to adjust the item selected. Use the or button to fine tune the setting.Function buttons: Tap the appropriate button to select the function labeled on the button.5. To close the menu, tap anywhere outside the menu area.Operation Action Operation ActionTap • Open, close menus.• Operate vari-ous buttons.Drag • Move the cur-sor.*• Move slider bar in menus.• Off center the display.Double tap• Cancel off center dis-play.Pinch in,Pinch out• Select display range.Long push(approx. 2 sec.)• Display the cursor.** The iPhone does not have a cursor.Color menu iconPicture menu iconSettings menu iconMenu tab/Slider barItem namePage selection buttonsItem no./Item totalFunction button3 / 3++TENTATIVE
1. OPERATION41.7 How to Adjust the Screen ToneThe screen tone (brightness) can be adjusted to suit lighting conditions. Open the menu then tap the ( ) icon. Drag the slider bar to adjust the screen tone.1.8 How to Select a Display RangeThe range selects how far you want the radar to “see”. The range selected automatically de-termines the range ring interval, the number of range rings and pulse repetition rate. The current range is shown at the top left corner on the screen.R: Display range, FRR: Fixed range ringinterval, NR: Number of fixed range ringsTo select a display range, tap the range selec-tion buttons at the bottom right and left cor-ners. Alternatively, you can pinch in or pinch out within the display area.1.9 How to Reduce Rain ClutterThe antenna picks up rain clutter (rain, snow, or hail) in the same manner as normal targets, as in the right fig-ure. When rain clutter masks targets, use the [Rain] control to reduce the clutter. The higher the setting the greater the reduction of rain clutterTo adjust the rain clutter, open the menu then tap the ( ) icon. Select the [Rain] screen. Tap the [Manual] or [Auto] button. For manual adjustment, drag the slider bar to reduce the rain clutter.1.10 How to Measure the Bearing and Range to a Target (iPad only)The bearing and range from own ship to a tar-get can be measured with the cursor. Long push the screen to show the cursor, which is a cross (+). Drag the cursor to put it on the center of the target. See the bearing and range to the target in the [Bearing/Range] box, which is to the side of the cursor. After several seconds, the cursor is erased from the screen.R 0.125 0.25 0.5 0.75 1FRR 0.0625 0.125 0.125 0.25 0.25NR 2 2 4 3 4R1.5 2 3 46FRR 0.5 0.5 1 1 2NR 3 4 3 4 3R 8 12 16 24FRR 2 3 4 6NR 4 4 4 4Decrease the range(zoom in)Increase the range(zoom out)Manual adjustmentAutomatic adjustment1 / 31 / 3TENTATIVE
1. OPERATION5Note: A slight difference exists between fin-ger position and cursor position in order to see the cursor while dragging it.1.11 How to Off Center the DisplayOwn ship position, or sweep origin, can be displaced manually or automatically to ex-pand the view without switching to a longer range. The maximum amount of shift is 75% of the range in use.To off center the display, drag the own ship mark to the position you want to make the screen center. To return to the normal display, double tap the display area.1.12 Echo StretchOn long ranges, target echoes tend to shrink, making them difficult to see. To enhance tar-get video on long ranges, use the echo stretch feature to lengthen echoes in the bearingand/or range direction.Open the menu then tap the ( ) icon. Select the [Echo Stretch] screen. Select [Low] to lengthen echoes in the bearing direction; [High] to lengthen echoes in both the bearing and range directions.1.13 PaletteThe palette feature changes the color of the background, characters, range rings and heading line to suit the time of day, daytime or nighttime.Open the menu then tap the ( ) icon. Select [Day] or [Night] as appropriate.Bearing,range to cursorCursorNormal display Off centered displayItem ColorDay NightBackground White BlackCharacters Gray RedRings Gray RedHeading line Gray RedEcho Brg dir. Brg dir.Rngdir.Echo stretch OFFEcho stretchLowEcho stretchHigh2 / 3TENTATIVE
1. OPERATION61.14 Echo ColorEchoes can be shown in yellow, green, or multicolor. Multicolor paints each radar echo in a color according to its strength, in red, yel-low or green, corresponding to strong, medi-um and weak echoes. Open the menu then tap the ( ) icon. Select the color desired at [Echo Color].1.15 Picture FormatYou can show the radar picture in landscape or portrait format. Rotate your terminal to change the format.1.16 How to Take a Screenshot of the DisplayYou can take a screenshot of the radar dis-play, and save it to the Photos folder in your terminal. Push the Home and Power buttons together. You should hear the camera shutter sound.1.17 Settings MenuThe [Settings] menu contains items that once preset do not require frequent adjustment. Open the menu then tap the ( ) icon to open the [Settings] menu.Display Settings menu[Full Screen]: Turn the full screen display on or off.[Range Ring]: The range rings are the con-centric circles about own ship position, and they function to provide an estimate of the range to a target. You can turn the rings on or off here.[Own Ship Mark]: The own ship mark is shown at the display center and indicates your current position. You can turn the mark on or off here.(Version no. appears here)Full screen ONFull screen OFFTENTATIVE
1. OPERATION7Initial Settings menu[Units]: Select the unit of range measure-ment, nm or km.[Tune Initialize]: Automatically tune the radar receiver. See the chapter on installation.Installation Settings menuThe items in this menu are mainly intended for the serviceman. See the chapter on installa-tion.Self TestTests the radar sensor and radar application for proper operation. See the chapter on Maintenance.Operation GuideOperator’s guide to the basic functions of this radar.VersionShows the software version no.UnitsTune Initializenm>TENTATIVE
82. MAINTENANCE,TROUBLESHOOTING2.1 MaintenanceRegular maintenance is important for good performance. Check the points mentioned be-low every 3 to 6 months to keep the radar sen-sor in good working order. Observe the safety instructions at the front of this manual when working on the mast.2.2 Replacement of FuseThe 5A fuse (Type: FGBO 250V 5A PBF, Code No.: 000-155-840-10) in the fuse holder on the power cable protects the radar sensor from overcurrent and equipment fault. If you cannot turn on the power, check the fuse to see if it has blown. If the fuse has blown, find the reason before you replace the fuse. If the fuse blows again after the replacement, con-tact your dealer for advice.WARNINGDO NOT OPEN THE SENSOR.Electrical shock hazardThere are no user-serviceable parts inside. Only qualified personnel are allowed to work inside the equipment. Check point ActionCheck fixing bolts for corro-sion and if tightly fastened.Tighten loosened bolts. Replace corroded bolts. Coat new bolts with marinesealant. Check radome for cracks,foreign material.If a crack is found, repair it temporarily with a small amount of sealing com-pound or adhesive. Bring the unit to your dealer for permanent repairs.Foreign material on theradome can cause aconsiderable drop in sensi-tivity. Remove foreignmaterial with a freshwater-moistened cloth. Do not use commercial cleaners to clean the sensor; they can remove paint and markings or deform the plastic.Do not apply paint, anti-corrosive sealant or contact spray to coating or plastic parts.Those items contain organic solvents that can damage coating and plastic parts.NOTICEWARNINGUse the proper fuse.Use of the wrong fuse can damage the equip-ment or cause fire.TENTATIVE
2. MAINTENANCE, TROUBLESHOOTING92.3 TroubleshootingThe table below provides simple trouble-shooting procedures that the user can follow to restore normal operation. If you cannot re-store normal operation, contact your dealer for advice.2.4 Error MessagesError messages are shown to alert you to ra-dar sensor problems. The table below shows the error messages and accompanying mes-sage numbers and check points. These alerts appear in the background; no notification is given.2.5 Replacement of MagnetronThe life expectancy of the magnetron is ap-prox. 5,000 hours (including standby). The ef-fectiveness of the magnetron decreases over time, causing lower-than-normal signal strength and loss of echoes. If you feel the signal strength is low, contact your dealer about replacement of the magnetron.Trouble RemedyThe power cannot be turned on.• Check if the power cable is connected to the power source and the power source is on.• Check the power cable for damage.• Check if the fuse has blown.The power is on but noth-ing appears on thedisplay.Try adjusting the brightness with [Brightness] in the[Settings] menu in your termi-nal, or [Screen Tone] in the ra-dar application.The display freezes.• Restart the application.• Reset your terminal.You cannot connect to the wireless LAN but you can see the host on the terminal.• Switch between standby and transmit.• Restart the application.• Check the WLAN settings in your terminal.• Restart your terminal.Message Message no. andcheck point "No radar sensor found!"E0001: Please check WLANconnection setup, and power is applied to radar sensor."Radar sen-sor communi-cation error!"E0002: Please check WLAN connection setup, and radar sensor condition."Radar sen-sor signalerror!"E0003: Heading pulse ofradar sensor is not detected. Please check radar sensor condition.E0004: Video pulse of radar sensor is not detected. Please check radar sensor condition.Name Type Code no.Magnetron E3571 000-126-646TENTATIVE
2. MAINTENANCE, TROUBLESHOOTING102.6 Self TestThe self test is for use by the service techni-cian to check the equipment. However, the user can do the test to support the service technician.1. Open the menu then tap the ( ) icon.2. Tap [Self Test] to do the self test.The result for [ROM], [RAM], [WLAN Status] and [Antenna Status] is [OK] or [NG] (No Good). If [NG] appears for an item, try the test again. If [NG] appears again, contact your dealer for advice.WLAN=Wireless LANActual value appears in place of “x”.WLAN FW versionWLAN StatusWLAN ChannelWLAN Power15dBm03593929-xx.xx03593930-xx.xx0359313-xxxxxxx-xx172.31.x.xx172.31.x.xxxx-xx-xx-xx-xx-xxxScrollTENTATIVE
113. INSTALLATION3.1 Equipment List3.2 Installation ConsiderationsName Type Code No. Qty RemarksStandard supplyRadar Sensor RSB-126-103 - 1InstallationMaterialsCP03-35800 000-024-974 SelectonePower cable assy., 10 mCP03-35810 000-024-975 Power cable assy., 15 mCP03-35820 000-024-976 Power cable assy., 20 mCP03-35830 000-024-977 Power cable assy., 30 mCP03-35701 001-265-920 1 - Hex bolt*(M10×25), 4 pcs. - Flat washer (M10 SUS304), 4 pcs.- Spring washer (M10 SUS304), 4 pcs.*For use if thickness of platform is6–10 mm.Documents OME-36360 - 1 Operator’s ManualMDC-36360 - 1 C-ROHS listE32-01314 - 1 TemplateE32-01401 - 1 SSID, password informationSpare Parts SP03-17801 001-265-910 1 5A fuse, 2 pcs.Optional supplyRadome Mount OP03-209 001-078-350 1 Mast mounting bracket for sailboatGeneral considerations:• Do not apply paint, anti-corrosive sealant or contact spray to coating or plastic parts. Those items contain solvents that can damage coating and plastic parts.• The radar sensor has no power switch. Therefore, it is recommended that you connect the sensor to a disconnecting device (circuit breaker, etc.) to control the power.Sensor placement:• The radar sensor uses the 2.4 GHz wireless LAN radio band to forward radar echoes to the iOS terminal. Separate the sensor well away from products which also use this band (microwave range, Bluetooth devices, etc.) to prevent mutual interference.• Install the radar sensor on the hardtop, radar arch or on a mast on an appropriate platform. (For sailboats, a “radome mount” is optionally available for fixing the sensor to a mast.) Place the sen-sor where there is a good all-round view with, as far as possible, no part of the ship’s superstruc-ture or rigging intercepting the scanning beam. Any obstruction will cause shadow and blind sectors. Be sure there are no metallic objects near the antenna. See the next page for typical placement on a sailboat and powerboat.• Observe the wireless LAN communication range noted in the illustration on the next page.• In order to reduce the chance of picking up electrical interference, avoid where possible routing the power cable near other electrical equipment onboard. Also, avoid running the cable in parallel with other power cables.• Select a location that does not allow water to accumulate at the base of the sensor.• A magnetic compass will be affected if the radar sensor is too close to the compass. Observe the compass safe distances mentioned on page ii to prevent interference to a magnetic compass.TENTATIVE
3. INSTALLATION123.3 How to Install the Radar SensorDetermine the suitability of the mounting loca-tion BEFORE permanently mounting the sen-sor. Incoming and outgoing signals may overlap one another depending on the shape of the vessel, preventing communication be-tween the terminal and the sensor. Set the sensor on the selected location and connect the sensor to the power source. Turn on the sensor. Open the terminal, turn on the radar application and try to connect the terminal to the sensor (see section 3.4.1 for how to start the system). If the connection is successful, change the range to check if the sensor re-ceives your command. Check that the picture is updated with each sweep. Some trial and error may be necessary to find a suitable loca-tion.Installation on a platform1. Remove the mounting hardware at the bottom of the radar sensor - four each of hex bolts (M10×20), spring washers and flat washers. Save the spring washers and flat washers to use them to fasten theradar sensor to the platform, at step 4. If the thickness of the platform is 5 mm or less, also save the bolts.Radar sensorRadar sensorInstallation on a sailboatRadar sensorRadar sensorInstallation on a powerboat45°60°Weak signalarea30°30°Location and wireless LAN communication rangeTypical installation on a sailboat, power boatStrong signal areaStrong signal areaWeak signalareaStrong signal areaStrong signal areaiPhoneWeak signalareaWeak signalareaWeak signalareaHex boltSpring washerFlat washerSTERNBOWPower cableTENTATIVE
3. INSTALLATION132. Construct a platform (steel or aluminum) referring to the outline drawing and the mounting template. Fasten the platform to the mounting location. The holes in the platform must be parallel with the fore and aft line.3. Put the radar sensor on the platform with the bow mark (U) on sensor aligned with the bow.4. Use hex bolts*, flat washers and spring washers (removed at step 1) to fasten the radar sensor to the platform. The torque for the bolts must be 19.6 to 24.5 N•m.*See the figure below to determine bolt length to use.5. Connect the supplied power cable to the sensor. Observe the guidelines for laying the power cable shown on this page.6. Connect the power cable to the power source. Guidelines for laying the power cable• The connectors must not strike any part of the vessel by wind, etc.• The load applied to the connectors must not be more than its own weight.• If the cable is passed through a mast on a sailboat, be sure the cable does not touch ropes (sheet, halyard, etc.).• Do not fasten the cable to the hull.• The cable must be fixed so no tension is ap-plied to the connectors. To prevent tension, create a loop in the cable close to the sen-sor and tie the loop with cable ties, as in the figure below.• Wrap the junction of the connectors with self vulcanizing tape for waterproofing.• Fasten the cable to the mast, etc. at the neck of each connector with a cable tie.Flat washerSensor base assy.PlatformHex bolt(See below.)Apply marine sealant.LSpring washerPlatform thickness and bolt to usePlatform thickness Bolt to use5 mm or less M10×20 (Supplied, prefastened to radome.)6 - 10 mm M10×25 (Supplied.)Over 10 mm Use bolt where the length of “L” above is 15 mm. Supply locally.1: Red2: Braid3: BluePower cablepin assignmentLoop cable and tieloop with cable ties.TENTATIVE
3. INSTALLATION14Installation with the radome mountThe optional radome mount lets you fasten the radar sensor to a mast on a sailboat.Name, Type: Radome Mount, OP03-209Code No.: 001-078-350How to assemble the bracket1. Fasten the fixing plates to brackets (1) and (2) with four M8×20 hex bolts.2. Fit brackets (1) and (2) loosely with sup-port plates (1) and (2) using four M4×12 hex bolts, so that the gap between the brackets can be adjusted.3. Place the mounting plate on the bracket and fix it loosely with four M8×20 hex bolts.How to fasten the bracket to the mast1. Drill eight holes of 6.5 mm diameter in the mast and fix the bracket with eight stain-less steel rivets (local supply) of 6.4 mm diameter.2. Tighten the bolts on the bracket.3. Fasten the radar sensor to the bracket.Connect the power cable to the power source, observing the guidelines for laying the power cable shown on this page.Name Type Code No. QtyMounting plate03-018-9001-0100-206-740-101Support plate (1)03-018-9005-0100-206-780-101Support plate (2)03-018-9006-0100-206-790-101Bracket(1)03-028-9101-1100-206-811-101Bracket(2)03-028-9101-2100-206-812-101Fixing plate03-028-9103-1100-206-831-102Hex bolt w/washerM8×20 SUS304000-162-955-108Hex bolt w/washerM4×12 SUS304000-162-956-104Mounting plateSupportplate (1)Supportplate (2)Bracket (1)FixingplateM8×20ASSEMBLEDRADOME MOUNTM8×20M8×20M4×12How to assemble the radome mountRivetM10×25How to fasten the sensor to the radome mountBracket (2)TENTATIVE
3. INSTALLATION153.4 How to Set up the Radar SensorBefore you can set up and use the radar sen-sor, download and install the free application [Marine Radar] from the App Store. The appli-cation is common to both the iPad and theiPhone.Set up the radar as shown in this section, in the order given.An insert sheet requests you to attach the supplied SSID and password label to the in-sert sheet. Attach the label to the sheet, and store the sheet in a safe place for future refer-ence.3.4.1 How to start the systemPower the sensor. Open your iOS terminal, then turn on the wireless LAN function (in the [Settings] menu) if it is not already on. Tap the [Marine Radar] application (see right figure, appearance subject to change) in your terminal.The splash screen appears for a few mo-ments, then the application tries to connect to the radar sensor, which normally takes no more than three seconds. If the connection is successful, the [Preheating] display appears. If the connection could not be made, an error message appears. Tap the [Search again] button to try to connect to the sensor. If the application cannot connect to the sensor, check to see if the wireless LAN function is enabled on your terminal.After the preheating is completed, which takes approx. 90 seconds, the radar goes into standby. Tap the STB-TX icon at the top right corner on the display to transmit.3.4.2 Heading, timingadjustmentHow to open the Installation Settings menuTo adjust the heading or timing, you must first open the [Installation Settings] menu.1. Open the menu, Settings menu:1) iPad: Tap the menu tab at the bottom right corner to open the menu.iPhone: Tap anywhere to open the menu.2) iPad, iPhone: Tap the Settings menu icon ( ) to show the Settings menu.2. Tap [Installation Settings]. You are asked to input the pass code.3. Use the software keyboard to enter 1234.4. Tap [Back] twice to close the menu and return to the radar display. Splash screenSearching radar sensorPreheatingdisplayMenu tabSettings menu iconHow to open the Settings menu on the iPadTENTATIVE
3. INSTALLATION16Heading alignmentYou have mounted the radar sensor facing straight ahead in the direction of the bow. Therefore, a small but conspicuous target dead ahead visually should appear on the heading line (zero degrees). In practice, you will probably observe some small error on the display because of the diffi-culty in achieving accurate initial positioning of the sensor. The following adjustment com-pensates for this error.1. Open the menu, Picture menu:1) iPad: Tap the menu tab at the bottom right corner to open the menu.iPhone: Tap anywhere to open the menu.2) iPad, iPhone: Tap the ( ) icon to open the Picture menu.2. Tap the menu navigation buttons ( ) to select [Heading Align].3. Visually identify a suitable target (for ex-ample, ship or buoy) at a range between 0.125 to 0.25 miles.4. Point your boat’s bow directly toward the target selected at step 3.5. Locate the target selected at step 3 on the display and choose a range which places the target in the outer half of the picture.6. Adjust the slider bar so the target be-comes centered on the heading line.Timing adjustmentThe timing is automatically adjusted. Howev-er, if a “straight” target (harbor wall, etc.) ap-pears to be pushed or pulled, as shown below, adjust the sweep timing to straighten the target and prevent incorrect placement of all targets.1. Transmit on a range between 0.125 and 0.5 nm.2. Open the Picture menu, referring to step 1 in “Heading alignment”.Menu tabPicture menu iconHow to open the Picture menu on the iPad/Heading lineHeading lineHeading Align (0~359)3 / 5Heading lineTar ge tCorrect Target pushedinwardTarget pushedoutwardTENTATIVE
3. INSTALLATION173. Tap the menu navigation buttons ( ) to select [Timing Adjustment].4. Select [Manual] or [Auto]. For [Auto] go to step 7. For [Manual] go to step 5.5. Find a target which should be displayed “straightly” (harbor wall, straight pier) on the radar display.6. While looking at the target selected at step 5, operate the slider bar to straighten the target.7. Tap the display area to close the window.3.4.3 Range unitThe range can be shown in nautical miles or kilometers, and the default setting is nautical miles. To change the unit, do as follows:1. Open the Settings menu, referring to step 1 in “How to open the [Installation Set-tings] menu” on page 15.2. Tap [Initial Settings].3. Tap [Units] then select range unit.3.4.4 Tuning initializationTuning is automatically adjusted when the ra-dar transmits, therefore initialization is not necessary. (Initialization is necessary only when the magnetron is replaced.)3.4.5 Sector blankA sector blank is an area on the radar display where no radar echoes appear because an obstruction near the radar sensor (for exam-ple, a mast) blocks reception within that area. This area should be marked on the display to alert you that no echoes will be shown there. If you do not have this problem, skip this pro-cedure.As an example, the procedure below shows how to set a 20° sector blank between 170° and 190°.1. Open the Picture menu, referring to step 1 in “Heading alignment” on page 16.2. Tap the item selection buttons ( ) to select [Sector Blank].3. Tap the [On] button.4. At [Sector Start], drag the slider bar to set the start bearing relative to the heading line. (Use the or button to fine tune the setting.) In the example, set “170”.5. At [Sector Angle], drag the slider bar to set the width of the sector. In the exam-ple, set “20”.The sector is marked on the display with dashed green lines.To disable the sector, tap [Off] at [Sector Blank]./Heading Align (0~359)3 / 5UnitsTune Initializenm>/5 / 5+Sector blankSector blankTENTATIVE
AP-1APPENDIX 1 MENU TREERain (Manual, 0~100; Auto)Echo Stretch (Off, Low, High)Heading Align (0.0~359.9°)Timing Adjustment* (Manual, Auto)Sector Blank* (Off, On)SettingsmenuSettingsmenuPicturemenuPicturemenuColormenuColormenuDisplay SettingsInitial SettingsInstallation Settings (Antenna Rotation, Jamming, On Time, Tx Time, Video Contrast, Factory Default)Self TestOperation GuideVersionUnits (nm, km)Tune InitializeFull Screen (Off, On)Range Ring (Off, On)Own Ship Mark (Off, On)Sector Start (0~359°)Sector Angle (0~135°)Palette (Day, Night)Echo Color (Yellow, Green, Multi)Screen Tone (0-16)* Shown when Installation Setting menu is activated.TENTATIVE
AP-2APPENDIX 2 RADIO REGULATORY INFORMATIONWireless interoperabilityThis product is designed to be interoperable with any wireless LAN product that is based on direct sequence spread spectrum (DSSS) and orthogonal frequency division multiplexing (OFDM) radio technology and to comply with the following standards.• IEEE Std 802.11b Standard on 2.4 GHz Wireless LAN• IEEE Std 802.11g Standard on 2.4 GHz Wireless LAN• IEEE Std 802.11n Standard on 2.4 GHz Wireless LANSafetyThis product, like other radio devices, emits radio frequency electromagnetic energy. The level of energy emitted by this device, however, is less than the electromagnetic energy emitted by other wireless devices such as mobile phones. This product operates within the guidelines found in ra-dio frequency safety standards and recommendations. These standards and recommendations reflect the consensus of the scientific community and result from deliberations of panels and com-mittees of scientists who continually review and interpret the extensive research literature. In some situations or environments, the use of this product may be restricted by the proprietor of the building or responsible representatives of the applicable organization. Examples of such situa-tions include the following:• Using this product onboard airplanes, or• Using this product in any other environment where the risk of interference with other devices or services is perceived or identified as being harmful.If uncertain of the policy that applies to the use of wireless devices in a specific organization or environment (an airplane, for example), ask for authorization to use this product before turning it on.Export RegulationRadio wave certification is necessary at the export destination. The Wireless LAN of this product operates in the 2.4 GHz band, which does not require a license in most countries. However, the conditions for use of the wireless LAN depend on the country or the area.TENTATIVE
APPENDIX 2 RADIO REGULATORY INFORMATIONAP-3USA-Federal Communications CommissionThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy. If not installed and used in accordance with the instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interfer-ence will not occur in a particular installation.If this equipment does cause harmful interference to radio or television reception, which can be determined by tuning the equipment off and on, the user is encouraged to try and correct the in-terference by one or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the distance between the equipment and the receiver.• Connect the equipment to outlet on a circuit different from that to which the receiver is connect-ed.• Consult the dealer or an experienced radio/TV technician for help.This device complies with part 15 of the FCC Rules. Operation is subject to the following two con-ditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.Caution: Exposure to Radio Frequency Radiation• This equipment complies with FCC radiation exposure limits set forth for an uncontrolled envi-ronment and meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65.• This equipment should be installed and operated keeping the radiator at least 20cm or more away from person's body.• This device must not be co-located or operating in conjunction with any other antenna or trans-mitter.TENTATIVE
APPENDIX 2 RADIO REGULATORY INFORMATIONAP-4Canada-Industry Canada (IC)This device complies with RSS 210 of Industry Canada.Operation is subject to the following two conditions:(1) This device may not cause interference, and(2) This device must accept any interference, including interference that may cause undesired op-eration of this device.L'utilization de ce dispositif est autorisée seulement aux conditions suivantes:(1) il ne doit pas produire de brouillage et.(2) l'utilisateur du dispositif doit etre pret a accepter tout brouillage radioelectrique recu, meme si ce brouillage est susceptible de compromettre le fomctionnement du dispositif.Caution: Exposure to Radio Frequency RadiationThis equipment complies with IC radiation exposure limits set forth for an uncontrolled environ-ment and meets RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment should be installed and operated keeping the radiator at least 20cm or more away from person's body.Cet équipement est conforme aux limites d'exposition aux rayonnements énoncées pour un envi-ronnement non contr êolé et respecte les règles d'exposition aux fréquences radioélectriques (RF) CNR-102 de l'IC. Cet équipement doit etre installé et utilise en gardant une distance de 20 cm ou plus entre le dispositif rayonnant et le corps.To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (EIRP) is not more than that required for successful communication.TENTATIVE
FURUNO DRS4W SP - 1 E3636S01A 140205 SPECIFICATIONS OF RADAR SENSOR DRS4W 1 RADIATOR 1.1 Antenna type Patch array antenna 1.2 Antenna length 15-inch 1.3 Horizontal beam width 7.2° (3 dB) 1.4 Vertical beam width 25° (3 dB) 1.5 Gain 20 dBi or more 1.6 Sidelobe attenuation -18 dB (within ±20°), -20 dB (±20° or more) 1.7 Rotation 24 rpm 2 RADAR FUNCTION 2.1 Tx frequency 9410±30 MHz, P0N 2.2 Output power 4 kW 2.3 Duplexer Ferrite circulator 2.4 Intermediate frequency 60 MHz 2.5 Range, Pulse length and Pulse repetition rate Range (NM) Pulse length (μs) PRR (Hz approx.) 0.125 to 0.5 0.08 360 0.75 to 2 0.3 360 3 to 24 0.8 360 2.6 Minimum range 25 m 2.7 Range resolution 25 m 2.8 Range accuracy 1 % of range in use or 0.01 NM, which is the greater 2.9 Bearing resolution 7.2° 2.10 Bearing accuracy ±1° 2.11 Warming up time 90 s 3 INTERFACE 3.1 Wireless LAN standard IEEE 802.11 b 3.2 Transmit frequency 2.4GHz nominal 3.3 Number of channel 10 ch 3.4 Receivable distance 10 m nominal 4 POWER SUPPLY 12-24 VDC: 2.1/1.0 A 5 ENVIRONMENTAL CONDITIONS 5.1 Ambient temperature -25°C to +55°C 5.2 Relative humidity 95% or less at +40°C 5.3 Degree of protection IP26 5.4 Vibration IEC 60945 Ed.4 6 UNIT COLOR N9.5 (cover), PANTONE 2945C (bottom) TENTATIVE
FURUNO DRS4W SP - 2 E3636S01A 140205 This page is intentionally left blank. TENTATIVE
ＰＡＣＫＩＮＧ　ＬＩＳＴ03HN-X-9851 -3 DRS4WN A M E O U T L I N E DESCRIPTION/CODE № Q'TY1/1ユニット UNITﾚｰﾀﾞｰｾﾝｻｰRADAR SENSORRSB-126-103000-024-973-001予備品 SPARE PARTS予備品SPARE PARTSSP03-17801001-265-910-001工事材料 INSTALLATION MATERIALS工事材料INSTALLATION MATERIALSCP03-35701001-265-920-001図書 DOCUMENTﾊﾟｽﾜｰﾄﾞ情報PASSWORD INFOE32-01401-*000-179-453-1*1型紙TEMPLATEE32-01314-*000-178-948-1*1取扱説明書(英)OPERATOR'S MANUAL (EN)OME-36360-*000-178-946-1*1（略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.）03HN-X-9851型式/ｺｰﾄﾞ番号が２段の場合、下段より上段に代わる過渡期品であり、どちらかが入っています。　なお、品質は変わりません。TWO TYPES AND CODES MAY BE LISTED FOR AN ITEM. THE LOWER PRODUCT MAY BE SHIPPED IN PLACE OF THE UPPER PRODUCT. QUALITY IS THE SAME.TENTATIVEA-1
30/Jan/2014 H.MAKITENTATIVED-1
243A1BCDRAWNCHECKEDAPPROVEDDWG.No.TITLENAME名称REF.No.SCALE MASS kgT.YAMASAKIINTERCONNECTION DIAGRAM相互結線図DRS4WレーダーセンサーRADAR SENSOR03-184-6011-0H.MAKI2.4 GHz, IEEE802.11b123SHIP'S MAIN-HSHIP'S MAIN-CGNDW802アカアオREDBLURSB-126-103レーダーセンサーRADAR SENSOR(+)(-)12-24VDC FRU-3P-FF-15M,15m,φ10.3 5A24VDC*1: OPTION.NOTE注記＊１）オプション。FRU-3P-FF-10M,10m,φ8.6(*1)FRU-3P-FF-20M,20m,φ10.3(*1)FRU-3P-FF-30M,30m,φ8.6(*1)C3636-C01- B24/Feb/201424/Feb/201425/Feb/2014 H.MAKITENTATIVES-1
FURUNO Worldwide Warranty for Pleasure Boats (Except North America) This warranty is valid for products manufactured by Furuno Electric Co. (hereafter FURUNO) and installed on a pleasure boat. Any web based purchases that are imported into other countries by anyone other than a FURUNO certified dealer may not comply with local standards. FURUNO strongly recommends against importing these products from international websites as the imported product may not work correctly and may interfere with other electronic devices. The imported product may also be in breach of the local laws and mandated technical requirements. Products imported into other countries as described previously shall not be eligible for local warranty service. For products purchased outside of your country please contact the national distributor of Furuno products in the country where purchased. This warranty is in addition to the customer´s statutory legal rights. 1. Terms and Conditions of Warranty FURUNO guarantees that each new FURUNO product is the result of quality materials and workmanship. The warranty is valid for a period of 2 years (24 months) from the date of the invoice, or the date of commissioning of the product by the installing certified dealer. 2. FURUNO Standard Warranty The FURUNO standard warranty covers spare parts and labour costs associated with a warranty claim, provided that the product is returned to a FURUNO national distributor by prepaid carrier. The FURUNO standard warranty includes:  Repair at a FURUNO national distributor  All spare parts for the repair  Cost for economical shipment to customer 3. FURUNO Onboard Warranty If the product was installed/commissioned and registered by a certified FURUNO dealer, the customer has the right to the onboard warranty. The FURUNO onboard warranty includes • Free shipping of the necessary parts • Labour: Normal working hours only • Travel time: Up to a maximum of two (2) hours • Travel distance: Up to a maximum of one hundred and sixty (160) KM by car for the complete journey 4. Warranty Registration For the Standard Warranty - presentation of product with serial number (8 digits serial number, 1234-5678) is sufficient. Otherwise, the invoice with serial number, name and stamp of the dealer and date of purchase is shown. For the Onboard Warranty your FURUNO certified dealer will take care of all registrations. 5. Warranty Claims For the Standard Warranty - simply send the defective product together with the invoice to a FURUNO national distributor. For the Onboard Warranty – contact a FURUNO national distributor or a certified dealer. Give the product´s serial number and describe the problem as accurately as possible. Warranty repairs carried out by companies/persons other than a FURUNO national distributor or a certified dealer is not covered by this warranty. 6. Warranty Limitations When a claim is made, FURUNO has a right to choose whether to repair the product or replace it. The FURUNO warranty is only valid if the product was correctly installed and used. Therefore, it is necessary for the customer to comply with the instructions in the handbook. Problems which result from not complying with the instruction manual are not covered by the warranty. FURUNO is not liable for any damage caused to the vessel by using a FURUNO product. The following are excluded from this warranty: a. Second-hand product b. Underwater unit such as transducer and hull unit c. Routine maintenance, alignment and calibration services. d. Replacement of consumable parts such as fuses, lamps, recording papers, drive belts, cables, protective covers and batteries. e. Magnetron and MIC with more than 1000 transmitting hours or older than 12 months, whichever comes first. f. Costs associated with the replacement of a transducer (e.g. Crane, docking or diver etc.). g. Sea trial, test and evaluation or other demonstrations. h. Products repaired or altered by anyone other than the FURUNO national distributor or an authorized dealer. i. Products on which the serial number is altered, defaced or removed. j. Problems resulting from an accident, negligence, misuse, improper installation, vandalism or water penetration. k. Damage resulting from a force majeure or other natural catastrophe or calamity. l. Damage from shipping or transit. m. Software updates, except when deemed necessary and warrantable by FURUNO. n. Overtime, extra labour outside of normal hours such as weekend/holiday, and travel costs above the 160 KM allowance o. Operator familiarization and orientation. FURUNO Electric Company, March 1, 2011 TENTATIVE
FURUNO Warranty for North America FURUNO U.S.A., Limited Warranty provides a twenty-four (24) months LABOR and twenty-four (24) months PARTS warranty on products from the date of installation or purchase by the original owner. Products or components that are represented as being waterproof are guaranteed to be waterproof only for, and within the limits, of the warranty period stated above. The warranty start date may not exceed eighteen (18) months from the original date of purchase by dealer from Furuno USA and applies to new equipment installed and operated in accordance with Furuno USA’s published instructions. Magnetrons and Microwave devices will be warranted for a period of 12 months from date of original equipment installation. Furuno U.S.A., Inc. warrants each new product to be of sound material and workmanship and through its authorized dealer will exchange any parts proven to be defective in material or workmanship under normal use at no charge for a period of 24 months from the date of installation or purchase. Furuno U.S.A., Inc., through an authorized Furuno dealer will provide labor at no cost to replace defective parts, exclusive of routine maintenance or normal adjustments, for a period of 24 months from installation date provided the work is done by Furuno U.S.A., Inc. or an AUTHORIZED Furuno dealer during normal shop hours and within a radius of 50 miles of the shop location. A suitable proof of purchase showing date of purchase, or installation certification must be available to Furuno U.S.A., Inc., or its authorized dealer at the time of request for warranty service. This warranty is valid for installation of products manufactured by Furuno Electric Co. (hereafter FURUNO). Any purchases from brick and mortar or web-based resellers that are imported into other countries by anyone other than a FURUNO certified dealer, agent or subsidiary may not comply with local standards. FURUNO strongly recommends against importing these products from international websites or other resellers, as the imported product may not work correctly and may interfere with other electronic devices. The imported product may also be in breach of the local laws and mandated technical requirements. Products imported into other countries, as described previously, shall not be eligible for local warranty service. For products purchased outside of your country please contact the national distributor of Furuno products in the country where purchased. WARRANTY REGISTRATION AND INFORMATION To register your product for warranty, as well as see the complete warranty guidelines and limitations, please visit www.furunousa.com and click on “Support”. In order to expedite repairs, warranty service on Furuno equipment is provided through its authorized dealer network. If this is not possible or practical, please contact Furuno U.S.A., Inc. to arrange warranty service. FURUNO U.S.A., INC. Attention: Service Coordinator 4400 N.W. Pacific Rim Boulevard Camas, WA 98607-9408 Telephone: (360) 834-9300 FAX: (360) 834-9400 Furuno U.S.A., Inc. is proud to supply you with the highest quality in Marine Electronics. We know you had several choices when making your selection of equipment, and from everyone at Furuno we thank you. Furuno takes great pride in customer service. TENTATIVE

Navigation menu