Doodle Labs NM-2450-2F Wi-Fi Radio Transceiver User Manual Users manual

Doodle Labs (SG) Pte Ltd Wi-Fi Radio Transceiver Users manual

Users manual

NM-2450-2FRugged/Military grade 2.4 GHz 2x2 MIMO Wi-Fi® Radio TransceiversFeaturesQualcomm-Atheros AR9590-AR1B Chipset with Extended Temperature RangeUp to 300 Mbps Throughput with 2x2 MIMO TechnologyCalibrated High Power 2.4 GHz (27 dBm) and 5 GHz operation (25 dBm) for Extended Range802.11 Dynamic Frequency Selection (DFS) in AP and Client mode Supported Ath9k Linux DriverMiniPCIE InterfaceUser Manual
TECHNICAL SPECIFICATIONSModel No. NM-2450-2F (802.11n, ath9k driver)MAC Chipset11n Models – Qualcomm AtherosQCA9590-AR1B with Extended Temperature range for Outdoor and Rugged models)Software Support Linux Driverath9kCenter Frequency Range 2.412 GHz ~ 2.484 GHzThis varies by the regulatory domainChannel Bandwidth* 20, and 40 MHz channelsRadio Modulation (Auto Adjust) CCK, BPSK, QPSK, 16 QAM, and 64 QAM (2.4 GHz – 11n models)Data Rates Supported 802.11n: MCS0-23802.11b/g: 1, 2, 5.5, 6, 9, 11, 12, 18, 24, 36, 48 and 54 Mbps (2.4 GHz)802.11n version 2.0 Capabilities802.11n and b/g Beam FormingPacket aggregation: A-MPDU (Tx/Rx), A-MSDU (Tx/Rx), Maximal ratio combining (MRC), Cyclic shift diversity (CSD), Frame aggregation, block ACK, 802.11e compatible bursting, Spatial multiplexing, cyclic-delay diversity (CDD), low-density parity check (LDPC), Space Time Block Code (STBC)Operating Modes AP, STA and Adhoc modes to implement Point to Point, Point to multi PointMAC Protocol TDD with Carrier Sense Multiple Access with Collision Avoidance (CSMA/CA)Wireless Error Correction FEC, ARQWireless Data Security 128 bit AES, WEP, TKIP and WAPI hardware encryption. Support for IEEE 802.11d, e, h, i, k, r, v, w and time stamp standardsFIPS Certification Loop back mode to facilitate FIPS AES certification, Small packet size (96 bytes) in AES encryption at full packet rateTx/Rx Specification RadioModulationCodingRateMax Tx Power(± 2 dB)Rx Sensitivity(Typ)20 MHz Channel – 11n models802.11b, STBC CCK 1/2 28 -100802.11b, STBC 64 QAM 3/4 26 -80MIMO BPSK 1/2 28 -92MIMO 16 QAM 3/4 28 -82MIMO 64 QAM 5/6 26 -7240 MHz Channel – 11n modelsMIMO BPSK 1/2 28 -90MIMO 16 QAM 3/4 28 -79MIMO 64 QAM 5/6 26 -70* It is advantageous to use the smallest Channel Bandwidth that can support the Throughput requirements. Smaller bandwidths provide more channels to choose and help avoid interference issues. The system’s SNR is higher at smaller Channel Bandwidths and Range is longer.Antenna Signal Strength -35 dBm to -85 dBm (Recommended), (Absolute Maximum=+12 dBm)Antenna port isolation for concurrent operation+10 dBm signal strength for 5 GHz signal without degrading 2.4 GHz operationIntegrated Antenna >20 KV (Human Body Model)
Port ProtectionReceiver LNA Gain +10 dBReceiver Adjacent Channel Rejection (ACR)>38 dB @ 11g, 6 Mbps (Typ)Receiver Alternate Channel Rejection (ALCR)>42 dB @ 11g, 6 Mbps (Typ)Receive chain Noise Figure +6 dBTransmitter Adjacent Channel Leakage power Ratio (ACLR)45 dB (Fc ± ChBW)Transmitter Spurious Emission Suppression-40 dBcRF Hardware Disable (RF Kill) Pin 20 of miniPCI-E interface. (Required for FAA compliance)Control for ExternalPower Amp Available as an optional configurationRF Power control In 0.5 dBm steps. Accuracy of power calibration loop ±2 dBm. Each transceiver individually calibrated and tested.PHYSICAL, ENVIRONMENTAL AND OTHER SPECIFICATIONSAntenna Ports 2 MMCX Ports (50 Ohms)Host CPU Board Any CPU board with Industry standard miniPCI-Express interface with minimum 6 mm connector heightOperating Voltage3.3 Volts from miniPCI-E interface for radio3~4.5V for FES. Optional DC-DC converter available for 6V~38V power input. Power ConsumptionTotal 16W (14W @ Max power for FES, in data transfer mode on all chains + 2Wfor radio module)Total 10W (8W @ 20 dBm power for FES in continuous data transfer mode on allchains + 2W for radio module)1.2W total power in continuous data receive modeShield case temperature range (Operating)-40°C to +80°CThe System’s thermal design should ensure that the transceiver’s shield case temperature is maintained within these specifications.Prism-FES can be mounted away from the host CPU board for better thermal designCable Assembly Includes the harness with RF cable and DC power for Prism-FESHumidity (Operating) 0% – 95% (Non-condensing)Dimensions1x 30 x 50 x 6 mm Radio module, 2x 30 x 52 x 7 mm FES modules, 14 + 2×23 = 60 gramsMechanical drawing and 3D-CAD files available upon requestRegulatory RequirementsDesigned and Verified to meet various regulatory requirements. Formal testing and approval is required based on the Integrator’s particular host platform. The Integrator is also responsible for obtaining any other
required regulatory approvals in target markets for the finished product.Doodle Labs can offer assistance for compliance testing of the System Integrator’s host platform.FCC ID Q3 2016CE Certification Q3 2016IC Certification Q3 2016RoHS/WEEE Compliance Yes. 100% Recyclable/Biodegradable packaging
FCC StatementChanges or modifications not expressly approved by the party responsible for compliance could void the user's authority tooperate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCCRules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. Thisequipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with theinstructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will notoccur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can bedetermined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of thefollowing measures:-- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for helpThis device complies with part 15 of the FCC rules. Operation is subject to the following two conditions (1)this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operationSingapore: USA:Doodle Labs (SG) Pte. Ltd. Doodle Labs LLC150 Kampong Ampat 2 Mattawang DriveKA Center, Suite 05-03 Somerset, NJ 08873Singapore 368324 Tel: +1 862 345 6781Tel: +65 6253 0100 Fax: +65 6353 5564 The antenna(s) used for this transmitter must be installed to provide aseparation distance of at least 20 cm from all persons and must not becollocated or operating in conjunction with any other antenna or transmitter,except in accordance with FCC multi-transmitter product procedures.Radiation Exposure Statement:This equipment complies with FCC radiation exposure limits set forth for anuncontrolled environment.This transmitter must not be co-located or operating in conjunction with any otherantenna or transmitter.The availability of some specific channels and/or operational frequency bandsare country dependent and are firmware programmed at the factory to matchthe intended destination.The firmware setting is not accessible by the end user.The final end product must be labelled in a visible area with the following:“Contains Transmitter Module 2AG87NM-2450-2F”In the event that these conditions can not be met (for example certain laptop configurationsor co-location with another transmitter), then the FCC authorization is no longer consideredvalid and the FCC ID can not be used on the final product. In these circumstances, the OEMintegrator will be responsible for re-evaluating the end product (including the transmitter) andobtaining a separate FCC authorizationet (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptibleLe présent appareil est conforme aux CNR d'Industrie Canada applicable aux appareils radio exempts de licence.The term "IC: " before the certification/registration number only signifies that the Industry Canada technical specifications were met. (1) This device may not cause interference; and This device complies with Industry Canada's licence-exempt RSSs. Operation is subject to the following two conditions: (2) This device must accept any interference, including interference that may cause undesired operation of the device. This product meets the applicable Industry Canada technical specifications.L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage,d'en compromettre le fonctionnementIC StatementThe modular can be installed or integrated in mobile or fix devices only. This modular cannot be installed in any portable device, for example,USB dongle like transmitters is forbidden.The module could be only used as a system and integrated as a system and compliance withthe Section 15.204(b) rule part.

Navigation menu