Fukuda Denshi Co DS7100 Patient Monitor User Manual DS71v1 1 FA 02 Operation 004

Fukuda Denshi Co Ltd Patient Monitor DS71v1 1 FA 02 Operation 004

User manual 3

2−11Press the ID key.Enter the ID number using the numeric keypad.3. Enter the patient’s birth date.Press the Age key.Enter the birth date using the numeric keypad.4. Select the patient type, and Used / Not used of pacemaker use.Select the patient type from Adult , Child ,or Neonate .Select the pacemaker use from Used , Not used .WARNING The patient type and pacemaker use must be selected. The patient typeselection influences the precision of the QRS detection and NIBPmeasurement. Make sure the correct selection is made.2To Start Monitoring
2−12− Basic Operation −Scale, Lead, Baseline Position Setup (Parameter Key)1. Select the parameter to set the scale / lead / baseline position. (Ex.: ECG)Press the parameter key where heart rate is displayed.2. Press the Lead・Size key. The menu to adjust size / lead / baseline position will bedisplayed.3. Adjust the waveform size.Select an appropriate waveform size for the monitoring waveform.CAUTION The arrhythmia detection level corresponds with the displayed waveformsize. Select an appropriate size for monitoring.
2−134. Select the lead.Select an appropriate lead according to the monitoring purpose.5. Adjust the baseline position.Use the ? , ? keys to adjust the waveform baseline position.ReferenceUse the same procedure for each parameter.Refer to section for each parameter in “6. Parameter Setup”.2Basic Operation
2−14Scale, Lead, Baseline Position Setup (User Key)Pressing the Lead・Size key will display thearrow keys on the home display to adjustwaveform size, scale, lead, baseline position.1. Select the waveform size, lead, baseline position for ECG waveform.Adjust the waveform suitable for monitoring.Pressing the Lead key will sequentially changethe lead.3-electrode:Ⅰ→Ⅱ→Ⅲ→Ⅰ4-electrode:Ⅰ→Ⅱ→Ⅲ→aVR→aVL→aVF→Ⅰ5-electrode:Ⅰ→Ⅱ→Ⅲ→aVR→aVL→aVF→V→ⅠPressing the Size key will sequentially change thesize.×1/4→×1/2→×1→×2→×4→×1/4Use the ↑, ↓ keys to adjust the baseline positionup or down.2. Select the scale for BP, CO2 waveform.Pressing the Scale key will sequentially switch thescale.3. Select the waveform size for impedance respiration waveform, SpO2 waveform.Pressing the Size key will sequentially change thesize.×1/4→×1/2→×1→×2→×4→×1/4
2−15Alarm Setup for Each ParameterThe alarm can be set for each parameter. By pressing the selected parameter key, upper andlower alarm limit and ON/OFF of alarm can be set.1. Select the parameter to set the alarm. (Ex.: HR alarm)2. Press the HR Alarm key. The menu to adjust the alarm limit will be displayed.3. Set the upper and lower alarm limit.Use the ? , ? keys to adjust the lower limit.Use the ? , ? keys to adjust the upper limit.ReferenceUse the same procedure for the setup of each parameter.Refer to section for each alarm in “6. Parameter Setup”Lower LimitUpper Limit2Basic Operation
2−16ON/OFF of Parameter Display Waveform/Numeric Data DisplayThe waveform and numeric data display for each parameter can be turned ON or OFF withoutchanging the display configuration. If not performing the ECG or SpO2 measurement while theECG cable or SpO2 sensor is connected to the monitor, the equipment status alarm such as “LeadOff” will generate. Removing ECG or SpO2 from the display configuration will not generate suchalarm, but this function may be more useful as it allows to turn off the measurement withoutchanging the display configuration.This function is not available for NIBP monitoring.1. Select the parameter to turn off the display. (Ex.: ECG) 2. Press the Display ON/OFF key. The confirmation display for ON/OFF of ECG displaywill appear. 3. Select Display ON or Display OFF .Pressing the Display ON key will display thewaveform and numeric data.Pressing the Display OFF key will not display thewaveform and numeric data.4. Automatic resetFor ECG, impedance RESP, SpO2, CO2, properly connecting the sensor will automatically set thedisplay ON/OFF function to “Display ON”.ReferenceFor automatic reset condition, refer to Display ON/OFF section for each parameter in“6. Parameter Setup”.The Display OFF message will bedisplayed inside the parameter key.
2−17Recording●Start / Stop of Waveform RecordingPressing the Rec. START/STOP key on thehome display will start the waveform recording.Up to 3 waveforms can be recorded.【Example of Recording】ReferenceFor the manual recording, number of recording waveforms and recording duration can be set.Refer to “4. Monitoring Setup Manual Recording” for details.For the alarm recording, number of recording waveforms, recording duration, alarm factor can beset.Refer to “4. Monitoring Setup Alarm Recording” for detailsFor the periodic recording, number of recording waveforms, recording duration, recordingintervals can be set.Refer to “4. Monitoring Setup Periodic Recording” for details.The monitoring data of the patient such as graphic trend and tabular trend can be recorded.Refer to sections on graphic trend and tabular trend in “7. Function”.Bed IDPatient NameWaveform Type, Lead, SizeRecording Speed Rec. Mode Delay Time Telemetry Channel Filter ModeRecorded Time Sex Age Patient ID Patient Type Measured Data2Basic Operation
2−18To Install the Paper1. Press the button located at the right side of the recorder magazine.2. The magazine will come out.3. Pull out the magazine from the monitor.4. Set the recording paper so that the mark printed on each paper comes to the right.5. Place the magazine back into the monitor. Push in until it locks into place with a clicksound.Mark
2−19To Suspend MonitoringWhen not monitoring for a while, turning OFF the power will erase the recall data, STmeasurement, OCRG data.However, using the cease monitoring function allows suspension of data measurement, alarmgeneration, automatic measurement, automatic recording without erasing the data or setupdetails.1. Press the Cease key on the admit / discharge menu.Press the Menu → Admit / Discharge → Cease key.2. Suspend monitoring.Pressing the OK key on the confirmationdisplay will interrupt monitoring.Pressing the Cancel key will return to theprevious display.3. Verify that the monitoring is suspended.The Resume key will be displayed on thehome display. On the home display, numericdata and waveform display will be ceased, andall the key operation except the Resumekey will become ineffective.NOTEThe telemetry transmission will cease when monitoring is suspended.(for DS-7141, DS-7101LT)Note that the square wave will be displayed on the central monitor indicating thetoo far condition of the telemetry.2Basic Operation
2−20Discharging ProcedureThis procedure will erase the past data, such as patient name, ID, age, tabular / graphic trend, andrecall.1. Press the Discharge key on the admit / discharge menu.Press the Menu → Admit / Discharge → Discharge key.2. Perform discharge procedure.Pressing the OK key on the confirmationdisplay will discharge the patient.Pressing the Cancel key will return to theprevious display.
2−21− Operation Flow −The operation flow of this system is as follows.【Menu】Admit /DischargePatient Name / ID / Sex Discharge Room / Bed IDPatient Type (Adult / Child / Neonate) Mode Selection PacemakerAge Cease Monitor Filter ModeParameter Setup Zero BalanceGraphic Trend OCRGTabular Trend Alarm SetupNIBP List Volume SetupRecall Display ConfigurationST Display Night ModeOther Bed【System Configuration】Night Mode SetupRecord SetupSweep SpeedBrightness SetupIC CardColor SetupTelemetry Waveform Setup【Preset】Alarm Mode SetupHospital SetupWard SetupMonitor SetupDisplay Mode SetupTest Menu2Operation Flow
2−22Blank Page

Navigation menu