Dream Technology DT100 Bluetooth Headset User Manual

Dream Technology Co., Ltd. Bluetooth Headset

User Manual

DT100 User ManualPackage ContentsFeatures
ChargingPower On / OffPairing / ReconnectionThis headset has its own battery inside. The internal batteryMust be fully charged before first time use.72 hours3 hours2 hoursStandby TimeTalk TimeCharging Time-. Charging in progress : Red light on-. Charging completed : Blue light onPress and hold down Power/Call ButtonUntil Red light flashes 3 times.(Approx. 3 seconds)OffPress and hold down Power/Call Button until Blue light flashes 4 times.(Approx. 3 seconds)OninstructionFunctionPairingPair the headset with the mobile phone before using the device. Pairing is a process which establishes a new relationship between two Bluetooth enabled devices through the exchange of a link key.ⒶMake sure that the headset is turned off.ⒷSet the headset to a pairable state.Press and hold down for 5 seconds until blue light isturned on.ⒸSearch for the headset on your mobile phone according to the guide of the phone. In most cases, selecting ¡set¡and ¡connection¡ from the menu to search for the bluetoothdevice. You may also select the option to add the device directly.ⒹWhen the mobile phone finds DT100, pair it with the phone.ⒺIn case the mobile phone asks for passkey or PIN, enter0000 to connect the two devices.ReconnectionReconnection is needed when you are out of range and thenCome back into range or when the headset is powered on again.Tap the Power/Call Button once.
SpecificationsFunctionsMake a Call-. Last number RedialingTapping the Power/Call Button once displays the list andTap the Power/Call Button to make a callNotes) For some mobile phones, calls can be directly made displaying the list.-. Voice DialTapping the Power/Call Button once and say the person¡sname.Notes) Voice dial can be used only if the mobile phone has voice recognition feature and the headset is registered under handsfree service.Please see the user guide of your phone for detail.End a Call-. Tap the Power/Call Button once.Accept a Call-. Tap the Power/Call Button once after the tone (incoming)Reject a Call-. Press and hold down the Power/Call Button for 1 second.Notes) The reject call function can be used only if the mobile photo has a rejectcall feature. The headset must be registered under a handsfree serviceAdjust volume-. Tap the volume Button (▲or ▼) to adjust volume accordingly.Microphone Mute-. Press the volume Button (▲or ▼) for 1 second during a call.Cancellation is same.Call Transfer-. Tap the Power/Call Button once.Notes) you can switch to the headset only once when you receive a call from the mobile phone.Call waiting-. Press the Power/Call Button for 1 second when anothercall arrives during a call.Notes) The function can be used only if the service provides the call waitingfunction. The headset must be registered under the handsfree service. Please see the user guide for detail.10gWeight65.7(L) X 18 (W) X 16 (H)Dimensions (mm)Up to 72 hoursStandby TimeUp to 3 hoursTalk TimeUp to 10m (33 feet)Operating RangeVersion 2.0 (Class 2)Bluetooth Version
<<NOTICE>> * Section 15.19 Labelling requirements This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference and (2) This device must accept any interference received, (3) including interference that may cause undesired operation. * Section 15.21 Information to user The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, no change to the antenna or the device is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure requirements and void user’s authority to operate the device.

Navigation menu