Enlighted SU4S Intelligent Light Sensor for Smart Networked Energy Saving Light Systems using 802.15.4 protocol stack and BLE for communications. User Manual PowerPoint Presentation

Enlighted, Inc. Intelligent Light Sensor for Smart Networked Energy Saving Light Systems using 802.15.4 protocol stack and BLE for communications. PowerPoint Presentation

Contents

Users Manual

Page 5 Page 6 93-01663-01 Rev01 Page 1Copyright © 2016 Enlighted Inc. All rights reserved.All other brand or product names are trademarks oftheir respective companies or organizations.TechnicalSupportFor questions regardingthe installation or operation ofthis product, contact EnlightedTechnical Support: support@enlightedinc.comCompany Contact InformationLocation: 930 Benecia Ave, Sunnyvale, CA 94085Phone: +1.650.964.1094 Web: enlightedinc.comFCC and Industry Canada Compliance InformationThis equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.This device complies with Part 15 of the FCC Rules and Industry Canada license-exempt RSS standard(s). Operation is subject to thefollowing two conditions:•this device may not cause harmful interference, AND•this device must accept any interference received, includinginterference that may cause undesired operation.Changes or modifications not expressly approved by Enlighted Inc.could void the user's authority to operate the equipment.Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitationest autorisée aux deux conditions suivantes:•l'appareil ne doit pas produire de brouillage, ET•l'utilisateur de l'appareil doit accepter tout brouillageradioélectrique subi, même si le brouillage est susceptible d'encompromettre le fonctionnement.CEThis device complies with the essential requirements and other relevant requirements of the R&TTE Directive (1999/5/EC). The equipment is Class 1 radio equipment which can be placed on the market and be put into service without restrictions in accordance with article 1(3) of Commission Decision 2000/299/EC (Version July 2014).Ruggedized Sensor(SU-4S)Installation InstructionsModel: SU-4SFCC ID: AQQ-SU4SIC: 10138A-SU4SRuggedized Sensor (front and back)Applicable For:SU-4S-LRW; SU-4S-LRBSU-4S-HRW; SU-4S-HRBShipped ComponentsEnlighted Ruggedized Sensor Unit½ inch Lock NutTools you may Need½ inch Knock out toolItems you will Need½ inch LB Conduit Body½ inch Chase Nipple
Page 2 Page 3 Page 4InstallationFigure 7 The Ruggedized sensor is shipped with the cable attached to the sensor. Figure 1.Figure 1 Figure 6 LED Status Description/SolutionLED not on Check power and wiringPurple solid All LEDs are on during boot time for 5-6 secondsGreen blinking Sensor commissioned and workingRed blinking Incompatibility between LED driver and sensor–Replace LED driver and if not resolved, replace sensor. Red solid Faulty sensor –replace sensorGreen solid Sensor installed, initialized, and uncommissioned –waiting for discovery.Blue solid Image being upgraded.LED DescriptionCautionInstallation and maintenance must be performed by a qualifiedelectrician in accordance with local, state, and national electrical codes (NEC) and requirements.Step 1: Turn off all power to the light fixture by switching off the circuit breaker.Step 2: Mount the Control Unit (CU) in a UL approved enclosure. Refer to the Control Unit Installation Guide. See Figure 7 for detailed wiring connections from the CU. Step 3: Remove the cover plate of the ½ inch LB conduit body by removing the two screws. Figure 2.Figure 2 Step 4: Thread the Ruggedized sensor onto LB conduit body. Figure 3.Figure 4 Step 6: Knock out a ½ inch hole on the end of the light fixture. Using the ½ inch chase nipple, connect the LB conduit to the fixture. See Figure 5.Step 5: Replace the cover and two screws on the LB conduit body. Figure 4.Figure 3Figure 5 Chase NippleStep 7: Pull the Ruggedized sensor cable through the chase nipple into the fixture and connect it to the Control Unit. See Figure 6. For wiring connections to the CU, see Figure 7.Step 8: If the ruggedized senor cable is not long enough to reach the Control Unit, use an RJ12 coupling to connect the rugged sensor cable to an Enlighted 7ft Sensor cable. (CBL-2-7F)Step 9: Switch on the circuit breaker to turn the power on.Enlighted Control UnitEnlighted Control Unit

Navigation menu