Electronics PA-PK Self-Contained Door Lock User Manual Manual

International Electronics Inc. Self-Contained Door Lock Manual

Manual

Installation Instructions For Low Profile Mortise LockA7454A
Table of ContentsWarning .......................................................1General Description .........................................2Specifications ................................................2Parts Breakdown............................................3-5Features.......................................................5Installation Instructions...................................6-13Operational Check ..........................................14Basic Programming Instructions .........................14Keypad Only (100 Users–LK) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15Keypad or Proximity/Keypad (500 Users–LU or PK). . . . . . . . . . . . . . . 18Proximity Only (500 Users–PA). . . . . . . . . . . . . . . . . . . . . . . . . . . . 22Chain Programming ........................................23Transaction Log .............................................241234567Page9810
1This device complies with Part 15 of the FCCRules. Operation is subject to the following twoconditions: (1) this device may not cause harmfulinterference, and (2) this device must accept anyinterference received, including interference thatmay cause undesired operation.Note: This equipment has been tested and foundto comply with the limits for a Class B digitaldevice, pursuant to Part 15 of the FCC Rules.These limits are designed to provide reasonableprotection against harmful interference in a residential installation. This equipment generates,uses and can radiate radio frequency energy andif not installed and used in accordance with theinstructions, may cause harmful interference toradio communications. However, there is no guarantee that the interference will not occur in a particular installation. If this equipment doescause harmful interference to radio or televisionreception, which can be determined by turningthe equipment off and on, the user is encouragedto try to correct the interference by one or moreof the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipmentand receiver.• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.• Consult the dealer or an experienced TV technician for help.This Class B digital apparatus complies withCanadian ICES-003Cet appareil numÈrique de la classe B est conforme ‡ la norme NMB-003 du CanadaWarning1Warning: Changes or modifications to thisunit not expressly approved by the partyresponsible for compliance could void theuser's authority to operate the equipment.
2• Latchbolt - Stainless Steel• Deadbolt - Stainless Steel• Guardbolt - Stainless Steel, non handed• Handed - Easily field reversible without disassembling the lock body• Case - 12 gauge heavy duty wrought steel• Outside lever controlled by Keypad, Keypad/Prox or Prox only• Inside lever retracts latchbolt and deadbolt• Locks furnished for 1 3/4" doors. Can be furnished for other door sizes upon request. Consult factory• U.L. Listed (3 hr.)3SpecificationsGeneral Description2The SARGENT Keypad Mortise Lock/Prox is designed for areas which require authorized entry.It is a self-contained microprocessor-controlled keypad with non volatile solid-state memory. Thekeypad will hold a total of 100(LK) / 500(LU, PK, PA) different User Codes. User Codes “01”,“02”, and “03” are utilized for Master Code, Emergency Code, and Supervisory Code, respectively. This product is operated by six (6) “AA” Duracell Alkaline Batteries. SARGENT mortise locks aredesigned with high quality components to provide the high security, performance and durability. Warning!To comply with “Fire Listed” doors, the batteries must be replaced with Alkaline batteries only.
3Parts Breakdown 4111127/2829543721617 15148915312122 202018/1925232426212226161173013131224’A’ DESIGN (LH) ’A’ DESIGN (RH) ’B’ DESIGN’E’ DESIGN ’F’ DESIGN ’H’ DESIGN ’J’ DESIGN ’L’ DESIGN ’P’ DESIGN ’W’ DESIGN33
4Item # Part# Description # Required1 82-3846 Outside Escutcheon with Cylinder Hole and Key Pad, or Key Pad / Prox 182-3847 Outside Escutcheon without Cylinder Hole and Key Pad or Key Pad / Prox 182-3848 Outside Escutcheon with Cylinder Hole and Prox Only 182-3849 Outside Escutcheon without Cylinder Hole and Prox Only 182-0493 Outside Escutcheon Housing Only with Cylinder Hole 182-0495 Outside Escutcheon Housing Only without Cylinder Hole 152-2431 Proximity Circuit Board and Harness Assembly 152-2432 Key Pad / Proximity Circuit Board and Harness Assembly 12 82-3837 Inside Escutcheon with Thumb Turn and 100 User Controller 182-3838 Inside Escutcheon without Thumb Turn and 100 User Controller 182-3839 Inside Escutcheon with Thumb Turn and 500 User Controller 182-3840 Inside Escutcheon without Thumb Turn and 500 User Controller 182-3841 Inside Escutcheon with Thumb Turn Prox / Key Pad Controller 182-3842 Inside Escutcheon without Thumb Turn Prox / Key Pad Cont. 182-0492 Inside Escutcheon Housing Only without Thumb Turn 182-0494 Inside Escutcheon Housing Only with Thumb Turn 152-2440 100 (LK) User Key Pad Controller Assembly 152-2447 500 (LU, PK) User Key Pad Controller Assembly 152-2454 Key Pad / Proximity (PK), Proximity Only (PA) Controller Assembly 13 52-2437 Battery Cover Assembly 14 01-1212 Security Screw 15 01-0297 Security Tool 17 82-0507 Thumb Turn 18 77-0772 Spindle (Thumb Turn) 19 01-0844 Washer (Thumb Turn) 110 01-0543 Spring Grip Fastener (Thumb Turn) 111 77-0168 Thru Bolts #8-32 x 1 7/8” Flat Head Screw 212 52-0033 Fire Stop Plate 113 01-1500 Fire Stop Screws #8 x 1/2” Type “AB” Phillips Pan Head Self Tap 214 82-3088 Inside Spindle Adapter & Plate Assembly 115 01-1495 Screw #8-32 x 1/2”216 82-0368 Inside Spindle / Outside Spindle 217 82-0347 Inside Spring / Outside Spring 218 82-0081 Face Plate no Dead Bolt 119 82-0084 Face Plate with Dead Bolt 120 01-1028 Face Plate Screws Machine 8-32 x 1/4”221 01-2299 Lock Body Screws / Wood Door #12 x 1 1/4”222 01-1019 Lock Body Screws / Metal Door 12-24 x 1/2”223 82-0184 Cap Nut 124 01-0079 Washer 225 82-3082 Plate Assembly 126 81-0723 Post 227 01-1472 Lever Handle Screw, A, E & F Lever 128 01-1174 Lever Handle Screw, B, J, L, P & W Lever 129 81-0467 Inside Lever (L.H.) "A" Design 181-0468 Inside Lever (R.H.) "A" Design 181-0490 Inside Lever "B" Design 181-0470 Inside Lever "E" Design 181-0471 Inside Lever "F" Design 181-0447 Inside Lever "J" Design 1 81-0489 Inside Lever "L" Design 181-0513 Inside Lever "P" Design 181-0445 Inside Lever "W" Design 1Parts Breakdown (Continued)
55Features•Non volatile memory•Motor driven, battery operated mortise lock•Battery operated with 6 each “AA” Alkaline •Low battery alert–4 chirps after code entry•External remote “request to exit” connector•Supervisory code will unlock door when lowbattery had expired•100 (LK) or 500 (LU, PK, PA) users total•Programming done at keypad or with Soflink™Plus software and a PC (LU, PA, PK). Soflink™Plus Software User Manual A7462•Proximity FOB or Card optional•Operates utilizing any two to six digits per code. Digits may be repeated and codes maystart with zero•Cylinder override optional•Entry of three wrong User Codes disables all codes for ten seconds. Yellow LED on solid•Piezo horn can be heard with each keystroke or turned off by Master or Supervisory Code•Last 15 (LK) transactions can be output to portable printer via infrared link•Last 1000 (LU, PK, PA) transactions can beoutput to portable printer via infrared link or PC via Soflink™Plus software•Deadbolt switch inside mortise lock allowsEmergency Code and Master Code holdersto gain entry when deadbolt is thrownItem # Part# Description # Required30 82-0151 O/S Lever Handle R.H. "A" Design 182-3074 O/S Lever Handle R.H. "A" Design Stainless Steel 182-0152 O/S Lever Handle L.H. "A" Design 182-3073 O/S Lever Handle L.H. "A" Design Stainless Steel 182-0153 O/S Lever Handle "B" Design 182-0154 O/S Lever Handle "E" Design 182-3074 O/S Lever Handle "E" Design Stainless Steel 182-0155 O/S Lever Handle "F" Design 182-3076 O/S Lever Handle "F" Design Stainless Steel 182-3079 O/S Lever Handle "H" Design 182-0156 O/S Lever Handle "J" Design 182-0157 O/S Lever Handle "L" Design 182-0158 O/S Lever Handle "P" Design 182-0159 O/S Lever Handle "W" Design 131 82-3732 Lockbody Assembly (with deadbolt) (8276 & 8277) 182-3733 Lockbody Assembly (without deadbolt) (8278 & 8279) 132 01-0803 Battery Alkaline ("AA" cell) 633 52-0253 Battery Keeper 1Parts Breakdown (Continued)
6Installation Instructions6Left HandHinges Left.Open inward."LH"Left HandReverse BevelHinges Left.Open Outward"LHRB"Right HandHinges RightOpen Inward."RH"Right HandReverse BevelHinges Right.Open Outward."RHRB"• View lock body from top and from the outside (as shown above)BevelLatchbolt Right Hand Right HandReverse BevelLeft HandReverse BevelLock Body • Verify hand and bevel of doorConnector and WiresDeadboltGuardboltLatchboltFrontTopLock w/cylinderOverride(Shown)End Cap
7Outside of DoorInside of DoorOutside Cylinder HoleLever Handle HoleMortisedareaPre-drilled and /orTapped Holes 2 placesThrubolt holeThrubolt holeInside Cylinder Hole Lever Handle HoleThumb TurnLever HoleNOTE: Always consult the proper template prior to drilling any holes.Hole for ribboncable from controller to keypad Installation Instructions (Continued)Door Preparation
8Installation Instructions (Continued)How to Reverse Lock HandREDMUST Right HandShownOutside of Door
9Installation Instructions (Continued)Step #1 Installation of Lockbody/Attaching Lockbody ScrewsInside of Door(2) #12-24 x 1/2" longFlat Head Screwfor metal doors(2) #12 x 1 1/4" longFlat Head Wood Screwfor wood doors• Wires and Connector go into the mortised area and out of the inside cylinder hole• Insert Lockbody in mortised cutout• Hold loosely in place with (2) Lockbody screws• DO NOT TIGHTEN SCREWS AT THIS TIMEMUST feed Connector & Wires thrunon-cylinderside.
10Installation Instructions (Continued)Step #2 Attaching of Fire Stop PlateOutside of DoorCL Of 1 1/2" Dia(2) Self Tapping Screws #8 x 1/2" long for wood & metal doors(2) 1/8" Dia holes required7"81"2Slot1NOTE: Fire stop plate is required on all fire rated doors
11Outside of DoorMortise lockbody connector and wire*8-32 Flat HeadScrewKeypad/prox connector and cableFrom the outside of the door, feed wires and connector through fire stop plateTo secure the adapter and plate assembly to the inside of the door, thread the screws mounting posts of the outside lever assembly. Tighten retaining nut by hand.Back off retaining nut slightlyuntil star pattern lines up with square lever assembly cornersInsert Spindle into square hole on inside of door.With outside lever horizontal, carefully insert the mounting posts through the door and lockbody. Make sure the spindle is properly engaged in the lock.NOTE: For installation of optional gasket Part #82-0500 see Gasket InstallationLocate (2) #8-32 Flat Head Screw and insert through the escutcheon into the outside escutcheon. Tighten firmly.Plug Keypad Connectorinto inside Escutcheonas shown. Place excessivewire in hole.Plug smaller Connectoras shown into the insideEscutcheon. Place excessive wire in inside escutcheon assembly. Keep excessive wires away from cylinder hole.NOTE:Both connectors go ononly one way. Do notoffset the connectors.Be sure connectors areseated completely.If not seated, Keypad will not function properly.Installation Instructions (Continued)Step #3 Installation of Outside/Inside Escutcheon & Lever Assembly
12Installation Instructions (Continued)Step #4 Installation of Inside Lever/Outside CylinderSARGENTSARGENTNote: Key and the cylinder must be rotated as shownCorrect WrongVery Important•Slide lever handle onto spindle until fully seated. Be sure handle is horizontal and facing to the rear of door•Tighten the set screw securely with 1/8" hex wrench•Put the turn leverin the up position•Align cylinder •Screw cylinder lockbody unit•Tighten the set screw to preventunscrewing of the cylinder•Turn the key way in the cylinder to make certain that the locking or latching mechanism function correclly.Outside of DoorType 43 MortiseCylinder ONLYKeyInside of Door•Set ScrewInside LeverPhillips screwdriverSet screw

Navigation menu