Datto DNWAP62 WiFi Access Point User Manual AP62

Datto, Inc. WiFi Access Point AP62

User Manual-AP62

For more information, visit www.datto.com/networking © 2017 Datto Inc. All rights reserved.Outdoor MountThis access point can be congured as an outdoor model andmounted to any wall or pole. This conguration protects againstthe sun, rain and dust. Operating temperatures for this accesspoint range from 0°C to 50°C. (Outdoor for NII-3)Ethernet or Junction Box MountThis access point can be mounted to any junction box for secure installations in hotel and resort guest rooms, dorms, care facilities and more. AP62Quick Start GuideAdditional ResourcesDatto’s Partner Portal (partners.datto.com) is the place to go for everything Datto. The Partner Portal includes:• Datto Knowledge Base (kb.datto.com) - technical articles to help you with all of your Datto Networking needs • MarketNow (datto.com/marketnow) - your very own Marketing Automation Platform • Sales Resources - Sales Playbooks, MSPeasy eBooks and videos, etc. Your dedicated Channel Account Manager can help with sales and planning questions along the way. If you need additional help, the Datto Support Team is here for you 24/7/365. Contact Ussupport@datto.comNorth America: +1.877.455.6015EMEA: +44.(0).118.402.9609 Australia/New Zealand: +61 (02) 8015 68261) Remove rear door and seal. 2) Mount at side of plate to junction box.4) Slide device down plate to lock in place.3) Connect included slim ethernet cable from device (Port 1) to connection in wall.1) Remove rear door and seal. Peel plastic tab off from door.2) Secure at side of mount to outdoor xture. Arrows on plate pointing upwards.3) Place ethernet cable through seal and connect to device (Port 1). Reinstall seal and back cover.4) Slide device down plate to lock in place.Unmounting DirectionsTo unlock, insert a small, at screwdriver into the Mount Release Hole on the side of the access point. Slide the access point upwards until it disengages from the mounting plate.
Mounting Bracket OverviewT-Rail Ceiling MountFor attaching to drop ceiling T-Rail or other T-Rail System.LED indicatorEthernet Port1, 802.3af PoE(48-54V=0.6A)Reset Button Cable ChannelUSB 2.0Ethernet Por2, passive PoE(18-24V=1.34-1A)Physical InstallationThis access point is designed to be installed indoors or out, in several mounting positions. Regardless of how you mount this access point, keep the following in mind:• 802.3af PoE input is required. Connect to any Datto Networking Switch, an 802.3af-compatible PoE switch or PoE injector.• Place in the center of the room and away from any metallic surfaces.• Signal primarily radiates to the front and sides. There is limited signal coverage directly behind it. • Do not place heavy objects on the access point.• Install in an area free from strong electromagnetic sources.• Check the Ethernet cables to ensure they are fully secured to both the access point and PoE injector or switch.• Do not install this access point in plenum spaces. Use the ceiling mount instead. US singlegang boxUS dualgang box Wall or Solid Ceiling MountAttach the universal mounting plate to any solid surface (screws are not included). STATE LIGHT COLOROnline, Mesh Speed >2Mbps Solid BlueOnline, Mesh Speed <=2Mbps Flash BlueBoot Loader Solid PurpleBooting Up Solid YellowFirmware Upgrade Solid RedCloudTrax Checkin Failure Flash WhiteKey Re-pair Flash YellowConguration Change AP not ready Solid WhiteNet Failure - no default route Flash RedAccess Point OverviewLED Light States1) Remove rear door and seal. 2) Mount at side of plate to wall or ceiling. 3) Connect ethernet cable to device (Port 1). 4) Slide device down plate to lock in place.2) Place all four T-Rail clips into mounting plate. 3) Place ethernet through mount and connect ethernet to device (Port 1). Slide mount onto device.4) Use the adjustable rail clips to tighten to the ceiling T-Rail until secure.What’s in the Box(1) Access Point(4) T-Rail Clips (ceiling rail mount)(1) Slim Ethernet Cable (for wall or junction box mount)(1) Mounting Plate(1) Ethernet Hole CoverCloud Management1. Sign in to networking.datto.com. Click Add New button. 2. Create a new network by navigating to All Networks > Create Network, or select an existing network on the All Networks page. 3. On the left menu, navigate to Access Points. Click Add New and enter the MAC address. Use the drop-down arrow to enter multiple MAC addresses at once or upload a CSV file. Repeat this process to add as many access points as required. 4. Connect device to internet over ethernet or an existing Datto mesh network. The device will then configure and start reporting status within a few minutes.Note: Ethernet port 1 is PoE input. The pass-through port (Ethernet 2) is data only. No power is passed through the second port.Smaller, Adjustable T-RailLarger, Fixed T-RailAccess PointSlim Ethernet CableEthernet Hole CoverMounting PlateEthernet port 1, 802.3af PoE1) Remove rear door and seal. 1) Remove rear door and seal. 15/16" rails 9/16" railsSmaller, Adjustable T-RailLarger, Fixed T-RailT-Rail (not included)Ethernet port 1, 802.3af PoE

Navigation menu