Enlighted CS-D2 Intelligent Light Sensor for Smart Networked Energy Saving Lighting Systems. User Manual PowerPoint Presentation

Enlighted, Inc. Intelligent Light Sensor for Smart Networked Energy Saving Lighting Systems. PowerPoint Presentation

Contents

Users Manual 1 v2

Page 5 Page 6 93-01182-02 Rev04 082115 Page 1Copyright © 2015 Enlighted Inc. All rights reserved.All other brand or product names are trademarks oftheir respective companies or organizations.TechnicalSupportFor questions regardingtheinstallation or operation ofthis product,contact EnlightedTechnicalSupport: support@enlightedinc.comCompany Contact InformationLocation: 930 Benecia Ave, Sunnyvale, CA 94085Phone: +1.650.964.1094 Web: enlightedinc.comFCC and Industry Canada Compliance InformationThis equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.This device complieswith Part 15 of the FCC Rules and Industry Canadalicense-exempt RSS standard(s). Operation is subjectto thefollowing two conditions:•this devicemay not cause harmful interference, AND•this device must accept anyinterference received, includinginterference that may cause undesiredoperation.Changes or modifications not expressly approved by Enlighted Inc.could void the user'sauthority to operate the equipment.Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.L'exploitationest autoriséeauxdeux conditions suivantes:•l'appareil ne doit pas produire de brouillage,ET•l'utilisateur de l'appareildoitaccepter tout brouillageradioélectriquesubi, même si le brouillage est susceptible d'encompromettre le fonctionnement.CEThis device complies with the essential requirements and other relevant requirements of the R&TTE Directive (1999/5/EC). The equipment is Class 1 radio equipment which can be placed on the market and be put into service without restrictions in accordance with article 1(3) of Commission Decision 2000/299/EC (Version July 2014).Compact Sensor (CS-D2)Installation InstructionsModel: CS-D2 FCC ID: AQQ-CS-D2IC: 10138A-CSD2Figure 1: Compact Sensor (CS-D2) Shipped Components•Enlighted Compact Sensor UnitItems you may Need•Lock Nut for fixture mounting or•Spring Arms for Tile mounting•18 AWG solid copper wire, rated >=300vTools you may Need•1” Drill bit•Hand drill•Wire stripper
Page 2 Page 3 Page 4Step Description1. Switch off the circuit breaker supplying power to the light.2The sensor is designed to mount in a 1-inch hole in the ceiling tile. This sensor is for use with the Philips XSR driver.3. Make a small circular cut (one-inch) in the ceiling tile. Thread the spring arms around the sensor. 4. Measure the distance between the sensor’s installation location and the LED driver’s “SR connections,”. Cut two lengths of 18 AWG solid wire that are at least this length plus one inch. Strip each end of the two wires leaving 3/8 inch of exposed wire. 5. Insert one end of the pair of wires into the LED driver’s “SR connections” wire holes, (see Figure 5), and pull the other end through the hole in the tile. See Figure 2.6. Insert the free end of the pair of wires into the sensor’s wire hole. See Figure 2.7. Push the spring arms together and insert the sensor through the hole in the tile. See Figure 2.8. Turn the power on by switching on the circuit breaker.Tile Mount Sensor InstallationProblem SolutionLED not on Check power and wiringSolid red LED Sensor fault –replaceRed blinking LED Incompatibility between LED driver and sensor –replace LED driver and if not resolved, replace sensorTroubleshootingNote: For any reason, if you need to remove the two wires, push down on the tabs located on the rear of the sensor with a pointed device, and remove the wires while continuing to hold the tab down.To Enlighted sensorFigure 2: Tile Mount Sensor Figure 3: Sensor location in a fixtureFixture Mount Sensor InstallationStep Description1. Switch off the circuit breaker supplying power to the light.The sensor is designed to mount in a ½ inch trade size knockout on a fixture. This sensor is for use with the Philips XSR driver.2Determine the location for the sensor in the fixture and cut an existing knockout (½ inch) in the fixture. See Figure 3. 3Insert the compact sensor through the hole in the fixture. Use the lock nut from behind the sensor to fasten the compact sensor. See Figure 4.4. Measure the distance between the sensor’s installation location and the LED driver’s “SR connections,” and cut two lengths of 18 AWG solid wire that are at least thislength plus one inch.5. Strip each end of the two wires leaving 3/8 inch of exposed wire.6. Insert one end of the pair of wires in the sensor’s wire holes and the other end in the LED driver’s “SR connections” wire holes. See Figure 6.7. Turn the power on by switching on the circuit breaker.Caution•Installation and maintenance must be performed by a qualified electrician inaccordance with local, state, andnationalelectrical codes (NEC) and requirements.Spring armsTo lampsPush the spring arms together and insert the sensorLocknutFigure 5: Wiring ConnectionFigure 4: Fixture Mount Sensor

Navigation menu