Elpas Solutions B05 User Manual New

Elpas Solutions Ltd. New

Contents

New User Manual

Alert Tag Instruction Manual and Spec-SheetFCC ComplianceThe FCC Wants You to KnowThis equipment has been tested and found to comply with the limitsfor a Class B digital device, pursuant to Part 15 of the FCC rules.These limits are designed to provide reasonable protection againstharmful interference in a residential installation. This equipmentgenerates, uses and can radiate radio frequency energy and, if notinstalled and used in accordance with the instructions, may causeharmful interference to radio communications. However, there is noguarantee that interference will not occur in a particular installation.If this equipment does cause harmful interference to radio ortelevision reception, which can be determined by tuning theequipment off and on, the user is encouraged to try to correct theinterference by one or more of the following measures:a) Reorient or relocate the receiving antenna.b) Increase the separation between the equipmentand receiver.c) Connect the equipment to an outlet on a circuitdifferent from that to which the receiver isconnected.d) Consult the dealer or an experienced radio/TVtechnician.FCC WarningModifications not expressly approved by manufacturer could voidthe user authority to operate the equipment under FCC rules.15.9 (a) Labeling RequirementsThis device complies with Part 15 of the FCC Rules. Operation is subject to thefollowing two conditions. (1) This device may not cause harmful interference, and (2)this device must accept any interference received, including interference that maycause undesired operation.
IR and RF Alert TagP/N: ALB00001 (433.92 MHz)IR/RF Alert TagDescriptionA small light-weight, oval badge. The tag sends Infra Red signals, and in additionsends RF signals in the frequency of 433.92 MHz. Designed especially for theconvenience of the elderly or persons in stressful situations (alert, panic, etc.).GeneralElectrical powersource One 3-Volt lithium batteryData rate 19,200 bits per secondModulation ASK (Amplitude Shift Keying of IR or RF carrier)Messageprotocol 4 bytes proprietary formatMessageduration 2.08 msButton on badge Location dependent function. Twelve identical buttonmessages are transmitted 0.4 sec apart on every buttonpress. Button press transmitted with IR and RF message.Button press decoded by IR and RF Readers or CentralPC.Battery type CR 2032 RenataBattery life One year, assuming movement 12 hr / dayBattery statusindication Battery status transmitted with every RF and IR messageBadge ID Unique factory programmed (ID code, transmit rate,motion sensor activation and deactivation, etc.)Dimensions Pendant shape 55 x 35 x 18 mmWeight(includingbattery)25 gramTemperature:Operating -10 to 70°C
Temperature:Storage -20 to 60°CHumidity:Operating Operating – 5 to 95% RH @ 70°CHumidity :Storage Non Operating (12 Hours) – 5 to 95% RH @ 85°CAccessories Neck strap (included)IR TransmissionPeak opticaltransmittedpower500mWPeaktransmissionwavelength880nmPeak radiantintensity 120 mW/SrFrequency oftransmission Carrier at 455 KHzTransmissionrate During human movement – every 3 to 5 sec message.During rest (no movement) – every 60 secTransmissionangle 360° badge plane. ±60° to badge perpendicular axisEMCcompliance Refer to Appendix A and BRF Transmission433.92 MHz RFModulation ASK (Amplitude Shift Keying of 433.92 MHz carrier)Averageeffectiveradiated powerIn motion: less than –35 dbm. Motionless: less than –45dbmStability +/- 20ppmPeak ERP -15 dbm (max)Transmissionpattern Omnidirectional
Using the Alert TagThe following is a set of procedures to ensure proper use of the Alert Tag.To use the Alert Tag:1. For general use, place the strap of the Alert Tag around the person’s neck.2. In case of emergency press the large press button.Battery ReplacementThe battery is located inside the Alert Tag. In order to replace the battery, you needto open the back side of the Alert Tag with a Phillips screwdriver (preferably anelectric one) with point size "0". For example, the APEX #4910. A new battery canthen be inserted, after which the screw must be replaced.

Navigation menu