Detector Electronics 2WTC2 Remote Keyless Entry System User Manual OP92WTC2

Detector Electronics Company Remote Keyless Entry System OP92WTC2

Users Manual

1. What is includedIndicating Transmitting & ReceivingTo enter a mute modeTo exit a mute modeVibrate modeThe automatic door open cancellationIndicating the siren onIndicating the siren offBattery level indicator(Full)Battery level indicator(Replace)Indicating the system is armingIndicating the system is disarmingIndicating a pagingIndicating the shock sensor has been triggeredIndicating the timer modeIndicating an alarm mode This device complies with part 15 of the FCC rules. Operation is subject to the following twoconditions: (1) This device may not cause harmful interference, and (2) This device must acceptany interference received, including interference that may cause undesired operation.Caution : Any changes or modifications in of this device which are not expressly approved bythe party responsible for compliance could void the user's authority to operate the equipment2. Standard Icon configuration of Remote1. MAIN UNITS 2. ACC. PARTS1. Control Module 2. LCD 2Way Remote 1. 6-Tone Siren 2. Paging Sensor3.rx 2Way Antenna 3. Shock Sensor 4. Wiring Harness
Disarm Unlock My car numberCalling Shock detectedTrunk released Vibrate enableSiren set up Arm lock Button Press Time Sound DescriptionArm / DisarmDoor Lock / Unlock3sec Panic ModeⅡ1sec Beep To start & stop the EngineⅢ3sec Beep Trunk Release2sec Beep To confirm the status of the systemManner option(Beep mode/Silent mode/Vibrate mode)Aux 2sec Beep To find my car3sec Beep To set the clock of Remote4sec Beep Beep To set the alarm clock of remote5sec Beep Beep Beep To set of remote control6sec Beep Beep Beep Beep The car number inputTo engage & disengage the silent modeof the systemTo engage & disengage the valet modeof the systemTo engage & disengage the mode ofLPG engine3. Diagram of using TransmitterⅠ1sec BeepCheck keep going Beep BeepⅡ+ⅢCheck + Aux3sec Beep4sec Beep Beep5sec Beep Beep Beep
1. REMOTE CODE LEARNING2. To enter programming mode3. Disarming without a transmitter
4. Warning
 ο MAKER : KUM YOUNG  ο PCB AND HELICAL ANTENNA SOLDERING CONNECTION 5 MODEL AND MANUFAVTURER OF ANTENNA  ο MODEL NAME : HELICAL ANTENNA  ο MODEL NO : RF-17  ο INTENTION QUALITY : OMNIDIRECTIONAL 3 PARTIAL QUALITY OF ANTENNA  THERE IS NOT CORRESPONDENCE 4 CONNECTION FROM OF TRANSMISSION SYSTEM 1 TYPE AND FORM OF ANTENNA  ο HELICAL ANTENNA 2 GAIN AND INTENTION QUALITY OF ANTENNA  ο GAIN : 1.5dBi ANTENNA SPECIFICATIONRECEPTION : DETECTOR Electronics Co., LtdCONSULTATION :SUBJECT : ANTENNA SPECIFICATIONFILE NO : 200602-01ISSUE DATE : 2006. 02. 15
1) ANTENNA PATTERN
OFF ON11223344556677E/1Paging Sensor/LEDE/2E/3D/1AntennaD/2D/3D/4D/5C/1 Shock SensorC/2 DIP SWITCHC/3B/7 BLACK/WHITE (+)Generator InputB/8 EmptyB/5 EmptyB/6 PINK (+)Parking Light InputB/3 BLUE (+)Light Flash OutputB/4 BROWN/WHITE (+)Siren OutputB/1 ORANGE (-)Door Trigger InputB/2 BLUE (+)Light Flash OutputA/5 PURPLE (-)400mA Optional Channel OutputA/6 RED (+)400mA Optional Channel OutputA/3 GREEN (-)400mA Lock OutputA/4 YELLOW (-)400mA Unlock OutputA/1 RED (+)10A Lock OutputA/2 BLACK (+)10A Unlock OutputM/5 YELLOW (+)Output to Starter CircuitM/6 BLUE (+)Output to Ignition CircuitM/3 WHITE (+)Output to Second Ignition CircuitM/4 RED (+)Constant 12V InputTEC - 2WAY COLOR INSTALLATION GUIDEM/1 ORANGE (-)400mA Starter Kill/Option #1/Option #2M/2 BLACK (-)Chassis Ground Input
OFFONOFFONOFFONOFFONOFFONOFFONOFFONFOR SAFETY,DO NOT INSTALL THE REMOTE ENGINE START SYSTEMTHE VEHICLE WITH GEAR SHIFT TRANSMISSION.WARNING!6Starter Output shut down(Power Noise)Starter Output shut down(Generator input)7The Vehicle with Vacuum ValveFor LPG Engine4Programming Crank Time(0.8 seconds)Programming Crank Time(1.5 seconds)5Programming Reservation Type A for next Remote Engine StartProgramming Reservation Type B for next Remote Engine Start2For vehicle with LPG engineFor vehicle with automatic transmission3Programming pre-ignition output time(4 or 6 seconds)Programming Pre-ignition output time(8 or 12 seconds)DIP SWITCH1Starter Relay Turn-onLPG or Vacuum valve
1. (-)400mA Output when arm the system(For Starter Relay Turn-on) 2. (-)400mA Output when remote engine starts.(To open the vacuum valve) 3. (-)400mA output when closing the door after program the remote engine start reservation. (To burn the rest LPG gas in the engine in winter time)(-)Chassis Ground Connection Connect this wire to a clean, paint-free sheet metal location(driver kick panel) using a factory bolt that DOES NOT have any vehicle component grounds attached to it. A screw should only be used when in conjunction with a two-sided lock washer. Under dash brackets and door sheet metal are not acceptable ground points. It is recommended that all security components be grounded at the same location.Output to Second Ignition Circuit. Connect this wire to the second ignition wire in the vehicle. NOTE: For vehicle that do not have a second ignition wire, this connection is not required.(+)12V input Remove the two 30 amp fuses prior to connecting these wires and do not replace them until the satellite has been plugged into the control module. These wires are the source of current for all the circuits the relay satellite will energize. They must be connected to a high current source. Since the factory supplies (+) 12V to the key switch that is used to operate the motor, it is recommended that these wires be connected there.Starter Output Connect this wire to the starter wire in the vehicle.Ignition Output Connect this wire to the ignition wire in the vehicle.M/6 BLUE M/2 BLACK M/3 WHITE M/4 RED M/5 YELLOW M/6 BLUE (+)Output to Ignition Circuit ■ Wire DescriptionM/1 ORANGE M/4 RED (+)Constant 12V InputM/5 YELLOW (+)Output to Starter CircuitM/2 BLACK (-)Chassis Ground InputM/3 WHITE (+)Output to Second Ignition CircuitIgnition/Start/Power Wire Connection Guide ■ Wiring DiagramM/1 ORANGE (-)400mA Starter Kill/Option #1/Option #2
Direct Output to Lock Wire of Door Lock Servo Motor Direct Output to Unlock Wire of Door Lock Servo Motor Output to Door Lock Wire Output to Door Unlock Wire (-)400mA Output (+)400mA OutputWhen the system receives the code controlling Channel 2, the PURPLE wire will supplyan output for one second. This is often used to operate a trunk release or other relaydriven function.A/6 RED A/2 BLACK A/3 GREEN A/4 YELLOW A/5 PURPLE A/6 RED (+)400mA Optional Channel Output■ Wire DescriptionA/1 RED A/4 YELLOW (-)400mA Unlock OutputA/5 PURPLE (-)400mA Optional Channel OutputA/2 BLACK (+)10A Unlock OutputA/3 GREEN (-)400mA Lock OutputDoor Lock/Optional Output Harness■ Wiring DiagramA/1 RED (+)10A Lock Output
(-)Door Trigger InputMost Vehicles use negative door trigger circuits. Connect the ORANGE wire to a wireshowing ground when door is opened. (+)Light Flash OutputConnect this wire to (+)parking Light Wire of the vehicle.When you connect to the signal light, connect these wires to the signal light wires. (+)Siren OutputConnect this to the brown/white wire of siren. Connect the black wire of the siren to (-)chassis ground. (+)Parking Light InputThis is used to warn a driver that the lights of the vehicle on when arm the system.Connect this wire to (+)parking light wire. (+)Generator InputThis input provides the control module when the engine of the vehicle starts to run.Connect this wire to generator or oil lamp wire showing (+)power when engine starts to run.B/7 B/W B/2, B/3BLUE B/4 B/WB/6 PINK B/8 Empty■ Wire DescriptionB/1 Orange B/6 PINK (+)Parking Light InputB/7 BLACK/WHITE (+)Generator InputB/4 BROWN/WHITE (+)Siren OutputB/5 EmptyB/2 BLUE (+)Light Flash OutputB/3 BLUE (+)Light Flash OutputPrimary harness Wire Connection Guide■ Wiring DiagramB/1 ORANGE (-)Door Trigger Input
: (-)White InputInput will trigger full alarm sequence and siren will sound for 10 seconds.Receiver/Antenna position should be discussed with the vehicle owner prior toinstallation, since the antenna may be visible to the vehicle's owner.The best location receiver/antenna is high on front wind shield.For optimal range, the antenna should be mounted horizontally.Metallic window tint can also affect range, so this should be a considerationwhen determining the mounting location.After determining the best mounting location, follow these steps;1. Clean the mounting area with a glass cleaner to remove any dirt or residue.2. Mount the receiver/antenna using the supplied double sided tape.3. Route the receiver/antenna cable to the control module and plug into the five-pin antenna connector.Antenna 5 Pin White PlugD/1AntennaD/2D/3D/4D/5Peripheral Plug-In harnessShock Sensor 3 Pin White PlugC/1 Shock SensorC/2C/3
This sensor is used to page a absent driver and has LED circuit inside.Paging sensor/LED position should be discussed with the vehicle owner prior toinstallation.The best location sensor/LED is left side bottom of front windshield.After determining the best mounting location, follow these steps;1). Put sensor on guide sticker using the supplied double-side tape.2). Put guide sticker on front windshield.3). Route the sensor cable to the control module and plug into the 3-pin paging sensor/LED connector.Paging Sensor/LED 3 Pin Yellow PlugE/1Paging Sensor/LEDE/2E/3
These dip switches are used to determine and program the various functions (ex: output time etc.)of control module. 1. OFF : 400mA Armed OutputThis dip switch is used to determine the M/1 output.The M/1 output wire will supply a (-)400mA ground as long as system is armed.And this output ceases as soon as the system disarmed.No.1/ON & No.7 OFF :400mA Output when you start the engine by remote.These dip switches are used to determine the M/1 output.This M/1 output wire will supply a (-)400mA ground as long as system runs engineto open the vacuum valve of the vehicle.And this output ceases as soon as the system stopped the engine running.No.1/OFF & No.7 ON & No.2 OFF :400mA Output for LPG engine.These dip switches are used to determine the M/1 output and remote start reservationfor the vehicle with gear shift transmission.At winter time, most of the vehicle with LPG engine needs to burn the rest of LPGgas in the engine.If the system was programmed as the above, the system will supply the ignitionoutput to continue the engine running even a driver turned off the engine with key.After exit and close all doors of the vehicle, M/1 output will supply (-)400mA groundto operate an optional really for LPG vehicle.And this output ceases as soon as the input stopped from the generator wire ofthe vehicle.1. OFF : To operate LPG Wire.This dip switch is used to determine the operating mode of M/1 output.The system will supply the ignition output when a driver turned off the engine withkey to continue the engine running.And this output ceases as soon as the door is locked.2. ON : Remote engine start1. OFF : To Program the Ignition Output Time(4 or 6 Seconds)This function is used for the gasoline engine vehicle.2. ON : To Program the Ignition Output Time(8 or 12 Seconds)This function is used for the diesel engine vehicle.No.2 Dip SwitchNo.3 Dip SwitchProgramming DIP SWITCHNo.1 Dip SwitchNo.1&7 Dip SwitchesNo.1,7 & 2 Dip Switches
1. OFF : To Program the Crank Time(0.8 seconds)This function is used to determine crank time shortly for the new car.2. ON : To Program the Crank Time(1.5 seconds)This function is used to determine crank time longer for the used car.1. OFF : Starter output shut down(Power Noise)This function is used to determine the mode of crank shut down.The system will stop the start output when the system detects the power noiseof the vehicle after engine running.1. ON : Starter output shut down(Generator Input)This function is used to determine the mode of crank shut down.The system will stop the start output when the system detects the generator wireinput of the vehicle after engine running.No.4 Dip SwitchNo.6 Dip Switch
◈ MODEL : TEC-2WAY COLOR◈ Genuine Accessories of Hyundai MOBIS ◈ ISO - 9001 registered mobile electronic productsFeatures♦ 5 button 2-way remote start / security / Keyless entry system♦ 65,000 color LCD♦ Super high Frequency♦ System's status check Via LCD display♦ Remote Engine Start♦ Find Location♦ Programmable running time ( 15, 25 minutes )♦ Arm / Disarm by remote♦ Arm in mute & Valet mode by remote♦ Door lock & unlock by remote♦ Parking light flash♦ Door & Shock Detect♦ Power Trunk Release♦ Paging sensorRemote Control diagram① button - Door Lock / Unlock② button - To start & stop the Engine③ button - Trunk ReleaseCheck button - To confirm the status of the systemAux button - Find the my carVehicle Security System

Navigation menu