Enlighted PC-01-20 Intelligent Energy Sensor for Smart Networked Energy Saving Lighting Systems User Manual PowerPoint Presentation

Enlighted, Inc. Intelligent Energy Sensor for Smart Networked Energy Saving Lighting Systems PowerPoint Presentation

Users Manual

Page 5 Page 6 Page 1Copyright © 2014 Enlighted Inc. All rights reserved.All other brand or product names are trademarks oftheir respective companies or organizations.TechnicalSupportFor questions regardingtheinstallation or operation ofthis product,contact EnlightedTechnicalSupport: support@enlightedinc.comCompany Contact InformationLocation: 930 Benecia Ave, Sunnyvale, CA 94085Phone: +1.650.964.1094 Web: enlightedinc.comCA Contractor’s License: CCL# 980903FCC and Industry Canada Compliance InformationThis equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.USAThis device complieswith Part 15 of the FCC Rules. Operation is subjectto the following two conditions:•this devicemay not cause harmful interference, AND•this device must accept anyinterference received, includinginterference that may cause undesiredoperation.Changes or modifications not expressly approved by Enlighted Inc.could void the user's authority to operate the equipment.CanadaThis device complies with Industry Canadalicense-exempt RSSstandard(s). Operation is subject to the followingtwo conditions:•this devicemay not cause harmful interference, AND•this device must accept anyinterference received, includinginterference that may cause undesiredoperation.Changes or modifications not expressly approved by Enlighted Inc.could void the user's authority to operate the equipment.Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.L'exploitationest autoriséeauxdeux conditions suivantes:•l'appareil ne doit pas produire de brouillage,ET•l'utilisateur de l'appareildoitaccepter tout brouillageradioélectriquesubi,même si le brouillage est susceptible d'encompromettre le fonctionnement.CEThis device complies with the essential requirements and other relevant requirements of the R&TTE Directive (1999/5/EC). The product is compliant with the following standards and/or other normative documents. EN 62479, ETSI EN 301, EN 300•The equipment is Class 1 radio equipment which can be placed on the market and be put into service without restrictions in accordance with article 1(3) of Commission Decision 2000/299/EC (Version July 2014).Figure 1: Plug Load Controller, Locknut, and StickerPlug Load ControllerModel PC-01-20Installation InstructionsShipped Components•Plug load controller (and ½ inch locknut)•MAC address stickerTools You May Need•Wire stripperSupplies You May Need•Wire nuts (or connectors)•Junction box (j-box)•2 Conductor plus ground 12 AWG solid wire cable•3Conductor plus ground 12 AWG solid wire cable •Clamps93-01142-01 Rev02Model: PC-01-20FCC ID: AQQ-PC-01-20 Industry Canada: 10138A-PC0120
TroubleshootingPage 2 Page 3 Page 4Cautionary Suggestions•Installation and maintenance must be performed byqualified electrician.•Installations and maintenance must be performed inaccordance with local, state, and national electrical codesand requirements.Problem SolutionLED is not on when the device is powered1) Check to see that power is present from the circuit panel.2) Check the wiring, if LED does not come on, then replace the device.Step DescriptionJ-box Install (see Figure 2)1Punch out a ½ inch knock out from the j-box and insert the threaded end of the plug load controller. Secure the plug load controller to the j-box with the supplied locknut.2(Main Feed) Feed the j-box with (3) 12 AWG conductors. (Hot, Neutral, and Ground)3Connect the j-box with (4) 12 AWG conductors that run from the j-box to the receptacle wall box.(Hot, Switched Hot, Neutral, and Ground)4Using wire nuts (or wire connectors):a) Connect the hot wire from the main feed to the black wire of the plug load controller.b) Connect the neutral wire from the main feed to the white wire of the plug load controller and the neutral wire that feeds through to the receptacle.c) Connect the red wire of the plug load controller to the switched hot wire that feeds through to the receptacle.d) Connect the blue wire of the plug load controller to the hot wire that feeds through to the receptacle.e) Connect all ground wires to the j-box. Receptacle Install (see Figure 4)5Break the connection on the “hot side” of the receptacle between the two outlets.6Connect the neutral wire to the neutral connection on the receptacle.7Connect the switched hot wire to the hot side of the “controlled outlet”.8Connect the hot wire to the hot connection of the “uncontrolled outlet” (always powered).Installation StepsInstallation Steps (Continued)Step Description9Install the receptacle in the wall box10 Attach a receptacle faceplate that distinguishes the controlled outlet.11 Attach the included MAC address sticker on the faceplate. Figure 2: J-box with plug load controller, showing main feed and wiring to receptacle.Figure 3: Wiring Diagram Figure 4: Receptacle wiringMain feed:•Hot•Neutral•GroundReceptacle feed:•Hot•Switched Hot•Neutral•GroundHotNeutralSwitchedHotGround

Navigation menu