Fujitsu Client Computing BPAD05 B-PAD User Manual

Fujitsu Limited B-PAD Users Manual

Users Manual

SAFETY STATEMENT FUJITSU LIMITED 1-1, Kamikodanaka 4-chome, Nakahara-ku, Kawasaki 211-8588, JAPAN Introduction Congratulations on purchasing B-PAD Mobile computer. For your Safety ,please read this statement carefully before using B-PAD. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. End-users must be provided with specific operating instructions for satisfying RF exposure compliance. JUL. 2007 Second Edition Standard for the FCC/IC conformity This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is required to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/television technician for help. This device complies with Part 15 of FCC Rules and RSS-Gen of IC Rules. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of this device. This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. The available scientific evidence does not show that any health problems are associated with using low power wireless devices. There is no proof, however, that these low power wireless devices are absolutely safe. Low power Wireless devices emit low levels of radio frequency energy (RF) in the microwave range while being used. Whereas high levels of RF can produce health effects (by heating tissue), exposure to low-level RF that does not produce heating effects causes no known adverse health effects. Many studies of low-level RF exposures have not found any biological effects. Some studies have suggested that some biological effects might occur, but such findings have not been confirmed by additional research. B-PAD has been tested and found to comply with FCC/IC radiation exposure limits set forth for an uncontrolled equipment and meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65 and RSS-102 of the IC radio frequency (RF) Exposure rules FCC WARNING Change or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. CE marking (1999/5/EC) This product follows the provisions of the European Directive 1999/5/EC. RF Devices Fujitsu’s RF products are designed to be compliant with the rules and regulations in the locations into which they are sold and are labeled as required. The majority of Fujitsu’s RF devices are type approved and do not require the user to obtain license or authorization before using the equipment. Any changes or modification to Fujitsu equipment, not expressly approved by Fujitsu, could void the user’s authority to operate the equipment. Laser Devices This product contains a Class 2 laser and complies with US 21CFR1040.10. These type of lasers use a low power visible light diode. Care should be taken to avoid staring directly into the light. Laser power up to 1.2 mW at 650nm could be accessible in the interior. “CAUTION – Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous laser light exposure.” WARNING – Do not looking into the reading aperture while a scanning beam is being emitted. Doing so can injure the eyes. CAUTION: LASER When using the laser scanner, do not direct the laser beam toward anyone’s eyes. Doing so may injure the eyes. Do not look into the aperture of the laser scanner. Because a laser beam is emitted from the aperture, you may injure your eyes. Scanner Safety Labeling KD91316-L194
WARNING GENERAL INHIBITION Use only the specially designed cradle, AC adapter, and single-pack charger. If another item is used, differences in voltage or current can damage the B-PAD. If the battery is not handled correctly , the B-PAD may overheat, explode, or catch fire. Be sure to observe the following precautions. -Neither throw the battery into a fire or heat it. -Connect the terminals correctly. -Do not connect the terminals using a wire or other metal material. -Do not carry or store the battery with any metal materials, such as necklaces or hair pins. -Do not puncture the battery with a needle, hit it with a hammer, stomp on it, or otherwise apply a strong shock to it. -Do not disassemble or modify the battery. -Do not use or leave the battery near a flame, fire, stove, or other source of heat, in direct sunlight, or in a car exposed to sunlight. -Do not put the battery in a microwave oven or other hot container. -Charge the battery only on the special cradle or single-pack charger. -Do not charge the battery by directly connecting it to a wall outlet or cigarette lighter in a car. -Do not charge the battery near a flame, fire or under the blazing sun. -Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer's instructions. FIRE If the B-PAD generates heat, smoke, or an usual smell or noise, turn off the power immediately and contact maintenance personnel. Failure to do so may result in an electric shock or fire. DISASSEMBLYPROHIBITED Do not modify the B-PAD without permission. Doing so may result in an electric shock or fire. Do not disassemble or remove any components as this will emit laser beams. Maintenance involving the B-PAD internal functions is not necessary. Warning Indications and Symbols This note uses warning indications and symbols to help users use the B-PAD safely and to prevent personal injury and property damage. This manual uses warning indications and symbols in the text to indicate safety conditions. The meaning of each indication and symbol is explained below. Warning Indications Warning Symbols ELECTRIC SHOCK Indicates the possibility of injury from an electric shock. GENERAL INHIBITION Indicates a condition that requires caution and a specific action that must not be performed. GENERAL CAUTION Indicates a condition that requires general caution. FIRE Indicates the possibility of an electric shock or fire. DISASSEMBLYPROHIBITED Indicates an action that is prohibited (prohibited action). UNPLUG THE CABLE Indicates a required action. WARNING Indicates a hazardous situation that could result in personal injury if the user does not perform the procedure correctly. CAUTION Indicates a hazardous situation that could result in minor or moderate personal injury if the user does not perform the procedure correctly. Also indicates that damage to the product or other property could occur if the user does not perform the procedure correctly.
B-PAD Controls and Switches Thank you for purchasing the B-PAD. This guide shows the major operator controls and their use, provides information on charging and replacing the main battery, lists some basic troubleshooting information, and offers procedures to be followed and actions to be avoided. We recommend that you keep this guide with the B-PAD For complete operating instructions and specific RF guidelines, refer to the manuals available on the B-PAD support CDROM, which is available by request from your local Fujitsu Services representative. Attention: Before Using the B-PAD Before using the B-PAD for the first time, the main battery must be fully charged. A new main battery will take approximately 2.5 hours to charge. Replacing / Installing the Main Battery Replace the battery when its performance begins to degrade substantially (approximately 500 cycles). 1. Make sure the backup battery has a sufficient charge to hold the contents of RAM. 2. Turn the unit off, press the power key. 3. Turn over the device. 4. On the rear side, slide the battery lock switches on both sides of the lower part to the outside. 5. Slide the cover down to remove it. 6. Pull the black ribbon to remove the battery. 7. Install a new battery, replace the cover and close both locks. Charging the Battery As the battery charge falls below a certain level, a message prompting you to recharge the battery will appear on the screen. You can charge the battery by mounting the B-PAD on the cradle with the main battery installed in the B-PAD, connect the AC adapter to either of the cradle connection ports and plug the AC adapter into the wall outlet. The battery can also be charged by using the external battery pack charger. Charging Cradle MSR To mount and remove B-PAD from cradle, follow these steps: Scanner LED 1. To mount, place B-PAD onto cradle and rock back until it clicks. 2. To remove, lightly hold the B-PAD with one hand. Using the other hand, press the Eject button in the centre of the cradle. When the Trigger Buttons B-PAD is released from the cradle, hold it lightly and lift it. Operator Controls (Default Configuration Only) Power Switch Function Key Navigation Keys Press the power key to turn the power on. Hold the switch down until green light (located top, centre) turns on. To turn the unit off, press the power key again. Adjusting the Volume Microphone Press the [SFT] + [ENT] key to bring up the [System Information] window. Next tap [1. Volume and Brightness settings] or press the [1] key. Tap arrows [<] [>] within Volume box (or drag meter) to select volume. Adjusting Brightness of back-light Press the [SFT] + [ENT] key to bring up the [System Information] window. Next tap [1. Volume and Brightness settings] or press the [1] key. Tap arrows [<] [>] within Front light box (or drag meter) to select brightness. Correcting the Co-ordinates on Touch Screen Press the [SFT] + [ENT] key to bring up the [System Information] window. Next tap [2. Touch Screen Calibration] or press the [2] key. Follow instructions on screen to perform calibration. When “Calibration settings have been measured” is displayed, press the [ENT] key to save. To cancel operation press [SFT] + [CLR]. Using the Screen Keyboard Open and close the screen keyboard as follows: 1. To open the screen keyboard, press [SFT] + [0] key. The keyboard appears on the lower part of the screen. 2. To close the screen keyboard, press [SFT] + [0] key. To input a character, tap the input field to make it ready for input (the cursor is displayed). Then tap a character. Checking the Battery Status Press the [SFT] + [ENT] key to bring up the [System Information] window. This will then display the main and backup battery charge status. Power Switch Speaker Battery Cover Smart Card Slot Headset Jack Scanner Window Function Key
Smart Card Insertion (Smart Card Rdr Version Only) Chip cards should be inserted into the slot with the chip facing upwards. On EMV-enabled B-Pads, chip card insertion/removal will activate/deactivate the EMV kernel. WARNING: RF Exposure Guidelines The radio module in this device has been approved to CE & R&TTE requirements. The B-PAD contains an internal low-power radio whose radiated output power is far below the CE radio frequency exposure limits. Nevertheless, the B-PAD shall be used in such a manner that the potential for human contact with the radio antenna during normal operation is minimised. The B-PAD should be utilised/worn in accordance with the instructions for the device. This device must not be collocated with any other antenna or transmitters. Bar Code Scanner (application dependent) To use the bar code scanner, follow these steps: 1. Aim the bar code scanner of the B-PAD at a bar code. 2. Press one of the trigger buttons on the sides of the B-PAD. 3. Run the scanning beam across the bar code. 3. The LED lights in green if the data has been read. The scanning beam automatically stops when reading is complete. 5. Release the trigger button. Note: The LED and audio can be used by an application when a bar code is read correctly. To clean the reading aperture use a dry cloth or a cloth moistened with water or diluted neutral detergent solution. Magnetic Card Reader (application dependent) To use magnetic card reader, follow these steps: 1. After making sure of the orientation (direction of the arrow) insert a magnetic card (mag-stripe facing top of B-PAD). 2. Slowly move the magnetic card from left to right. Note: The LED and audio can be used by an application when a magnetic card is read correctly. Clean the reader every month or whenever errors occur frequently with the cleaning card supplied as follows: 1. Turn off B-PAD. 2. Insert the cleaning card in the reader with the rough side facing up. 3. Slowly move the card from left to right. Troubleshooting Symptom User Response Power does not come on. Main battery has no charge. Charge main battery or replace it with a charged main battery. If the main battery is completely dead, all the data and information in memory may be lost. If data has been lost, reinstall the applications again. The service life of the main battery has expired or the battery is faulty. Install a new battery. The main battery may not be installed correctly. Install the main battery correctly. The battery lock switch may be unlocked. Lock it. The screen appears for a moment, then turns black when you press the Power key to turn on the power. The main battery may have no charge. Replace it with a charged main battery. The speaker is silent. The speaker may be set to “low”. Check the volume setting of the speaker. The touch panel does not respond. The co-ordinates on the touch panel may be misaligned. Perform touch panel calibration. B-Pad shows a blank screen when a card is inserted in the Chip card slot EMV-enablement has not been loaded (i.e. Emvelink EMV Level 2 software Quick Reference Guide Fujitsu Services Limited Lovelace Road, Bracknell Berks, RG12 8SN, United Kingdom. Tel: +44 (0) 870 242 7998 Fax: +44 (0) 870 234 6107 Email: askfujitsu@uk.fujitsu.com Web: uk.fujitsu.com Copyright @ Fujitsu Services Limited, 2006 Printed in England 08/06

Navigation menu