Firetide 3600-2 HotPort 3600-5000 User Manual SR 5 Users Manual

Firetide Inc. HotPort 3600-5000 SR 5 Users Manual

Contents

SR 5 Users Manual

SR5 MANUALThe SR5 hi-power mini-PCI 802.11a radio card module has been specifically designed for use in outdoor wireless applications where additional link gain is critical. It is compatible with existing Atheros linux drivers and is capable of operation in the 5725-5850 MHz frequency range. Power and frequency limits are hard programmed into the radio card EEPROM, but card compatibility can be achieved with any Atheros Linux based software. Many SBC host platforms have been qualified for use with the SR5 module including:-Mikrotik Router Boards-PC Engines WRAP boards-Many SBC platforms from large telecommunication companiesIt is necessary that the system integrators perform all applicable retesting and certification for their final system configurations.EXAMPLE OEM SYSTEM USAGEMODULAR USAGEPC ENGINES WRAP Wireless Router BoardATHEROS PUBLIC MADWIFI DriverUbiquiti Networks, Inc.778 N. First St.San Jose, CA 95112(408)-385-1103SR5Pac Wireless Roo TennaAntenna/EnclosureSoftware Driver
SR5 IMPORTANT MODULAR APPROVAL INFORMATION This device is intended only form OEM integrator under the following conditions: 1) The antenna must be installed such that 20cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. IMPORTANT NOTE: In the event that these conditions cannot be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. End Product Labeling This transmitter module is authorized only for use in devices where the antenna may be installed such that 20 cm may be maintained between the antenna and users (for example access points, routers, wireless ADSL modems, and similar equipment). The final end product must be labeled in visible area with the following: “Contains TX FCC ID SWX-SR5: End Product Manual Information The user manual for end users must include the following information in a prominent location “IMPORTANT NOTE: To comply with FCC RF exposure compliance requirements, the antenna used for this transmitter must be installed to provide a separation distance of at least 20cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.”
SR5 IMPORTANT OPERATION INFORMATIONSafety Information20 cm

SR5 Users Manual

SR5 MANUALThe SR5 hi-power mini-PCI 802.11a radio card module has been specifically designed for use in outdoor wireless applications where additional link gain is critical. It is compatible with existing Atheros linux drivers and is capable of operation in the 5725-5850 MHz frequency range. Power and frequency limits are hard programmed into the radio card EEPROM, but card compatibility can be achieved with any Atheros Linux based software. Many SBC host platforms have been qualified for use with the SR5 module including:-Mikrotik Router Boards-PC Engines WRAP boards-Many SBC platforms from large telecommunication companiesIt is necessary that the system integrators perform all applicable retesting and certification for their final system configurations.EXAMPLE OEM SYSTEM USAGEMODULAR USAGEPC ENGINES WRAP Wireless Router BoardATHEROS PUBLIC MADWIFI DriverUbiquiti Networks, Inc.778 N. First St.San Jose, CA 95112(408)-385-1103SR5Pac Wireless Roo TennaAntenna/EnclosureSoftware Driver
SR5 IMPORTANT MODULAR APPROVAL INFORMATION This device is intended only form OEM integrator under the following conditions: 1) The antenna must be installed such that 20cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. IMPORTANT NOTE: In the event that these conditions cannot be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. End Product Labeling This transmitter module is authorized only for use in devices where the antenna may be installed such that 20 cm may be maintained between the antenna and users (for example access points, routers, wireless ADSL modems, and similar equipment). The final end product must be labeled in visible area with the following: “Contains TX FCC ID SWX-SR5: End Product Manual Information The user manual for end users must include the following information in a prominent location “IMPORTANT NOTE: To comply with FCC RF exposure compliance requirements, the antenna used for this transmitter must be installed to provide a separation distance of at least 20cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.”
SR5 IMPORTANT OPERATION INFORMATIONSafety Information20 cm

Navigation menu