Elo Touch Solutions PAYPOINT POS User Manual

Elo Touch Solutions, Inc. POS

User manual

USER MANUAL Elo Touch Solutions PayPoint Android Rev. B
User Manual – PayPoint Android Rev B UM600xxx Rev A, page 2 of 26 Copyright © 2016 Elo Touch Solutions, Inc. All Rights Reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, including, but not limited to, electronic, magnetic, optical, chemical, manual, or otherwise without prior written permission of Elo Touch Solutions, Inc. Disclaimer The information in this document is subject to change without notice. Elo Touch Solutions, Inc. and its Affiliates (collectively “Elo”) makes no representations or warranties with respect to the contents herein, and specifically disclaims any implied warranties of merchantability or fitness for a particular purpose. Elo reserves the right to Revise this publication and to make changes from time to time in the content hereof without obligation of Elo to notify any person of such revisions or changes. Trademark Acknowledgments AccuTouch, CarrollTouch, Elo, Elo (logo), Elo Touch, Elo Touch Solutions, Elo TouchSystems, IntelliTouch, iTouch, SecureTouch, TouchTools and VuPoint are trademarks of Elo and its Affiliates. Windows is a trademark of Microsoft Corporation.
User Manual – PayPoint Android Rev B UM600xxx Rev A, page 3 of 26 Table of Contents Section 1: Introduction ............................................................................................................................................................................................................................... 4 Section 2: PayPoint Unpacking and Operation .......................................................................................................................................................................................... 5 Section 3: Technical Support and Maintenance ...................................................................................................................................................................................... 11 Section 4: Safety ...................................................................................................................................................................................................................................... 18 Section 7: Regulatory Information ............................................................................................................................................................................................................ 19 Section 5: Warranty Information............................................................................................................................................................................................................... 21
User Manual – PayPoint Android Rev B UM600xxx Rev A, page 4 of 26 Section 1: Introduction Product Description The Elo PayPoint register is an all-in-one Android based cash register that comes equipped with built-in receipt printer, magnetic stripe reader, barcode reader, cash drawer, and customer facing display. In addition to its built-in peripherals, the system has a USB port that allows for connectivity of external USB devices. Precautions Follow all warnings, precautions and maintenance as recommended in this user manual to maximize the life of your unit and prevent risks to user safety. See Section 6 for more information on safety. This manual contains information that is important for the proper setup of the scanner. Before setting up and powering on your new scanner, read through this manual, especially the Installation, configuration, and Operation chapters.
User Manual – PayPoint Android Rev B UM600xxx Rev A, page 5 of 26 Section 2: PayPoint Unpacking and Operation Box Contents Verify that the box contains: • PayPoint Android Unit • Quick Install Guide • PayPoint Power Cable (color should match PayPoint unit) • 2 receipt paper rolls • 2 cash drawer keys
User Manual – PayPoint Android Rev B UM600xxx Rev A, page 6 of 26 Elo PayPoint Register Layout A. Register Display Head 1 MSR 2 Main Display 3 Barcode Scanner B. Register Base 4 Customer Facing Display 5 USB 2.0 Port 6 Receipt Printer 7 Cash Drawer 8 Cash Drawer Lock 9 Printer door release button 10 Check/Media Slot 11 Receipt Printer 12 Speaker 13 Cash Drawer Release 14 Ethernet Port 15 Mini USB 2.0 Port 16 Power Port - -
User Manual – PayPoint Android Rev B UM600xxx Rev A, page 7 of 26 Register Display Head The Elo PayPoint Register display head can be flipped to allow customers to complete purchase transactions by self-swiping payment cards, and to authorize transactions by signing directly onto the touchscreen. Figure 3. Elo PayPoint display head can be flipped and supports two configurations: Elo PayPoint Register cashier-facing view (top) and customer-facing view (bottom) 1. Magnetic Stripe Reader (MSR) The register has a built in encryptable magnetic stripe reader. Application provider is responsible for correctly encrypting the reader. When the register is in clerk view, the MSR will be on the left of the register display head. When register is in customer view, the MSR will be on the right of the register display head. 2. Touchscreen The Elo PayPoint Register is equipped with a multi-touch touchscreen.
User Manual – PayPoint Android Rev B UM600xxx Rev A, page 8 of 26 4. Barcode scanner The register has a built in barcode scanner that scans 1-D barcodes. When the register is in cashier view, the barcode scanner will be on the right of the register display head. 5. Customer-facing display The register base is equipped with a customer-facing display. As a cashier rings up customer orders, the customer facing display will display each order. 6. USB port (USB 2.0) This USB port can be used to charge your mobile device. Note: In order to comply with PCI compliance and to prevent security breaches, this USB port will not be accessible for connecting the register with other USB devices (e.g. mouse, keyboard, storage device) 7. Receipt printer (built-in) The register is equipped with a built-in receipt printer that is located on the register base. 8. Cash drawer The register is equipped with a cash drawer for storing cash, coins, and checks. 9. Cash drawer lock Use the key that comes with the Elo PayPoint Register to lock / unlock the cash register. When cash drawer is locked, cash drawer will not open even when it is commanded to. 10. Printer head release button Press this release button to release the printer head cover. For more information on how to change printer paper on the register, refer to the “Printer Maintenance” section of Chapter 8. 11. Check compartment slot The cash drawer is designed with a slot for slipping checks into the cash drawer.
User Manual – PayPoint Android Rev B UM600xxx Rev A, page 9 of 26 12. Printer Feed Button Press the printer feed button to feed paper through the PayPoint Printer 13. Speaker (built-in) The register is equipped with a built-in speaker. 14. Cash drawer manual release latch A latch located on the bottom of the register base can be used to manually open the cash drawer. 15. USB port This USB port can be used to charge your mobile device. Note: In order to comply with PCI compliance and to prevent security breaches, this USB port will not be accessible for connecting the register with other USB devices. 16. Ethernet (LAN) port Use this port to connect the register to a network via an Ethernet RJ-45 cable. 17. Power port To power the register, plug one end of the power cable to the register power port, and the other end to the wall.
User Manual – PayPoint Android Rev B UM600xxx Rev A, page 10 of 26 Power Press the register power button to turn the Elo PayPoint Register on. Press and hold power button when the register is on to bring up the Shut Down option screen. In the event that the register freezes and does not respond, press and hold the power button until the register turns off. If the register does not turn off via the power button, the register will need to be powered down by unplugging the power cord from the wall. The Elo PayPoint Register power button is equipped with an LED that indicates the power status of the register, as follows: Register Power Status LED Status OFF (disconnected from wall) Off OFF (connected to wall) Red SLEEP Red ON White The system consumes low power when in SLEEP and OFF modes. For detailed power consumption specifications, refer to technical specifications available on the Elo website www.elotouch.com. To bring register out of sleep/standby mode, press the power button once. If long periods of non-use are planned, turn off the Elo PayPoint Register to save power. The maximum voltage, frequency and current for the register, are provided in the power ratings table below: Operating Voltage Range Operating Frequency Range Operating Current Range Elo PayPoint Register 100 - 240Vac 50 – 60 Hz 0.1 – 0.3 Aac
User Manual – 2D Barcode Scanner UM600149 Rev. A, page 11 of 26 Section 3: Technical Support and Maintenance Information and guidance on how to use and operate your Elo PayPoint Register are available in this User Manual. Solutions to Common Problems Problem Suggested Troubleshooting The Elo PayPoint Register does not respond when turning on the system. Check that the power cable is properly connected to both the register and the wall. Power button LED will be red when register is properly connected to the wall. OR Unplug the power cable, re-plug after five seconds, and press the power button to turn on the system. OR In the case that the power button LED displays solid white light, which suggests that the system is on, there may be an issue with the display or LCD backlight. Please contact Elo Customer Service. Blank screen If the power button LED is blinking, the register may be in SLEEP mode. Press the power button to bring the unit our of SLEEP mode.
User Manual – 2D Barcode Scanner UM600149 Rev. A, page 12 of 26 Receipt printer does not print text on the receipt paper Ensure that the thermal receipt paper is installed in the printer in the proper orientation. Note: Only one side of the thermal paper is coated with the dye that changes color when heated. This is the side that will need to contact the printer thermal head. Refer to Chapter 8 for more information on how to properly install the thermal receipt paper in the receipt printer. OR Try and restart the register. Poor receipt printing quality Poor receipt printing quality may be due to the use of poor quality thermal paper. Refer to Chapter 8 for more information on recommended thermal paper for the Elo PayPoint Register receipt printer. Receipt printer does not run when it’s supposed to Push the receipt head release button, lift receipt printer head cover, and check that there is no paper jam. Clear any paper jam. MSR does not read card properly The MSR may not function properly when dirty. Use MSR cleaning cards (purchasable in some office supply stores). Cash drawer doesn’t open Check to ensure that cash drawer lock is not in lock position. OR Use the cash drawer manual release latch to open drawer.
User Manual – PayPoint Android Rev. B UM600xxx Rev A, page 13 of 26 Technical Assistance See this user manual’s last page for worldwide technical support phone numbers. Technical Specifications visit www.elotouch.com/products for technical specifications for this device Online Self-Help visit www.elotouch.com/go/websupport for online self-help Technical Support visit www.elotouch.com/go/contactsupport for technical support
User Manual – PayPoint Android Rev. B UM600xxx Rev A, page 14 of 26 Elo PayPoint Register Care and Handling The following tips will help maintain optimal performance of your Elo PayPoint Register:  Disconnect the power cable before cleaning.  To clean the unit (except for touch screen), use a soft cotton or microfiber cloth lightly dampened with a mild detergent.  It is important that your unit remains dry. Do not get liquids on or inside the unit. In the event that liquid does get inside, have a qualified service technician inspect the unit before you power it on again.  Do not wipe the screen with a cloth or sponge that could scratch the surface.  When cleaning the touchscreen, use window or glass cleaner applied to a clean cloth. Never apply the cleaner directly on the touchscreen. Do not use alcohol (methyl, ethyl or isopropyl), thinner, benzene, or other abrasive cleaners. Printer Maintenance Changing Printer Paper The register receipt printer operates using heat, and not with ink. Printer paper compatible with the Elo PayPoint receipt printer are as follows: Type: Thermal Paper (2 ¼ inches x 80 feet) Paper width: 2 ¼ inches (58 mm) Paper roll diameter: 1 7/8 inches (50 mm) (maximum) Paper length: 80 feet (24.4 m)
User Manual – PayPoint Android Rev. B UM600xxx Rev A, page 15 of 26 Printing width: 48mm To change the paper for the Elo PayPoint Register receipt printer: 1. Ensure that the register display head is flipped away from the receipt printer (in customer-facing view). 2. Push the receipt printer head release button to release the printer head cover. 3. Lift printer head cover. 4. Take out the roll of used printer paper, and replace with new roll of printer paper. Make sure that the paper is placed and positions in the correct orientation, as shown below.
User Manual – PayPoint Android Rev. B UM600xxx Rev A, page 16 of 26 Cleaning and Care of Printer The following tips will help maintain optimal performance of your Elo PayPoint Register receipt printer:  Do not pull any paper that is ejected from the printer.  Do not touch the printer roller or thermal head surface with bare hands. In the case of contact between printer roller or thermal head and hands, clean the roller and/or thermal head surface with alcohol, as specified in the latter parts of this section herein. Note: Contaminating heating elements with any oil or grease (e.g. oil from hands) may shorten the life of the thermal head.  Do not print when there is no receipt printer installed in the printer. Figure 4. View of receipt printer when printer head cover is open (left). View of the receipt printer according to the view denoted by the arrow. Prior to cleaning the PayPoint Register receipt printer, ensure that the register display head is flipped away from the receipt printer (in customer-facing view). Push the receipt printer head release button to release printer head cover and access the different printer components listed in Figure 4 above. Guidance on how to clean the printer photo-sensor, thermal head, and roller are as follows:
User Manual – PayPoint Android Rev. B UM600xxx Rev A, page 17 of 26 Roller 1.It is recommendable to clean the printer roller once a month. To do so: Apply isopropyl alcohol onto a cloth. a. Wipe off any stain from the printer roller with the alcohol dampened cloth. b. Use a dry soft cloth to wipe the roller. c. Wait to allow the roller to dry off, and then shut the printer head cover. d. Photo-sensor: 2.It is recommendable to clean the printer photo-sensor once a month. To do so: Use a Nylon brush (or equivalent) to brush off any paper dust or other residues that may be on the photo-sensor. a. Thermal head 3.It is recommendable to clean the printer thermal head once a month. To do so: Moist cotton swab with isopropyl alcohol. a. Wipe the thermal head with the cotton swab to remove any stain from the thermal head. b. Use a dry soft cloth to wipe the thermal head. c. Wait to allow the thermal head to dry off, and then shut the printer head cover. d.
User Manual – PayPoint Android Rev. B UM600xxx Rev A, page 18 of 26 Section 4: Safety Waste Electrical & Electronic Equipment Directive (WEEE) This product should not be disposed of with household waste. It should be deposited at a facility that enables recovery and recycling. Elo has put in place recycling arrangements in certain parts of the world. For information on how you can access these arrangements, please visit www.elotouch.com/e-waste-recycling-program/. CAUTION RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERY ACCORDING TO THE INSTRUCTION
User Manual – PayPoint Android Rev. B UM600xxx Rev A, page 19 of 26 Section 7: Regulatory Information Electrical Safety Information Compliance is required with respect to the voltage, frequency, and current requirements indicated on the manufacturer’s label. Connection to a different power source than those specified herein will likely result in improper operation, damage to the equipment or pose a fire hazard if the limitations are not followed. There are no operator serviceable parts inside this equipment. There are hazardous voltages generated by this equipment which constitute a safety hazard. Service should be provided only by a qualified service technician. Contact a qualified electrician or the manufacturer if there are questions about the installation prior to connecting the equipment to mains power. Emissions and Immunity Information Notice to Users in the United States: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. Notice to Users in Canada: This equipment complies with the Class A limits for radio noise emissions from digital apparatus as established by the Radio Interference Regulations of Industrial Canada. Notice to Users in the European Union: Use only the provided power cords and interconnecting cabling provided with the equipment. Substitution of provided cords and cabling may compromise electrical safety or CE Mark Certification for emissions or immunity as required by the following standards: This Information Technology Equipment (ITE) is required to have a CE Mark on the Manufacturer’s label
User Manual – PayPoint Android Rev. B UM600xxx Rev A, page 20 of 26 which means that the equipment has been tested to the following Directives and Standards: This equipment has been tested to the requirements for the CE Mark as required by EMC Directive 2014/30/ EU as indicated in European Standard EN 55032 Class A and the Low Voltage Directive 2014/35/EU as indicated in European Standard EN 60950-1. General Information to all Users: This equipment generates, uses and can radiate radio frequency energy. If not installed and used according to this manual the equipment may cause interference with radio and television communications. There is, however, no guarantee that interference will not occur in any particular installation due to site-specific factors. 1. In order to meet emission and immunity requirements, the user must observe the following: a. Use only the provided I/O cables to connect this digital device with any computer. b. To ensure compliance, use only the provided manufacturer’s approved line cord. c. The user is cautioned that changes or modifications to the equipment not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. 2. If this equipment appears to cause interference with radio or television reception, or any other device: a. Verify as an emission source by turning the equipment off and on. If you determine that this equipment is causing the interference, try to correct the interference by using one or more of the following measures: i. Move the digital device away from the affected receiver. ii. Reposition (turn) the digital device with respect to the affected receiver. iii. Reorient the affected receiver’s antenna. iv. Plug the digital device into a different AC outlet so the digital device and the receiver are on different branch circuits. v. Disconnect and remove any I/O cables that the digital device does not use. (Unterminated I/O cables are a potential source of high RF emission levels.) vi. Plug the digital device into only a grounded outlet receptacle. Do not use AC adapter plugs. (Removing or cutting the line cord ground may increase RF emission levels and may also present a lethal shock hazard to the user.) If you need additional help, consult your dealer, manufacturer, or an experienced radio or television technician.
User Manual – PayPoint Android Rev. B UM600xxx Rev A, page 21 of 26 Agency Certifications The following certifications and marks have been issued or declared for this peripheral: • FCC/IC • CE • UL/cUL/CB • China CCC • China SRRC - 5150-5250MHz for indoor use only - AT BE BG HR CY CZ DK EE FI FR DE EL HU IE IT LV LT LU MT NL PL PT RO SK SI ES SE UK FCC: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user‘s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. This equipment should be installed and operated to ensure a minimum of 20 cm spacing to any person at all times. IC: This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and
User Manual – PayPoint Android Rev. B UM600xxx Rev A, page 22 of 26 (2) This device must accept any interference, including interference that may cause undesired operation of the device. Le pré sent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisé e aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioé lectrique subi, mê me si le brouillage est susceptible d'en compromettre le fonctionnement." This equipment should be installed and operated to ensure a minimum of 20 cm spacing to any person at all times. This device for operation in the band 5150-5250MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems. RED: - Hereby, Elo declares that the radio equipment type, PayPoint, is in compliance with Directive 2014/53/EU. - The full text of the EU declaration of conformity is available at the following internet address: www.elotouch.com Explanation of Markings In accordance with the SJ/T11364 requirement, electrical and electronic products are marked with the following pollution control logo. The Environment-Friendly Use Period for this product is 10 years. The product will not leak or mutate under normal operating conditions listed below, so that the use of this electronic information product will not result in any severe environmental pollution, any bodily injury, or damage to any assets. Warning: This equipment is compliant with Class A of EN55032. In a residential environment this equipment may cause radio interference. This equipment should be installed and operated to ensure a minimum of 20 cm spacing to any person at all times. RF Frequency and maximum power Bluetooth : 11 dBm EIRP 2412MHz-2472MHz : 17 dBm EIRP 5150MHz-5250MHz : 18 dBm EIRP Operating Temperature: See chart below
User Manual – PayPoint Android Rev. B UM600xxx Rev A, page 23 of 26 Storage Temperature: See chart below It is encouraged and recommended that product packaging be recycled and reused according to local laws.
User Manual – PayPoint Android Rev. B UM600xxx Rev A, page 24 of 26 Power Specifications Electrical Ratings Input 100-240VAC Operating Conditions Temperature 0°C - 40°C Humidity 20% to 80% (non-condensing) Storage Conditions Temperature -20°C - 50°C Humidity 10% to 95% (non-condensing)
User Manual – 2D Barcode Scanner UM600149 Rev A, page 21 of 26 Section 5: Warranty Information For warranty information, go to http://support.elotouch.com/warranty/
User Manual – PayPoint Android Rev. B © 2016 Elo Touch Solutions, Inc. All rights reserved. Notes www.elotouch.com Visit our website for the latest • Product Information • Specifications • Upcoming Events • Press Releases • Software Drivers To find out more about our extensive range of Elo touch solutions, go to www.elotouch.com, or call the office nearest you. North America Tel +1 408 597 8000 Fax +1 408 597 8001 customerservice@elotouch.com Europe Tel +32 (0)16 70 45 00 Fax +32 (0)16 70 45 49 elosales@elotouch.com Asia-Pacific Tel +86 (21) 3329 1385 Fax +86 (21) 3329 1400 www.elotouch.com.cn Latin America Tel 786-923-0251 Fax 305-931-0124 www.elotouch.com

Navigation menu