FOXCONN SZ901PWB Notebook User Manual 2

FOXCONN INTERNATIONAL INC Notebook 2

Contents

user manual2

1723123 Do not remove the battery while the Netbook is still running. This may damage the data on the hard disk. CAUTION!Removing the BatteryStep 1: Shut down the Netbook. Disconnect all cables and devices. Step 2: Turn the Netbook over and unlock the battery by pushing the Battery Lock outwards. Step 3: Push the Battery Latch outwards and hold it in place with your nger. Now use the other hand to pull the battery out.
182. Connecting the Power SupplyStep 1: Insert the round end of the power supply transformer into the charging port on the left side of the Netbook. Step 2: Insert the other end of the power supply transformer into a power socket.The power connector for the power socket may vary depending on the local national standards. The appropriate connector will be bundled with your Netbook. Please always use the adapter when connecting the power supply. The connector shown here may not match the type included in the box and is provided for reference purposes only. CAUTION!3. StartupStep 1: Open the screen of your Netbook.
19Step 2: Turn on the machine by pressing the Power Button.Power Button4. Emergency ShutdownWhen the Netbook cannot be shut down through normal means, please press and hold the Power Button until the Netbook powers off.
1101-3 Using the Touchpad1. Introduction to the TouchpadThe touchpad is like a computer mouse. It senses the pressure from the user's nger and generates a voltage that is used to control the cursor's movements and issue commands. The touchpad senses nger movements. Simply move one nger across the touchpad to control the movement of the cursor on screen. Below the touchpad is two buttons. The left button is like the left mouse button and is used for selecting options or launching programs on screen. The right button works the same way as the right mouse button.2. Single Tap/ Single Click To select a window function or press a button icon, move your nger across the touchpad to move the cursor to the window or button to select. Now tap the touchpad with your nger to perform the action. This action is equivalent to pressing the left mouse button. You can also press the left touchpad button for the same effect. 3. Double Tap/ Double ClickTo open a le or document, move your nger across the touchpad to move the cursor to the le you wish to open. Now quickly tap the touchpad twice with your nger to perform the action. This action is equivalent to pressing the left mouse button twice. You can also press the left touchpad button twice for the same effect. 4. DragMove your nger across the touchpad to move the cursor to the object you wish to drag. Now hold down the left touchpad button with one hand and move the cursor to the desired location. Release the button and complete the drag operation. You can also double tap the object you wish to drag and keep the nger on the touchpad after the second tap to perform the drag operation with one hand. TouchpadLeft Button Right Button
This chapter introduces the following information for you:■ Overview■ Using Web Camera■ Special Function Keys■ MMC/SD/MS Dummy Card■ Using WWAN■ Using Wireless LAN
2122-1 OverviewAfter turning on the Netbook, when you log in Netbook's pre-loaded FoxOS system, the following screen will appear:2-2 Using web cameraClick "Play"->"Webcam" to open the web camera, you can take photo and record through the camera. About detailed information please refer to help page.Click "Setting" to open the page to optimize the system.Click "Help" to open the page, please refer to the content of the page about detailed description of the system.From left to right is in turn:a. Show Desktop icon b. Bluetooth icon(optional)c. iBus Input Method icon d. Network Connection status icone. Power icon f. Volume icong. Exit icon h. Time iconThe four parts provide various applications to meet the needs of your work, life and entertainment, detailed refer to help page.You can click these icons to go to the corresponding utilities.
2132-3 Special Function KeysThe following denes some special function keys on the netbook.Function Keys DescriptionFn + F1 WWAN on or offFn + F2 Wireless LAN on or offFn + F3 Touchpad on or offFn + F4 Switches to the external displayFn + F5 Audio on or offFn + F9 To terminate some applicationsFn + F10 Toggles the "Print Screen" key to initiate screen capture utility to capture, save or print the contents of desktopFn + F11 F12 / Enters into the dialog box of "Save As" in Windows Ofce applicationsFn + Page Up Presses to move the cursor to the beginning of the lineFn + Page Down Presses to move the cursor to the end of the lineFn + Ins "Number Lock" on or offFn + Del "Scroll Lock" on or offFn + Esc In S3 modeFn + (up arrow) Increases the display brightnessFn + (down arrow) Decreases the display brightnessFn + (left arrow) Decreases the system volumeFn + (right arrow) Increases the system volume2-4 MMC/SD/MS Dummy CardThere is a dummy card in our Netbook, the gure is as shown below. The main function of the card is to prevent dust into the computer. When you use the MMC/SD/MS card slot, press down the dummy card with your nger and take the popping card out.
2142-5 Using WWAN (optional)Let me take EM770 module as an example to simply introduce how to connect WWAN in Windows XP, the steps are as below. Please refer to the le "utps_content_concept_00001.html" for details about the WWAN, its path is as below: In system path -> Program Files -> Mobile Partner -> usermanual -> en-us -> usermanual ->utps_content_concept_00001.html1. Double click "Mobile Partner" on desktop to open the gure as shown below:2. Click "Tools" - > "Options", and select "Prole Management" in popping window, the gure is shown as below:3. Click "New" and input the name in "Prole Name" column, like Chinamobile, then click "Save" and "Ok".
2154. Click "Connect" to start the connection.5. You can access the internet when the gure is shown as below.
216Remark - How to install the SIM cardPlease install the SIM card according to the following details:Power off the Netbook and shut down power supply, then remove the battery (please refer to page 7 for details about removing the battery), and you will see the SIM card slot, as the picture shown. Please insert the SIM card into the slot (as the arrow shown) and make sure that the gold pins of SIM card are downward.2-6 Using Wireless LANYou can use wireless LAN with the Netbook. This part mainly introduces wireless LAN and its connection. I: Introduce wireless LAN 1. Wireless LAN:Wireless networks use radio waves as information transmission medium to consist of wireless LAN (WLAN), the main difference lies in the wireless networks using wireless technology instead of string. 2. Wireless card and Access wireless network:Wireless card is a wireless terminal device which uses the wireless connection with the coverage of the wireless LAN. You can access wireless network, if there is a wireless router or the coverage of wireless AP around (Please refer to the wireless router's manual about its connections and settings)；Attach a device to the Netbook and enclose a card as mobile phone card inside when you go telecommunication business hall to handle wireless. After that you can surf the Net wirelessly. II: Connecting wireless LANPress "Fn + F2" to turn on the wireless LAN of the Netbook, the system will automatically search the available wireless network around and connect it. Or click icon to manually choose the Internet connection.If password is required, enter the password of wireless LAN to realize wireless connection.Please do not insert or pull out the SIM card when power-on, otherwise the data may lose or the card would be damaged.WARNING!SIM card slot
This chapter introduces how to install Windows XP system for you, including following information:■ Install a new Windows XP system■ Install drivers in new Windows XP
318Install Windows XP in NetbookBy default, the Netbook has been installed FoxOS system for you. But if you do not like the operation system interface, you can install Windows XP by yourself. What kinds of hardware and software you need here :1. An USB DVD drive.2. A Netbook driver CD.3. Windows XP Install CD.Before we continue :■ Shut down your computer.■ Connect the USB DVD drive to an USB port of Netbook and connect the power cord to AC power.3-1 Install a new Windows XP system1. Press <Del> to enter BIOS setup during POST, set the "1st Boot Device" to "CD/DVD" in "Boot" menu, save changes and exit BIOS. The gure is as shown below:2. Insert the Windows XP Install CD into the USB DVD drive. The computer will reboot, and it will start installing Windows XP Operating System. The gure is as shown below: Boot Settings Species the boot sequence from the Quick Boot [Enabled] available devices . Quiet Boot [Disabled] A device enclosed in Onboard LAN Boot ROM [Disabled] parenthesis has been disabled in the Boot Device Priority corresponding type 1st Boot Device [CD/DVD] menu. 2nd Boot Device [USB:Generic- SD/MM] 3rd Boot Device [CD/DVD] 4th Boot Device [Network] ←→ Select Screen 1st Hard Disk Drive [HDD:PM-FUJITSU MHZ] ↑↓ Select Item +- Change Field 1st Removable Drive [USB:Generic- SD/MM] F1 General Help 2nd Removable Drive [USB:Generic- MS/MS] F7 Discard Changes F10 Save and Exit ESC Exitv02.61 (C)Copyright 1985-2006, American Megatrends, Inc. Main Advanced Security Boot ExitBootBIOS SETUP UTILITY
3193. Press <Enter> to continue the installation and press <F8> to agree the Licensing Agreement. Windows will display the partition of your system. First of all, you had better press [D] to delete the partition, then you can press [C] to create partitions as many as you can, assign them C:, D: or E: logical drive name. In this example, we will create a 50GB partition C: and leave the remaining space as a partition D:. The gure is as shown below:4. Press <Enter> to install Windows XP. The process will ask you to format hard disk, copy les...etc, follow the installation steps until the system is installed completely.Windows XP Professional Setup Welcome to Setup.This portion of the Setup program prepares Microsoft(R)Windows(R) XP to run on your computer. ● To set up Windows XP now, press ENTER. ● To repair a Windows XP installation using Recovery Console, press R. ● To quit Setup without installing Windows XP, press F3. ENTER=Continue R=Repair F3=QuitWindows XP Professional Setup The following list shows the existing partitions andunpartitioned space on this computer.Use the UP ad DOWN ARROW keys to select an item in the list. ● To set up Windows XP on the selected item, press ENTER. ● To create a partition in the unpartitioned space, press C. ● To delete the selected partitions, press D. 114471 MB Disk 0 at id 0 on bus 0 on atapi [MBR] D: Partition2 [Unknown] 64464 MB < 64463 MB free> Unpartitioned space 8 MB Unknown Disk <There is no disk in this drive.> Unknown Disk <There is no disk in this drive.> ENTER=Install D=Delete Partition F3=QuitC:Partition1 [NTFS] 49999 MB < 48568 MB free>
3203-2 Install drivers in new Windows XP1. After installing Windows XP, you have to install necessary drivers before using the Netbook. Insert the Netbook driver CD to the USB DVD drive, waiting for a few seconds, the main menu will be displayed on your Netbook screen. 2. Clicking these options to install all the drivers for your system. You must rstly click "Intel Chipset Driver" to install and then click "One Click Setup" to install the other drivers left, or you can click each individual driver to install it manually.3. After all the drivers are installed, you need to restart your Netbook, then you can use it.
21AppendixRecovery of Linux systemI From DVD to recover system1 Boot from DVDPower on the computer, insert the system Installation DVD into the DVD drive, press "ESC" to select booting system from the DVD drive.2 Select the way of InstallationWhen the gure as below shows, select "Install and make recovery partition", the system will be installed and a recovery partition will be made. Or select "Install system only", the system will be installed without recovery partition, so recover system from hard disk is impossible.3 Click "Next", the warning box is shown as below: 4 Installing systemClick "Next" to format hard disk and install system. The gure is shown as below:
22Appendix5 After installing, click "Reboot" to restart the system.
23AppendixII From hard disk to recover system1 When you log in, according to the screen suggestion, press any key to enter Grub interface, the gure is as shown below:2 Select "FoxOS recovery" item and then press "Enter", the warning box is shown below:3 Select "Next", system warns the root partition(hd0, 0) will be formatted. The gure is as shown below:
24Appendix4 Click "Next" to format partition(hd0,0) and recover system from hard disk. The gure is as shown below:5 When the process is completed, please reboot the system.The gure is as shown below:
Federal Communications Commission Statement This device complies with FCC Rules Part 15. Operation is subject to the following two conditions: • This device may not cause harmful interference, and • This device must accept any interference received, including interference that may cause undesired operation. • This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the Federal Communications Commission (FCC) rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. The use of a shielded-type power cord is required in order to meet FCC emission limits and to prevent interference to the nearby radio and television reception. It is essential that only the supplied power cord be used. Use only shielded cables to connect I/O devices to this equipment. You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment. Note: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. “The manufacture declares that this device is limited to Channels 1 through 11 in the 2.4GHz frequency by specified firmware controlled in the USA.” RF exposure warning This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. The equipment must not be co-located or operating in conjunction with any other antenna or transmitter. The measured SAR levels evaluated are in compliance with the FCC RF exposure guidelines. Notebook SZ901P Max. SAR Measurement (1g) 0.00155W/kg

Navigation menu