Fujitsu Client Computing WL0028 TAYLOR PEAK 62205ANHMW WLAN IN Q702 STYLISTIC User Manual Q702 B6FJ 8761 01ENZ0 00

Fujitsu Limited TAYLOR PEAK 62205ANHMW WLAN IN Q702 STYLISTIC Q702 B6FJ 8761 01ENZ0 00

UserManual.wiki >

Fujitsu Client Computing >

WL0028 User Manual

User Manual

User’s GuideLearn how to use your Fujitsu STYLISTIC® Q702 Hybrid Tablet

Copyright 2012 Fujitsu America, Inc. All rights reserved. No part of this publication may be copied, reproduced, or translated, without the prior written consent of Fujitsu America, Incorporated. No part of this publication may be stored or transmitted in any electronic form without the prior consent of Fujitsu America, Inc. B6FJ-8761-01ENZ0-00USER GUIDE FOR WIRELESS BROADBAND CONNECTIONIF YOU HAVE THE OPTIONAL WIRELESS WAN (WWAN) DEVICE INSTALLED IN YOUR HYBRID TABLET, THE WWAN USER’S GUIDE IS LOCATED AT: http://solutions.us.fujitsu.com/www/content/support/mobile/support_noticesPLEASE CLICK “3G MINI-CARD GOBI3000 REGULATORY AND SAFETY INFORMATION” TO OPEN THE FULL USER GUIDE CONTAINING WARNINGS AND PRECAUTIONS ASSOCIATED WITH RF SAFETY WHEN USING THE WWAN DEVICE.DECLARATION OF CONFORMITYaccording to FCC Part 15Responsible Party Name: Fujitsu America, Inc.Address: 1250 E. Arques AvenueSunnyvale, CA 94085Telephone: (408) 746-6000Declares that product: Base Model Configuration: STYLISTIC Q702 Hybrid TabletComplies with Part 15 of the FCC Rules.This device complies with Part 15 of the FCC rules. Operations are subject to the following two conditions: (1) This device may not cause harmful interference, (2) This device must accept any interference received, including interference that may cause undesired operation.

IMPORTANT SAFETY INSTRUCTIONSThis unit requires an AC adapter to operate. Use only UL Listed I.T.E. Adapters with an output rating of 19 VDC, with a current of 3.16A (60 W).When using your Hybrid Tablet, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following:•Do not use this product near water for example, near a bathtub, washbowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool.•Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a fire. They may explode. Check with local codes for possible special disposal instructions.SAVE THESE INSTRUCTIONSFor Authorized Repair Technicians Only CAUTION: HOT SURFACE: THE BOTTOM OF THIS COMPUTER CAN BECOME HOT WHEN USED FOR LONG PERIODS OF TIME. WHEN USING THIS DEVICE, TAKE CAUTION TO LIMIT LONG TERM OR CONTINUOUS USE WHILE RESTING IT ON EXPOSED SKIN, SUCH AS THE LAP.CAUTION: RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.DANGER OF EXPLOSION IF LITHIUM (CLOCK) BATTERY IS INCORRECTLY REPLACED. REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE RECOMMENDED BY THE MANUFACTURER. DISPOSE OF USED BATTERIES ACCORDING TO THE MANUFACTURER’S INSTRUCTION.FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH THE SAME TYPE AND RATING FUSE.+AC adapter output polarity:

5 ContentsChapter 1 Getting to Know Your Hybrid TabletOverview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13Locating the Connectors and Controls. . . . . . . . . . . . . . . . . . . . . . . . . . . . .14Front Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14Back Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16Left features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17Right Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18Status Indicator Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20Display Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22Adjusting Display Panel Brightness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22Active Digitizer/Touchscreen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24Active Digitizer Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24Using the Capacitive Touchscreen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28Accessing the OnScreen TouchPad. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29Using the Nuance SoftKeyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30Caring for the Pen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30Hybrid Tablet Buttons. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33

6 - Chapter 2 Getting Started with Your Hybrid TabletPower Sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35Connecting the Power Adapters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35Starting Your STYLISTIC Hybrid Tablet. . . . . . . . . . . . . . . . . . . . . . . . . . . . 37Power On . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37Boot Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38Hard Disk Drive Passwords . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38BIOS Setup Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38Booting the System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39Starting Windows the First Time. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40Power Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41Power/Suspend/Resume Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41Sleep Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41Hibernation Feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42Windows Power Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42Restarting the System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43Powering Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43Chapter 3 User-Installable FeaturesSecure Digital Cards. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44Installing SD Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45Removing an SD Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45Keyboard Docking Station. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46Docking Station Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47Attaching the Docking Station . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48Detaching Docking Station. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49Changing the Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49Docking Station Status Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50Docking Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

7 - Battery Charge Indicator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50Battery Level Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51NumLk Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51CapsLock Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51ScrLk Indicator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51Chapter 4 Troubleshooting Your Hybrid TabletTroubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52Identifying the Problem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52Specific Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54Power On Self Test Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60Restoring Your System Image and Software. . . . . . . . . . . . . . . . . . . . . . . 61Saving and Recovering Your Factory and System Images . . . . . . . . . . . . 61Backing Up a System Image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63Recovery and Utility tabs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67Recovering your Factory Image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68Downloading Driver Updates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69Chapter 5 Care and MaintenanceCaring for your Hybrid Tablet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70Cleaning your Hybrid Tablet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71Storing your Hybrid Tablet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72Traveling with your Hybrid Tablet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73Media Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74Secure Digital Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75

8 - Chapter 6 System SpecificationsSpecifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76Microprocessor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76Chipset. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76Video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77Mass Storage Device Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78Communications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78Security Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78Device Ports. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78Power. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79Dimensions and Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79Environmental Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80Popular Accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80Included Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80Learning About Your Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81Regulatory Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84Appendix A: WLAN User’s Guide Before Using the Optional Wireless LAN . . . . . . . . . . . . . . . . . . . . . . . . . 88Wireless LAN Device Covered by this Document . . . . . . . . . . . . . . . . . . . 88Characteristics of the WLAN Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88Wireless LAN Modes Using this Device. . . . . . . . . . . . . . . . . . . . . . . . . . . 89Deactivating/Disconnecting the WLAN Device. . . . . . . . . . . . . . . . . . . . . 91Deactivation Using the Wireless On/Off Switch . . . . . . . . . . . . . . . . . . . . 92Disconnection Using the Icon in the Taskbar. . . . . . . . . . . . . . . . . . . . . . 92Activating the WLAN Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92

9 - Configuring the Wireless LAN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93Configuring the WLAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93Connection to the network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93Troubleshooting the WLAN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94WLAN Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96Using the Bluetooth Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97What is Bluetooth . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97Where to Find Information About Bluetooth . . . . . . . . . . . . . . . . . . . . . . 97Appendix B: Fingerprint Sensor DeviceIntroducing the Fingerprint Sensor Device . . . . . . . . . . . . . . . . . . . . . . . . 99Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100Installing OmniPass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100User Enrollment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102Using OmniPass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105Configuring OmniPass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110OmniPass Control Center . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114

10 PrefaceAbout This GuideThe STYLISTIC® Q702 Hybrid Tablet is a high-performance pen-based computer that has been designed to support Microsoft® Windows® 7 Professional edition.This manual explains how to operate your Hybrid Tablet hardware and built-in system software.The STYLISTIC Q702 Hybrid Tablet is a completely self-contained unit with a 11.6” HD IPS display with 160 degree vertical and horizontal viewing angles. It has a powerful interface that enables it to support a variety of optional features. Conventions Used in the GuidePages with additional information about a specific topic are cross-referenced within the text.On screen buttons or menu items appear in bold. Example: Click OK to restart your Hybrid Tablet.THE INFORMATION ICON HIGHLIGHTS INFORMATION THAT WILL ENHANCE YOUR UNDERSTANDING OF THE SUBJECT MATERIAL.THE CAUTION ICON HIGHLIGHTS INFORMATION THAT IS IMPORTANT TO THE SAFE OPERATION OF YOUR COMPUTER, OR TO THE INTEGRITY OF YOUR FILES. PLEASE READ ALL CAUTION INFORMATION CAREFULLY.

11 - About This GuideFujitsu Contact InformationService and Support You can contact Fujitsu Service and Support in the following ways:•Toll free: 1-800-8FUJITSU (1-800-838-5487)•Website: U.S.A. - us.fujitsu.com/solutions Canada - www.fujitsu.caBefore you place the call, you should have the following information ready so that the customer support representative can provide you with the fastest possible solution:•Product name•Product configuration number•Product serial number•Purchase date•Conditions under which the problem occurred•Any error messages that have occurred•Type of device connected, if anyFujitsu Shopping Online You can go directly to the online by going to the website at: www.shopfujitsu.com.THE WARNING ICON HIGHLIGHTS INFORMATION THAT CAN BE HAZARDOUS TO EITHER YOU, YOUR HYBRID TABLET, OR YOUR FILES. PLEASE READ ALL WARNING INFORMATION CAREFULLY.

12 - About This GuideMaintaining Latest Configuration To ensure that you always have the most current driver updates related to your system, you should occasionally access the Fujitsu Software Download Manager (FSDM) utility. The FSDM utility is available to allow you to download the latest drivers, utilities, and applications from the Fujitsu Support site. If you have a Windows 7 operating system, you will need to go to the Support Site (http://support.fujitsupc.com/CS/Portal/support.do?srch=DOWNLOADS). Limited Warranty Your Hybrid Tablet is backed by a Fujitsu International Limited Warranty. Check the service kit that came with your tablet for the Limited Warranty period and terms and conditions.

13 Chapter 1 Getting to Know Your Hybrid TabletOverviewThe STYLISTIC® Q702 Hybrid Tablet is a high-performance pen-based computer that has been designed to support Microsoft® Windows® 7 Professional edition.The Q702 Hybrid Tablet is called a “hybrid” because when used with the optional keyboard docking station, it has the looks and functionality of a traditional laptop.This chapter provides an overview of the STYLISTIC Q702 Hybrid Tablet and its many features. Figure 1. STYLISTIC Q702 Hybrid Tablet

14 - Locating the Connectors and ControlsLocating the Connectors and ControlsFeatures and controls that you use to operate your Hybrid Tablet are outlined below and illustrated in Figures 2 and 3. Details on using these features and controls are provided later in this manual.Figure 2. STYLISTIC Q702 Hybrid Tablet Features (Bottom, Right View)Front FeaturesFront Web Camera The front-facing HD (1280x720 pixel) web camera allows you to take pictures of yourself to send over the internet. For information on using the microphone and web cam, see the documentation associated with the YouCam application.Web Cam Access LED The web cam access LED indicates when the web camera is in use.Front Web CameraDisplaySpeakerWeb Cam Access LEDWindows ButtonSpeakerDocking Cradle Connector

15 - Locating the Connectors and ControlsDisplay The 11.6” HD IPS display offers 160 degree vertical and horizontal viewing angles.Speakers The speakers allow you to hear stereo sound from the system.Windows Button Pressing the Windows button gives you quick access to the Start menu. Docking Cradle Connector Allows you to connect the optional STYLISTIC Keyboard Docking Station.

16 - Locating the Connectors and ControlsFigure 3. STYLISTIC Q702 Hybrid Tablet Features (Back View)Back FeaturesRear Web Camera The FHD (1920x1080 pixel) rear web camera allows you to take pictures of objects in front of you for sharing over the internet. For information on using the camera, see the documentation associated with the YouCam application.Fingerprint Sensor The fingerprint sensor allows you to start your system by swiping your finger over the sensor. See “Introducing the Fingerprint Sensor Device” on page 99.Rear Web CameraFingerprint Sensor

17 - Locating the Connectors and Controls Figure 4. STYLISTIC Q702 Hybrid Tablet Features (Left View)Left featuresAir Vents The air vents are used to cool the system to prevent overheating.USB 3.0 Connector Allows you to connect Universal Serial Bus-compliant devices (compliant with USB Standard Revision 3.0) to the Hybrid Tablet.DC In Jack Allows you to connect the AC adapter or auto adapter. SD Card Slot The Secure Digital (SD) card slot allows you to insert a flash memory card for data storage. Flash memory cards allow you to transfer data to and from a variety of different digital devices. See “Secure Digital Cards” on page 44. TO PROTECT YOUR TABLET FROM DAMAGE AND TO OPTIMIZE PERFORMANCE, BE SURE TO KEEP ALL AIR VENTS UNOBSTRUCTED, CLEAN, AND CLEAR OF DEBRIS. THIS MAY REQUIRE PERIODIC CLEANING, DEPENDING UPON THE ENVIRONMENT IN WHICH THE SYSTEM IS USED. DO NOT OPERATE THE TABLET IN AREAS WHERE THE AIR VENTS CAN BE OBSTRUCTED, SUCH AS IN TIGHT ENCLOSURES OR ON SOFT SURFACES LIKE A BED OR CUSHION.Air Vents USB 3.0 ConnectorSD Card SlotDC In Jack

18 - Locating the Connectors and ControlsFigure 5. STYLISTIC Q702 Hybrid Tablet Features (Right View)Right FeaturesUSB 2.0 Connector Allows you to connect Universal Serial Bus-compliant devices (compliant with USB Standard Revision 2.0) to the Hybrid Tablet. Two additional USB 2.0 ports are located on the optional Keyboard Docking Station.Power/Suspend/Resume Switch Allows you to turn on, off, sleep, resume, hibernate or wake the Hybrid Tablet in order to optimize battery life. See “Starting Your STYLISTIC Hybrid Tablet” on page 37.Volume Up / Volume Down Buttons The Volume Up and Volume Down buttons allow you to control the volume of the tablet.Anti-theft Lock Slot The anti-theft lock slot allows you to attach an optional physical lock down device.Pen Tether Attachment Point The pen tether attachment point is used to connect your pen -- or stylus -- to the system to prevent its loss.USB 2.0 ConnectorHDMI ConnectorPower/Suspend/Resume SwitchVolume Down ButtonVolume Up ButtonRotate Display ButtonWireless Device SwitchAnti-Theft Lock SlotHeadphone/Line Out JackMicrophone/ Line In JackPen Tether Attachment Point

19 - Locating the Connectors and ControlsHeadphone/Line Out Jack The headphone jack allows you to connect headphones. See “Headphone Jack” on page 81. Microphone/Line In Jack The microphone jack allows you to connect an external stereo microphone. See “Microphone Jack” on page 81.Wireless Device On/Off switch The wireless device on/off switch is used to turn the optional WLAN, WWAN, and Bluetooth devices on and off. Switching the device off when not in use will help to extend battery life. Rotate Display Button The Rotate Display button allow you to change the orientation of the display from horizontal to vertical.HDMI Connector The HDMI port is used to connect compatible digital devices with your computer (such as a high-definition television or AV receiver).

20 - Status Indicator PanelStatus Indicator PanelIcons appear under each of the system status LEDs in the status display indicating the status of the solid state drive, system power, battery charge and battery level status. The location of icons in the Status display is shown in Figure 6.Table 1 explains how the LEDs associated with the individual icons are displayed, and describes what the variations of the displays indicate. (If an icon is not displayed, it indicates that the related system function is off or inactive. Figure 6. Status Display Icons PowerBatteryBatterySSD AccesshargeLevel

21 - Status Indicator PanelTable 1 . Status Display ConditionsIn the following table, a “blinking” LED flashes at the rate of once per second; an LED that is “blinking, slow” flashes at the rate of one second on, five seconds off. Icon LED State RemarksHard Drive AccessGreen, solid The indicator lights up green: The hard disk drive is being accessed. Battery LevelGreen, solid The battery is fully charged.Orange, solid The battery is partially charged.Red, solid The battery is nearly discharged.Off The Tablet is switched off or in Save-to-Disk mode.Charging IndicatorGreen, solid The AC Adapter is connected.Orange, solid The battery is being charged.Red, blinking Battery charging errorOff AC Adapter is disconnected. PowerBlue, solid, The system is turned on.Blue, blinking The notebook is in sleep mode (Save-to-RAM).Off The notebook is switched off or in Save-to-Disk mode.

22 - Display PanelFigure 7. Hybrid Tablet Display PanelDisplay PanelYour STYLISTIC Q702 Hybrid Tablet contains an LCD display panel that is backlit for easier viewing in bright environments. The slate design of your Hybrid Tablet allows you to easily hold the unit and rotate it 90o, 180o, or 270o in either direction. This display is used as a tablet, much as you would a pad of paper. The tablet can also be used in conjunction with the optional keypad dock to create a traditional notebook form.Adjusting Display Panel BrightnessTo adjust brightness with the power management utility:Click Start -> Control Panel. In View by:, select one of the icon views. Select Display, then click Adjust brightness in the left pane. Under Select a power plan, select the plan settings you want to use. Drag Screen brightness: bar (at the bottom of the window) to the left or right, depending on your preference.

23 - Display PanelHolding the Hybrid Tablet The STYLISTIC Q702 can be held in any of three orientations, depending upon how you would like to use it. There is primary landscape orientation (secondary landscape orientation is non-functional) and primary and secondary portrait orientations. (The orientation nomenclatures reflect those used in the button utility). When you rotate the system using the Rotation button, the order in which it rotates is illustrated below. Primary Landscape Orientation Secondary Portrait Orientation Secondary Landscape Orientation(Non-functional) Primary Portrait OrientationSec 3_Display.fm Page 23 Tuesday, August 14, 2012 4:47 PM

24 - Active Digitizer/TouchscreenActive Digitizer/Touchscreen Active Digitizer DisplayThe integrated active digitizer allows you to use the included stylus (also called a “pen”) as a pointing device. (For detailed information about caring for your stylus, go to “Caring for the Pen” on page 30.) You can use the stylus to click, double-click, drag items and icons, write text, or to draw like a pen or pencil in applications that support this behavior, such as drawing or painting programs. See the documentation that came with your application for details.Figure 8. Using the Active Digitizer Display•DO NOT USE EXCESSIVE FORCE WHEN TAPPING OR WRITING ON THE SCREEN WITH THE STYLUS. EXCESSIVE FORCE COULD RESULT IN DAMAGE TO THE LED AND/OR ACTIVE DIGITIZER.•TO PURCHASE ADDITIONAL OR REPLACEMENT STYLUSES, VISIT THE FUJITSU ACCESSORIES WEBSITE AT: WWW.SHOPFUJITSU.COM.

25 - Active Digitizer/TouchscreenClicking on Active Digitizer Display To left-click, touch the object you wish to select and then lift the stylus tip immediately. Figure 9. Clicking on the Active Digitizer DisplayFigure 10. Right-clicking Active DigitizerRight-Clicking on Active Digitizer Right-click can be accomplished by holding the front of the toggle button down while tapping on the screen. To change the settings for the right-click feature, go to Start -> Control Panel -> Pen and Touch. In the Pen Options tab, select “Press and Hold” then click the [Settings] button.

26 - Active Digitizer/TouchscreenDouble-Clicking To double-click, touch the item twice, and then immediately remove the stylus tip. Figure 11. Double-clicking the DisplayDragging Dragging means moving an item with the stylus by touching the screen, moving and then lifting the stylus. To drag, touch the Active Digitizer Display with your stylus on the item you wish to move. While continuing to touch the screen with the stylus, drag the item to its new location by moving the stylus across the screen, and then lifting the stylus to release it. Figure 12. Dragging on the Display

27 - Active Digitizer/TouchscreenCalibrating the Display In order to ensure accurate tracking between the stylus and cursor, you must run the Calibration Utility before you use the system for the first time, or after you change the display resolution.To run the calibration utility:1Go to Start -> Control Panel. 2Double-click the Tablet Settings icon and select the Display tab3Click the [Calibrate] button, then select whether you want to calibrate pen input or touch input.4Adjust the display of your Hybrid Tablet to a comfortable angle and find the (+) symbol in the upper-left corner of the display.5Using the stylus or your finger (depending upon which type of input you are calibrating), firmly touch the screen directly on the (+) symbol. Lift the stylus from the screen and the target will move to a different location on the screen.6Repeat step 5 until you have selected all of the (+) symbols.7Once you have selected all the symbols, press the [OK] button. 8Touch the stylus to various points on the screen to verify that the screen is correctly calibrated. If you are not satisfied with the screen’s calibration, press the [Calibrate]) button to begin again.DO NOT USE EXCESSIVE FORCE WHEN TAPPING ON THE SCREEN DURING CALIBRATION. USE OF EXCESSIVE FORCE COULD RESULT IN DAMAGE TO THE LED AND/OR TOUCH PANEL.

28 - Active Digitizer/TouchscreenUsing the Capacitive TouchscreenCertain configurations of this Hybrid Tablet have an optional dual digitizer that allows you to use either the stylus or your finger(s) as a pointing device. This type of display also allows you to use “gestures” to perform such actions as scroll, zoom, and rotate.Right-clicking the touchscreen To perform a right-click action using two fingers, press the first finger at the location you want to perform a right-click, then quickly tap and release the second finger on the screen.Gesture Mode To initiate gesture mode, two fingers must touch the screen within 200 ms of each other. If the second finger touches the screen after 200 ms has elapsed, the second finger is ignored. If more than two fingers touch the screen in that time, Advanced Gesture Mode is activated instead. When Gesture Mode is activated, no cursor movement is sent to the system.When both fingers are removed, Gesture mode ends. When a third finger is added, gesture mode ends and Advanced gesture mode is activated. Note that if a gesture can’t be recognized, no action is taken. In that case, remove both fingers from the screen and try again.Scrolling Gesture To scroll through long documents or on a web page, place both fingers on the screen (one finger quickly followed by the second). If at least one finger has moved at least 3 mm, a scroll is considered. If both fingers are moving in the same direction and parallel (given a tolerance of 5 mm), Scroll Mode is activated. If one finger is stationary, it is not considered a scroll. If either finger is lifted, Scroll Mode is canceled.•GESTURE SUPPORT IS DETERMINED BY THE APPLICATION IN USE.•THE STYLUS TAKES PRECEDENCE OVER FINGER TOUCH. IF THE STYLUS IS WITHIN ACTIVE RANGE OF THE SCREEN, FINGER TOUCH WILL BE DISABLED.•WHEN ONE FINGER IS USED ON THE TOUCHSCREEN, IT BEHAVES IN THE SAME MANNER AS A STYLUS.

29 - Active Digitizer/TouchscreenZoom Gesture The zoom gesture is especially helpful when viewing pictures. To zoom in, place two fingers on the item you want to enlarge (one finger quickly followed by the second), then spread them away from each other.If at least one finger has moved at least 10 mm, a zoom event is considered. If the distance between the fingers has changed by at least 10 mm, and both fingers have stayed on approximately the same line, Zoom Mode is entered. If either finger strays more than 10 mm from the "zoom line" created when the fingers first made contact, the zoom is canceled.To zoom out, place two fingers on the item you want to reduce (one finger quickly followed by the second), then move them towards each other.Rotate Gesture To change the orientation of an object on the screen, place two fingers on the image you want to rotate (one finger quickly followed by the second), then move them in opposite directions (as if you were turning a knob). The direction the item turns is dependant upon the direction you move your fingers.If at least one finger moves at least 12 mm, a rotate is considered. If one finger is stationary (moving less than 5 mm in any direction), and the other is moving, a rotate is considered. If the fingers begin moving in the same direction, the rotation is canceled. If the distance between the fingers changes by more than 10 mm, the rotation is canceled.Accessing the OnScreen TouchPadYour tablet has a handy on-screen touchpad that offers a variety of helpful functions. Features of the OnScreen TouchPad include:•Virtual Mouse Emulator: The Virtual Mouse Emulator works in much the same manner as a hardware mouse. With the virtual mouse, you can scroll, drag, and click, as well as perform [Ctl]+[Click] and [Shift]+[Click] actions.•Application Launch/Key Macro: This window provides access to five pages, each of which can contain up to twenty buttons. Each button can be programmed to open an application, a folder, document, or key (such as [Esc], [ Alt+X] and [Page Up]).•Digital Keyboard: This window provides a soft keyboard for use in mathematical procedures. It works in much the same way as the Windows standard calculator.

30 - Active Digitizer/TouchscreenTo access the OnScreen TouchPad, go to the Start Menu > All Programs > Fujitsu OnScreen TouchPad. To learn more about the utility, click on Usage and Help. Using the Nuance SoftKeyboardFor general information about using the Nuance SoftKeyboard, please refer to your Getting Started Guide that came with the system. If you have questions about the Nuance SoftKeyboard, or you would like to learn more, click the Help icon (it looks like a question mark) in the Nuance taskbar.Caring for the PenChanging the Pen Settings There are a few changes you can make to your pen settings in order to make it more suitable to your needs (such as changing the pressure sensitivity). To do so, go to Start > Control Panel and select one of the icon views from the “View by:” dropdown. Click on the Pen and Touch icon to open the window from which you can change a variety of pen settings.•ONLY USE THE PEN PROVIDED WITH YOUR HYBRID TABLET. DO NOT USE SUBSTITUTE PEN TIPS THAT WERE NOT SPECIALLY DESIGNED FOR YOUR TABLET. REPLACE THE STYLUS TIP IF IT IS WORN. THE WARRANTY DOES NOT COVER A SCRATCHED SCREEN.•WHILE WRITING, DO NOT TO SCRATCH THE SURFACE OF THE DISPLAY (E.G., WITH A WRISTWATCH OR BRACELET).•THE PEN OF YOUR HYBRID TABLET IS AN ELECTRONIC INSTRUMENT WHICH CAN BE DAMAGED IF USED INCORRECTLY. HANDLE THE PEN WITH CARE. THE FOLLOWING LIST CONTAINS GUIDELINES FOR PROPER PEN HANDLING:•DO NOT GESTURE WITH THE PEN OR USE IT AS A POINTER.•NEVER USE THE PEN ON ANY OTHER SURFACE THAN THE SCREEN OF YOUR HYBRID TABLET.•DO NOT TRY TO TURN THE THUMB GRIP ON THE PEN. •NEVER STORE THE PEN WITH THE TIP BEARING THE WEIGHT OF THE PEN. IF THE PEN IS STORED WITH THE TIP POINTING DOWN, THIS MAY HAVE AN ADVERSE EFFECT ON THE PEN MECHANISM (PARTICULARLY UNDER HIGH TEMPERATURES). IN THIS CASE THE PEN TIP MAY REACT AS THOUGH IT IS CONSTANTLY BEING PRESSED DOWN.•THE PEN CAN BE INFLUENCED BY ELECTROMAGNETIC FIELDS (CURSOR QUIVERS OR JUMPS). THERE MAY BE A FEW AREAS ON THE SCREEN WHERE THE CURSOR QUIVERS SLIGHTLY IN SPITE OF PRESSING THE PEN DOWN FIRMLY.

31 - Active Digitizer/TouchscreenChanging the Pen BatteryFigure 13. Replacing the Battery•DO NOT REMOVE THE TIP OF THE PEN TO REPLACE THE BATTERY; REMOVE ONLY THE CAP ON THE TOP OF THE PEN.•THERE IS A RISK OF EXPLOSION IF THE BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES IN ACCORDANCE WITH LOCAL INSTRUCTIONS.The pen contains a AAAA-battery. Before proceeding, be sure to have a new battery available.1Remove the rear Pen Cap (Figure 13).2Remove the battery from the pen barrel.3Insert the new battery into the pen barrel in the same orientation as the one that was removed.4Close the rear Pen Cap.Pen CapAAAA-batteryPen Barrel

32 - Active Digitizer/Touchscreen Replacing the Pen Tip With use, the pen tip may become worn or may pick up foreign particles that can scratch the screen. A damaged or worn tip may not move freely, causing unpredictable results when using the pen. If a problem like this should occur, you should replace the pen tip.1Pull the tip from the barrel.2Using one of the new tips that were supplied with your pen, insert the pointed end of the tip into the barrel and push it in firmly until it is in place Figure 14. Replacing the Pen TipInstalling a Pen Tether To prevent dropping or losing your pen, you should attach it to your system using the pen tether that is included with the system. To attach the pen tether to your Hybrid Tablet, perform the following steps:1Attach the end of the pen tether with the smaller loop to your pen. To do so, push the end of the tether under the slot on the top of the pen, then thread the opposite end of the tether through the loop.2Attach the end of the pen tether with the larger loop to the attachment point on the right side of your tablet. To do so, insert the end of the pen tether through the attachment point, then feed the pen through the large loop in the tether.Figure 15. Installing a Pen TetherPen TipPen Barrel

33 - Hybrid Tablet ButtonsHybrid Tablet ButtonsThe three Tablet buttons are located on the right-hand side of a horizon-tally-oriented system. The Windows button is located at the bottom center of the display.Figure 16. Application buttonsButton Name PrimaryFunction (Press)Press at Splash Screen* In BIOS Setup Utility DescriptionVolume Down Button Volume Down Opens BIOS setup Acts as Down key while in BIOS SetupPressing the Volume Down button decreases the volume. While the system is starting up, it opens the BIOS Setup utility, and while the BIOS is open, it can be used to move the cursor down.Volume Up Button Volume Up None Acts as Up key while in BIOS SetupPressing the Volume Up button increases the volume. When the BIOS is open, it can be used to move the cursor up.Rotation Volume Down ButtonVolume Up Button Lock ButtonWindows Button

35 Chapter 2 Getting Started with Your Hybrid Tablet Power SourcesYour Fujitsu STYLISTIC Hybrid Tablet has three possible power sources: a primary Lithium Polymer battery, an AC adapter or an optional Auto/Airline adapter.Connecting the Power AdaptersThe AC adapter or optional Auto/Airline adapter provides power for operating your Hybrid Tablet and charging the batteries. Connecting the AC Adapter 1Plug the DC output cable into the DC power jack of your STYLISTIC Hybrid Tablet.2Plug the AC adapter into an AC electrical outlet. Connecting the Optional Auto/Airline Adapter 1Plug the DC output cable into the DC power jack on your Hybrid Tablet.2Plug the Auto/Airline adapter into the cigarette lighter of an automobile, or, 3Plug the Auto/Airline adapter into the DC power jack on an airplane seat.

36 - Power SourcesFigure 17. Connecting the AC AdapterSwitching from AC Adapter Power or the Auto/Airline Adapter to Battery Power 1Be sure that you have at least one charged battery installed.2Remove the AC adapter or the Auto/Airline adapter.THE LITHIUM POLYMER BATTERY IS NOT CHARGED UPON PURCHASE. INITIALLY, YOU WILL NEED TO CONNECT EITHER THE AC ADAPTER OR THE AUTO/AIRLINE ADAPTER TO USE YOUR HYBRID TABLET.DC Power JackAC Adapter

37 - Starting Your STYLISTIC Hybrid TabletStarting Your STYLISTIC Hybrid TabletPower OnPower/Suspend/Resume Switch The Power/Suspend/Resume switch is used to turn on your STYLISTIC Hybrid Tablet from its off state. Once you have connected your AC adapter or charged the internal Lithium Polymer battery, you can power on your tablet.WHEN YOU TURN ON YOUR STYLISTIC HYBRID TABLET BE SURE YOU HAVE A POWER SOURCE. THIS MEANS THAT AT LEAST ONE BATTERY IS INSTALLED AND CHARGED, OR THAT THE AC OR AUTO/AIRLINE ADAPTER IS CONNECTED AND HAS POWER.To turn on your STYLISTIC Hybrid Tablet from its off state, slide the Power/Suspend/Resume switch, located on the right side of the tablet (when the system is held horizontally). When you are done working you can either leave your Hybrid Tablet in Suspend mode or you can turn it off. See “Sleep Mode” on page 41 and “Powering Off” on page 43. When you power on your STYLISTIC, it will perform a Power On Self Test (POST) to check the internal parts and configuration for correct functionality. If a fault is found, your STYLISTIC Hybrid Tablet will emit an audio warning and/or an error message will be displayed. See “Power On Self Test Messages” on page 60. Depending on the nature of the problem, you may be able to continue by starting the operating system or by entering the BIOS setup utility and revising the settings.After satisfactory completion of the POST, your tablet will load your operating system.Figure 18. Power/Suspend/Resume Switch

40 - Starting Your STYLISTIC Hybrid TabletDuring the course of the first start up, you will need to read and accept the End User License Agreements (EULAs) for Microsoft and Fujitsu. Several additional windows will appear, prompting you to enter a name and description for your computer, an Administrator password, and a domain name. Read the instructions on the screens carefully and fill in the information as directed. Installing Bonus Apps After you have started your system the first time, you will see a Bonus Apps icon on your desktop. Click on the icon to see which additional applications are available for you to install. Applications that are already installed appear in grey; those that are available for installation appear in blue.Select the applications you wish to install by selecting the checkbox adjacent to your selection, or click [Select All] if you would like to install all available applications. Once you have made your selections, click [Install].Note that in some cases (depending upon which application was selected for installation) after installation completes, the system will prompt you to reboot. There are also cases in which if multiple applications are selected to install but one of them needs a reboot, the system will reboot and continue installing the rest of the selected applications. Registering your Tablet with Fujitsu You can register your tablet by going to our website at: https://store.shopfujitsu.com/fpc/Ecommerce/Service.jsp. You will need to be set up with an Internet Service Provider (ISP) to register online. •IF YOU REJECT THE TERMS OF THE LICENSE AGREEMENT YOU WILL BE ASKED TO REVIEW THE LICENSE AGREEMENT FOR INFORMATION ON RETURNING WINDOWS OR TO SHUT DOWN YOUR TABLET.•YOU CANNOT USE YOUR TABLET UNTIL YOU HAVE ACCEPTED THE LICENSE AGREEMENT. IF YOU STOP THE PROCESS YOUR TABLET WILL RETURN TO THE BEGINNING OF THE WINDOWS WELCOME PROCESS, EVEN IF YOU SHUT YOUR TABLET DOWN AND START IT UP AGAIN.

42 - Power ManagementYour Hybrid Tablet’s system memory typically stores the file on which you are working, open application information, and any other data required to support operations in progress. When you resume operation from Sleep mode, your tablet will return to the point where it left off. You must use the Power/Suspend/Resume switch to resume operation, and there must be an adequate power source available, or your Hybrid Tablet will not resume.Hibernation FeatureThe Hibernation feature saves the contents of your Hybrid Tablet’s system memory to the hard drive as a part of the Suspend/Resume mode. Hibernation is enabled by default. Defining Power Button Action To determine what occurs when the power button is pressed, follow these steps:1From the Start menu, select Control Panel, then select the Power Options icon.2Select “Choose what the power button does”, then make your selections (Do Nothing, Sleep, Hibernate, or Shut Down).Windows Power Management The Power Options icon located in the Windows Control Panel allows you to configure some of the power management settings. For example, you can use the Power Options to set the timeout values for turning off the display and hard disks whether you are running the Hybrid Tablet on battery power or one of the adapters. •IF RUNNING YOUR TABLET ON BATTERY POWER, BE AWARE THAT THE BATTERY CONTINUES TO DISCHARGE WHILE YOUR TABLET IS IN SLEEP MODE, THOUGH NOT AS QUICKLY AS WHEN FULLY OPERATIONAL. •DISABLING THE POWER/SUSPEND/RESUME SWITCH PREVENTS IT FROM BEING USED TO PUT THE TABLET INTO SLEEP OR HIBERNATION MODE. THE BUTTON RESUME FUNCTION CANNOT BE DISABLED.•IF YOUR TABLET IS ACTIVELY ACCESSING INFORMATION WHEN YOU ENTER THE SLEEP OR HIBERNATION MODE, CHANGES TO OPEN FILES ARE NOT LOST. THE FILES ARE LEFT OPEN AND MEMORY IS KEPT ACTIVE DURING SLEEP MODE OR THE MEMORY IS TRANSFERRED TO THE INTERNAL HARD DRIVE DURING HIBERNATION MODE.•THE MAIN ADVANTAGE OF USING HIBERNATION IS THAT POWER IS NOT REQUIRED TO MAINTAIN YOUR DATA. THIS IS PARTICULARLY IMPORTANT IF YOU WILL BE LEAVING YOUR TABLET IN A SUSPENDED STATE FOR A PROLONGED PERIOD OF TIME. THE DRAWBACK OF USING HIBERNATION MODE IS THAT IT LENGTHENS THE POWER DOWN AND POWER UP SEQUENCES AND RESETS PERIPHERAL DEVICES.

43 - Power ManagementRestarting the SystemIf your system is on and you need to restart it, be sure that you use the following procedure. 1Click the [Start] button, and then move the mouse over the small arrow at the bottom right of the right-hand pane.2Select Restart from the list.Powering OffIf you turn off the power while accessing a disk there is a risk of data loss. To ensure that your Hybrid Tablet shuts down without error, use the Windows shut down procedure.Using the correct procedure to shut down from Windows allows your Hybrid Tablet to complete its operations and turn off power in the proper sequence to avoid errors. The proper sequence is:1Click the [Start] button, and then move the mouse over the small arrow at the bottom right of the right-hand pane.2Select Shut Down from the list.If you are going to store your Hybrid Tablet for a month or more, see Care and Maintenance Section on page page 70. TURNING OFF YOUR STYLISTIC HYBRID TABLET WITHOUT EXITING WINDOWS OR TURNING ON YOUR HYBRID TABLET WITHIN 10 SECONDS OF THE SYSTEM BEING SHUT OFF MAY CAUSE AN ERROR WHEN YOU START THE NEXT TIME. BE SURE TO CLOSE ALL FILES, EXIT ALL APPLICATIONS, AND SHUT DOWN YOUR OPERATING SYSTEM PRIOR TO TURNING OFF THE POWER. IF FILES ARE OPEN WHEN YOU TURN THE POWER OFF, YOU WILL LOSE ANY CHANGES THAT HAVE NOT BEEN SAVED, AND MAY CAUSE DISK ERRORS.

44 Chapter 3 User-Installable FeaturesSecure Digital CardsYour STYLISTIC Hybrid Tablet supports Secure Digital (SD) cards, on which you can store and transfer data to and from a variety of digital devices. These cards use flash memory architecture, which means they don’t need a power source to retain data. Note that SD and SDHC Cards are supported, but SDXC Cards are not.SD Cards allow portable storage among a variety of devices, such as cell phones, GPS systems, digital cameras, and PDAs. SD Cards transfer data quickly, with low battery consumption.Figure 19. SD Card Slot - Rear AccessSD CardSD Card Slot

45 - Secure Digital CardsInstalling SD CardsWhen holding the Hybrid Tablet in horizontal position with the bottom side up and the fingerprint sensor at the bottom left, the SD Card slot is located near the DC port on the left side of the system (Figure 19). To install an SD Card, follow these steps:1See your specific card manual for instructions on the installation of your card. Some cards may require that your Hybrid Tablet is off while installing them.2Make sure there is no card currently in the slot. If there is, see Removing an SD Card.3With the product label facing in the same direction as the display screen, insert your card into the slot.4Push the card firmly into the slot until it is seated in the connector. Removing an SD CardTo remove an SD Card, follow these easy steps:1Select Safely Remove Hardware from the System Tray. Highlight the card in the list, then click [Stop].2Push the SD Card in until it unlatches. It will then eject from the slot for removal.INSTALLING OR REMOVING AN SD CARD DURING YOUR STYLISTIC HYBRID TABLET’S SHUTDOWN OR BOOTUP PROCESS MAY DAMAGE THE CARD AND/OR YOUR STYLISTIC HYBRID TABLET.DO NOT INSERT A CARD INTO A SLOT IF THERE IS WATER OR ANY OTHER SUBSTANCE ON THE CARD AS YOU MAY PERMANENTLY DAMAGE THE CARD, YOUR STYLISTIC HYBRID TABLET, OR BOTH.SEE YOUR CARD MANUAL FOR SPECIFIC INSTRUCTIONS ON THE REMOVAL OF YOUR CARD. SOME CARDS MAY REQUIRE YOUR STYLISTIC HYBRID TABLET TO BE IN SLEEP MODE OR OFF WHILE REMOVING THEM.

46 - Keyboard Docking StationKeyboard Docking StationThe optional keyboard docking station extends the functionality of your STYLISTIC® Tablet and turns it into a truly “hybrid” system by providing a keyboard, touchpad, rechargeable and removable battery, status LEDs, two USB 2.0 ports, a LAN port, external monitor port, and DC power. The docking station connects to the bottom edge of your STYLISTIC Hybrid Tablet, and folds up to create a protective cover over the display.Figure 20. Docking Station - Rear Figure 21. Docking Station - FrontDC In USB 2.0 portExternal Monitor ConnectorTablet SupportDocking ConnectorUSB 2.0 portLAN (RJ-45) JackTouchpadPen garageTablet Support Release LatchPen Release

47 - Docking Station ComponentsThe following is a brief description of the docking station’s panel components. (Figures 20 and 21).Tablet Support Release Latch The tablet support on the back of the docking station acts as a support when it is open so that you can use the tablet in a hands-free vertical position and close it as a traditional notebook. To release the panel from the back of the docking station, slide the latch to the right. To attach it to the docking station, set the tablet into the tablet support, then snap the two together.USB 2.0 Ports (Qty. 2) Universal Serial Bus (USB) 2.0 ports allow you to connect USB devices. USB 2.0 ports are backward-compatible with USB 1.1 devices. There are two USB ports on the docking station: one on the left side and one on the right side.DC Power Jack The DC power jack allows you to plug in the AC adapter to power your Hybrid Tablet and charge the internal battery.LAN (RJ-45) Jack The internal LAN (RJ-45) jack is used for an internal LAN connection. External Monitor Connector The external monitor connector allows you to connect an external monitor or LCD projector.Docking Connector The docking connector allows you to connect the Docking Station to your STYLISTIC Hybrid Tablet.Touchpad Pointing Device The Touchpad pointing device is a mouse-like cursor control with two buttons (left and right). THE SYSTEM CONTAINS COMPONENTS THAT CAN BE SEVERELY DAMAGED BY ELECTROSTATIC DISCHARGE (ESD). TO MINIMIZE RISK TO THE COMPONENTS, OBSERVE THE FOLLOWING PRECAUTIONS:•BEFORE DOCKING OR UNDOCKING YOUR STYLISTIC WHEN USING A DOCKING STATION, YOU SHOULD TOUCH A GROUNDED METAL OBJECT TO DISCHARGE STATIC ELECTRICITY BUILT UP IN YOUR BODY.

48 - Pen Garage The pen garage is used to store the pen when it is not in use. This helps you keep track of the pen so it is not misplaced or lost. The pen garage sits directly below the pen tether attachment point when the system is closed while in notebook configuration.Pen Release The pen release is used to eject the pen from the pen garage. Slide the pen release to the left when the pen is in the garage; doing so will cause the pen to pop out of the garage. Attaching the Docking StationTo attach the Docking Station, align the docking connector on the bottom of your Hybrid Tablet with the connector on the Docking Station and push the corners down simultaneously. (Figure 22)Figure 22. Attaching the Docking Station Figure 23. Detaching the Docking StationDocking ConnectorTablet Support Release Latch

49 - Detaching Docking StationTo detach the Docking Station, slide the tablet support release latch to the right and lift the Hybrid Tablet away from the Docking Station to detach it. (Figure 23)Changing the BatteryThe keyboard docking station is equipped with a rechargeable, removable battery. The battery can be charged by connecting the AC Adapter to the DC In port on the left side of the docking station (Figure 20). To remove the battery for replacement with a new battery or when storing the docking station for a long period of time, perform the following steps (Figure 25):1Turn the docking station upside down.2While pushing the battery lock, slide the battery latch to release the battery.3Lift the battery at the lift point and remove it from the battery bay.Figure 24. Docking Station - Bottom Figure 25. Removing the BatteryBattery LockBattery LatchLift Point

50 - Docking Station Status IndicatorsThere are two sets of status indicators on the docking status, one on the left front edge and one on the left back corner.Figure 26. Docking Station Status IndicatorsDocking IndicatorThe docking indicator lights when the tablet is properly seated in the tablet support.Battery Charge IndicatorThe battery charge indicator shows the charging status of the keyboard dock battery. (See Table 1 on page 21 for equivalent system indicator states).Docking IndicatorBattery ChargingBattery LevelNum LockCaps LockScroll Lock

51 - Battery Level IndicatorThe Battery Level indicator displays the charge level of the keyboard dock battery pack. (See Table 1 on page 21 for equivalent system indicator states).NumLk IndicatorThe NumLk indicator shows that the integral keyboard is set in ten-key numeric keypad mode. CapsLock IndicatorThe CapsLock indicator shows that your keyboard is set to type in all capital letters. ScrLk IndicatorThe ScrLk indicator shows that your scroll lock is active.

52 Chapter 4 Troubleshooting Your Hybrid TabletTroubleshootingThere may be occasions when you encounter simple setup or operating problems that you can solve on the spot, or problems with peripheral devices that can be solved by replacing the device. The information in this section helps you isolate and resolve some of these straightforward issues and identify failures that require service.Identifying the ProblemIf you encounter a problem, go through the following procedure before pursuing complex troubleshooting:1Turn off your STYLISTIC Hybrid Tablet.2Make sure the AC adapter is plugged into your Hybrid Tablet and to an active AC power source.3Make sure that any cards installed are seated properly. If it appears that there is a problem with a card, remove the card from the slot, thus eliminating it as a possible cause of failure.4Make sure that any devices connected to the external connectors are plugged in properly. You can also disconnect such devices, thus eliminating them as possible causes of failure.5Turn on your Hybrid Tablet. Make sure it has been off at least 10 seconds before you turn it back on.6Go through the boot sequence.7If the problem has not been resolved, refer to the Troubleshooting Table that follows for more detailed troubleshooting information.

53 - Troubleshooting8If you have tried the solutions suggested in the Troubleshooting Table without success, contact your support representative: Toll free: 1-800-8FUJITSU (1-800-838-5487) Web site: http://solutions.us.fujitsu.com/www/content/support/contact/index.php.Before you place the call, you should have the following information ready so that the customer support representative can provide you with the fastest possible solution:•Product name•Product configuration number•Product serial number•Purchase date•Conditions under which the problem occurred•Any error messages that have occurred•Type of device connected, if anySee the Configuration Label on the bottom of your Hybrid Tablet for configuration and serial numbers. IF YOU KEEP NOTES ABOUT WHAT YOU HAVE TRIED, YOUR SUPPORT REPRESENTATIVE MAY BE ABLE TO HELP YOU MORE QUICKLY BY GIVING ADDITIONAL SUGGESTIONS OVER THE PHONE.

54 - TroubleshootingSpecific ProblemsUsing the Troubleshooting Table When you have problems with your Hybrid Tablet, try to find the symptoms under the Problem column of the troubleshooting table for the feature giving you difficulty. You will find a description of common causes for that symptom under the column Possible Cause and what, if anything, you can do to correct the condition under Possible Solutions. All possible causes or solutions may not apply to your Hybrid Tablet. Troubleshooting TableAudio Problems. . . . . . . . . . . . . . . . . .page 55Hard Drive Problems. . . . . . . . . . . . . .page 55Keyboard or Mouse Problems. . . . . . .page 55Pen Input Problems . . . . . . . . . . . . . .page 55USB Device Problems . . . . . . . . . . . . .page 56Power Failures. . . . . . . . . . . . . . . . . . . page 56Shutdown and Startup Problems . . . . page 58Video Problems. . . . . . . . . . . . . . . . . . page 59Miscellaneous Problems. . . . . . . . . . . page 59

55 - TroubleshootingProblem Possible Cause Possible SolutionsAudio ProblemsThere is no sound coming from the built-in speaker.The volume is turned too low. Adjust the volume control on your Hybrid Tablet and operating system. Click the Vol-ume icon in the system tray on the bottom right of the screen. (It looks like a speaker). If the Mute box has a red circle on it, click on it to deselect it. Headphones are plugged into your tablet.Plugging in headphones disables the built-in speaker. Remove the headphones.Hard Drive ProblemsYou cannot access your hard drive.The wrong drive designator was used by an application when a bootable disc was used to start the Hybrid Tablet.Verify drive designator used by application is in use by the operating system. When the operating system is booted from a CD, drive designations are automatically adjusted. Security is set so your operating system cannot be started with-out a password.Verify your password and security settings.Keyboard or Mouse ProblemsYou have installed an optional external keyboard or mouse, and it does not seem to work.Your external device is not prop-erly installed.Re-install your device. See “Device Ports” on page 82.Your operating system is not set up with correct software driver for that device.Check your device and operating system documentation and activate the proper driver.You have connected an external keyboard or a mouse and it seems to be locking up the system.Your operating system is not setup with correct driver.Check your device and operating system documentation and activate the proper driver.Your system has crashed. Try to restart your Hybrid Tablet. Pen Input ProblemsCursor is not tracking the pen.Display needs to be calibrated See “Calibrating the Display” on page 27. for more information.

56 - TroubleshootingTablet is not responding to the penSystem may have crashed. If the Hybrid Tablet does not respond to the pen, connect an external keyboard to the system to see if it responds to keyboard commands. If the system doesn’t respond to a keyboard, the application or system may have crashed, and it may be necessary to reboot the system. If the system responds to a keyboard but not to a pen, contact your local help desk or reseller, or call Fujitsu Service and Support at 1-800-8Fujitsu (1-800-838-5487) for further assistance.Memory ProblemsYour System screen in the Control Panel doesn’t show correct amount of memory.You have a memory failure. Check for Power On Self Test (POST) messages. See “Power On Self Test Messages” on page 60. USB Device ProblemsYour system doesn’t recog-nize a USB device you installed, or the device doesn’t work properly.The device is not properly installed.Remove and re-install the device.The device may have been installed while an application was running, so your system is not aware of its installation.Close the application and restart your Hybrid Tablet.Your device may not have the correct software driver active.See your software documentation and activate the correct driver.Power FailuresYou turn on your Hybrid Tab-let and nothing seems to happen.The installed battery is com-pletely discharged or there is no power adapter installed.Check the Status Indicator Panel to determine the presence and condition of the bat-tery. See “Status Indicator Panel” on page 20. Install a charged battery or a Power adapter.The battery is installed but is faulty or very low.When the battery reaches a critically low level, the system is forced into Sleep mode to avoid a total system power failure. To correct this problem, either connect an exter-nal power supply (such as the AC adapter), or install a charged battery in the tablet. System is at a critical thermal limit.To avoid damage to heat-sensitive components, the system enters sleep mode when it gets too hot. System operation cannot be resumed until the Hybrid Tablet cools off to a tolerable temperature. Move the Hybrid Tablet to a cooler location.Problem Possible Cause Possible Solutions

57 - TroubleshootingYou turn on your Hybrid Tab-let and nothing seems to happen. (continued)AC power adapter is not plugged in properly.Verify that your adapter is connected correctly. See “Power Sources” on page 35.The power adapter has no power from the AC or airline outlet.Move the AC cord to a different outlet, or check for a line switch or tripped circuit breaker. If you are using an auto/airline adapter in a car be sure the ignition switch is in the On or Accessories position.The power adapter is faulty. Try a different power adapter.Your STYLISTIC Hybrid Tablet turns off all by itself.The power management param-eters are set for auto timeouts which are too short for your operating needs.Move the mouse to restore operation. If that fails, push Power/Suspend/Resume switch. Check your power management settings, or close your applications and go to Power Options located in the Control Panel to adjust timeouts to better suit your needs.Your power adapter has failed or lost its power source.Make sure the adapter is plugged in and the outlet has power.You ignored a low battery alarm until the battery entered Dead Battery Suspend mode.Install a power adapter, then push the Power/Suspend/Resume switch. See “Power Sources” on page 35.You have a battery failure. Verify the condition of the battery using the Status Indicator panel. If the battery is shorted, replace or remove it. See “Status Indicator Panel” on page 20.Your Hybrid Tablet will not work on battery alone.The installed battery is dead. Replace the battery with a charged one or use an adapter.No battery is installed. Install a charged battery.Battery is improperly installed. Verify that the battery is properly connected by re-installing it.Your installed battery is faulty. Verify the condition of the battery using the Status Indicator panel and replace or remove any batteries that are shorted. See “Status Indicator Panel” on page 20.The battery seems to discharge too quickly.The power savings features may be disabled.Check the Power Options menu settings and adjust according to your operating needs.The brightness is turned all the way up.Turn down the brightness adjustment. The higher the brightness the more power your display uses.Problem Possible Cause Possible Solutions

59 - TroubleshootingVideo ProblemsThe display is blank when you turn on your Hybrid Tab-let.Power management timeouts are set for short intervals and you didn’t see the display go on and off again.Move the mouse to restore operation. If that fails, push the Power/Suspend/Resume switch. (The display may be shut off by Sleep mode, Auto Suspend or Video Timeout)The Hybrid Tablet turned on with a series of beeps and the display is blank.Power On Self Test detected a failure which does not allow the display to operate. Contact your support representative.The display goes blank by itself after you have been using it.Power management timeouts are set for short intervals and you failed to notice the display come on and go off again.Push the Power/Suspend/Resume switch. (The display may be shut off by Sleep Mode, Auto Suspend or Video Timeout)The Hybrid Tablet has gone into Sleep or Hibernate mode because you have not used it for a period of time.Push Power/Suspend/Resume switch. Check power management settings, or close applications and go to the Power Savings menu of the setup utility to adjust timeout values to suit your needs. See “BIOS Setup Utility” on page 38.The display has bright or dark spots.If the spots are very tiny and few in number, this is normal for a large LCD display.This is normal; do nothing.If the spots are numerous or large enough to interfere with your operation needs.Display is faulty; contact your support representative.Miscellaneous ProblemsError message displayed on the screen during operation of an application.Application software often has its own set of error message dis-plays. See your application manual and help displays screens for more information. Not all messages are errors some may simply be status.Problem Possible Cause Possible Solutions

60 - TroubleshootingPower On Self Test MessagesThe following is a list of error-and-status messages that the Phoenix BIOS and/or your operating system can generate and an explanation of each message. Error messages are marked with an *. If an error message is displayed that is not in this list, write it down and check the operating system documentation on screen and in the manual. If you can find no reference to the message, contact a support representative.*Invalid NVRAM Data Problem with NVRAM access. In the unlikely case that you see this message you may have a display problem. You can continue operating but should contact your support representative for more information.*Operating system not found Operating system cannot be located on either drive A: or drive C: Enter the setup utility and see if both the fixed disk, and drive A: are properly identified and that the boot sequence is set correctly. Unless you have changed your installation greatly, the operating system should be on drive C:. If the setup utility is correctly set, your hard drive may be corrupted.*Real time clock error - Check date and time settings Real-time clock fails BIOS test. May require board repair. Contact your support representative.

61 - Restoring Your System Image and SoftwareRestoring Your System Image and SoftwareIt is very important that you create DVD copies of your Factory Image and Bootable Disc (along with other applicable media such as application discs) before beginning to use your system. To do so, follow the instructions in the “Saving Your Factory Image” and “Creating Backup Images of Factory Image and Discs” sections of this chapter.Saving and Recovering Your Factory and System ImagesAlong with instructions on saving your Factory Image, this document outlines several other important procedures, such as making a system image, restoring your Factory Image and system images, managing your images, and restoring the partitions on a hard drive. Saving your Factory Image When you purchased your new system, a copy of the pre-installed Factory Image was loaded into a hidden partition on your hard disk drive. Having a copy of the original Factory Image available to you means that in the event of system failure, you will be able to restore it to its original state.•IN ORDER TO INSTALL APPLICATIONS, MAKE COPIES OF FACTORY AND SYSTEM IMAGES, AND BURN APPLICATION MEDIA AND BOOTABLE DISCS YOU MUST HAVE AN EXTERNALLY CONNECTED WRITABLE DVD DRIVE.•IT IS EXTREMELY IMPORTANT THAT YOU COPY YOUR FACTORY IMAGE TO REMOVABLE MEDIA (E.G., DVD DISCS). FAILURE TO DO SO COULD RESULT IN AN INABILITY TO RESTORE THE IMAGE AT A FUTURE DATE.•WE RECOMMEND THAT YOU USE DVD-R OR DVD+R DISCS FOR YOUR BACKUP, BUT SUPPORTED MEDIA* FOR IMAGE BACKUPS INCLUDE: FOR FACTORY IMAGE, APPLICATION DATA, AND BOOTABLE DISC: DVD-R/+R. FOR USER-CREATED BACKUP IMAGE: DVD-R/+R, DVD-RW/+RW, DVD-DL. * DEPENDING UPON YOUR OPTICAL DRIVE AND MEDIA FORMAT USED, SOME MEDIA TYPES MAY BE INCOMPATIBLE FOR CREATING IMAGE BACKUPS. DUE TO CERTAIN LICENSING REQUIREMENTS, SOME THIRD-PARTY APPLICATIONS WILL NEED TO BE INSTALLED SEPARATELY USING THE APPLICATION MEDIA BUNDLED WITH YOUR SYSTEM.

62 - Restoring Your System Image and SoftwareTo make a copy of the Factory Image to DVD discs, you will need several blank discs (DVD-R or DVD+R discs are recommended) to create the copy. After creating the copy, be sure to label the discs and keep them in a safe place to ensure they do not get damaged.Creating Backup Images of Factory Image and Discs Using the [Manage/Change] button, you can create backup images of the Factory Image, Application Disc(s), or Bootable Disc.1Launch My Recovery from desktop icon2Select [Manage/Create]-> [Manage Backup Images]. The Backup Images menu displays a list from which you can choose which type of disc you want to burn: Bootable Disc, Application Discs, or Recovery Disc.3Select Recovery Disc, then click [Make DVD].4Confirm that the # box has “2” (Note that in some cases the box may display a larger number for the factory image, depending upon its size.)5The message “Recovery Disc #1 will be created. Enter your comments and the number of media on the DVD”. Click [YES] to burn the Factory Image.6While the copy is being made, a “Writing to the media screen displays a progress bar. When the copy is complete, a dialog will appear informing you of the successful completion of the backup.7Repeat the process for the remaining images on disc (Bootable Disc and Application Discs). The number of images available may vary depending on your system model; some models do not have the applications loaded on the hard drive.•SOME CONFIGURATIONS OF CERTAIN MODELS DO NOT HAVE APPLICATIONS LOADED ON THE HARD DRIVE; RATHER, THEY ARE AVAILABLE AT THE FUJITSU SUPPORT SITE FOR DOWNLOAD. PLEASE TAKE THAT INTO ACCOUNT WHEN READING THE FOLLOWING PROCEDURES.•ALL USER-CREATED DATA WILL BE DELETED FROM YOUR SYSTEM WHEN THE FACTORY IMAGE IS RESTORED.

$63 - Restoring Your System Image and SoftwareRecovering Your Factory Image In the event you need to restore your original Factory Image, perform the following steps. Note that there may be some third-party applications that need to be installed from the application media bundled with your system.In order to recover your Factory Image, perform the steps outlined in “Running Recovery and Utility from hard disk”. Backing Up a System ImageOptional Step: Launch the Fujitsu Bonus Apps utility from your desktop, and select the components you wish to install.User-Configured System Backups: On your desktop, there is a [MyRecovery] icon that allows you to make backups of your current system image either to another location on your hard drive or on removable media. A system image is the configuration of your C: drive at a particular point of time. You may want to make system image backups occasionally in order to have points to which you can return without having to go all the way back to the Factory Image.By default, system images are saved in the MyRecovery folder (either on D:\ or external hard drive, depending on your hardware type).1Click the [MyRecovery] icon on your desktop. The My Recovery screen will appear (See Figure 27). Note that the screen illustrated may vary, depending upon your system configuration.)2Click the [Backup] button on the MyRecovery screen.3On the next screen that appears, you can enter up to 200 characters of information about the backup file. This information will help you to identify the image at a later date.ALL USER-CREATED DATA WILL BE DELETED FROM YOUR SYSTEM WHEN THE FACTORY IMAGE IS RESTORED.My Recovery$

64 - Restoring Your System Image and SoftwareFigure 27. MyRecovery screen4Click the [Next] button and the system will reboot.5After rebooting, the “Creating of the backup image” window appears, in which you can either click [Create the image on D drive] or [Select the drive] if you want to save to an external hard disk drive. (Note that the [Create the image on D drive may not be available on all configurations.)6An image appears showing you graphically how the image will be stored. Click the [Next] button.7Click [Execute] to start the backup.

65 - Restoring Your System Image and SoftwareManaging Your Backup Images With the MyRecovery tool you can also make copies of backup images, archive them on DVD, or delete them from your hard drive.1To begin, click the [MyRecovery] icon on your desktop.2Click the [Manage/Create] button in the MyRecovery window.3When the MyRecovery Manager window appears, click [Manage Backup Images].4In the next window, a list of your backup images appears. Below the list are three buttons allowing you to [Make DVD], [Copy], or [Delete] your backup images.5Select an image title from the list, then click the action button you would like to perform.6Note that you need to have an external disk drive connected for the [Copy] button to be enabled. If you elect to copy the image, you will be prompted to enter the destination. If you are ready to copy, click [OK] to proceed. A progress screen appears while the backup copy is being made.7Note that if you copy an image to an external hard drive, both the original and the copy will appear in the [Backup Images] window with identical names, dates, and file sizes, but with the different drive letter to distinguish them. Before you select [Make DVD], make sure you have a recordable DVD drive connected and blank DVDs available.Using the Recovery and Utility Tools The Recovery and Utility tools consist of a variety of tools that will help you recover your Factory Image, recover system images, and delete the data from your hard disk.Methods for accessing the utilitiesRecovery and Utility Tools are preinstalled in a hidden partition by the factory, or they can be accessed by using the bootable disc. Please note that you can delete Recovery and Utility tools from your hard disk drive if you modify the partitions. In this case you will not be able to use the hidden partition for booting to Recovery and Utility Tools, but you will still be able to boot from the Bootable Disc.

$66 - Restoring Your System Image and SoftwareDetermining whether Recovery and Utility is pre-loaded1Turn on or reboot your system. When the Fujitsu logo appears, press [F12] key. The Boot Menu will appear.2Press the Tab key to select Application menu. 3Check whether the <Recovery and Utility> option is present. If it is not present, it means that the utility must be used from the disc. Proceed to “Running Recovery and Utility from the Bootable Disc” if <Recovery and Utility> is unavailable.Running Recovery and Utility from hard disk1Turn on or reboot your system. When the Fujitsu logo appears, press [F12] key. The Boot Menu will appear.2Press the Tab key to select Application menu.3Cursor down to <Recovery and Utility> and press the [Enter] key.4While the files are being loaded from the disc, a progress bar will appear at the bottom of the screen.5When the System Recovery Options dialog opens, select a new keyboard layout, if necessary, then click [Next].6When the Operating System dialog appears, select “Use recovery tools...”, then click [Next]. 7If necessary, enter your password, then click [OK].8When System Recovery Options window appears, click on Recovery and Utility.9The Recovery and Utility screen appears on the screen with three tabs: Diagnostics, Recovery and Utility. Please note that Diagnostics tab is not supported on certain LIFEBOOK/STYLISTIC models when running Recovery and Utility from the hard disk. In order to restore the operating system, please use the middle icon “Restoring the Factory Image (only C:\drive)” under the Recovery tab. Running Recovery and Utility from the Bootable discTo verify/change the boot-up priority (rather than booting-up from the hard drive or an external floppy disk drive), perform the following steps:1Power on your system. When the Fujitsu logo appears on the screen. press the [F12] key to get to the Boot Menu. 2Highlight the CD/DVD option.$