EnGenius Technologies ESR1750 Dual Band Wireless AC1750 Router User Manual

EnGenius Technologies Dual Band Wireless AC1750 Router

User Manual.pdf

1quantum beamUser ManualDual Band Wireless ACI750 Router with Gigabit Ports and USBESR1750version 1.0
2IMPORTANTTo install this router, please refer to the Quick Start Guide included in the product packaging.To activate and use EnShare™ refer to the document “Using EnShare” also in the product packaging.
3Chapter 1 Product Overview..............................................................5 Key Features....................................................................................................6 Technical Specications/Software Features...................................8 Physical Interface..........................................................................................9Chapter 2 Controlling the Router Through Its Web Conguration Interface...........................................................10 Logging In.....................................................................................................11 ViewingtheWebCongurationDashBoard..................................12 Home Page...................................................................................................13 WebMenusOverview...............................................................................14 Internet.................................................................................................15 Wireless2.4GHz..........................................................................................16 Wireless5GHz...............................................................................................17 Parental Controls.......................................................................................18 GuestNetwork.............................................................................................19 IPv6.....................................................................................20 Firewall...................................................................................21 VPN.....................................................................................22 USBPort..........................................................................................................23 Advanced.......................................................................................................24 Tools................................................................................................................26Chapter 3 Installation Setup Wizard..............................................27 InternetSetupWizard...............................................................................28 SettingUpYourInternetConnection.................................................29 SettingYourWirelessSecurity..............................................................30 SettingyourRouter’sAdministratorPassword.............................31 Setting your Router’s Time Zone........................................................32 StatusandSaveSettings.......................................................................34Chapter 4 Basic Network Settings.................................................35 NetworkSettings.......................................................................................36 Status.............................................................................................................37 WANSettings...............................................................................................38 LANSettings................................................................................................39 WLANSettings............................................................................................40 GuestNetwork............................................................................................41 ConguringtheLAN(LocalAreaNetwork).....................................42 DHCPServer.................................................................................................43 ConguringDynamicHostCongurationProtocol.......................44 EnableStaticDHCPIP..............................................................................45 CurrentStaticDHCPTable......................................................................46 ConguringEventLogging.....................................................................47 MonitoringBandwidthUsage................................................................48 ConguringtheSystemLanguage.....................................................49 ConguringIPCameras............................................................................50 ConguringInternetSettings...............................................................51 ConguringDynamicIP...........................................................................52 DNSServers..................................................................................................53 ConguringStaticIP.................................................................................54 ConguringPPPoE.....................................................................................55 ConguringPPTP.......................................................................................56 PPTPSettings..............................................................................................57 Conguring L2TP.......................................................................................58 L2TP Settings..............................................................................................59 ConguringDS-Lite...................................................................................60 WirelessLANSetup...................................................................................61 AccessPointMode....................................................................................62 WirelessDistributionSystemMode....................................................63 WDSSecuritySettingsScreen...............................................................64Table of Contents
4Chapter 5 Wireless Encryption.....................................................65 Wi-FiProtectAccess(WPA)Pre-SharedKey..................................66 ConguringSecurity.................................................................................67 Encryption Type.........................................................................................68 WPA Radius..................................................................................................69 WiredEquivalentPrivacy(WEP)...........................................................70 ConguringFilters......................................................................................71 MACAddressFilteringTable.................................................................72 ConguringWi-FiProtected Setup....................................................73 ConguringClientList.............................................................................74Chapter 6 Advanced Settings...........................................................75 ConguringAdvancedSettings............................................................76 SettingUpParentalControls.................................................................78 AddingaControlPolicy............................................................................79 ViewingParentalPolicies.......................................................................82 GuestNetwork............................................................................................83 ConguringtheDHCPServerSetting...............................................84 ViewingtheDHCPClientListontheGuestNetwork.................85 IPv6.................................................................................................................86 ViewingtheIPv6ConnectionStatus.................................................87 ConguringStaticIPv6............................................................................88 Setting Autoconguration.....................................................................89 Conguring PPPoE....................................................................................90 Conguring6to4........................................................................................92 ViewinglocalConnections.....................................................................93 Firewall Setup.............................................................................................94 ConguringAdvancedSettings...........................................................95 ConguringDemilitarizedZone...........................................................97 ConguringDenialofService................................................................98 VirtualPrivateNetworkSetup..............................................................99 ConguringaVPNTunnelProle.......................................................100 General........................................................................................................101 SA(SecurityAssociation)......................................................................102 Network.......................................................................................................103 Advanced.....................................................................................................104 ConguringaUserSetting...................................................................105 USBPort/Enshare..................................................................................106 ViewingFileServer.................................................................................107 ViewingDLNA...........................................................................................108 AdvancedNetworkSettings................................................................109 PortMappingSetup................................................................................110 CurrentPortMappingTable................................................................111 PortForwardingSetup...........................................................................112 CurrentPortForwardingTable..........................................................113 PortTriggeringSetup............................................................................114 ApplicationLayerGetawaySetup....................................................116 UniversalPlugandPlaySetup...........................................................117 InternetGroupMulticastProtocolSetup.......................................118 Quality of Service Setup.......................................................................119 Priority Queue...........................................................................................120 BandwidthAllocation.............................................................................121 Routing Setup...........................................................................................122 WakeonLANSetup................................................................................123 ToolsSetup................................................................................................124 System Time Setting..............................................................................125 SynchronizingTimewithaComputer.............................................126 DynamicDomainNameService(DDNS)Setup............................127 DiagnoseThatClientDevicesAreConnected.............................128 UpgradingtheRouter’sFirmware....................................................129 BackingUptheRouter’sSettings.....................................................130 RebootingtheRouter............................................................................131Appendix..........................................................................................132 WallMountingtheRouter....................................................................133 FCCInterferenceStatement...............................................................134 IndustryCanadaStatement................................................................135 Europe–EUDeclarationofConformity.........................................136
5Chapter1 Product Overview
6MaximumdataratesarebasedondraftIEEE802.11acandIEEE802.11standards.Actualthroughputandrangemayvarydependingonmanyfactorsincludingenvironmentalconditions,distancebetweendevices,radiointerferenceintheoperatingenvironment,andmixofdevicesinthenetwork.EnGeniusTechnologies,Inc.EnShare™supportsbothFAT32andNTFSUSBformats.Transferspeedsofdatafromyourrouter-attachedUSBstoragedevicetoaremote/mobiledevicemayvarybasedonInternetuplinkanddownlinkspeeds,bandwidthtrafcateithersendorreceivelocations,thedataretrievalperformanceoftheattachedstoragedeviceorotherfactors.EnGeniusdoesnotguaranteecompatibilitywithallUSBdrives.EnGeniusdoesnotwarrantitsproductsorEnSharefromlossofdataorlossofproductivitytime.Featuresandspecicationssubjecttochangewithoutnotice.Trademarksandregisteredtrademarksarethepropertyoftheirrespectiveowners.ForUnitedStatesofAmerica:Copyright©2013EnGeniusTechnologies,Inc.Allrightsreserved.Product OverviewKey Features• DualBandWirelessAC1750DraftIEEE802.11acandIEEE802.11a/b/g/n• Upto450Mbpsinthe2.4GHzfrequencybandandupto1300Mbps in5GHz• Built-in4-PortGigabitSwitchforoptimalaudio/visualstreaming• USBPorttoshareandaccessmediacontentinthehomeorwhenyou’reawayfromhomewithEnShare™• NextGenerationIPv6Compliant• ParentalControls• Upto8GuestAccesssettings(4perfrequencyband)• Industry-standardWirelessEncryptionandSecurity• VPNServerSupportLite-BusinessApplications• EasySetupWizardRobust and Reliable Wireless PerformanceTheESR1750isaDual-BandWirelessAC1750Routerwithabuilt-in4-portGigabitEthernetswitch.ThiscosteffectiveroutercanconnecttoDSLorcablemodemstoprovidehigh performance Internet access for desktop or laptop computers,tablets,smartphonesandawidevarietyofhomeentertainmentdevices,likeHDTVs,settopboxes,Blu-rayplayers and game consoles. Therouter’sconcurrentdualbanddesignenablesuserstoconnectnumerouswirelessdevicestoit,givingthemtheoptiontoleverageQuantumBeamandtheACspeedboostonthelesscongested5GHzfrequencyforbandwidthintensiveapplicationslikestreamingHDvideo.
7Product OverviewA Media Sharing PlatformTheESR1750isdesignedtoaccessandsharemediafordevicesonthehomenetwork.InadditiontoconnectinghomeentertainmentcomponentstoanyofitsavailableGigabitEthernetports,theESR1750alsoincludesaUSBportforattachingaUSBstoragedevicesowirelessdevicesinthehomeorawayfromthehomecanaccessoruploadmediacontentwhereverthereisanavailableInternetconnectionthroughEnShare™-YourPersonalCloud.EnShareisavailableasanInternetportalforaccessingstoredmediaconnectedtotheUSBportoftherouter(SeetheUsingEnSharedocumentintheproductpackaging).EnSharewillalsobeavailableasanappforAppleiOSdevices(iPads,iPodsandiPhones)andAndroid-baseddevices(smartphones,tabletPCs,Kindleandothermobilereaders)soon.TheappswillbeavailablethroughAppleiTunesStoreandGooglePlayrespectively.Industry-standard Wireless SecurityThe router supports a variety of security features and mechanismsincludingindustry-standardWPA/WPA2wirelessencryptiontopreventunauthorizedaccesstoyournetwork.Italsoincludesabuilt-inSPI(StatefulPacketInspection)rewalltohelppreventattacksfrommalicioussoftware(malware)from the Internet. The router also supports IPv6.Attach USB storage to the ESR1750 and access or upload video, music, and other media throughout your home or away from home from your smartphone, tablet, or laptop.USBMediaAnywhere with EnShareTMMore Guest Access OptionsTheESR1750alsoincludesuptoeight(8)separateanddiscreteGuestAccessoptionsallowingtherouter’sadministratortoassigndifferentnames(SSIDs-ServiceSetIdentiers)foreachlogintothehomenetworksofriendsorvisitorscanaccesstheuser’sInternetconnectionwithoutaccessingpersonaldatastoredonnetworkedcomputersinthe home.
8Technical SpecicationsDevice InterfaceGigabitWANPort4GigabitLANPortsUSB2.0PortPushButtonforWPSResetButtonIEEE Standards802.11ac(draft)802.11a/b/g/nUpto450Mbpswirelessspeedon2.4GHzfrequencybandand1300Mbpson5GHzfrequencyband802.3i/u/abLED IndicatorsPowerWLAN(WirelessConnection)InternetPackage ContentsESR1750RouterPowerAdapter(12V1.5A)QuickStartGuideRJ45EthernetCablePower SpecicationExternalPowerAdapterDCIn,12V1.5ACerticationsFCC/CE/ICPhysical/Environmental ConditionsOperatingTemperature:0º~40ºCelsiusHumidity:90%orless(non-condensing)StorageTemperature:-20º~60ºCelsiusHumidity:95%orless(non-condensing)Software FeaturesOperating ModeAPRouter/WDSWireless FeaturesAutoChannelSelectionOutputPowerControlWMM(WirelessMultimedia)MSSID(MultipleSSID)SecurityWEP/WPA-PSK/WPA2-PSKTKIP/AESHiddenSSIDMACAddressFiltering802.1XAuthenticationDDoSDHCPServer/ClientSPI(StatefulPacketInspection)NATPortForwardingDMZPortMapping/TriggeringVPNServer(PPTP/L2TP)VPNClient(PPTP/L2TP)VPNPass-through(PPTP/L2TP/IPSec)RuleBased(IPAddressRanges,PortBlockICMPVPNTunnel(Maximum5)QoSIP FilteringPort FilteringDDNSIPv6Pass-throughMACCloneTrafcMonitorWANType:PPPoE/DHCP/StaticIPUSBFeatures:SAMBA
9Physical InterfaceDimensions and WeightsWeight:0.5lbs.Diameter:6.36”Height:1.64”1 WLAN 5 GHz LED2 WLAN 2.4 GHz LED3 Power LED4WAN Port/(Internet) Status LED5 WPS(WirelessProtectedSetup)LED6 DC Power Jack—connectstheESRSeriesRoutertoitsDCpoweradapter7 WAN Port—connectstheESRRoutertoacableorDSLmodemtoaccesstheuser’sbroadband(Internet)connection8 LAN Ports (1 – 4) — for connecting home entertainment components,computersorotherEthernet-enableddevicesusingEthernetcables9 Reset Button — For resetting the router to its factory default settingsbypressingbuttonformorethan11secondsoruntilthePowerLEDstartsashing.10 USB PortforconnectingaUSBStorageDevice11 WPS Button—Wi-FiProtectedSetupbutton.ToassociateanotherWPS-enabledclientdevice(computer,wirelessmediabridge,USBadapter,etc.)presstheWPSbuttonfor2to5secondsontherouterwhilealsopressingtheWPSbuttononthe end device.Whenconsideringtheplacementoftherouterrememberthefollowing:• Itmustbeclosetoanelectricaloutlet.• Foroptimalwirelessconnectivity,place the router near the center of theroomifpossible,atahighlevelOtherelectronicdevicesandsomearchitectural construction materials orimpedimentsmayinterferewiththewirelesssignal(s)oftherouterand reduce its range or coverage. Try tominimizethenumberofwallsoroorsthattherouter’ssignalneedstopenetratetoconnecttootherwirelessdevices.
10Chapter2 Controlling the Router Through Its Web Conguration Interface
11Logging InDuringtheQuick Start Guide procedure, you should have successfully logged into the router’s Web Conguration user interface (essentiallytherouter’soperatingsystemthatcontrolshowitoperates)andestablishedsomeinitialsettingsand controls for the router. Ifyouwishtochangetherouter’ssettings (establishanewusernameandpasswordforthepersonwhomanagesandmaintainstherouter,setParentalControls,establishaGuestAccess-SSIDsettingforvisitors,oranynumberofothersettings)youcanlogintotheWebCongurationagainthroughthewebbrowser(InternetExplorer,Safari,Chrome,Firefox)onyourcomputerortabletdevice.To do this, enter the router’s default IP address of 192.168.0.1intoyourbrowser’saddresswindow.1.Attheloginscreenenteryourusernameandapassword2.ClickLogintocontinue.Thedefaultloginsettingsare: username:admin password:adminIt’s highly recommended that, if you haven’t done so already, to change these default names, so your router and the devices connectedtoitonyourhomenetworkaremoresecure.
12Viewing the Web Conguration Dash BoardTheHomePagescreenoftheWebCongurationinterface,ordashboard,providesaccesstotherouter’ssettingsandcontrols.Home PageHomeSetupWizardNetworkSettingsUSBStorageSharingIPCamViewerLanguageLogout
13Home PageThe Home PagedisplaystheareaswithintheWebCongurationtowhichyoucannavigate:Setup Wizard, Network Settings, USB Storage Sharing, IP Cam Viewer, Language, and LogoutHomeTheHomelinktakesyoubacktothedashboardscreennomatterwhereyouareintheWebCongurationinterface.Setup WizardTheSetupWizardlinkstartsthewizardthatautomaticallycongurestherouter.Network SettingsTheNetworkSettingslinkdisplaysthemenustomanuallyconguretherouter.USB Storage SharingTheUSBStorageSharinglinkdisplaysthemenustoaccessshared storage devices connected to the router.IP Cam ViewerTheIPCamViewerlinkdisplaysthemenustoviewanIPcameraconnectedtothenetwork.LanguageTheLanguagelinkdisplaysthemenutosettheOSDlanguage.LogoutTheLogoutlinkclosestherouter’sWebCongurationinterface from any screen.
14Web Menus OverviewSystemViewandeditsettingsthataffectsystemfunctionality.Operation ModeCongurethedevicetobearouterorWDSaccesspoint.StatusDisplaysthesummaryofthecurrentsystemstatus.ScheduleScheduleservicestostartandstopatspecictimesorintervals.Event LogViewrecordedsystemoperationsandnetworkactivityevents.MonitorViewthecurrentnetworktrafcbandwidthusage.LanguageConguretheapplicationmenuandGUIlanguage.IP CameraViewtheIPcamerasconnectedtotheESRSeriesRouter.
15InternetViewandeditsettingsthataffectnetworkconnectivity.StatusDisplaysasummaryoftheInternetstatusandtypeofconnection.Dynamic IPSetupadynamicIPconnectiontoanISP(InternetServiceProvider).Static IPSetup a static IP connection to an ISP.PPPoESetup a PPPoE connection to an ISP.PPTPSetup a PPTP connection to an ISP.L2TPSetup an L2TP connection to an ISP.
16Wireless 2.4 GHzViewandeditsettingsfor2.4GHzwirelessnetworkconnectivity.StatusViewthecurrentwirelessconnectionstatusandrelatedinformation.BasicConguretheminimumsettingsrequiredtosetupawirelessnetworkconnection.AdvancedConguretheadvancednetworksettings.SecurityCongurethewirelessnetworksecuritysettings.FilterEstablishalistofclientdevices(computer,tablets,smartphones,printers,etc.)basedontheirMAC(MediaAccessControl)numbersthatareallowedtowirelesslyconnecttothe2.4GHznetwork.WPSAutomatestheconnectionbetweenawirelessdeviceandyourencryptedrouterusingan8-digitPIN.Client ListViewthe2.4GHzwirelessdevicescurrentlyconnectedtothenetwork.
17Wireless 5 GHzViewandeditsettingsfor5GHzwirelessnetworkconnectivity.StatusViewthecurrentwirelessconnectionstatusandrelatedinformation.BasicConguretheminimumsettingsrequiredtosetupawirelessnetworkconnection.AdvancedConguretheadvancednetworksettings.SecurityCongurethewirelessnetworksecuritysettings.FilterEstablishalistofclientdevices(computer,tablets,smartphones,printers,etc.)basedontheirMAC(MediaAccessControl)numbersthatareallowedtowirelesslyconnecttothe5GHznetwork.WPSAutomatestheconnectionbetweenawirelessdeviceandyourencryptedrouterusingan8-digitPIN.Client ListViewthe5GHzwirelessdevicescurrentlyconnectedtothenetwork.
18Parental ControlsViewandeditsettingsforparentalcontrols.WizardEnableordisabletheParentalControlsfunction.Themenualsoprovidesinforma-tionforconguringparentalcontrolpolicies.Web MonitorThemenuprovidesalogoftheeventsfordenedparentalcontrolpolicies.
19Guest NetworkViewandeditsettingsforaguestnetwork.SelectionEnableordisabletheGuestNetworkfunction.DHCP Server SettingConguretheGuestNetworkDHCPserversettings.DHCP Client ListConguretheGuestNetworkclientlist.
20IPv6ViewandeditsettingsfortheIPv6protocol.BasicAllowsyoutoenableordisabletheIPv6andIPv6Pass-throughfunctions.StatusShowsIPv6LANconnectiondetails.Static IPv6ConguretheIPv6protocol.Auto CongurationConguretheIPv6byobtainingtheinformationthroughtheISPprovider.PPPoECongurethePPPoEnetworkprotocol,obtaininformationfromyourISP(InternetServiceProvider).6to4AllowsIPv6packetstobetransmittedoveranIPv4network.Link LocalConguretheIPv6linklocaladdress.
21FirewallViewandeditsettingsforthenetworkrewall.BasicEnableordisablethenetworkrewall.AdvancedCongurevirtualprivatenetwork(VPN)packets.DMZRedirectpacketsfromtheWANportIPaddresstoaparticularIPaddressontheLAN.DoSEnableordisableblockingofDoS(DenialofService)attacks.ACLCongureaccesscontrollists.
22VPNViewandeditsettingsforVPNtunnelling.StatusViewthestatusofcurrentVPNtunnels.Prole SettingManuallycongureVPNtunnels.User SettingCongureusers,userIDandpasswordcombinations,andassignaccesstospecicVPNtunnels.WizardAutomaticallycongureVPNtunnelswithguidancefromthesoftware.
23USB PortForviewingandeditingsettingsforstoragesharing.EnShare™EnablesordisablestheEnShareremoteaccessfunction.File SharingEnablesordisablestheSambasharingfunction.File ServerEnablesandcongurestheFileServerfunction.DLNAEnablesthediscoveryofDLNAdevices(someHDTVs,gameconsoles,somesettopboxes/mediaplayers,Blu-rayplayers,somesmartphones,andnetworkattachedstorage)onthehomenetwork.
24AdvancedViewandcongureadvancedsystemandnetworksettings.NATEnableordisableNetworkAddressTranslation(NAT).Port MappingRe-directarangeofserviceportnumberstoaspeciedLANIPaddress.Port ForwardingCongureserverapplicationstosendandreceivedatafromspecicportsonthenetwork.Port TriggeringCongureapplicationsthatrequiremultipleconnectionsanddifferentinboundandoutboundconnections.ALGConguretheapplicationlayergateway(ALG).UPnPEnableordisableUniversalPlugandPlay(UPnP)functionality.IGMPEnableordisabletheInternetGroupMulticastProtocol(IGMP).
25QoSConguresthenetworkqualityofservice(QoS)settingbyprioritizingtheuplinkanddownlinkbandwidth.RoutingCongurestaticrouting.WOL(WakeOnLAN)CongureWakeonLANtoturnonacomputeroverthenetwork.
26ToolsForviewingandconguringtherouter’soperatingsystemandnetworktoolssettings.AdminForsettingtheadministrator’spasswordusedtologintotherouter.TimeForconguringthesystemtimeontherouter.DDNSMapsastaticdomainnametoadynamicIPaddress.DiagnosisToperformaPingtesttoverifywhetheraspecicdeviceisconnectedtotheLAN.FirmwareForupdatingtherouter’srmware.BackupForloadingorsavingthecongurationsettingstoorfromabackupleortorestore the router to its factory default settings.ResetRebootstherouter.
27Chapter3 Installation Setup Wizard
28Internet Setup WizardUsetheWizardtodetectandsetupthetype of Internet connection you need, tosetupasecurewirelessconnection,tocreateanadministratorpasswordtosecure the device, or set the router’s date and time properties.TousetheInternetSetupWizard,followthesesteps:1. Click the Wizard buttontoshowtheWizardstartscreen.2.ClickNexttocontinuewiththesetupprocedure.HomeSetupWizard
291.DecidehowtosetuptheInternetconnection.Note:It is recommended to let the device setup the Internetconnection automatically.• Select Auto DetecttolettheWizardsetuptheInternetconnection.• Select Manual Setup to set the properties yourself.2.ClickNext to continue or Prev to return to the previous screen.If you selected Manual Setup,followthesesteps:3. Select the Internet connection type and enter the connection properties.Setting Up Your Internet ConnectionNote:TheconnectiontypesavailablearestaticIP,PPPoE,DynamicIP,PPTP,andL2TP.4.ClickNext to continue, Prev to return to the previousscreen, or Cancel to stop the procedure.
30Settingwirelessencryptionfor2.4GHzand5GHznetworks.ToencryptthewirelesssignalsforeitherorbothofthefrequencybandsintheESR1750router,followthesesteps:1.EntertherouternameinthewirelessName(SSID)texteld.2.SelectthesecuritylevelfromtheEncryptiondropdownlist.3.EnterapasswordintheEncryptionKeytexteld.4.Repeatsteps1through3toencryptthe5GHzband5.ClickNext to continue, Prev to return to the previous screen, or Cancel to stop the procedure.Setting Your Wireless SecurityImportant:Toensurethenetworkissecure,itisrecommended to select High for an encryption level.
31Setting Your Router’s Administrator PasswordSetupapasswordtologintotheESRSeriesRouter.1.EnterapasswordintheNew Passwordtexteld.2.EnterthesamepasswordintheRepeat New Passwordtexteld.3.ClickPrev to return to the previous screen, Skip to skip this procedure, Next to continue, or Cancel to stop the procedure.
32Setting Your Router’s Time ZoneSetupdateandtimesyncronizationontheESRSeriesRouterwithacomputeroranNetworkTimeProtocol(NTP)server.Tosynchronizedateandtimesettingswithacomputer,followthesesteps:1.SelectSynchronizewithPC(computer)fromtheTime Setup dropdownlist.ThedateandtimevaluesareshowninthePC Date and Timetexteld.2.ClickPrev to return to the previous screen, Apply to save the settings, or Cancel to stop the procedure.TosynchronizethedateandtimesettingswithanNTPserver,followthesesteps:1. Select SynchronizewithNTPServerfromtheTime Setup dropdownlist.2.SelectatimezonevaluefromtheTime Zonedropdownlist.3.EnteranIPaddressordomainnameofanNTPserverintheNTP Servertexteld.4.ClicktheEnable Daylight Savingscheckboxtoenableordisabledaylightsavingstime.5.Selectthedateandtimevalueswhendaylightssavingstime starts in the Start Timedropdownlists.
336.Selectthedateandtimevalueswhendaylightssavingstime ends in the End Timedropdownlists.7.ClickPrev to return to the previous screen, Apply tosave the settings, or Cancel to stop the procedure.
34Status and Save SettingsThisscreenletsyoureview,changeandsaveyourInternetconnection,savewirelesssecuritysettingsorsetupupauser-speciednameforthedefaultEnGeniusDDNSservice.Toreviewormodifythedevicesettings,followthesesteps:1.ReviewthesettingsshownonthescreenfortheInternetconnection,2.4GHzand5GHznetworks,andtherouteradministrator login.2. You can change settings to the Internet connection and wirelessnetworksettingsbyclickingtheSetupbutton.Youmaywishtouseadifferentnamethat’seasiertorememberforthedefaultEnGeniusDDNSserviceusedfortheEnShare™ feature.TospecifyyourownDDNSname,followthesesteps:3. The Enableoptionshouldbeselectedbydefault.a. Enter the name in the Domain Nametexteld.b.SelectatimeintervaltorefreshtheDNSrecordsfromtheRefreshdropdownlist.c.ClickApplytosavetheDDNSnameyouhaveentered.4.ClickSavetoexittheWebCongurationinterface.Therouterwillreboot(restart)toapplyallthesettingsyou’vespecied.DevicesconnectedtotherouterwilltemporarilylosetheirInternetconnection.TherebootmaytakeseveralsecondsbeforetherouterandyourInternetconnectionareonceagainavailable.WARNING! Selecting DisableintheDDNSSettings/Statuseldwilldisconnecttherouter’sconnectiontothedefaultEnGeniusDDNSserverandasaresultwilldisabletheEnSharefeaturewhichletsyouaccessmediafromaUSBstoragedeviceconnectedtoyourESRpodrouterwhenyou’reawayfromyourhome.
35Chapter4 Basic Network Settings
36Note:If a feature or function does not apply to all modes, a note indicates whichmodesareapplicable.Otherwise,itisassumedthefeatureor function applies to all modes.Network SettingsViewing System StatusToseeamoredetailedviewoftherouter’sstatusthantheinformationdisplayedontheHomepageoftheWebCongurationinterface,fromtheHomePageclickonNetwork Settings buttonintheuppernavigationbar.HomeNetworkSettings
37StatusToviewtheStatussettings,clickSystem then click Status.OntheStatuspage,youcanviewasummaryofthecurrentroutersystemstatusincludingtherouter’s(hardware/softwareversion,date/time),wirednetwork(LAN)andwirelessnetwork(WLAN)information.ModelThe model name of the ESR Series Router.ModeThe operating mode of the ESR Series Router.UptimeTheamountoftimetheESRSeriesRouterhasbeenconnectedfor the current session.Current Date/TimeThe current system date and time. Hardware VersionThehardwareversionnumberoftherouter.Serial NumberTheserialnumberoftherouter(requiredforcustomerserviceorsupport).Application VersionTheversionoftherouter’srmware.Note:Toupdatetherouter’srmware,visitwww.engeniustech.com and go to the product page for your router, then select the Downloadstabatthebottomofthewebpagetoseeifanewerversionofthermwareisavailable.
38WAN SettingsAttain IP ProtocolDisplaystheIPprotocolinusefortherouter.Itcanbeadynamic or static IP address.IP AddressTherouter’sIPaddressasdesignatedbyanISP(InternetServiceProvider).Subnet MaskTherouter’sWANsubnetmaskasdesignatedbyanISPprovider.Default GatewayTherouter’sgatewayaddressasdesignatedbyanISPprovider.MAC AddressTherouter’sWANMAC(MediaAddressControl)address.Therouter’sMACaddressislocatedonthelabelonthebottompaneloftherouterandisuniqueforeachrouter.Primary DNSTheprimaryDNSofanISPprovider.Secondary DNSThesecondaryDNSofanISPprovider.
39LAN SettingsIP AddressTherouter’slocalIPaddress.ThedefaultLANIPaddressishttp://192.168.0.1ToaccesstheWebCongurationinterfacefortherouter,typethisaddressintotheaddress(URL)eldofyourwebbrowser.Thiscanonlybedoneinthesamephysicallocationwheretherouterresides(yourhomenetwork).Subnet MaskTherouter’slocalSubnetMask.DHCP ServerTheDHCPsettingstatus(Default:Enabled).TheDHCP(DynamicHostControlProtocol)isasoftwaremechanisminyourrouterthatassignsIPaddressestowiredandwirelessdevicesonyournetwork,forexample,acomputer,printer,tabletorHDTVonyournetworkmaybeassignedanIPaddressofhttp://192.168.0.104.Notehowtheaddressisessentiallyanextensionoradditionofyour router’s IP address.MAC AddressTherouter’suniqueMACaddress.
40WLAN SettingsChannelThecommunicationschannelusedbyallstations,orcomputingdevices,onthenetwork.ESSIDTheIDvalueofasetofoneormoreinterconnectedbasicservicesets(BSSs).SecurityThesecuritysettingstatus(Default:Disabled).BSSIDTheuniqueIDoftheBSSusingtheabovechannelvalueonthisrouter.TheIDistheMACaddressoftheBSSsaccesspoint.Associated ClientsThenumberofclientsassociated(activelylinkedtotherouterviaawirelessorwired/Ethernetconnection)withthisSSID.
41Guest NetworkGuest NetworkTheguestnetworkstatus.(Default:Disabled)IP AddressTheGuestNetwork’sLANIPaddress.Subnet MaskTheGuestNetwork’slocalsubnetmask.DHCP ServerTheGuestNetworkDHCPsettingstatus(Default:Enabled).Guest Network InterfaceTheSSID(ServiceSetIdentier)oftheGuestNetwork.
42Conguring the LAN (Local Area Network)Thesettingsonthispageallowyoutocongurethewirednetworksettings.Devicesconnectedtotherouter’sEthernetportscompriseitsLAN.Therouter’sIPisdenedintheIP Addresseld.ThedefaultsettingoftheDHCPserverissetto Enabledsothatnetworkedclients(computers,homeentertainmentcomponents,printers,etc.)willautomaticallybeassignedIPaddressesbytherouter.MoreadvancedusersmaywishtoconguretheDNSserversettingstomeettheirspecicrequirements.Changingthesettings in this section are not necessary for most situations.ToviewtheLANsettings,clickSystem, then click LAN.Note: Keep the router’s default values if you are uncertain of the settings values.LAN IP IP AddressForconguringtherouter’sLANIPaddress.IP Subnet MaskForconguringtherouter’sLANSubnetMask802.1d Spanning TreeSpanningTreeisdisabledbydefault.Whenenabled,SpanningTreepreventsnetworkloops(transmissionswon’tpassthesamenodetwiceorseveraltimestoreachthedestination).Note:ThedefaultdeviceIPaddressis192.168.0.1.
43DHCP ServerTheDHCPserverassignsIPaddressestothedevicesontheLAN.DHCP ServerEnableordisabletheDHCPserver(Default:Enabled).Lease TimeConguretheamountoftimeeachallocatedIPaddresscanbeusedbyaclient.Start IPTherstIPaddressintherangeofaddressesassignedbytherouter.End IPThelastIPaddressintherangeofaddressesassignedbytherouter.Domain NameThe domain name of the router.
44Conguring Dynamic Host Conguration ProtocolThiswindowallowsyoutoviewandcongureDynamicHostCongurationProtocol(DHCP)addresses.WARNING! Donotmodifythesettingsinthissectionwithoutathoroughunderstandingoftheparameters.ToviewtheDHCPsettings,clickSystem then click DHCP.DHCP Client TableDisplaystheconnectedDHCPclientswhoseIPaddressesareassignedbytheDHCPserveroftherouter.IP AddressDisplaystheIPaddressofthestaticDHCPclientdeviceinthetable.MAC AddressDisplaystheMACaddressofthestaticDHCPclientdeviceinthetable.Expiration TimeThedateandtimewhenthecurrentDHCPaddressis no longer valid.ClickRefreshtoupdatethetable.
45Enable Static DHCP IPTherearereasonswhyyoumaywanttoenableastaticIPaddressonaclientdeviceonyourESRrouter’snetwork.Onoccasion,iftherearepoweroutagesorifyou’vereconguredthesettingsonyourESRrouterandreboot(restart)ittoapplythenewsettings,thepreviousIPaddressthattherouter’sDHCPserverassignedtooneormoredevicesonthenetworkmayhavechanged.Someclientdevicesonyournetworkmayalsohavewebcongurationinterfaces(settopboxes,NetworkAttachedStorage,etc.)thatareaccessiblefromtherouter’sassignedIPaddressfromitsDHCPserver,sotheclientdevicecanbemanaged. Thus if the client device’s IP address changes from timetotime,itmaybedifcultlinkingtoitunlessyounditsnewaddressthroughtheESRrouter’sDHCPClientTable.Ifyouwishtoavoidthis,thentheEnableStaticDHCPIPoptionallowsyousetastatic(essentiallyapermanent)addressforgivenclientdevicesonyournetwork.To do so, select the Enable Static DHCP IP option.IP AddressEntertheIPaddressofthedevicetoaddasastaticDHCPclient.MAC AddressEntertheMACaddressofthedevicetoaddasastaticDHCPclient.ClickAddtoaddthedevicetothestaticDHCPclienttableorReset toreturnthetabletoitspreviousstate.
46Current Static DHCP TableAllowsyoutoviewtheactivestaticDHCPIPaddressesthathavebeenmanuallyassignedtoclientdeviceswiththeircorrespondingMACaddresses.No. (Number)DisplaystheIDofthestaticDHCPclientdeviceinthetable.IP AddressDisplaystheIPaddressofthestaticDHCPclientdeviceinthetable.MAC AddressDisplaystheMACaddressofthestaticDHCPclientdeviceinthetable.SelectClicktoselectstaticDHCPclientdevicestobedeleted.ClickDelete Selectedtoremoveaselectedaddress.ClickDelete All toremovealladdressesfromthetable.ClickReset to return thetabletoitspreviousstate.ClickApply to save the settings or Cancel to discard changes.
47Conguring Event LoggingThe logging service records and displays important system informationandactivityonthenetwork.Theeventsarestoredinamemorybufferwitholderdataoverwrittenbynewerwhenthebufferisfull.ToviewtheLogsettings,clickSystem then click Log.Log Message ListSelect Enable Logging to Syslog Server ClickSave to start logging information to the system.Log Message windowShowsthecurrentsystemoperationsandnetworkactivity.ClickSavetosavethemessagelisttoatextle,Clear to discard messagefromthememorybuffer,orRefresh to clear previous messagesandwritenewmessagestothememorybuffer.ClickApply to save changes.
48Monitoring Bandwidth UsageThistoolallowsyoutoviewreal-timebandwidthusageforWAN(WideAreaNetwork-orInternet),LAN(LocalAreaNetwork)andWLAN(WirelessLocalAreaNetwork)trafc.FortheESR1750,itshowsboththebandwidthtrafcinboththe2.4and5GHzfrequencybands.ToviewtheBandwidthMonitorsettings,clickSystem, then click Monitor.ThescreensdisplaytheactivebandwidthusageforboththeLANandWLANnetworksaswellasthebandwidthbeingusedontheWANconnection.
49Conguring the System LanguageTheESRrouter’sWebCongurationinterfacesupportsmultiplelanguages.ToviewtheLanguagesettings,clickSystem, then click Language.Selectthesystemlanguageyouwishtousefromthedrop-downmenu.
50Conguring IP CamerasThisESRroutersupportsuptofour(4)EnGeniusIPCamerassimultaneously.IfnoIPCameraisdetected,pleasecheckthattheIPCamera’sIPaddressandUPnPclientareconguredcorrectly.ToviewtheIPCamerasettings,clickSystem, then click IP Camera.Beforestartingthisprocedure,youmustconnectyourEnGeniusIPcameratothenetwork.Makesurethecameraispoweredon.ClicktheRefreshbuttontoviewalistingofavailabledevices.Note:The"IPCamera"functionsupportsEnGeniusIPCameraproductsonly.
51Conguring Internet SettingsView Internet StatusTheWANSettings,orInternetStatus,pageshowsasummaryofthe current Internet connection information. This section is alsoshownontheSystemStatuspage.ToviewtheStatussettings,clickInternet, then click Status.WAN SettingsToviewtheWANSettings,clickInternetthenselectStatus.Attain IP ProtocolDisplaytheIPProtocoltypeusedfortheESRSeriesRouter(DynamicIPAddressorStaticIPAddress).IP AddressTherouter’sWANIPaddress.Subnet MaskTherouter’sWANsubnetmask.Default GatewayTheISP’sgatewayIPaddress.MAC AddressTherouter’sWANMACaddress.Therouter’sMACaddressislocatedonthelabelonthebacksideoftherouter.Primary DNSTheprimaryDNSaddressofanISPprovider.Secondary DNSThesecondaryDNSaddressofanISPprovider.
52Conguring Dynamic IPDynamicIPaddressingassignsadifferentIPaddresseachtimeadeviceconnectstoanISP(InternetServiceProvider)andmostcommonlyusedbycableISPs.ToviewtheDynamicIP,clickInternet then select Dynamic IP.Dynamic IPHostnameAssignanamefortheInternetconnectiontype.Thiseldcanbeblank.MTU (Maximum Transmission Unit)AllowsyoutoconguretheMTU.TheMTUspeciesthelargestpacketsizepermittedforaninternettransmission.ThefactorydefaultMTUsizeforDynamicIP(DHCP)is1500.TheMTUsizecanbesetbetween512and1500.Clone MACEntertheMACaddressofyourcomputer’s(ortablet’s)networkembeddedNetworkInterfaceCard(NIC)intheMACaddresseldand click Clone MAC.Note:SomeISPprovidersrequireregisteringtheMACaddressoftheNetworkInterfaceCard(NIC)connecteddirectlytothecableorDSLmodem.CloneMACmaskstherouter'sMACaddresswiththeMACaddressofthecomputer’sNIC.
53DNS ServersTheDNSservertranslatesadomainorwebsitenameintoaURL(UniformResourceLocator),orInternetaddress.Therearetwooptionstochoosefrom:FromISPorUser-Dened.SelectFromISPtoretrievetheDNSaddressvaluefromtheISP;selectUser-DenedtoassignacustomDNSserveraddress.DNS ServerCongurethetypeofDNSserver.(Default=FromISP)First DNS ServerConguretherst,orprimary,DNSserver.Second DNS ServerCongurethesecond,orsecondary,DNSserver.ClickApply to save the settings or Cancel to discard the changes.
54Conguring Static IPSettingastaticIPaddressallowsanadministratortosetaspecicIPaddressfortherouterandguaranteesthatitcannotbeassignedadifferentaddress.ToviewtheStaticIPsettings,clickInternet, then click Static IP.Static IPIP AddressTherouter’sWANIPaddress.Subnet MaskTherouter’sWANsubnetmask.Default GatewayTheWANgatewayaddress.Primary DNSTheprimaryDNSserveraddress.Secondary DNSThesecondaryDNSserveraddress.MTU (Maximum Transmission Unit)TheMTUspeciesthelargestpacketsizepermittedforaninternettransmission.ThefactorydefaultMTUsizeforstaticIPis1500.TheMTUsizecanbesetbetween512and1500.MAC AddressTherouter’sMACaddress.ClickApply to save the settings or Cancel to discard the changes.
55Conguring PPPoEPoint-to-PointProtocoloverEthernet(PPPoE)isusedmainlybyISPsthatprovideDSLmodemstoconnecttotheInternet.ToviewthePPPoEsettings,clickInternet, then click PPPoE.UsernameEntertheusernameassignedbyanISP.PasswordEnterthepasswordassignedbyanISP.Service NameEntertheservicenameofanISP(optional).MTU (Maximum Transmission Unit)Enterthe(MTU).TheMTUspeciesthelargestpacketsizepermittedforaninternettransmission(PPPoEdefault:1492).TheMTUsizecanbesetbetween512and1492.Authentication TypeSelectthetypeofauthenticationprovidedbytheISP:Auto,PAP,orCHAP.Ifunsureofthebestsetting,selectAutoorcheckwithyour Internet Service Provider.TypeConguretheconnectiontypebetweentherouterandtheISP.Selectoneofthefollowing:Keep Connection, Automatic Connection or Manual Connection.Idle TimeoutCongurethemaximumidletime(1to1,000minutes)allowedfor an inactive connection.Clone MACEntertheMACaddressofthedevices’networkinterfacecard(NIC)intheMACaddresseldandclickCloneMAC.Note: SomeISPprovidersrequireregisteringtheMACaddressofthenetworkinterfacecard(NIC)connecteddirectlytothecableorDSLmodem.CloneMACmaskstherouter’sMACaddresswiththeMACaddressofthecomputer’sNIC.ClickApply to save the settings or Cancel to discard thechanges.
56Conguring PPTPPPTP(Point-to-PointTunnellingProtocol)isusedinassociationwithvirtualprivatenetworks(VPNs).TherearetwopartstoaPPTPconnection:theWANinterfacesettingsandthePPTPsettings.ToviewthePPTPsettings,clickInternet, then click PPTP.WAN Interface SettingsDynamic IP AddressWAN Interface TypeSelectDynamicIPAddresstoassignanIPaddressprovidedbyanISP.HostnameEnterahostnameofanISP.(optional).Clone MACEntertheMACaddressofthecomputer’s(ortablet’s)embeddedNetworkInterfaceCard(NIC)intheMACaddresseldandclickClone MAC.Note: SomeISPprovidersrequireregisteringtheMACaddressofthenetworkinterfacecard(NIC)connecteddirectlytothecableorDSLmodem.CloneMACmaskstherouter’sMACaddresswiththeMACaddressofthecomputer’sNIC.
57PPTP SettingsUser NameEntertheusernameassignedbyyourISP.PasswordEnterthepasswordassignedbyyourISP.Service IP AddressEnterthePPTPserverIPaddressprovidedbyyourISP.Connection IDEntertheconnectionIDprovidedbyyourISP(optional).MTU (Maximum Transmission Unit)EnterMTU.TheMTUspeciesthelargestpacketsize(Default:1462)permittedforanInternettransmission.TheMTUsizecanbesetbetween512and1492.TypeConguretheconnectiontypebetweentherouterandtheISP.Selectoneofthefollowing:Keep Connection, Automatic Connection or Manual Connection.Idle TimeoutCongurethemaximumamountoftime,inminutes,allowedforinactiveInternetconnection.TheInternetconnectionwillbedroppedwhenthemaximumidletimeisreached.Validvaluesarebetweenoneandonethousand.ClickApply to save the settings or Cancel to discard the changes.
58Conguring L2TPL2TP(Layer2TunnelingProtocol)isusedinassociationwithVPNs(VirtualPrivateNetworks).TherearetwopartstoaL2TPconnection:1.TheWANinterfacesettings and 2. The L2TP settings.ToviewtheL2TPsettings,clickInternet, then click L2TP.WAN Interface SettingsDynamic IP AddressWAN Interface TypeSelectDynamicIPAddresstoassignanIPaddressprovidedbyanISP.HostnameEnterahostnameofanISP(optional).Clone MACEntertheMACaddressofyourcomputer’sembeddedNetworkInterfaceCard(NIC)intheMACaddresseldandclickClone MAC.Note: SomeISPprovidersrequireregisteringtheMACaddressofthenetworkinterfacecard(NIC)connecteddirectlytothecableorDSLmodem.CloneMACmaskstherouter’sMACaddresswiththeMACaddressofthecomputer’sNIC.
59L2TP SettingsUsernameEntertheusernameassignedbyanISP.PasswordEnterthepasswordassignedbyanISP.Service IP AddressEntertheL2TPserverIPaddressprovidedbyanISP.Connection IDEntertheconnectionIDprovidedbyanISP(optional).MTU (Maximum Transmission Unit)EnterMTU.TheMTUspeciesthelargestpacketsize(Default:1460)permittedforanInternettransmission.TheMTUsizecanbesetbetween512and1492.TypeConguretheconnectiontypebetweentherouterandtheISP.Selectoneofthefollowing:Keep Connection, Automatic Connection or Manual Connection.Idle TimeoutCongurethemaximumamountoftime,inminutes,allowedforinactiveInternetconnection.TheInternetconnectionwillbedroppedwhenthemaximumidletimeisreached.Validvaluesarebetweenoneandonethousand.ClickApply to save the settings or Cancel to discard the changes.
60Conguring DS-LiteDual-StackLite,orDS-Lite,allowsISPstostopIPv4addressesfromreachingacustomer’snetworkdevicesandonlyuseIPv6.ToviewtheDS-Litesettings,clickInternet, then click DS-Lite.DS-Lite CongurationSelectDS-LiteDHCPv6OptionorManualCongurationAFTR IPv6 AddressEnter the AFTR IPv6 connection typeB4 IPv4 AddressEnteranOptionalB4IPv4address.WAN IPv6 AddressEntertheWANIPv6address.IPv6 WAN Default GatewayEntertheIPv6WANdefaultgatewayaddress.ClickApply to save the settings or Cancel to discard the changes.
61Wireless LAN Setup ToviewtheWirelessBasicsettings,clickWireless then select Basic.RadioEnableordisablethewirelessradio.Ifthewirelessradioisdisabled,wirelessaccesspointsarenotavailable.ModeSelectthewirelessoperatingmodefortherouter.Twomodesareavailable:AccessPointorWirelessDistributionSystem(WDS)mode.AP (Access Point)Providesaconnectionaccesspointforwirelessdevices.WDS (Wireless Distribution System)Allowsthewirelessnetworktobeexpandedusingmultipleaccesspointswithoutwiredconnections.ClickApply to save the settings or Cancel to discard changes.
62Access Point ModeTheseinstructionsapplytoboththe2.4GHzand5GHzfrequencybands.TherouterbydefaultisalreadyconguredinAccessPointMode.Foroptimumconnectivitytoanumberofdifferentwirelessclientdevices,it’srecommendedthatyoukeeptherouterinitsdefaultwirelesssettings.Youcanchoosetohavetherouterassociateonlywithcertainiterations(IEEEstandards)andbydoingsothiswilleitherpositivelyornegativelyaffecttherouter’sspeedandthroughput performance. BandSelectawirelessstandardforthenetworkfromthefollowingoptions:• 2.4GHz(IEEE802.11b)• 2.4GHz(IEEE802.11n)• 2.4GHz(IEEE802.11b/g)• 2.4GHz(IEEE802.11g)• 2.4GHz(IEEE802.11b/g/n)• 5GHz(IEEE802.11a)• 5GHz(IEEE802.11n)• 5GHz(IEEE802.11a/n)• 5GHz(IEEE802.11draftac)Enable SSID#Selectthenumberofwirelessgroups,betweenoneandfour,availableonthenetwork.SSID[#]Enterthenameofthewirelessnetwork(s).Auto ChannelEnableordisablehavingtherouterautomaticallyselectachannelforthewirelessnetwork.AutoChannelisenabledbydefault.Selectdisabletomanuallyassignaspecicchannel.(Default=Disable)Check Channel TimeWhenAutoChannelisenabled,selectatimeperiodthatthesystem checks the appropriate channel for the router.ChannelWhenAutoChannelisdisabled,selectachanneltoassigntothewirelessnetwork.Validvaluesarefromonetoeleveninthe US and one to thirteen in the EU.
63Wireless Distribution System ModeConguringtherouter’swirelesssettingsforWDS(WirelessDistributionSystem)mode.ChannelSelectachanneltoassigntothewirelessnetwork.Validvaluesare from one to eleven in the US and one to thirteen in the EU.MAC Address [#]EntertheMACaddress(es)forthewirelessaccesspoint(s)thatarepartoftheWDS.WDS Data RateSelectthedataratefortheWDS.Set SecurityClickSetSecuritytosetuptheWDSsecuritysettingsscreen.
64WDS Security Settings ScreenSelectingthetypeofWDSencryption(Disable,WEPorWPAPre-SharedKey)forthewirelessnetwork.Wired Equivalent Privacy (WEP)Key LengthSelectbetween64-bitand128-encryption.Key FormatSelectthetypeofcharactersusedfortheWEPKey:ASCII(5characters)orHexadecimal(10characters).Default KeySelectthedefaultencryptionkeyforwirelesstransactions.Encryption Key [#]Entertheencryptionkey(s)usedtoencryptthedatapacketsduring data transmission.
65Chapter5 Wireless Encryption
66Wi-Fi Protected Access (WPA) Pre-Shared KeyWPA TypeSelectthetypeofWPA.• WPATemporalKeyIntegrityProtocol(TKIP):Generates a128-bitkeyforeachpacket.• WPA2AdvancedEncryptionStandard(AES): Governmentstandardpacketencryptionwhichis stronger than TKIP.Pre-Shared Key TypeSelectthetypeofpre-sharedkeyasPassphrase(ASCII)orHexadecimal.Pre-Shared KeyEnterthepre-sharedKeyvalue.
67Conguring SecurityEnablingsecurityoptionsonthewirelessnetworktopreventintrusionstosystemsonthewirelessnetwork.ToviewtheSecuritysettings,clickWireless then select Security.SSID SelectionSelectthewirelessnetworkgroupinwhichyouwishtochangeitswirelesssecuritysettings.Broadcast SSIDEnableordisablebroadcastSSID.Choosewhetherornotthewirelessgroupisvisibletoothermembers.Wi-Fi Multimedia (WMM)Enableordisablequalityofserver(QoS)tooptimizethestreamingforbandwidthsensitivedatasuchasHDTVvideostreaming, online gaming, VoIP, videoconferencing, and etc.EncryptionSelect the encryption type for the router.Enable802.1xAuthenticationEnableordisable802.1xauthentication.
68ClickApply to save the settings or Cancel to discard the changes.Wi-Fi Protected Access (WPA) Pre-Shared KeyWPA TypeSelectthetypeofWPAfromthefollowing:• WPA2 Advanced Encryption Standard (AES):RECOMMENDED—GovernmentstandardpacketencryptionwhichisstrongerthanTKIP.• WPA Temporal Key Integrity Protocol(TKIP):Generatesa128-bitkeyforeachpacket.• WPA2 Mixed: MixedmodeallowsclientdevicestorstassociatetotherouterusingWPA2,andiftheyfailtoconnect,thentheyareconnectedviaWPA(TKIP).Encryption TypeEnablingencryptionisstronglyencouragedbecauseunauthorizedpartieswithinrangeofyourrouter’swirelesssignalmayattempttoaccessyourwirelessnetworkandthengainaccesstoprivateinformationondevicesonyournetwork.It’shighlyrecommendedthatyouencryptyourrouterwithWPA2(AES)foroptimalsecurityandthroughputperformance.Alwaysselectastrongpassphrasegreaterthan8characterslongandcomprisedofletters,numbers,andsymbols.Pleasemakenoteofthepassphraseandkeepitinasecurelocationsomewhereinyourhomeincaseyouneedtoretrieveit.Pre-Shared Key TypeSelectthetypeofpre-sharedkeyasPassphrase(ASCII)orHexadecimal.Pre-Shared KeyEnterthePre-sSharedKeyvalue.IMPORTANT! WPA2(AES)offersmuchstrongersecuritythanWEP(WiredEquivalentPrivacy)whichhasbeenandcanbecomprimised.
69WPA RADIUSUsingaRADIUSservertoauthenticatewirelessstationsandprovide a session key to encrypt data during communications.WPA TypeSelect the type of Wireless Protected Access (WPA) from the following:• WPA2 Advanced Encryption Standard (AES):RECOMMENDED—GovernmentstandardpacketencryptionwhichisstrongerthanTKIP.• WPA Temporal Key Integrity Protocol(TKIP):Generatesa128-bitkeyforeachpacket.• WPA2 Mixed: MixedmodeallowsclientdevicestorstassociatetotherouterusingWPA2,andiftheyfailtoconnect,thentheyareconnectedviaWPA(TKIP).RADIUS Server IP AddressEnter the IP address of the server.RADIUS Server PortEntertheportnumberoftheserver.RADIUS Server PasswordEnterthepasswordoftheserver.
70Wired Equivalent Privacy (WEP)Authentication TypeSelectthetypeofauthenticationfromthefollowing:• Open System: WirelessstationscanassociatewiththerouterwithoutWEPencryption• Shared Key: DevicesmustprovidethecorrespondingWEPkey(s)whenconnectingtotherouter• Auto: TherouterautomaticallydetectswhetherOpenSystemorSharedKeyisbeingusedKey LengthSelectbetween64-bitand128-encryption.Key TypeSelectthetypeofcharactersusedfortheWEPKey:ASCII(5characters)orHexadecimal(10characters).Encryption Key [#]Entertheencryptionkey(s)usedtoencryptthedatapacketsduring data transmission.Enable 802.1x AuthenticationEnableordisable802.1xauthentication.
71Conguring FiltersWhenEnableWirelessAccessControlisselected,onlywirelessclientswithMACaddresseslistedinthetableareallowedtoconnecttothewirelessnetwork.ToviewtheFiltersettings,clickWireless then select Filter.Enabling Wireless Access ControlSelect“EnableWirelessAccessControl”DescriptionEnter a description of the device allowedtoconnecttothenetwork.MAC AddressEntertheMACAddressofthewirelessdevice.ClickAdd toappendanewdeviceto the list or Reset to discard changes.WARNING! Incorrectlychangingthesesettingsmaycausethedevicetostopfunctioning.Donotmodifythesettingsinthissectionwithoutathoroughunderstandingoftheparameters.
72MAC Address Filtering TableNo. (Number)Thesequencenumberofthedevice.DescriptionThe description of the device.MAC AddressTheMACaddressofthedevice.SelectIndicatesthedevice(s)thatcanhaveactionsperformedonthem.ClickDelete Selected to remove selected devices from thelist.ClickDelete All to remove all devices from the list.ClickResettodiscardchanges.ClickApply to save the settings or Cancel to discard changes.
73Conguring Wi-Fi Protected SetupWi-FiProtectedSetup(WPS)isanquickandeasywaytoassociateanewwirelessclientdevicetotheencryptedrouterusingaPINortheWPSbuttonsoneachdevice.ToviewtheWPSsettings,clickWireless then select WPS.WPSEnableordisableWPS.WPS Current StatusDisplayswhetherornotthewirelesssecurityiscongured.Self Pin CodeAn8-digitPINwhichisrequiredwhenconguringtherouterforthersttimeinWindows7orVista.SSIDThenameofthewirelessnetwork.Authentication ModeThe current security settings for the correspondingSSID(wirelessnetwork).Passphrase KeyArandomlygeneratedkeycreatedbytherouterduringtheWPSprocess.WPS via Push ButtonClick“Start to Process”toactivateWPS.WPS via PINEnter the PINofawirelessdeviceclick“Start to Process” to activateWPS.
74Conguring Client ListViewthewirelessdevicescurrentlyconnectedtotherouter.ToviewtheClientListsettings,clickWirelessthenselectClientList.InterfaceThetypeofnetworkconnectedtothedevice.MAC AddressTheMACaddressofdeviceconnectedtonetwork.SignalThesignalstrengthofthedeviceconnectedtothenetwork.Idle TimeTheamountoftimetheconnecteddevicehasnotbeenactiveonthenetwork.ClickRefreshtorellthelistwithcurrentlyconnecteddevices.
75Chapter6 Advanced Settings
76Conguring Advanced SettingsAllowsyoutodenetheAdvancedSettingsavailableontherouter.ToviewtheAdvancedsettings,clickWireless then select Advanced.Fragment ThresholdEnterthemaximumsizeofapacketduringdatatransmission.Avaluetoolowcouldleadtolowperformance.RTS ThresholdEntertheRTSthreshold.IfthepacketsizeissmallerthantheRTSthreshold,therouterdoesnotuseRTS/CTStosendthedata packet.Beacon IntervalEnterthebeaconinterval.Thisistheamountoftimethattheroutersetstosynchronizethenetwork.Delivery Trafc Indication Message (DTIM) PeriodEntertheDTIMperiod.TheDTIMisacountdownperiodinformingclientsofthenextpointofbroadcastandmulticastofmessagesoverthenetwork.Validvaluesarebetween1and255.N Data RateSelecttheNdatarate.ThisistherateinwhichtheESRSeriesRouterwilltransmitdatapacketstowirelessNcompatibledevices.WARNING!Incorrectlychangingthesesettingsmaycausethedevicetostopfunctioning.Donotmodifythesettingsinthissectionwithoutathoroughunderstandingoftheparameters.
77Channel BandwidthSelectthechannelbandwidth.ThefactorydefaultisAuto20/40MHz.Thedefaultsettingprovidesthebestperformancebyautoselectingchannelbandwidth.Preamble TypeSelectthepreambletype.LongPreambleprovidesbetterLANcompatibilityandShortPreambleprovidesbetterwirelessperformance.CTS ProtectionSelectthetypeofCTSprotection.UsingCTSProtectioncanlowerthedatacollisionsbetweenWirelessB(802.11b)andWirelessG(802.11g)devicesandlowerdatathroughput.Tx PowerSelectthewirelesssignalstrengthlevel.Validvaluesarebetween25%and100%.ClickApply to save the settings or Cancel to discard changes.
78Setting Up Parental ControlsOffensivewebcontentcanbeblockedwhenaparentspecieskeywords.ParentscanalsolimitInternetaccesswithinaspeciedtimeandday,withaSchedule. A PolicyisaruleprolewhichdescribesthekeywordlterandInternetaccessschedule.Parentscanapply the policy to multiple users or Policy Members.TheParentalControlstoolwillscreenpolicymembersbasedonappliedpolicies.Conguring the Access Control ListToviewtheACLsettings,clickFirewall then select ACL.Viewing the Access Control ListTolearnhowtoviewexistingaccesscontrollist,refertoViewing Parental Policies.Adding a Control PolicyTolearnhowtocreateandaddapolicytotheaccesscontrol list, refer to Adding a Control Policy.ToviewtheWizard settings, click Parental Control then select Wizard.Enable Parental Control (Access Control)ClicktoenableParentalControl.Add PolicyClickthebuttontoaddanewcontrolpolicytothenetwork.Policy TableShowsthecontrolpoliciesavailableonthenetwork.ClickApply to save changes or Cancel to discard them.Note:Bydefault,everyoneisallowedtoviewallthecontentswithoutanylimitationandlter.
79Adding a Control PolicyTherouterprovidesawizardtoguideyouthroughsettingupanewAccessControlPolicy.To start the procedure, click the Add Policybutton.ClickNext to continue the procedure or Cancel to stop theprocedure.Theprocedureconsistsofthefollowingsteps:1.EnterauniquenameforyourpolicyinthePolicyNametexteld.2.ClickPrevtoreturntothepreviousscreen,Nexttocontinuetheprocedure,orCanceltostoptheprocedure.3. Add target devices to the access control policy.
805. Setting up a schedule for the router services.To set up a Service Schedule,followthesesteps: a. Select Allow from the Schedule option. b.Clickthedaysthattheschedulewillbeactive. c.Enterthetimeperiodthattheschedulewillbeactive.6.ClickPrev to return to the previous screen, Next to continue the procedure, Save to save the changes, or Cancel to stop the procedure.To add a device to the Member List, follow these steps: a.ClickMAC or IP from the Filter Type option. b.ClickAddtoshowtheaddclientdialog. c. Enter the name of the device in the Device Nametexteld. d.EntereitheraMACaddressoranIPaddressintheAddress   elddependinguponwhichltertypeyouchose. e.ClicktheAdd Device Button to close the screen and   addthedevicetotheMemberList.4.ClickPrev to return to the previous screen, Next to continue the procedure, Save to save the changes, or Cancel to stop the procedure.
817.SetupakeywordandURLlterlist.Tosetupakeyword/URLlterlist,followthesesteps: a. Select Allow from the Filtering option. b.EnterakeywordorURLintheURL/Keyword text eld. c.ClicktheAddbuttontoaddtheltertothelist. d. Repeat steps a through cforeachlter.8.ClickEnable Application Filtertoltersoftwareapplications.9.ClickPrev to return to the previous screen, Next to continue the procedure, Save to save the changes, or Cancel to stop the procedure.10.Select Enabletosavewebaccessinformationtoalogleor Disable to ignore the information.11.ClickPrev to return to the previous screen, Save to save the changes, or Cancel to stop the procedure.
82Viewing Parental PoliciesAvailableparentalcontrolpoliciesareshowninatableandeachpolicycanbeenabledordisabled,edited,anddeleted.ToviewtheWebsettings,clickParental Control then select Web Monitor.EnableClicktoenableordisablethecontrolpolicy.Policy NameShowsthecontrolpolicyname.Target DeviceShowsthetargetdeviceMACaddressorIPaddress.ScheduleShowsthecontrolpolicyschedule.LoggedShowswhetherthecontrolpolicyisstoringlog information.ModifyEditapolicybyclickingtheEdit Button. DeleteapolicybyclickingtheDelete Button.
83Guest NetworkTheGuestNetworkfunctionenablesyoutoofferInternetconnectivitytovisitorsorguestswhilekeepingothernetworkeddevices(computersandharddrives)andsensitivepersonalorcompanyinformationprivateandsecure.TheGuestNetworkiscontrolledbytheWirelessSSIDfunction.WhentheGuestNetworkfunctionisenabled,theGuestSSIDcanonlygettheinternetconnectionfromWAN,butcannotreachtheclientfromtheLANport.Enabling the Guest NetworkToviewtheSelectionsettings,clickGuest Network then select Selection.Guest NetworkEnableorDisabletheGuestNetworkfunctionClient IsolationGuestclientsareisolatedandcannotcommunicatewitheachother.SSIDChooseaSSIDfortheGuestNetworkused.TheSSIDcanbedenedfromtheWirelesssettingpage.ClickApply to save the settings or Cancel to discard changes.
84Conguring the DHCP Server SettingTheGuestNetworkSSIDshouldbeonadifferentsubnetfromtherouter’sDHCPserver.ToviewtheDHCPServerSettings,clickGuest Network then select DHCP Server Setting.Router IP addressDenetherouterIPaddressfortheGuestnetwork.Default Subnet MaskDenetheSubnetMaskIPaddressfortheGuestnetwork.Start IPTodenetheGuestnetworkDHCPserverstartIP.End IPTodenetheGuestnetworkDHCPserverendIP.ClickApply to save the settings or Cancel to discard changes.
85Viewing the DHCP Client List on the Guest NetworkShowsthelistofguestclientsregisteredonthenetwork.ToviewtheDHCPClientListsettings,clickGuest Network then select DHCP Client List.DHCP Client TableShowstheIPaddress,MACaddress,andexpirationtimeofeachof the registered clients on the list.IP AddressThe IP address of the guest client.MAC AddressTheMACaddressoftheguestclient.Expiration TimeThetimethattheguestclient’sDHCPaddresswillexpireandmustberenewed.ClickRefreshtorefreshtheviewofthelist.
86IPv6Thereareseveralconnectiontypestochoosefrom:AutoDetection,StaticIPv6,Autoconguration(SLAAC/DHCPv6),PPPoE,IPv6inIPv4Tunnel,6to4,andLink-local.Ifyouareunsureofyourconnectionmethod,pleasecontactyourIPv6InternetServiceProvider.Enabling IPv6 SettingsToviewtheBasicsettings,clickIPv6thenselectBasic.BeforeusingorconguringtheIPv6protocol,orIPv6passthrough,onanESRSeriesRouteryoumustenableit.IPv6SelectenabletoconguretheIPv6protocolontherouter.IPv6 PassthroughSelectenabletoallowIPv6passthroughfunctionality.IPv6mustbedisabledtoenablethisfeature.ClickApply to save the settings or Cancel to discard changes.Note:IfyouareusingthePPPoEoption,youwillneedtoensurethatanyPPPoEclientsoftwareonyourcomputershasbeenremovedordisabled.
87Viewing the IPv6 Connection StatusToviewtheStatusinformation,clickIPv6thenselectStatus.IPv6 Connection InformationShowstheIPv6connectiontype,theLANIPv6link-localaddressandtheDHCP-PD.LAN IPv6 Computers ListShowsalistofnetworkcomputersandtheirIPv6connectioninformation.
88Conguring Static IPv6ToviewtheStaticIPv6settings,clickIPv6 then select Static IPv6.Use Link-Local AddressEnableordisableLANlink-localaddress.IPv6 AddressEntertheLAN(local)IPv6addressfortherouter.Subnet Prex LengthEnterthesubnetprexlength.Default GatewayEnterthedefaultgateway.Primary IPv6 DNS AddressEntertheprimaryIPv6DNSaddress.Secondary IPv6 DNS AddressEnterthesecondaryIPv6DNSaddress.LAN IPv6 AddressEntertheLANIPv6address.LAN IPv6 Link-Local AddressEntertheLANIPv6link-localaddress.Enable Automatic IPv6 Address AssignmentEnableordisableautomaticIPv6addressassignment.Autoconguration TypeEntertheautocongurationtype.(Default:SLAAC+RDNSS).Router Advertisement LifetimeEntertheIPv6AddressLifetime(inminutes).ClickApply to save the settings or Cancel to discard changes.
89Setting AutocongurationToviewtheAutoCongurationsettings,clickIPv6 then select Auto Conguration.Obtain A DNS Server Address AutomaticallyEnableordisableobtainingaDNSserverautomatically.Primary IPv6 DNS AddressEntertheprimaryIPv6DNSaddress.Secondary IPv6 DNS AddressEnterthesecondaryIPv6DNSaddress.Enable DHCP-PDEnableordisableDHCP-prexdelegation(PD).LAN IPv6 AddressEntertheLANIPv6address.LAN IPv6 Link-Local AddressEntertheLANIPv6link-localaddress.Enable Automatic IPv6 Address AssignmentEnableordisableautomaticIPv6addressassignment.Autoconguration TypeEntertheautocongurationtype.(Default:SLAAC+RDNSS)Router Advertisement LifetimeEntertheIPv6AddressLifetime(inminutes).ClickApply to save the settings or Cancel to discard changes.
90Conguring PPPoEToviewthePPPoEsettings,clickIPv6 then select PPPoE.Address ModeSelectStaticifyourISPassignedyoutheIPaddress,subnetmask,gateway,andDNSserveraddresses.Inmostcases,selectDynamic.IP AddressEntertheIPaddress(StaticPPPoEonly).User NameEnter your PPPoE user name.PasswordEnteryourPPPoEpassword.Verify PasswordRetypetheyourPPPoEpassword.Service NameEntertheISPServiceName(optional).Reconnect ModeSelecteitherAlways-on,On-Demand,orManual.Maximum Idle TimeEnteramaximumidletimeduringwhichtheInternet connection is maintained during inactivity. Todisablethisfeature,enableAuto-reconnect.MTUMaximumTransmissionUnit-youmayneedtochangetheMTUforoptimalperformancewithyourspecicISP.1492isthedefaultMTU.
91Obtain A DNS Server Address AutomaticallyEnableordisableobtainingaDNSserverautomatically.Primary IPv6 DNS AddressEntertheprimaryIPv6DNSaddress.Secondary IPv6 DNS AddressEnterthesecondaryIPv6DNSaddress.Enable DHCP-PDEnableordisableDHCP-prexdelegation(PD).LAN IPv6 AddressEntertheLANIPv6address.LAN IPv6 Link-Local AddressEntertheLANIPv6link-localaddress.Enable Automatic IPv6 Address AssignmentEnableordisableautomaticIPv6addressassignment.Autoconguration TypeEntertheautocongurationtype.(Default:SLAAC+RDNSS)Router Advertisement LifetimeEntertheIPv6AddressLifetime(inminutes).ClickApply to save the settings or Cancel to discard changes.
92Conguring 6to4Toviewthe6to4settings,clickIPv6 then select 6to4.6to4 AddressEnterthe6to4IPaddress.Primary IPv6 DNS AddressEntertheprimaryIPv6DNSaddress.Secondary IPv6 DNS AddressEnterthesecondaryIPv6DNSaddress.LAN IPv6 AddressEntertheLANIPv6address.LAN IPv6 Link-Local AddressEntertheLANIPv6link-localaddress.Enable Automatic IPv6 Address AssignmentEnableordisableautomaticIPv6addressassignment.Autoconguration TypeEntertheautocongurationtype.(Default:SLAAC+RDNSS)Router Advertisement LifetimeEntertheIPv6AddressLifetime(inminutes).ClickApply to save the settings or Cancel to discard changes.
93Viewing Local ConnectionsToviewtheLinkLocalsettings,clickIPv6 then select Link Local.LAN IPv6 Link-Local AddressEntertheLANIPv6link-localaddress.ClickApply to save the settings or Cancel to discard changes.
94Firewall SetupConguring Basic SettingsToviewtheBasicsettings,clickFirewallthenselectBasic.TheESRSeriesRouterrewallautomaticallydetectsandblocksDenialofService(DoS)attacks.URLblocking,packetlteringandstatefulpacketinspection(SPI)arealsosupported.Thedetailsoftheattackandthetimestamparerecordedinthesecuritylog.FirewallEnableordisabletherewalloftheESRSeriesRouter.ClickApply to save the settings or Cancel to discard changes.Note:ThissectionappliestoClientRoutermode.
95Conguring Advanced SettingsTheroutersupportsVPNpass-throughwhichallowsvirtualprivatenetworking(VPN)packetstopassthroughtherewall.ToviewtheAdvancedsettings,clickFirewallthenselectAdvanced.VPN L2TP Pass-throughClickSelecttoallowanL2TPconnectionmethodoveraVPN.VPN PPTP Pass-throughClickSelecttoallowaPPTPconnectionmethodoveraVPN.VPN IPSec Pass-throughClickSelecttoallowanIPSecconnectionmethodoveraVPN.IPv6 Pass-throughClickSelecttoallowIPv6packetstopassthroughtherewall.PPPoE Pass-throughClickSelecttoallowaPPPoEpacketstopassthroughtherewall.ClickApply to save the settings or Cancel to discard changes.Note: VPNL2TPPass-through,VPNPPTPPass-through,andVPNIPSecPass-throughareenabledbyfactorydefault.
96VPN L2TP Pass-throughClickSelecttoallowanL2TPconnectionmethodoveraVPN.VPN PPTP Pass-throughClickSelecttoallowaPPTPconnectionmethodoveraVPN.VPN IPSec Pass-throughClickSelecttoallowanIPSecconnectionmethodoveraVPN.IPv6 Pass-throughClickSelecttoallowIPv6packetstopassthroughtherewall.PPPoE Pass-throughClickSelecttoallowPPPoEpacketstopassthroughtherewall.ClickApply to save the settings or Cancel to discard changes.Note: VPNL2TPPass-through,VPNPPTPPass-through,andVPNIPSecPass-throughareenabledbyfactorydefault.
97Conguring Demilitarized ZoneConguringadeviceontheLANasaDemilitarizedZone(DMZ)hostallowsunrestrictedtwo-wayInternetaccessforInternetapplications,suchasonlinevideogames,torunfrombehindtheNATrewall.TheDMZfunctionallowstheroutertoredirectallpacketsgoingtotheWANportIPaddresstoaparticularIPaddressontheLAN.ThedifferencebetweenthevirtualserverandtheDMZfunctionisthatavirtualserverredirectsaparticularserviceorInternetapplication,suchasFTP,toaparticularLANclientorserver,whereasaDMZredirectsallpackets,regardlessoftheservice,goingtotheWANIPaddresstoaparticularLANclientorserver.ADMZhostallowsacomputertohaveallitsconnectionsandportscompletelyopenduringdatatransmission.ToviewtheDMZsettings,clickFirewall then select DMZ.Enabling DMZClickEnableDMZtoactivateDMZfunctionality.Local IP AddressEnteranIPaddressofadeviceontheLAN.ClickApply to save the settings or Cancel to discard changes.WARNING!ThePCdenedasaDMZhostisnotprotectedbytherewallandisvulnerabletomaliciousnetworkattacks.DonotstoreormanagesensitiveinformationontheDMZhost.
98Conguring Denial of ServiceToenableblockingofdenialofservice(DoS)attacks,selecttheDoSoptionintheFirewallsection.DoSattackscanoodtheInternetconnectionwiththecontinuoustransmissionofdata.BlockingtheseattacksensuresthattheInternetconnectionisalwaysavailable.ToviewtheDoSsettings,clickFirewall then select DoS.Block DoSEnableordisableblockingDoSattacks.Discard Ping on WANICMP(ping)packagesareblockedwhileBlockDoSisenabled.EnableDiscardPingonWANiftheWANportisrequired.ClickApply to save the settings or Cancel to discard changes.
99Virtual Private Network SetupAVirtualPrivateNetwork(VPN)providesasecureconnectionbetweentworemotelocationsortwousersovertheInternet.Itprovidesauthenticationtosecurelyencryptdatacommunicatedbetweenthetworemoteendpoints.TheShortModelNamesupportsupto5VPNtunnels,makingitidealforsmall-ofce/home-ofceusersoremployeeswhoworkfromhomebutneedtocommunicatesecurelybacktothemainofce.Viewing StatusToviewtheStatussettings,clickVPN then select Status.No. (Number)ThesequencenumberoftheVPNtunnel.NameThenameoftheVPNtunnel.TypeThetypeofVPNtunnel.Gateway/Peer IP AddressTheVPNgatewayorpeerIPaddress.Transmit PacketsThenumberofpacketstransmitted.Received PacketsThenumberofpacketsreceived.UptimeTheamountoftimetheVPNhasbeenactive.SelectIndicatesthedevice(s)thatcanhaveactionsperformedonthem.
100Conguring a VPN Tunnel ProleToviewtheStatussettings,clickVPNthenselectStatus.ManuallycongureaVPNtunnelprole.Creating a Prole• ClickAdd tocreateanewVPNtunnelprole.• ClickEdittoeditthesettingsoftheselectedprole.• ClickDelete Selectedtodeletetheselectedprole.• ClickDelete All todeleteallcurrentproles.
101GeneralFormanuallyconguringaVPNtunnelprole.Name: Enterthenameforthisprole.Connection Type: Clickthedrop-downmenutoselecttheconnectiontype(PPTP,L2TP,IPSec,L2TPoverIPSec).Authentication Type:Clickthedrop-downmenutoselecttheauthentication type.Shared Key:Enterthesharedkeytobeusedforthisprole.Conrm: Enterthesharedkeyasecondtimetoconrmtheshared key.Local ID Type:Clickthedrop-downmenutoselectthetypeofIDusedforthisprole(IPaddress,DomainName,EmailAddress).Local ID: EnterthelocalIDdesignationbasedondenitiontypefromLocalIDType,previouseld.Peer ID type: Clickthedrop-downmenutoselectthetypeofPeerIDforthisprole(IPaddress,DomainName,EmailAddress).Peer ID: EnterthePeerIDdesignationbasedondenitiontypefromPeerIDType,previouseld.Apply: ClickApply to save the changes.Cancel: ClickCancel to delete the changes.
102SA (Security Association)IKE(InternetKeyExchange)isconguredintwonegotiations.Phase1authenticatestheVPNClientstoeachotherbyconrmingthematchingPre-SharedKeywiththetwogateways.IPSecisthePhase2oftheVPNprocess.Manually conguring a VPN tunnel prole.IKE (Phase 1) ProposalExchange:Clickthedrop-downmenutoselectthetypeofexchange(MainMode,AggressiveMode).DH Group:Clickthedrop-downmenutoselecttheDHgroup(group1,group2,group5,group14).Encryption: Clickthedrop-downmenutoselectthetypeofencryption(DES,3DES,AES128,AES192,AES256).Authentication: Clickthedrop-downmenutoselecttheauthenticationprotocol(MD5,SHA1).Life Time: Enter the life time value for Phase 1. The life timevalueshouldbegreaterthanPhase2(IPSec).86400sec.(1day)is a common default and is a normal value for Phase 1.IPSec (Phase 2) ProposalProtocol: Clickthedrop-downmenutoselecttheprotocoltype(ESP,AH)Encryption: Clickthedrop-downmenutoselectthetypeofencryption(DES,3DES,AES128,AES192,AES256).Authentication: Clickthedrop-downmenutoselecttheauthenticationprotocol(MD5,SHA1).Perfect Forward Secrecy (PFS):SelectenabletoenablePFS.AfreshDHkeyisgeneratedduringIKEphaseIIandrenewedforeachkeyexchangetoeliminatedependenciesbetweenthekeys.DH Group: Clickthedrop-downmenutoselecttheDHgroup(group1,group2,group5,group14).Life Time: Enter the life time value for Phase 2. The life timevalueshouldbesmallerthanPhase1(IKE).3600sec.(1hour)is a common value for Phase 2.Apply: ClickApply to save the changes.Cancel:ClickCancel to delete the changes.
103NetworkManually conguring a VPN tunnel prole.Security Gateway Type:Clickthedrop-downmenutoselecttheSecurityGatewayType(IPAddress,DomainName)Security Gateway: EnterthegatewayvalueasdenedinSecurityGatewayType.Local NetworkLocal Address: EntertheIPaddressofthelocalPC.Local Netmask: EnterthenetmaksofthelocalPC.Remote NetworkRemote Address: EntertheIPaddressoftheremotePC.Remote Netmask: EnterthenetmaskoftheremotePC.Apply: ClickApplytosavethechanges.Cancel: ClickCanceltodeletethechanges.
104AdvancedManually conguring a VPN tunnel prole.NAT Traversal: SelectenabletoenabletheNATTraversalfunctioninordertohidetheprivateIPaddressfrompublicview.Note: ServicessuchasVoIPrequiretheuseofaprivateIP address.Dead Peer Detection:Apply: ClickApplytosavethechanges.Cancel: ClickCanceltodeletethechanges.
105Conguring a User SettingTheUserSettingfunctionallowsyoutocreateuserprolesinordertosetuploginaccesstotheVPNservice.NameEnterthenameofthenewuserprole.PasswordEnterthepasswordfortheusername.ConrmEnterthepasswordasecondtimetoconrmthesetting.AddClickAddtoaccepttheproleandaddittotheCurrentVPNUserTable.ResetClickResettoclearthenewsettings.Current VPN User TableDisplaystheUserID,UserNameandSelectionstatus.Delete SelectedClicktodeletetheselecteduserprole.Delete AllClicktodeleteallthecurrentuserproles.ResetClicktocleartheselectionsfromtheCurrentVPNUserTable.ApplyClicktoacceptsavethenewsettings.CancelClicktoclearthenewchanges.
106USB PortTheESR1750routerisequippedwithaUSBportforconnectingaharddrivesomediacontentcanbeaccessedortransferredtootherdevicesinthehomeordevicesawayfromhome.Viewing EnShareTheEnSharefeatureallowsyoutoaccessmediacontentstoredonaUSBharddriveconnectedtotherouter’sUSBportinthehomeandwhenyouareawayfromhomewhenyouhaveaccesstotheInternet.By default the EnShare feature is enabled.To view the EnShare settings or disable EnShare, click USB Port then select EnShare.1. Select DisabletodisabletheEnSharefeature.2.ClickApplytosavethenewsettings.File SharingTheFileSharingfunctionallowsyoutoprovideuserstheabilitytosharelesoverthenetworkthroughtheSambaservice.By default the EnShare feature is enabled.ToviewtheFileSharingsettings,clickUSB Port then select File Sharing.1. Select EnabletoenabletheSambaServicefunction.2.ClickApplytosavethenewsettings,orclickCancel to delete the changes.
107Viewing File ServerTheFileServerfunctionallowsyoutoprovidenetworkusersFTPaccesstosharedUSBstoredles.ToviewtheFileServersettings,clickUSB Port then select File Server.Enable FTP ServiceSelectthistoenabletheFTPservicetosharelesontheUSBdevicePort NumberDenetheportnumber(default:21)toopenfortheFTPservice.Login TimeoutDenetheperiodofinactivity(default:90)beforeauserislogged out.Stay TimeoutDenethelockoutperiod(default:90)beforeauserisallowedto attempt a login.Login UserDenethenumberofconcurrentuserstoaccesstheservice(Max:20users)Share ModeDenethetypeofsharepriviledge:Read/Write,Readonly.Use Anonymous LoginSelectthistoallowanonymoususerlogin.User NameEnter the user name to login to the FTP service.PasswordEnterthepasswordtologintotheFTPservice.
108Viewing DLNATheDLNAMediaServerfunctionallowsyoutotransferphotos,musicandvideobetweennetworkeddevicesthroughtheESRSeriesRouter.ToviewtheDLNAsettings,clickUSB Port then select DLNA.1. Select EnabletoenabletheDLNAMediaServerfunction.2.IntheShareFolderName,enterthenameofthesharedfolder.3.ClickApplytosavethenewsettings,orCancel to clear the changes.
109Advanced Network SettingsNAT SetupNetworkAddressTranslation(NAT)allowsusersontheLANtoaccesstheInternetthroughasinglePublicIPAddressormultiplePublicIPAddresses.NATprovidesrewallprotectionfromhackerattacksandallowsformappingLANIPaddressestoWANIPaddresseswithkeyservicessuchaswebsites,FTP,andvideogameservers.ToviewtheNATsettings,clickAdvanced then select NAT.NATEnableorDisabletheNAT.Network TurbineEnableorDisablethenetworkturbine.Note: Thenetworkturbineisdesignedtoimprovetherouter’sperformance.Thereisabout20~30%improvementwhenthenetworkturbineisenabled.Note: ThenetworkturbinemaycauseproblemswiththeInternetconnection.Disablethenetworkturbinefunctionifyouexperienceconnection issues.ClickApply to save the settings or Cancel to discard changes.
110Port Mapping SetupPortMappingallowsyoutoredirectaparticularrangeofserviceportnumbersfromtheWANtoaparticularLANIPaddress.ToviewthePortMappingsettings,clickAdvanced then select Port Mapping.Enable Port MappingClickEnablePortMappingtoactivateportmapping.DescriptionEnternotesordetailsaboutthemappedportrangeconguration.Local IPEnterthelocalIPaddressoftheserverbehindtheNATrewall.ProtocolSelecttheprotocoltouseformappingfromthefollowing:TCP,UDPorBoth.Port RangeEntertherangeofportstobeforwarded.ClickAddtoappendanewdevicetothelistorReset to discard changes.
111Current Port Mapping TableDisplaysalistofmappedportrangesinuseonthenetwork.No. (Number)Thesequencenumberofthemappedportrange.DescriptionNotesordetailsaboutthemappedportrange.Local IPIP address of the server for the mapped port range.TypeTheprotocolusedtocommunicatewiththeWANportsandLANserver.Port RangeThe range of mapped ports.SelectIndicatesthedevice(s)thatcanhaveactionsperformedonthem.ClickDelete Selected to remove selected devices from the list.ClickDelete All to remove all devices form the list.ClickReset the discard changes.ClickApply to save the settings or Cancel to discard changes.
112Port Forwarding SetupPortforwardingenablesmultipleserverapplicationsonaLANtoserveclientsonaWANoverasingleWANIPaddress.Therouteracceptsincomingclientpackets,ltersthembasedonthedestinationWAN,orpublic,portandprotocolandforwardsthepacketstotheappropriateLAN,orlocal,port.UnliketheDMZfeature,portforwardingprotectsLANdevicesbehindtherewall.ToviewthePortForwardungsettings,clickAdvanced then select Port Forwarding.Enable Port ForwardingClickEnablePortForwardingtoactiveportforwarding.DescriptionEnternotesordetailsabouttheforwardedportconguration.Local IPEnterthelocalIPaddressoftheserverbehindtheNATrewall.ProtocolSelecttheprotocoltouseformappingfromthefollowing:TCP,UDPorBoth.Local PortEntertheLANportnumberthatWANclientpacketswillbeforwardto.Public PortEntertheWANportnumberthatclientswillsendtheirpacketsto.ClickAddtoappendanewcongurationtothetableorResetto discard changes.
113Current Port Forwarding TableThetableofcurrentportforwardingcongurations.ClickDelete Selected to remove selected devices from the list.ClickDelete All to remove all devices form the list.ClickReset the discard changes.ClickApply to save the settings or Cancel to discard changes.
114Port Triggering SetupSomeapplications,suchasonlinegames,videoconferencingandVoIPtelephony,requiremultipleportsforinboundandoutboundtrafc.Ifanapplicationrequiressimultaneoususeofincomingandanoutgoingports,congureporttriggeringtomapalocalportorrangeofportstoaspecicpublicport.Sendingpacketsoutoverthelocalporttriggerstheroutertoopenanincominglocalportthatismappedtothesamepublicportandapplicationastheoutgoinglocalport(s).Thelocalapplicationcancommunicateovertheincomingandoutgoingportswithouttheneedforcreatingaxedaddress.ToviewthePortTriggeringsettings,clickAdvanced then select Port Triggering.Enable Port TriggeringClickEnableTriggerPorttoactivateporttriggering.DescriptionEnternotesordetailsabouttheporttriggeredconguration.Popular ApplicationsSelectadefaultapplicationoraddanewone.Trigger PortEntertheapplication’soutboundportnumber(s).Trigger TypeSelecttheprotocoltouseforporttriggeringfromthefollowing:TCP,UDPorBoth.Public PortEntertheinboundport(s)fortheapplicationinthefollowingformat:2300-2400or47624.
115Public TypeSelecttheprotocoltousefortheinboundportfromthefollowing:TCP,UDPorBoth.ClickAdd toappendanewcongurationtothetableorReset to discard changes.Current Port Triggering TableThelistofcurrentporttriggeringcongurations.ClickDeleteSelectedtoremoveselecteddevicesfrom the list.ClickDelete All to remove all devices form the list.ClickReset the discard changes.ClickApplytosavethesettingsorCanceltodiscardchanges.
116Application Layer Gateway SetupTheALG(ApplicationLayerGateway)servesasawindowbetweencorrespondentapplicationprocessessothattheymayexchangeinformation on an open environment.ToviewtheALGsettings,clickAdvanced then select ALG.SelectthelistedapplicationsthatneedALGsupportandthentherouterwillauthorizethemtopassthroughtheNATgateway.ClickApply to save the settings or Cancel to discard changes.
117Universal Plug and Play SetupUPnPhelpsinternetdevices,suchasgamingandvideoconferencing,toaccessthenetworkandconnecttootherregisteredUPnPdevices.ToviewtheUPnPsettings,clickAdvanced then select UPnP.ClickEnable or Disable to activate or deactivate UPnP.ClickApply to save the settings or Cancel to discard changes.
118Internet Group Multicast Protocol SetupInternetGroupMulticastProtocol(IGMP)isanetwork-layerprotocolusedtoestablishmembershipinamulticastgroup.ToviewtheIGMPsettings,clickAdvanced then select IGMP.ClickEnable or Disable toactivateordeactivateIGMP.ClickApply to save the settings or Cancel to discard changes.Note: DisablingtheMulticastfunctionmaycauseIPbasedmultimediadevices,suchasanIP-STBorOTTbox,mayloseconnectivitywiththemediastreamingserver.
119Quality of Service SetupQoScanprioritizebandwidthusesuchasvideostreaming,onlinegaming,VoIPtelephonyandvideoconferencingtoensurestableandefcientnetworkperformance.ToviewtheQoSsettings,clickAdvanced then select QoS.Total Bandwidth SettingsUplinkSelectthemaximumbandwidthspeedforoutboundtrafc.DownlinkSelectthemaximumbandwidthspeedforinboundtrafc.Note:ClickDisabled ifyoudonotwanttoprioritizeanydataorprotocol.
120Priority QueueSetnetworkresourceusagebasedonspecicprotocolsorportranges.Incomingpacketsareprocessedbasedontheprotocols’positionwithinthequeue.Unlimited Priority QueueLocal IP AddressEnterthelocalIPaddressofadeviceonthenetwork.Thisdevice’sactivityisnotrestrictedbytheQoSfeature.High/Low Priority QueueSpecify the priority for different protocols. Additional protocolsandportrangescanbeadded.ClickApply to save the settings or Cancel to discard changes.
121Bandwidth AllocationSetnetworkresourceusage,forinboundandoutboundtrafc,basedonlocalIPandportranges.TypeSelectDownloadorUploadtospecicthedirectionofpackettrafc.Local IP RangeEnterthelocalIPrangeofthecurrentconguration.ProtocolSelecttheprotocoltomanageforthecurrentconguration.Port RangeEnterthelocalportrangeofthecurrentconguration.PolicySelectMinorMaxtospecifythetypeofcongurationpolicy.Rate (bps)Selectthebandwidthrate,inbitspersecond(bps),ofthecurrentconguration.ClickAdd tosavethesettingsandlistthecongurationintheCurrentQoStableorReset the discard changes.ClickApply to save the settings or Cancel to discard changes.
122Routing SetupTypicallystaticroutingdoesnotneedtobesetupbecausetherouterhasadequateroutinginformationafterithasbeenconguredforInternetaccess.Staticroutingisonlynecessaryiftherouterisconnectedtonetworkunderadifferentsubnets.ToviewtheRoutingsettings,clickAdvanced then select Routing.Note: Toenableastaticrouting,NATmustbedisabled.Iftherouterisconnectedwithanetworkunderthedifferentsubnet,theroutingsetupallowsthenetworkconnectionwithintwodifferentsubnets.Enable Static RoutingClickEnableStaticRoutingtoactivatethefeature.Destination LAN IPEntertheLANIPaddressofthedestinationdevice.Subnet MaskEntertheSubnetMaskofthedestinationdevice.Default GatewayEnterthedefaultgatewayIPaddressforthedestinationdevice.HopsEnterthemaximumnumberofhopswithinthestaticroutingthatapacketisallowedtotravel.InterfaceSelectLANorWANastheinterface.ClickAddtosavethesettingsandlistthecongurationintheCurrentStaticRoutingtableorReset the discard changes.View and select devices in the Current Static Routing Table.ClickDelete Selected or Delete All to remove devicesfromthetable.ClickReset to stop.ClickApply to save the settings or Cancel to discard changes.
123Wake on LAN SetupWakeonLANsetup(WOL)allowstheadministratortoactivateacomputeroverthenetwork.ToviewtheWOLsettings,clickAdvanced then select WOL.Enabling WOL over WAN ClickEnable WOL over WAN to activate the feature.Server Port Enter the server port of the device to activate.Wake MAC Address EntertheMACaddressofthedevicetoactivate.ClickStart to activate the device.ClickApply to save the settings or Cancel to discard changes.
124Tools SetupConguring the Administrator AccountChangetherouter’ssystempasswordaswellassetupadevicetoremotelycongurethesettings.ToviewtheAdminsettings,clickTools then select Admin.• Login Name:Keeporchangeexistingloginname• Old Password:Entertheexistingadministratorpassword• New Password:Enterthenewadministratorpassword• Repeat New Password: Re-typethenewadministratorpassword• Graphical Authentication: ToenableordisableCAPTCHARemote Management• Host Address: Enter the designated host IP Address.• Port: Entertheportnumber(Default:8080)forremoteaccessingmanagementwebinterface.• Enable:Selecttoenableremotemanagement.ClickApply to save the settings or Cancel to discard changes.Note: To access the settings of the ESR Series Router remotely, entertherouter’sWANIPaddressandportnumber.
125System Time SettingChangethesystemtimeoftheESRSeriesRouterandsetupautomaticupdatesthroughanetworktime(NTP)protocolserverorthrough a computer.ToviewtheTimesettings,clickTools then select Time.Synchronizing with an NTP ServerTime SetupSelecthowtheESRSeriesRouterobtainsthe current time.Time ZoneSelectthetimezonefortheESRSeriesRouter.NTP Time ServerEnterthedomainnameorIPaddressofanNTPserver.Enabling Daylight SavingsClicktoenableordisabledaylightsavingstime.Start TimeSelectthedateandtimewhendaylightsavingstimestarts.End TimeSelectthedateandtimewhendaylightsavingstimeends.ClickApply to save the settings or Cancel to discard changes.
126Synchronizing Time with a ComputerTime SetupSelecthowtheESRSeriesRouterobtainsthecurrenttime.Computer Date and TimeDisplayssystemdateandtimefromacomputer.Enable Daylight SavingClicktoenableordisabledaylightsavingstime.Start TimeSelectthedateandtimewhendaylightssavings time starts.End TimeSelectthedateandtimewhendaylightssavingstimeends.ClickApply to save the settings or Cancel to discard changes.
127Dynamic Domain Name Service (DDNS) SetupThemostcommonuseforDDNSisinallowinganInternetdomainnametobeassignedtoacomputerwithavarying(dynamic)IPaddress.ThismakesitpossibleforothersitesontheInternettoestablishconnectionstothemachinewithoutneedingtotracktheIPaddress themselves.ToviewtheDDNSsettings,clickTools then select DDNS.Dynamic DNSClicktoenableordisableDDNS.Server AddressSelect the server address.Host NameEnter the host name.UsernameEnter a username for the host service.PasswordEnterapasswordforthehostservice.ClickApply to save the settings or Cancel to discard changes.
128Diagnosis that Client Devices Are Connected to the RouterThediagnosisfeatureallowstheadministratortoverifythataclientdeviceisavailableonthenetworkandisacceptingrequestpackets.Ifthepingresultreturnsalive,itmeansadeviceisconnected.Thisfeaturedoesnotworkifthetargetdeviceisbehindarewallorhassecuritysoftwareinstalled.ToviewtheDiagnosissettings,clickTools then select Diagnosis.Diagnosing a Network Connection ProblemAddress to PingEnter IP address of the device to ping.Ping FrequencySelect the interval, in seconds, that the ping message is sent out.ClickStarttobeginthediagnosis.
129Upgrading The Router’s FirmwareFirmwareistherouter’ssystemsoftwarethatoperatesandallowstheadministratortointeractwithit.ToviewtheFirmwaresettings,clickTools then select Firmware.WARNING! Upgradingrmwarethroughawirelessconnectionisnotrecommended.FirmwareupgradingmustbeperformedwhileconnectedtoanEthernet(LANport)withallotherclientsdisconnected.Toupdatethermwareversion,followthesesteps:1.DownloadtheappropriatermwareapprovedbyEnGeniusfromanEnGeniuswebsite.SeetheDownloads tab on the product page for this product.Fornewproducts,newrmwaremaynotbereadilyavailable.2.ClickChoose File.3.Browsethelesystemandselectthermwarele.4.ClickApply.
130Backing Up The Router’s SettingsSavethemasacongurationleonyourcomputer.ToviewtheBack-upsettings,clickTools then select Back-up.Restoring to the router’s Factory Default settingsClickResettorestoretheESRSeriesRoutertofactorydefaults.Backup SettingsClickSave tosavethecurrentcongurationontheroutertoa*.dlfle.Restore SettingsTorestoresavedsettings,dothefollowing:a.ClickChoose File.b.Browsethelesystemforlocationofthesettingsle(*.dlf).c.ClickUpload.
131Rebooting the RouterThisfeatureallowsyoutoreboottherouterintheeventofasystemhanguporotherdisruptiontothenetwork.ToviewtheResetsettings,clickTools then select Reset.ClickApply to reset the device.
132Appendix
133Wall Mounting The RouterThefollowingareinstructionsifyouchoosetomounttherouteronawall.Note: ChoosealocationthatiswithinreachofanelectricaloutletfortheACadapterandtheDSLorCablemodem.Tomountthedeviceonthewalldothefollowing:1.Measurethedistancefromthemiddleofeachmountingscrewhole.2.Markthelocationsofthescrewholesonthewall.3.Drillaholeforeachmarkedlocationandinsertascrewineach.Note: Makesuretoleaveenoughofthescrewheadabovethewallsurfacetosecuretherouter.4.Installandsecurethemountsontotherouter.5.Installtherouteronthewall.
134Federal Communication Commission Interference Statement ThisequipmenthasbeentestedandfoundtocomplywiththelimitsforaClassBdigitaldevice,pursuanttoPart15oftheFCCRules.Theselimitsaredesignedtoprovidereasonableprotectionagainstharmfulinterferenceinaresidentialinstallation.Thisequipmentgenerates,uses andcan radiateradio frequencyenergy and,if notinstalled andused inaccordance withthe instructions,maycauseharmfulinterferencetoradiocommunications.However,thereisnoguaranteethatinterferencewillnotoccurinaparticularinstallation.Ifthisequipmentdoescauseharmfulinterferencetoradioortelevisionreception,whichcanbedeterminedbyturningtheequipmentoffandon,theuserisencouragedtotrytocorrecttheinterferencebyoneofthefollowingmeasures:• Reorient or relocate the receiving antenna.• Increasetheseparationbetweentheequipmentandreceiver.• Connecttheequipmentintoanoutletonacircuitdifferentfromthattowhichthereceiverisconnected.• Consultthedealeroranexperiencedradio/TVtechnicianforhelp.FCC Caution: Anychangesormodicationsnotexpresslyapprovedbythepartyresponsibleforcompliancecouldvoidtheuser’sauthoritytooperatethisequipment.ThisdevicecomplieswithPart15oftheFCCRules.Operationissubjecttothefollowingtwoconditions:(1)Thisdevicemaynotcauseharmfulinterference,and(2)thisdevicemustacceptanyinterferencereceived,includinginterferencethatmaycauseundesired operation.Thistransmittermustnotbeco-locatedoroperatinginconjunctionwithanyotherantennaortransmitter.Operationsinthe5.15-5.25GHzbandarerestrictedtoindoorusageonly.IMPORTANT NOTE:FCC Radiation Exposure Statement: ThisequipmentcomplieswithFCCradiationexposurelimitssetforthforanuncontrolledenvironment.Thisequipmentshouldbeinstalledandoperatedwithminimumdistance20cmbetweentheradiator&yourbody.
135Industry Canada Statement ThisdevicecomplieswithRSS-210oftheIndustryCanadaRules.Operationissubjecttothefollowingtwoconditions:(1)Thisdevicemaynotcauseharmfulinterference,and(2)thisdevice mustacceptanyinterferencereceived,includinginterferencethatmaycause undesired operation.CedispositifestconformeàlanormeCNR-210d’IndustrieCanadaapplicableauxappareilsradioexemptsdelicence.Sonfonctionnementestsujetauxdeuxconditionssuivantes:(1)ledispositifnedoitpasproduiredebrouillagepréjudiciable,et(2)cedispositifdoitacceptertoutbrouillagereçu,ycomprisunbrouillagesusceptibledeprovoquerunfonctionnementindésirable.Caution :(i) thedeviceforoperationintheband5150-5250MHzisonlyforindoorusetoreducethepotentialforharmfulinterferencetoco-  channelmobilesatellitesystems;(ii)high-powerradarsareallocatedasprimaryusers(i.e.priorityusers)ofthebands5250-5350MHzand5650-5850MHzandthatthese  radarscouldcauseinterferenceand/ordamagetoLE-LANdevices.Avertissement:(i) lesdispositifsfonctionnantdanslabande5150-5250MHzsontréservésuniquementpouruneutilisationàl’intérieuranderéduire  lesrisquesdebrouillagepréjudiciableauxsystèmesdesatellitesmobilesutilisantlesmêmescanaux;(ii)Deplus,lesutilisateursdevraientaussiêtreavisésquelesutilisateursderadarsdehautepuissancesontdésignésutilisateursprincipaux  (c.-à-d.,qu’ilsontlapriorité)pourlesbandes5250-5350MHzet5650-5850MHzetquecesradarspourraientcauserdubrouillageet/  oudesdommagesauxdispositifsLAN-EL.FOR MOBILE DEVICE USAGERadiation Exposure Statement: ThisequipmentcomplieswithICradiationexposurelimitssetforthforanuncontrolledenvironment.Thisequipmentshouldbeinstalledandoperatedwithminimumdistance20cmbetweentheradiator&yourbody.Déclaration d’exposition aux radiations: Cetéquipementestconformeauxlimitesd’expositionauxrayonnementsICétabliespourunenvironnementnoncontrôlé.Cetéquipementdoitêtreinstalléetutiliséavecunminimumde20cmdedistanceentrelasourcede rayonnement et votre corps.
136ThisdevicecomplieswiththeessentialrequirementsoftheR&TTEDirective1999/5/EC.ThefollowingtestmethodshavebeenappliedinordertoprovepresumptionofconformitywiththeessentialrequirementsoftheR&TTEDirective1999/5/EC:• EN60950-1 SafetyofInformationTechnologyEquipment• EN50385 Generic standard to demonstrate the compliance of electronic and electrical apparatus with the basic restrictions related to human  exposuretoelectromagneticelds(0Hz-300GHz)• EN 300 328 ElectromagneticcompatibilityandRadiospectrumMatters(ERM);WidebandTransmissionsystems;Datatransmissionequipmentoperating  inthe2,4GHzISMbandandusingspreadspectrummodulationtechniques;HarmonizedENcoveringessentialrequirementsunderarticle  3.2oftheR&TTEDirective• EN 301 893  BroadbandRadioAccessNetworks(BRAN);5GHzhighperformanceRLAN;HarmonizedENcoveringessentialrequirementsofarticle3.2  oftheR&TTEDirective• EN 301 489-1  ElectromagneticcompatibilityandRadioSpectrumMatters(ERM);ElectroMagneticCompatibility(EMC)standardforradioequipmentand  services;Part1:Commontechnicalrequirements• EN 301 489-17 ElectromagneticcompatibilityandRadiospectrumMatters(ERM);ElectroMagneticCompatibility(EMC)standardforradioequipmentand  services;Part17:Specicconditionsfor2,4GHzwidebandtransmissionsystemsand5GHzhighperformanceRLANequipmentEurope – EU Declaration of Conformity
137Thisdeviceisa5GHzwidebandtransmissionsystem(transceiver),intendedforuseinallEUmemberstatesandEFTAcountries,exceptinFranceandItalywhererestrictiveuseapplies.InItalytheend-usershouldapplyforalicenseatthenationalspectrumauthoritiesinordertoobtainauthorizationtousethedeviceforsettingupoutdoorradiolinksand/orforsupplyingpublicaccesstotelecommunicationsand/ornetworkservices.ThisdevicemaynotbeusedforsettingupoutdoorradiolinksinFranceandinsomeareastheRFoutputpowermaybelimitedto10mWEIRPinthefrequencyrangeof2454–2483.5MHz.Fordetailedinformationtheend-usershouldcontactthenationalspectrumauthority in France.Česky [Czech] [Jméno výrobce] tímto prohlašuje, že tento [typ zařízení] je ve shodě se základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES.Dansk [Danish] Undertegnede [fabrikantens navn] erklærer herved, at følgende udstyr [udstyrets typebetegnelse] overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF.Deutsch [German] Hiermit erklärt [Name des Herstellers], dass sich das Gerät [Gerätetyp] in Übereinstimmung mit den grundlegenden Anforderungen und den übrigen einschlägigen Bestimmungen der Richtlinie 1999/5/EG bendet.Eesti [Estonian] Käesolevaga kinnitab [tootja nimi = name of manufacturer] seadme [seadme tüüp = type of equipment] vastavust direktiivi 1999/5/EÜ põhinõuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele sätetele.English Hereby, [name of manufacturer], declares that this [type of equipment] is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.Español [Spanish] Por medio de la presente [nombre del fabricante] declara que el [clase de equipo] cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE.Ελληνική [Greek] ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ [name of manufacturer] ΔΗΛΩΝΕΙ ΟΤΙ [type of equipment] ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 1999/5/ΕΚ.
138Français [French] Par la présente [nom du fabricant] déclare que l’appareil [type d’appareil] est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE.Italiano [Italian] Con la presente [nome del costruttore] dichiara che questo [tipo di apparecchio] è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE.Latviski [Latvian] Ar šo [name of manufacturer / izgatavotāja nosaukums] deklarē, ka [type of equipment / iekārtas tips] atbilst Direktīvas 1999/ 5/EK būtiskajām prasībām un citiem ar to saistītajiem noteikumiem.Lietuvių [Lithuanian] Šiuo [manufacturer name] deklaruoja, kad šis [equipment type] atitinka esminius reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas.Nederlands [Dutch] Hierbij verklaart [naam van de fabrikant] dat het toestel [type van toestel] in overeenstemming is met de essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/EG.Malti [Maltese] Hawnhekk, [isem tal-manifattur], jiddikjara li dan [il-mudel tal-prodott] jikkonforma mal-ħtiġijiet essenzjali u ma provvedimenti oħrajn relevanti li hemm d-Dirrettiva 1999/5/EC.Magyar [Hungarian] Alulírott, [gyártó neve] nyilatkozom, hogy a [... típus] megfelel a vonatkozó alapvetõ követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak.Polski [Polish] Niniejszym [nazwa producenta] oświadcza, że [nazwa wyrobu] jest zgodny z zasadniczymi wymogami oraz pozostałymi stosownymi postanowieniami Dyrektywy 1999/5/EC.Português [Portuguese] [Nome do fabricante] declara que este [tipo de equipamento] está conforme com os requisitos essenciais e outras disposições da Directiva 1999/5/CE.Slovensko [Slovenian] [Ime proizvajalca] izjavlja, da je ta [tip opreme] v skladu z bistvenimi zahtevami in ostalimi relevantnimi določili direktive 1999/5/ES.Slovensky [Slovak] [Meno výrobcu] týmto vyhlasuje, že [typ zariadenia] spĺňa základné požiadavky a všetky príslušné ustanovenia Smernice 1999/5/ES.Suomi [Finnish] [Valmistaja = manufacturer] vakuuttaa täten että [type of equipment = laitteen tyyppimerkintä] tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen.Svenska [Swedish] Härmed intygar [företag] att denna [utrustningstyp] står I överensstämmelse med de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv 1999/5/EG.

Navigation menu