Elo Touch Solutions ESY15I1 Touch All-in-One Computer User Manual aaio

Elo Touch Solutions, Inc. Touch All-in-One Computer aaio

User Manual

USER MANUAL Elo Touch Solutions ESY10i1 10.1” i-Series Interactive Signage ESY15i1 15.6” i-Series Interactive Signage ESY22i1 21.5” i-Series Interactive Signage SW602242 Rev A
User Manual: i-Series Interactive SignageSW602242 Rev A, Page 2 of 31 Copyright © 2014 Elo Touch Solutions, Inc. All Rights Reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, including, but not limited to, electronic, magnetic, optical, chemical, manual, or otherwise without prior written permission of Elo Touch Solutions, Inc. Disclaimer The information in this document is subject to change without notice. Elo Touch Solutions, Inc. and its Afffiliates (collectively "Elo") makes no representations or warranties with respect to the contents herein, and specifically disclaims any implied warranties of merchantability or fitness for a particular purpose. Elo reserves the right to revise this publication and to make changes from time to time in the content hereof without obligation of Elo to notify any person of such revisions or changes. Trademark Acknowledgments AccuTouch, CarrollTouch, Elo, Elo (logo), Elo Touch, Elo Touch Solutions, Elo TouchSystems, IntelliTouch, iTouch, SecureTouch, TouchTools and VuPoint are trademarks of Elo and its Affiliates. Windows is a trademark of Microsoft Corporation. Android is a trademark of Google Corporation.
User Manual: i-Series Interactive SignageSW602242 Rev A, Page 3 of 31 Table of Contents Chapter 1 – Introduction........................................................................... 4 Chapter 2 – Unpacking ................. ................. ............... ................ ............. 5 Chapter 3 – i-Series System Installation ............................................. 6 Chapter 4 – Mounting ................................................................................ 7 Chapter 5 – Operation ............................................................................... 10 Chapter 6 – Technical Support ............................................................... 23 Chapter 7 – Safety & Maintenance ........................................................ 24 Chapter 8 – Regulatory Information ................................................... 27 Chapter 9 – Warranty Information ......................................................... 30
User Manual: i-Series Interactive SignageSW602242 Rev A, Page 4 of 31 Chapter 1: Introduction Product Description Your new i-Series Interactive Signage system combines Elo Touch Solutions reliable performance with the latest developments in touchscreen technology and display design. This combination of features creates a natural flow of information between a user and the i-Series system. This i-Series system incorporates an active matrix thin-film-transistor, and LCD panel to provide superior display performance. Features that enhance this systems performance are PCAP touchscreen, Plug & Play compatibility, Micro-HDMI Out, LAN/Wifi and built-in speakers and headphone output capability. A general purpose input/output header is available and Bluetooth 4.0 is supported. Also 3G/4G LTE(Micro SIM card holder) support. Precautions Follow all warnings, precautions and maintenance as recommended in this user manual to maximize the life of your unit and prevent risks to user safety. See Chapter 8 for more information on i-Series system safety. This manual contains information that is important for the proper setup and maintenance of the i-Series. Before setting up and powering on your new system, read through this manual, especially the Installation, Mounting, and Operation chapters.
User Manual: i-Series Interactive SignageSW602242 Rev A, Page 5 of 31 Chapter 2: Unpacking Unpacking the i-Series Interactive Signage System 1. Carefully cut through the top piece of tape to open the top flaps. 2. Remove the top layer of the packaging pulp. a. The accessory box and the covered monitor will now be visible. 3. Lift the accessory box out of the packaging box to provide access to the required cables. 4. Remove the monitor from the box and set it down.
User Manual: i-Series Interactive SignageSW602242 Rev A, Page 6 of 31 Chapter 3: i-Series System Installation Connector Panel & Interfaces Check that the following items are present and in good condition:  i-Series system  Quick Install Guide  Power Brick  Cables o North America power cord o Europe power cord  Two (2) cable strain reliefs  Two (2) screws Remove the cable cover on the rear (when viewed in landscape orientation) to access the i-Series systems connector panel. i-Series System Connections to an External Computer Connect a Micro-HDMI cable between the system and the monitor.
User Manual: i-Series Interactive SignageSW602242 Rev A, Page 7 of 31 Chapter 4: Mounting General Mounting Information The monitor following the VESA pattern described in the following section. For optimal touch performance, ensure that the monitor is supported fully and is as flat as possible. The following three mounting orientations are supported: Landscape, portrait and table top mode. For optimal touch performance, ensure that the monitor is supported fully and is as flat as possible. Portrait
User Manual: i-Series Interactive SignageSW602242 Rev A, Page 8 of 31 Landscape Table Top Rear VESA Mount A four-hole 75x75mm (for 10.1”) and 100x100 (for 15.6”/21.5”) mounting pattern for M4 screws is provided on the rear of the monitor. Remove the stand using a Phillips screwdriver to access this mounting interface. The VESA FDMI-compliant counting is coded: VESA MIS-B, 75, C.
User Manual: i-Series Interactive SignageSW602242 Rev A, Page 9 of 31 10.1” 15.6”
User Manual: i-Series Interactive SignageSW602242 Rev A, Page 10 of 31 21.5”
User Manual: i-Series Interactive SignageSW602242 Rev A, Page 11 of 31 Chapter 5: Operation Power To turn the system on, press the power button once. If a power cable is plugged in to the i-Series system, then the i-Series system will turn on automatically. A Power Status LED is provided on the OSD Remote that functions according to the following table: i-Series System Status Color LED status OFF Orange OFF IDLE White BLINKING ON White ON The system consumes low power when in IDLE and OFF modes. For detailed power consumption specifications, refer to technical specifications available on the Elo website www.elotouch.com. Touching the screen will bring the system out of MONITOR IDLE mode. If long periods of disuse are planned, unplug the AC power cable to save power. The maximum voltage, frequency and current for the system are provided in the power ratings table below: Model Operating Voltage Range Operating Frequency Range Operating Current Range ESY10i1 100 - 240Vac 50/60 Hz 0.62A ESY15i1 100 - 240Vac 50/60 Hz 0.72A ESY22i1 100 - 240Vac 50/60 Hz 1.19A Operating System Android version 4.4 will be pre-loaded on the system. Projective Capacitance Touchscreens Technology Four (4) simultaneous touches can be reported at one time. Gesturing Images: For multi-touch monitors, the following gestures are possible: Dual Touch Gestures and their Functions: Swipe – The action of moving a finger across the screen.
User Manual: i-Series Interactive SignageSW602242 Rev A, Page 12 of 31 - The ability to swipe through from one picture to another or drag an icon Pinch-Zoom – Zoom into a picture - Place two fingers on the screen and move them closer together to zoom in. Move your fingers away from each other to zoom out. Before zoom After zoom Video An LCD panels native resolution is its width and height measured in number of pixels. In almost all cases, an image displayed on an LCD monitor will look best when your image resolution matches the LCD panels native resolution. 10.1” is 1280x800, 15.6” is 920x1080, 21.5” is 1920x1080. Physical Button Functionality Audio Earphone output with microphone input is supported. 3G/4G LTE module Information (Optional) Bands:  LTE (FDD) B1/B2/B3/B4/B5/B7/B8/B13/B17/B20  Penta-band DC-HSPA+/HSPA+/HSPA/UMTS B1/B2/B4/B5/B8  Quad-band EDGE/ GPRS/GSM 1900/1800/900/850 MHz Parameter Available Adjustment Power Button Turn on the system Home Button Returns to the Home page
User Manual: i-Series Interactive SignageSW602242 Rev A, Page 13 of 31 Data Transfer Rate:  WCDMA PS: UL (384 kbps)/ DL (384 kbps)  DC-HSPA+ :UL (11 Mbps)/ DL (42 Mbps)  LTE FDD: UL (50 Mbps)/ DL (100 Mbps) @Bandwidth 20M (CAT3)  GPRS/EDGE: Multi-slot Class 12 Support country list  US  Germany Wifi + Bluetooth The following protocols are supported for Wifi and Bluetooth:  Bluetooth 4.0+EDR Class 2, A2DP/ HID (Keyboard/Mouse), SPP(printer), Barcode scanner (HID/SPP) support.  IEEE 802.11b/g/n; WEP/WPA/WPA2 capable NFC Functionality (Optional) The following NFC protocols are supported:  ISO-14443-A  ISO-14443-B 1.1 Interfaces 1.1.1 RS232 and USB2.0 interfaces by use of corresponding cables. 1.1.2 USB 2.0 compliant interface configurable to support USB HID: Keyboard, or USB Virtual COM. 1.1.3 RS232 data output baud rate up to 115.2K BPS 1.2 Payment Applications 1.2.1 American Express ExpressPay 1.2.2 Discover ZIP 1.2.3 MasterCard PayPass/MCHIP 1.2.4 Visa MSD/qVSDC 1.2.5 Google wallet 1.2.6 ISIS wallet 1.3 MIFARE Applications 1.3.1 Read/Write of MIFARE Plus/Classic/Ultralight/DESFire cards 1.3.2 Support MIFARE higher baud rate up to 424KHz BCR Functionality (Optional) Incorporates proximity detector to activate Bar Code Scanner. Outstanding scanning performance up to 270 scans per second. Below are the supported Bar Code types and settings.
User Manual: i-Series Interactive SignageSW602242 Rev A, Page 14 of 31
User Manual: i-Series Interactive SignageSW602242 Rev A, Page 15 of 31 MSR Functionality (Optional) The MSR shall operate in keyboard mode. Capable of reading 3 tracks. Security level and Encryption function: OFF HDMI Output The HDMI(1920x1080P) output supports Elo monitor ET7001L/ET4201L/ET3201L/ET4243L/ET3243L. General Purpose Input/Output (GPIO) Support The i-Series supports a GPIO which can be used under the following conditions: Max Voltage: 5V Max Current: 200mA There are two input connections and one output connection. Pin 1 5 Volt output connection Pin 2  Input connection 1 Pin 3  Input connection 2 Pin 4 and Pin 5 are tied to ground Elo has a cable (PN # E086398) which extends this GPIO connection so that it is easy for users to connect their own peripherals. This cable can be found on the Elo website. Example Circuit
User Manual: i-Series Interactive SignageSW602242 Rev A, Page 16 of 31 GPIO PIN1 Software Section (Download SDK from www.elotouch.com) 1. Glossary 1.1. Abbreviation  SoC: System on a chip 1.2. Terms  IDLE_MODE: ELO specification for device interaction with POWER_KEY action  MSR: Magnetic Stripe Reader  BCR: Barcode Reader  NFC: Near Field Communication  ELOPeripheralService: The fundamental class to provide different functions for ELO application developmentEx 2. System Overview Fig 3-1 shows the software stack of Android system. This implementation based on Android design and extends the framework functionality at java services layer to fulfill customer requirement. The extended functionality at java service is named as “ELOPeripheralService” which provides the interfaces for application development.
User Manual: i-Series Interactive SignageSW602242 Rev A, Page 17 of 31 Fig 2-1. Android System Structure 2.1. Android Framework Java Service Based on developed programming language, Android services can be divided into native (C base) and java service. Android services are a kind of server-client structure where the server side can receive a request from the client and output the result to client. Also, the server-client structure can deal with synchronization issues from multi-client requests. Therefore, this framework ability, which forms the fundamental class “ELOPeripheralService,” is based on this kind of server-client design feature from Android. 2.2. ELOPeripheralService ELOPeripheralService is the major module to act client request from application layer. In order to complete the Android framework system design for service then below classes is added into system:  ELOPeripheralNative  Execution of some native-C function flows for ELOPeripheralService  ELOPeripheralManager
User Manual: i-Series Interactive SignageSW602242 Rev A, Page 18 of 31  Provides the interface to the application layer, which is the client component relative to ELOPeripheralService  EloPeripheralEventListener  Application extends abstract class to receive the driven event from EloPeripheralManager  Uses event driven notification method to notify the application program about the status change  IELOPeripheralService.aidl  Android programming language for java layer IPC communication  Used for Client-Server (ELOPeripheralManager-ELOPeripheralService) IPC communication where sending the application’s request to server side  IELOPeripheralServiceListener.aidl  Android programming language for java layer IPC communication  Used for server to notify the event driven status change to ELOPeripheralManager then ELOPeripheralManager will notify to application layer
User Manual: i-Series Interactive SignageSW602242 Rev A, Page 19 of 31 Figure 2-2. ELOPeripheralService 3. ELOPeripheralManager and ELOPeripheralEventListener As we mentioned at last section, ELOPeripheralManager and ELOPeripheralEventListener will be the component to provide interface for application development. Therefore, we provide the inner member data of ELOPeripheralManager and ELOPeripheralEventListener as below. 3.1. ELOPeripheralManager Inside this manager contains some inner class member as below and for each inner class provides specific functionality to peripheral equipment or defined action flow.
User Manual: i-Series Interactive SignageSW602242 Rev A, Page 20 of 31  public void registerListener(ELOPeripheralEventListener listener)  Provide interface for application to register the feedback structure instance  Needs to register before request (Activity life cycle: onResume)  public void unregisterListener(ELOPeripheralEventListener listener)  Provide interface for application to unregister the feedback structure instance  Needs to unregister before leave the application (Activity life cycle: onPause) 3.1.1. BCR  activeBCR  Activate the BCR device to reading the barcode data  BCR is active and successful reading the barcode sequence data then system by “ELOPeripheralEventListener” to notify application about the receiving data  disactiveBCR  Deactivate the BCR device reading action  isBCRDeviceConnected  Check the BCR device is connection with Android device or not
User Manual: i-Series Interactive SignageSW602242 Rev A, Page 21 of 31 3.1.2. GPIOs  pullHighGPIO  Pull high the state of GPIO-iface  PullLowGPIO  Pull low the state of GPIO-iface disactiveBCR  getGPIOInterfaces  Get the list string data of interest GPIOs at designed system.  Refer to Table 3-1 GPIOs list  Note:  The pull action only workable with output pin defined GPIO  The input pin defined GPIO can notify the application about the status change by “ELOPeripheralEventListener” also GPIOs PIN define gpio80 Output gpio81 Input gpio82 Input Table 3-1 GPIOs List 3.1.3. IDLE  activeIdleMode  Force system to enter IDLE_MODE (IDLE_MODE on)  disactiveIdleMode  Force system to leave IDLE_MODE (IDLE_MODE off) 3.2. ELOPeripheralEventListener
User Manual: i-Series Interactive SignageSW602242 Rev A, Page 22 of 31  onBCR_StateChange  Refer to Table 3-2  Notify the application about the BCR status change data  onGPIO_StateChange  Refer to Table 3-2  Notify the application about the GPIOs status change data BCR state value ELOPeripheralManager.BCR_STATE_DEVICE_CONNECTION 1 << 0 ELOPeripheralManager.BCR_STATE_DEVICE_DISCONNECTION 1 << 1 ELOPeripheralManager.BCR_STATE_DATA_RECEIVIED 1 << 2 ELOPeripheralManager.BCR_STATE_PIN_AUTO_DISABLE 1 << 3 GPIO state value ELOPeripheralManager.GPIO_STATE_HIGH 1 << 4 ELOPeripheralManager.GPIO_STATE_LOW 1 << 5 GPIO data gpio81 gpio82 Table 3-2
User Manual: i-Series Interactive SignageSW602242 Rev A, Page 23 of 31 Chapter 6: Technical Support If you are experiencing trouble with your i-Series system, refer to the following suggestions. If the problem persists, please contact your local dealer or contact Elo Touch Solutions Customer Service. Solutions to Common Problems Problem Suggested Troubleshooting The i-Series system does not respond when turning on the system. Disconnect the AC power cable and verify that the i-Series system is properly installed. Reconnect the AC power cable. Monitor display is blank. If the Power Status LED is blinking, the monitor or i-Series system may be in SLEEP mode. Press any key / move the mouse / touch the touchscreento see if the image reappears. To keep the system performing at an optimum level, follow the steps below: Usage duty cycle: 18 hours on per 24 hours Elo recommends using the Content Management System or O/S scheduling settings to manage duty cycle. This will enable power savings and trouble free operation throughout the life of the monitor. Technical Assistance Visit www.elotouch.com/go/websupport for online self-help. Visit www.elotouch.com/go/contactsupport for technical support. See this user manuals last page for worldwide technical support phone numbers.
User Manual: i-Series Interactive SignageSW602242 Rev A, Page 24 of 31 Chapter 7: Safety & Maintenance Safety To avoid risk of electric shock, follow all safety notices and do not disassemble the i-Series system. They are not user-serviceable. Do not block or insert anything inside any of the ventilation slots. The i-Series system is equipped with a 3-wire, grounding power cord. The power cord plug only fits into a grounded outlet. Do not fit or modify the plug into an outlet that has not been configured for this purpose. Do not use a damaged power cord. Only use the power cord that came with your Elo i-Series system. Use of an unauthorized power cord may invalidate your warranty. Ensure that the system is maintained and runs within the specified environmental conditions listed in the products specifications available on the Elo Touch Solutions website www.elotouch.com. Environmental Conditions for Transportation and Storage Temperature: Portrait and Landscape Mode: Operating 0°C to 40°C Storage/Transportation -20°C to 50°C Humidity (non-condensing) : Operating 20% to 80% Sto rage/Transportation 10% to 95% Altitude: Operating 0 to 3,658m Storage/Transportation 0 to 12,192m Caution RISK OF EXPLOSION IF BATTERY IS REPLACED WITH AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.
User Manual: i-Series Interactive SignageSW602242 Rev A, Page 25 of 31 Care and Handling The following tips will help maintain optimal performance of your i-Series system:  Disconnect the AC power cable before cleaning.  To clean the display, use a cloth lightly dampened with a mild detergent.  It is important that your unit remains dry. Do not get liquid on or inside the unit. In the event that liquid does get inside, have a qualified service technician inspect the unit before you power it on again.  Do not wipe the screen with a cloth or sponge that could scratch the surface.  When cleaning the touchscreen, use window or glass cleaner applied to a clean cloth or sponge. Never apply the cleaner directly on the touchscreen. Do not use alcohol (methyl, ethyl or isopropyl), thinner, benzene, or other abrasive cleaners. Waste Electrical & Electronic Equipment Directive (WEEE) This product should not be disposed of with household waste. It should be deposited at a facility that enables recovery and recycling. Elo has put in place recycling arrangements in certain parts of the world. For information on how you can access these arrangements, please visit http://www.elotouch.com/AboutElo/ewaste-program/.
User Manual: i-Series Interactive SignageSW602242 Rev A, Page 26 of 31 Chapter 8: Regulatory Information I. Electrical Safety Information: Compliance is required with respect to the voltage, frequency, and current requirements indicated on the manufacturer’s label. Connection to a different power source than those specified herein will likely result in improper operation, damage to the equipment or pose a fire hazard if the limitations are not followed. There are no operator serviceable parts inside this equipment. There are hazardous voltages generated by this equipment which constitute a safety hazard. Service should be provided only by a qualified service technician. Contact a qualified electrician or the manufacturer if there are questions about the installation prior to connecting the equipment to mains power. II. Emissions and Immunity Information Notice to Users in the United States: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Notice to Users in Canada: This equipment complies with the Class A limits for radio noise emissions from digital apparatus as established by the Radio Interference Regulations of Industrial Canada. CAN ICES-3(A)/NMB-3(A) This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired
User Manual: i-Series Interactive SignageSW602242 Rev A, Page 27 of 31 operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement." FCC RF Exposure Compliance: This equipment complies with radio frequency (RF) exposure limits adopted by the Federal Communications Commission for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body. IC RF Exposure Compliance: This equipment complies with IC RSS-102 RF exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body. Déclaration d'exposition aux radiations: Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps. Notice to Users in the European Union: Use only the provided power cords and interconnecting cabling provided with the equipment. Substitution of provided cords and cabling may compromise electrical safety or CE Mark Certification for emissions or immunity as required by the following standards: CE RF Exposure Compliance: This device meets the EU requirements (1999/519/EC) and the International Commission on Non-Ionizing Radiation Protection (ICNIRP) on the limitation of exposure of the general public to electromagnetic fields by way of health protection. General Information to all Users: This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body. This Information Technology Equipment (ITE) is required to have a CE Mark on the Manufacturer’s label which means that the equipment has been tested to the following Directives and Standards: This equipment has been tested to the requirements for the CE Mark as required by EMC Directive 2004/108/EC as indicated in European Standard EN 55022 Class A and the Low Voltage Directive 2006/95/EC as indicated in European Standard EN 60950-1. General Information to all Users: This equipment generates, uses and can radiate radio frequency energy. If not installed and used according to this manual the equipment may cause
User Manual: i-Series Interactive SignageSW602242 Rev A, Page 28 of 31 interference with radio and television communications. There is, however, no guarantee that interference will not occur in any particular installation due to site-specific factors. 1) In order to meet emission and immunity requirements, the user must observe the following: a) Use only the provided I/O cables to connect this digital device with any computer. b) To ensure compliance, use only the provided manufacturer’s approved line cord. c) The user is cautioned that changes or modifications to the equipment not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. 2) If this equipment appears to cause interference with radio or television reception, or any other device: a) Verify as an emission source by turning the equipment off and on. If you determine that this equipment is causing the interference, try to correct the interference by using one or more of the following measures: i) Move the digital device away from the affected receiver. ii) Reposition (turn) the digital device with respect to the affected receiver. iii) Reorient the affected receiver’s antenna. iv) Plug the digital device into a different AC outlet so the digital device and the receiver are on different branch circuits. v) Disconnect and remove any I/O cables that the digital device does not use.(Unterminated I/O cables are a potential source of high RF emission levels.) vi) Plug the digital device into only a grounded outlet receptacle. Do not use AC adapter plugs. (Removing or cutting the line cord ground may increase RF emission levels and may also present a lethal shock hazard to the user.) If you need additional help, consult your dealer, manufacturer, or an experienced radio or television technician. III. Agency Certifications The following certifications and marks have been issued or declared for this monitor: United States FCC, UL CB (International) Canada CUL, IC Europe CE Explanation of Markings (1). In accordance with the SJ/T11364-2006 requirement, the electronic information products are marked with the following pollution control logo. The Environment-Friendly Use Period for
User Manual: i-Series Interactive SignageSW602242 Rev A, Page 29 of 31 this product is 10 years. The product will not leak or mutate under normal operating conditions listed below, so that the use of this electronic information product will not result in any severe environmental pollution, any bodily injury, or damage to any assets. Operating Temperature:0-40 / Humidity:20%-80% (non-condensing). Storage Temperature:-20~60 / Humidity:10%~90% (non-condensing). (2). It is encouraged and recommended that this product be recycled and reused according to local laws. The product should not be thrown away casually.
User Manual: i-Series Interactive SignageSW602242 Rev A, Page 30 of 31 Chapter 9: Warranty Information For warranty information, go to http://www.elotouch.com/Support/warranty.asp
User Manual: i-Series Interactive SignageSW602242 Rev A, Page 31 of 31 Check out our website www.elotouch.com Get the latest...  Product Inf ormation  Specifications  Upcoming events  Press re leases  Software drivers Getting in Touch with Us To find out more about the extensive range of Elo touch solutions, visit our website at www.elotouch.com, or simply call the office nearest you: Copyright 2014 Elo Touch Solutions, Inc. All rights reserved North America Europe Asia-Pacific Latin America Elo Touch Solutions 1033 McCarthy Blvd Milpitas, CA 95035 Tel 800-ELO-TOUCH Tel + 1 408 597 8000 Fax +1 408 597 8001 customerservice@elotouch.com Tel +32 (0) 16 70 45 00 Tel +86 (21) 3329 1385 Tel 786-923-0251 Fax +32 (0)16 70 45 49 Fax +86 (21) 3329 1400 Fax 305-931-0124 elosales@elotouch.com www.elotouch.cn www.elotouch.com.ar

Navigation menu