Eastman Kodak 81507E2537 8150 DryView Laser Imager Low Power Transmitter User Manual 7

Eastman Kodak Company 8150 DryView Laser Imager Low Power Transmitter 7

Contents

user guide 2

September 30, 2004 7F3319 3-13 TroubleshootingCorrecting ErrorsOccasionally errors (malfunctions), such as film jams, may occur in the imager during print operations. You can easily correct minor problems. If more serious malfunctions occur, you should contact a trained Authorized Service Provider of Kodak products (see “Calling for Support” on page 3-17).Error and Alarm Indications The Imager can detect malfunctions and other conditions that require operator action. The Local Panel reports the presence of these errors or abnormal conditions in several ways:•Error Message screen•Current Errors screen•Current Errors notice on the Home screen•Home screen status messagesHome Screen Status MessagesFor a description of the status information reported on the Home screen, see “Home Screen Status Line” on page 2-14. Most of these status messages do not report errors or abnormal conditions, but they do give information about the current state of the Imager that may be useful for troubleshooting.Status information about the film supply and film tray is displayed within the Film Tray button on the Home screen. For a description, refer to “Film Supply Button Status Information” on page 2-12.
3-2 7F3319 September 30, 2004TroubleshootingError Message Screen The Error Message screen is the main error reporting mechanism for the Imager. When the Imager detects an error, an alarm sounds and the Local Panel displays an Error Message screen that describes the error and gives a corrective action. Touch anywhere on the screen to silence the alarm.Error Message Screen642315Error Message Screen Details1 Error Code. Identifies the type of error. Refer to this code when calling for service.2 Open Door button. Unlatches the front door. This button will appear when the front door must be opened to correct the reported error. 3X button. Closes the Error Message screen and moves to the Current Errors screen, which lists any uncorrected errors in the Imager. (See “Current Errors Screen” on page 3-4.) If you have not corrected the error when you press X, the error will be listed on the Current Errors screen.4 System Info button. Opens the System Information menu screen. (See “System Information Menu” on page 2-26.)5 Play Video button. Plays a short video that explains how to correct the error. A video is not available for all errors.6 Date and Time. When the error occurred.
TroubleshootingSeptember 30, 2004 7F3319 3-3NOTE: If you close an Error Message screen without correcting the current error, you can recall the Error Message from the Current Errors screen. (See “Current Errors Screen” on page 3-4.)Operator Action When an error message is displayed:1. Silence the alarm by touching anywhere on the Error Message screen.2. Perform the corrective action recommended on the screen. If this does not clear the error, call for service. (See “Calling for Support” on page 3-17.)Note the error code and error message before you call for service.The error message may direct you to perform one of the following actions:• Restart the Imager.1. Go to the Home screen.2. Press the Power Off button.3. Wait for the Local Panel to go blank.4. Turn off the power switch on the back of the Imager and then turn it back on.• Open the front door manually. See “Opening the Front Door Manually” on page 2-49.• Close the film cartridge. See “Manually Closing the Film Cartridge” on page 3-9.
3-4 7F3319 September 30, 2004TroubleshootingCurrent Errors Screen The Current Errors screen shows a list of uncorrected errors in the Imager. To display this screen:1. Press the Menu button.2. On the Main Menu screen, press Current Errors.The Current Errors screen appears:Current Errors ScreenTo see detailed information about any of the errors:1. Highlight the error using the Up or Down arrow.2. Touch Select.The Error Message screen displays the error message for the error you selected. (See “Error Message Screen” on page 3-2.)List of Errors
TroubleshootingSeptember 30, 2004 7F3319 3-5Current Errors Notice on theHome ScreenWhen there are one or more uncorrected errors in the Imager, the Home screen displays a Current Errors notice that shows the number of uncorrected errors in the Imager.To see a list of the current errors, you can display the Current Errors screen. (See “Current Errors Screen” on page 3-4.)Home ScreenCurrent ErrorsNotice
3-6 7F3319 September 30, 2004TroubleshootingCalibration FailurePeriodically the Imager must be calibrated to ensure that internal settings match the characteristics of the film in the Imager. Calibration is performed by running a calibration print. The Imager runs a calibration print when:• A film cartridge containing film with new sensitometric characteristics (speed, contrast) is loaded.• The Imager has not printed film for 7 days.• The Dpatch (density patch) printed on the film is out of range.The operator can also request a calibration print from the Local Panel. For more information on calibration, see “Running a Calibration Print” on page 2-53.Occasionally, the Imager may fail calibration. When this occurs, the Local Panel displays an error message screen. Depending on the cause of the calibration failure, the Imager may or may not be able to continue operating.There are four conditions that cause calibration failure. The four error message screens, below and on the next page, describe these error conditions and show recommended operator actions.These two errors indicate possible film aging. You can elect to continue operation with the current film by touching Yes on the error screen.
TroubleshootingSeptember 30, 2004 7F3319 3-7These two calibration errors indicate a major machine or film fault. The Imager cannot continue to operate with the current film.If you cannot restore normal operation by following the recommended action on the error message screen, call for service. (See “Calling for Support” on page 3-17.)
3-8 7F3319 September 30, 2004TroubleshootingFilm Transport ProblemsThe illustration below shows the path that film travels through the Imager after the operator requests a print. The numbers in the illustration identify key areas on the path through the five major areas in the Imager:Area 1 – Film pickup from the cartridgeArea 2 – Film feed into the exposure areaArea 3 – Film feed out of the exposure areaArea 4 – Film feed into the processorArea 5 – Film feed out of the processor and into the film trayFilm Drive PathH188_1063GC
TroubleshootingSeptember 30, 2004 7F3319 3-9Films may occasionally jam at various points along the film path. When a film jam or film feed error occurs, an error message appears. The error message identifies the area where a jam has occurred and recommends a corrective action. The following information supplements the advice given in the error messages for film feed problems.Manually Closing the Film CartridgeWhen clearing film jams you may have to close the film cartridge manually. Normally the Imager automatically closes the film cartridge when you press the Open Front Door button. When a film jam occurs, the Imager may be unable to close the cartridge. The front door then will not open.When the film cartridge fails to close, an error message appears. Press the Door Open button on the Error Message screen to unlock the front door. NOTE: If you open the front door when the film cartridge is open, the top sheets of film in the cartridge are exposed. Before opening the door, make the room as dark as possible to minimize exposure.Manually Closing the Film Cartridge1. Darken the room.2. Open the front door.H200_0004daFilm Path(dashed line)RollbackKnob
3-10 7F3319 September 30, 2004Troubleshooting3. Clear any films that may be jammed in the film cartridge area.4. Turn the rollback knob counterclockwise to close the cartridge.Film Pickup Problems in Area 1Area 1 is the location where film is removed from the film cartridge and positioned to be sent by drive rollers toward the exposure area. If the Imager cannot properly pick up a sheet of film and position it for drive, error 21-116 (Pickup Fail) is declared. Error 21-177 (Cartridge Failed to Close) also relates to Area 1.NOTE: When problems occur in Area 1, the film cartridge is left open. When you open the front door, the top sheets of film in the cartridge will be exposed. Before opening the door, make the room as dark as possible to minimize exposure.Film Area 11. Press Door Open on the Error Message screen.2. Remove any film outside the cartridge.3. Turn the rollback knob counterclockwise to manually close the cartridge lid.4. Close the front door.5. If you cannot resolve the problem, call for service. (See page 3-17.)H200 0005dRollbackArea 1Knob
TroubleshootingSeptember 30, 2004 7F3319 3-11Removing Film Jams from Area 2Area 2 in the Imager includes the path between the film pickup assembly and the exposure platen.NOTE: When jams occur in Area 2, the film cartridge is left open. When you open the front door, the top sheets of film in the cartridge will be exposed. Before opening the door, make the room as dark as possible to minimize exposure.Jam Area 21. Press Door Open on the Error Message screen. 2. Remove the jammed film.3. Turn the rollback knob counterclockwise to manually close the cartridge lid.4. Close the front door.H200_0006daRollback KnobFilm PickupAssemblyExposurePlatenArea 2
3-12 7F3319 September 30, 2004TroubleshootingRemoving Film Jams from Area 3Area 3 includes the exposure platen. Jams in this area occur as film is entering the platen before exposure, or as film is leaving the platen after exposure. In rare cases, film may stall in the transport area above the platen.Jam Area 31. Open the front door.NOTE: When film jams in this area, the cartridge may not close. If it does not close, the front door will not unlock normally. You may have to open the door manually (see “Opening the Front Door Manually” on page 2-49). When the front door opens, the top sheets of film in the cartridge will be exposed. Before opening the door, make the room as dark as possible to minimize exposure.2. If the film cartridge is open, turn the rollback knob counterclockwise to manually close the cartridge lid.3. Clear the jammed film, if it is accessible.4. If the film is not accessible:a. Open the platen door by sliding the door latch to the left and pulling out the platen door.H200_0007daPlaten DoorLatchPlastic ThumbTab 1Plastic ThumbTab 2VerticalTransportPlaten FeedRollersArea 3ExposurePlaten
TroubleshootingSeptember 30, 2004 7F3319 3-13b. Push the optics module toward the rear of the imager slowly and smoothly.c.Clear the film from inside the platen. If film is caught in the platen feed rollers, pull Plastic Thumb Tab 1 (inside the platen door) to the right. This opens the rollers and frees the film.d. After clearing the jam, close the platen door.5. If film is stalled in the vertical transport area, pull Plastic Thumb Tab 2 in this area to the right to open the rollers and free the film.6. Close the front door.OpticsModule10 cm (4 in.)
3-14 7F3319 September 30, 2004TroubleshootingRemoving Film Jams from Area 4Area 4 includes the film processor.When a jam occurs in this area all films in the Imager must be removed.Jam Area 41. Open the hood.CAUTION:Drum and rollers inside the processor are hot. Exercise caution when removing jammed film from the processor.2. Release the two clamps at the left of the processor and open the drum cover. (See the following figure).CAUTION:To prevent damage to the surface of the processor drum, do not use any type of tool to remove jammed film.H200_0008daProcessorDrumArea 4Plastic ThumbTab
TroubleshootingSeptember 30, 2004 7F3319 3-15Opening the Drum Cover3. Clear the jammed film from the processor area (there may be more than one sheet). If film is jammed in the drive rollers, pull the Plastic Thumb Tab to the left to open the rollers and free the film.4. Close the drum cover and secure it with the two clamps.5. Remove any films in Area 5. (See page 3-16.)6. Open the front door.7. Remove all films in the lower part of the Imager.8. Close the front door.9. Close the hood. The processor will have to warm to operating temperature before the imager can resume printing.OpenClampsPlastic ThumbTabOpen DrumCover
3-16 7F3319 September 30, 2004TroubleshootingRemoving Film jams from Area 5Area 5 consists of the components between the processor drum and the film exit tray. Jams can occur in this area between the drum and the densitometer, or in the densitometer. See the figure below.When a jam occurs in this area all films in the imager must be removed.Jam Area 51. Open the hood.CAUTION:Drum and rollers inside the processor are hot. Exercise caution when working in the drum area.2. Clear the jammed film from the processor area (there may be more than one sheet). If film is jammed in the drive rollers, pull the Plastic Thumb Tab to open the rollers and free the film.H200_0009daDensitometerPlastic Thumb TabsExit TrayProcessorDrumArea 5
TroubleshootingSeptember 30, 2004 7F3319 3-173. Remove any films in the processor. (See page 3-14.)4. Close the hood.5. Open the front door.6. Remove all films in the lower part of the Imager.7. Close the front door.The processor will have to warm to operating temperature before the imager can resume printing.Calling for SupportIf you cannot correct a malfunction and need help, call for support (see the following table). Before you call, have the following information ready:• Model number: 8150 • K-number: Displayed on the Local Panel System Information Screen• Error code and error message if they are displayed on the Local PanelService Phone NumbersCountry Phone NumberArgentina 54-3327-458-19554-3327-458-163Austrailia 1 800 034 4871 800 805 290Austria 43.800291332Azerbaijan 00 99412 410856Belgium 32.27194116Bolivia 54-3327-458-19554-3327-458-163Brazil 0800 15003Canada 1-800-268-1567Peoples Republic of China 800 820 5800Cyprus 00 352 497777
3-18 7F3319 September 30, 2004TroubleshootingCzech Republic 420 236 100 307420 62 335 426Denmark 45 70206129Finland 35.88001214France 01 4001 4705Germany 49.0180.3000.307India 1600 118989Iran 00 98 216 95082100 98 216 40210500 98 21 256 974100 98 21 256 9097Ireland 44.01442 845775Israel 00 972 3 9254040Italy 39.02.66028000Japan0120-45-1881Jordan 00 962 6 454584500 962 6 4543354Netherlands 31.347.363900Norway 47.66 81 80 80Pakistan 00 92 21 2638881Palistinian Territory 00 970 92387421Paraguay 54-3327-458-19554-3327-458-163Portugal 351 21 414 7642 Qatar 00 974 4469 83000 974 4360 820Service Phone NumbersCountry Phone Number
TroubleshootingSeptember 30, 2004 7F3319 3-19Romania 00 40 1210 3854Saudi Arabia 00 966 2 682 821900 966 1 464 5064Spain 902 19 03 99Sweden 46.200.119.494Switzerland 41.0800.804807Syria 00 963 112128600Tajikistan 00 90 216 578 2600Turkey 90 216 572 54 33Turkmenistan 00 90 216 578 2600United Arab Emirates 00 971 6 746 675100 971 6 746 6285United Kingdom 44 0442 84 6855United States 800-328-2910Service Phone NumbersCountry Phone Number
Blank Page
September 30, 2004 7F3319 4-14Adding a ModalityAfter the Imager has been placed into service, you can later configure the Imager to print images from additional modalities. The Imager is capable of receiving images from twelve DICOM-compatible modalities concurrently. Adding a modality involves adjusting some of the image quality settings in the Imager to match the new modality. The following procedure explains how to add one new modality.NOTE: You must have the Service Passcode to perform this procedure.Preparing to Add a Modality• Before you begin, make sure that the new modality has been set up to print to the Imager. The Imager must be available as a print destination in the modality print command.• You will need the following information about the modality:– The modality manufacturer– The modality type (CT, MR, etc.)– The modality model designation– The type and size of film to be used– Is the modality GSDF-compliant?– If GSDF-compliant, does the modality use PLUTs for all images it sends or only for some images?• You should also decide on a screen name for the modality. This name will be used only on the Imager Local Panel to identify the modality
4-2 7F3319 September 30, 2004Adding a ModalityModality-Related ParametersThe Imager must be configured to print from each connected modality. In the Imager a set of modality-specific parameters must be created for each modality that will print to the Imager. For many modalities, the required parameters can be taken from the "Modality Preferences Database" (MPDB). This internal database, within the Imager, contains tested parameter sets for many commonly used modalities.Modality configuration is accomplished in three ways:•First Print - When a modality prints to the Imager for the first time, the Imager automatically attempts to identify the type of modality from information included in the print job. If the Imager identifies the modality, it searches for a parameter set in the MPDB. If an appropriate parameter set is not found, the Imager assigns a universal set of parameters to the modality. If the parameter set does not produce acceptable prints, the installer can go on to the "Manufacturer/Model/Type" procedure.•Manufacturer/Model/Type - If the automatic search in the MPDB is not successful, the installer can enter the Manufacturer, Model and Type of the modality on the Local Panel. The Imager uses this information to search the MPDB again for a set of parameters. A universal parameter set is applied if an approprialte parameter set is not found. If the parameter set is not acceptable, the Installer must use the Manual Entry method.•Manual Entry - The installer can enter or adjust individual modality parameter values on several modality configuration screens.For each of the above methods, the user must print a clinical image and check image quality to determine if the parameter set is acceptable.The user can use a combination of manual entry and one of the other two methods. For example, the user may accept the "First Print" parameter set but adjust one or two of the parameters manually to suit local preferences.The parameter set selected using the above methods is placed in a "Connection Database" in the Imager and used to print all images from the modality. The Connection Database contains a separate parameter set for each modality associated with the Imager.
Adding a ModalitySeptember 30, 2004 7F3319 4-3Configuration ProcedureThe modality setup procedure is performed on the Imager Local Panel. 1. Be sure that the proper film size and type required for the modality is loaded in the Imager.2. Start from the Home screen.3. Press Menu.4. Touch Setup Imager.
4-4 7F3319 September 30, 2004Adding a Modality5. Select Modality (SCU) config. 6. Enter the Service User ID (99) and the Service Passcode on the keypads that appear.NOTE: If the new modality has previously printed to the Imager but has not been configured, it will appear on the above list but without a footprint symbol.7. Send an Image from the new modality to the Imager.• If this is the first time the new modality has printed to the Imager, continue with step 8.• If the modality has previously printed to the Imager, go to step 10 on page 4-6.Previously Configured Modalities
Adding a ModalitySeptember 30, 2004 7F3319 4-58. Wait for the following message screen to appear - about 1 minute. (When a modality prints to the Imager for the first time, this message will appear.)NOTE: If this message does not appear, the modality may not be properly set up to print to the Imager. Check the modality setup and re-send the image.9. Touch OK.The modality that sent the image should now appear at the bottom of the list of modalities.IP Address of the modality that has printed to the Imager New Modality - that just printed
4-6 7F3319 September 30, 2004Adding a Modality10. Wait for the Imager to print the image sent from the modality.• The imager will attempt to find an appropriate set of parameters for the modality in its internal database of modality parameters.• If no parameter set is found for the modality, the Imager uses a universal set of parameters to print the test image.11. Examine the quality of the print. Determine if it is acceptable.12. On the Select Modality screen (page 4-4), select the modality that printed the image.13. Is the quality of the print acceptable?• If acceptable, touch No (do not use the modality installation assistant). Go to “Changing the Modality ID” on page 4-10.• If not acceptable, touch Yes (use the modality installation assistant). You will now see a series of screens that will allow you to enter the Manufacturer, Type and Model of the modality. The Imager will use this information for a second search of its parameter database.
Adding a ModalitySeptember 30, 2004 7F3319 4-714. Touch Yes.15. Select the name of the modality manufacturer.
4-8 7F3319 September 30, 2004Adding a Modality16. Select the modality type.17. Select Model.• The Imager searches the parameter database: – If an appropriate set of parameters is found, these parameters will be applied to all images printed from this modality.– If no parameter set is found for the modality, a universal set of image quality parameters is assigned to the modality. You will probably have to modify some of these parameters to achieve satisfactory image quality.• The Modality defaults screen appears.
Adding a ModalitySeptember 30, 2004 7F3319 4-918. Send another clinical image from the modality to the Imager.19. Wait for the Imager to print.20. Examine the quality of the print.21. Is the quality of the test print acceptable?•Yes - Go to “Changing the Modality ID” on page 4-10.•No - You can change image quality by adjusting individual image quality parameters:a. Select Image quality on the Modality defaults screen.b. If the above information screen appears, Touch [X]. The Image Quality screen appears.
4-10 7F3319 September 30, 2004Adding a Modalityc. Go to Section 5 of this manual to adjust the parameters shown on the Image Quality screen.d. After completing the procedure in Section 5, continue with “Changing the Modality ID”.Changing the Modality ID The Modality ID sent down from the modality is a combination of modality type and IP Address. If you wish, you can change this "name" to a more user- friendly name for use on the Local Panel Screens as follows: 1. With Modality ID highlighted, touch Select. A keypad appears on the Local Panel.2. Use the keypad to enter a new name for the modality.3. Touch OK to return to the Modality defaults screen.
Adding a ModalitySeptember 30, 2004 7F3319 4-11Setting the Advanced ParametersNOTE: The Imager automatically sets the Advanced default parameters for a modality when you begin the modality setup process. In most cases these settings are satisfactory. Do not change these parameters unless you are certain that your application of the modality requires different settings. 1. Return to the Modality defaults screen.2. Select Advanced. A list of "Advanced" parameters with their currently selected default values appears.
4-12 7F3319 September 30, 2004Adding a ModalitySelecting Film Size The film sizes accepted by the Imager are 14 by 17 in., 11 by 14 in., and 14 by 14 in. If the default size shown on the screen is not the desired size, change it.1. On the Advanced defaults screen, highlight Film Size.2. Use the Select button to choose the film size appropriate for this modality. Each time you touch Select, the film size will change.3. For most installations Override modality should be left at false.NOTE: If you select True for Override modality, the Film Size set in step 2 will take precedence over any film size requested by the modality.4. Touch the Back arrow to return to the Advanced defaults screen.
Adding a ModalitySeptember 30, 2004 7F3319 4-13Selecting Film Type The Film Type choices are DVB (DryView Blue) and DVC (DryView Clear). There is more than one type of Kodak DryView DVB film. The DVB choice applies to all DVB and DVB+ film types.If the default shown is not correct for this modality, change the value as follows1. On the Advanced defaults screen, highlight Film Type.2. Touch Select. The Edit DICOM attribute screen appears.3. Use the Select button to choose the type of film appropriate for this modality.4. For most installations Override modality should be left at false.NOTE: If you select True for Override modality, the Film Type set in step 3 will take precedence over any film type requested by the modality.5. Touch the Back arrow to return to the Advanced defaults screen.
4-14 7F3319 September 30, 2004Adding a ModalitySelecting the Type of Image ResizingIf the image sent down from the modality is too large for the size of film installed in the Imager, the Imager can resize the image to fit on the film by either of two methods:•Minify - To reduce the image to fit on the selected film size.•Crop - To remove the edges of the image to allow it to fit on the selected page size.For more information on these two methods, refer to “Image Resizing” on page 2-45.1. On the Advanced defaults screen, highlight Image Resizing.2. Touch Select to display the Edit DICOM attribute screen.3. Use the Select button to choose the desired resizing option (Minify or Crop).
Adding a ModalitySeptember 30, 2004 7F3319 4-154. For most installations Override modality should be left at false.NOTE: If you select True for Override modality, the Image Resizing mode set in step 3 will take precedence over any type of sizing requested by the modality.5. Touch the Back arrow to return to the Advanced defaults screen.Selecting Print Priority The Priority for prints determines the order in which the Imager will process prints if a number of modalities are requesting prints at the same time. You can select one of three priority levels.• High - Prints from this modality will take precedence over prints from modalities with lower priority.• Low - Prints from modalities with higher priorities will take precedence.• Medium - Prints from this modality have "medium" priority.1. On the Advanced defaults screen, highlight Priority.2. Touch Select to display the Edit DICOM attribute screen.
4-16 7F3319 September 30, 2004Adding a Modality3. Use the Select button to choose the desired priority for printing.4. For most installations Override modality should be left at false.NOTE: If you select True for Override modality, the priority set in step 3 will take precedence over any priority requested by the modality.5. Touch the Back arrow to return to the Advanced defaults screen.
Adding a ModalitySeptember 30, 2004 7F3319 4-17Selecting N_Event Reporting "N_Events" are status changes at the Imager, such as changes from "ready" to "busy." The Imager can be configured to report these status changes to the modality as they changes occur. CAUTION:This feature can cause a serious malfunction in the modality if it is not designed or configured to accept N_Event messages. Leave the N_Event reporting attribute set to false unless you are certain the modality can accept N_Event messages.1. On the Advanced defaults screen, highlight N_Event reporting.2. Touch Select to display the Edit DICOM attribute screen.3. Use the Select button to choose true or false. Selecting true enables the Imager to send N_Event messages to the modality.4. For most installations Override modality should be left at false.NOTE: If you select true for Override modality, the "N_Event Reporting" value set in step 3 will take precedence over any request from the modality.5. Touch the Back arrow to return to the Advanced defaults screen.
4-18 7F3319 September 30, 2004Adding a ModalitySelecting Report Warnings "Warnings" are messages from the Imager indicating a non-fatal problem in the Imager. Like "N_Events," these can be sent to the modality if desired, but they should not be if they can cause problems at the modality.1. On the Advanced Defaults screen, highlight Report Warnings.2. Use the Select button to choose Yes or No.Selecting Use of a Density Patch on the FilmA "Density Patch" (also called "dPatch") is a small area of specified density on the edge of the film that can be used by the Imager software to monitor and control changes in density from print to print. The Density Patch is used only on 14 x17 in. film. If the modality requires a different size film, leave this parameter set to No.1. On the Advanced Defaults screen, highlight Density patch.2. Use the Select button to choose Yes or No.If you select Yes, the Imager will print a Density Patch on the edge of every print. If you select No, it will not.When Density Patch is selected, the Automatic Image Quality Control (AIQC) system in the Imager is enabled. This system monitors image quality automatically and makes adjustments to minimize sheet-to-sheet density variation.
Adding a ModalitySeptember 30, 2004 7F3319 4-19Selecting Color Negotiation The Imager prints only grayscale images. If a modality has color capability and a request to print a color image is sent to the Imager, the Imager software can print a grayscale version of the color image.1. Touch the Down arrow to proceed to the second Advanced defaults screen.2. Use the Select button to choose No.NOTE: If you select No, the Imager will not accept color prints from the modality. If you select Yes, it will print a gray scale version of the color print. 3. Touch the Back arrow to return to the Modality defaults screen.
4-20 7F3319 September 30, 2004Adding a ModalitySetting up the Text(Annotation) BoxThis parameter allows you to select items to be printed in a "text box" on the bottom of each sheet of film.1. Select Film Text to display the items you can select.2. Select Hospital name if you wish to include the name of your hospital in the annotation box. A check will display adjacent to the field.a.Select (Edit Hospital name) and touch OK.b.Use the keypad to enter the name.c.Touch OK.3. Select any or all of the other items on the screen. A check will display adjacent to each item you select.4. Touch the Back arrow to return to the Modality Defaults screen.
Adding a ModalitySeptember 30, 2004 7F3319 4-21Saving the Modality (SCU)Parameters1. Select Save Changes to save the parameter changes you have made.2. Touch OK.3. Touch the Back arrow twice to return to the Setup Imager screen.
4-22 7F3319 September 30, 2004Adding a ModalityBacking up the ConfigurationThe configuration parameters must be backed up (recorded) on a floppy diskette so they can be restored if the Imager software is updated.You will need a blank 3.5-inch floppy diskette, 1.44 mb, IBM format.1. Start from the Setup Imager screen.2. Select Backup Configuration.3. Touch Yes.
Adding a ModalitySeptember 30, 2004 7F3319 4-234. Touch OK.5. Choose an easy-to-remember file name for the backup file. For example,a:\09_15_04.bin or a:\backup1.bin. The prefix a:\ and suffix .bin are required.6. Write down the filename. 7. Enter the filename on the keypad and touch OK on the keypad.
4-24 7F3319 September 30, 2004Adding a Modality8. Touch Yes.9. Wait for the front door to open.
Adding a ModalitySeptember 30, 2004 7F3319 4-25The Imager first closes the film cartridge and then unlatches the door. This takes about 30 seconds.10. Open the computer access door.11. Insert a blank diskette into the floppy disk drive.The Imager records a backup file of the configuration parameters on the diskette.H200_0034DAAFront DoorComputerAccess Door
4-26 7F3319 September 30, 2004Adding a Modality12. Touch OK.13. Remove the floppy disk from the computer.14. On the disk label, write the filename exactly as you entered in step 7. Include the date of the backup.15. Store the floppy disk in a safe place. It may be required if the Imager is serviced.16. Close the computer access door and the Imager front door.17. Log out of the Service Passcode:a.Touch the Back arrow to return to the Main Menu.b.Touch System Functions.c.Touch Log off and then Touch OK.
Adding a ModalitySeptember 30, 2004 7F3319 4-2718. Press the Back arrow.The Home screen should appear. Configuration of the new modality is now complete.
Blank Page
September 30, 2004 7F3319 5-15Optimizing Image QualityImage Quality ParametersIf the quality of an image printed by the Imager is not acceptable, you will have to enter new values for the parameters shown on the "Image quality" screen. This section provides basic information that will help you select and enter values for these parameters that are appropriate to the type of modality that sent the image. The "Image quality" parameters include:•Image Density - A setting that determines the maximum density (Dmax) that will be used in printing.•Border density - The density of the border of the film.•TFT Set - A group of 15 Transfer Function Tables (TFTs) used in Kodak Imagers. Each TFT in the set is a grayscale curve that relates each digital input (pixel) value to a target value of perceived brightness and a corresponding target value of printed optical density. •Table number - A number (1- 15) which specifies a particular TFT (contrast curve) in the TFT Set selected for printing.The Advanced Parametersare "Polarity" and "SmoothingType."
5-2 7F3319 September 30, 2004Optimizing Image Quality•Advanced - Includes two parameters:–Polarity - In general, indicates whether an image is black on a white background or the reverse. In this case, specifies whether the Imager will print images with the same polarity as the images sent from the modality (Positive), or the reverse (Negative).–Smoothing Type - A value (1 - 15) that specifies a level of smoothness/sharpness in transition between density differences.Selecting the Image Quality Parameter ValuesUse Table 1 (on page 5-4) and Table 2(on page Page 5-8) to select the image quality parameters. The parameter selections are based on modality type. They also depend on whether the modality is GSDF-compliant. (GSDF stands for Grayscale Standard Display Function.)To select the parameters:• If the modality is not GSDF-compliant, go to “Non-GSDF Modalities” below.• If the modality is GSDF-compliant and does not use PLUTs or uses PLUTs for only some images, go to “GSDF-Compliant Modalities” on page 5-9.(PLUT stands for Presentation Look-Up Table.)• If the modality is GSDF-compliant and uses PLUTs for all images, it is not necessary to change the image quality values in the Imager. Continue with “Setting the Advanced Parameters” on page 4-11.Non-GSDF Modalities Use this procedure to select parameters for modalities that are not GSDF- Compliant.Write down the parameter values you select.1. Refer to Table 1 and find the Modality Type for which the Imager is being configured.2. Choose the TFT Set recommended in the table for this type of modality. If more than one TFT Set is listed, read the Notes in the table for guidance in selecting the appropriate set.3. Choose the Table No. (contrast setting) recommended for the chosen TFT Set. If a number is in boldface type, choose this number first. (You may have to try more than one Table Number.)
Optimizing Image QualitySeptember 30, 2004 7F3319 5-34. Choose the Image Density associated with the Table No. you chose. If there is a range of density values:• Choose the density value indicated in bold if there is one.• If there is no bold value, choose the middle value. For example, if the range is 2.7 to 3.1, choose 2.9.• If there are only 2 density values, choose either one.5. Choose the Smoothing Type from Table 1.6. For Border Density on the film, choose a low density for a clear border and a high density for a black border. Typically this density is matched to the Image Density. (This parameter is not included in Table 1.) 7. For Polarity of the film, choose either Positive or Negative. Positive is used for most applications. Negative is used by Nuclear Medicine modalities. (This parameter is not included in Table 1.)8. Continue with “Entering the Image Quality Parameters” on page 5-10.
5-4 7F3319 September 30, 2004Optimizing Image QualityTable 1. Selection of Parameters by Modality Type Modality Type TFT Set Table No. (Contrast Setting)*Image Density (Dmax)*Smooth-ing Type NoteKodak and other CR (Computed Radiography) and DR (Digital Radiography) Systems. Also Workstations and imaging devices that output data to a linear-in- density contrast curve.WRKSTN2A.w87 12343.13.02.92.85Select Table number (contrast) and Dmax in the pairs shown. Do not use with Fuji CR.(See Fuji CR below.)Fuji CR FCR302C4.w87 1011121314152.62.72.82.93.03.15Table number (contrast) and Dmax must be chosen in the pairs shown. The contrast curves are approximately linear in density for most of the pixel value range, but become relatively flat at high (bright) pixel values. Designed for use with Fuji CR only.CT (Computed Tomography) or MRI (Magnetic Resonance)VER693C0.w87 5, 7, 8 3.0, 3.1 15 Table 7 provides good grayscale range in all CT and MRI studies. Table 5 has less mid-tone contrast. Table 8 has more mid-tone contrast.
Optimizing Image QualitySeptember 30, 2004 7F3319 5-5DSA (Digital Subtraction Radiography), including C-Arm and Digital FluoroVER713C0.w87(Alternative 1)6, 7, 9 2.9 - 3.1 15 VER713C0 provides brighter image background than VER693C0. Lower Table numbers have less mid-tone contrast. Higher have more.VER693C0.w87(Alternative 2)6, 7, 9 2.9 - 3.1 15 VER693C0 provides darker image background than VER713C0. Lower Table numbers have less mid-tone contrast. Higher have more.Phillips Medical Systems (PMS) - EasyVision and other PMS modalities.PMSV3K.w87 9 3.0, 3.1 15 Check with the PMS service engineer. On some PMS modalities, image quality calibration must be run from the PMS control console.Table 1. Selection of Parameters by Modality Type Modality Type TFT Set Table No. (Contrast Setting)*Image Density (Dmax)*Smooth-ing Type Note
5-6 7F3319 September 30, 2004Optimizing Image QualityNuclear Medicine VER713C0.w87(Alternative 1)5 - 7 - 10 2.2, 2.3 12 Table 7 is popular. Table 5 has less mid-tone contrast and shows more isotope takeup. Table 10 has more mid-tone contrast and reduces takeup visibility on film. PMSV3K.w87(Alternative 2)10 - 14 2.2, 2.3 12 Start with Table 10. Higher tables have increased brightness and reduce isotope takeup visibility on film. Lower tables show more takeup.Siemens Host Control or WorkstationWRKSTN2A.w87 42.815Typically the density is set to 2.8 by the Siemens host control software. Table 4 must be chosen for linear grayscale translation.Table 1. Selection of Parameters by Modality Type Modality Type TFT Set Table No. (Contrast Setting)*Image Density (Dmax)*Smooth-ing Type Note
Optimizing Image QualitySeptember 30, 2004 7F3319 5-7Ultrasound VER693C0.w87(Alternative 1)5 - 8 - 12 2.4 - 2.8 15 Table number choices vary with manufacturer and radiologist. Lower table numbers have less mid-tone contrast. Higher numbers have more.PMSV3K.w87(Alternative 2)7 - 10 - 13 2.4 - 2.8 15 Table number choices vary with manufacturer and radiologist. Higher table numbers have increased brightness.Notes: * The number in bold should be the first choice when you are selecting parameter values.Table 1. Selection of Parameters by Modality Type Modality Type TFT Set Table No. (Contrast Setting)*Image Density (Dmax)*Smooth-ing Type Note
5-8 7F3319 September 30, 2004Optimizing Image QualityNOTE: Some DICOM GSDF-modalities may direct the use of DICOM Presentation Look Up Tables (PLUTs) for some or all images. If the PLUT capability in the 8150 Imager is enabled, a PLUT sent from the modality overrides the GSDF0 TFT set (used for GSDF modalities) and associated parameter settings. The DICOM PLUT capability in the Imager is normally enabled but can be disabled by your Service Provider.Table 2. GSDF0 Dmax Setting versusTable Number (Contrast Setting)Density (Dmax) Table Number (Contrast)1.7 11.8 21.9 32.0 42.1 52.2 62.3 72.4 82.5 92.6 102.7 112.8 122.9 133.0 143.1 15Density and Table Number must be chosen in the pairs shown.
Optimizing Image QualitySeptember 30, 2004 7F3319 5-9GSDF-Compliant Modalities Use this procedure to select image quality parameters for GSDF-Compliant modalities that do not use PLUTs or use PLUTs for only some images.Write down the parameter values you select.a. Choose TFT Set GSDF0.w87 (used for all GSDF modalities).b. Refer to Table 1 (on page 5-4) and find the Modality Type for which the Imager is being configured.c. Choose Image Density. Choose the recommended density value in the Image Density column. If there is more than one density value:• Choose the bold value if there is one.• If there is a range of values (but no bold value), choose the middle value.• If there are only 2 values, choose either value.d. Refer to Table 2 (on page 5-8). Choose the Table Number that corresponds to the Image Density value you selected.e. Choose the Smoothing Type for the modality type from Table 1.f. For Border Density on the film, choose a low density for a clear border and a high density for a black border. Typically this density is matched to the Image Density. (This parameter is not included in Table 1.) g. For Polarity of the film, choose either Positive or Negative. Positive is used for most applications. Negative is used by Nuclear Medicine modalities. (This parameter is not included in Table 1.)h. Continue with “Entering the Image Quality Parameters” on page 5-10.
5-10 7F3319 September 30, 2004Optimizing Image QualityEntering the Image Quality Parameters1. After choosing the parameter values for the modality, enter them from the Image quality screen. • Each choice on this screen calls up an entry screen for one of the parameters.• On some parameter entry screens an Override Modality option appears. The choices are True or False. For most installations you should select False.If you select False, the parameter value you enter will be used only if the modality does not send this parameter with a print job.NOTE: Select Advanced to enter Smoothing Type and Polarity.2. Touch the Back arrow (2 or 3 times) to return to the Modality defaults screen.
Optimizing Image QualitySeptember 30, 2004 7F3319 5-113. Select Save changes to save the changes you have made, and touch OK.4. Send another image from the modality and check print quality.NOTE: For DICOM GSDF-compliant modalities, the printed images should approximately match images on DICOM GSDF-compliant displays.5. Is the quality of the print acceptable?• Yes: Continue with“Setting the Advanced Parameters” on page 4-11. • No: Select Image Quality.6. If an "Image Quality Help" screen appears, touch X.7. Refer again to Table 1 (Table 2 for GSDF-compliant modalities) and choose the Table No. (for the same modality type) that is just below or
5-12 7F3319 September 30, 2004Optimizing Image Qualityabove the one you previously entered.8. Enter and save the new Table number (steps 1 - 3). 9. Send another image from the modality and check print quality again.NOTE: You may have to try other Table numbers (and Densities) to achieve high quality prints.10. When print quality is acceptable, return to “Changing the Modality ID” on page 4-10.11. If you are unable to achieve satisfactory quality, call service for help. Refer to “Calling for Support” on page 3-17.
September 30, 2004 7F3319 6-16 SpecificationsDimensionsElectricalHeight: 117 cm (46 in.) - Top cover closed158 cm (62.3 in.) - Top cover openWidth: 63.5 cm (25 in.)Depth: 66 cm (26 in.) - Front door closed124.5 cm (49 in.) - Front door openWeight: 204 kg (450 lb)Voltage: 100 V ±10%, 50/60 Hz ±3 Hz120 V ±10%, 50/60 Hz ±3 Hz230 V ±10%, 50/60 Hz ±3 HzCurrent Draw: 100 V: 12 Amps max.120 V: 10 Amps max.230 V: 5.3 Amps max.Power Consumption: 1200 W (maximum)
6-2 7F3319 September 30, 2004SpecificationsLaser SpecificationsOperating EnvironmentStorage EnvironmentEnvironmental EffectsWavelength: 805 - 815 nmPower: 50 mW Type DiodeDiode Radiation Class: 3BImager Radiation Class Class 1 product Temperature: 15° to 35° C (59° to 95° F)Humidity: 15% to 85% RH, non condensingMagnetic Field: < 50 GaussAltitude 3048 - 12,192 m (100 - 40, 000 feet)Temperature: -35° C to 60° C (-31° F to 140° F)Humidity: 10% to 90% RH, non condensingAltitude Up to 3048 m (10,000 feet)Heat Dissipation: 3000 BTU/hour (average)Acoustical Noise: Less than 55 dB at one meter (70 dB momentary)Less than 80 dB, non-repetitive tasks such as door open/close
SpecificationsSeptember 30, 2004 7F3319 6-3Film SizesThe 8150 Laser Imager processes the following film sizes:•28 x 35 cm DryView Film (11 x 14 in. landscape)•35 x 35 cm DryView Film (14 x 14 in.)•35 x 43 cm DryView Film (14 x 17 in.)Film TypesThe 8150 Laser Imager processes the following film types:•Kodak DryView DVB Laser Imaging Film•Kodak DryView DVC Laser Imaging Film•Kodak DryView DVB+ Laser Imaging Film•Kodak DryView DVB+ Premium Laser Imaging FilmNOTE: Not all of these film types are available in every country.Film ThroughputPrints 70 films per hour.Agency ComplianceSee the Kodak DryView 8150 Laser Imager Safety Manual, document number 7F3779.
Blank Page
September 30, 2004 7F3319 7-17Film Technical InformationGeneral DescriptionThis section describes the characteristics of Kodak DryView Laser Imaging Film, not the operation of the Kodak DryView 8150 Laser Imager. DryView Laser Imaging Film is a high-resolution, infrared-sensitive, photothermographic film designed specifically for the family of Kodak DryView Laser Imagers. DryView Laser Imaging Film is packaged in daylight load packages, available in blue or clear, 7-mil polyester base.The 8150 Laser Imager accepts three film sizes:• (28 x 35 cm) 11 x 14 in. • (35 x 35 cm) 14 x 14 in. • (35 x 43 cm) 14 x 17 in. Spectral Sensitivity DryView Laser Imaging Film is infrared sensitive and has been sensitized to the infrared laser diode of DryView Laser Imagers. When handled according to instructions on the daylight-load film package, safelights are not needed. If you remove undeveloped film from the daylight load package, you will need a darkroom setting and a green safelight.
7-2 7F3319 September 30, 2004Film Technical InformationRelative Log Exposure (Example)Image Quality DryView Laser Imaging Film delivers diagnostic-quality, continuous-tone images along with sharp alphanumerics and optimum contrast. This high-quality, silver-based film provides radiologists with the same diagnostic information they are accustomed to viewing - including the spatial resolution, contrast and grey levels. Because it is a totally dry imaging process, there is no image quality variability due to “wet” chemistry.Automatic Image Quality Control DryView Laser Imaging Film is system-matched for the Kodak patented Automatic Image Quality Control (AIQC) technology. This fully automated system, which is a standard feature of DryView Laser Imagers, is designed to ensure that image quality parameters meet preset user preferences, film-to-film, lot-to-lot.Environmental Impact Tests show that DryView Laser Imaging Film is not considered hazardous to the environment. As a result, you can develop, recycle, and dispose of film with less impact on the environment than if you were using wet-developed silver halide films. Sensitometric CharacteristicsRELATIVE LOG EXPOSURE0 0.5 1 1.5 2 2.5 300.511.522.533.5DENSITYH188_1072AC
Film Technical InformationSeptember 30, 2004 7F3319 7-3Recycling Film According to the Environmental Protection Agency (EPA) standards, DryView Laser Imaging Film is not considered hazardous and requires no special disposal procedures. However, the film does contain silver and polyester that may be recovered by using one of several recycling processes.Call your local Kodak sales representative or go to the Kodak web sitewww.kodak.com/go/KESRefer to Publication J700 and see “End of Life Management' section.Storing and Handling Undeveloped FilmTo achieve consistent results up to the expiration date indicated on the film package, DryView Laser Imaging Film must be stored in a cool, dry place (41° F/5° C to 77° F/25° C) and protected from radiation and chemistry fumes. The film can withstand short-term temperature spikes (up to 95° F/35° C) for several hours during transit without any significant effect on film quality or performance. Transit temperatures above 95° F/35° C will gradually diminish shelf life. If the AIQC encounters film that has been damaged by improper handling, the AIQC will automatically alert system operators.DryView Laser Imaging Film - US Environmental Regulations ComparisonWet Silver Halide DryViewDeveloper Fixer Wash Film FilmProduct RegulationsOSHA MSDS Required Required Not required Not required ProvidedDOT Hazardous Hazardous No limits No limits No limitsUse permits Local Local None None NoneDisposal* RegulationsEPA Hazardous Hazardous No No NoDOT Hazardous Hazardous No No NoNote: There is no SUPERFUND liability with DryView Laser Imaging Film.* State and local laws vary. Consult appropriate regulations or authorities prior to disposal.
7-4 7F3319 September 30, 2004Film Technical InformationHandling Developed Film Handling DryView Laser Imaging Film requires reasonable care.Prolonged exposure to intense light or excessive heat (130° F/54.4° C) for more than 3 hours may cause some gradual darkening of images. Leaving films in vehicles in hot climates for extended periods of time is not recommended.Spills, humidity and other forms of water typically have no significant effect on image quality or film integrity. If necessary, film can be cleaned with a clean, damp cloth.For best results, store film in sleeves when not being reviewed. DryView Laser Imaging Film can be left on a light box for more than 24 hours. In extreme cases in which light boxes are exceptionally hot (120° F/49° C), Kodak recommends removing them prior to 8 hours of continuous exposure.Take care when using spotlight viewing for more than 30 seconds because temperatures near the light source may exceed 180° F/82.2° C. Use in slide projectors is not recommended due to the high temperatures generally found in these devices.With DryView technology, a small amount of final development occurs when the film exits the Laser Imager and is initially exposed to ambient or view-box lighting. This is virtually undetectable and has no effect on image quality (i.e., typically 0.02 change in density). This small density increase is uniform and permanent upon full exposure of the film under normal handling conditions (i.e., room light or view box).Archiving Developed Film DryView Laser Imaging Film has been tested and can be archived for more than 100 years when stored at American National Standards Institute (ANSI) recommended storage conditions (77° F/25° C). Developed films may be stored at higher temperatures; however, that may reduce the number of years the film can be stored. For example, storing films at a constant elevated temperature of 90° F/32.2° C may reduce archive capability to 30 years.Dissipating Odor DryView technology eliminates virtually all unpleasant odors. While some low-level odors are produced during the development process, they pose no known adverse health risks. Processing odor levels are further reduced by a non-hazardous, recyclable filter in the Laser Imager. This filter traps most low-level odors and prevents them from dissipating into the work
Film Technical InformationSeptember 30, 2004 7F3319 7-5environment. To help maintain optimum performance, the filter requires periodic replacement. DryView Laser Imagers require no special venting.Dissipating Heat DryView Laser Imagers use controlled heat to develop DryView Laser Imaging Film. The heat has virtually no effect on the air temperature of the work area. The amount of heat dissipated into an area during a day is typically less than the heat generated by four 100-watt light bulbs.
Blank Page
September 30, 2004 7F3319 Glossary-1Glossary AIQC Automatic Image Quality Control.CR Computed Radiography, the process of creating digital radiographic images.CT Computed Tomography, the process of creating digital tomographic images.DICOM Digital Imaging and Communications in Medicine. A TCP/IP-based protocol for transmitting and receiving medical imaging and related data over a network.Dmax Maximum density. The density of an area on the film which has received maximum exposure.Dmin Minimum density. The density of an unexposed area on the film.Dpatch Density patch. A small patch of specified density on the trailing edge of each film that AIQC uses to monitor density change on film. DR Digital radiography, the process of creating digital radiographic images.DVB DryView Blue Laser Imaging Film.DVC DryView Clear Laser Imaging Film.GSDF Grayscale Standard Display FunctionKey operator The person(s) designated by the department manager to receive applications training and allowed access to password-protected areas to make system changes.Modality Medical equipment that actually generates medical images (for example, an MRI).MR Magnetic Resonance. N/A Not available or not applicable.K number The K number (Kodak number) is located on the Local Panel System Information Screen.Platen The metal surface on which the film rests as it is exposed.Shutdown The process of exiting current tasks and applications and turning the power off.SMPTE test pattern A Society of Motion Picture and Television Engineering monitor test pattern that is used for analyzing image-quality problems.
Glossary-2 7F3319 September 30, 2004Test type The type of test film that will be printed. Two film test types are available: a density test film (SMPTE pattern) and a calibration film.TFT Transfer Function Tables.Unprintable queue The queue of jobs that cannot be printed because of errors in the print jobs.
Eastman Kodak Company343 State StreetRochester, NY 14650Kodak and DryView are trademarks of Eastman Kodak Company.© Eastman Kodak Company, 2004

Navigation menu