Freescale Semiconductor 1323X-MRB Developer Board User Manual 1323xDHRM

Freescale Semiconductor, Inc. Developer Board 1323xDHRM

Contents

User Manual 2

1323x Remote Control Motherboard1323x Development Hardware Reference Manual, Rev. 1.0 Freescale Semiconductor 4-7Again referring to Figure 4-3, a number of zero-ohm resistors are provided to isolate different circuits and to allow current measurement:• VCC (main 1323x-RCM supply) - resistor R35 • V_LED (all LEDs supply) - resistor R36• V_TPD (touchpad supply) - resistor R37• V_ACC (accelerometer supply) - resistor R40• V_BUZ (buzzer supply) - resistor R42• V_MRB (1323x-MRB supply) - resistor R434.2.2 GPIO Connection to 1323x-MRBIO Connectors J8 and J9 (see Figure 4-1) are receptacles that accept the 1323x-MRB pin headers to mount the daughter card. Figure 2-1 shows the 1323x-RCM with the 1323x-MRB mounted. Receptacles J8 and J9 connect to the MC13233 GPIO.To provide better access and versatility to the GPIO, a secondary set of pin headers P1 and P2 is connected in series with the IO signals:• Jumpers must be installed on P1 and P2 to connect 1323x-RCM peripherals and functions• The pin headers provide direct access for connecting custom circuitry to the GPIO• Power and ground to primary connectors J8 and J9 are not enabled though the pin headersFigure 4-4 shows IO Header P1 andP2 pin mapping.External DC Supply 1x2 Pin Header J142.3 V - 6 V The input voltage range is determined by the U8 regulator and the diode isolation circuitTwo AA Batteries Battery Holder 2.0 V - 3.1 V1 • The input voltage range reflects the usable range of alkaline cells and the voltage drop incurred by the diode isolation circuit. • The battery source is disabled if another source is connected1The minimum operating battery voltage is determined by use model, see Note, Section 4.2.1, “Power Management”Table 4-2. 1323x-RCM Voltage SourcesSource Connector Input Voltage Range Description
1323x Remote Control Motherboard1323x Development Hardware Reference Manual, Rev. 1.0 4-8 Freescale SemiconductorFigure 4-4. 1323x-RCM IO Connector J8 and J9 Pin MappingTable 4-3 list the P1 and P2 pin header function as it relates to the MC13233.Table 4-3. 1323x-RCM P1 and P2 Pin Header Function Description1323x-REMHeader PinsMC13233Signal Name Description 1323x-REM Application / NotesP1-27, P1-28 PTA0/XTAL_32K Port A Bit 2 / 32.768 kHz oscillator output • Drives LED1; jumper required • 32.768 kHz oscillator can be enabled on MRBP1-25, P1-26 PTA1/EXTAL_32K Port A Bit 3 / 32.768 kHz oscillator input • Drives Buzzer; jumper required • 32.768 kHz oscillator can be enabled on MRBP1-13, P1-14 RESET Device asynchronous hardware reset. Active low. Onboard Pullup • Drives touchpad reset; jumper required • Reset signal driven from MRBP1-29, P1-30 PTA2 Port A Bit 2. Onboard pull-down for TM • Drive LCD_CTL0; jumper required • Application is LCD enable clock • TM enableP2-13, P2-14 PTA3/IRQ Port A Bit 3 / IRQ. • Used; jumper required • Provides interrupt request input IRQ (active low) from accelerometer and touchpadP2-17, P2-18 PTA4/XTAL_32KOUTPort A Bit 4 / Buffered 32.768 kHz clock output • Drives LED2; jumper required • Optional 32.768 kHz output clock for measuring reference oscillator accuracy (ppm)P1-19, P1-20 PTA5/SDA Port A Bit 5 / IIC Bus data • Used; jumper required • Connects to accelerometer • Defaults to open drain for IIC • Pullup on MRBP1-23, P1-24 PTA6/SCL Port A Bit 6 / IIC Bus clock • Used; jumper required • Connects to accelerometer • Defaults to open drain for IIC • Pullup on MRBP2-1, P2-2 PTB0/KBI1P0 Port B Bit 0 / KBI1 Input Bit 0 RCM switch matrix; jumper requiredP2-3, P2-4 PTB1/KBI1P1 Port B Bit 1 / KBI1 Input Bit 1 RCM switch matrix; jumper required MRB-SPI _MI SOMRB-U AR T_TXDMRB- KBI 2P2MRB- KBI 2P0MRB-SPI_SSMRB-SPI _MOSIMRB-PTA2/LCD_CTL0LCD_CTL0MRB- PTD1/ TPM1MRB- KBI 1P1MRB- KBI 1P3MRB- KBI 1P4MRB- KBI 1P2UART_TXDMRB- PTD3/ TPM3LED1 MRB-PTA0MRB- PTD4/ CMTMRB- KBI 1P5BUZZER MRB-PTA1 MRB-KBI 2P3IRQbMRB- KBI 1P0MRB- KBI 2P1SPI_CLK MRB -SPI_C LKUART_RXD MR B-U ART_R XDMRB- KBI 1P6MRB-PTA4/32K_OUTRSTb MRB-R STb MRB-PTA3/I RQbLED3 MR B-TPM01 23 4657 891011 1213 1415 1617 1819 2021 2223 2425 2627 2829 3031 32P1HDR_2X16UART_RTS MRB-UAR T_RTS/ KBI 1P7KMD1I2C_SDA MRB-I 2C _SDAKBI1P6MRB-PTD7/32M_OUTKMD31 23 4657 891011 1213 1415 1617 1819 2021 2223 2425 2627 2829 3031 32P2HDR_2X16MRB-UART_CTS/TPM2UART_CTSKMD2KMD0KBI1P3LED4KMD4KBI1P4KBI1P2KBI1P1KBI1P0KBI1P5KMD5SPI_MOSILED2I2C_SCL MRB-I2C_SCL
1323x Remote Control Motherboard1323x Development Hardware Reference Manual, Rev. 1.0 Freescale Semiconductor 4-9P2-5, P2-6 PTB2//KBI1P2 Port B Bit 2 / KBI1 Input Bit 2 RCM switch matrix; jumper requiredP2-7, P2-8 PTB3//KBI1P3 Port B Bit 3 / KBI1 Input Bit 3 RCM switch matrix; jumper requiredP2-9, P2-10 PTB4//KBI1P4 Port B Bit 4 / KBI1 Input Bit 4 RCM switch matrix; jumper requiredP2-11, P2-12 PTB5//KBI1P5 Port B Bit 5 / KBI1 Input Bit 5 RCM switch matrix; jumper requiredP2-21, P2-22 PTB6//KBI1P6 Port B Bit 6 / KBI1 Input Bit 6 RCM switch matrix; jumper requiredP1-17, P1-18 PTB7//KBI1P7 Port B Bit 7 / KBI1 Input Bit 7 • UART flow control RTS input to MCU; jumper required • Connects to RCM USB <> UART deviceP2-15, P2-16 PTC0/KBI2P0 Port C Bit 0 / KBI2 Input Bit 0 RCM switch matrix; jumper requiredP2-23, P2-24 PTC1/KBI2P1 Port C Bit 1 / KBI2 Input Bit 1 RCM switch matrix; jumper requiredP2-19, P2-20 PTC2/KBI2P2 Port C Bit 2 / KBI2 Input Bit 2 RCM switch matrix; jumper requiredP2-25, P2-26 PTC3/KBI2P3 Port C Bit 3 / KBI2 Input Bit 3 RCM switch matrix; jumper requiredP1-9, P1-10 PTC4/SPICLK Port C Bit 4 / SPI clock • Used; jumper required • Connected to serial FLASH on MRB • Connected to serial LCD interfaceP1-2 PTC5/SS Port C Bit 5 / SPI slave select • Unused on RCM • Must be in-active for LCD access • Connected to serial FLASH on MRBP1-6 PTC6/MISO Port C Bit 6 / SPI MISO • Unused on RCM • Connected to serial FLASH on MRBP1-3, P1-4 PTC7/MOSI Port C Bit 7 / SPI MOSI • Used; jumper required • Connected to serial FLASH on MRB • Connected to serial LCD interfaceP1- 15, P1-16 PTD0/TPM0 Port D Bit 0 / TPM0 signal Drives LED3; jumper requiredP2-27, P2-28 PTD1/TPM1 Port D Bit 1/ TPM1 signal Drives LED4; jumper requiredP1-21, P1-22 PTD2/TPM2 Port D Bit 2 / TPM2 signal • UART flow control CTS output from MCU; jumper required • Connects to RCM USB <> UART deviceP2-29, P2-30 PTD3/TPM3 Port D Bit 3 / TPM3 signal RCM switch matrix; jumper requiredP2-32 PTD4/CMT Port D Bit 4/ CMT output • Not used on RCM • Connected to IR blaster on MRBP1-7, P1-8 PTD6/RXD Port D Bit 6 / UART RXD input • UART RXD input to MCU; jumper required • Connects to RCM USB <> UART deviceP1-11, P1-12 PTD5/TXD Port D Bit 5 / UART TXD output • UART TXD output from MCU; jumper required • Connects to RCM USB <> UART deviceP1-31, P1-32 PTD7/32MOUT Port D Bit 7 • RCM switch matrix; jumper requiredTable 4-3. 1323x-RCM P1 and P2 Pin Header Function Description (continued)1323x-REMHeader PinsMC13233Signal Name Description 1323x-REM Application / Notes
1323x Remote Control Motherboard1323x Development Hardware Reference Manual, Rev. 1.0 4-10 Freescale Semiconductor4.2.3 1323x-RCM Onboard Peripheral FunctionsThe 1323x-RCM has a rich set of peripheral functions useful to evaluate the MC13233 and to implement a full featured remote control.4.2.3.1 USB InterfaceFor many applications or demonstrations it is desirable to connect the 1323x-RCM to a PC or other device. A USB port is provided with a USB “B” receptacle plug. The port is connected to a FTDI FT232RQ USB <> UART device that appears as a Virtual COM port (VCP) to the PC. PC drivers are available with the module.The USB interface is configured as a "Bus Powered" device and can draw all required power from the USB interface. The device is USB 2.0 full speed compatible. The USB connector is designated as J15. Figure 4-5 shows the connector pinout.Figure 4-5. USB Connector Pinout4.2.3.2 128x32 Graphic/Alphanumeric LCDThe 1323x-RCM supports a 128x32 pixel STN passive trans-reflective monochrome graphic LCD that provides for alphanumeric or graphic readout. The LCD module is mounted on top of the main circuit board and connects via a 16-pin connector. Figure 4-6 shows the LCD interface schematic.• The display is an CRYSTALFONZ #CFAG12832A-YGH-N• Viewing area is 51.0 (W) × 17.8 (H) mm• The LCD operates from 5 Vdc generated from the main operating voltage through a boost switching regulator. The LCD module requires a highly regulated 5 V so that the high voltages generated onboard the display are consistent.• The LCD has optional yellow-green LED backlighting— Typical current of 30 mA when full on— Enabled via Jumper J10— Always on when enabled.• LCD interface to the MCU is via the SPI port - although the LCD module only supports a parallel interface (8-bit or 4-bit modes), the 1323x-RCM uses a serial interface derived from the SPI port— The SPI serial stream is loaded into an 8-bit shift register (74AHCT164) used as a serial-to-parallel converter 1234S1S21234+D-DGVJ15USB_TY PE_BDATA_PDATA_MV_BUS
1323x Remote Control Motherboard1323x Development Hardware Reference Manual, Rev. 1.0 Freescale Semiconductor 4-11— Nibble (4-bit) parallel mode is used on the LCD and the shift register provides the 4 data bits and the RS control signal— The 4-data and RS control are strobed into the LCD via the LCD_CTL0 control signal derived from MC13233 PTA2 output.— LCD write mode only is supported; the LCD cannot be read.— The SPI port is shared with the serial FLASH on the 1323x-MRB. SS must be inactive (high) when writing to the LCD• The onboard controller is a member of the Sitronix ST7920 Series family with an integrated display data RAM and alphanumeric character setFigure 4-6. 1323x-RCM LCD Interface Circuit4.2.3.3 36 Pushbutton 6x6 Switch MatrixThe1323x-RCM provides an 36 pushbutton 6x6 switch matrix for user application input interface.• The matrix utilizes MC13233 KBI inputs• All switches have interrupt and device wake up capability• For these 36 switches— Includes the pushbutton array— Includes two switches located to the right and two switches to the left of the LCD— Includes switches SW31 and SW32 located on the bottom (non-component) side of the board— Does not support the two switches (KB0 and KB1) located near the touchpad.4.2.3.4 Synaptics TouchpadA Synaptics® Touchpad™ capacitive touch sensor is mounted on the 1323x-RCM for pointing functionality.• The touchpad is approximately 30mm tall x 45mm wide• Interface to the MCU uses the IIC interface• The touchpad has a separate interrupt request line that is tied to the KBI1P6 MCU input• The MCU reset is tied to the touchpad and resets the touchpad whenever a system reset occurs• The touchpad support two independent KBI signals that are connected to pushbuttons KB0 and KB1and used for touchpad select functions• The touchpad is soldered to the 1323x-RCM using two SMT headers C310. 1 UFR3 210KR3143R301K1 32R5 3 5KV_LC DQ0Q1Q2Q3Q4VSS1VDD2Vo3RS4R/W5E6DB07DB18DB29DB310DB411DB512DB613DB714ANODE15KATODE16DS1LC D + HD R 1X16 + CON 1 X16LC D_ CT L012J10HDR 1X28-B IT SH IFT REGI STER3 5421U7SN 74 A HC T1G08Q0 3Q1 4Q2 5Q3 6Q4 10Q5 11Q6 12Q7 13VCC 14GND7DSA1DSB2CP8MR 9U674AHCT164V_LC DV_LCDR51 3.3KDN PSPI_MOSISPI_CLKVCCV_LC DC-A1C+B1V_INB3ENA3GNDA2V_OUT C1C2+ C2C2 - C3U10F AN 5665C382. 2 uFC442 . 2uFR5 00TP3 3C452.2uFC462. 2 uF5 V BO OST CHARG E PU MPLCDVCCV_5VQ0Q1Q2Q3Q4CON TRAST ADJ USTV_LC DV_LCD
1323x Remote Control Motherboard1323x Development Hardware Reference Manual, Rev. 1.0 4-12 Freescale SemiconductorFigure 4-7 shows the touchpad circuit.Figure 4-7. 1323x-RCM Touchpad Circuit4.2.3.5 3-Axis AccelerometerThe 1323x-RCM contains a Freescale MMA7660 3-axis accelerometer with IIC interface.• Uses a 3mm x 3mm x 0.9mm DFN package• Device interface supports IIC bus and system reset• Supports an auto-wake/sleep feature for Low power consumption.• When the device is in auto-sleep state, if a shake interrupt, tap interrupt, Delta G, or orientation detection interrupt occurs, the device comes out of sleep mode and generates an interrupt request via the IRQ signalFigure 4-8 shows the accelerometer circuit.Figure 4-8. 1323x-RCM Accelerometer Circuit4.2.3.6 BuzzerThe 1323x-RCM provides a single tone audio buzzer.• Device LS1, CUI Inc., Part No. CMI-1240• 4.0 kHz resonant frequency• Device is buffered by Q2 and active when MCU output PTA1 is high (see Table 4-3)Figure 4-9 shows the buzzer circuit. R5210KVDD1SDA2SCL3GND4IRQ5RESET6KBI 07KBI 18NC1 9NC2 10NC3 11NC4 12NC5 13NC6 14J11TOUCHPADI2C_SDAV_TPDR3410KI2C_SCLR3310KKBI1P6TPKBI 1TPKBI 0RSTbV_TPD1423KB0PB switchTPKBI0 TPKBI11423KB1PB switchTPKBI 1TPKBI0 RESERVED1NC12AVDD3AVSS4INT5NC2 10DVDD 9DVSS 8SDA 7SC L 6U5MMA7660FCC2810UFC2610UFC290.1U FC270.1UFI2C_SDAI2C_SCLIRQbV_ACCV_ACC
1323x Remote Control Motherboard1323x Development Hardware Reference Manual, Rev. 1.0 Freescale Semiconductor 4-13Figure 4-9. 1323x-RCM Buzzer Circuit4.2.3.7 Blue Indicator LEDThe1323x-RCM provides 4 blue LEDs for user application indicator outputs. Refer to Table 4-3 for listings of the MC13233 outputs that drive the LEDs.
1323x Development Hardware Reference Manual, Rev. 1.0 4-14 Freescale Semiconductor 1323x Remote Control Motherboard4.3 Schematic, Board Layout, and Bill of MaterialFigure 4-10. 1323x-RCM Schematic (1 of 3)5544332211D DC CB BA AV_MRBV_MRBV_LED V_LED V_LED V_LEDV_USBV_ACCV_ACCV_BUZMRB-I2C_SDAKBI1P0 KBI1P1 KBI1P2 KBI1P3 KBI1P4 KBI1P5LED2 LED3 LED4LED1MRB-RSTbMRB-SPI_CLKMRB-SPI_MISOMRB-SPI_MOSIMRB-SPI_SSMRB-UART_RTS/KBI1P7MRB-UART_CTS/TPM2MRB-KBI1P0MRB-KBI1P2MRB-KBI1P1MRB-KBI1P3MRB-I2C_SCLMRB-UART_TXDMRB-UART_RXDBUZZERI2C_SCLI2C_SDAIRQbMRB-TPM0MRB-PTD7/32M_OUTMRB-KBI1P5MRB-KBI2P0MRB-KBI2P2MRB-PTA4/32K_OUTMRB-PTA2/LCD_CTL0MRB-KBI1P4MRB-KBI1P6MRB-KBI2P1MRB-KBI2P3MRB-PTA3/IRQbMRB-PTD1/TPM1 MRB-PTD3/TPM3MRB-PTD4/CMTMRB-KBI1P3MRB-KBI1P1MRB-KBI1P2MRB-KBI1P4MRB-PTD4/CMTMRB-SPI_MOSIMRB-SPI_SSMRB-KBI1P5MRB-KBI1P0MRB-KBI2P0MRB-KBI2P2MRB-PTD1/TPM1MRB-PTD3/TPM3SPI_MOSIKMD0KMD2LED4KBI1P3KBI1P1KBI1P2KBI1P4KMD4KBI1P5KBI1P0DATA_PDATA_MUART_TXDUART_RTSUART_RXDUART_CTSMRB-KBI2P3MRB-KBI2P1MRB-KBI1P6MRB-PTA4/32K_OUTMRB-PTA3/IRQbMRB-PTD7/32M_OUTKMD5MRB-PTA2/LCD_CTL0LCD_CTL0IRQbKMD1KBI1P6KMD3LED2MRB-PTA1MRB-PTA0MRB-SPI_MISOMRB-UART_TXDUART_TXDMRB-SPI_CLKSPI_CLKMRB-UART_RXDUART_RXDMRB-RSTbRSTbMRB-TPM0LED3MRB-UART_RTS/KBI1P7UART_RTSMRB-I2C_SDAI2C_SDAMRB-UART_CTS/TPM2UART_CTSMRB-I2C_SCLI2C_SCLMRB-PTA0LED1MRB-PTA1BUZZERKMD0KMD1KMD2KMD3KMD4KMD5Drawing Title:Size Document Number RevDate: Sheet ofPage Title:ICAP Classification: FCP: FIUO: PUBI:SCH-26116 PDF: SPF-26116 B11323X REMOTE CONTROL MOTHERBOARDCFriday, February 05, 2010INTERFACE35X______Drawing Title:Size Document Number RevDate: Sheet ofPage Title:ICAP Classification: FCP: FIUO: PUBI:SCH-26116 PDF: SPF-26116 B11323X REMOTE CONTROL MOTHERBOARDCFriday, February 05, 2010INTERFACE35X______Drawing Title:Size Document Number RevDate: Sheet ofPage Title:ICAP Classification: FCP: FIUO: PUBI:SCH-26116 PDF: SPF-26116 B11323X REMOTE CONTROL MOTHERBOARDCFriday, February 05, 2010INTERFACE35X______20-PIN GPIOSTANDARD HEADERP1 & P2:IO PIN MAPPINGMUST USE SHUNTS TO ENABLEBOARD FUNCTIONALLITY.GPIOSOCKETS FOR 1323X-MRB ASSEMBLYDIGITAL ACCELEROMETERKEYBOARD MATRIXUSB/UART TRANSCEIVERLED'S & BUZZERGUIDE MP3 STOCK MENUPOWERSK1 SK2 SK3 SK4VOL+ VOL- CH+MUTE CH-STOP PAUSE REC RW PLAY FFTVENTERCLEAR9087123456R28 4.7KR28 4.7KTP15TP15C2415PFC2415PFSW18PB switchSW18PB switch1 42 3SW8PB switchSW8PB switch1 42 3SW32PB switchDNPSW32PB switchDNP1 42 3SW26PB switchSW26PB switch1 42 3LED4BLUELED4BLUE21LED1BLUELED1BLUE21LED3BLUELED3BLUE21LED2BLUELED2BLUE21C300.1UFC300.1UFTP14TP14TP32TP32TP31TP31SW17PB switchSW17PB switch1 42 3SW9PB switchSW9PB switch1 42 3SK2PB switchSK2PB switch1 42 3SW27PB switchSW27PB switch1 42 3U5MMA7660FCU5MMA7660FCRESERVED1NC12AVDD3AVSS4INT5NC2 10DVDD 9DVSS 8SDA 7SCL 6SW10PB switchSW10PB switch1 42 3SW25PB switchSW25PB switch1 42 3SK4PB switchSK4PB switch1 42 3SW1PB switchSW1PB switch1 42 3R20 1KR20 1KSW12PB switchSW12PB switch1 42 3+LS1BUZZER+LS1BUZZER12SW3PB switchSW3PB switch1 42 3C2810UFC2810UFSW5PB switchSW5PB switch1 42 3R23390R23390C250.1UFC250.1UFJ9CON_2X9J9CON_2X91 23 4657 891011 1213 1415 1617 18Q2MMBT3904LT1GQ2MMBT3904LT1G2 31R22 1KR22 1KSW28PB switchSW28PB switch1 42 3SW24PB switchSW24PB switch1 42 3R24390R24390R25390R25390C2610UFC2610UFR26390R26390R21 1KR21 1KSW19PB switchSW19PB switch1 42 3SW29PB switchSW29PB switch1 42 3C290.1UFC290.1UFP1HDR_2X16P1HDR_2X161 23 4657 891011 1213 1415 1617 1819 2021 2223 2425 2627 2829 3031 32C2315PFC2315PFSW30PB switchDNPSW30PB switchDNP1 42 3SW20PB switchSW20PB switch1 42 3C270.1UFC270.1UFJ8CON_2X10J8CON_2X101 23 4657 891011 1213 1415 1617 1819 20R48 0R48 0R19 1KR19 1KTP13TP13R270R270TP30TP30SW13PB switchSW13PB switch1 42 3R49 0R49 0SW21PB switchSW21PB switch1 42 3TP17TP17R2947KR2947KSW22PB switchSW22PB switch1 42 3SW14PB switchSW14PB switch1 42 3SW11PB switchSW11PB switch1 42 3SK1PB switchSK1PB switch1 42 3SW2PB switchSW2PB switch1 42 3P2HDR_2X16P2HDR_2X161 23 4657 891011 1213 1415 1617 1819 2021 2223 2425 2627 2829 3031 32SW4PB switchSW4PB switch1 42 3SW6PB switchSW6PB switch1 42 3SW23PB switchSW23PB switch1 42 3SW15PB switchSW15PB switch1 42 3SW31PB switchDNPSW31PB switchDNP1 42 3TP16TP16U4 FT232RQU4 FT232RQGND14AGND24RI# 3DCD# 7DSR# 6DTR# 313V3OUT16VCCIO1OSCI27RESET#18NC623OSCO28CBUS4 9CBUS3 11CBUS1 21CBUS0 22CBUS2 10NC529 NC425 NC313 NC212 NC15USBDP14USBDM15VCC19GND420 GND217TEST26CTS# 8RTS# 32RXD 2TXD 30EP33SW16PB switchSW16PB switch1 42 3SW7PB switchSW7PB switch1 42 3SK3PB switchSK3PB switch1 42 3
1323x Remote Control Motherboard1323x Development Hardware Reference Manual, Rev. 1.0 Freescale Semiconductor 4-15 Figure 4-11. 1323x-RCM Schematic (2 of 3)5544332211D DC CB BA AV_LCDV_LCDV_LCDV_LCDV_TPD V_TPDV_LCD VCCTPKBI0 TPKBI1Q0Q1Q2Q3Q4SPI_MOSISPI_CLKQ0Q1Q2Q3Q4LCD_CTL0I2C_SDAI2C_SCLKBI1P6RSTbTPKBI0TPKBI1Drawing Title:Size Document Number RevDate: Sheet ofPage Title:ICAP Classification: FCP: FIUO: PUBI:SCH-26116 PDF: SPF-26116 B11323X REMOTE CONTROL MOTHERBOARDCFriday, February 05, 2010LCD & TOUCHPAD45X______Drawing Title:Size Document Number RevDate: Sheet ofPage Title:ICAP Classification: FCP: FIUO: PUBI:SCH-26116 PDF: SPF-26116 B11323X REMOTE CONTROL MOTHERBOARDCFriday, February 05, 2010LCD & TOUCHPAD45X______Drawing Title:Size Document Number RevDate: Sheet ofPage Title:ICAP Classification: FCP: FIUO: PUBI:SCH-26116 PDF: SPF-26116 B11323X REMOTE CONTROL MOTHERBOARDCFriday, February 05, 2010LCD & TOUCHPAD45X______TPKBI1TPKBI0LCDTOUCHPAD8-BIT SHIFT REGISTERCONTRAST ADJUSTU674AHCT164U674AHCT164Q0 3Q1 4Q2 5Q3 6Q4 10Q5 11Q6 12Q7 13VCC 14GND7DSA1DSB2CP8MR 9R3410KR3410KR53 5KR53 5K1 32KB1PB switchKB1PB switch1423U7SN74AHCT1G08U7SN74AHCT1G083 5421R3310KR3310KC310.1UFC310.1UFR3210KR3210KR301KR301KR3143R3143J11TOUCHPADJ11TOUCHPADVDD1SDA2SCL3GND4IRQ5RESET6KBI07KBI18NC1 9NC2 10NC3 11NC4 12NC5 13NC6 14R51 3.3KDNPR51 3.3KDNPR5210KR5210KJ10HDR 1X2J10HDR 1X212DS1LCD + HDR 1X16 + CON 1X16DS1LCD + HDR 1X16 + CON 1X16VSS1VDD2Vo3RS4R/W5E6DB07DB18DB29DB310DB411DB512DB613DB714ANODE15KATODE16KB0PB switchKB0PB switch1423
1323x Remote Control Motherboard1323x Development Hardware Reference Manual, Rev. 1.0 Freescale Semiconductor 4-16 Figure 4-12. 1323x-RCM Schematic (3 of 3)5544332211D DC CB BA AV_5VV_3V3V_LEDV_LEDV_TPDV_ACCVCCV_USBV_BUS V_SERV_BATV_MRBV_LCDV_MAINVCCV_JACKV_DCV_USBV_BHLV_SERV_BUSV_BATV_BUZV_DCV_JACKV_SERV_BUSDATA_MDATA_PDrawing Title:Size Document Number RevDate: Sheet ofPage Title:ICAP Classification: FCP: FIUO: PUBI:SCH-26116 PDF: SPF-26116 B11323X REMOTE CONTROL MOTHERBOARDCFriday, February 05, 2010POWER MANAGEMENT55X ______Drawing Title:Size Document Number RevDate: Sheet ofPage Title:ICAP Classification: FCP: FIUO: PUBI:SCH-26116 PDF: SPF-26116 B11323X REMOTE CONTROL MOTHERBOARDCFriday, February 05, 2010POWER MANAGEMENT55X ______Drawing Title:Size Document Number RevDate: Sheet ofPage Title:ICAP Classification: FCP: FIUO: PUBI:SCH-26116 PDF: SPF-26116 B11323X REMOTE CONTROL MOTHERBOARDCFriday, February 05, 2010POWER MANAGEMENT55X ______LEDTOUCHPADACCELEROMETERPOWER ON3.3V BUCK/BOOST REGULATORTO USE TPS63000,REPLACE RESISTORS WITHTHE FOLLOWING VALUES:R45 = 100 OHM, R47 = 1.24MAND POPULATE R46.OUTPUT VOLTAGE WILL BE 3.6VMODULAR REFERENCE BOARD5V BOOST CHARGE PUMPLCD3.3V POWER NETWORK5V POWER NETWORKEXTERNAL SUPPLY.NEVER SHUNT!!!BUZZERF10.5AF10.5A1 2TP22TP22BH2125BH2125R39330R39330L3 3.3uHL3 3.3uH1 2TL4TL4C330.1UFC330.1UFBT1BATTERY HOLDERBT1BATTERY HOLDER12D8MBR0520LT1GD8MBR0520LT1GR370R370C3210UFC3210UFR46200KDNPR46200KDNPFID1FIDFID1FIDR350R350BH6125BH6125TL1TL1D11MBR0520LT1GD11MBR0520LT1GC4210UFC4210UFD9MBR0520LT1GD9MBR0520LT1GTL5TL5U9FAN5665U9FAN5665C-A1C+B1V_INB3ENA3GNDA2V_OUT C1C2+ C2C2- C3LED5REDLED5RED21BH3125BH3125R420R420TP24TP24D12MBR0520LT1GD12MBR0520LT1GC342.2uFC342.2uFR4110KR4110KC390.1UFC390.1UFSL14P2T SWITCHSL14P2T SWITCH123456 789101112C372.2uFC372.2uF1234+D-DGVJ15USB_TYPE_B1234+D-DGVJ15USB_TYPE_B1234S1S2C4310UFC4310UFTP26TP26R384.7KR384.7KR450R450FID2FIDFID2FIDL460OHML460OHM1 2TL2TL2TP28TP28U8TPS63001U8TPS63001EN6GND9L14L2 2PS/SYNC7VOUT 1VIN5VINA8FB 10PGND 3PPAD 11TP25TP25BH4125BH4125R430R430R400R400TP29TP29D10MBR0520LT1GD10MBR0520LT1GR470R470TP27TP27TP19TP19R360R360BH7125BH7125TP23TP23D13MBR0520LT1GD13MBR0520LT1GBH1125BH1125TP21TP21TP20TP20C404.7uFC404.7uFFID3FIDFID3FIDTL3TL3R440R440C410.01UFC410.01UFC352.2uFC352.2uFBH5125BH5125J14HDR 1X2J14HDR 1X212C362.2uFC362.2uFTL6TL6Q3SI2305Q3SI2305132
1323x Remote Control Motherboard1323x Development Hardware Reference Manual, Rev. 1.0 Freescale Semiconductor 4-17Figure 4-13. 1323x-RCM PCB Component Location (Top View)
1323x Remote Control Motherboard1323x Development Hardware Reference Manual, Rev. 1.0 4-18 Freescale SemiconductorFigure 4-14. 1323x-RCM PCB Test Points
1323x Remote Control Motherboard1323x Development Hardware Reference Manual, Rev. 1.0 Freescale Semiconductor 4-19Figure 4-15. 1323x-RCM PCB Layout (Top View)
1323x Remote Control Motherboard1323x Development Hardware Reference Manual, Rev. 1.0 4-20 Freescale SemiconductorFigure 4-16. 1323x-RCM PCB Layout (Bottom View)
1323x Remote Control Motherboard1323x Development Hardware Reference Manual, Rev. 1.0 Freescale Semiconductor 4-214.3.1 1323x-RCM Bill of MaterialsTable 4-4. Bill of MaterialsItem Qty. Reference Value Description Mfg. Name Mfg. Part Number1 8 BH1,BH2,BH3,BH4,BH5,BH6,BH7,BH8125 NON-PLATED MOUNTING HOLE 125 DRILL / 160 KEEPOUT NO PART TO ORDER21BT1 BATTERY HOLDERBATTERY HOLDER 2XAA TH Keystone Electronics24623 2 C23,C24 15PF CAP CER 15PF 50V 5% C0G 0402Kemet C0402C150J5GAC4 4 C25,C30,C33,C39 0.1UF CAP CER 0.1UF 16V 10% X7R 0402Murata GRM155R71C104KA88D5 5 C26,C28,C32,C42,C4310UF CAP CER 10UF 10V 10% X7R 0805Murata GRM21BR71A106KE51L6 3 C27,C29,C31 0.1UF CAP CER 0.1UF 50V 10% X7R 0603Murata GRM188R71H104KA93D7 4 C34,C35,C36,C37 2.2uF CAP CER 2.2UF 6.3V 10% X5R 0603Murata GRM188R60J225KE19D8 1 C40 4.7uF CAP CER 4.7UF 10V 10% X5R 0603Taiyo Yuden LMK107BJ475KA-T9 1 C41 0.01UF CAP CER 0.01UF 10V 20% X7R 0402Avx 0402ZC103MAT2A10 1 DS1 LCD + HDR 1X16 + CON 1X16SUBASSY LCD 128X32 DOT 4.5-5V TH + HDR 1X16 TH 100MIL SP 330H AU + CON 1X16 SKT TH 100MIL SP 335 AUFreescale Semiconductor370-76474, 210-75955, 210-7781211 6 D8,D9,D10,D11,D12,D13MBR0520LT1GDIODE SCH 0.5A 20V SOD-123On SemiconductorMBR0520LT1G12 3 FID1,FID2,FID3 FID FIDUCIAL 060 MIL PAD W/120 SOLDERMASK AND 040 MIL PAD W/90 MIL SOLDERMASK NO PART TO ORDERGeneric FID-04013 1 F1 0.5A FUSE FAST 0.5A 63V SMT 1206Littelfuse 0437.500WR14 1 J8 CON_2X10 CON 2X10 SKT TH 100MIL CTR 335H AU 104LSamtec SSW-110-01-G-D15 1 J9 CON_2X9 CON 2X9 SKT TH 100MIL SP 335H AU 194LSamtec SSW-109-02-G-D16 2 J10,J14 HDR_1X2 HDR 1X2 TH 100MIL SP 375H AUTyco Electronics826629-217 1 J11 TOUCHPAD TOUCHPAD SERIAL 3V TH Synaptics, Inc 515-000188-0110
1323x Remote Control Motherboard1323x Development Hardware Reference Manual, Rev. 1.0 4-22 Freescale Semiconductor18 1 J15 USB_TYPE_BCON 2X2 USB_TYPE_B SKT RA SHLD TH 2.5MM SP 453H AUTyco Electronics292304-219 35 SW1,SK1,KB1,SW2,SK2,SW3,SK3,SW4,SK4,SW5,SW6,SW7,SW8,SW9,SW10,SW11,SW12,SW13,SW14,SW15,SW16,SW17,SW18,SW19,SW20,SW21,SW22,SW23,SW24,SW25,SW26,SW27,SW28,SW29,KB0PB switch SW SMT 4.0MM FMS 0.1A MAX 16V MAX ROHS COMPLIANTBourns 7914J-1-000E20 4 LED1,LED2,LED3,LED4BLUE LED BLUE SGL 20MA SMT 0805Lite On LTST-C171TBKT-5A21 1 LED5 RED LED RED CLEAR SGL 30MA SMT 0805Lite On LTST-C171KRKT22 1 LS1 BUZZER BUZZER PIEZO AUDIO 83DB 4KHZ 8MA 12V SMTCui Stack CMI-124023 1 L3 3.3uH IND PWR 3.3UH@100KHZ 3.3A 20% SMTVishay IntertechnologyIHLP2020BZER3R3M0124 1 L4 60OHM IND FER BEAD 60OHM@100MHZ 500MA -- 0603Murata BLM18PG600SN1_25 2 P1,P2 HDR_2X16 HDR 2X16 TH 100MIL CTR 330H AU 100LSamtec TSW-116-07-S-D26 1 Q2 MMBT3904LT1GTRAN NPN GEN 200MA 40V SOT-23On SemiconductorMMBT3904LT1G27 1 Q3 SI2305 TRAN PMOS PWR 4.1A 8V SOT23Vishay IntertechnologySI2305ADS-T1-GE328 5 R19,R20,R21,R22,R301K RES MF 1.0K 1/16W 5% 0402 Vishay IntertechnologyCRCW04021K00JNED29 4 R23,R24,R25,R26 390 RES MF 390 OHM 1/16W 5% 0402Bourns CR0402-JW-391GLF30 2 R27,R45 100 RES MF 100 OHM 1/16W 5% 0402Vishay IntertechnologyCRCW0402100RJNED31 10 R28,R35,R36,R37,R40,R42,R43,R44,R48,R490 RES TF ZERO OHM 1/16W RC0402Vishay IntertechnologyCRCW04020000ZS32 6 R29,R32,R33,R34,R41,R5210K RES MF 10K 1/16W 5% 0402 Vishay IntertechnologyCRCW040210K0JNEDTable 4-4. Bill of MaterialsItem Qty. Reference Value Description Mfg. Name Mfg. Part Number
1323x Remote Control Motherboard1323x Development Hardware Reference Manual, Rev. 1.0 Freescale Semiconductor 4-2333 1 R31 39 RES MF 39 OHM 1/16W 5% 0402Smec RC73L2Z390JTF34 1 R38 4.7K RES MF 4.7K 1/16W 5% 0402 Smec RC73L2Z472JTF35 1 R39 330 RES MF 330 OHM 1/16W 5% 0402Vishay IntertechnologyCRCW0402330RJNED36 1 R46 200K RES MF 200K 1/16W 5% 0402 Yageo America RC0402JR-07200KL37 1 R47 1.24M RES MF 1.24M 1/16W 1% 0402Vishay IntertechnologyCRCW04021M24FKED38 1 R50 5K RES POT 5.0K 1/4W 20% SMT Bourns 3314J-1-502E39 1 R51 3.3K RES MF 3.3K 1/16W 5% 0402 Vishay IntertechnologyCRCW04023K30JNED40 1 SL1 4PDT SWITCHSW 4PDT SLD TH RA 30V 100MA --Tyco Electronics1-1437575-141 3 SW30,SW31,SW32PB switch SW SMT 4.0MM FMS 0.1A MAX 16V MAX ROHS COMPLIANTBourns 7914J-1-000E42 19 TP13,TP14,TP15,TP16,TP17,TP19,TP20,TP21,TP22,TP23,TP24,TP25,TP26,TP27,TP28,TP29,TP30,TP31,TP32TPAD_040 TEST POINT PAD 40MIL DIA SMT, NO PART TO ORDERNotacomponent NOTACOMPONENT43 1 U4 FT232RQ IC XCVR USB TO UART CTLR 3.3-5.25V QFN32Future Technology Devices International Ltd.FT232RQ44 1 U5 MMA7660FCIC SENSOR ACCELEROMETER 2.4-3.6V DFN10Freescale SemiconductorMMA7660FC45 1 U6 74AHCT164 IC REG SHIFT SER/PAR 8BIT 4.5-5.5V TSSOP14Nxp Semiconductors74AHCT164PW,11246 1 U7 SN74AHCT1G08IC GATE AND SGL 2-INPUT POSITIVE 4.5-5.5V SOT23-5Texas Instru-mentsSN74AHCT1G08DBVR47 1 U8 TPS63001 IC LIN DCDC SYNC 3.3V OUTPUT 1250-1800KHZ 1.8-5.5V QFN-10Texas Instru-mentsTPS63001DRCTTable 4-4. Bill of MaterialsItem Qty. Reference Value Description Mfg. Name Mfg. Part Number
1323x Remote Control Motherboard1323x Development Hardware Reference Manual, Rev. 1.0 4-24 Freescale Semiconductor48 1 U9 FAN5665 IC LIN DCDC SWT 5V 2.9-5.5V WLCSP-8Fairchild FAN5665UCXTable 4-4. Bill of MaterialsItem Qty. Reference Value Description Mfg. Name Mfg. Part Number
1323x Development Hardware Reference Manual, Rev. 1.0 Freescale Semiconductor 5-1Chapter 5 1323x Remote Extender Motherboard5.1 1323x-REM OverviewThe 1323x-Remote Extender Motherboard (1323x-REM) is a motherboard that accepts the 1323x-Modular Reference Board (1323x-MRB) plug-in module (daughtercard) and supplies a power supply and set of interface peripherals. The two boards in combination provide a simple platform to evaluate the MC1323x, develop software, and demonstrate IEEE 802.15.4 based networking capabilities. 5.1.1 FeaturesThe 1323x-REM provides the following features:• Small form factor (3.1 x 3.1 inches)• 2-Layer metal, 0.034 inch thick FR4 board• Two connectors provide daughter card mounting— 20-Pin primary connector— 18-Pin secondary connector— Provide main supply voltage to board— Provide access to all MC13233 GPIO• Flexible power supply— Sources include USB port, two AA batteries, or DC source— Power-On LED—On-Off switch• USB <> UART serial port• 2x4 Switch matrix• IR receiver• Four application controlled blue indicator LEDs• Secondary set of pin headers uses jumpers to enable/disable IO connections and allows user application connection to MC13233 GPIO
1323x Remote Extender Motherboard1323x Development Hardware Reference Manual, Rev. 1.0 5-2 Freescale Semiconductor5.1.2 Form FactorFigure 5-1 shows a photo of the 1323x-REM showing the locations of connectors and headers.Figure 5-1. 1323x-REMThe1323x-MRB mounts on the 1323x-REM via receptacles J8 and J9. Figure 5-1 shows an outline of the 1323x-MRB placement when mounted.2x4 SwitchUSBPrimary 20-Pin IOConnector (J8)On / OffSecondary 18-Pin IOConnector (J9)IR ReceiverMatrixConnector J15SwitchSL11323x-MRB Outline(When mounted)4 Blue LEDsExternalSupplyJ14Power-OnLEDGPIO EnablePin HeaderP1GPIO EnablePin HeaderP23.1 Inches79 mm3.1 Inches79 mm
1323x Remote Extender Motherboard1323x Development Hardware Reference Manual, Rev. 1.0 Freescale Semiconductor 5-35.1.3 Board Level SpecificationsNOTETemperature range specifications apply to REM used in combination with MRB.Table 5-1. 1323x-REM SpecificationsParameter Units Notes/ConditionsMIN TYP MAXGeneralSize (PCB: X, Y) 79 x 793.1 x 3.1mminchesLayer build (PCB) 0.80.034mminches2-LayerDielectric material (PCB) FR4PowerVoltage supply (DC) 2.3 5 6 VVoltage supply (USB) 4.4 5 5.25 V USB 2.0/1.1 standard specificationVoltage supply (Batteries) 2.8 3.2 VCurrent consumption 100 mATemperatureOperating temperature; non-battery operation (see note)-20 +25 +70 °C Operating temperature is limited to +70 °C due to switches. Basic circuit is good for a maximum temperature of +85 °C.Operating temperature; battery operation (see note)0 +25 +50 °C Operating temperature is limited by battery temperature rangeStorage temperature -30 +25 +70 °CUSB interface USB 2.0 and 1.1 full-speed compatibleIR ReceiverCarrier frequency 38 kHzAngle of half transmission distance +/-50 degreesRegulatory ApprovalCE (ETSI) Product is approved accordingly to the EN 300 328 V1.7.1 (2006-10) standardCE (EMC) Product is approved accordingly to the EN 301 489-1 V1.6.1 (2005-09) and EN 301 489-17 V1.2.1 (2002-08) standardsSafety
1323x Remote Extender Motherboard1323x Development Hardware Reference Manual, Rev. 1.0 5-4 Freescale Semiconductor5.2 Functional DescriptionThe 1323x-REM is a simple host motherboard for the 1323x-MRB. The two-board combination provides a simple evaluation and development platform for the MC13233. Figure 5-2 shows a simple block diagram. The 2-layer board provides a flexible power supply, eight pushbutton matrix, four indicator LEDs, IR receiver, and a USB <> UART serial port.As the board name implies this platform is useful to develop the host side (such as a DTV or entertainment console) of an RF remote control application. The MC13233 provides the RF node and an IR receiver is available to support legacy IR protocol remotes. Connection to a host is available through the USB port or any of the other generic MC13233 communications ports.The 1323x-REM is also recommended for target development of applications where there is little periphery circuitry. There are switches and indicator LEDs onboard for user interface, and if necessary, custom circuitry can be connected via the two pin headers that allow access to the MC13233 GPIO.In the following sections, refer to:•Figure 5-1 for location of connectors and features•Figure 5-2 for the functional blocks•Figure 5-8 and Figure 5-9 for the board schematicUL Product is approved accordingly to the IEC 60950-1 and EN 60950-1, First Edition standardsEnvironmentRoHS Product complies with the EU Directive 2002/95/EC of 27 January 2003WEEE Product complies with the EU Directive 2002/95/EC of 27 January 2003Table 5-1. 1323x-REM Specifications (continued)Parameter Units Notes/Conditions
1323x Remote Extender Motherboard1323x Development Hardware Reference Manual, Rev. 1.0 Freescale Semiconductor 5-5Figure 5-2. 1323x-REM Block Diagram5.2.1 Power ManagementThe 1323x-REM can be powered from two AA batteries, the USB connector 5 V supply, or an external DC supply and is also intended to power the 1323x-MRB. Figure 5-3 shows the power management circuit.Figure 5-3. 1323x-REM Power Management CircuitA boost-buck voltage regulator U8 is used in this design to allow operation over a relatively wide, low voltage input range, i.e., the TPS63001 regulator has input voltage range from 1.8 V to 5.5V. This allows a broad range of power supply sources. The regulated output voltage of the TPS63001 is 3.3 V which delivers about 3.05 V to the board due to the drop across the isolation Schottky diodes.Attributes of the power management circuit include:• Switch SL1 provides an ON/OFF function for all input voltage sources• Red LED5 provides a POWER-ON indicator for all sources• The 1323x-REM can derive power from three different sources -1. USB port Type-B connector J15 - power can be supplied from an actual USB port connection or from an AC to DC converter that uses the USB connector to supply power.2. External DC source via header J14 - a standard 0.1 in. spacing 1x2 pin header allows for connection of an external DC supply.1323x-MRBGPIO HeaderReceptaclesIRReceiver(38 kHz)VCCUSB 2.04 BlueIndicatorLEDsUSBType-BConnOn/OffSwitchUSB <> UARTSerial IC 8 SwitchMatrixPowerManagement GPIOPin HeadersOnLEDExternal DC2 AABatteryIR D8MBR 0 52 0L T1 GD10MBR0520LT1GD11MBR 05 20 LT1 GD12MBR0520LT1GD13MBR0520LT1G21LED 5RE DPOWER ONR39330V_LEDV_ MRBV_ LE DV_DCV_I RXC3210UF EN6GN D9L14L2 2PS/SY N C7VOUT 1VIN5VINA8FB 10PGND 3PPAD 11U8T PS6 30 011 2L3 3.3uHV_BATR384. 7 K132Q4S I 23 05R4110KTP27V_USB VCCTP21TP 25 TP24C330.1UFR450C4310UFR430TP2 3C4210 U FR350R360R400INFRARRED RXLEDV_MA INR46200KDNPMODULAR REFERENCE BOARDR470V_ 3V6TP1 9 TP20D9MBR 0 52 0L T1 G
1323x Remote Extender Motherboard1323x Development Hardware Reference Manual, Rev. 1.0 5-6 Freescale Semiconductor3. Battery Operation - a battery holder that accommodates two AA batteries is mounted on the non-component (back) side of the board and provides for battery operation.– If either the USB or external DC source is present, the battery source is disabled by MOSFET transistor Q3– The sources are all isolated and protected by Schottky diodes– The minimum effective battery operating voltage is controlled by the use the FTDI FT232RQ USB <> UART device - leakage current back through the FT232RQ UART connections to the MC13233 on the MRB can cause the Q3 MOSFET to partially turnoff at battery voltage below approximately 2.7-2.8 Vdc.NOTETo avoid current leakage through the USB device and lower minimum battery operating voltage for battery-only operation, remove the following jumpers:• P1, Pins 7-8• P1, Pins 11-12• P1, Pins 17-18• P1, Pins 21-22NOTEWhen battery operation is used, the temperature range of the two board system should be limited to within the specified temperature range of the battery technology. Table 5-1 limits temperature range from 0 °C to +50 °C when battery operation is applied.Table 5-2 lists the voltage source attributes.Table 5-2. 1323x-REM Voltage SourcesSource Connector Input Voltage Range DescriptionUSB Port USB Type-B J15 4.4 V - 5.25 V • The input voltage range is set to the USB specification value • The voltage can be supplied by either a standard USB cable connection or an AC to DC power adaptor that uses the USB connector J15 • If a power adaptor is in use, the USB serial port cannot be usedExternal DC Supply 1x2 Pin Hdr J14 2.3 V - 6 V The input voltage range is determined by the U8 regulator and the diode isolation circuitTwo AA Batteries Battery Holder 2.0 V - 3.1 V11The minimum operating battery voltage is determined by use model, see Note, Section 5.2.1, “Power Management” • The input voltage range reflects the usable range of alkaline cells and the voltage drop incurred by the diode isolation circuit. • The battery source is disabled if another source is connected
1323x Remote Extender Motherboard1323x Development Hardware Reference Manual, Rev. 1.0 Freescale Semiconductor 5-7Again referring to Figure 5-3, a number of zero-ohm resistors are provided to isolate different circuits and to allow current measurement:• VCC (main 1323x-REM supply) - resistor R35 • V_LED (all LEDs supply) - resistor R36• V_IRX (IR receiver supply) - resistor R40• V_MRB (1323x-MRB supply) - resistor R43Figure 5-4. 1323x-MRB Mounted on 1323x-REM5.2.2 GPIO Connection to 1323x-MRBIO Connectors J8 and J9 (see Figure 5-1) are receptacles that accept the 1323x-MRB pin headers to mount the daughtercard. Figure 5-4 shows the 1323x-REM with the 1323x-MRB mounted. Receptacles J8 and J9 connect to the MC13233 GPIO.To provide better access and versatility to the GPIO, a secondary set of pin headers P1 and P2 is connected in series with the IO signals:• Jumpers must be installed on P1 and P2 to connect 1323x-REM peripherals and functions• The pin headers provide direct access for connecting custom circuitry to the GPIO• Power and ground to primary connectors J8 and J9 are not enabled though the pin headersFigure 5-5 shows IO Header P1 andP2 pin mapping.
1323x Remote Extender Motherboard1323x Development Hardware Reference Manual, Rev. 1.0 5-8 Freescale SemiconductorFigure 5-5. 1323x-REM IO Connector J8 and J9 Pin MappingTable 5-3 list the P1 and P2 pin header function as it relates to the MC13233.Table 5-3. 1323x-REM P1 and P2 Pin Header Function Description1323x-REMHeader PinsMC13233Signal Name Description CommentsP1-27, P1-28 PTA0/XTAL_32K Port A Bit 2 / 32.768 kHz oscillator output • Drives LED1; jumper required • 32.768 kHz oscillator can be enabled on MRBP1-26 PTA1/EXTAL_32K Port A Bit 3 / 32.768 kHz oscillator input • Unused • 32.768 kHz oscillator can be enabled on MRBP1-14 RESET Device asynchronous hardware reset. Active low. Onboard Pullup • Unused • Reset signal driven from MRBP1-30 PTA2 Port A Bit 2. Onboard pullup for TM • Unused • TM enable; leave unconnectedP2-14 PTA3/IRQ Port A Bit 3 / IRQ. • Unused • Provides interrupt request input IRQ (active low)P2-17, P2-18 PTA4/XTAL_32KOUTPort A Bit 4 / Buffered 32.768 kHz clock output • Drives LED2; jumper required • Optional 32.768 kHz output clock for measuring reference oscillator accuracy (ppm)P1-20 PTA5/SDA Port A Bit 5 / IIC Bus data • Unused • Defaults to open drain for IIC • Pullup on MRBP1-24 PTA6/SCL Port A Bit 6 / IIC Bus clock • Unused • Defaults to open drain for IIC • Pullup on MRBP2-1, P2-2 PTB0/KBI1P0 Port B Bit 0 / KBI1 Input Bit 0 REM switch matrix; jumper requiredP2-3, P2-4 PTB1/KBI1P1 Port B Bit 1 / KBI1 Input Bit 1 REM switch matrix; jumper requiredP2-5, P2-6 PTB2//KBI1P2 Port B Bit 2 / KBI1 Input Bit 2 REM switch matrix; jumper requiredP2-7, P2-8 PTB3//KBI1P3 Port B Bit 3 / KBI1 Input Bit 3 REM switch matrix; jumper requiredP2-10 PTB4//KBI1P4 Port B Bit 4 / KBI1 Input Bit 4 Unused
1323x Remote Extender Motherboard1323x Development Hardware Reference Manual, Rev. 1.0 Freescale Semiconductor 5-95.2.3 1323x-REM Onboard Peripheral FunctionsThe 1323x-REM has a simple set of peripheral functions useful to evaluate the MC13233 and to implement simple node applications, especially a remote control receiver; i.e., interface to host platform.P2-12 PTB5//KBI1P5 Port B Bit 5 / KBI1 Input Bit 5 UnusedP2-22 PTB6//KBI1P6 Port B Bit 6 / KBI1 Input Bit 6 UnusedP1-17, P1-18 PTB7//KBI1P7 Port B Bit 7 / KBI1 Input Bit 7 • UART flow control RTS input to MCU; jumper required • Connects to REM USB <> UART deviceP2-15, P2-16 PTC0/KBI2P0 Port C Bit 0 / KBI2 Input Bit 0 REM switch matrix; jumper requiredP2-23, P2-24 PTC1/KBI2P1 Port C Bit 1 / KBI2 Input Bit 1 REM switch matrix; jumper requiredP2-20 PTC2/KBI2P2 Port C Bit 2 / KBI2 Input Bit 2 UnusedP2-26 PTC3/KBI2P3 Port C Bit 3 / KBI2 Input Bit 3 UnusedP1-10 PTC4/SPICLK Port C Bit 4 / SPI clock • Unused on REM • Connected to serial FLASH on MRBP1-2 PTC5/SS Port C Bit 5 / SPI slave select • Unused on REM • Connected to serial FLASH on MRBP1-6 PTC6/MISO Port C Bit 6 / SPI MISO • Unused on REM • Connected to serial FLASH on MRBP1-4 PTC7/MOSI Port C Bit 7 / SPI MOSI • Unused on REM • Connected to serial FLASH on MRBP1- 15, P1-16 PTD0/TPM0 Port D Bit 0 / TPM0 signal UnusedP2-27, P2-28 PTD1/TPM1 Port D Bit 1/ TPM1 signal Drives LED4; jumper requiredP1-21, P1-22 PTD2/TPM2 Port D Bit 2 / TPM2 signal • UART flow control CTS output from MCU; jumper required • Connects to REM USB <> UART deviceP2-29, P2-30 PTD3/TPM3 Port D Bit 3 / TPM3 signal • REM IR receiver input; jumper required • Drives timer inputP2-32 PTD4/CMT Port D Bit 4/ CMT output • Not used on REM • Connected to IR blaster on MRBP1-7, P1-8 PTD6/RXD Port D Bit 6 / UART RXD input • UART RXD input to MCU; jumper required • Connects to REM USB <> UART deviceP1-11, P1-12 PTD5/TXD Port D Bit 5 / UART TXD output • UART TXD output from MCU; jumper required • Connects to REM USB <> UART deviceP1-32 PTD7/32MOUT Port D Bit 7 UnusedTable 5-3. 1323x-REM P1 and P2 Pin Header Function Description (continued)1323x-REMHeader PinsMC13233Signal Name Description Comments
1323x Remote Extender Motherboard1323x Development Hardware Reference Manual, Rev. 1.0 5-10 Freescale Semiconductor5.2.4 USB InterfaceFor many applications or demonstrations it is desirable to connect the 1323x-REM to a PC or other device. A USB port is provided with a USB “B” receptacle plug. The port is connected to a FTDI FT232RQ USB <> UART device that appears as a Virtual COM port (VCP) to the PC. PC drivers are available with the module.The USB interface is configured as a "Bus Powered" device and can draw all required power from the USB interface. The device is USB 2.0 full speed compatible. The USB connector is designated as J15. Figure 5-6 shows the connector pinout.Figure 5-6. USB Connector Pinout5.2.5 IR ReceiverThe 1323x-REM provides an IR receiver that accepts IR signals from the RCM or from any IR based remote control devices.• The IR receiver is the TSOP85238TR device (Q3)• 38 kHz carrier frequency• +/- 50 Degree angle of half tranmission distance• Drives the PTD3/TPM3 signal.Figure 5-7 shows the IR receiver schematic.1234S1S21234+D-DGVJ15USB_TY PE_BDATA_PDATA_MV_BUS
1323x Remote Extender Motherboard1323x Development Hardware Reference Manual, Rev. 1.0 Freescale Semiconductor 5-11Figure 5-7. IR Receiver Circuit5.2.6 Pushbutton 2x4 Switch MatrixThe1323x-REM provides an 8 pushbutton 2x4 switch matrix for user application input interface.• The matrix utilizes MC13233 KBI inputs• All switches have interrupt and device wake up capability5.2.7 Blue Indicator LEDsThe1323x-REM provides 4 blue LEDs for user application indicator outputs. Refer to Table 5-3 for listings of the MC13233 outputs that drive the LEDs.
1323x Development Hardware Reference Manual, Rev. 1.0 5-12 Freescale Semiconductor 1323x Remote Extender Motherboard5.3 Schematic, Board Layout, and Bill of MaterialFigure 5-8. 1323x-REM Schematic (1 of 2)5544332211D DC CB BA AV_3V6V_DCV_LEDV_BHLV_MRBV_JACKV_LEDV_DCV_SERV_JACKV_BUSV_SERV_BUSV_IRXV_BATV_USB VCCV_BATV_USBV_BUSV_MAINV_SERDATA_MDATA_PDrawing Title:Size Document Number RevDate: Sheet ofPage Title:ICAP Classification: FCP: FIUO: PUBI:SCH-26117 PDF: SPF-26117 B1323X REMOTE EXTENDER MOTHERBOARDCFriday, October 02, 2009POWER MANAGEMENT44X______Drawing Title:Size Document Number RevDate: Sheet ofPage Title:ICAP Classification: FCP: FIUO: PUBI:SCH-26117 PDF: SPF-26117 B1323X REMOTE EXTENDER MOTHERBOARDCFriday, October 02, 2009POWER MANAGEMENT44X______Drawing Title:Size Document Number RevDate: Sheet ofPage Title:ICAP Classification: FCP: FIUO: PUBI:SCH-26117 PDF: SPF-26117 B1323X REMOTE EXTENDER MOTHERBOARDCFriday, October 02, 2009POWER MANAGEMENT44X______POWER ONEXTERNAL SUPPLY.NEVER SHUNT!!!3.3V BUCK/BOOST REGULATORTO USE TPS63000,REPLACE RESISTORS WITHTHE FOLLOWING VALUES:R45 = 100 OHM, R47 = 1.24MAND POPULATE R46.OUTPUT VOLTAGE WILL BE 3.6VLEDINFRARRED RX3.3V POWER NETWORKMODULAR REFERENCE BOARDR470R470TL2TL2SL14P2T SWITCHSL14P2T SWITCH123456 789101112TL5TL5D11MBR0520LT1GD11MBR0520LT1GTP21TP21R430R430TP20TP201234+D-DGVJ15USB_TYPE_B1234+D-DGVJ15USB_TYPE_B1234S1S2C4210UFC4210UFC4310UFC4310UFR46200KDNPR46200KDNPTP27TP27D12MBR0520LT1GD12MBR0520LT1GF10.5AF10.5A1 2C410.01UFC410.01UFBH4125BH4125C330.1UFC330.1UFFID2FIDFID2FIDL460OHML460OHM1 2BT1BATTERY HOLDERBT1BATTERY HOLDER12TL3TL3Q4SI2305Q4SI2305132R400R400D13MBR0520LT1GD13MBR0520LT1GTP29TP29R360R360D9MBR0520LT1GD9MBR0520LT1GR450R450BH3125BH3125TL4TL4TP25TP25R39330R39330C3210UFC3210UFFID1FIDFID1FIDD8MBR0520LT1GD8MBR0520LT1GBH2125BH2125LED5REDLED5RED21BH1125BH1125TP19TP19TP24TP24J14HDR 1X2J14HDR 1X212TL1TL1R384.7KR384.7KC404.7uFC404.7uFL3 3.3uHL3 3.3uH1 2C390.1UFC390.1UFR4110KR4110KD10MBR0520LT1GD10MBR0520LT1GFID3FIDFID3FIDTP23TP23U8TPS63001U8TPS63001EN6GND9L14L2 2PS/SYNC7VOUT 1VIN5VINA8FB 10PGND 3PPAD 11R350R350
1323x Remote Extender Motherboard1323x Development Hardware Reference Manual, Rev. 1.0 Freescale Semiconductor 5-13 Figure 5-9. 1323x-REM Schematic (2 of 2)5544332211D DC CB BA AV_3V6V_DCV_LEDV_BHLV_MRBV_JACKV_LEDV_DCV_SERV_JACKV_BUSV_SERV_BUSV_IRXV_BATV_USB VCCV_BATV_USBV_BUSV_MAINV_SERDATA_MDATA_PDrawing Title:Size Document Number RevDate: Sheet ofPage Title:ICAP Classification: FCP: FIUO: PUBI:SCH-26117 PDF: SPF-26117 B1323X REMOTE EXTENDER MOTHERBOARDCFriday, October 02, 2009POWER MANAGEMENT44X______Drawing Title:Size Document Number RevDate: Sheet ofPage Title:ICAP Classification: FCP: FIUO: PUBI:SCH-26117 PDF: SPF-26117 B1323X REMOTE EXTENDER MOTHERBOARDCFriday, October 02, 2009POWER MANAGEMENT44X______Drawing Title:Size Document Number RevDate: Sheet ofPage Title:ICAP Classification: FCP: FIUO: PUBI:SCH-26117 PDF: SPF-26117 B1323X REMOTE EXTENDER MOTHERBOARDCFriday, October 02, 2009POWER MANAGEMENT44X______POWER ONEXTERNAL SUPPLY.NEVER SHUNT!!!3.3V BUCK/BOOST REGULATORTO USE TPS63000,REPLACE RESISTORS WITHTHE FOLLOWING VALUES:R45 = 100 OHM, R47 = 1.24MAND POPULATE R46.OUTPUT VOLTAGE WILL BE 3.6VLEDINFRARRED RX3.3V POWER NETWORKMODULAR REFERENCE BOARDR470R470TL2TL2SL14P2T SWITCHSL14P2T SWITCH123456 789101112TL5TL5D11MBR0520LT1GD11MBR0520LT1GTP21TP21R430R430TP20TP201234+D-DGVJ15USB_TYPE_B1234+D-DGVJ15USB_TYPE_B1234S1S2C4210UFC4210UFC4310UFC4310UFR46200KDNPR46200KDNPTP27TP27D12MBR0520LT1GD12MBR0520LT1GF10.5AF10.5A1 2C410.01UFC410.01UFBH4125BH4125C330.1UFC330.1UFFID2FIDFID2FIDL460OHML460OHM1 2BT1BATTERY HOLDERBT1BATTERY HOLDER12TL3TL3Q4SI2305Q4SI2305132R400R400D13MBR0520LT1GD13MBR0520LT1GTP29TP29R360R360D9MBR0520LT1GD9MBR0520LT1GR450R450BH3125BH3125TL4TL4TP25TP25R39330R39330C3210UFC3210UFFID1FIDFID1FIDD8MBR0520LT1GD8MBR0520LT1GBH2125BH2125LED5REDLED5RED21BH1125BH1125TP19TP19TP24TP24J14HDR 1X2J14HDR 1X212TL1TL1R384.7KR384.7KC404.7uFC404.7uFL3 3.3uHL3 3.3uH1 2C390.1UFC390.1UFR4110KR4110KD10MBR0520LT1GD10MBR0520LT1GFID3FIDFID3FIDTP23TP23U8TPS63001U8TPS63001EN6GND9L14L2 2PS/SYNC7VOUT 1VIN5VINA8FB 10PGND 3PPAD 11R350R350
1323x Remote Extender Motherboard1323x Development Hardware Reference Manual, Rev. 1.0 5-14 Freescale SemiconductorFigure 5-10. 1323x-REM PCB Component Location (Top View)Figure 5-11. 1323x-REM PCB Test Points
1323x Remote Extender Motherboard1323x Development Hardware Reference Manual, Rev. 1.0 Freescale Semiconductor 5-15Figure 5-12. 1323x-REM PCB Layout (Top View)Figure 5-13. 1323x-REM PCB Layout (Bottom View)
1323x Remote Extender Motherboard1323x Development Hardware Reference Manual, Rev. 1.0 5-16 Freescale Semiconductor5.3.1 1323x-REM Bill of MaterialsTable 5-4. Bill of MaterialsItem Qty. Reference Value Description Mfg. Name Part Number1 4 BH1, BH2, BH3, BH4125 NON-PLATED MOUNTING HOLE 125 DRILL / 160 KEEPOUT NO PART TO ORDER21BT1 BATTERY HOLDERBATTERY HOLDER 2XAA TH KEYSTONE ELECTRONICS24623 2 C23,C24 15PF CAP CER 15PF 50V 5% C0G 0402KEMET C0402C150J5GAC4 4 C25,C30,C33, C390.1UF CAP CER 0.1UF 16V 10% X7R 0402MURATA GRM155R71C104KA88D5 3 C32,C42,C43 10UF CAP CER 10UF 10V 10% X7R 0805Murata GRM21BR71A106KE51L6 1 C40 4.7uF CAP CER 4.7UF 10V 10% X5R 0603TAIYO YUDEN LMK107BJ475KA-T7 1 C41 0.01UF CAP CER 0.01UF 10V 20% X7R 0402AVX 0402ZC103MAT2A8 1 C53 2.2UF CAP CER 2.2UF 6.3V 20% X5R 0402MURATA GRM155R60J225ME15D9 6 D8,D9,D10,D11,D12,D13MBR0520LT1GDIODE SCH 0.5A 20V SOD-123ON SEMICONDUCTORMBR0520LT1G10 3 FID1,FID2,FID3 FID FIDUCIAL 060 MIL PAD W/120 SOLDERMASK AND 040 MIL PAD W/90 MIL SOLDERMASK NO PART TO ORDERGENERIC FID-04011 1 F1 0.5A FUSE FAST 0.5A 63V SMT 1206LITTELFUSE 0437.500WR12 1 J8 CON_2X10CON 2X10 SKT TH 100MIL CTR 335H AU 104LSAMTEC SSW-110-01-G-D13 1 J9 CON_2X9 CON 2X9 SKT TH 100MIL SP 335H AU 194LSAMTEC SSW-109-02-G-D14 1 J14 HDR_1X2 HDR 1X2 TH 100MIL SP 375H AUTYCO ELECTRONICS826629-215 1 J15 USB_TYPE_BCON 2X2 USB_TYPE_B SKT RA SHLD TH 2.5MM SP 453H AUTYCO ELECTRONICS292304-216 4 LED1,LED2,LED3,LED4BLUE LED BLUE SGL 20MA SMT 0805LITE ON LTST-C171TBKT-5A17 1 LED5 RED LED RED CLEAR SGL 30MA SMT 0805LITE ON LTST-C171KRKT
1323x Remote Extender Motherboard1323x Development Hardware Reference Manual, Rev. 1.0 Freescale Semiconductor 5-1718 1 L3 3.3uH IND PWR 3.3UH@100KHZ 3.3A 20% SMTVISHAY INTERTECHNOLOGYIHLP2020BZER3R3M0119 1 L4 60OHM IND FER BEAD 60OHM@100MHZ 500MA -- 0603MURATA BLM18PG600SN1_20 2 P1,P2 HDR_2X16HDR 2X16 TH 100MIL CTR 330H AU 100LSAMTEC TSW-116-07-S-D21 1 Q3 TSOP85238TRTRAN PHOTO 0.45MA 5.5V 950NM SMTVISHAY INTERTECHNOLOGYTSOP85238TR22 1 Q4 SI2305 TRAN PMOS PWR 4.1A 8V SOT23VISHAY INTERTECHNOLOGYSI2305ADS-T1-GE323 4 R19,R20,R21,R221K RES MF 1.0K 1/16W 5% 0402 VISHAY INTERTECHNOLOGYCRCW04021K00JNED24 4 R23,R24,R25,R26390 RES MF 390 OHM 1/16W 5% 0402BOURNS CR0402-JW-391GLF25 2 R33,R39 330 RES MF 330 OHM 1/16W 5% 0402VISHAY INTERTECHNOLOGYCRCW0402330RJNED26 6 R35,R36,R40,R43,R48,R490 RES TF ZERO OHM 1/16W RC0402VISHAY INTERTECHNOLOGYCRCW04020000ZS27 1 R38 4.7K RES MF 4.7K 1/16W 5% 0402 SMEC RC73L2Z472JTF28 1 R41 10K RES MF 10K 1/16W 5% 0402 VISHAY INTERTECHNOLOGYCRCW040210K0JNED29 1 R45 100 RES MF 100 OHM 1/16W 5% 0402VISHAY INTERTECHNOLOGYCRCW0402100RJNED30 1 R46 200K RES MF 200K 1/16W 5% 0402 YAGEO AMERICA RC0402JR-07200KL31 1 R47 1.24M RES MF 1.24M 1/16W 1% 0402VISHAY INTERTECHNOLOGYCRCW04021M24FKED32 1 SL1 4PDT SWITCHSW 4PDT SLD TH RA 30V 100MA --TYCO ELECTRONICS1-1437575-133 8 SW1,SW2,SW3,SW4,SW5,SW6,SW7,SW8PB switch SW SMT 4.0MM FMS 0.1A MAX 16V MAX ROHS COMPLIANTBOURNS 7914J-1-000ETable 5-4. Bill of MaterialsItem Qty. Reference Value Description Mfg. Name Part Number
1323x Remote Extender Motherboard1323x Development Hardware Reference Manual, Rev. 1.0 5-18 Freescale Semiconductor34 15 TP13,TP14,TP15,TP16,TP19,TP20,TP21,TP23,TP24,TP25,TP27,TP29,TP30,TP31,TP32TPAD_040 TEST POINT PAD 40MIL DIA SMT, NO PART TO ORDERNOTACOMPONENTNOTACOMPONENT35 1 U4 FT232RQ IC XCVR USB TO UART CTLR 3.3-5.25V QFN32FUTURE TECH-NOLOGY DEVICES INTER-NATIONAL LTD.FT232RQ36 1 U8 TPS63001IC LIN DCDC SYNC 3.3V OUTPUT 1250-1800KHZ 1.8-5.5V QFN-10TEXAS INSTRU-MENTSTPS63001DRCTTable 5-4. Bill of MaterialsItem Qty. Reference Value Description Mfg. Name Part Number
1323x Development Hardware Reference Manual, Rev. 1.0 Freescale Semiconductor 6-1Chapter 6 PCB Manufacturing SpecificationsThis chapter provides the specifications used to manufacture the 1323x Development hardware printed circuit boards (PCB) described in this manual.The 1323x Development hardware PCBs must comply with the following:• The PCB must comply with Perfag10/3C (http://www.perfag.dk/Uk/ukindex.htm)• The PCB manufacturer’s logo is required• The PCB production week and year code is required— The manufacturer’s logo and week/year code must be stamped on the back of the PCB solder mask— The PCB manufacturer can not insert text on the PCB either in copper or in silkscreen without written permission from Freescale Semiconductor, Inc.• The required Underwriter’s Laboratory (UL) Flammability Rating— The level is 94V-0 (http://www.ul.com/plastics/flame.html)— The UL information must be stamped on the back of the PCB solder maskNOTE• A complete set of design files is available for the 1323x Development hardware at the Freescale web site (http:www.freescale.com/802154) under reference designs. It is recommended that this design or one of a number of other reference designs be used as a starting point for a custom application.• The Freescale IEEE 802.15.4 / ZigBee Package and Hardware Layout Considerations Reference Manual, (ZHDCRM) is also available at the same web site to provide additional design guidance.6.1 Single PCB ConstructionThis section describes individual PCB construction details.• The MRB and RCM PCBs are four-layer, multi layer designs• The REM PCB is a two layer design• The PCBs contains no blind, buried, or micro vias• PCB data:— MRB Size: Approximately 51 x 51mm (2.01 x 2.01 inches)— RCM Size: Approximately 86 x 178 mm (3.4 x 7.0 inches)— REM Size: Approximately 79 x 79 mm (3.1 x 3.1 inches)
PCB Manufacturing Specifications1323x Development Hardware Reference Manual, Rev. 1.0 6-2 Freescale Semiconductor— MRB, RCM and REM Final thickness (Cu/Cu): 0.34 mm (0.8 inches) +/- 10% (excluding solder mask)The following table defines some of the layers of the completed PCB. The artwork identification refers to the name of the layer in commonly used terms.The 1323x MRB contains high frequency 2.4 GHz RF circuitry. As a result, RF component placement, line geometries and layout, and spacing to the ground plane are critical parameters. As a result, BOARD STACKUP GEOMETRY IS CRITICAL. Dielectric and copper thicknesses and spacing must not be changed; follow the stackup (see Figure 6-1) information is provided with the reference design.Table 6-1. MRB Layer by Layer OverviewLayer Artwork Identification File Name1 Silkscreen Top SILK_TOP.art2 Top Layer Metal TOP.art3 Ground Layer GND.art4 Power Layer PWR.art5 Bottom Layer Metal BOTTOM.art6 Silkscreen Bottom SILK_BOTTOM.artTable 6-2. RCM Layer by Layer OverviewLayer Artwork Identification File Name1 Silkscreen Top SILK_TOP.art2 Top Layer Metal TOP.art3 Ground Layer GND.art4 Power Layer PWR.art5 Bottom Layer Metal BOTTOM.art6 Silkscreen Bottom SILK_BOTTOM.artTable 6-3. REM Layer by Layer OverviewLayer Artwork Identification File Name1 Silkscreen Top SILK_TOP.art2 Top Layer Metal TOP.art3 Bottom Layer Metal BOTTOM.art4 Silkscreen Bottom SILK_BOTTOM.art
PCB Manufacturing Specifications1323x Development Hardware Reference Manual, Rev. 1.0 Freescale Semiconductor 6-3Figure 6-1. MRB PCB Stackup Cross-Section (Four Layer)• Solder mask is required• Silk screen is required6.2 PanelizationThe panel size can be negotiated depending on production volume.6.3 MaterialsThe PCB composite materials must meet the following requirements:• Laminate - The base laminate material (laminate) must be FR4. If the laminate material were changed the RF electrical characteristics may change and degrade RF performance.• Copper Foil - — Top and Bottom copper layers must be 1 oz. copper— Interior layers must be 1/2 oz. copper• Plating - All pad plating must be Hot Air Levelling (HAL)6.4 Solder MaskThe solder mask must meet the following requirements: • Solder mask type: Liquid Film Electra EMP110 or equivalent• Solder mask thickness: 10 – 30 µmDielectricDielectricDielectricMetal 1Metal 2Metal 3Metal 4
PCB Manufacturing Specifications1323x Development Hardware Reference Manual, Rev. 1.0 6-4 Freescale Semiconductor6.5 Silk ScreenThe silk screen must meet the following requirements:• Silkscreen color: White• Silkscreen must be applied after application of solder mask if solder mask is required• The silkscreen ink must not extend into any plated-thru-holes• The silk screen must be clipped back to the line of resistance6.6 Electrical PCB Testing• All PCBs must be 100 percent tested for opens and shorts• Impedance Measurement - An impedance measurement report is not mandatory6.7 Packaging Packaging for the PCBs must be the following requirements:• Finished PCBs must remain in panel• Finished PCBs must be packed in plastic bags that do not contain silicones or sulphur materials. These materials can degrade solderability.6.8 Hole Specification/Tool TableSee the ncdrill-1-4.tap file included with the Gerber files and the FAB-23451.pdf file.6.9 File DescriptionFiles included with the download include Design, Gerber and PDF files. Gerber files are RS-374x format. Not all files included with the Gerber files are for PCB manufacturing.PDF files included are:• FAB-2611x.pdf — Board fabrication drawing• GRB-2611x.pdf — Metal layers, solder mask, solder paste and silk screen• SPF-2611x.pdf — SchematicDesign files are in Allegro format with OrCAD schematic capture.

Navigation menu