FLYSKY RC MODEL TECHNOLOGY FLYSKYT4B 4CH Radio Control System User Manual FS CT6A

FLYSKY RC MODEL TECHNOLOGY CO., LTD 4CH Radio Control System FS CT6A

Contents

User manual part II

10.2.4G Operation notesThis is 2.4 G Frequency model products make of automatic address code.It use digital transmission mode, and this prevent outside interference effective active and passive.10.01 Matching (code)1. Install the battery to 2.4G transmitter and shut it down.2. ( 1）。Insert the matching lines to the channel Bat port of the receiver. Figure.3.Connect the receiver battery to any one of the channel port, on the same time the two LED are flashing and this means the receiver are going to the match status.4.Press and hold the button on the transmitter, and then switch on the power supply.6.Release the match button on the transmitter, take out the match line.5.（ )Observe the LED on the receiver, if found that the LED is not flash anymore and that means successful matched. This process about 10s7.Install the server and then test.8.If the tests fail, please repeat the action above.9.If the tests success, then insert the power supply port into BAT, match complete.(The above ways of match is only suitable on FLYSKY 2.4G products)Our products are well matched in the factory, you do not need to match by yourself. But if your are going to match the receiver with other transmitter, please follow the following steps:Match lineMatch key Figure 110.02 Boot1.Connect every part.2.Switch on the power supply.3.Connect the power supply.4.Receive LED light solid.5.Finish and use.2.4G 4 Channel remote system 8FS-T4BModel:Notes
Boot1.Cut off the receiver power supply.2.Cut off the transmitter power supply.Tx power ONTx power offRx power ONRx power offShut down10.03 Shut down：2.4G 4 Channel remote system 9FS-T4BModel:Notes
2.4G 4 Channel remote system 10FS-T4BModel:Notes11.Functional description11.01.1 Channel control .This channel is for aileron control 11.02.3 Channel control This channel is use for throttlecontrol.If you move the transmitter stick to the left,The airplane will inclined to the left and the airplane move left.（Figure.1）If you move the transmitter stick to the right,the airplane will inclined to the right and the airplane move right.（Figure.2）If you move the transmitter stick upwardthe power of airplane will increase and the airplane rise.（Figure.3）If you move the transmitter stick downwardthe power of airplane will decrease and the airplane drop.（Figure.4）Left RightFigure1Figure2Figure3Figure4Move leftMove rightRiseDrop上下
2.4G 4 Channel remote system 11FS-T4BModel:Notes11.03.2 Channel control This channel is use for forward and backward control.11.04.4 Channel control This channel is use for left and right turning control.Move forwardMove backwardLeft turning Right turningFigure1Figure2If you move the transmitter stick upward,the airplane will move forward.（Figure.1）。If you move the transmitter stick downward,the airplane will move backward.（Figure.2）。If you move the trans mitter stick to the left,The ai rplane will tur ning to the left.（Figur e.4）If you move the trans mitter stick to the left,The ai rplane will tur ning to the left.（Figur e.3）Figure.3 Figure.4Left RightUpDown
12.Professional terminology AIL:副翼ELE:升降舵THR:油门RUD:方向舵GEAR:PITCH:螺距FM:调频PPM:脉冲相位编码PCM:脉冲数据编码MODULE:调制RF:射频DR:双重比率TRAINER:教练STICK:操纵杆NULL:无功能REV:反向NOR:一般TRIM:微调SUB.TRIM:辅助微调HELI:直升机ACRO:飞机VR:电位器SW:开关UP:上DOWN:下DES:目标SOURCE:起源IDEL:特技2.4G 4 Channel remote system 12FS-T4BModel:Notes
13.Packaging with content listNO: Model Sum Remarks12367816 cha nnel 2.4Gtran smitter（FS -T4B)16 channel 2.4Greceiver(FS-R6A)Match(code)lineManual(FS-T4B)ChargerServer(FS-S036)111141OptionalOptional2.4G 4 Channel remote system 13FS-T4BModel:Notes
Http:www.flyskychina.comCopy right 2007@flysky co.,ltd
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation . Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help.

Navigation menu