Firetide 4600-1 Hot Point 4600 (outdoor unit) User Manual

Firetide Inc. Hot Point 4600 (outdoor unit) Users Manual

Users Manual

Wireless Access Point User GuideHotPoint 4500 Indoor Access Point   HotPoint 4600 Outdoor Access Point
ii  Wireless Access Point User Guide This symbol is intended to alert the user to the presences of non-insulated  dangerous  voltage  that  may  be  of  sufficient magnitude to constitute a risk of lethal electric shock to per-sons.This symbol is intended to alert the user to the presence of im-portant operating, maintainance, and servicing instructions. Failing to comply with this instruction may result in electrical shock.This symbol is intended to alert the user to the presence of im-portant operating, maintainance, and servicing instructions. Failing to comply with this instruction may result in a hazard.Do not open the coverDangerous voltages inside.No serviceable parts inside.Refer to qualified service personnel.Unit must be disconnected from power prior to servicing.Unit has tamper-evident labeling that indicates when the cover has been removed.•••••Safety InstructionsThe HotPoint node must be installed by a qualified professional. Failure to install this equipment properly may result in equipment dam-age, personal injury, or death. Explanation of Graphic Symbols Caution! Risk of electric shock!  POWER LINES CAN BE LETHALDo not install the HotPort outdoor mesh node where possible contact with power lines can be made. Antennas, poles, towers, guy wires, or cables may lean or fall and contact these lines. People may be injured or killed if they are touching or  holding any  part of equipment when it contacts electric lines. Make sure there is NO possibility that equipment or personnel can come in contact directly or indirectly with power lines.ASSUME ALL OVERHEAD LINES ARE POWER LINESThe horizontal distance from a tower, pole or antenna to the nearest power line should be at least twice the total length of the pole/antenna combina-tion. This will ensure that the pole will not contact power if it falls either during or after installation.SURVEYING THE SITELook over the entire site before beginning any installation and anticipate possible hazards. Never assume anything without checking it out for your-self! Don’t take shortcuts!
  HotPoint Wireless Access Point  iii TO  AVOID  FALLING,  USE  SAFE  PROCEDURES  WHEN  WORKING  AT HEIGHTS ABOVE GROUNDSelect equipment locations that will allow safe and simple installation.Don’t work alone. A friend or co-worker can save your life if an accident happens.Don’t attempt repair work when you are tired. Not only will you be more careless, but your primary diagnostic tool - deductive reasoning - will not be operating at full capacity. Use  approved  non-conducting  ladders,  shoes,  and  other  safety  equip-ment. Make sure all equipment is in good repair.If a tower or pole begins falling, don’t attempt to catch it. Stand back and let it fall. If anything such as a wire or pole does come in contact with a power line, DON’T TOUCH IT OR ATTEMPT TO MOVE IT. Instead, save your life by calling the power company.Don’t attempt to erect antennas or towers on windy days.MAKE SURE ALL TOWERS AND POLES ARE SECURELY GROUNDED, AND ELEC-TRICAL CABLES CONNECTED TO ANTENNAS  HAVE LIGHTNING  ARRESTORS. This will help prevent fire damage or human injury in case of lightning, static build-up, or short circuit within equipment connected to the an-tenna.  The  HotPort  outdoor  node has  built-in lightning  protection. Be sure that any other equipment connected to the HotPort node also has the same level of protection.The base of the antenna pole or tower must be connected directly to the building protective ground or to one or more approved grounding rods, using 10 AWG ground wire and corrosion-resistant connectors. Refer to the National Electrical Code for grounding details.••••••••••IF AN ACCIDENT SHOULD OCCUR WITH THE POWER LINESDON’T TOUCH THAT PERSON, OR YOU MAY BE ELECTROCUTED.Use a non-conductive dry board, stick, or rope to push or drag them so they no longer are in contact with electrical power.Once they are no longer contacting electrical power, administer CPR if you are certified. Immediately have someone call for medical help.••••
iv  Wireless Access Point User Guide Firetide Limited End User Product WarrantyPursuant to all provisions described herein, Firetide products are warranted for one (1) year from the date of purchase against defects in the build materi-als and workmanship. Firetide also warrants that the Software will materially conform to the documentation supplied by Firetide with the Software. In the event that the Software fails to materially conform to the documentation and an authorized Firetide reseller is notified in writing of such failure within the warranty period, Firetide or its reseller shall use commercially reasonable ef-forts to promptly correct the nonconformity. Firetide does not warrant that the use of the Software will be uninterrupted or error free. Firetide does not warrant that the Products will meet any requirements or specifications of any End User Customer. This warranty applies to the entire Firetide product, in-cluding antennas and the AC power adapter.The  above  warranties  are  void  if  the  alleged  defect  cannot  be  verified  by Firetide or if, as determined by Firetide, the product failure was due to tam-pering,  abuse,  misuse,  accident,  shipping,  handling,  or  storage;  or  if  the product has been installed, used, or maintained in a manner not described in the product user manual; or if the product has been altered in any way; or if product serialization has been altered. Any attempt to disassemble or repair the product by anyone other than Firetide immediately voids this warranty.This warranty applies only to the original End User purchaser of the product and may not be transferred to any other individual or entity.THE FOREGOING ARE THE EXCLUSIVE WARRANTIES APPLICABLE TO THE PRODUCT INCLUDING THE SOFTWARE, AND THE EXCLUSIVE REMEDY FOR DEFECTS IN THE PRODUCT. FIRETIDE DISCLAIMS ALL OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED, STATUTORY OR OTHERWISE, INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF  MERCHANTABILITY,  NON-INFRINGEMENT  OR  FITNESS  FOR  A PARTICULAR PURPOSE. SOME LAWS DO NOT ALLOW THE EXCLUSION OF IMPLIED WARRANTIES SO TO THAT EXTENT THIS LIMITATION MAY NOT APPLY TO YOU.In no event will Firetide be liable for any special, incidental, consequential, punitive or indirect damages whatsoever (including, without limitation, dam-ages for loss of profits, business interruption, loss of information, or other pecuniary loss) arising out of the use or inability to use the product or the performance, interruption or failure of the product, irrespective of the cause of action, even if Firetide has been advised of the possibility of such damages. Firetide’s cumulative  liability  for all  claims  arising  out  of  or  in  connection with this warranty will not exceed the amount paid by the original End User purchaser to purchase the product. The amounts payable for the product are based in part on these limitations and these limitations shall apply notwith-standing the failure of essential purpose of any remedy. Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so to that extent the above limitations or exclusions may not apply to you.By using the product the original End User purchaser agrees to and is bound by these terms and conditions.In the event that a product fails to meet this warranty and Firetide’s autho-rized reseller is notified in writing of such failure within the warranty period, Firetide shall, at its own discretion, either repair the product or replace it with the  same or a functionally-equivalent product free of charge.  Replacement products may contain refurbished materials in whole or in part. Firetide will honor this warranty provided the product is returned through an authorized Firetide reseller or dealer with shipping charges prepaid, along with a proof of purchase describing the original purchase date and product serial numbers if applicable. The authorized reseller must acquire a Return Materials Autho-rization (RMA) number from Firetide prior to returning any product. Firetide does not accept  shipments  of defective products  without  shipping charges prepaid.
  HotPoint Wireless Access Point  v Indoor Manual ContentsIntroduction.................................................................................................................................................................................................................1Firetide HotPoint Wireless Access Point Family .............................................................................................................................................................1HotPoint Access Point Features .................................................................................................................................................................................2HotPoint + HotPort Network Applications ................................................................................................................................................................... 2HotPoint + HotPort Features ....................................................................................................................................................................................3Indoor Unit - Unpacking and Installation ...........................................................................................................................................................................5Outdoor Unit - Unpacking and Installation .........................................................................................................................................................................6Understanding APs, AP Groups, VAPs, & VAP Groups ......................................................................................................................................................8Software Installation ........................................................................................................................................................................................... 10Basic Setup Sequence ........................................................................................................................................................................................... 10Software Configuration ......................................................................................................................................................................................... 11AP Node Commands .............................................................................................................................................................................................. 12AP Group Commands ............................................................................................................................................................................................. 13Physical AP Radio Settings ..................................................................................................................................................................................... 14VAP Group Configuration ....................................................................................................................................................................................... 15VAP Settings ....................................................................................................................................................................................................... 16VAP Group Settings .............................................................................................................................................................................................. 17Advanced Features ............................................................................................................................................................................................... 21Country Code Assignment ...................................................................................................................................................................................... 21Appendix A - HotPoint Features and Specifications ............................................................................................................................................................. 22Appendix D—Regulatory Notices..................................................................................................................................................................................... 24USA .................................................................................................................................................................................................................. 24Canadian Compliance Statement ............................................................................................................................................................................. 25
vi  Wireless Access Point User Guide
  HotPoint Wireless Access Point  1 IntroductionFiretide HotPoint Wireless Access Point FamilyFiretide’s  HotPoint family  of  wireless access points  are the newest  addi-tion to the company’s HotPort line of high performance wireless mesh net-working products. The HotPoint access points provide an enterprise-class wireless access solution  and can be  used as full-function  standalone  ac-cess points, or as part of an integrated, triple-play wireless mesh network. Available in indoor and outdoor models, they include a high power, multi-spectrum extended range radio, multiple antenna options, robust security features, and multiple ESSID support.The Firetide™ HotPoint™ Wireless Access Points (AP) are companion units to the Firetide HotPort™ High-Performance Mesh Network. Each AP allows 802.11b and 802.11g  wireless clients to connect to the Firetide  Wireless Mesh  network.  Such  clients  include  laptops,  wireless  security  cameras, VoIP phones, and portable terminal and POS devices.The  Firetide  mesh  network  itself  provides  a  high-capacity,  self-healing wireless mesh for indoor and outdoor networks. The HotPort system allows standard Ethernet devices to operate on the wireless backbone, creating secure  and  reliable  wireless  networks  for  video  surveillance,  voice,  and data. HotPoint APs and HotPort nodes can be managed together as a sys-tem with Firetide’s HotView mesh management software.HotPoint 4500 indoor APs are plenum-rated and can be mounted securely to a wall, ceiling, or countertop using an optional mounting bracket. Each HotPoint indoor node includes antennas.HotPoint 4600 Outdoor  APs  feaure NEMA4X/IP66-rated  aluminum enclo-sures, and can be powered over Ethernet.Firetide’s modular access point design offers several benefits. Among them are:A HotPoint access point can be mounted to a Firetide mesh node to pro-vide enterprise class Wi-Fi access to any indoor or outdoor location, with-out the need for backhaul cabling. A HotPoint access point can connect directly to a conventional wired in-frastructure. This eliminates the need to install a Firetide mesh node in locations where wired connectivity is readily available, while preserving the unified management capabilities for all access points. Because the access points and  mesh nodes are  kept in separate  enclo-sures, they can be independently positioned for optimum RF connectiv-ity. For example, in a multi-building mesh network, mesh nodes should be placed in areas that enable the best connectivity between buildings, while the APs can be mounted for best interior coverage. A HotPoint access point can share a Firetide mesh node with other devices for true triple-play networking at any mesh node location. This  can in-clude a second HotPoint access point operating on a different channel, a video camera, a VoIP device, or even a third party access point.      All HotPoint access points, as well as all Firetide mesh nodes, can be man-aged across the network from a central location regardless of whether the access points are connected to wireless mesh nodes, to a wired infrastruc-ture, or both. This integrated approach also allows network broadcasts to all access clients anywhere on the network.  •••••
2  Wireless Access Point User Guide Management & Configuration features include:SNMP v2/3FTP firmware upgradeVirtual AP Grouping- uniform SLAsPhysical AP Grouping – uniform parametersPer-user and per-VAP data rate limitingPer-user based accountingHotPoint + HotPort Network ApplicationsWi-Fi NetworksTogether, HotPoints and HotPorts allow you to quickly deploy Wi-Fi service anywhere. The Firetide mesh provides more flexibility for Wi-Fi deployment than other mesh solutions because it can support existing third-party APs as well as Firetide HotPoint APs. Each HotPort can support up to four APs, so  high-density  Wi-Fi  can  be  deployed  at  a  lower  cost  than  using  mesh nodes that are limited to a single access point.Voice over IPThe HotPort mesh network enables clear VoIP traffic over the wireless back-bone. Both wired and wireless VoIP phones support Class-of-Service priori-tization which enables you to assign high priority to voice traffic to ensure the best quality voice transmission.VideoThe high capacity and sustained throughput of the HotPort network makes it  ideal  for  IP  video  networks  and  video  surveillance  applications,  espe-cially those requiring multiple cameras or faster frame rates. Wi-Fi cameras are not needed because any camera with an Ethernet interface can connect directly to a HotPort  mesh node. HotPort  outdoor mesh  nodes also sup-port Power over Ethernet, allowing the use of a single power connection to power both the node and the camera.•••••••HotPoint Access Point FeaturesWireless features include:Frequency ranges 2.400—2.484 GHzTransmit up to 400 mW with 802.11h Automatic XMIT Power ControlManual Transmit Power Control with 802.11d Auto Channel SelectNetwork features include:Up to 16 independent VLANsUp to 16 ESSIDs per HotPointUp to 64 clients per HotPointWDSDHCP client and server, separate DHCP range per SSIDNAT802.1p (Quality of Service)802.11e (WMM) (Quality of Service)Inter Access Point Protocol (IAPP) enabled per 802.11fFast handoff enabled per draft of 802.11rIntercell blocking – blocks communication between APsIntracell blocking – blocks communication between BSSIDsSecurity and Encryption features include:802.11i with 40 bit or 104 bit WEP keys; 128 bit or 256 bit AES keys, TKIP802.1x authenticationWPA2VPN tunneling and filteringESSID suppressionFirewallMAC access controlRogue AP detection••••••••••••••••••••••••••
  HotPoint Wireless Access Point  3 DataThe HotPort mesh network also provides direct connectivity for computers and servers via a cable to the Ethernet ports on each node. Point-of-SaleHotPoint APs and the HotPort network make it easy to deploy Point-of-Sale terminal support at trade shows, fairs, and other temporary locations, as well as to support handheld wireless  devices  in inventory,  tracking,  and other logistics applications.PrintingWith the HotPort mesh network network printers become wireless printers, without additional setup, drivers, or software, simply by connecting to one of the Ethernet ports on a HotPort mesh node. This wireless capability al-lows network printers to operate anywhere, including mobile carts and in temporary settings.HotPoint + HotPort FeaturesSecurityHotPort  mesh  networks  feature  multiple  layers  of security,  including  40 and 104 bit WEP key and 128 and 256 AES key encryption. The mesh also provides packet filtering, based on MAC addresses, to limit access to  the mesh. For additional security, a proprietary mesh protocol prevents non-HotPort devices from participating on the mesh. VLANs The HotPort mesh network includes support for virtual local area networks (VLANs) to enable traffic to be  separated  into  smaller groups  and appli-cation-specific LANs. The HotPort mesh supports 802.1q VLAN tagging of packets entering and exiting the mesh. You can assign Ethernet ports to different VLANs; only ports belonging to the same VLAN can switch traffic among themselves. You can define up to 4093 VLAN IDs and create up to 16 multiple, logically separated VLANs within a single mesh. The HotPort mesh also supports VLAN trunks.Traffic Prioritization (class of service)The HotPort system provides traffic prioritization levels to prioritize traf-fic on the  mesh. This helps  ensure that  certain types of  traffic  requiring high throughput or continuous service, such as voice, take precedence over other forms of traffic. Intuitive Network Mesh Management with HotView™ SoftwareHotView™ mesh management software provides live monitoring and man-agement of Firetide HotPort wireless mesh networks, including HotPoint AP nodes. The  software features a  graphical  user  interface  and provides access to all mesh and node settings, including security, VLAN, class of ser-vice, radio power controls, and network gateway interconnects. Live moni-toring features include mesh and node statistics. HotView Pro extend the management features of HotView across multiple meshes. Thus, an enterprise can manage all of its HotPort meshes world-wide from anywhere.HotView  and HotView Pro operate on virtually  any workstation  or server that is connected  to the mesh, either directly or remotely via WAN connec-tion or the Internet.Radio SettingsHotPort wireless mesh supports 2.4 GHz OFDM and DSSS radio modes, as well as 5 GHz OFDM. When combined with 802.11b/g APs, the backbone can be run at 5 GHz, thus avoiding interference.
4  Wireless Access Point User Guide Table 1. Summary of Firetide Mesh Router ModelsModel & SKU Use Band RF Output Power TCP Data Rate Default Channel3101 Indoor 2.4, 5 GHz standard 10 Mbps 2.462 GHz DSSS, Ch 113103 Indoor 2.4, 5 GHz standard 25 Mbps 2.462 GHz DSSS, Ch 113100/PS Indoor, Public Safety 2.4, 4.9, 5 GHz standard 25 Mbps 4.962 GHz DSSS, Ch 53500-2401 Indoor 2.4 GHz high 10 Mbps 2.462 GHz DSSS, Ch 113500-5001 Indoor 5 GHz high 10 Mbps 5.805 GHz OFDM, Ch 1613500-2403 Indoor 2.4 GHz high 25 Mbps 2.462 GHz DSSS, Ch 113500-5003 Indoor 5 GHz high 25 Mbps 5.805 GHz OFDM, Ch 1613203 Outdoor 2.4, 5 GHz standard 25 Mbps 2.462 GHz DSSS, Ch 113200PS Outdoor, Public Safety 2.4, 4.9, 5 GHz standard 25 Mbps 2.462 GHz DSSS, Ch 113600-2400 Outdoor 2.4 GHz high 25 Mbps 2.462 GHz DSSS, Ch 113600-5000 Outdoor 5 GHz high 25 Mbps 5.805 GHz OFDM, Ch 161HotPort 3100 and 3500 Series Mesh RoutersHotPort 3100 series mesh nodes provide fast and easy indoor network de-ployment.  They  connect  wirelessly  to  other  indoor  and  outdoor  HotPort nodes to form a mesh network. Ethernet packets are automatically switched across the mesh, in a manner analogous to an Ethernet switch, using Auto-Mesh™, a proprietary protocol developed by Firetide. AutoMesh has been optimized for efficiency in wireless mesh environments. HotPort nodes are plenum-rated and feature a built-in four-port 10/100 Ethernet switch for connecting networking devices a fully wireless mesh backbone. Models are available for operation at 2.4 GHz for high capacity and maximum range or at 5 GHz for high capacity and minimal interference from 2.4 GHz devices.The HotPort 3100/PS supports the public safety band, used in the US.The HotPort 3500 Series feature band-specific high-power radios, but are otherwise identical to the 3100 Series Models.Outdoor NodesIn addition  to the indoor  models, Firetide  offers a range  of HotPorts for outdoor use. These are similar to the 3100 and 3500 Series units, but are packaged in NEMA-4 enclosures suitable for outdoor use.The full model  range  is shown in  this table:  (Data  rates are typical  for a single hop operation.)
  HotPoint Wireless Access Point  5 Indoor Unit - Unpacking and InstallationUnpacking and setup are straightforward. The HotPoint 4500 requires AC power, but can be mounted almost anywhere indoors. Brackets are avail-able to facilitate wall or ceiling mounting. You will need a cat-5 cable to connect the AP to its companion Firetide mesh node. This cable can be any length permissible for 10/100 Mbps Ethernet.Your AP includes a power supply and three different AC line cords, as shown in Figure 1. Use the one appropriate for your region.Figure 1. Indoor AP Power SupplyAuxiliary Bracket Main MountingBracketHotPoint APFigure 2. Optional Mounting BracketsWall/Ceiling Mounting Bracket (optional) with Auxiliary bracket for cube-wall applications.Bracket Lock Mechanism DetailFigure 3. Firetide HotPoint 4500 Series - Front View Figure 4. Firetide HotPoint 4500 Series - Rear View Mount your HotPoint in a location that will give the best wireless coverage of AP clients. The access point does NOT have to be close to its companion HotPort node; in fact, it is better to mount each unit in a location that is optimum for the RF needs of that unit.After the units are  installed,  connect  the  access point to its  companion HotPort node with a cat-5 cable. Then apply power to the access point.
6  Wireless Access Point User Guide Outdoor Unit - Unpacking and InstallationUnpacking  and  setup  are  straightforward.  Included  with  your  HotPoint 4600 are:Mounting bracket and hardware2.4 GHz omnidirectional antennas (2)Weatherproof Ethernet cable, 10-pin to 10-pin, PoE-compatible. This ca-ble will power your HotPoint when connected to port 2 of a Firetide 3200 Series or 3600 Series outdoor node.You may wish to configure your HotPoint 4600 before installation. Refer to the software section of this manual for details on initial setup.Note: a Firetide outdoormesh node  can support up to two access points, but it can only power 1 unit via PoE. In addition, there are constraints on overall bandwidth and on VLAN support. In most cases, you will want to use only one HotPoint per HotPort.Pole InstallationInstallation on any pole up to 2 inches is easy. Begin by mounting the sup-plied U-bolts,  and ‘claw’ pieces to the pole, using two nuts, as shown in Figure 5. Make the nuts just finger-tight. Depending on the pole diameter, you may need additional nuts, as shown on the lower clamp of Figure 5. The purpose of the extra spacer nuts is to prevent the U-bolt legs from protruding too far out beyond the mounting plate. This will interfere with the AP. If required, place two more spacer nuts on the U-bolts. •••Figure 5. Pole Clamps
  HotPoint Wireless Access Point  7 Next, attach the plate, using two more nuts, as shown in Figure 6. Adjust the spacer nuts to insure that the U-bolts do not protrude out of the fold in the plate. The exact adjustment will depend on pole diameter.Figure 6. Mounting PlateWhen the plate is mounted and aligned, tighten all the nuts with a 7/16-inch wrench. Then slide the HotPoint onto and downward slightly, so that its tabs on its backing plate (Figure 7) engage the mounting plate, as shown in Figure 8. Tighten the four knurled nuts on the sides.The supplied antennas can be used for initial  deployment, but should be replaced after initial testing with outdoor-rated units of suitable gain and pattern.Figure 7. AP Bracket Mounting TabsFigure 8. AP Mount - Finished
8  Wireless Access Point User Guide Understanding APs, AP Groups, VAPs, & VAP GroupsBefore you begin installation, you should understand how Firetide’s Hot-View Network Management System views HotPoint Access Points. An AP is a physical box - a computer and a radio -  which can implement up to 16 “virtual” access points. Virtual access points are the things that wire-less clients actually see and connect to. Each HotPoint node offers a range of network as well as radio configura-tion options. The commands which control these features and options are grouped logically. This makes it easy to manage large collections of physi-cal nodes and virtual APs, once you understand the concepts.Access Points (AP) - certain parameters, such as radio settings, are specific to the hardware on each particular physical node.Virtual Access Points (VAP) - HotPoint nodes support Virtual Access Points. In general, each physical HotPoint can support up to 16 VAPs. (A HotPoint which is the server node of a WDS cluster can only belong to one VAP.)VAP Groups -  VAPs are grouped together for management  purposes.  You will create at least one VAP group, with SSID, encryption, and other param-eters. This is the ‘access point’ that will appear to wireless clients.Access Point Groups - In some cases, you may want to grant management access to some nodes to one person or persons, and other nodes to other persons. This can be done using Access Point Groups. Each HotPoint may be assigned to an Access Point Group, or AP group. You can specify different user names and passwords for each group.All HotPoint commands are grouped according to whether they affect set-tings on a physical node, a VAP Group, an AP Group, or an individual VAP.NameIP AddressFirewallVPNNameIP AddressFirewallVPNNameIP AddressFirewallVPNVAP GroupsVAP Group A VAP IP AddressDHCP / DNSNATVAP IP AddressDHCP / DNSNATVAP IP AddressDHCP / DNSNATSSIDEncryptionMAC Address AccessAP GroupLoginPasswordAP APAPVAP VAPVAPNameIP AddressFirewallVPNVAP GroupsVAP Group A VAP IP AddressDHCP / DNSNATSSIDEncryptionMAC Address AccessAP GroupLoginPasswordAPVAPFigure 9 shows how the various domains relate to each other.Figure 9. Matrix of Physical and Logical APs - SimpleFigures 10 and 11 show more complex arrangements of multiple APs and multiple Virtual APs.Figure 10. Three-AP Network
  HotPoint Wireless Access Point  9 NameIP AddressFirewallVPNNameIP AddressFirewallVPNNameIP AddressFirewallVPNVAP GroupsVAP Group AVAP Group BVAP IP AddressDHCP / DNSNATVAP IP AddressDHCP / DNSNATVAP IP AddressDHCP / DNSNATVAP IP AddressDHCP / DNSNATVAP IP AddressDHCP / DNSNATVAP IP AddressDHCP / DNSNATSSIDEncryptionMAC Address AccessSSIDEncryptionMAC Address AccessVAP Group C VAP IP AddressDHCP / DNSNATVAP IP AddressDHCP / DNSNATVAP IP AddressDHCP / DNSNATSSIDEncryptionMAC Address AccessAP GroupLoginPasswordAP APAPVAP Group D VAP IP AddressDHCP / DNSNATVAP IP AddressDHCP / DNSNATVAP IP AddressDHCP / DNSNATSSIDEncryptionMAC Address AccessVAP VAPVAPVAP VAPVAPVAP VAPVAPVAP VAPVAPFigure 11 shows a three-AP, three-VAP configuration. You can have up to 16 VAPs per physical AP. You can have as many AP Groups as needed, and there is no limit to the number of APs in any one AP Group.Figure 11. Large AP MatrixTable 2 gives a summary of all of the major commands and options avail-able on the HotPoint APs, organized by logical group.Table 2. Summary of Commands by Logical GroupPhysical AP AP Group VAP ConfigurationVAP Group ConfigurationAP Name Membership DHCP ServerDHCP Service IP addressWDS (new group creation only)AP Mgmt IP address/ DHCP clientGuest LoginAdmin LoginDNS Broadcast SSIDSSID suppressionPerformance Statistics NAT VLANRadio Settings: ch, mode, RF power, bea-con, rogue detectionDTIM, RTS/CTS, fragmentationFirewall EncryptionVPN MAC address accessCountry Code Intracell blockingReboot / Reset User data rate controlImport & Apply IAPPRefresh WMM
10  Wireless Access Point User Guide IP Address PlanningYou should plan out your IP addressing scheme prior to deployment. You will need several ranges of IP addresses. All of these IP addresses are in addition to the management IP address (aka mesh IP address) assigned to your Firetide mesh network.In general, you may  assign AP IP  addresses  independently of the IP ad-dressing scheme you use for the Firetide mesh. The only constraint on AP IP address assignment is that the IP addresses must be routable within your overall IP addressing scheme.AP Management IP Address - this is the IP address assigned to the physi-cal access point, and is used for management purposes. An AP is capable of acquiring this address from a DHCP server, or it may be manually as-signed. This address must be reachable from the HotView management workstation.VAP Management / DHCP Server IP Address - Each VAP requires an IP address. It is used for NAT, if enabled, and for DHCP, if the AP is configured to assign IP addresses to clients. It must be different from the AP Manage-ment IP address. Note that each AP can be a member of as many as 16 VAP Groups.DHCP Address Range - this is the pool of addresses available to be as-signed to wireless clients.It is permissible for an AP to acquire its AP Management address via DHCP, yet also serve DHCP addresses to clients. The addresses do not need to be on the same subnet, but all must be routable over the enterprise LAN.•••Software InstallationIf you are  installing  a new Firetide-based  wireless network, begin by  in-stalling  the  HotPort  Mesh  nodes, and the HotView or HotView Pro mesh management  software,  before  installing  any  HotPoint  APs.  Refer  to  the documentation supplied with those products for details. If you are adding HotPoint APs to an existing network, begin by upgrading the existing mesh nodes to version 3.4.X.X or later. Use your existing ver-sion of HotView to  upgrade all mesh nodes, then use HotView 3.4.X.X to configure HotPoint APs.Basic Setup SequenceSeveral  steps  are involved  in  configuring  a  HotPoint AP.  These  steps  are summarized here, then shown in detail in the following pages.Assign a management  IP address to each AP. This address should be reach-able from the computer running HotView. It does not need to be on the same subnet as the management address of the Firetide mesh.Log in to the AP.Set the Country Code.Rename the AP. A name based on the AP’s location is a good choice.Set the radio settings (channel, etc) for each physical AP.Repeat these steps for all access points. Then:Create one or more VAP Groups, using the VAP Group Configuration com-mand. You must have at least one group, even if you only have one AP.Use  the  VAP  Configuration  command  to  configure  those  VAP  features which are controlled per physical AP. (DHCP, DNS, NAT)Use the VAP Group configuration command to assign the SSID, security, and other features for the entire VAP group.Use the AP Group command to group all of APs into a managment group. (This is not necessary if you only have one AP. Also, you can create more than one group if you require multiple management domains, but it most cases this is not required.)1.2.3.4.5.1.2.3.4.
  HotPoint Wireless Access Point  11 Software ConfigurationThe Firetide HotPoint access point family requires HotView or HotView Pro software,  version  3.4.X.X  or  newer,  on  your  computer.  In  addition,  the Firetide HotPort nodes to which the access points will be connected must be upgraded to firmware version M3.4.X.X. Access Points should have firm-ware version A3.4.X.X installed. After you’ve physically installed your ac-cess point, launch HotView (or HotView Pro). You will see a screen similar to this one:
12  Wireless Access Point User Guide AP Node CommandsThese commands are accessed by right-clicking the AP icon. Begin by as-signing an IP address to each node, and logging in to the node. You must then set the Country Code. Finally, you should rename each node.Command FunctionRename AP Assigns the management screen name to the physical node. Note: this is NOT the SSID of the node; that is specified under the VAP Group Configuration command.IP Settings (includesManagement VLAN)Assigns the IP address that will be used by the AP for management access. This command also allows you to assign a management VLAN, if desired.Release Lock Releases management control lock on APs.Login The default user ID and password is admin and firetide.Statistics Shows performance for a given VAP.AP Configuration(Radio)Allows you to specify the radio parameters, firewall configuration, and VPN. VAP Configuration Allows you to define DHCP service for the VAP.VAP Group  ConfigurationAllows you to define radio and security options for a group of  Virtual Access Points.Country Code Set once at initial startup.Reboot, Reset Allows you to reboot or reset to factory defaults.Import, Apply Allows you to save and restore node settings.Refresh Forces HotView to re-acquire the status of the AP.Delete HotPoint Removes ‘stale’ HotPoint icons from HotView.Summary Gives a summary of HotPoint node information.
  HotPoint Wireless Access Point  13 Physical AP Radio SettingsEach physical AP has certain radio settings which are common to all virtual APs on that node. These are set using the AP Configuration command, as shown at right.Auto Channel allows the AP to find the clearest channel, or you may set the channel manually.The Wireless Mode can be set to b, b/g, g-only, or 108g Static Turbo.The raw Transmit Data Rate of the wireless link can also be specified.Transmitter power and beacon can be controlled.Antenna Diversity is supported. This control determines which antenna the unit listens on; transmit is always on Antenna 1. In most cases, Diversity is the best choice, but if you are only installing one antenna, set this to  Antenna 1.Rogue AP Detection enables the AP to detect other, “unknown” APs oper-ating in the area, and report them. You may specifiy how often the AP stops and scans for rogue APs, as well as the level of search.
14  Wireless Access Point User Guide VAP Group ConfigurationVAP Groups are the collections of Virtual Access Points that form the user-visible ‘logical layer’ overlaid on the physical collection of Access Points.You must create at least one VAP Group, with at least one VAP in it. Do this by  selecting  VAP  Group  Configuration  command  from  the  Access  Point menu. You will see the Manage VAP Groups screen, as shown on the left.  Click on the New VAP Group button. The New VAP Group screen appears, as shown on the right. Enter a VAP Group Name. This is NOT the same as the SSID. Select one (or more) APs which will support this VAP group. Note that APs can be members of more than one VAP group. Typically, all APs are members of all VAP Groups.You can also create Wireless Distribution Service (WDS) networks. However, there are some limitations:APs which are members of a WDS-enabled VAP Group cannot be members of any other VAP Group.Do not use WDS to bridge two APs which are connected to the same Firetide mesh. This creates a routing loop. Set the SSID and radio data rates.There  are  two  remaining  basic  setup  steps:  VAP  Configuration  and  VAP Group Configuration. The order in which you do these is not critical; this manual will configure each VAP next.••
  HotPoint Wireless Access Point  15 VAP SettingsAs shown in Figure 11, VAP Groups logically intersect with APs to form VAPs. Certain settings are specific to each VAP. These settings include the IP ad-dress of the VAP, the DHCP Server settings, the DNS settings, and the op-tional NAT capability.To modify these settings, right-click on the AP icon and select the VAP Con-figuration command. This command will reveal a second drop-down menu which lists all of the available VAPs. Select the VAP you wish to configure. You will see a screen like the one at right. Enter the VAP IP address. This must NOT be the same as the management IP address of the AP. If desired, configure DHCP service. For DHCP, each VAP Group should have every node in that group configured to serve addresses to clients. All nodes must be configured, and each node must have a unique range of assignable IP addresses.Note: it is possible, using VLANs, to insure that each client receives its IP address from the VAP with which it physically associates, rather than the first DHCP server within the VAP Group to respond. This is useful in multi-tenant applications. Each node will need a VLAN; refer to your HotView Pro manual for assistance in VLAN configuration.You may also use an independent DHCP server. The HotPoint AP will forward DHCP requests if it is not configured to serve DHCP addresses.NAT may be enabled here, if desired.
16  Wireless Access Point User Guide VAP Group SettingsBasic VAP Group SettingsThe SSID defaults to the VAP Group name, but this can be changed if de-sired. You must also enable the VAP Group by checking the box.DTIM is the Delivery Traffic Indication Message.  It indicates which client stations, currently sleeping in low-power mode, have data buffered on the access point awaiting pick-up.The DTIM period you specify here indicates how often the clients served by this access point should check for buffered data  still on the AP awaiting pickup.Fragmentation and RTS/CTS Thresholds can be used to tune wireless per-formance in some specialized applications.A VLAN can be created for this VAP Group. This can be useful for security and privacy purposes.
  HotPoint Wireless Access Point  17 VAP Group Security SettingsA wide range of wireless security options are supported. Select the one you prefer. Authentication choices include:802.1XAutoOpenShared KeyWPAWPA-AutoWPA-Auto-PSKWPA-PSKWPA2WPA2-PSK••••••••••
18  Wireless Access Point User Guide MAC Address Access ControlIf desired, VAP Group access can be limited to an explicit group of MAC ad-dresses, or denied.
  HotPoint Wireless Access Point  19 AP Group CommandsHotPoint  Access  Points  can  be  grouped  for  management  purposes.  Each group shares a set of administrative accounts and passwords. The AP Group Configuration command, under the Access Point menu, opens a dialog box, in which you can create new groups and edit existing groups. The Configure button  lets you re-define  the  user ID  and password for  all APs in a group. There is an account name for read-write privileges, and a second, ‘guest’ account with read-only privileges. The defaults are admin and firetide, but these should be changed for security reasons.Most  small  installations  will find a  single AP group  for  all APs to be the most convenient to manage. Larger installations which have APs for secu-rity purposes as well as user data networking may wish to divide the man-agement functions (and access privileges) by creating multiple groups with unique user IDs.
20  Wireless Access Point User Guide Understand Advanced SettingsIntracell BlockingIntracell blocking allows you to prevent users of a given VAP from seeing each other. When enabled, all users can use the AP to reach the network, but no user can access other computers on that VAP.Note Intercell blocking is accomplished with VLANs.User Data RateIn  order  to  prevent  one  user  from  consuming  excess  bandwidth  on  the backbone, you can limit the data rate for each user. You can also limit the aggregate rate for each VAP Group.IAPP and RoamingThe  Inter-Access  Point  Protocol  describes  an  optional  extension  to  IEEE 802.11 that provides wireless access-point communications among multi-vendor systems. If you have other APs which support it, you can enable its operation and set the port used for control.WMMWMM, also known as WME, allows clients which support the Wireless Mul-timedia Extensions protocol to prioritize VoIP and video traffic. If your cli-ents support it, enable it here.
  HotPoint Wireless Access Point  21 Advanced FeaturesFiretide HotPoint APs support several advanced features. These include:NATFirewallVPNNATNetwork Address Translation is configured per VAP; that is, each physical node has a NAT setting for each VAP Group to which it belongs. Use the VAP Configuration command (in the right-click menu) to configure it.FirewallThe Firewall  features is configured per physical AP, and  is common to all VAP Groups on that AP. The Firewall blocks ports coming from the AP’s wired connection, going to the wireless clients.By default, all ports are  open. Enabling  the  Firewall  closes all ports; in-dividual ports can then be  opened as needed. Use the AP Configuration command (in the right-click menu) to configure it.VPNAPs can be tunneled directly to a remote network by using the VPN feature. The VPN will tunnel all traffic from a physical AP, regardless of VAP Group. Use the AP Configuration command (in the right-click menu) to configure it.•••Country Code AssignmentFiretide  HotPoint  APs  are  designed  to  be  compliant  with  all  applicable regulations for their country of operation. In order for this to work, the AP needs to know which country it is in. You MUST set the Country code in order for the HotPoint AP to work cor-rectly.  If  the  Country  Code  has  not  been set, you may see  the  following warning:
22  Wireless Access Point User Guide WirelessIEEE 802.11b/gFrequency ranges 2.400—2.484 GHzTransmit power up to 400 mW802.11h (Automatic Transmit Power Control)Manual Transmit Power Control802.11d (Auto Channel Select)Receive sensitivity measured at N connector:2.4 GHz, DSSS1 Mbps: -96 dBm11 Mbps: -90 dBm2.4 GHz, OFDM6 Mbps: -93 dBm54 Mbps: -74 dBmMedia Access Protocol: CSMA/CA with ACKModulation techniques: DSSS, OFDM, CCK, DQPSK, DBPSKRange up to 200 meters depending on clientWDSNetworkingUp to 16 independent VLANsDHCP client and server, separate DHCP range per SSIDUp to 16 ESSIDs per HotPoint••••••••••••••••••••Security and Encryption802.11i40 bit, 104 bit WEP keys128 bit, 256 bit AES keys802.1x authenticationTKIPWPA2VPN tunneling and filteringESSID suppressionFirewallMAC access controlRogue AP detectionManagement & ConfigurationIntegrated mesh and access managementWeb-based managementSNMP v2/3CLIFTP firmware upgrade802.1p (Quality of Service)802.11e (WMM) (Quality of Service)NATVirtual AP Grouping – uniform SLAsPhysical AP Grouping – uniform parametersPer-user and per-VAP rate limitingPer-user-based accounting•••••••••••••••••••••••Appendix A - HotPoint Features and Specifications
  HotPoint Wireless Access Point  23 PerformanceUp to 54 MbpsUp to 64 concurrent users simultaneously per HotPointInter Access Point Protocol (IAPP) enabled per 802.11fFast handoff enabled, per 802.11r draft recommendationIntercell blocking – blocks communication between APsIntracell blocking – blocks communication between BSSIDsAuto discoveryConfigurable web portalBroadcasted advertisingNo user configurationNetwork PortOne 10/100 Base-T (RJ-45) ports IEEE 802.3, 802.3u compliantCSMA/CD 10/100 auto-senseIndoor Unit - PowerInput voltage: 5 VDC @ 2.0 AExternal power supply: 100-240 VAC, 50/60 HzPower consumption: 10 WOutdoor Unit - PowerInput voltage requirement: 5 VDC @ 2.0 APoE-compatible - will operate PoE supplied by Firetide 3200/3600 Series Outdoor Mesh RouterOptional external power supply: 100-240 VAC, 50/60 HzPower consumption: 10 W •••••••••••••••••••Indoor Unit EnclosureSystem indicator LEDs (power, status, mesh, fault)Ethernet indicator LEDs (link status, activity)Two antenna connectors: SMA, reverse polarityPower connectorOne Ethernet data connectors (RJ-45)Reset button (recessed)Security slot for physical locking deviceWeight: 2.1 lbs (.95 Kg) without external transformerDimensions: 9.00 in x 5.84 in x 1.07 in (22.85 cm x 14.83 cm x 2.71 cm)Outdoor Unit EnclosureNEMA-rated die-cast aluminumTwo antenna connectors, type NWeatherproof power connectorWeatherproof Ethernet connectorRegulatory agency certificationsPlenum rated UL2043FCC Part 15Environmental specificationsOperating temperature: -20º C to +60ºCStorage temperature: -20º C to +70º CHumidity (non-condensing): 10% to 90%Storage humidity (non-condensing): 10% to 90%•••••••••••••••••••
24  Wireless Access Point User Guide Appendix B - Regulatory NoticesUSAFCC Class A NoticeThis device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:This device may not cause harmful interference.This device must accept any interference received, including interference that may cause undesired operation.FCC Part 15 NoteThis equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in an office installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the in-structions, may cause harmful interference to radio communications. How-ever, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:Reorient or relocate the receiving antenna.Increase the separation between the equipment and receiver.Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.Consult  the  dealer  or  an  experienced  radio/television  technician  for help.••••••ModificationsAny modifications made to this device that are not approved by Firetide, Inc. may void the authority granted to the user by the FCC to operate this equip-ment.FCC Radiation Exposure StatementThe antenna used for this transmitter must be installed to provide a separa-tion distance of at least 35 cm from all persons and must not be co-located or operated in conjunction with any other antenna or transmitter. OEM Inte-grators, end-users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance.InstallationAntenna(s) for this unit must be installed by a qualified professional. Opera-tion of the unit with non-approved antennas is a violation of U. S. FCC Rules, Part 15.203(c), Code of Federal Regulations, Title 47.Approved antennas are:Maxrad / PCTel  MFB24008NCG Coment  SF-245WFiretide   C812-510010-A
  HotPoint Wireless Access Point  25 Canadian Compliance StatementThis Class B Digital apparatus meets all the requirements of the Canadian Interference-Causing  Equipment Regulations.  Cet  appareil numerique de la classe B respecte les exigences du Reglement sur le material broilleur du Canada. This device complies with Class B Limits of Industry Canada. Opera-tion is subject to the following two conditions:1. This device may not cause harmful interference, and2. This device must accept any interference received,  including interfer-ence that may cause undesired operation.Firetide HotPoint 4500 and 4600 wireless access points are certified to the requirements of RSS-210 for 2.4-GHz spread spectrum devices.  The use of this device in a system operating either partially or completely outdoors may require the user  to obtain a license for the system according to the Canadian regulations. For further information, contact your local Industry Canada office.•
www.firetide.com © 2005, 2006 Firetide, Inc. All rights reserved APUG001 082206HotPoint Wireless Access Point

Navigation menu