Fujitsu Technology Solutions SCENIC6651 personal computer User Manual A26361 K520 Z100 4 7619

Fujitsu Technology Solutions GmbH personal computer A26361 K520 Z100 4 7619

Manual Scenic 600 Oct 99 part 5

System expansionsA26361-K520-Z100-4-7619 33132aPush the rear slot cover plate into the slot (1). Ensure that the point of the cover engages intothe guide (a).Replace the clip (2) which fixes the board. Make sure that the clip engages when released (3).Close the system unit (see "Assembling the system unit").iIf you have installed or removed a PCI board, please check in the BIOS Setup the settingsfor the relevant PCI slot. If necessary, change the settings. Further information is providedin the documentation for the PCI board.Installing and removing drivesThe system unit houses a total of three accessible drives (two 5 1/4-inch drives and one 3 1/2-inchdrive) and two non-accessible half-height (Slimline) drives .IDE drivesBy default four IDE drives are supported. Ideally hard disks are connected to IDE port 1, andaccessible IDE drives, for example CD-ROMs, to IDE port 2 (see also the Technical Manual for thesystem board).SCSI drivesIf you want to install an SCSI drive, you require an SCSI controller and an SCSI cable. Note that:• not every SCSI controller is suitable for operating SCSI hard disks• each SCSI device must be assigned its own SCSI-ID.• the SCSI cable must always be terminated at the end, either by a drive or by a terminatingresistor on the cable. The terminating resistors of all other SCSI devices attached must not beactivated or connected.• depending on the SCSI technology (UW, U2W), an adapter may be required for connecting theSCSI drives with a 50-pin connector.
System expansions34 A26361-K520-Z100-4-7619Installing an accessible driveOpen the system unit (see "Opening the system unit").iShould the chipcard reader get in the way of the accessible drive during installation, thenremove the reader (see "Installing/removing a chipcard reader").AB12Pry the plastic drive cover (A) out of the front cover.Pry the shielding plate (B) on left-hand side out of the bay.!Do not throw away the covers. If you remove the drive again later, you will have toreinstall the covers.Take the new drive out of its packaging.Make the required settings on the drive (if necessary, on installed drives as well).21ABA = Position of the screw for the upper driveB = Position of the screw for the lower driveSlide the drive into the system unit (1).Plug the data and the power supply connectors into the drive.Fasten the drive with the screw (2).If you have removed the chipcard reader, then reinstall it.
System expansionsA26361-K520-Z100-4-7619 35Close the system unit (see "Assembling the system unit").iIf necessary, you must adapt the entry for the drive in the Setup menu.Installing a hard disk drive in the front bayOpen the system unit (see "Opening the system unit").Make the required settings (e.g. master-slave) on the hard disk drives.Fasten the drive with the four screws (2).Install the installation frame with the drive in the desired front bay (see "Installing an accessibledrive").Close the slot with the panel. Ensure that the cover engages.Close the system unit (see "Assembling the system unit").
System expansions36 A26361-K520-Z100-4-7619Removing an accessible driveOpen the system unit (see "Opening the system unit").Pull the data and the power supply connectors from the desired drive.iShould the chipcard reader get in the way of the accessible drive during installation, thenremove the reader (see "Installing/removing a chipcard reader").12ABA = Position of the screw for the upper driveB = Position of the screw for the lower driveRemove the relevant screw (1) and take the drive out of the system unit (2).ABInsert the shielding plate (B) on the right-hand side on the installation bay and press it in.Press the plastic drive cover (A) into the front panel until it snaps in place.If you have removed the chipcard reader, then reinstall it.Close the system unit (see "Assembling the system unit").iIf necessary, you must adapt the entry for the drive in the Setup menu.

Navigation menu