ELAD srl FDM-DUO FDM-DUO User Manual ELAD FDM DUO

ELAD srl FDM-DUO ELAD FDM DUO

08_User Manual

www.eladit.com ELAD FDM-DUO Dual Mode SDR Transceiver USER MANUAL
ELAD FDM-DUO User Manual Rev 1.04 10/2014 © 2014 ELAD S.r.l. All rights reserved. No part of this document may be reproduced, published, used, disclosed or disseminated in any form or by any means, electronic, photocopying or otherwise, without prior written permission of ELAD S.r.l. 2 1 Index 2 FDM-DUO Overview .............................................................................................................................. 4 2.1 Notice ............................................................................................................................................ 4 2.2 Firmware versions ......................................................................................................................... 4 2.3 Introduction .................................................................................................................................. 4 2.3.1 Main Features ....................................................................................................................... 4 2.3.2 FDM-DUO Block Diagram ...................................................................................................... 5 2.4 Precautions ................................................................................................................................... 6 3 Front Panel Description ........................................................................................................................ 7 3.1 Rear Panel Description .................................................................................................................. 8 4 LCD ...................................................................................................................................................... 10 5 Quick Start ........................................................................................................................................... 11 5.1 Receive ........................................................................................................................................ 11 5.2 Transmit ...................................................................................................................................... 12 6 User Interface ..................................................................................................................................... 13 6.1 VFO Mode ................................................................................................................................... 13 6.1.1 Receive ................................................................................................................................ 13 6.1.2 Antenna Tuning Mode ........................................................................................................ 16 6.1.3 Transmit .............................................................................................................................. 17 6.2 MEM Mode ................................................................................................................................. 19 6.2.1 Receive ................................................................................................................................ 19 6.3 Knobs functions ........................................................................................................................... 21 6.4 Keys functions ............................................................................................................................. 22 6.5 Microphone Keys functions ........................................................................................................ 22 6.6 Settings Menu List ....................................................................................................................... 23 6.6.1 Frequency offset menu ....................................................................................................... 25 7 CAT Remote Control ........................................................................................................................... 26 7.1 Introduction ................................................................................................................................ 26 7.2 Computer control commands ..................................................................................................... 26 7.3 FDM-DUO CAT commands list .................................................................................................... 27 7.3.1 Active commands table ....................................................................................................... 27 7.3.2 Dummy commands table .................................................................................................... 30 8 Software & Driver Installation ............................................................................................................ 37 8.1 Software installation in Windows 8 Windows 7 and Windows XP ............................................. 37
ELAD FDM-DUO User Manual Rev 1.04 10/2014 © 2014 ELAD S.r.l. All rights reserved. No part of this document may be reproduced, published, used, disclosed or disseminated in any form or by any means, electronic, photocopying or otherwise, without prior written permission of ELAD S.r.l. 3 8.1.1 First-time install in Windows 8 and Windows 7 ................................................................. 37 8.1.2 First-time install in Windows XP ......................................................................................... 42 8.1.3 Update an existing software version .................................................................................. 46 8.2 FDM-DUO USB driver .................................................................................................................. 47 8.2.1 FDM-DUO USB driver installation in Windows 8 and Windows 7 ...................................... 47 8.2.2 FDM-S2 USB driver installation in Windows XP .................................................................. 50 8.2.3 FDM-DUO USB sound card .................................................................................................. 61 8.2.4 FDM-DUO USB CAT Serial port ............................................................................................ 62 9 Firmware update ................................................................................................................................. 63 9.1 User interface firmware update ................................................................................................. 63 9.2 RX demodulator and TX modulator firmware update ............................................................... 65 9.2.1 RX demodulator firmware update ...................................................................................... 66 9.2.2 TX modulator firmware update .......................................................................................... 67 9.3 USB interface firmware update .................................................................................................. 68 9.4 FPGA DDC update ....................................................................................................................... 68 Declaration of Conformity (EC) ................................................................................................................... 69
ELAD FDM-DUO User Manual Rev 1.04 10/2014 © 2014 ELAD S.r.l. All rights reserved. No part of this document may be reproduced, published, used, disclosed or disseminated in any form or by any means, electronic, photocopying or otherwise, without prior written permission of ELAD S.r.l. 4 2 FDM-DUO Overview 2.1 Notice Amateur radio regulations vary from country to country. Confirm your local amateur radio regulations and requirements before operating the ELAD FDM-DUO 2.2 Firmware versions The features described in this manual refers the following firmware versions RX Demodulator TX Modulator User Interface USB Interface FPGA Ver: 1.04 Date: 09/18/2014 Ver: 1.03 Date: 09/18/2014 Ver: 3.03 Date: 09/18/2014 Ver: 4.08 Date: 09/18/2014 Ver: 2.00 Date: 07/30/2014 2.3 Introduction Thank you for choosing the FDM-DUO. It is an innovative dual mode SDR transceiver covering the frequency range from 9kHz to 52MHz. The FDM-DUO can be used like a standard transceiver in stand-alone mode or connect to a PC to exploit the full potential of the ELAD FDM-SW2 software. 2.3.1 Main Features  Frequency range: RX 9kHz to 52MHz direct sampling receiver  TX 160m to 6m  Selectable power output 5W on Ham Bands or 0dBm RF Out connector  Double antenna connectors (RTX or separate RX/TX)  Operating Modes: CW LSB USB AM  ADC Linear LTC2165,16bit @122.88MHz  DDC FPGA Spartan 6 XC6SLX25 + Serial Flash for stand-alone mode  Stand-alone RX demodulator with STM32F4 ARM floating point μController  LPC1766 Cortex M3 for LCD & Keyboard control  TX modulator with STM32F4 floating point μP + AD9957 DDS @368.64 MHz  Clocking source Si5338 driven by 10MHz TCXO or External reference input  TX modulator from I2S source: MIC using Cirrus CS5346 or USB integrated Codec (CM6510B codec with customized firmware)  CAT USB interface with FTDI controller
ELAD FDM-DUO User Manual Rev 1.04 10/2014 © 2014 ELAD S.r.l. All rights reserved. No part of this document may be reproduced, published, used, disclosed or disseminated in any form or by any means, electronic, photocopying or otherwise, without prior written permission of ELAD S.r.l. 5 2.3.2 FDM-DUO Block Diagram
ELAD FDM-DUO User Manual Rev 1.04 10/2014 © 2014 ELAD S.r.l. All rights reserved. No part of this document may be reproduced, published, used, disclosed or disseminated in any form or by any means, electronic, photocopying or otherwise, without prior written permission of ELAD S.r.l. 6 2.4 Precautions  Connect the transceiver only to a power source described in this manual.  Take care when plugging in cables, avoid applying sideways pressure that might damage the connectors  Avoid operating in wet conditions.  For better performance and safety, connect the transceiver to goof earth ground using a short, heavy, braided cable.  Ground all outdoor antennas for this receiver using approved methods. Grounding helps protect against voltage surges caused by lightning. It also reduces the chance of build-up of static charge.
ELAD FDM-DUO User Manual Rev 1.04 10/2014 © 2014 ELAD S.r.l. All rights reserved. No part of this document may be reproduced, published, used, disclosed or disseminated in any form or by any means, electronic, photocopying or otherwise, without prior written permission of ELAD S.r.l. 7 3 Front Panel Description 1 - LCD Display See LCD. 2 - E1 Knob Audio volume , AGC, noise reduction, noise blanker control. Knobs functions 3 - Main Knob Main VFO and MEM control. See Knobs functions 4 - Speaker/Headphones Audio Output The main FDM-DUO audio output. 5 - Auxiliary Output Audio /IQ data output. 6 - E2 Knob Filter and pitch control. See Knobs functions 7 - MODE and MENU buttons Change operating mode and enter the FDM-DUO setup menu. See Keys functions 8 - VFO and MEM buttons Basic VFO Memory operations. See Keys functions
ELAD FDM-DUO User Manual Rev 1.04 10/2014 © 2014 ELAD S.r.l. All rights reserved. No part of this document may be reproduced, published, used, disclosed or disseminated in any form or by any means, electronic, photocopying or otherwise, without prior written permission of ELAD S.r.l. 8 3.1 Rear Panel Description 1 - USB Receiver Data Connector USB 2.0 port to connect with the PC. Please use the supplied cable. 2 - Frequency Reference Input SMA 50 Ohm 10MHz, 0 dBm frequency reference input. 3 - RF Output Connector SMA 50 Ohm 0 dBm TX output. 4 - RTX/TX Antenna Connector M-type RTX/TX 50 Ohm antenna connector. 5 - RX Antenna Connector M-type RX 50 Ohm antenna connector. 6 - PTT Output Connector PTT Output to connect a switch-box or an amplifier 7 - USB Audio Connector USB soundcard useful for digital modes 8 - CAT USB Serial Port USB serial port for CAT communication 9 - Power Switch Turn On/Off the FDM-DUO 10 - Power supply 13.8V, 2.5A DC power supply connector
ELAD FDM-DUO User Manual Rev 1.04 10/2014 © 2014 ELAD S.r.l. All rights reserved. No part of this document may be reproduced, published, used, disclosed or disseminated in any form or by any means, electronic, photocopying or otherwise, without prior written permission of ELAD S.r.l. 9 11 - Expansion Port DB9 connector for external hardware (eg pre-selector filters board). This is NOT a serial port. 12 - MIC/PTT input Compatible with the supplied microphone 13 – Key/Paddle input 3.5mm stereo jack connector. Can be used with any key or paddle If a paddle is connected, the CW LEFT and TIP can be configured as dot or dash in the CW LEFT and CW TIP settings menu. 14 – Ground Connector For better performance and safety, connect to an earth ground using a short, heavy cable.
ELAD FDM-DUO User Manual Rev 1.04 10/2014 © 2014 ELAD S.r.l. All rights reserved. No part of this document may be reproduced, published, used, disclosed or disseminated in any form or by any means, electronic, photocopying or otherwise, without prior written permission of ELAD S.r.l. 10 4 LCD 1. LP: Low pass input filter active. ATT: input attenuation active. 2. ANT 1 2: display the number of antennas. 3. IN MIC USB: display the input selected for transmission in SSB and AM modes. 4. Bar meter: in receiver mode displays the signal strength in S-units, in transmission mode displays the forward power transmitted. 5. Measurements unit for the main display. The “S” of SWR is also used to indicate the “QuickStep” function. 6. PK: blinks if the case of internal ADC overload. 7. Secondary display: in receiver mode displays the signal strength, in transmission mode displays the forward power transmitted. 8. Measurement unit for the secondary display. 9. LOC: on when the Main Knob is locked. 10. CAT: on when a CAT command is received, SERV: Service mode enabled. 11. Operating mode. 12. Input selection for CW mode. 13. External frequency reference present. 14. E2 Selected function. PITCH: CW pitch frequency, :Demodulation filter bandwidth. 15. Main display. 16. E1 Selected function. VOL: main volume, SQL: squelch, MIC: microphone gain, AGC: automatic gain control settings, NR: noise reduction, NB: noise blanker. 17. Display the selected VFO. 18. SET: settings menu mode, MEM: memory mode, VFO: VFO mode 19. In memory mode, displays the selected memory index, in settings mode display the menu number 20. RX: receive. TX: Transmit.
ELAD FDM-DUO User Manual Rev 1.04 10/2014 © 2014 ELAD S.r.l. All rights reserved. No part of this document may be reproduced, published, used, disclosed or disseminated in any form or by any means, electronic, photocopying or otherwise, without prior written permission of ELAD S.r.l. 11 5 Quick Start These instructions are intended only for a quick guide, detailed instructions are given later in this manual 5.1 Receive  Turn on the FDM-DUO using the rear panel switch. The transceiver start in VFO mode with the VFO-A selected.  Turn the E1 knob until you hear a suitable level of noise  Use the Main knob to tune a frequency  Press to select the desired communication mode  Use the E2 to set the demodulation filter
ELAD FDM-DUO User Manual Rev 1.04 10/2014 © 2014 ELAD S.r.l. All rights reserved. No part of this document may be reproduced, published, used, disclosed or disseminated in any form or by any means, electronic, photocopying or otherwise, without prior written permission of ELAD S.r.l. 12 5.2 Transmit  Use the Main Knob to tune in a desired station or select an unused frequency  Press and hold the key until enter in the Antenna Tuning Mode, the display change its back color  Tune the antenna...  Press and hold the key until return in the VFO mode  Press microphone PTT and speak into the microphone, the display change its back color  During the transmission use E1 to adjust the reception volume and E2 to adjust the power output
ELAD FDM-DUO User Manual Rev 1.04 10/2014 © 2014 ELAD S.r.l. All rights reserved. No part of this document may be reproduced, published, used, disclosed or disseminated in any form or by any means, electronic, photocopying or otherwise, without prior written permission of ELAD S.r.l. 13 6 User Interface 6.1 VFO Mode 6.1.1 Receive The VFO mode is the default mode of FDM-DUO. Each VFO memorize the tuning frequency, mode and tuning step 6.1.1.1 Tuning In this mode, use the Main Knob to tune a frequency. A short pressure on the main knob enter the frequency step menu Use the main knob to modify the tuning step, then with a short pressure return in the VFO menu With a long pressure over the main knob, the Digit by Digit Frequency tuning mode is activated In this mode use the main knob to modify the selected digit and E1 or E2 to change witch digit you want to modify. Apply a short pressure on main knob to return in the standard tuning mode
ELAD FDM-DUO User Manual Rev 1.04 10/2014 © 2014 ELAD S.r.l. All rights reserved. No part of this document may be reproduced, published, used, disclosed or disseminated in any form or by any means, electronic, photocopying or otherwise, without prior written permission of ELAD S.r.l. 14 6.1.1.2 E1 Receiver Settings Apply a short pressure on the E1 knob to change the E1 selected parameter, the selected parameter icon is turned on in the LCD. Turn until one click the E1 knob to display the parameter value, then turn again E1 to modify the parameter value. AGC: if the AGC is turned OFF (manual gain mode), the AGC icon blinks NR and NB: if the Noise Reducer or the Noise Blanker is turned on the relative NR or NB icon blinks. 6.1.1.3 E2 Receiver Settings Apply a short pressure on the E2 knob to change the E2 selected parameter, turn until one click the E1 knob to display the parameter value, then turn again E1 to modify the parameter value. 6.1.1.4 Switch VFO Use the button to switch VFO-A/B. 6.1.1.5 Store VFO to memory Use the key to store the current VFO settings into a memory Use E2 knob to select the destination memory and confirm with a short pressure on E2 6.1.1.6 “QuickMem” mode Keep pressed the key to enter the “QuickMem” mode. The memory channels 180 to 199 are reserved for the “QuickMem” selection. Keep pressed the key until the desired frequency appears on the LCD display, then release the key and the current VFO is set to the frequency and mode saved in the memory channel. You can use the “FDM-DUO Manager” feature in the ELAD FDM-SW2 software to customize the memory channels.
ELAD FDM-DUO User Manual Rev 1.04 10/2014 © 2014 ELAD S.r.l. All rights reserved. No part of this document may be reproduced, published, used, disclosed or disseminated in any form or by any means, electronic, photocopying or otherwise, without prior written permission of ELAD S.r.l. 15 6.1.1.7 VFO-A = VFO-B With long pressure on key you get VFO-A = VFO-B 6.1.1.8 Change Operating Mode With a short pressure on the button, you can change the receiver mode between the available modes: 6.1.1.9 “QuickStep” With a short pressure on the key, the “QuickStep” function is activated. This function quickly sets the frequency step preset selected in the “QuickStep” setting menu, press again the key to set the previous frequency step. USB CW AM LSB
ELAD FDM-DUO User Manual Rev 1.04 10/2014 © 2014 ELAD S.r.l. All rights reserved. No part of this document may be reproduced, published, used, disclosed or disseminated in any form or by any means, electronic, photocopying or otherwise, without prior written permission of ELAD S.r.l. 16 6.1.2 Antenna Tuning Mode In VFO or MEM mode, apply a long pressure on key to switch to the Antenna Tuning Mode In this mode a tone at the transmission frequency is generated. Use E2 to modify the transmission power. The antenna tuning mode have a default timeout of 10s, this value can be modified in the settings menu 50 “TUNE TIME”. However you can apply a long pressure on key to exit from the antenna tuning mode. Note: The timeout is not active if:  The transmission selected transmission output is set to 0dBm  The “SERVICE MODE” is active
ELAD FDM-DUO User Manual Rev 1.04 10/2014 © 2014 ELAD S.r.l. All rights reserved. No part of this document may be reproduced, published, used, disclosed or disseminated in any form or by any means, electronic, photocopying or otherwise, without prior written permission of ELAD S.r.l. 17 6.1.3 Transmit During the transmission some operations like tuning, VFO selection, mode selection are locked. With a short pressure on the E2 knob it is possible to change witch parameter is shown in the main display. 6.1.3.1 Transmission in CW mode 6.1.3.1.1 CW Message To begin to transmit the CW message selected in the “CW message menu”, keep pressed the microphone PTT and press the CW key. With a long pressure on if the function has been activated in the “F4 Function” menu, the selected CW message is transmitted. Push the PTT to terminate the CW message transmission 6.1.3.1.2 E1 transmitter settings Apply a short pressure on the E1 knob to the Reception Volume or the CW Words Per Minute parameter. Turn until one click the E1 knob to display the parameter value, then turn again E1 to modify the parameter value. 6.1.3.1.3 E2 transmitter settings Use E2 to change the transmission power
ELAD FDM-DUO User Manual Rev 1.04 10/2014 © 2014 ELAD S.r.l. All rights reserved. No part of this document may be reproduced, published, used, disclosed or disseminated in any form or by any means, electronic, photocopying or otherwise, without prior written permission of ELAD S.r.l. 18 6.1.3.2 Transmission in AM and SSB mode 6.1.3.2.1 E1 transmitter settings Apply a short pressure on the E1 knob to the Reception Volume or microphone gain parameter. Turn until one click the E2 knob to display the parameter value, then turn again E2 to modify the parameter value. 6.1.3.2.2 E2 transmitter settings Use E2 to change the transmission power
ELAD FDM-DUO User Manual Rev 1.04 10/2014 © 2014 ELAD S.r.l. All rights reserved. No part of this document may be reproduced, published, used, disclosed or disseminated in any form or by any means, electronic, photocopying or otherwise, without prior written permission of ELAD S.r.l. 19 6.2 MEM Mode 6.2.1 Receive To activate the memory mode, apply a long pressure on the button 6.2.1.1 Select and edit a memory Use the main knob to select a memory. Apply a long pressure on the main encoder to enter the edit memory menu. In this menu it is possible to modify the selected memory frequency in digit by digit mode. Use the button to select the VFO-A/B. This is useful if you want to set the memory settings to a specific VFO. 6.2.1.2 Delete a memory Apply a long pressure to the key to enter the delete menu. Use the E2 knob to set yes or no and make a short pressure on E2 to confirm. 6.2.1.3 Set memory to VFO Use the key to set the selected VFO to the selected memory frequency and mode. When this function is used, the FDM-DUO automatically switches to the VFO mode
ELAD FDM-DUO User Manual Rev 1.04 10/2014 © 2014 ELAD S.r.l. All rights reserved. No part of this document may be reproduced, published, used, disclosed or disseminated in any form or by any means, electronic, photocopying or otherwise, without prior written permission of ELAD S.r.l. 20 6.2.1.4 Change the memory display mode Apply a short pressure on the key to show the memory label in the LCD main display. Press shortly again to return to display the memory frequency. You can use the “FDM-DUO Manager” feature in the ELAD FDM-SW2 software to customize the memory channels.
ELAD FDM-DUO User Manual Rev 1.04 10/2014 © 2014 ELAD S.r.l. All rights reserved. No part of this document may be reproduced, published, used, disclosed or disseminated in any form or by any means, electronic, photocopying or otherwise, without prior written permission of ELAD S.r.l. 21 6.3 Knobs functions The following table describes the knob functions for each user interface menu Mode/Menu Action Main Knob E1 Knob E2 Knob VFO Value modified Change selected VFO frequency Enter E1 selection parameter Enter E2 selection parameter Short Pressure Enter STEP menu Change E1 selected parameter Change E2 selected parameter Long Pressure Switch to DIGIT by DIGIT tuning mode STEP Value modified Change tuning step value Short Pressure Exit from STEP Menu Long Pressure Switch to DIGIT by DIGIT tuning mode MEM Value modified Select next/previous memory Modify E1 selected parameter value Modify E2 selected parameter value Short Pressure Change E1 selected parameter Change E2 selected parameter Long Pressure Enter the menu to change the selected memory frequency E1 Selection: VOL - AGC- NR - NB Value modified Back to VFO or MEM menu Modify E1 selected parameter value Modify E2 selected parameter value Short Pressure Back to VFO or MEM menu Change E1 selected parameter Change E2 selected parameter Long Press Switch to digit by digit tuning mode E2 Selection: FILTER - PITCH Value modified Back to VFO or MEM menu Modify E1 selected parameter value Modify E2 selected parameter value Short Pressure Back to VFO or MEM menu Change E1 selected parameter Change E2 selected parameter Long Pressure Switch to digit by digit tuning mode VFO > MEM Value modified Change the destination memory Change the destination memory Short Press Save VFO in the selected memory Long Pressure Delete MEM Value modified Change Yes/No Short Pressure Confirm Yes/No Long Pressure SETUP Value modified Parameter large step variation (1) Short Press Long Pressure DIGIT by DIGIT Tuning Value modified Modify the current digit value Change digit selection Change digit selection Short Pressure Switch to standard tuning mode Switch to standard tuning mode Switch to standard tuning mode Long Pressure (2) (2)
ELAD FDM-DUO User Manual Rev 1.04 10/2014 © 2014 ELAD S.r.l. All rights reserved. No part of this document may be reproduced, published, used, disclosed or disseminated in any form or by any means, electronic, photocopying or otherwise, without prior written permission of ELAD S.r.l. 22 (1) Available only for certain menu (2) Press simultaneously E1 and E2 to lock/unlock all the keys and knobs 6.4 Keys functions The following table describes the keys functions. Mode Pressure VFO Short Switch VFO Enter VFO to MEM menu - Change operating mode Enable/disable Quickstep function Enter settings menu VFO Long Switch to MEM mode Enter “QuickMem” menu VFO A = B Enter/Exit antenna tuning mode F4 Selected Function Lock/Unlock the main knob MEM Short Switch VFO - Selected memory to VFO Change selected memory operating mode Change memory display frequency/label Enter settings menu MEM Long Switch to VFO mode Enter delete memory menu - Enter/Exit antenna tuning mode F4 Selected Function Lock/Unlock the main knob 6.5 Microphone Keys functions The following table describes the microphone keys functions. Mode Pressure UP UP Keep pressed DOWN DOWN Keep pressed VFO Short Tune up frequency of one step Tune down frequency of one step VFO Keep pressed After HOLDTIME tune up the frequency according with the acceleration After HOLDTIME tune down the frequency according with the acceleration MEM Short Selected memory to VFO Selected memory to VFO MEM Keep pressed Selected memory to VFO and after HOLDTIME tune up the frequency according with the acceleration Selected memory to VFO and after HOLDTIME tune down the frequency according with the acceleration
ELAD FDM-DUO User Manual Rev 1.04 10/2014 © 2014 ELAD S.r.l. All rights reserved. No part of this document may be reproduced, published, used, disclosed or disseminated in any form or by any means, electronic, photocopying or otherwise, without prior written permission of ELAD S.r.l. 23 6.6 Settings Menu List The following table describes the FDM-DUO settings menu list. To enter the settings menu mode, press the key. Use E2 to select the menu, then apply a short pressure on E2 to display the current menu setting, if you want to change the setting use the E2 knob and confirm the setting with a short pressure on E2 Menu Title Description Available Settings Default 1 RX ATT Receiver input attenuation OFF or ON OFF 2 RX LP Receiver low pass filter status OFF or ON ON 3 SNAP Round to step OFF or ON ON 4 AGC TH AGC Threshold From 0 to 10 4 6 AUX VOL Auxiliary output volume From 0 to 100 50 7 QUICKSTEP Step selected for the “QuickStep” mode 1Hz, 5Hz, 10Hz, 25Hz, 50Hz, 100Hz, 250Hz, 500Hz, 1kHz, 2kHz, 3kHz, 4.5kHz, 5kHz, 7.5kHz, 9kHz, 10kHz, 12.5kHz, 25kHz, 50kHz, 100kHz, 125kHz, 250kHz, 500kHz, 1MHz 1kHz 8 CW MUTE Set mute status during CW transmission OFF or ON OFF 9 xSB MUTE Set mute status during AM or SSB transmission OFF or ON ON 10 FILBYPASS Set pre-selection filters bypass, active only in reception in remote/mixed mode and in split mode OFF or ON OFF 11 TONE VOL Sidetone volume From 0 to 100 5 30 TX ENABLE Enable the transmission OFF or ON ON 31 ANTENNAS Number of antenna used 1 or 2 1 32 TX IN Transmission input in AM and SSB Microphone or USB soundcard Microphone 33 TXOUT Transmission output selection PWR (ant. RTX) or 0dBm (RFOUT) PWR 34 TX POWER Transmission power selection 0.3W, 0.5W, 1W, 1.2W, 1.5W, 2W, 3W, 4W, 5W or max available 5W 35 TX BW Transmission filter selection 50Hz - 4000Hz 100Hz - 2700Hz 100Hz - 3000Hz 100Hz - 3500Hz 100Hz - 4000Hz 200Hz - 2700Hz 200Hz - 3000Hz 200Hz - 3500Hz 200Hz - 4000Hz 300Hz - 2700Hz 300Hz - 3000Hz 300Hz - 3500Hz 300Hz - 4000Hz 100Hz - 2700Hz
ELAD FDM-DUO User Manual Rev 1.04 10/2014 © 2014 ELAD S.r.l. All rights reserved. No part of this document may be reproduced, published, used, disclosed or disseminated in any form or by any means, electronic, photocopying or otherwise, without prior written permission of ELAD S.r.l. 24 36 MIC GAIN Microphone Gain ±12dB in step of 0.5dB 0dB 37 CW IN CW transmission input selection Key or Paddle Key 38 CW DELAY PTT release delay in CW 0 to 1000ms 240ms 39 CW KEY Select where the key is connected on the key/paddle jack TIP or RING TIP 40 CW TIP Select the dot or dash on the tip of the key/paddle jack DOT or DASH DASH 41 CW IAMBIC Set the iambic mode A or B A 42 CW RX WPM CW characters decoding speed 5 to 90 words per minute 12 43 TX RX TH CW threshold for a tone recognition AUTO or from 1 to 10 AUTO 44 CW DECODE Enable/Disable the automatic CW decoding OFF or ON OFF 45 CW TX WPM CW transmission speed 5 to 90 words per minute 10 46 CW MSG CW Message selection Msg 1 to Msg 10 Msg 1 47 TX VIEW Select the default parameter to be displayed during a transmission Frequency, forward power, reflected power, SWR Forward power 48 UP/DOWN ACC MIC UP / DOWN acceleration of the microphone buttons 1, 2, 3 2 49 TUNE TIME Antenna tuning mode timeout. Active only if the selected transmission output is the antenna. Not active in service mode 10 to 120 seconds 10s 50 ATT ON TX Attenuation in transmission mode OFF or ON OFF 60 FR OFFSET Enable / Disable the frequency offset for the visualization OFF or ON OFF 61 OFS VALUE Frequency offset value for the visualization +/- 99.999999999 GHz. See * 0Hz 62 F4 Button Select the F4 key function when a long pressure is applied None / Send CW Message / Split mode None 70 CAT BAUD CAT serial port baud rate 9600, 38400, 57600, 115200 38400 71 HOLD TIME Hold time to detect a long pressure From 500 to 2500ms 1000ms 72 REPT TIME Repetition time when a key is pressed From 100 to 1500ms 600ms 80 SERVICE Enable Service mode ON or OFF OFF 81 DEFAULT Restore default parameters YES or NO NO 82 UI UPDATE If Service mode is active, enable the firmware update mode YES or NO NO 83 VIEW SN Display the FDM-DUO serial number 84 VIEW FW Display the FDM-DUO firmware versions Firmware UI
ELAD FDM-DUO User Manual Rev 1.04 10/2014 © 2014 ELAD S.r.l. All rights reserved. No part of this document may be reproduced, published, used, disclosed or disseminated in any form or by any means, electronic, photocopying or otherwise, without prior written permission of ELAD S.r.l. 25 6.6.1 Frequency offset menu The Frequency offset set in digit by digit mode with some improvements to set a signed 10 digit offset in a 9 digit display.  E2: Select the digit to modify  Main encoder: modify the selected digit value  E1: change the visualization o kHz: the 8 most significant digit of the frequency offset are displayed o Hz: the 8 least significant digit of the frequency offset are displayed  E1 or Main encoder short pressure: change the sign of the offset (+/-)  E2 short pressure: save the setting EXAMPLES: Frequency offset value: +10,000,034,120 Hz o kHz Display mode o Hz Display mode
ELAD FDM-DUO User Manual Rev 1.04 10/2014 © 2014 ELAD S.r.l. All rights reserved. No part of this document may be reproduced, published, used, disclosed or disseminated in any form or by any means, electronic, photocopying or otherwise, without prior written permission of ELAD S.r.l. 26 7 CAT Remote Control 7.1 Introduction The FDM-DUO transceiver uses a full-duplex, asynchronous, USB serial interface for communicating through the USB CAT port. Each data is constructed with 1 start bit, 8 data bits, 1 stop bit, no parity is used (8N1). The baud rate is selectable in the [40] CAT BAUD menu. Available values are 9600, 38400, 57600, 115200 bps. The FDM-DUO implement a subset of the Kenwood TS-480 command set. Some command have a dummy implementation for compatibility issues with Ham Radio Deluxe. 7.2 Computer control commands A computer control command is composed of an alphabetical command, various parameters, and the terminator that signals the of the command. For example to set the VFO-A to 14MHz the command is: FA00014000000;  “FA”: alphabetical command  “00014000000000”: parameter  “;”: terminator Computer control commands can be classified as shown below: EXAMPLE  To set the VFO-A to 14MHz the PC sends: “FA00014000000000;” SET command  To read the VFO-A frequency the PC sends: “FA;” READ command  When this command has been sent, the following message is returned to the PC: “FA00014000000000;” ANSWER Computer control commands Input PC->FDM-DUO SET (set a parameter) READ (read a condition) Output FDM-DUO->PC ANSWER (transmit a condition)
ELAD FDM-DUO User Manual Rev 1.04 10/2014 © 2014 ELAD S.r.l. All rights reserved. No part of this document may be reproduced, published, used, disclosed or disseminated in any form or by any means, electronic, photocopying or otherwise, without prior written permission of ELAD S.r.l. 27 7.3 FDM-DUO CAT commands list 7.3.1 Active commands table FA Reads and sets the VFO A frequency Parameters: P1: Frequency in Hz (11 digit) Set 1 2 3 4 5 6 7 8 9 10 F A P1 P1 P1 P1 P1 P1 P1 P1 11 12 13 14 15 16 17 18 19 20 P1 P1 P1 ; Read 1 2 3 4 5 6 7 8 9 10 F A ; Answer 1 2 3 4 5 6 7 8 9 10 F A P1 P1 P1 P1 P1 P1 P1 P1 1 2 3 4 5 6 7 8 9 10 P1 P1 P1 ; FB Reads and sets the VFO B frequency Parameters: P1: Frequency in Hz (11 digit) Set 1 2 3 4 5 6 7 8 9 10 F B P1 P1 P1 P1 P1 P1 P1 P1 11 12 13 14 15 16 17 18 19 20 P1 P1 P1 ; Read 1 2 3 4 5 6 7 8 9 10 F B ; Answer 1 2 3 4 5 6 7 8 9 10 F B P1 P1 P1 P1 P1 P1 P1 P1 1 2 3 4 5 6 7 8 9 10 P1 P1 P1 ; FR Selects or reads the receiver VFO or M.CH mode Parameters: P1 0: VFO-A 1: VFO-B 2: M.CH Set 1 2 3 4 5 6 7 8 9 10 F R P1 ; Read 1 2 3 4 5 6 7 8 9 10 F R ; Answer 1 2 3 4 5 6 7 8 9 10 F R P1 ; FT Selects or reads the transmitter VFO or M.CH mode Parameters: P1 0: VFO-A 1: VFO-B 2: M.CH Set 1 2 3 4 5 6 7 8 9 10 F R P1 ; Read 1 2 3 4 5 6 7 8 9 10 F R ; Answer 1 2 3 4 5 6 7 8 9 10 F R P1 ;
ELAD FDM-DUO User Manual Rev 1.04 10/2014 © 2014 ELAD S.r.l. All rights reserved. No part of this document may be reproduced, published, used, disclosed or disseminated in any form or by any means, electronic, photocopying or otherwise, without prior written permission of ELAD S.r.l. 28 IF Retrieves the transceiver status Parameters: P1: Frequency 11 digit P2: 5 spaces P3: Always 0 P4: Always 0 P5: Always 0 P6: Always 0 P7: Memory ch. Number 0-99 P8: 0:Rx 1:Tx P9: Operating Mode (See MD) P10: See FR, FT P11: Always 0 P12 0:Normal 1:Split P13: Always 0 P14: Always 0 P15: Space Set 1 2 3 4 5 6 7 8 9 10 Read 1 2 3 4 5 6 7 8 9 10 I F ; Answer 1 2 3 4 5 6 7 8 9 10 I F P1 P1 P1 P1 P1 P1 P1 P1 11 12 13 14 15 16 17 18 19 20 P1 P1 P1 P2 P2 P2 P2 P2 P3 P3 21 22 23 24 25 26 27 28 29 30 P3 P3 P3 P4 P5 P6 P7 P7 P8 P9 31 32 33 34 35 36 37 38 39 40 P10 P11 P12 P13 P14 P14 P15 ; MC Recalls or reads the Memory channel Parameters: P1: 0 or 1 P2: 00 to 99 Set 1 2 3 4 5 6 7 8 9 10 M C P1 P2 P2 ; Read 1 2 3 4 5 6 7 8 9 10 M C ; Answer 1 2 3 4 5 6 7 8 9 10 M C P1 P2 P1 ; MD Recalls or reads the operating mode status Parameters: P1: 1: LSB 2: USB 3: CW 5: AM Set 1 2 3 4 5 6 7 8 9 10 M D P1 ; Read 1 2 3 4 5 6 7 8 9 10 M D ; Answer 1 2 3 4 5 6 7 8 9 10 M D P1 ;
ELAD FDM-DUO User Manual Rev 1.04 10/2014 © 2014 ELAD S.r.l. All rights reserved. No part of this document may be reproduced, published, used, disclosed or disseminated in any form or by any means, electronic, photocopying or otherwise, without prior written permission of ELAD S.r.l. 29 MR Reads the Memory channel data P1:0 P2: 0 P3: 00 to 99 Memory No. P4: Frequency (11 digit) P5: Mode P6: Always 0 P7: Always 0 P8: Always 0 P9: Always 0 P10: Memory label, last 14 chars P11: Always 0 P12: Always 0 P13: Always 000000000 P14: Step size P15: Memory status B: used F: free P16: Memory label, first 8 chars Set 1 2 3 4 5 6 7 8 9 10 Read 1 2 3 4 5 6 7 8 9 10 M R P1 P2 P3 P3 Answer 1 2 3 4 5 6 7 8 9 10 M R P1 P2 P3 P3 P4 P4 P4 P4 11 12 13 14 15 16 17 18 19 20 P4 P4 P4 P4 P4 P4 P4 P5 P6 P7 21 22 23 24 25 26 27 28 29 30 P8 P8 P9 P9 P10 P10 P10 P10 P10 P10 31 32 33 34 35 36 37 38 39 40 P10 P10 P10 P10 P10 P10 P10 P10 P11 P12 41 42 43 44 45 46 47 48 49 50 P15 P16 P16 P16 P16 P16 P16 P16 P16 ; MW Store the data to the Memory channel P1:0 P2: 0 P3: 00 to 99 Memory No. P4: Frequency (11 digit) P5: Mode P6: Always 0 P7: Always 0 P8: Always 0 P9: Always 0 P10: Memory label, last 14 chars P11: Always 0 P12: Always 0 P13: Always 000000000 P14: Step size P15: Memory status B: used F: free P16: Memory label, first 8 chars Set 1 2 3 4 5 6 7 8 9 10 M W P1 P2 P3 P3 P4 P4 P4 P4 11 12 13 14 15 16 17 18 19 20 P4 P4 P4 P4 P4 P4 P4 P5 P6 P7 21 22 23 24 25 26 27 28 29 30 P8 P8 P9 P6 P10 P10 P10 P10 P10 P10 31 32 33 34 35 36 37 38 39 40 P10 P10 P10 P10 P10 P10 P10 P10 P11 P12 41 42 43 44 45 46 47 48 49 50 P15 P16 P16 P16 P16 P16 P16 P16 P16 ; Read 1 2 3 4 5 6 7 8 9 10 Answer 1 2 3 4 5 6 7 8 9 10 RX Sets the receiver function status Parameters: P1: Always 0 Set 1 2 3 4 5 6 7 8 9 10 R X ; Read 1 2 3 4 5 6 7 8 9 10 Answer 1 2 3 4 5 6 7 8 9 10 R X P1 ; TX Sets or reads the TF-SET function status Parameters: P1 0 P2 0 Set 1 2 3 4 5 6 7 8 9 10 T X P1 ; Read 1 2 3 4 5 6 7 8 9 10 Answer 1 2 3 4 5 6 7 8 9 10 T X P2 ;
ELAD FDM-DUO User Manual Rev 1.04 10/2014 © 2014 ELAD S.r.l. All rights reserved. No part of this document may be reproduced, published, used, disclosed or disseminated in any form or by any means, electronic, photocopying or otherwise, without prior written permission of ELAD S.r.l. 30 7.3.2 Dummy commands table The following commands have a dummy implementation. AC Sets or reads the internal antenna tuner status DUMMY IMPLEMENTATION Parameters: P1: Always 00 P2: Always 0 Set 1 2 3 4 5 6 7 8 9 10 Read 1 2 3 4 5 6 7 8 9 10 A C ; Answer 1 2 3 4 5 6 7 8 9 10 A C P1 P1 P2 ; AG Sets or reads the AF gain DUMMY IMPLEMENTATION Parameters: P1: Always 0 P2: Always 000 Set 1 2 3 4 5 6 7 8 9 10 Read 1 2 3 4 5 6 7 8 9 10 A G P1 ; Answer 1 2 3 4 5 6 7 8 9 10 A G P1 P2 P2 P2; AI Sets or reads the Auto Information (AI) function ON/ OFF DUMMY IMPLEMENTATION Parameters: P1: Always 0 Set 1 2 3 4 5 6 7 8 9 10 Read 1 2 3 4 5 6 7 8 9 10 A I P1 ; Answer 1 2 3 4 5 6 7 8 9 10 A I P1 ; AN Selects the antenna connector ANT1/ ANT2 DUMMY IMPLEMENTATION Parameters: P1: Always 1 Set 1 2 3 4 5 6 7 8 9 10 Read 1 2 3 4 5 6 7 8 9 10 A N ; Answer 1 2 3 4 5 6 7 8 9 10 A N P1 ; BC Sets or reads the Beat Canceller function status DUMMY IMPLEMENTATION Parameters: P1: Always 0 Set 1 2 3 4 5 6 7 8 9 10 Read 1 2 3 4 5 6 7 8 9 10 B C ; Answer 1 2 3 4 5 6 7 8 9 10 B C P1 ;
ELAD FDM-DUO User Manual Rev 1.04 10/2014 © 2014 ELAD S.r.l. All rights reserved. No part of this document may be reproduced, published, used, disclosed or disseminated in any form or by any means, electronic, photocopying or otherwise, without prior written permission of ELAD S.r.l. 31 BY Reads the busy signal status DUMMY IMPLEMENTATION Parameters: P1: Always 0 P2: Always 0 Set 1 2 3 4 5 6 7 8 9 10 Read 1 2 3 4 5 6 7 8 9 10 B Y ; Answer 1 2 3 4 5 6 7 8 9 10 B Y P1 P2 ; CA Sets and reads the CW Auto Zero-beat function status DUMMY IMPLEMENTATION Parameters: P1: Always 0 Set 1 2 3 4 5 6 7 8 9 10 Read 1 2 3 4 5 6 7 8 9 10 C A ; Answer 1 2 3 4 5 6 7 8 9 10 C A P1 ; CN Sets and reads the CTCSS tone number DUMMY IMPLEMENTATION Parameters: P1: Always 00 Set 1 2 3 4 5 6 7 8 9 10 Read 1 2 3 4 5 6 7 8 9 10 C N ; Answer 1 2 3 4 5 6 7 8 9 10 C A P1 P1 ; CT Sets and reads the CTCSS function status DUMMY IMPLEMENTATION Parameters: P1: Always 0 Set 1 2 3 4 5 6 7 8 9 10 Read 1 2 3 4 5 6 7 8 9 10 C T ; Answer 1 2 3 4 5 6 7 8 9 10 C T P1 ; DL Sets and reads the Digital Noise Limiter (DNL) function status DUMMY IMPLEMENTATION Parameters: P1: Always 0 P2: Always 00 Set 1 2 3 4 5 6 7 8 9 10 Read 1 2 3 4 5 6 7 8 9 10 D L ; Answer 1 2 3 4 5 6 7 8 9 10 D L P1 P2 P2 ; EX Sets or reads the Extension Menu DUMMY IMPLEMENTATION Parameters: P1: 000 - 060: Menu No. P2: Always 00 P3: Always 0 P4: Always 0 P5: Always 0 Set 1 2 3 4 5 6 7 8 9 10 Read 1 2 3 4 5 6 7 8 9 10 E X P1 P1 P1 P2 P2 P3 P4 ; Answer 1 2 3 4 5 6 7 8 9 10 E X P1 P1 P1 P2 P2 P3 P4 P5 11 12 13 14 15 16 17 18 19 20 P5 ;
ELAD FDM-DUO User Manual Rev 1.04 10/2014 © 2014 ELAD S.r.l. All rights reserved. No part of this document may be reproduced, published, used, disclosed or disseminated in any form or by any means, electronic, photocopying or otherwise, without prior written permission of ELAD S.r.l. 32 FS Selects or reads the Fine Tuning function status DUMMY IMPLEMENTATION Parameters: P1 Always 0 Set 1 2 3 4 5 6 7 8 9 10 Read 1 2 3 4 5 6 7 8 9 10 F S ; Answer 1 2 3 4 5 6 7 8 9 10 F S P1 ; FW Selects or reads the DSP filtering bandwidth DUMMY IMPLEMENTATION Parameters: P1 Always 0000 Set 1 2 3 4 5 6 7 8 9 10 Read 1 2 3 4 5 6 7 8 9 10 F W ; Answer 1 2 3 4 5 6 7 8 9 10 F W P1 P1 P1 P1 ; GT Selects or reads the DSP filtering bandwidth DUMMY IMPLEMENTATION Parameters: P1 Always 000 Set 1 2 3 4 5 6 7 8 9 10 Read 1 2 3 4 5 6 7 8 9 10 G T ; Answer 1 2 3 4 5 6 7 8 9 10 G T P1 P1 P1 ; IS Sets and reads the IF SHIFT function status DUMMY IMPLEMENTATION Parameters: P1: “+” P2: Always 0000 Set 1 2 3 4 5 6 7 8 9 10 Read 1 2 3 4 5 6 7 8 9 10 I S ; Answer 1 2 3 4 5 6 7 8 9 10 I S P1 P2 P2 P2 P2 ; KS Sets and reads the CW electric keyer’s keying speed DUMMY IMPLEMENTATION Parameters: P1: 010 Set 1 2 3 4 5 6 7 8 9 10 Read 1 2 3 4 5 6 7 8 9 10 K S ; Answer 1 2 3 4 5 6 7 8 9 10 K S P1 P1 P1 ; MF Sets or reads Menu A or B DUMMY IMPLEMENTATION Parameters: P1: Always 0 Set 1 2 3 4 5 6 7 8 9 10 Read 1 2 3 4 5 6 7 8 9 10 M F ; Answer 1 2 3 4 5 6 7 8 9 10 M F P1 ;
ELAD FDM-DUO User Manual Rev 1.04 10/2014 © 2014 ELAD S.r.l. All rights reserved. No part of this document may be reproduced, published, used, disclosed or disseminated in any form or by any means, electronic, photocopying or otherwise, without prior written permission of ELAD S.r.l. 33 MG Sets or reads the Microphone gain status DUMMY IMPLEMENTATION Parameters: P1: Always 000 Set 1 2 3 4 5 6 7 8 9 10 Read 1 2 3 4 5 6 7 8 9 10 M G ; Answer 1 2 3 4 5 6 7 8 9 10 M G P1 P1 P1 ; NB Set or reads the Noise Blanker (NB) function status DUMMY IMPLEMENTATION Parameters: P1: Always 0 Set 1 2 3 4 5 6 7 8 9 10 Read 1 2 3 4 5 6 7 8 9 10 N B ; Answer 1 2 3 4 5 6 7 8 9 10 N B P1 ; NL Set or reads the NB (Noise Blanker) level DUMMY IMPLEMENTATION Parameters: P1: Always 0 Set 1 2 3 4 5 6 7 8 9 10 Read 1 2 3 4 5 6 7 8 9 10 N L ; Answer 1 2 3 4 5 6 7 8 9 10 N L P1 P1 P1 ; NR Sets or reads the Noise Reduction (NR) function status DUMMY IMPLEMENTATION Parameters: P1: Always 0 Set 1 2 3 4 5 6 7 8 9 10 Read 1 2 3 4 5 6 7 8 9 10 N R ; Answer 1 2 3 4 5 6 7 8 9 10 N R P1 ; PA Sets or reads the pre-amplifier function status DUMMY IMPLEMENTATION Parameters: P1: Always 0 P2: Always 0 Set 1 2 3 4 5 6 7 8 9 10 Read 1 2 3 4 5 6 7 8 9 10 P A ; Answer 1 2 3 4 5 6 7 8 9 10 P A P1 P2 ; PC Sets or reads the output power DUMMY IMPLEMENTATION Parameters: P1: Always 005 Set 1 2 3 4 5 6 7 8 9 10 Read 1 2 3 4 5 6 7 8 9 10 P C ; Answer 1 2 3 4 5 6 7 8 9 10 P C P1 P1 P1 ;
ELAD FDM-DUO User Manual Rev 1.04 10/2014 © 2014 ELAD S.r.l. All rights reserved. No part of this document may be reproduced, published, used, disclosed or disseminated in any form or by any means, electronic, photocopying or otherwise, without prior written permission of ELAD S.r.l. 34 PR Sets or reads the Speech Processor function ON/ OFF DUMMY IMPLEMENTATION Parameters: P1: Always 0 Set 1 2 3 4 5 6 7 8 9 10 Read 1 2 3 4 5 6 7 8 9 10 P R ; Answer 1 2 3 4 5 6 7 8 9 10 P R P1 ; PS Sets or reads the Power ON/ OFF status DUMMY IMPLEMENTATION Parameters: P1: Always 1 Set 1 2 3 4 5 6 7 8 9 10 Read 1 2 3 4 5 6 7 8 9 10 P S ; Answer 1 2 3 4 5 6 7 8 9 10 P S P1 ; QR Sets or reads the Quick Memory channel data DUMMY IMPLEMENTATION Parameters: P1: Always 0 P2: Always 0 Set 1 2 3 4 5 6 7 8 9 10 Read 1 2 3 4 5 6 7 8 9 10 Q R ; Answer 1 2 3 4 5 6 7 8 9 10 Q R P1 P2 ; RA Sets or reads the Attenuator function status DUMMY IMPLEMENTATION Parameters: P1: Always 00 P2: Always 00 Set 1 2 3 4 5 6 7 8 9 10 Read 1 2 3 4 5 6 7 8 9 10 R A ; Answer 1 2 3 4 5 6 7 8 9 10 R A P1 P1 P2 P2 ; RG Sets or read the RF gain status DUMMY IMPLEMENTATION Parameters: P1: Always 000 Set 1 2 3 4 5 6 7 8 9 10 Read 1 2 3 4 5 6 7 8 9 10 R G ; Answer 1 2 3 4 5 6 7 8 9 10 R G P1 P1 P1 ; RL Sets or reads the Noise Reduction level DUMMY IMPLEMENTATION Parameters: P1: Always 0 Set 1 2 3 4 5 6 7 8 9 10 Read 1 2 3 4 5 6 7 8 9 10 R L ; Answer 1 2 3 4 5 6 7 8 9 10 R L P1 ;
ELAD FDM-DUO User Manual Rev 1.04 10/2014 © 2014 ELAD S.r.l. All rights reserved. No part of this document may be reproduced, published, used, disclosed or disseminated in any form or by any means, electronic, photocopying or otherwise, without prior written permission of ELAD S.r.l. 35 SD Sets or reads the CW Break-in time delay DUMMY IMPLEMENTATION Parameters: P1: Always 0000 Set 1 2 3 4 5 6 7 8 9 10 Read 1 2 3 4 5 6 7 8 9 10 S D ; Answer 1 2 3 4 5 6 7 8 9 10 S D P1 P1 P1 P1 ; SH Sets or reads the DSP filter settings DUMMY IMPLEMENTATION Parameters: P1: Always 00 Set 1 2 3 4 5 6 7 8 9 10 Read 1 2 3 4 5 6 7 8 9 10 S H ; Answer 1 2 3 4 5 6 7 8 9 10 S H P1 P1 ; SL Sets or reads the DSP filter settings DUMMY IMPLEMENTATION Parameters: P1: Always 00 Set 1 2 3 4 5 6 7 8 9 10 Read 1 2 3 4 5 6 7 8 9 10 S H ; Answer 1 2 3 4 5 6 7 8 9 10 S H P1 P1 ; SM Reads the S-meter status DUMMY IMPLEMENTATION Parameters: P1: Always 0 P2: Always 0000 Set 1 2 3 4 5 6 7 8 9 10 Read 1 2 3 4 5 6 7 8 9 10 S M P1 ; Answer 1 2 3 4 5 6 7 8 9 10 S M P1 P2 P2 P2 P2 ; SQ Sets and reads the squelch level DUMMY IMPLEMENTATION Parameters: P1: Always 0 P2: Always 0000 Set 1 2 3 4 5 6 7 8 9 10 Read 1 2 3 4 5 6 7 8 9 10 S Q P1 ; Answer 1 2 3 4 5 6 7 8 9 10 S Q P1 P2 P2 P2 ; TN Sets or reads the Tone frequency number DUMMY IMPLEMENTATION Parameters: P1: Always 00 Set 1 2 3 4 5 6 7 8 9 10 Read 1 2 3 4 5 6 7 8 9 10 T N ; Answer 1 2 3 4 5 6 7 8 9 10 T N P1 P1 ;
ELAD FDM-DUO User Manual Rev 1.04 10/2014 © 2014 ELAD S.r.l. All rights reserved. No part of this document may be reproduced, published, used, disclosed or disseminated in any form or by any means, electronic, photocopying or otherwise, without prior written permission of ELAD S.r.l. 36 TO Sets or reads the Tone function ON/ OFF DUMMY IMPLEMENTATION Parameters: P1: Always 0 Set 1 2 3 4 5 6 7 8 9 10 Read 1 2 3 4 5 6 7 8 9 10 T O ; Answer 1 2 3 4 5 6 7 8 9 10 T O P1 ; TS Sets or reads the TF-SET function status DUMMY IMPLEMENTATION Parameters: P1: Always 0 Set 1 2 3 4 5 6 7 8 9 10 Read 1 2 3 4 5 6 7 8 9 10 T S ; Answer 1 2 3 4 5 6 7 8 9 10 T S P1 ; VD Sets or reads the VOX delay time DUMMY IMPLEMENTATION Parameters: P1: Always 0000 Set 1 2 3 4 5 6 7 8 9 10 Read 1 2 3 4 5 6 7 8 9 10 V D ; Answer 1 2 3 4 5 6 7 8 9 10 V D P1 P1 P1 P1 ; VG Sets or reads the VOX GAIN DUMMY IMPLEMENTATION Parameters: P1: Always 000 Set 1 2 3 4 5 6 7 8 9 10 Read 1 2 3 4 5 6 7 8 9 10 V G ; Answer 1 2 3 4 5 6 7 8 9 10 V G P1 P1 P1 ; VX Sets or reads the VOX function status DUMMY IMPLEMENTATION Parameters: P1: Always 0 Set 1 2 3 4 5 6 7 8 9 10 Read 1 2 3 4 5 6 7 8 9 10 V X ; Answer 1 2 3 4 5 6 7 8 9 10 V X P1 ;
ELAD FDM-DUO User Manual Rev 1.04 10/2014 © 2014 ELAD S.r.l. All rights reserved. No part of this document may be reproduced, published, used, disclosed or disseminated in any form or by any means, electronic, photocopying or otherwise, without prior written permission of ELAD S.r.l. 37 8 Software & Driver Installation 8.1 Software installation in Windows 8 Windows 7 and Windows XP 8.1.1 First-time install in Windows 8 and Windows 7 Double-click the file “setup.exe” in the CD . The windows installer first installs the prerequisites:  Microsoft VC++ 2010 Runtime libraries  Microsoft .NET Framework 4.0 (Only for Windows 7) and then the FDM-SW2 software.  Click on “Accept” (Only for Windows 7)
ELAD FDM-DUO User Manual Rev 1.04 10/2014 © 2014 ELAD S.r.l. All rights reserved. No part of this document may be reproduced, published, used, disclosed or disseminated in any form or by any means, electronic, photocopying or otherwise, without prior written permission of ELAD S.r.l. 38 Click on “Install” Click on “Yes” Click on Install
ELAD FDM-DUO User Manual Rev 1.04 10/2014 © 2014 ELAD S.r.l. All rights reserved. No part of this document may be reproduced, published, used, disclosed or disseminated in any form or by any means, electronic, photocopying or otherwise, without prior written permission of ELAD S.r.l. 39 Microsoft Visual C++ 2010 x86 Redistributable installation is complete, click on “Finish” Click on “Yes” to start the installation of the .Net Framework 4.0 (Only for Windows 7)
ELAD FDM-DUO User Manual Rev 1.04 10/2014 © 2014 ELAD S.r.l. All rights reserved. No part of this document may be reproduced, published, used, disclosed or disseminated in any form or by any means, electronic, photocopying or otherwise, without prior written permission of ELAD S.r.l. 40 Click to “Next” to start the FDM-SW2 software installation Chose the installation folder, then click on “Next”
ELAD FDM-DUO User Manual Rev 1.04 10/2014 © 2014 ELAD S.r.l. All rights reserved. No part of this document may be reproduced, published, used, disclosed or disseminated in any form or by any means, electronic, photocopying or otherwise, without prior written permission of ELAD S.r.l. 41 Click on “Next” Click on “Yes”
ELAD FDM-DUO User Manual Rev 1.04 10/2014 © 2014 ELAD S.r.l. All rights reserved. No part of this document may be reproduced, published, used, disclosed or disseminated in any form or by any means, electronic, photocopying or otherwise, without prior written permission of ELAD S.r.l. 42 8.1.2 First-time install in Windows XP Double-click the file “setup.exe” in the installation folder. Click on “Accept”
ELAD FDM-DUO User Manual Rev 1.04 10/2014 © 2014 ELAD S.r.l. All rights reserved. No part of this document may be reproduced, published, used, disclosed or disseminated in any form or by any means, electronic, photocopying or otherwise, without prior written permission of ELAD S.r.l. 43 Click on “Install” Click on “Install”
ELAD FDM-DUO User Manual Rev 1.04 10/2014 © 2014 ELAD S.r.l. All rights reserved. No part of this document may be reproduced, published, used, disclosed or disseminated in any form or by any means, electronic, photocopying or otherwise, without prior written permission of ELAD S.r.l. 44 Click on Next to install the FDM-SW2 software Select the installation folder, then click on “Next”
ELAD FDM-DUO User Manual Rev 1.04 10/2014 © 2014 ELAD S.r.l. All rights reserved. No part of this document may be reproduced, published, used, disclosed or disseminated in any form or by any means, electronic, photocopying or otherwise, without prior written permission of ELAD S.r.l. 45 Click on “Next” The FDM-SW2 Software installation is completed
ELAD FDM-DUO User Manual Rev 1.04 10/2014 © 2014 ELAD S.r.l. All rights reserved. No part of this document may be reproduced, published, used, disclosed or disseminated in any form or by any means, electronic, photocopying or otherwise, without prior written permission of ELAD S.r.l. 46 8.1.3 Update an existing software version Double click on file ELAD_FDM_SW2_V_x.xx.msi included in the update and follow the instructions.
ELAD FDM-DUO User Manual Rev 1.04 10/2014 © 2014 ELAD S.r.l. All rights reserved. No part of this document may be reproduced, published, used, disclosed or disseminated in any form or by any means, electronic, photocopying or otherwise, without prior written permission of ELAD S.r.l. 47 8.2 FDM-DUO USB driver 8.2.1 FDM-DUO USB driver installation in Windows 8 and Windows 7 8.2.1.1 First driver installation To install ELAD FDM-DUO driver, connect FDM-DUO USB RX port to a USB 2.0 socket on PC end power on the device. When Windows detects the new hardware, follow the steps listed below to install driver correctly: Open Control Panel from Start menu, select “System” and “Device Manager”. Expand “Other Devices” node: FDM-DUO. Select FDM-DUO, right click on it and execute “Update driver software”.
ELAD FDM-DUO User Manual Rev 1.04 10/2014 © 2014 ELAD S.r.l. All rights reserved. No part of this document may be reproduced, published, used, disclosed or disseminated in any form or by any means, electronic, photocopying or otherwise, without prior written permission of ELAD S.r.l. 48 When Windows starts the installation procedure, select the option “Browse my computer for driver software” (the second option). In the next dialog-box, insert the driver folder location using “Browse” button and check the option “Include subfolders”. In this way manual driver search is enabled For 32 bit system select the folder: C:\Program Files\ELAD\ELAD FDM-SW2\ELAD_FDM_Driver For 64 bit system select the folder: C:\Program Files (x86)\ ELAD\ELAD FDM-SW2\ELAD_FDM_Driver Then click “Next”. Click Install.
ELAD FDM-DUO User Manual Rev 1.04 10/2014 © 2014 ELAD S.r.l. All rights reserved. No part of this document may be reproduced, published, used, disclosed or disseminated in any form or by any means, electronic, photocopying or otherwise, without prior written permission of ELAD S.r.l. 49 Let the hardware installation automatically completes and, at the procedure ending, click on “Close”; then disconnect and connect FDM-DUO device on the same USB socket. Now ELAD FDM-DUO USB driver is installed on your PC.
ELAD FDM-DUO User Manual Rev 1.04 10/2014 © 2014 ELAD S.r.l. All rights reserved. No part of this document may be reproduced, published, used, disclosed or disseminated in any form or by any means, electronic, photocopying or otherwise, without prior written permission of ELAD S.r.l. 50 8.2.2 FDM-S2 USB driver installation in Windows XP 8.2.2.1 First driver installation To install ELAD FDM-DUO driver, connect FDM-DUO USB RX port to a USB 2.0 socket on PC and power on the device. Windows XP detects the new hardware and starts the hardware installation wizard. Then, next steps to install FDM-DUO driver are listed below: At the first dialog box, select the last option “No, not this time” and “Next”. Select “Install from a list or specific location (Advanced)” and “Next”. In the next dialog-box, check the options “Search for the best driver in these location” and “Include this location in the search” to enable manual driver search. Clicking on “Browse”, select the path where the driver folder is located: Local Drive (C:) \Programs\ELAD\ELAD FDM-SW2\ELAD_FDM_Driver. Then click “Next”.
ELAD FDM-DUO User Manual Rev 1.04 10/2014 © 2014 ELAD S.r.l. All rights reserved. No part of this document may be reproduced, published, used, disclosed or disseminated in any form or by any means, electronic, photocopying or otherwise, without prior written permission of ELAD S.r.l. 51 Let the hardware installation automatically completes and click on “Finish”; then disconnect and connect FDM- DUO device on the same USB socket. Now ELAD FDM- DUO driver is installed on your PC. 8.2.2.1 Driver installation verify in Windows 8 and Windows 7 To verify FDM-DUO driver current version, connect the device to USB socket (where the device driver is already installed) and power on the device. Then open Control Panel from Start menu. Click on “System” and select “Device Manager”. Expanding “ELAD Samplers” node, right click on “ELAD FDM-DUO” and select “Properties”.
ELAD FDM-DUO User Manual Rev 1.04 10/2014 © 2014 ELAD S.r.l. All rights reserved. No part of this document may be reproduced, published, used, disclosed or disseminated in any form or by any means, electronic, photocopying or otherwise, without prior written permission of ELAD S.r.l. 52 When dialog box opens, select “Driver” label: you must read provider name, current driver release date and current driver version. The figure shows an old FDM- DUO driver version. 8.2.2.2 Manual driver update To update FDM-DUO driver, connect the device to USB RX socket (where the device driver is already installed) and power on the device. Then open Control Panel from Start menu. Click on “System” and select “Device Manager”. Under “ELAD samplers” list select “ELAD FDM-DUO”, right click on it and execute “Update driver”.
ELAD FDM-DUO User Manual Rev 1.04 10/2014 © 2014 ELAD S.r.l. All rights reserved. No part of this document may be reproduced, published, used, disclosed or disseminated in any form or by any means, electronic, photocopying or otherwise, without prior written permission of ELAD S.r.l. 53 When Windows starts the installation procedure, select the last option “Browse my computer for driver software”. In the next dialog-box, disable the option “Include subfolders” and choose “Let me pick from a list of device drivers on my computer”. Don’t click “Next”.
ELAD FDM-DUO User Manual Rev 1.04 10/2014 © 2014 ELAD S.r.l. All rights reserved. No part of this document may be reproduced, published, used, disclosed or disseminated in any form or by any means, electronic, photocopying or otherwise, without prior written permission of ELAD S.r.l. 54 Verify that “Show compatible hardware” option is checked and ELAD FDM-DUO is selected: then click on “Have a Disk”. In this way the manual driver update is enabled. Don’t click “Next”. Click on “Browse” and search for FDM-DUO driver update folder location; then open winusb_fdmsampler.inf file. Click “OK” and then “Next”. Let the hardware installation automatically completes and, at the procedure ending, click on “Close”; then disconnect and connect FDM-DUO device on the same USB socket.
ELAD FDM-DUO User Manual Rev 1.04 10/2014 © 2014 ELAD S.r.l. All rights reserved. No part of this document may be reproduced, published, used, disclosed or disseminated in any form or by any means, electronic, photocopying or otherwise, without prior written permission of ELAD S.r.l. 55 To verify that a correct update is done, enter “Device Manager” in Control Panel; under “ELAD samplers” label select ELAD FDM-DUO driver (see sub-chapter Driver installation verify in Windows 8 and Windows 7): right click on it and choose “Properties”: select “Driver” label to visualize the last driver version (an example is depicted in figure below).
ELAD FDM-DUO User Manual Rev 1.04 10/2014 © 2014 ELAD S.r.l. All rights reserved. No part of this document may be reproduced, published, used, disclosed or disseminated in any form or by any means, electronic, photocopying or otherwise, without prior written permission of ELAD S.r.l. 56 8.2.2.3 Driver installation verify in Windows Xp To verify FDM-DUO driver current version, connect the device to USB socket (where the device driver is already installed) and open Control Panel from Start menu. Click on “System” and select “Device Manager” under “Hardware” label. Expanding “ELAD Samplers” node, right click on “ELAD FDM-DUO” and select “Properties”. When dialog box opens, select “Driver” label: you must read provider name, current driver release date and current driver version. The old ELAD FDM-DUO driver version is shown in figure below as example.
ELAD FDM-DUO User Manual Rev 1.04 10/2014 © 2014 ELAD S.r.l. All rights reserved. No part of this document may be reproduced, published, used, disclosed or disseminated in any form or by any means, electronic, photocopying or otherwise, without prior written permission of ELAD S.r.l. 57 8.2.2.4 Manual driver update in Windows Xp To update FDM-DUO driver, connect the device to USB socket (where the device driver is already installed) and power on the device. Then open Control Panel from Start menu. Click on “System” and select “Device Manager” under “Hardware” label. Select “ELAD FDM-DUO” from “ELAD Samplers” list, right click on it and execute “Update driver ” Now Windows XP launches the hardware update wizard: select the last option “No, not this time” and “Next”.
ELAD FDM-DUO User Manual Rev 1.04 10/2014 © 2014 ELAD S.r.l. All rights reserved. No part of this document may be reproduced, published, used, disclosed or disseminated in any form or by any means, electronic, photocopying or otherwise, without prior written permission of ELAD S.r.l. 58 At next step select “Install from a list or specific location (Advanced)” and “Next”. Then, disable all check-boxes that the system automatically sets and choose the last option for manual driver update, as depicted in figure. Select “Next”. Verify that “Show compatible hardware” option is checked and ELAD FDM-DUO is selected: then click on “Have a Disk”. Don’t click “Next”.
ELAD FDM-DUO User Manual Rev 1.04 10/2014 © 2014 ELAD S.r.l. All rights reserved. No part of this document may be reproduced, published, used, disclosed or disseminated in any form or by any means, electronic, photocopying or otherwise, without prior written permission of ELAD S.r.l. 59 Click on “Browse” and search for the FDM-DUO driver update folder location; then open winusb_fdmsampler.inf file, as depicted in figure. Click “OK” and then “Next”. Now driver update starts: at next dialog box select “Continue Anyway” and ignore the warning. Let the hardware update automatically completes and, at the procedure ending, click on “Finish”; then disconnect e connect FDM-DUO device on the same USB socket.
ELAD FDM-DUO User Manual Rev 1.04 10/2014 © 2014 ELAD S.r.l. All rights reserved. No part of this document may be reproduced, published, used, disclosed or disseminated in any form or by any means, electronic, photocopying or otherwise, without prior written permission of ELAD S.r.l. 60 To verify that a correct update is done, enter “Device Manager” from Control Panel; under “ELAD Samplers” list, select ELAD FDM-DUO driver (see chapter Driver installation verify in Windows Xp) right click on it and choose “Properties”. Select “Driver” label to visualize the last driver version (an example is depicted in figure below).
ELAD FDM-DUO User Manual Rev 1.04 10/2014 © 2014 ELAD S.r.l. All rights reserved. No part of this document may be reproduced, published, used, disclosed or disseminated in any form or by any means, electronic, photocopying or otherwise, without prior written permission of ELAD S.r.l. 61 8.2.3 FDM-DUO USB sound card Connect the TX USB port of FDM-DUO to a USB 2.0 port of the PC and power on the device. Then open the PC device manager. No driver installation is required for this device, just expand the node Audio inputs and outputs and check the FDM-DUO audio device.
ELAD FDM-DUO User Manual Rev 1.04 10/2014 © 2014 ELAD S.r.l. All rights reserved. No part of this document may be reproduced, published, used, disclosed or disseminated in any form or by any means, electronic, photocopying or otherwise, without prior written permission of ELAD S.r.l. 62 8.2.4 FDM-DUO USB CAT Serial port Connect the CAT USB port of FDM-DUO to a USB 2.0 port of the PC . Windows download and install automatically the FTDI FT232R serial port driver. When the installation process ends, open the windows device manager and check the FDM-DUO USB serial port in the node Ports (COM & LPT).
ELAD FDM-DUO User Manual Rev 1.04 10/2014 © 2014 ELAD S.r.l. All rights reserved. No part of this document may be reproduced, published, used, disclosed or disseminated in any form or by any means, electronic, photocopying or otherwise, without prior written permission of ELAD S.r.l. 63 9 Firmware update The following section describes how to update the firmware of the various components of the FDM-DUO. The latest versions for the User interface, Rx demodulator, Tx modulator, USB interface and FPGA are available here: http://sdr.eladit.com/FDM-DUO/Firmware Releases/. To ensure that the transceiver still working properly, please download the full update compressed archive named ELAD_FDM_DUO_Update_YYYY_MM_DD.zip (where YYYY_MM_DD are year, month and day of the release date). In this archive you can find the latest version of each firmware and also the latest version of the ELAD FDM-SW2 software. TO AVOID UPDATE ERRORS, PLEASE UPDATE THE “USER INTERFACE” FIRMWARE AFTER THE OTHERS FIRMWARE UPDATES 9.1 User interface firmware update Download the latest version of the UI firmware DISABLE ANY ANTIVIRUS PROGRAM BEFORE START THE FIRMWARE UPDATE In order to update the user interface (UI) firmware, you need to install the Flash Magic software. This program is available here: http://www.flashmagictool.com/ Turn on the ELAD FDM-DUO and connect the CAT USB serial port to a USB 2.0 port of your PC. Enable the FDM-DUO to perform a UI firmware update:  Press the key and select the menu “60 SERVICE”.  Press E2 to enter the setting, turn E2 to select ON then press E2 to store the setting.  Go to menu “62 UI Update”.  Press E2 to enter the setting, turn E2 to select YES then press E2 to store the setting. You need to identify the CAT USB COM port. Open the windows “Device Manager” and expand the COM port node. The CAT USB port is listed as “USB Serial Port”. In this case the CAT USB port is the COM19
ELAD FDM-DUO User Manual Rev 1.04 10/2014 © 2014 ELAD S.r.l. All rights reserved. No part of this document may be reproduced, published, used, disclosed or disseminated in any form or by any means, electronic, photocopying or otherwise, without prior written permission of ELAD S.r.l. 64 Run Flash Magic software. In the “Step 1 – Communication” section:  Select LPC1766.  COM Port: the CAT USB com port  Baud Rate: 230400  Interface: None (ISP) In the “Step 2 – Erase” section:  Check “Erase all Flash+Code Rd Prot” In the “Step 3 – Hex File” section:  Click on Browse and select the update “.hex” file In the “Step 4 – Options” section:  Check “Verify after programming Check the communication with the FDM-DUO. Click on ISP and click on “Read Device Signatures”. If the communication with the FDM-DUO is ok, a new windows with some device information is opened. If the communication is Ok, click on close and in the Flash Magic main window, click on Start to begin the programming. Wait until the end of the process, then turn off and restart the FDM-DUO.
ELAD FDM-DUO User Manual Rev 1.04 10/2014 © 2014 ELAD S.r.l. All rights reserved. No part of this document may be reproduced, published, used, disclosed or disseminated in any form or by any means, electronic, photocopying or otherwise, without prior written permission of ELAD S.r.l. 65 9.2 RX demodulator and TX modulator firmware update To update the RX demodulator and TX modulator firmware, you must remove the FDM-DUO top cover. Remove the four screws in the FDM-DUO chassis bottom as shown in the figure below. Then remove the top cover of the FDM-DUO
ELAD FDM-DUO User Manual Rev 1.04 10/2014 © 2014 ELAD S.r.l. All rights reserved. No part of this document may be reproduced, published, used, disclosed or disseminated in any form or by any means, electronic, photocopying or otherwise, without prior written permission of ELAD S.r.l. 66 9.2.1 RX demodulator firmware update Download the latest version of the RX demodulator firmware. Replace the file fdmduorx.bin in the USB pen provided with the FDM-DUO Connect the provided USB pen to the FDM-DUO RX Micro-USB programming port using the provided micro-USB adapter. Connect the power supply, keep pressed the Rx program mode button and power up the FDM-DUO.  Keep pressed the Rx program mode button until the red led turns on.  Release the Rx program mode button .  Wait until the red led turns off.  Turn off the FDM-DUO, disconnect the USB pen and restart the FDM-DUO. If during the firmware update the green leds are blinking quickly, it means that the programming process is failed. In this case contact the technical assistance.
ELAD FDM-DUO User Manual Rev 1.04 10/2014 © 2014 ELAD S.r.l. All rights reserved. No part of this document may be reproduced, published, used, disclosed or disseminated in any form or by any means, electronic, photocopying or otherwise, without prior written permission of ELAD S.r.l. 67 9.2.2 TX modulator firmware update Download the latest version of the TX modulator firmware. Replace the file fdmduotx.bin in the USB pen provided with the FDM-DUO. Connect the provided USB pen to the FDM-DUO TX Micro-USB programming port using the provided micro-USB. Connect the power supply, keep pressed the TX program mode button and power up the FDM-DUO.  Keep pressed the TX program mode button until the red led turns on.  Release the TX program mode button.  Wait until the red led turns off.  Turn off the FDM-DUO, disconnect the USB pen and restart the FDM-DUO. If during the firmware update the green leds are blinking quickly, it means that the programming process is failed. In this case contact the technical assistance.
ELAD FDM-DUO User Manual Rev 1.04 10/2014 © 2014 ELAD S.r.l. All rights reserved. No part of this document may be reproduced, published, used, disclosed or disseminated in any form or by any means, electronic, photocopying or otherwise, without prior written permission of ELAD S.r.l. 68 9.3 USB interface firmware update Download the latest version of the USB interface Turn on the FDM-DUO and connect the USB Receiver data connector port to a USB 2.0 port of your PC. Disable any antivirus program before start the firmware update Run the downloaded file and wait until the end of the update process without disconnecting the USB cable or power off the FDM-DUO, then turn off and restart the FDM-DUO. 9.4 FPGA DDC update Download the latest version of the FPGA DDC. Turn on the FDM-DUO and connect the USB Receiver data connector port to a USB 2.0 port of your PC. Disable any antivirus program before start the firmware update Run the downloaded file and wait until the end of the update process without disconnecting the USB cable or power off the FDM-DUO, then turn off and restart the FDM-DUO.
ELAD FDM-DUO User Manual Rev 1.04 10/2014 © 2014 ELAD S.r.l. All rights reserved. No part of this document may be reproduced, published, used, disclosed or disseminated in any form or by any means, electronic, photocopying or otherwise, without prior written permission of ELAD S.r.l. 69 Declaration of Conformity (EC) The product marked as FDM-DUO manufactured by Manufacturer: ELAD S.r.l. Address: Via Col De Rust, 11 - Sarone 33070 CANEVA (PN) is produced in conformity to the requirements contained in the following EC directives:  R&TTE Directive 1999/5/CE  EMC Directive 2004/108/CE  Low Voltage Directive 2006/95/CE The product conforms to the following Product Specifications: Emissions & Immunity: ETSI EN 301 489-1 V1.9.2 ETSI EN 301 489-15 V1.2.1 ETSI EN 301 783-2 V1.2.1 Safety: EN 60950-1:2006 + A11:2009 + A1:2010 + A12:2011 + A2:2013 And further amendments. This declaration is under responsibility of the manufacturer: ELAD S.r.l. Via Col De Rust, 11 - Sarone 33070 CANEVA (PN) Issued by: Name: Franco Milan Function: President of ELAD Caneva Place July, 30th 2014 Date Signature
ELAD FDM-DUO User Manual Rev 1.04 10/2014 © 2014 ELAD S.r.l. All rights reserved. No part of this document may be reproduced, published, used, disclosed or disseminated in any form or by any means, electronic, photocopying or otherwise, without prior written permission of ELAD S.r.l. 70 Declaration of Conformity (FCC) The product marked as FDM-DUO manufactured by Manufacturer: ELAD S.r.l. Address: Via Col De Rust, 11 - Sarone 33070 CANEVA (PN) complies with the following requirements: - FCC (Federal Communications Commission) Part 15 Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:  Reorient or relocate the receiving antenna.  Increase the separation between the equipment and receiver.  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  Consult the dealer or an experienced radio/TV technician for help. Changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC ID: 2AAE5FDM-DUO This product is distributed in USA by: ELAD USA Inc. 7074 N RIDGE BLVD APT 3E CHICAGO , IL 606453586 USA Pho: 312-320-8160

Navigation menu