Fujitsu 2012-001-SNB Communication Module User Manual ver1 3x

Fujitsu Limited Communication Module ver1 3x

User manual

User manual 1/10 User manualUser manualUser manualUser manual Ver 1.3
User manual 2/10 CCCChange historyhange historyhange historyhange history revision Updated date summary 1.0 Aug 1 2012 First edition 1.1 Aug 6 2012 Modification Page 6(DSSS/CCK->DSSS/BPSK),7(modification of consumption), 8(addition of following sentence) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 1.2 August 15 2012 -Fixing of 3.1(delete comments of remarks) - addition of 5.6 Indicating compliance with ICES-003 1.3 August 28 2012 - Fixing of 4.3
User manual 3/10 Table of contentsTable of contentsTable of contentsTable of contents 1. Apprication ..................................................................................................................................... 4 2. System Configuration ..................................................................................................................... 4 3. Description of Meter (Host) ............................................................................................................ 5 3.1 Overview .................................................................................................................................... 5 3.2 Operating Range ........................................................................................................................ 5 4. Description of Module ( Module) .................................................................................................... 6 4.1 Overview .................................................................................................................................... 6 4.2 Operating Range ........................................................................................................................ 6 4.3 Major element ............................................................................................................................ 6 4.4 Basic specification 【module】 .................................................................................................... 7 5. Required FCC and IC statement ( Host ) ....................................................................................... 8 5.1 FCC §15.21 ................................................................................................................................ 8 5.2 FCC §15.105 .............................................................................................................................. 8 5.3 RSS-Gen §7.1.2. ........................................................................................................................ 8 5.4 RSS-Gen §7.1.3. ........................................................................................................................ 8 5.5 Indicating safe separation distance warning .............................................................................. 9 6. Required FCC and IC statement (Module)...................................................................................10 6.1 FCC §15.21 ..............................................................................................................................10 6.2 FCC §15.105 ............................................................................................................................10 6.3 RSS-Gen §7.1.2. ......................................................................................................................10 6.4 RSS-Gen §7.1.3. ......................................................................................................................10
User manual 4/10 1. Apprication This document shows the description of wattmeter（hereinafter called meter）and mounted communication board（hereinafter called module）. - target meters : GE I210+ Meter FM1S / FM2S / FM12S / FM25S - Module : Fujitsu YAA75-0402 2. System Configuration Fig2-1 is general system configuration of using meter. Installed meters in each house is communicated to Center via Repeaters and Gateways and control the meter-reading value etc.automatically. Red line of Fig.2-1 is the applicable scope of this document. Fig2-1 System configuration Substation Poles Houses…..CenterServer -DHCP ServerRouterRouter Fiber-optnetwork SwitchMeters RepeatersGateway
User manual 5/10 3. Description of Meter (Host) 3.1 Overview Form and overview of meter are as follows. Category Meter form Remark FM1S FM2S FM12S FM25S Input voltage 120VAC 240VAC 120VAC or 240VAC 120VAC or 240VAC enclosure Same form Meter panel board Same board Meter socket type Different type Mouted module Same module meter panel interface Same interface AC power cable Same cable 3.2 Operating Range • Voltage : + - 20% (or ±20%) • Temperature : -40°C through +85°C • Typical Starting Watts : <=5.0 Watts (Form 2S 240V CL200) • Typical Watts Loss : 0.7 Watts • Typical Accuracy : Within +/- 0.2%
User manual 6/10 4. Description of Module ( Module) 4.1 Overview The module mounted to each meter in paragraph 3 collects the meter-reading values etc. with controlling Center. 4.2 Operating Range Same as chapter 3.2. 4.3 Major element Major elements of module are as follows. No. component summary remark 1 Radio element IEEE802. 11b Transmission power:100mW Modulation：DSSS / BPSK Data rate ：1Mbps ２２２２ Antenna This antenna made by printed-circuit in the module. 3 Meter panel interface element Communication between Meter panel. Signals:refer to chapter 3.2 4 Power element *AC cable(with ferrite bead) is connected to this element. *This element steps down AC input(120V/240V) to +3.3VDC. 5 Dispray element extinction power off or normal operation LED(green) blinking No operation ( start-up firmware) lighting No operation(reset / no service) extinction normal LED(red) blinking fault lighting reset AC cable with ferrite bead 120/ 240VAC Meter *Display *Meter information collection Meter panel module Power element Radio element antenna element Meter Socket From electric pole 120VAC / 240VAC 120VAC / 240VAC +3.3VDC UART/ Control signal Meter panel Interface element
User manual 7/10 4.4 Basic specification 【【【【module】】】】 No Item specification 1 External interface Wireless IEEE802. 11b Meter Panel Connector（10pin） Power Input : AC85～264V 2 Debug interface RESET FRES1/2 Short-circuit MB86C90 JTAG:×1 AR2315 JTAG:×1 3 Display LED Status ：GREEN Alarm ：AMBER 4 Security Tamper Program Deletion 5 Power Input AC-DC Conversion （120V/240V⇒3.3V） Frequency 50/60Hz consumption Input : Less than 8.49W(AC:120V/240V) Output : Less than 5.94W(DC:+3.3V) 6 Condition Operating temperature -20℃～40℃ 7 Cooling method Air cooling without blower 8 Thunder surge Protection fuse varistor fuse
User manual 8/10 5. Required FCC and IC statement ( Host ) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 5.1 FCC §15.21 Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. 5.2 FCC §15.105 For class B equipment: NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: — Reorient or relocate the receiving antenna. — Increase the separation between the equipment and receiver. — Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. — Consult the dealer or an experienced radio/TV technician for help. 5.3 RSS-Gen §7.1.2. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante. 5.4 RSS-Gen §7.1.3. This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
User manual 9/10 5.5 Indicating safe separation distance warning This equipment complies with radio frequency exposure limits set forth by the FCC and Industry Canada for an uncontrolled environment. This equipment should be installed and operated with a Minimum distance of 20cm between the device and the user or bystanders. This device must Not be co-located or operating in conjunction with any other antenna or transmitter. Cet équipement est conforme aux limites d'exposition aux radiofréquences définies par la FCC et Industrie Canada pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre le dispositif et l'utilisateur ou des tiers. Ce dispositif ne doit pas être utilisé a proximité d’une autre antenne ou d’un autre émetteur. 5.6 Indicating compliance with ICES-003 This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe or B est conforme à la norme NMB-003 du Canada
User manual 10/10 6. Required FCC and IC statement (Module) 6.1 FCC §15.21 Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. 6.2 FCC §15.105 For class B equipment: NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: — Reorient or relocate the receiving antenna. — Increase the separation between the equipment and receiver. — Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. — Consult the dealer or an experienced radio/TV technician for help. 6.3 RSS-Gen §7.1.2. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante. 6.4 RSS-Gen §7.1.3. This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.

Navigation menu