Food Automation Service Techniques XWIRE-GATEWAY Food quality and supply chain monitor equipment User Manual Letter Size

Food Automation - Service Techniques, Inc. Food quality and supply chain monitor equipment Letter Size

UserManual.wiki >

Food Automation Service Techniques >

XWIRE GATEWAY User Manual

User Manual

Installation GuideXwireTM Universal SmartAdapter forCommunications-Enabled AppliancesXwireTM SmartBezel Adapter for Process ControllersXwireTM SmartGateway PC AdapterSmartAdapterSmartBezelSmartGateway24/7 Toll-Free Technical Support1-866-840-4271(from the U.S., Canada and the Caribbean)Direct, Inc.www.MySCK.comSAVE these instructionsfor future reference.

2© 2008 SCK Direct, Inc. 229-51316 Rev F www.MySCK.comXwireTM Direct, Inc.NOTICESSCK Direct, Inc. is not liable for any use of product not in accor-dance with SCK Direct, Inc.’s installation and operationinstructions.BEFORE USING THIS EQUIPMENT, OR FOR ANY QUESTIONS ONTHE OPERATION OF THE APPLIANCE, CONSULT AND FOLLOW ALLINSTRUCTIONS AND SAFETY WARNINGS FOUND IN THE APPLI-ANCE OPERATOR’S MANUAL SUPPLIED FROM THEMANUFACTURER OF THE APPLIANCE.CLEANINGUsing a clean damp cloth, wipe down the products when neces-sary using a commercial quality foodservice-approved detergent.DO NOT IMMERSE.NEVER use chemical or abrasive cleaners on SCK products.TOOLS REQUIRED FOR INSTALLATIONFlat screwdriver (for SmartBezel)Pliers (for SmartBezel)Phillips screwdriver (for SmartAdapter)Drill bit: 3/16” if using anchor. #50 if installing into metal (forSmartAdapter)Changes or modifications not expresslyapproved by SCK Direct, Inc. could void themanufacturer’s warranty and the user'sauthority to operate the equipment.NOTE: This equipment has been tested and found to comply withthe limits for a Class B digital device, pursuant to Part 15 of the FCCRules. These limits are designed to provide reasonable protectionagainst harmful interference in a residential installation. Thisequipment generates, uses and can radiate radio frequency ener-gy and, if not installed and used in accordance with theinstructions, may cause harmful interference to radio communica-tions. However, there is no guarantee that interference will notoccur in a particular installation. If this equipment does causeharmful interference to radio or television reception, which can bedetermined by turning the equipment off and on, the user isencouraged to try to correct the interference by one or more ofthe following measures:Reorient or relocate the receiving antenna.Increase the separation between the equipment andreceiver.Connect the equipment into an outlet on a circuit differentfrom that to which the receiver is connected.Consult the dealer for help.TABLE OF CONTENTSInstallation: Wireless SmartGateway Adapter . . . . . . . . . . . . . .3Installation: SmartBezel Adapterfor FAST VC-210 & FAST EM-99 Controllers . . . . . . . . .4Installation: Universal SmartAdapterforFASTTRACKERTimers..........................5Installation: Universal SmartAdapterforFryers&Ovens.................................5Light Bar and LED Status Charts . . . . . . . . . . . . . . . . . . . . . . . . . . .6Troubleshooting..........................................7ChangingtheDefaultPANID .............................7

3© 2008 SCK Direct, Inc. 229-51316 Rev F www.MySCK.cominstallation guideXwire WirelessSmartGateway AdapterREQUIRED PARTS(A) Xwire Wireless SmartGateway AdapterSCK Part No. 231-60207-01(B) USB Cable, 5MSCK Part No. 141-15734INSTALLATION1. Connect USB cable to the communication port on the SmartGateway.2. Power off the PC and connect the SmartGateway to an available USB portusing the USB cable.NOTE: It’s important to power down for proper configuration.3. Verify the LED sequence on the SmartGateway is correct per your applica-tion by referring to the charts on page 6.STEP 1The SmartGateway should be installed first.

4© 2008 SCK Direct, Inc. 229-51316 Rev F www.MySCK.comXwireTM Direct, Inc.Xwire SmartBezel Adapter forFAST VC-210 & FAST EM-99CONTROLLERSREQUIRED PARTS(1) Xwire SmartBezel AdapterSCK Part No. 231-60206-01(2) Self-tapping Connectors (included)SCK Part No. 141-51026Qty. 2INSTALLATION1. Locate wires numbered 1 and 3 in the 9-pin connector onthe FAST VC-210 or FAST EM-99 controllers.2. Clamp self-tapping connector to these wires to provide a24VAC output for the SmartBezel.3. Connect the two spade terminals to the pair coming fromthe SmartBezel.4. Connect the 3-pin Molex connector on the SmartBezel tothe 3-pin Molex on the controller.5. Position the SmartBezel onto thefront of the FAST Controller.Carefully place the five SmartBezelwires into the channel on theFAST Controller.6. Install the FAST Controller on thefryer and verify the LED sequenceis correct per your application byreferring to the charts on page 6.The FAST Controller is now ready to be used as an SCK Xwirewireless device.STEP 2The SmartBezel Adapter

6© 2008 SCK Direct, Inc. 229-51316 Rev F www.MySCK.comXwireTM Direct, Inc.LED Color LED Blink Rate DescriptionORANGE 2 sec ON,2 sec OFFDevice cannot communi-cate with the SCK deviceafter already connecting tothe wireless network.ORANGE Very Fast Device is initializing.GREEN Solid OnDevice has found aSmartGateway and is nowconnected to the network.GREEN Very FastDevice is waiting for areply for data sent toanother device.STRONGAll light bars are lit RED.GOODAt least two light bars are lit RED.WEAKOnly one light bar is lit RED.NONENo light bars are lit RED.STATUS LED CHARTSIGNAL STRENGTH INDICATORS LIGHT BARSThe SCK Xwire status indicator consists of three colors (Green, Red andOrange) to visually indicate transmission strength and operating status tothe operator.See the charts below for details.Light Bars and Status LEDHow Do I Know if It’s Working?Under normal operating conditions, the status LED will be solidgreen and all or some of the signal strength LEDs (light bars) willbe lit depending on signal strength. In most cases, you’ll see thegreen status LED lit solid while the signal strength light barschange from time to time.

7© 2008 SCK Direct, Inc. 229-51316 Rev F www.MySCK.cominstallation guideTROUBLESHOOTING / LED CODESLED Action Description SolutionAll LEDs blink on andoff simultaneouslyevery 500ms.Device has detected a multiple SCK addressconflict and is waiting for resolution (cur-rently participating as address 30)1. Verify that all enabled controls are set to adifferent SCK address.All LEDs blink in twoshort bursts followedby one second of offtime.The device is connected to a wireless net-work but not to an SCK-enabled control.1. Make sure device is SCK compatible.2. Make sure communication port is connected.3. Check SCK wiring.4. Install it on a known working appliance.All LEDs strobe. Device is searching for a SmartGateway. 1. Verify the SmartGateway is turned ON.2. Install the Xwire device closer to theSmartGateway.3. A SmartRepeater may need to be added toextend the range. Contact your SCK SalesRepresentative.Status LED flashesgreen/orange continu-ously.The radio on the SmartGateway has beenturned OFF.1. Contact your local Helpdesk, or SCKSupport at 1-866-840-4271Orange LED blinks ONfor 2 seconds, thenOFF for 2 seconds.Device is attempting to resolve an SCKaddress conflict by changing to address 30,but there is already another device on theSCK network using address 30.1. Verify that all enabled controls are set to adifferent SCK address.Device cannot communicate with the radio. 1. Try cycling power to the unit OFF, then ON.2. Contact SCK Support.Changing the Default PAN ID(Personal Area Network Identification)The factory default PAN ID is 1. Should your SCK Xwiredevice experience interference that prevents it from workingproperly, the network PAN ID may be overridden and selectedmanually:Locating the PAN ID Button onthe Xwire DevicesXwire SmartBezel -- PAN ID button is located in therear of the unit in the slot immediately below themounting screw locationXwire Universal SmartAdapter -- PAN ID button islocated on the back of the unit in the access waylabeled ChannelXwire Wireless SmartGateway -- PAN ID button islocated on the right-hand side of the unit in the openaccess wayTHE FOLLOWING IS INCLUDED FOR REFERENCE ONLY AND SHOULD BE PERFORMED ONLY BYAN SCK CERTIFIED TECHNICIAN.1) With the device powered ON, press the PAN ID buttonand note the LED pattern that is illuminated. Thispattern indicates the default PAN ID.2) Press the PAN ID button to change to the next availablePAN ID. The PAN ID button must be pressed within 2-seconds of a previous button press or the device willtimeout and return to its previous mode).3) The last selection before the timeout occurs will be theselected PAN ID. If a PAN ID selection differs from theprevious selection, the Xwire device will remove itselffrom its current network, reconfigure, and join/start thenetwork with the new PAN ID.NOTE: If the PAN ID button is not pressed within 10-sec-onds, the unit will begin scanning for an availablenetwork and you must wait for the scanning sequence tocomplete before the PAN ID button is enabled.4) You must set the PAN ID on all Xwire devices to the samePAN ID to allow the devices to communicate properly.

Direct, Inc.Thank You for ChoosingSCK Direct, Inc!SCK Direct, Inc.905 Honeyspot RoadStratford, CT 06615 USA+1 203.377.4174 voice+1 203.377.8187 fax1.866.840.4271 toll-free sales & helpdeskwww.MySCK.com; info@mysck.com229-51316 Rev. F© 2008 SCK Direct, Inc.Printed in the USA19SEP2008TroubleshootingShould you experience problems installing your SCK Xwire prod-ucts, or any aspect of your SCK Direct, Inc. services, please contactthe SCK HelpDesk toll-free at 1.866.840.4271.Optional SCK System ComponentsSCK has a variety of optional accessories to help you completeyour kitchen automation:SCK Kitchen Advisor Information ServerSCK Remote Input DeviceSCK KSM Kitchen Status MonitorSCK-Enabled Appliance ControllersSCK Wireless (XwireTM) Appliance InterfaceSCK Wireless (XwireTM) Temperature/Door SmartSensorTMSCK Wireless (XwireTM) SmartGatewaySCK Wired BackboneFor additional information on any of these accessories, or torequest Technical Specification Sheets, please contact your SCKRepresentative or contact SCK Customer Support toll-free at1-866-840-4271 (Monday-Friday, 8:00 a.m. to 5:00 p.m. EST).This document contains confidential information. The dissemina-tion, publication, copying, or duplication of this document or thesoftware described herein without prior written authorization isstrictly prohibited.Specifications subject to change without notice.(FAST.)® is a registered trademark of Food Automation - ServiceTechniques, Inc.Smart Commercial Kitchen and SCK are registered trademarks ofTechnology Licensing Corporation.SCK Direct, Inc. products are covered under U.S. and foreignpatents, plus patents pending.WARRANTYSCK Direct, Inc. warrants all new Xwire hardware for 1 year from thedate of purchase. SCK Direct, Inc. warrants all other items for a peri-od of 90 days unless otherwise stated at the time of purchase.