D Link WM800BA1 DC-HSPA+ module User Manual DWM 800B Hardware User Guide

D Link Corporation DC-HSPA+ module DWM 800B Hardware User Guide

user guide DWM-final.pdf

DWM-800B HW User Guide
2 CONTENT 1. INTRODUCTION ............................................................................................................................................... 3 1.1. OVERVIEW ............................................................................................................................................................................3 1.2. APPLICATION TYPE ...............................................................................................................................................................3 1.3. INSTALLATION GUIDELINES .................................................................................................................................................4 1.4. APPLICATION SCENARIO .......................................................................................................................................................4 2. DWM-800B INTERFACES ........................................................................................................................... 5 2.1. DWM-800B INTERFACE SUMMARY.....................................................................................................................................5 2.1.1. RF interface ...............................................................................................................................................................5 2.2. APPLICATION NOTE OF DWM-800B INTERFACES ..............................................................................................................7 2.2.1. Power supply and Ground ............................................................................................................................................7 2.2.2. USB interface ...............................................................................................................................................................8 2.2.2.1. Description ...................................................................................................................................................................8 2.2.3. USIM interface ............................................................................................................................................................9 2.2.4. PCM interface ...........................................................................................................................................................10 2.2.5. SD card tntreface .......................................................................................................................................................11 2.2.6. Others .........................................................................................................................................................................11 3. ELECTRICAL CHARACTERISTICS AND SAFETY INFORMATION ..................................................... 12 3.1. ABSOLUTE MAXIMUM RATINGS .........................................................................................................................................12 3.2. POWER-UP AND POWER-DOWN SEQUENCE .......................................................................................................................12 3.3. OPERATING CONDITIONS ...................................................................................................................................................13 3.4. RF EXPOSURE COMPLIANCE .............................................................................................................................................14 4. PINS DESCRIPTION OF MINI PCIE CONNECTOR ................................................................................. 15 FEDERAL COMMUNICATION COMMISSION INTERFERENCE STATEMENT ......................................... 16
3 1. Introduction 1.1. Overview The DC-HSPA+ Mini PCIe module DWM-800B , powered by MT6280 chipset, can be integrated into any devices for 3G mobile applications. It provides SMS, MMS, Call as well as high speed internet access to DC-HSPA+and UMTS networks worldwide. Main features of DWM-800B is listed in table 1-1 Table 1-1 Main Features of DWM-800B Item Description Air Interface DC-HSPA+/UMTS/EDGE/GPRS/GSM/WCDMA Transmit speed DL 42 Mbps, UL 11 Mbps Frequency GSM Band : 850/900/1800/1900MHz UMTS Band: 2100/1900/850 MHz Operating temperature range Normal Operation: 0°C to +45°C Storage: -20°C to +65°C Size 51mm*30mm*4.7mm Voltage range Power Supply: 3.3V-3.6V 1.2. Application Type The application type of the module is shown as bellow: All instructions relating to the integration of the module described on the FCC Grant notes must be followed.
4 1.3. Installation Guidelines Careful planning and preparation of any installation will always benefit the end result, always read and follow all installation instructions. Follow ESD precautions and prepare an SD safe workspace for installation. Turn the power to the host off and ground yourself to dissipate static charge. Mount only in sockets and locations intended for Mini PCIe cards consult manufacturer on thermal management recommendations for the module mounted within the host. 1.4. Application scenario The HSPA module DWM-800B supports Voice Call, SMS, MMS and internet access functions. The block diagram of DWM-800B is as follows: Figure1-1 DWM-800B block diagram
5 2. DWM-800B interfaces 2.1. DWM-800B interface summary The module DWM-800B supports multimode operation: DC-HSPA+, UMTS (850/1900/2100 MHz) and quad-band GSM (850/900/1800/1900 MHz). The size of DWM-800B is 51mm*30mm*4.7mm. The appearance is shown in Figure 2-1 and Figure 2-2. Figure 2-1 The front view of DWM-800B Figure 2-2 The rear view of DWM-800B The MINI PCI-E is shown as in Figure , which is the main interface for application. RF antenna pad connector is shown as in Figure 2-1 . 2.1.1. RF interface The DWM-800B module provides an interface for RF antenna by Connector: DWM-800B uses HRS’s U.FL-R-SMT RF connector on the rear side. Solder pad mode: The antenna can also be soldered to the pad on the module which has a ground pad close to the antenna pad. The ground impedance of RF antenna is 50Ω. The RF connector is shown in Figure 2-3.
6 Figure 2-3 The sketch map of RF connector It’s required to use RF cable of which the insertion loss should comply with: • GSM850/900<1dB • DCS1800/PCS1900<1.5dB • UMTS2100/ UMTS1900/ UMTS850<1.5Db There are two RF connectors in DWM-800B ,the description of them is shown in Figure 2-4 below:
7 Figure 2-4 description of DWM-800B RF connectors 2.2. Application note of DWM-800B interfaces DWM-800B provides rich interfaces for secondary development by the MINI PCI-E, such as USIM card interface, USB interface, UART interface, PCM（Pulse Code Modulation) interface, I2C interface, power supply interface and so on. The detailed information will be described in the following sections. 2.2.1. Power supply and Ground The power supply input for DWM-800B module is listed as follows: DC +3.3V～+3.6V, for DWM-800B working voltage; The description of DWM-800B Power supply and GND pins is shown in Table 2-1 below. Table 2-1 The description of DWM-800B Power supply and GND pins Power input The correlative pins in MINI PCI-E SN. of the MINI PCI-E DC: +3.3V～+3.6V input VDD3V3 2,24,39,41,52 GND GND 4,9,15,18,21,26,27,29,34,35,37,43,50
8 2.2.2. USB interface 2.2.2.1. Description DWM-800B provides a high-speed USB interface by MINI PCI-E, which supports USB 2.0 protocol. The detailed information is given in Table 2-2. Table 2-2 DWM-800B USB interface description Signals of USB interface The correlative pins in MINI PCI-E SN. of MINI PCI-E Description DM USB_HS_DM 36 USB Data- DP USB_HS_DP 38 USB Data+ GND GND 4,9,15,18,21,26,27,29,34,35,37,43,50 GND 2.2.2.2. Reference circuit The reference circuit of USB interface is shown in Figure 2-5 below. 1) To get the reliable USB power supply, it is recommended to use a 10uF（C406) filter capacitor and a 22pF（C407) filter capacitor which need to be grounded. 2) To reduce the reflection caused by the high frequency alternating signal in the transmission, it is recommended to add a resistor with value below 10Ω to the DM and DP in USB interface to ensure correct transmission for USB data. Just like the resistors R408 and R409 in Figure 2-5. 3) To avoid static electricity in USB interface, it is recommended to use the ESD protection device. Just like the varistor RV406, RV407 and RV408 with capacitor values below 3pF. 4) To ensure USB working reliably, it is recommended to use additional protection device. Figure 2-5 The reference circuit of USB interface
9 2.2.3. USIM interface DWM-800B supports USIM card in UMTS mode as well as SIM card in GSM/GPRS/EDGE mode，and UIM card in WCDMA mode. 2.2.3.1. Description DWM-800B provides USIM card interface by MINI PCI-E which can be used in both UMTS and GSM/GPRS/EDGE networks. The Table 2-3 gives more detailed information. Table 2-3 DWM-800B USIM card interface description Signals offered by USIM interface The name of the correlative pins in MINI PCI-E SN. of the MINI PCI-E Description DATA USIM_DATA 10 USIM card data CLK USIM_CLK 12 USIM card CLK RST USIM_RESET 14 Reset signal VCC VREG_EXTUSIM 8 USIM card power GND GND 4,9,15,18,21,26,27,29,34,35,37,43,50 GND 2.2.3.2. Reference circuit The reference circuit of USIM interface is shown in Figure 2-6 below. 1) The DATA line of USIM is connected to SIM power supply by a pull-up resistor with reference value 15KΩ. 2) To avoid the instantaneous voltage overflowing, the resistor with reference value 22Ω can be used for the DATA, CLK and RST line. Just like the resistors R307, R308 and R309 in Figure 2-6. 3) To avoid the static electricity in USIM socket, it is recommended to use the ESD protection device for the DATA，CLK and VCC line. Just like the varistors RV301, RV302, RV303 and RV304 in Figure 2-6 this should be close to the USIM socket as possible. 4) To get more flat USIM power supply, it is recommended to use the filter capacitors. Just like C311 and C312 in Figure 2-6with reference value 33pF and 100nF. 5) To eliminate the peak interference and high frequency interference signal on RST and CLK line, the filter capacities (C310, C309) can be placed in RST and CLK line, the reference value is 33pF.
10 Figure 2-6 The reference circuit of USIM interface 2.2.4. PCM interface It can just support PCM(Optional). It can provide voice call by PCM ，using external audio codec . DWM-800B provides a UART interface by MINI PCI-E for debug. 2.2.4.1. Description PCM interfaces on the DWM-800B have been designed to be compatible with others so as to meet different needs. And we can make corresponding configuration for interfaces on the DWM-800B according to customer's requirements. The information about UART and PCM interfaces provided by DWM-800B is described in Table 2-4 Table 2-4 The connection between phone handle and the MINI PCI-E SN. of MINI PCI-E Compatible definition 45 PCM_CLK
11 47 PCM_SYNC/PCM_IN 49 PCM_OUT/PCM_IN 51 PCM_IN/PCM_SYNC 2.2.5. SD card tntreface 2.2.5.1. Description There are seven pins for SD card in the MINI PCI-E. And the detailed information is given in Table 2-5 below. Table 2-5 DWM-800B SD card interface description pcie Pin.NO Signal name Description 13 SDC1_CMD SD Command/Response 17 SDC1_DATA0 SD Data 0 19 SDC1_DATA1 SD Data 1 23 SDC1_DATA2 SD Data 2 25 SDC1_DATA3 SD Data 3 31 SDC1_CLK SD Clock 32 VREG_SD SD Supply voltage 2.2.6. Others DWM-800B also provides some other interfaces listed in Table 2-7. Table 2-7 pins in MINI PCI-E SN. of the MINI PCI-E Volt Description W_DISABLE_N 20 2.6 The W_DISABLE# signal is an active low signal that when asserted (driven low) by the system shall disable radio operation. WAKE_N 1 2.6 The WAKE# signal is an open drain, active low signal that is driven low by a PCI Express Mini Card function to reactivate the PCI Express Link hierarchy’s main power rails and reference clocks. I2C_SCL 30 2.6 I2C Interface
12 I2C_SDA 32 2.6 I2C Interface SPI_SDI 3 Serial port control data input SPI_SDO 5 2.6 Serial port control data output SPI_CS# 6 2.6 Serial port control Chip Select SPI_SCLK 7 2.6 Serial Port Bit Clock 3. Electrical Characteristics and Safety Information 3.1. Absolute Maximum Ratings Absolute maximum rating for power supply and voltage on I/O pins of DWM-800B are list in table1 as follows. Table 3-1 Absolute maximum ratings Symbol Description Min Max Units VIO Voltage on any input or output pin -0.5 VPAD*+0.5 V VBAT POWER SUPPLY 3.3 3.9 V *VPAD=1.8V 3.2. Power-Up and Power-Down Sequence DWM-800B is Auto Power On when VBAT is ready. The system would be turned on. The pmic(MT6327) power on sequence is as below:
13 The CPU(MT6280) power on sequence is as below: 3.3. Operating conditions
14 3.4. RF Exposure Compliance The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or Transmitter. This device is intended only for OEM integrators under the following conditions: 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. End Product Labeling: This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may bemaintained between the antenna and users. The final end product must be labeled in a visible area with the following: “Contains FCC ID: KA2WM800BA1”. The grantee's FCC ID can be used only when all FCC compliance requirements are met. Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module.
15 The end user manual shall include all required regulatory information/warning as show in this manual. 4. Pins description of mini PCIE connector SN Definition Description Volt Remark 1 WAKE_N OUTPUT 1.8 The WAKE# signal is an open drain, active low signal that is driven low by a PCI Express Mini Card function to reactivate the PCI Express Link hierarchy’s main power rails and reference clocks. 3 SPI_SDI Serial port control data input 1.8 5 SPI_SDO Serial port control data output 1.8 7 SPI_SCLK Serial Port Bit Clock 1.8 9 GND Ground 11 Reserved Reserved Reserved For Future Use 13 SDC1_CMD SD Command/Response 1.8 15 GND Ground 17 SDC1_DATA0 SD Data 0 1.8 19 SDC1_DATA1 SD Data 1 1.8 21 GND Ground 23* SDC1_DATA2 SD Data 2 1.8 25* SDC1_DATA3 SD Data 3 1.8 27 GND Ground 29 GND Ground 31* SDC1_CLK SD Clock 1.8 33* Reserved Reserved Reserved For Future Use 35 GND Ground 37 GND Ground 39 VDD3V3 POWER 3.3 Power Supply 41 VDD3V3 POWER 3.3 Power Supply 43 GND Ground 45* PCM_CLK PCM Clock 1.8 47* PCM_SYNC PCM data strobe 1.8 49* PCM_OUT PCM data output 1.8 51* PCM_IN PCM data input 1.8 2 VDD3V3 POWER 3.3 Power Supply 4 GND Ground 6 SPI_CS# Serial port control Chip Select 1.8 8 VREG_USIM USIM Power 1.8 USIM Interface, USIM power 10 USIM_DATA USIM_DATA 1.8 USIM Interface 12 USIM_CLK USIM CLK 1.8 USIM Interface 14 USIM_RESET USIM_RESET 1.8 USIM Interface 16 Reserved Reserved Reserved For Future Use
16 18 GND Ground 20 W_DISABLE_N 2.6 The W_DISABLE# signal is an active low signal that when asserted (driven low) by the system shall disable radio operation. 22 EXT_RST_IN Reset 2.6 Reset module 24 VDD3V3 POWER 3.3 Power Supply 26 GND Ground 28 Reserved Reserved Reserved For Future Use 30 I2C_SCL I2C Clock 2.6 I2C Interface 32*** I2C_SDA/VMC_PMU I2C Data/VMC_PMU 2.6 I2C Interface and SD power combine 34 GND Ground 36 USB_HS_DP USB Data+ USB Interface 38 USB_HS_DM USB Data- USB Interface 40 GND Ground 42* Reserved Reserved Reserved For Future Use 44* Reserved Reserved Reserved For Future Use 46* SLIC_INT# SLIC_RESET# SLIC INT 48 SLIC_RESET# SLIC_RESET# SLIC RESET 50 GND Ground 52 VDD3V3 POWER 3.3 Power Supply * UART and PCM interfaces on the DWM-800B have been designed to be compatible with others so as to meet different needs. And we can make corresponding configuration for interfaces on the DWM-800B according to customer's requirements. * Please contact us to make sure if this pins could be used. Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
17 - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Navigation menu