Firetide 3600-1 HotPort 3600-2400 User Manual

Firetide Inc. HotPort 3600-2400 Users Manual

UserManual.wiki >

3600-1 User Manual >

Contents

1. Users Manual
2. Ubiquiti Users Manual

Users Manual

HotPortTM User GuideHotPort 3200 & 3600 Series Outdoor Wireless Mesh Nodes

Firetide Instant Mesh Networks iiiHotPort Limited End User Product WarrantyPursuant to all provisions described herein, Firetide products are warranted for one (1) year from the date of purchase against de-fects in the build materials and workmanship. Firetide also war-rants that the Software will materially conform to the documen-tation supplied by Firetide with the Software. In the event that the Software fails to materially conform to the documentation and an authorized Firetide reseller is notiﬁed in writing of such failure within the warranty period, Firetide or its reseller shall use commercially reasonable efforts to promptly correct the noncon-formity. Firetide does not warrant that the use of the Software will be uninterrupted or error free. Firetide does not warrant that the Products will meet any requirements or speciﬁcations of any End User Customer. This warranty applies to the entire Firetide product, including antennas and the AC power adapter.The above warranties are void if the alleged defect cannot be veriﬁed by Firetide or if, as determined by Firetide, the product failure was due to tampering, abuse, misuse, accident, shipping, handling, or storage; or if the product has been installed, used, or maintained in a manner not described in the product user manual, if the product has been altered In any way, or If product serialization has been altered. Any attempt to disassemble or re-pair the product by anyone other than Firetide immediately voids this warranty.This warranty applies only to the original End User purchaser of the product and may not be transferred to any other individual or entity.THE FOREGOING ARE THE EXCLUSIVE WARRANTIES APPLICABLE TO THE PRODUCT INCLUDING THE SOFTWARE, AND THE EXCLUSIVE REMEDY FOR DEFECTS IN THE PRODUCT. FIRETIDE DISCLAIMS ALL OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED, STATUTORY OR OTHERWISE, INCLUDING BUT NOT LIMITED TO IMPLIED WARRAN-TIES OF MERCHANTABILITY, NON-INFRINGEMENT OR FITNESS FOR A PARTICULAR PURPOSE. SOME LAWS DO NOT ALLOW THE EXCLU-SION OF IMPLIED WARRANTIES SO TO THAT EXTENT THIS LIMITA-TION MAY NOT APPLY TO YOU.In no event will Firetide be liable for any special, inciden-tal, consequential, punitive or indirect damages whatsoever (including, without limitation, damages for loss of proﬁts, business interruption, loss of information, or other pecuniary loss) arising out of the use or inability to use the product or the performance, interruption or failure of the product, irrespec-tive of the cause of action, even if Firetide has been advised of the possibility of such damages. Firetide’s cumulative liability for all claims arising out of or in connection with this warranty will not exceed the amount paid by the original End User purchas-er to purchase the product. The amounts payable for the product are based in part on these limitations and these limitations shall apply not-withstanding the failure of essential purpose of any remedy. Some jurisdictions do not allow the exclusion or limita-tion of incidental or consequential damages, so to that extent the above limitations or exclusions may not apply to you.By using the product the original End User purchaser agrees to and is bound by these terms and conditions.In the event that a product fails to meet this warranty and Firetide’s authorized reseller is notiﬁed in writing of such failure within the warranty period, Firetide shall, at its own dis-cretion, either repair the product or replace it with the same or a functionally-equivalent product free of charge. Replace-ment products may contain refurbished materials in whole or in part. Firetide will honor this warranty provided the prod-uct is returned through an authorized Firetide reseller or dealer with shipping charges prepaid, along with a proof of purchase describing the original purchase date and product serial numbers if applicable. The authorized reseller must acquire a Return Materials Authorization (RMA) number from Firetide prior to returning any product. Firetide does not accept ship-ments of defective products without shipping charges prepaid.

iv HotPort 3200 Series User GuideExplanation of Graphical SymbolsThis symbol is intended to alert the user to the pres-ence of important operating, maintenance, and ser-vicing instructions in the literature accompanying this unit. Failing to comply with this instruction may result in electrical shock. This symbol is intended to alert the user to the pres-ence of important operating, maintenance, and ser-vicing instructions in the literature accompanying this unit. Failing to comply with this instruction may result in a hazard. DO NOT OPEN THE COVER • Dangerous voltages inside.• No serviceable parts inside.• Refer to qualiﬁed service personnel.• Unit must be disconnected from power prior to servicing.• Unit has tamper-evident labeling that indicates when the cover has been removed.

ContentsFiretide HotPort Outdoor Wireless Mesh Node . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2What is a Firetide Mesh Network? .........................................................2Firetide High-Performance Mesh Network ..................................................3High Capacity .......................................................................3Scalable ...........................................................................3Reliable ...........................................................................3Wireless Mesh Network Applications .......................................................4Wi-Fi Networks ......................................................................4Multiple Services over the Mesh ..........................................................4Video .............................................................................4Voice over IP ........................................................................4Data ..............................................................................4Printing ...........................................................................4Provide Ethernet Anywhere .............................................................4High-Performance Nodes ...............................................................4Indoor/Outdoor Operation .............................................................42.4 GHz and 5 GHz Spectrums ...........................................................4Best Price/Performance ...............................................................5Easy to Deploy/Instant Mesh Network .....................................................5Product Features ......................................................................5Mesh Management Using HotView Software .................................................5Security ...........................................................................5Packet Filtering ......................................................................5VLANs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Trafﬁc Prioritization ..................................................................5Network Gateway Interconnects ..........................................................6Radio Settings .......................................................................6Integrated Two-Port 10/100 Switch .......................................................6Speed and Duplex Settings .............................................................6Transmit Power Control ................................................................6Example Networks/Applications .........................................................6Managing the Mesh Network .....................................................7Getting Started with HotView Mesh Management Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Restoring Default Settings ..............................................................8HotPort Factory Default Settings .........................................................8Appendix A Contacting Firetide ...................................................9Appendix B Regulatory Notices ..................................................10Appendix C Countries of Operation ...............................................11

Firetide HotPort Wireless Mesh NodesThe Firetide™ HotPort™ High-Performance Mesh Network pro-vides a high-capacity, self-healing wireless mesh backbone for indoor and outdoor networks. The HotPort system enables mul-tiple network services and standard Ethernet devices to operate on the wireless backbone, creating secure and reliable wireless networks for video surveillance, voice, and data. All HotPort mesh nodes, indoor or outdoor, connect wirelessly to other nodes to form a high-performance wireless mesh network. Ethernet packets are automatically switched across the mesh, in a manner analogous to an Ethernet switch, using AutoMesh™, a proprietary protocol developed by Firetide. AutoMesh has been optimized for efﬁciency in wireless mesh environments.Models are available for operation at 2.4 GHz for high capacity and maximum range or at 5 GHz for high capacity and minimal interference from 2.4 GHz devices. For use on US Public Safety bands, a 4.9 GHz unit is available. This frequency may only be used by FCC-licensed Public Safety agencies.A Firetide mesh is completely portable, so relocating your entire network is as easy as taking your HotPort nodes with you to your new site, leaving no wires behind. The HotPort FamilyHotPort nodes are available in both indoor and outdoor models, and with a range of single-band and multiple-band radios. Outdoor NodesHotPort 3200 and 3600 series outdoor mesh nodes have weather-proof enclosures and connect wirelessly to otherHotPort nodes to form a high-performance wireless mesh network. 3200 series nodes operate at 2.4 GHz or at 5 GHz. Units designed for use on the 4.9 GHz Public Safety band are available in the US for use by FCC-licensed Public Safety agencies. 3600 series nodes are single band, and are available in 2.4 GHz and 5 GHz models. All models feature a built-in, dual-port 10/100 Ethernet switch. Both Ethernet ports are weatherproof. Port 1 accepts power from PoE; port 2 can power other PoE equipment. A removable sun-shield and a mounting bracket are provided with each unit. Indoor NodesHotPort 3100 and 3500 series mesh nodes provide fast and easy indoor network deployment. They are plenum-rated and feature a four-port 10/100 Ethernet switch for connecting devices at any location to a wireless mesh backbone. 2 HotPort 3200 Series User Guide The HotPort high-performance mesh network is the third genera-tion of mesh networking products from Firetide, a leading devel-oper of wireless mesh networks. The HotPort system is a multi-function mesh network that enables standard Ethernet devices, such as access points, surveillance cameras, IP telephones, net-work servers, and printers to access networking services on the wireless mesh backbone. Mesh networking can be compared to the Internet, where data can be rerouted onto other paths if one path becomes disabled or congested. Losing a node or two or a link won’t bring down the entire mesh network. Unlike other WLAN technologies, a mesh network’s reliability and scalability can actually be improved by adding more nodes and enriching the density of the mesh. More redundant paths mean the network in aggregate can handle far more data trafﬁc, and is therefore quite scalable. Mesh networks are ideal whenever the network must be reliable, scalable, and ﬂexible. They are very portable and can adapt to many different physical environments.What is a Firetide Mesh Network?Model & SKU Use Band RF Output Power Data Rate Default Channel3101 Indoor 2.4, 5 GHz standard 10 Mbps 2.462 GHz DSSS, Ch 113103 Indoor 2.4, 5 GHz standard 25 Mbps 2.462 GHz DSSS, Ch 113100/PS Indoor, Public Safety 2.4, 4.9, 5 GHz standard 25 Mbps 2.462 GHz DSSS, Ch 113500-2401 Indoor 2.4 GHz high 10 Mbps 2.462 GHz DSSS, Ch 113500-5001 Indoor 5 GHz high 10 Mbps 5 805 GHz OFDM, Ch 1613500-2403 Indoor 2.4 GHz high 25 Mbps 2.462 GHz DSSS, Ch 113500-5003 Indoor 5 GHz high 25 Mbps 5 805 GHz OFDM, Ch 1613203 Outdoor 2.4, 5 GHz standard 25 Mbps 2.462 GHz DSSS, Ch 113200/PS Outdoor, Public Safety 2.4, 4.9, 5 GHz standard 25 Mbps 2.462 GHz DSSS, Ch 113600-2400 Outdoor 2.4 GHz high 25 Mbps 2.462 GHz DSSS, Ch 113600-5000 Outdoor 5 GHz high 25 Mbps 5.805 GHz OFDM, Ch 161Note: Data Rates are typical for single-hop connections.Summary of HotPort Models

Firetide Instant Mesh Networks 3Firetide High-Performance Mesh NetworkHigh CapacityThe HotPort mesh network provides exceptional performance and scalability and is designed especially for high-bandwidth/low-latency applications, such as real-time video, voice, and large Wi-Fi HotZones. The HotPort system features high-performance hardware and software that provides up to 25 Mbps sustained throughput across the mesh network. Scalable The HotPort mesh network has a scalable architecture, allowing expansion of the network from just a few nodes to many. To add more nodes, you can simply copy the conﬁguration from an exist-ing node to the new nodes. Multiple mesh networks operating on different radio spectrums or IP addresses can be physically con-nected to each other to expand the overall network, while still retaining their separate mesh identities. ReliableThe self-healing architecture of the HotPort mesh network and its redundant paths between nodes make it very reliable and fault tolerant. Mesh trafﬁc will reroute over a different path automati-cally if a path becomes obstructed or if a node is taken out of service or moved to another location.Firetide Mesh Network with Indoor and Outdoor Wireless Mesh Nodes)NTERNET)NTERNET#ORPORATE,!.3URVEILLANCE#AMERA6,!.TRUNK!CCESS0OINT6,!.TRUNK7ORKSTATION#ABLE-ODEM$3,-ODEM)NTERNET'ATEWAY#ABLE-ODEM$3,-ODEM)NTERNET'ATEWAY(OT0ORT/UTDOOR-ESH.ODE(OT0ORT/UTDOOR-ESH.ODE(OT0ORT)NDOOR-ESH.ODE(OT0ORT)NDOOR-ESH.ODE(OT0ORT)NDOOR-ESH.ODE(OT0ORT)NDOOR-ESH.ODE

Best Price/PerformanceWireless mesh networks can signiﬁcantly reduce the labor costs and lead times of network installation by eliminating a signiﬁ-cant amount of backhaul cabling. However, these savings will not be realized if the cost of the mesh hardware is too high or if too many nodes or auxiliary devices are needed to build a reliable mesh. Firetide HotPort mesh networks provide exceptional value with the lowest cost per node of any high-capacity mesh solution. HotPort mesh nodes provide excellent wireless connectivity for maximum coverage at each location, and no auxiliary servers or additional devices are required to support larger node popula-tions.Easy to Deploy/Instant Mesh NetworkFiretide HotPort mesh networks greatly simplify network deploy-ment by eliminating network backhaul cabling and streamlining the process of provisioning and managing wireless networks. Af-ter basic conﬁguration and startup, HotPort nodes automatically ﬁnd each other to form the wireless mesh. The network automati-cally heals itself if a node goes down or if a path between nodes is blocked. Minimal network management is required to deploy the network. Network management is provided with an intuitive graphical interface on a workstation that can be connected ei-ther directly to the mesh or remotely via the Internet.Mesh Management Using HotView SoftwareHotView™ mesh management software provides live monitoring, as well as local and remote management of Firetide HotPort wire-less mesh networks. The software features an intuitive graphical user interface and provides complete access to all mesh and indi-vidual node settings, including security, VLANs, trafﬁc prioritiza-tion, radio power controls, and Network Gateway Interconnects. Live monitoring features include mesh and node statistics and a graphical view that uses node icons to indicate active con-nections. Users can also import graphics of ﬂoor plans or maps. The icons for each node can be moved over the graphics to show where they are physically located. SecurityThe HotPort mesh network includes several layers of security, in-cluding AES key and WEP encryption. AES (Advanced Encryption Standard) encryption can be used to protect data exchanged between any two nodes in a wireless mesh. When AES encryption is enabled for a wireless mesh, all payload data leaving the nodes in the mesh is encrypted using 128- or 256-bit keys. The data remains encrypted as it passes through the intermediate nodes and is only decrypted at the end node where it leaves the mesh network. This provides end-to-end security for the customer data passing through the HotPort wire-less mesh. WEP (Wired Equivalent Policy) supports 40/64- and 104/128-bit encryption to protect all trafﬁc on the mesh, including routing and management trafﬁc. This can be used to protect trafﬁc over the wireless links.For additional security, a proprietary mesh protocol prevents non-HotPort devices from participating on the mesh. Secure network access can also be provided for applications that do not allow Wi-Fi client services by connecting computers to the mesh directly using cables connected to the Ethernet ports on a Hot-Port node.Packet FilteringHotPort nodes can ﬁlter packets based upon the MAC address of the trafﬁc. You can conﬁgure each Ethernet port to deny or per-mit access for trafﬁc coming from or to speciﬁc devices (identiﬁed by the devices’ MAC addresses).VLANs The HotPort mesh network includes support for virtual local area networks (VLANs) to enable trafﬁc to be separated into smaller groups and application-speciﬁc LANs. VLANs allow small groups of users to operate within their own private space on the mesh, and they can also improve mesh performance by directing trafﬁc onto speciﬁc VLAN routes. The HotPort mesh supports 802.1Q VLAN tag-ging of packets entering and exiting the mesh. You can conﬁgure each Ethernet port to operate as part of a VLAN. A HotPort wireless mesh can support multiple VLANs. You can assign ports to different VLANs. Only ports belonging to the same VLAN can switch trafﬁc among themselves. You can create up to 16 logically separated VLAN networks within a single mesh. The HotPort mesh also supports VLAN trunks.Trafﬁc PrioritizationThe HotPort system provides three trafﬁc prioritization levels (Low, Medium, or High) to prioritize trafﬁc on the mesh. This helps ensure that certain types of trafﬁc requiring high through-put or continuous service, such as voice, take precedence over other forms of trafﬁc. Every port on every node on the mesh can be set to any of these three priority levels. Product FeaturesBelow are descriptions of some of the HotPort wireless mesh network’s features.Firetide Instant Mesh Networks 5

6 HotPort 3200 Series User GuideNetwork Gateway InterconnectsThe HotPort mesh network allows multiple mesh portals for ef-ﬁcient access to external network services, such as the Internet. This capability enables high throughput and redundancy for ex-ternal services and optimizes the transport of trafﬁc though the mesh. HotPort mesh nodes can also be assigned to speciﬁc portal groups (called “Gateway Groups”) to further increase the efﬁ-ciency of each portal. You conﬁgure portals by deﬁning Network Gateway Interconnects (NGIs).Each Gateway Group can support up to 16 NGIs and you can de-ﬁne up to 8 Gateway Groups. Each node on the mesh can have only one Gateway Group interconnect. Gateway groups are not required when connecting to different network domains or if only one NGI is being used.The NGI feature provides both load balancing and redundancy when accessing various network services. This helps provide bet-ter wireless mesh data throughput because it allows packets to enter and exit the wireless mesh at the entry/exit point closest to the packet’s destination, thereby conserving wireless bandwidth and reducing the number of hops required to reach the desired destination. Radio SettingsHotPort wireless mesh nodes support a range of radio options in the 2.4 GHz and 5 GHz bands, and the 4.9 GHz Public Safety band for US use. The selected radio mode is applied to the entire wireless mesh. You can use the HotView management software to display and modify the radio transmit power level for each node.Integrated Two-Port 10/100 SwitchYou can use the HotPort 3200/3600 series’ two Ethernet ports to connect any Ethernet-capable client device to the mesh. The HotPort node can switch trafﬁc between these devices even when there is no mesh created. When multiple HotPort nodes form a wireless mesh, trafﬁc can be switched between any clients con-nected to any HotPort node that is part of the mesh.Speed and Duplex SettingsYou can conﬁgure each Ethernet port for 10 or 100 Mbps speed or for automatic speed negotiation. Network trafﬁc between a HotPort node and devices connected to its Ethernet ports trav-els up to full wire rate (10 or 100 Mbps). Each port can also be conﬁgured for full- or half-duplex operation. In addition, you can enable and disable individual ports.The Ethernet ports support auto MDIX, which allows you to use either straight-through or crossover cables to connect the Hot-Port node to other devices.Transmit Power ControlYou can display and modify the radio TX power level on a per node basis utilizing the HotView™ management software. The maxi-mum power (that is, 100%) is a factory-conﬁgured value that is unique to each country of operation, each channel of operation, and each antenna conﬁguration, and has been determined to be within an authorized limit. This value cannot be changed. Howev-er, using the HotView software, a mesh administrator can set any node to operate at a reduced percentage of this maximum power (for example, 75%, 50%, or 25%; the default setting is 75%). The administrator can restore the HotPort node to its approved maxi-mum power by setting the power level back to 100%.Note: Transmit power control adjustments affect the node radio, so care must be exercised when making adjustments on an existing network, as the reduced power level may cause the node to lose con-nectivity with other mesh nodes.Note: Adjusting the power incorrectly could have an adverse effect on proper mesh operations.If you are not sure what the power should be adjusted to, it is best to leave it at its default conﬁguration. If you need additional technical assistance, please contact your Firetide dealer.Example Networks/ApplicationsBelow are some examples of how you can use HotPort wireless mesh networks in your workplace. • Provide Ethernet service over a wireless backbone to build-ings where wired solutions via CAT5 cabling or ﬁber is im-practical or too expensive • Connect access points to networks from locations where it is impractical to run cable to the access points • Connect security cameras to monitor remote locations

Firetide Instant Mesh Networks 7Managing the Mesh NetworkHotView and HotView Pro mesh management software provides a convenient, browser-based interface for monitoring all of the HotPort nodes on your mesh network. The HotView software is a Java-based application compatible with most Internet browsers and platforms, including Windows® and Linux®. HotView and HotView Pro are described in detail in the HotView User Guide and HotView Pro User Guide. You should refer to these; the following summary of initial installation is extremely brief.To conﬁgure the mesh, connect to the mesh utilizing the default conﬁguration and then change the desired settings using Hot-View. The software lets you change the settings (ESSID, chan-nel, encryption, IP address, and so on) on all nodes, rather than changing one at a time. This will save you time and ensure that the entire mesh is conﬁgured the same way. The HotView mesh management software provides an easy way to monitor and manage the mesh and your HotPort nodes. Be-cause wireless connections between HotPort nodes are invisible, this software lets you “see” which units are within direct range of each other. The HotView software also provides additional se-curity and optional conﬁguration features. Registered users can download the HotView software and documentation from the Firetide web site: www.ﬁretide.com/support. 1. Be sure all of your HotPort nodes are installed and pow-ered. 2. Connect your workstation’s network adapter directly to any one of the HotPort nodes using an Ethernet cable. 3. Turn on your workstation and conﬁgure your TCP/IP settings to: 1. IP address: 192.168.224.10 2. Subnet mask: 255.255.255.0 3. Gateway is not usedRefer to your operating system documentation to conﬁgure the static address deﬁned in step 3.Note: See the HotPort 3200 / 3600 Hardware Installation Guide for instructions on installing your HotPort outdoor nodes.Getting Started with HotView Mesh Management SoftwareYou are now ready to check your mesh conﬁguration using the HotView mesh management software. For complete informa-tion on HotView mesh management features and more detailed instructions on its operation, install the software from the CD provided in the HotPort package or download the latest HotView User Guide, available at www.ﬁretide.com/support.The steps below describe how to launch the HotView software un-der Windows. Your operating system may have a different proce-dure for launching applications. If necessary, refer to your oper-ating system’s documentation for instructions on how to launch applications. 1. Install the HotView mesh management software as described in the HotView User Guide. 2. From the Windows Desktop, click on the Start button. 3. Click on All Programs and select HotView. The Login screen will appear. 4. Enter the following information to log into the mesh network: • Mesh IP address: 192.168.224.150 • Username: admin • Password: ﬁretide 5. Click on Login. 6. Wait for your computer to connect to the mesh. This may take a few seconds to several minutes, depending on how many nodes are in the mesh. You should see a screen with a list of all of the HotPort units on the mesh.

8 HotPort 3200 Series User GuideRestoring Default SettingsYou can restore your HotPort node to its factory default settings using the provided HotPort 3203 reset application. This application is provided on the CD-ROM disc included in the HotPort package.Note: To reset a HotPort to its factory defaults, you must run the reset application within 3 minutes after the HotPort boots up. 1. Install the reset application on a workstation. If running Windows, install the Windows application (3200factoryreset.exe); if running Linux, install the Linux version of the application (3200factoryreset.bin). 2. Connect the workstation’s network adapter directly to an available Ethernet port on the HotPort using an Ethernet cable. Make sure the HotPort is powered. 3. Start up and run the factory reset application.HotPort Factory Default SettingsAES encryption: DisabledWEP encryption: DisabledMesh IP address: 192.168.224.150Ethernet ports: All ports enabledHotView username: adminHotView password: ﬁretideRadio Power = 75% of approved maximum powerESSID = HOTPORT_MESHDefault radio channel depends on model; refer to the table on page 2.After a factory reset, you will need to specify the country code for Model 3203 HotPorts. All other mdoels are US-only. Refer to the HotView User Guide for information on using the HotView software to conﬁgure your HotPort nodes.

Firetide Instant Mesh Networks 9Appendix A Contacting FiretideAs a Firetide customer, you are entitled to receive free support ser-vices on our web site and from your authorized Firetide dealer.Register with Us Now to Access our Support Web SiteRegistering as a customer on our web site entitles you to free information and materials to help you get the most from your Firetide mesh network. Visit www.ﬁretide.com/support for infor-mation on becoming a registered customer and for access to our support materials.Dealer Provided Technical Support and Warranty ServicesIf you need additional technical assistance that is not available on our web site, please contact your Firetide dealer directly. All authorized Firetide dealers are trained and authorized to provide technical support and warranty services for our products and have qualiﬁed technical staff available to help you build and maintain your Firetide mesh network.Product ReturnsPlease contact your Firetide dealer for instructions on returning defective or damaged products for repair or replacement. Do not return products to Firetide, Inc. Please keep all original packaging materials in the event they are needed to return the product for servicing.Sales AssistanceIf you need additional HotPort wireless mesh nodes or accesso-ries, please contact your Firetide dealer directly. If you do not know your dealer’s name, simply email sales@ﬁretide.com and we will send you the dealer information you need. To help us provide the best service possible, be sure to include your phone number, address, and the serial numbers of the HotPort nodes at your loca-tion.

10 HotPort 3200 Series User GuideAppendix B SpeciﬁcationsWireless InterfaceThese tables describes the technical limits of the nodes. Various country restriction may limit available choices. Channels avail-able for use subject to country-speciﬁc regulatory approvals.• Dynamic Frequency Selection (DFS)• Transmit Power Control (TPC)Model Use Bands3203 Worldwide 2.4, 5 GHz3200/PS US Public Safety 2.4, 4.9, 5 GHz3600-2400 US only 2.4 GHz3600-5000 US only 5 GHzModel Bands (GHz) Max TX Power Sensitivity, dBm3203 2.400-2.497 DSSS2.400-2.497 OFDM4.900-5.000 (J)5.150-5.2505.250-5.3505.725-5.850100 mW100 mW100 mW 50 mW100 mW100 mW1 Mbps: -96; 11 Mbps: -896 Mbps: -93; 54 Mbps: -756 Mbps: -92; 54 Mbps: -726 Mbps: -92; 54 Mbps: -726 Mbps: -92; 54 Mbps: -726 Mbps: -92; 54 Mbps: -723200/PS 2.400-2.484 DSSS2.400-2.484 OFDM4.9 (US PS)5.150-5.2505.250-5.3505.725-5.850100 mW100 mW100 mW 50 mW100 mW100 mW1 Mbps: -96; 11 Mbps: -896 Mbps: -93; 54 Mbps: -756 Mbps: -92; 54 Mbps: -726 Mbps: -92; 54 Mbps: -726 Mbps: -92; 54 Mbps: -726 Mbps: -92; 54 Mbps: -723600-2400 2.400-2.484 DSSS2.400-2.484 OFDM 400 mW 1 Mbps: -96; 11 Mbps: -906 Mbps: -93; 54 Mbps: -743600-5000 5.150-5.2505.250-5.3505.725-5.850 50 mW250 mW400 mW6 Mbps: -92; 54 Mbps: -726 Mbps: -92; 54 Mbps: -726 Mbps: -92; 54 Mbps: -72Mesh Protocol• Firetide AutoMesh ProtocolEncryption• 40 bit, 104 bit WEP keys• 128 bit, 256 bit AES keysAntennas• Two detachable 5 dBi omni directional, vertical polarization, dual band antennas, RP-TNC (included for network staging only)• Single detachable, high gain, spectrumspeciﬁc, omni directional and directional antennas available (order separately). See Firetide Antenna Guide.Network Ports• Dual 10/100 Mbps Ethernet ports with weatherproof connectors• IEEE 802.3, 802.3u compliant• CSMA/CD 10/100 autosense• Power over Ethernet 802.3afEnclosure• Cast aluminum NEMA-4X/IP66 enclosure• Two antenna connectors (TNC reverse polarity)• One weatherproof power connector• Two weatherproof Ethernet connectors• System indicator LEDs (power, mesh, fault)• Physical security via lockable mounting bracket• Weight: 4.85 lbs (2.2 Kg) with sun shield• Dimensions: 9.84” x 7.80” x 2.69” (25 cm x 19.8 cm x 6.82 cm)Power• Input voltage: 16 VDC @ up to 2.2 A• External power supply: 100-240 VAC, 50/60 Hz• Power consumption:• Up to 14 W with no PoE load• Up to 35 W with PoE load• Port 1: IEEE 802.3af compliant PoE (PD; accepts power)• Port 2: IEEE 802.3af compliant PoE (PSE; delivers power) Note: you cannot pass PoE through the HotPort to a downstream device.Regulatory Agency CertiﬁcationsContact your Firetide dealer for product availability and certiﬁca-tions for your country.Environmental Speciﬁ cations• Operating temperature: -20º C to +55ºC• Storage temperature: -40º C to +80º C• Humidity (non-condensing): 5% to 95%• Storage humidity (non-condensing): 5% to 95%Mesh Management Software• HotView mesh management software (bundled)• HotView Pro™ mesh management software (optional)Warranty• One year limited warranty (see warranty card for details)Included Accessories• Lockable bracket for pole and wall mounting• External power transformer (indoor rated) with 10m DC power cable• Removable sun shield• One weatherized Ethernet transition cable with watertight RJ-45 coupling• Staging antennas, 1 pairOptional Accessories• Weatherized Ethernet transition cable with watertight RJ-45 coupling• Weatherized outdoor power supply kit• Luminaire photcell socket power tap for use with weatherized power supply unit)

Firetide Instant Mesh Networks 11Appendix C Countries of OperationUSA - All Models• Approved for operation in the 2.400-2.484 GHz band in DSSS and OFDM modes.• Approved for 4.9 GHz operation by licensed Public Safety agencies, per FCC regula-tions.• Approved for operation on the 5.150-5.250 GHz, 5.250-5.350 GHz, and 5.725-5.825 GHz bands in OFDM mode. Canada - HotPort 3203 only• Approved for operation in the 2.400-2.484 GHz band in DSSS and OFDM modes.• Approved for operation on the 5.150-5.250 GHz, 5.250-5.350 GHz, and 5.725-5.825 GHz bands in OFDM mode. Japan - HotPort 3203 only• Approved for operation in the 2.400-2.497 GHz band in DSSS and OFDM modes.• Approved for operation in the 5.150-5.250 GHz band in OFDM mode. Korea - HotPort 3203 only• Approved for operation in the 2.400-2.483 GHz band in DSSS and OFDM modes.• Approved for operation in the 5.150-5.250 GHz, 5.250-5.350 GHz, and 5.725-5.825 GHz bands in OFDM mode. New Zealand - HotPort 3203 only• Approved for operation in the 2.400-2.484 GHz band in DSSS and OFDM modes.• Approved for operation in 5.150-5.250 GHz, 5.250-5.350 GHz, and 5.725-5.825 GHz bands in OFDM mode.Australia - HotPort 3203 only• Approved for operation in the 2.400-2.484 GHz band in DSSS and OFDM modes.• Approved for operation in 5.150-5.250 GHz, 5.250-5.350 GHz, and 5.725-5.850 GHz bands in OFDM mode.Singapore - HotPort 3203 only• Approved for operation in the 2.400-2.484 GHz band in DSSS and OFDM modes.• Approved for operation in 5.150-5.250 GHz, 5.250-5.350 GHz, and 5.725-5.850 GHz bands in OFDM mode.China - HotPort 3203 only• Approved for operation in the 2.400-2.484 GHz band in DSSS and OFDM modes.• Approved for operation in 5.725-5.850 GHz band in OFDM mode.Hong Kong - HotPort 3203 only• Approved for operation in the 2.400-2.484 GHz band in DSSS and OFDM modes.• Approved for operation in 5.150-5.250 GHz, 5.250-5.350 GHz, and 5.725-5.850 GHz bands in OFDM mode.India - HotPort 3203 only• Approved for operation in the 2.400-2.484 GHz band in DSSS and OFDM modes.• Approved for operation in 5.150-5.250 GHz, 5.250-5.350 GHz, and 5.725-5.850 GHz bands in OFDM mode.UK - HotPort 3203 only• Approved for operation in the 2.400-2.4835 GHz band in DSSS and OFDM modes.• Approved for operation in 5.150-5.250 GHz, 5.250-5.350 GHz, and 5.400-5.700 GHz bands in OFDM mode.France - HotPort 3203 only• Approved for operation in the 2.400-2.4835 GHz band in DSSS and OFDM modes.• Approved for operation in 5.150-5.250 GHz and 5.250-5.350 GHz bands in OFDM mode.Germany - HotPort 3203 only• Approved for operation in the 2.400-2.4835 GHz band in DSSS and OFDM modes.• Approved for operation in 5.150-5.250 GHz, 5.250-5.350 GHz, and 5.400-5.700 GHz bands in OFDM mode.

12 HotPort 3200 Series User GuideAppendix D Regulatory NoticesFCC Class B NoticeThis device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:1. This device may not cause harmful interference.2. This device must accept any interference received, includ-ing interference that may cause undesired operation.FCC Part 15 NoteThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reason-able protection against harmful interference in a residential installation. This equipment generates, uses and can radi-ate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful in-terference to radio communications. However, there is no guarantee that interference will not occur in a particular in-stallation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the follow-ing measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and re-ceiver. • Connect the equipment into an outlet on a circuit dif-ferent from that to which the receiver is connected. • Consult the dealer or an experienced radio/television technician for help.FCC Part 90 NoteThis equipment has been tested pursuant to FCC Part 90, DSRC-C mask certiﬁcation, and is approved for use in the US on Public Safety bands by licensed Public Safety agencies.ModiﬁcationsAny modiﬁcations made to this device that are not approved by Firetide, Inc. may void the authority granted to the user by the FCC to operate this equipment.FCC Radiation Exposure StatementThe antenna used for this transmitter must be installed to pro-vide a separation distance of at least 35 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. OEM Integrators, end-users and in-stallers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance.Public Safety BandPursuant to Part 90.1215, use of antennas with gain greater than 9 dBi and up to 26 dBi in the 4.940 – 4.990 GHz Public Safety band is permissible without reduction of TX output power. The antenna shall have a directional gain pattern in order to meet the require-ment of point to point and point to multi-point operation.

Navigation menu