Enlighted SU4E Compact Sensor User Manual PowerPoint Presentation

Enlighted, Inc. Compact Sensor PowerPoint Presentation

User Guide

Page 5 Page 6 94-00552-02 Rev07 Page 1Technical SupportFor questions regarding the installation or operation of thisproduct, contact EnlightedTechnical Support: support@enlightedinc.comCompany Contact InformationLocation: 930 Benecia Ave, Sunnyvale, CA 94085Phone: +1.650.964.1094 Web: enlightedinc.comFCC and Industry Canada Compliance InformationThis equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.This device complies with Part 15 of the FCC Rules and Industry Canadalicense-exempt RSS standard(s). Operation is subject to the following two conditions:•this device may not cause harmful interference, AND•this device must accept any interference received, includinginterference that may cause undesired operation.Changes or modifications not expressly approved by Enlighted Inc.could void the user's authority to operate the equipment.Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes:•l'appareil ne doit pas produire de brouillage, ET•l'utilisateur de l'appareil doit accepter tout brouillage radioélectriquesubi, même si le brouillage est susceptible d'en compromettre lefonctionnement.CEThis device complies with the essential requirements and other relevant requirements of the R&TTE Directive (1999/5/EC). The equipment is Class 1 radio equipment which can be placed on the market and be put into service without restrictions in accordance with article 1(3) of Commission Decision 2000/299/EC (Version July 2014).Copyright © 2016 Enlighted Inc. All rights reserved.All other brand or product names are trademarks oftheir respective companies or organizations.6-wire Compact Sensor (SU-4E)Installation InstructionsModel: SU-4ENo: SU-4E-01FCC ID: AQQ-SU4E01IC: 10138A-SU4E01Figure 1: Compact Sensor Shipped Components•Enlighted Compact Sensor UnitTools you may Need•1” Drill bit•Hand drill
Page 2 Page 3 Page 4Step Description1. Switch off the circuit breaker supplying power to the light.2.Mount the Control Unit (CU) behind the ceiling tile or in a UL approved enclosure. Refer to the Control Unit Installation Guide.3.Connect theRJ-12 connector end of the Compact Sensor cable to the Control Unit. See Figure 5.4.Note: The sensor is designed to mount in a 15/16th inch hole in the ceiling tile. Make a small circular cut in the ceiling tile. 5.Pull the 6-pin end of the Compact Sensor cable through the hole in the tile. See Figure 2.6.Insert the end of the wire into the sensor’s 6-pin connector. See Figure 2.7.Push the spring arms together and insert the sensor through the hole in the tile. See Figure 2.8.Turn the power on by switching on the circuit breaker.Tile Mount Sensor InstallationFigure 2: Tile Mount SensorFixture Mount Sensor InstallationStep Description1. Switch off the circuit breaker supplying power to the light.2.Mount the Control Unit in the ballast cavity of the fixture or in a UL approved enclosure.3.Connect the RJ-12 connector end of the Compact Sensor cable to the Control Unit. See Figure 5.4.Note: The sensor is designed to mount in a ½ inch trade size knockout on a fixture. Determine the location for the sensor in the fixture and cut a ½ inch knockout in the fixture. See Figure 3. 5.Unthread the spring arms from the Compact Sensor. 6.Insert the Compact Sensor through the hole in the fixture. Use the spring arms from behind the sensor to fasten the Compact Sensor. See Figure 4.7.Insert the 6-pin end of the Compact Sensor cable to the 6-pin connector on the sensor.8.Turn the power on by switching on the circuit breaker.Caution•Installation and maintenance must be performed by a qualified electrician in accordance with local, state, andnational electrical codes (NEC) and requirements.Spring arms Push the spring arms together and insert the sensorFigure 5: Wiring ConnectionFigure 4: Fixture Mount SensorFigure 3: Sensor locationin a fixtureLED Status Description/SolutionLED not on Check power and wiringPurple solid All LEDs are on during boot time for 5-6 secondsGreen blinking Sensor commissioned and workingRed blinking Incompatibility between LED driver and sensor–Replace LED driver and if not resolved, replace sensor. Red solid Faulty sensor –replace sensorGreen solid Sensor installed, initialized, and uncommissioned –waiting for discovery.Blue solid Image being upgraded or BLE ResetLED Description

Navigation menu