Enlighted WS-2-00 Enlighted Wireless Room Control User Manual

Enlighted, Inc. Enlighted Wireless Room Control

User Manual

Page 5 Page 6 Page 1Copyright © 2014 Enlighted Inc. All rights reserved.All other brand or product names are trademarks oftheir respective companies or organizations.Technical SupportFor questions regarding the installation or operation ofthis product, contact EnlightedTechnical Support: support@enlightedinc.comCompany Contact InformationLocation: 930 Benecia Ave, Sunnyvale, CA 94085Phone: +1.650.964.1094Web: enlightedinc.comCA Contractor’s License: CCL# 980903FCC and Industry Canada Compliance InformationThis equipment has been tested and found to comply with the limitsfor a Class A digital device, pursuant to part 15 of the FCC Rules.These limits are designed to provide reasonable protection againstharmful interference when the equipment is operated in acommercial environment. This equipment generates, uses, and canradiate radio frequency energy and, if not installed and used inaccordance with the instruction manual, may cause harmfulinterference to radio communications. Operation of this equipmentin a residential area is likely to cause harmful interference in whichcase the user will be required to correct the interference at his ownexpense.USAThis device complies with Part 15 of the FCC Rules. Operation issubject to the following two conditions:•this device may not cause harmful interference, AND•this device must accept any interference received, includinginterference that may cause undesired operation.Changes or modifications not expressly approved by Enlighted Inc.could void the user's authority to operate the equipment.CanadaThis device complies with Industry Canada license-exempt RSSstandard(s). Operation is subject to the following two conditions:•this device may not cause harmful interference, AND•this device must accept any interference received, includinginterference that may cause undesired operation.Changes or modifications not expressly approved by Enlighted Inc.could void the user's authority to operate the equipment.Le présent appareil est conforme aux CNR d'Industrie Canadaapplicables aux appareils radio exempts de licence. L'exploitationest autorisée aux deux conditions suivantes:•l'appareil ne doit pas produire de brouillage, ET•l'utilisateur de l'appareil doit accepter tout brouillageradioélectrique subi, même si le brouillage est susceptible d'encompromettre le fonctionnement.CEThis device complies with the essential requirements and otherrelevant requirements of the R&TTE Directive (1999/5/EC). Theproduct is compliant with the following standards and/or othernormative documents. EN 62479, ETSI EN 301, EN 300•The equipment is Class 1 radio equipment which can be placedon the market and be put into service without restrictions inaccordance with article 1(3) of Commission Decision 2000/299/EC(Version July 2014).Figure 1: Enlighted Wireless Switch 2 (WS2)Wireless Switch 2 (WS2)Model WS-2-00Installation InstructionsShipped Components•Wireless switch version 2 (WS2)•Usage card•Back plate (with captive screws in place)•Cover plate•2 tapping screws•2 6-32 machine screwsTools You May Need•Phillips screw driver•Flat head screw driver94-01140-01 Rev01Model: WS-2-00FCC ID: AQQ-WS-2-00Industry Canada: 10138A-WS200
TroubleshootingPage 2 Page 3 Page 4Cautionary Suggestions•Installation and maintenance must be performed by aqualified electrician.•Installations and maintenance must be performed inaccordance with state, local, and national electricalcodes and requirements.Figure 5: Mounting SequenceProblem SolutionLEDs do not flashwhen a is buttonpressedThe energy in the battery mayhave drained. Check, and ifneeded, replace the battery(see Figure 4)Buttons do noteasily movewhen pressedReturn unit for replacementFigure 4: Opening the WS2’s case to access the batteryStepDescription1 Separate, if needed, the cover and backplates.2 Remove the plastic pull tab from the WS2 toallow the battery to come in contact with theterminals. (See figure 2)3 Press each button and verify that both thegreen and red LEDs flash and that the buttonmoves smoothly. (See figure 3)4 If the LEDs do not flash when a button ispressed, then check, and if needed, replacethe battery. The battery is accessed afteropening the case as shown in figure 4.5 Position the WS2 on either the wall or on ajunction box with the LEDs on the top and theEnlighted logo on the bottom. (See Figure 5)6 Use the provided tapping screws (or machinescrews for a junction box) to attach the WS2to the wall.7 Align the back plate (with the arrow pointingup) to the WS2. Affix the back plate to theWS2 by firmly tightening both captive screws.8 Snap on the cover plate with the arrow (on itsback side) pointing up.9 Save usage card for room occupants.Installation StepsBoth Wall and Junction Box MountingFigure 2: Remove plastictab to allow battery topower unitFigure 3: Press eachbutton to verify operationand that LEDs flash

Navigation menu