D Link SR250NA1 Wireless N Service Router User Manual 2 of 2

D Link Corporation Wireless N Service Router 2 of 2

Contents

User manual 2 of 2

Unified Services Router User Manual 149 Symptom: Router can obtain an IP address, but PC is unable to load Internet pages. Recommended action: 1. Ask your ISP for the addresses of its designated Domain Name System (DNS) servers. Configure your PC to recognize those addresses. For details, see your operating system documentation. 2. On your PC, configure the router to be its TCP/IP gateway. 11.2 Date and time Symptom: Date shown is January 1, 1970. Possible cause: The router has not yet successfully reached a network time server (NTS). Recommended action: 1. If you have just configured the router, wait at least 5 minutes, select Administration > Time Zone, and recheck the date and time. 2. Verify your Internet access settings. Symptom: Time is off by one hour. Possible cause: The router does not automatically adjust for Daylight Savings Time. Recommended action: 1. Select Administration > Time Zone and view the current date and time settings. 2. Click to check or uncheck ―Automatically adjust for Daylight Savings Time‖, then click Apply. 11.3 Pinging to Test LAN Connectivity Most TCP/IP terminal devices and firewalls contain a ping utility that sends an ICMP echo-request packet to the designated device. The DSR responds with an echo reply. Troubleshooting a TCP/IP network is made very easy by using the ping utility in your PC or workstation. 11.3.1 Testing the LAN path from your PC to your router 1. From the PC‘s Windows toolbar, select Start > Run. 2. Type ping <IP_address> where <IP_address> is the router‘s IP address. Example: ping 192.168.10.1. 3. Click OK.
Unified Services Router User Manual 150 4. Observe the display:  If the path is working, you see this message sequence: Pinging <IP address> with 32 bytes of data Reply from <IP address>: bytes=32 time=NN ms TTL=xxx  If the path is not working, you see this message sequence: Pinging <IP address> with 32 bytes of data Request timed out 5. If the path is not working, Test the physical connections between PC and router  If the LAN port LED is off, go to the ―LED displays‖ section on page B-1 and follow instructions for ―LAN or Internet port LEDs are not lit.‖  Verify that the corresponding link LEDs are lit for your network interface card and for any hub ports that are connected to your workstation and firewall. 6. If the path is still not up, test the network configuration:  Verify that the Ethernet card driver software and TCP/IP software are installed and configured on the PC.  Verify that the IP address for the router and PC are correct and on the same subnet. 11.3.2 Testing the LAN path from your PC to a remote device 1. From the PC‘s Windows toolbar, select Start > Run. 2. Type ping -n 10 <IP_address> where -n 10 specifies a maximum of 10 tries and <IP address> is the IP address of a remote device such as your ISP‘s DNS server. Example: ping -n 10 10.1.1.1. 3. Click OK and then observe the display (see the previous procedure). 4. If the path is not working, do the following:  Check that the PC has the IP address of your firewall listed as the default gateway. (If the IP configuration of your PC is assigned by DHCP, this information is not visible in your PC‘s Network C ontrol Panel.)
Unified Services Router User Manual 151  Verify that the network (subnet) address of your PC is different from the network address of the remote device.  Verify that the cable or DSL modem is connected and functioning.  Ask your ISP if it assigned a hostname to your PC. If yes, select Network Configuration > WAN Settings > Ethernet ISP Settings and enter that hostname as the ISP account name.  Ask your ISP if it rejects the Ethernet MAC addresses of all but one of your PCs. Many broadband ISPs restrict access by allowing traffic from the MAC address of only your broadband modem; but some ISPs additionally restrict access to the MAC address of just a single PC connected to that modem. If this is the case, configure your firewall to clone or spoof the MAC address from the authorized PC. 11.4 Restoring factory-default configuration settings To restore factory-default configuration settings, do either of the following: 1. Do you know the account password and IP address?  If yes, select Administration > Settings Backup & Upgrade and click default.  If no, do the following: On the rear panel of the router, press and hold the Reset button about 10 seconds, until the test LED lights and then blinks. Release the button and wait for the router to reboot. 2. If the router does not restart automatically; manually restart it to make the default settings effective. 3. After a restore to factory defaults —whether initiated from the configuration interface or the Reset button — the following settings apply:  LAN IP address: 192.168.10.1  Username: admin  Password: password  DHCP server on LAN: enabled  WAN port configuration: Get configuration via DHCP
Chapter 12. Credits Microsoft, Windows are registered trademarks of Microsoft Corp. Linux is a registered trademark of Linus Torvalds. UNIX is a registered trademark of The Open Group.
Unified Services Router User Manual 154 Appendix A. Glossary ARP Address Resolution Protocol. Broadcast protocol for mapping IP addresses to MAC addresses. CHAP Challenge-Handshake Authentication Protocol. Protocol for authenticating users to an ISP. DDNS Dynamic DNS. System for updating domain names in real time. Allows a domain name to be assigned to a device with a dynamic IP address. DHCP Dynamic Host Configuration Protocol. Protocol for allocating IP addresses dynamically so that addresses can be reused when hosts no longer need them. DNS Domain Name System. Mechanism for translating H.323 IDs, URLs, or e-mail IDs into IP addresses. Also used to assist in locating remote gatekeepers and to map IP addresses to hostnames of administrative domains. FQDN Fully qualified domain name. Complete domain name, including the host portion. Example: serverA.companyA.com. FTP File Transfer Protocol. Protocol for transferring files between network nodes. HTTP Hypertext Transfer Protocol. Protocol used by web browsers and web servers to transfer files. IKE Internet Key Exchange. Mode for securely exchanging encryption keys in ISAKMP as part of building a VPN tunnel. IPsec IP security. Suite of protocols for securing VPN tunnels by authenticating or encrypting IP packets in a data stream. IPsec operates in either transport mode (encrypts payload but not packet headers) or tunnel mode (encrypts both payload and packet headers). ISAKMP Internet Key Exchange Security Protocol. Protocol for establishing security associations and cryptographic keys on the Internet. ISP Internet service provider. MAC Address Media-access-control address. Unique physical-address identifier attached to a network adapter. MTU Maximum transmission unit. Size, in bytes, of the largest packet that can be passed on. The MTU for Ethernet is a 1500-byte packet. NAT Network Address Translation. Process of rewriting IP addresses as a packet passes through a router or firewall. NAT enables multiple hosts on a LAN to access the Internet using the single public IP address of the LAN’s gateway router. NetBIOS Microsoft Windows protocol for file sharing, printer sharing, messaging, authentication, and name resolution. NTP Network Time Protocol. Protocol for synchronizing a router to a single clock on the network, known as the clock master. PAP Password Authentication Protocol. Protocol for authenticating users to a remote access server or ISP.
Unified Services Router User Manual 155 PPPoE Point-to-Point Protocol over Ethernet. Protocol for connecting a network of hosts to an ISP without the ISP having to manage the allocation of IP addresses. PPTP Point-to-Point Tunneling Protocol. Protocol for creation of VPNs for the secure transfer of data from remote clients to private servers over the Internet. RADIUS Remote Authentication Dial-In User Service. Protocol for remote user authentication and accounting. Provides centralized management of usernames and passwords. RSA Rivest-Shamir-Adleman. Public key encryption algorithm. TCP Transmission Control Protocol. Protocol for transmitting data over the Internet with guaranteed reliability and in-order delivery. UDP User Data Protocol. Protocol for transmitting data over the Internet quickly but with no guarantee of reliability or in-order delivery. VPN Virtual private network. Network that enables IP traffic to travel securely over a public TCP/IP network by encrypting all traffic from one network to another. Uses tunneling to encrypt all information at the IP level. WINS Windows Internet Name Service. Service for name resolution. Allows clients on different IP subnets to dynamically resolve addresses, register themselves, and browse the network without sending broadcasts. XAUTH IKE Extended Authentication. Method, based on the IKE protocol, for authenticating not just devices (which IKE authenticates) but also users. User authentication is performed after device authentication and before IPsec negotiation.
Appendix B. Factory Default Settings Feature Description Default Setting Device login User login URL http://192.168.10.1 User name (case sensitive) admin Login password (case sensitive) admin Internet Connection WAN MAC address Use default address WAN MTU size 1500 Port speed Autosense Local area network (LAN) IP address 192.168.10.1 IPv4 subnet mask 255.255.255.0 RIP direction None RIP version Disabled RIP authentication Disabled DHCP server Enabled DHCP starting IP address 192.168.10.2 DHCP ending IP address 192.168.10.100 Time zone GMT Time zone adjusted for Daylight Saving Time Disabled SNMP Disabled Remote management Disabled Firewall Inbound communications from the Internet Disabled (except traffic on port 80, the HTTP port) Outbound communications to the Internet Enabled (all) Source MAC filtering Disabled Stealth mode Enabled
Unified Services Router User Manual 158 Appendix C. Standard Services Available for Port Forwarding & Firewall Configuration ANY AIM BGP BOOTP_CLIENT BOOTP_SERVER CU-SEEME:UDP CU-SEEME:TCP DNS:UDP DNS:TCP FINGER FTP HTTP HTTPS ICMP-TYPE-3 ICMP-TYPE-4 ICMP-TYPE-5 ICMP-TYPE-6 ICMP-TYPE-7 ICMP-TYPE-8 ICMP-TYPE-9 ICMP-TYPE-10 ICMP-TYPE-11 ICMP-TYPE-13 ICQ IMAP2 IMAP3 IRC NEWS NFS NNTP PING POP3 PPTP RCMD REAL-AUDIO REXEC RLOGIN RTELNET RTSP:TCP RTSP:UDP SFTP SMTP SNMP:TCP SNMP:UDP SNMP-TRAPS:TCP SNMP-TRAPS:UDP SQL-NET SSH:TCP SSH:UDP STRMWORKS TACACS TELNET TFTP VDOLIVE
Unified Services Router User Manual 159 Appendix D. Log Output Reference Facility: System (Networking) Log Message Severity Log Message Severity DBUpdate event: Table: %s opCode:%d rowId:%d DEBUG BridgeConfig: too few arguments to command %s ERROR networkIntable.txt not found DEBUG BridgeConfig: too few arguments to command %s ERROR sqlite3QueryResGet failed DEBUG sqlite3QueryResGet failed.Query:%s ERROR Interface is already deleted in bridge DEBUG ddnsDisable failed ERROR removing %s from bridge %s... %s DEBUG sqlite3QueryResGet failed.Query:%s ERROR adding %s to bridge %s... %s DEBUG sqlite3QueryResGet failed.Query:%s ERROR stopping bridge... DEBUG ddnsDisable failed ERROR stopping bridge... DEBUG failed to call ddns enable ERROR stopping bridge... DEBUG ddnsDisable failed ERROR %s:DBUpdate event: Table: %s opCode:%d rowId:%d DEBUG sqlite3QueryResGet failed.Query:%s ERROR Wan is not up DEBUG Error in executing DB update handler ERROR %s:DBUpdate event: Table: %s opCode:%d rowId:%d DEBUG sqlite3QueryResGet failed.Query:%s ERROR doDNS:failed DEBUG Illegal invocation of ddnsView (%s) ERROR doDNS:failed DEBUG sqlite3QueryResGet failed.Query:%s ERROR doDNS:Result = FAILED DEBUG sqlite3QueryResGet failed.Query:%s ERROR doDNS:Result SUCCESS DEBUG ddns: SQL error: %s ERROR Write Old Entry: %s %s %s: to %s DEBUG Illegal operation interface got deleted ERROR Write New Entry: %s %s #%s : to %s DEBUG sqlite3QueryResGet failed.Query:%s ERROR Write Old Entry: %s %s %s: to %s DEBUG sqlite3QueryResGet failed.Query:%s ERROR Write New Entry: %s %s #%s : to %s DEBUG sqlite3QueryResGet failed.Query:%s ERROR ifStaticMgmtDBUpdateHandler: returning with " DEBUG ddnsDisable failed ERROR nimfLinkStatusGet: buffer: \ DEBUG ddns: SQL error: %s ERROR nimfLinkStatusGetErr: returning with status: %d DEBUG Failed to call ddns enable ERROR nimfAdvOptSetWrap: current Mac Option: %d DEBUG ddns: SQL error: %s ERROR nimfAdvOptSetWrap: current Port Speed Option: %d DEBUG sqlite3QueryResGet failed.Query:%s ERROR nimfAdvOptSetWrap: current Mtu Option: %d DEBUG Failed to call ddns enable ERROR nimfAdvOptSetWrap: looks like we are reconnecting. " DEBUG ddns: SQL error: %s ERROR nimfAdvOptSetWrap: Mtu Size: %d DEBUG ddnsDisable failed ERROR nimfAdvOptSetWrap: NIMF table is %s DEBUG ddns: SQL error: %s ERROR nimfAdvOptSetWrap:WAN_MODE TRIGGER DEBUG sqlite3QueryResGet failed.Query:%s ERROR nimfAdvOptSetWrap: MTU: %d DEBUG Failed to call ddns enable ERROR nimfAdvOptSetWrap: MacAddress: %s DEBUG ddns: SQL error: %s ERROR nimfAdvOptSetWrap: old Mtu Flag: %d DEBUG ddnsDisable failed ERROR
Unified Services Router User Manual 160 nimfAdvOptSetWrap: user has changed MTU option DEBUG ddns: SQL error: %s ERROR nimfAdvOptSetWrap: MTU: %d DEBUG sqlite3QueryResGet failed.Query:%s ERROR nimfAdvOptSetWrap: old MTU size: %d DEBUG sqlite3QueryResGet failed.Query:%s ERROR nimfAdvOptSetWrap: old Port Speed Option: %d DEBUG ddnsDisable failed ERROR nimfAdvOptSetWrap: old Mac Address Option: %d DEBUG ddns: SQL error: %s ERROR nimfAdvOptSetWrap: MacAddress: %s DEBUG sqlite3QueryResGet failed.Query:%s ERROR Setting LED [%d]:[%d] For %s DEBUG sqlite3QueryResGet failed.Query:%s ERROR l2tpEnable: command string: %s DEBUG ddnsDisable failed ERROR nimfAdvOptSetWrap: handling reboot scenario DEBUG failed to call ddns enable ERROR nimfAdvOptSetWrap: INDICATOR = %d DEBUG ddns: SQL error: %s ERROR nimfAdvOptSetWrap: UpdateFlag: %d DEBUG ddnsDisable failed ERROR nimfAdvOptSetWrap: returning with status: %s DEBUG sqlite3QueryResGet failed.Query:%s ERROR nimfGetUpdateMacFlag: MacTable Flag is: %d DEBUG Error in executing DB update handler ERROR nimfMacGet: Mac Option changed DEBUG Failed to open the resolv.conf file. Exiting./n ERROR nimfMacGet: Update Flag: %d DEBUG Could not write to the resolv.conf file. Exiting. ERROR nimfMacGet: MacAddress: %s DEBUG Error opening the lanUptime File ERROR nimfMacGet: MacAddress: %s DEBUG Error Opening the lanUptime File. ERROR nimfMacGet: MacAddress: %s DEBUG failed to open %s ERROR nimfMacGet: MacAddress: %s DEBUG failed to open %s ERROR nimfMacGet: MacAddress: %s DEBUG failed to query networkInterface table ERROR nimfMacGet:Mac option Not changed \ DEBUG failed to query networkInterface table ERROR nimfMacGet: MacAddress: %s DEBUG sqlite3QueryResGet failed.Query:%s ERROR nimfMacGet: MacAddress: %s DEBUG failed to enable IPv6 forwarding ERROR nimfMacGet: MacAddress: %s DEBUG failed to set capabilities on the " ERROR nimfMacGet: returning with status: %s DEBUG failed to enable IPv6 forwarding ERROR Now in enableing LanBridge function DEBUG failed to set capabilities on the " ERROR sucessfully executed the command %s DEBUG failed to disable IPv6 forwarding ERROR Now in disableing LanBridge function DEBUG failed to set capabilities on the " ERROR sucessfully executed the command %s DEBUG failed to open %s ERROR configPortTblHandler:Now we are in Sqlite Update " DEBUG Could not create ISATAP Tunnel ERROR The Old Configuration of ConfiPort was:%s DEBUG Could not destroy ISATAP Tunnel ERROR The New Configuration of ConfiPort was:%s DEBUG Could not configure ISATAP Tunnel ERROR The user has deselected the configurable port DEBUG Could not de-configure ISATAP Tunnel ERROR failed query %s DEBUG nimfStatusUpdate: updating NimfStatus failed ERROR failed query %s DEBUG nimfStatusUpdate: updating NimfStatus failed ERROR failed query %s DEBUG nimfLinkStatusGet: determinig link's status failed ERROR %s:DBUpdate event: Table: %s opCode:%d rowId:%d DEBUG nimfLinkStatusGet: opening status file failed ERROR
Unified Services Router User Manual 161 %s:DBUpdate event: Table: %s opCode:%d rowId:%d DEBUG Failed to commit ERROR %s:%d SIP ENABLE: %s DEBUG ifStatusDBUpdate: Failed to begin " ERROR sipTblHandler:failed to update ifStatic DEBUG %s: SQL error: %s ERROR sipTblHandler:failed to update Configport DEBUG %s: Failed to commit " ERROR %s:%d SIP DISABLE: %s DEBUG nimfNetIfaceTblHandler: unable to get LedPinId ERROR %s:%d SIP SET CONF: %s DEBUG nimfNetIfaceTblHandler: unable to get LedPinId ERROR Failed to open %s: %s DEBUG nimfNetIfaceTblHandler: unable to get LedPinId ERROR Failed to start sipalg DEBUG %s: unable to kill dhclient ERROR Failed to stop sipalg DEBUG nimfAdvOptSetWrap: unable to get current Mac Option ERROR Failed to get config info DEBUG nimfAdvOptSetWrap: unable to get current Port " ERROR Network Mask: 0x%x DEBUG nimfAdvOptSetWrap: unable to get current MTU Option ERROR RTP DSCP Value: 0x%x DEBUG nimfAdvOptSetWrap: error getting Mac Address from " ERROR Need more arguments DEBUG nimfAdvOptSetWrap: unable to get the MTU ERROR Invalid lanaddr DEBUG nimfAdvOptSetWrap: error setting interface advanced " ERROR Invalid lanmask DEBUG nimfAdvOptSetWrap: error getting MTU size ERROR Invalid option DEBUG nimfAdvOptSetWrap: unable to get Mac Address ERROR Failed to set config info DEBUG nimfAdvOptSetWrap: error setting interface advanced " ERROR Unknown option DEBUG nimfAdvOptSetWrap: failed to get old connectiontype ERROR sshdTblHandler DEBUG nimfAdvOptSetWrap: old connection type is: %s ERROR pPort: %s DEBUG nimfAdvOptSetWrap: failed to get old MTU Option ERROR pProtocol: %s DEBUG nimfAdvOptSetWrap: error getting MTU size ERROR pListerAddr: %s DEBUG nimfOldFieldValueGet: failed to get old " ERROR pKeyBits: %s DEBUG nimfOldFieldValueGet: user has changed MTU size ERROR pRootEnable: %s DEBUG nimfAdvOptSetWrap: failed to get old Port Speed " ERROR pRsaEnable: %s DEBUG nimfAdvOptSetWrap: user has changed Port Speed ERROR pDsaEnable: %s DEBUG nimfAdvOptSetWrap: failed to get old Mac Address " ERROR pPassEnable: %s DEBUG nimfAdvOptSetWrap: user has changed Mac Address " ERROR pEmptyPassEnable: %s DEBUG nimfAdvOptSetWrap: unable to get Mac Address ERROR pSftpEnable: %s DEBUG nimfAdvOptSetWrap:Failed to RESET the flag ERROR pScpEnable: %s DEBUG nimfAdvOptSetWrap: setting advanced options failed ERROR pSshdEnable: %s DEBUG nimfAdvOptSetWrap: interface advanced options applied ERROR
Unified Services Router User Manual 162 pPrivSep: %s DEBUG nimfGetUpdateMacFlag: unable to get Flag from MacTable ERROR %s:DBUpdate event: Table: %s opCode:%d rowId:%d DEBUG nimfMacGet: Updating MAC address failed ERROR Re-Starting sshd daemon.... DEBUG sqlite3QueryResGet failed.Query:%s ERROR sshd re-started successfully. DEBUG error executing the command %s ERROR sshd stopped . DEBUG error executing the command %s ERROR failed query %s DEBUG error executing the command %s ERROR vlan disabled, not applying vlan configuration.. DEBUG disableLan function is failed to disable ConfigPort" ERROR failed query %s DEBUG sqlite3QueryResGet failed.Query:%s ERROR failed query %s DEBUG sqlite3QueryResGet failed.Query:%s ERROR no ports present in this vlanId %d DEBUG Unable to Disable configurable port from ERROR failed query %s DEBUG configPortTblHandler has failed ERROR vlan disabled, not applying vlan configuration.. DEBUG sqlite3QueryResGet failed.Query:%s ERROR disabling vlan DEBUG Error in executing DB update handler ERROR enabling vlan DEBUG sqlite3QueryResGet failed ERROR vlan disabled, not applying vlan configuration.. DEBUG Failed to execute switchConfig for port\ ERROR no ports present in this vlanId %d DEBUG Failed to execute switchConfig for port enable ERROR failed query %s DEBUG Failed to execute ifconfig for port enable ERROR vlan disabled, not applying vlan configuration.. DEBUG Failed to execute ethtool for\ ERROR removing %s from bridge%s... %s DEBUG Failed to execute switchConfig for port disable ERROR adding %s to bridge%d... %s DEBUG Failed to execute ifconfig for port disable ERROR restarting bridge... DEBUG sqlite3QueryResGet failed ERROR [switchConfig] Ignoring event on port number %d DEBUG sqlite3_mprintf failed ERROR restarting bridge... DEBUG sqlite3QueryResGet failed ERROR executing %s ... %s DEBUG Failed to execute switchConfig for port mirroring ERROR removing %s from bridge%s... %s DEBUG Usage:%s <DB Name> <Entry Name> <logFile> <subject> ERROR adding %s to bridge%d... %s DEBUG sqlite3QueryResGet failed ERROR [switchConfig] Ignoring event on %s DEBUG Could not get all the required variables to email the Logs. ERROR restarting bridge... DEBUG runSmtpClient failed ERROR [switchConfig] Ignoring event on port number %d DEBUG getaddrinfo returned %s ERROR [switchConfig] executing %s ... %s DEBUG file not found ERROR restarting bridge... DEBUG sqlite3QueryResGet failed.Query:%s ERROR UserName: %s DEBUG sqlite3QueryResGet failed.Query:%s ERROR Password: %s DEBUG sqlite3QueryResGet failed.Query:%s ERROR IspName: %s DEBUG No memory to allocate ERROR DialNumber: %s DEBUG Failed to Open SSHD Configuration File ERROR Apn: %s DEBUG Ipaddress should be provided with accessoption 1 ERROR
Unified Services Router User Manual 163 GetDnsFromIsp: %s DEBUG Subnetaddress should be provided with accessoption 2 ERROR IdleTimeOutFlag: %s DEBUG Failed to restart sshd ERROR IdleTimeOutValue: %d DEBUG unable to open the " ERROR AuthMetho: %d DEBUG sqlite3QueryResGet failed.Query:%s ERROR executing %s ... %s DEBUG Error in executing DB update handler ERROR removing %s from bridge%d... %s DEBUG Error in executing DB update handler ERROR adding %s to bridge%d... %s DEBUG unknown vlan state ERROR stopping bridge... DEBUG Failed to execute vlanConfig binary for vlanId %d ERROR restarting bridge... DEBUG sqlite3_mprintf failed ERROR Could not configure 6to4 Tunnel Interface DEBUG Access port can be present only in single vlan ERROR Could not de-configure 6to4 Tunnel Interface DEBUG Failed to execute vlanConfig binary for vlanId %d ERROR failed to restart 6to4 tunnel interfaces DEBUG unknown vlan state ERROR BridgeConfig: too few arguments to command %s DEBUG Failed to execute vlanConfig binary for port number %d ERROR BridgeConfig: unsupported command %d DEBUG Failed to clear vlan for oldPVID %d ERROR BridgeConfig returned error=%d DEBUG Failed to execute vlanConfig binary for port number %d ERROR sqlite3QueryResGet failed DEBUG Failed to clear vlan for %d ERROR Error in executing DB update handler DEBUG Failed to set vlan entry for vlan %d ERROR sqlite3QueryResGet failed DEBUG Failed to set vlan entries, while enabling \ ERROR Failed to remove vlan Interface for vlanId \ DEBUG sqlite3QueryResGet failed ERROR sqlite3QueryResGet failed DEBUG Failed to execute vlanConfig binary for port number %d ERROR Invalid oidp passed DEBUG Failed to execute vlanConfig binary for vlanId %d ERROR Invalid oidp passed DEBUG Failed to enable vlan ERROR Failed to get oid from the tree DEBUG Failed to disable vlan ERROR threegEnable: Input to wrapper %s DEBUG Failed to set vlanPort table entries, while \ ERROR threegEnable: spawning command %s DEBUG Failed to enable vlan ERROR threegMgmtHandler: query string: %s DEBUG unknown vlan state ERROR threegMgmtHandler: returning with status: %s DEBUG Error in executing DB update handler ERROR adding to dhcprealy ifgroup failed DEBUG unknown vlan state ERROR adding to ipset fwDhcpRelay failed DEBUG Failed to execute vlanConfig binary for vlanId %d ERROR Disabling Firewall Rule for DHCP Relay Protocol DEBUG sqlite3_mprintf failed ERROR Enabling Firewall Rule for DHCP Relay Protocol DEBUG Access port can be present only in single vlan ERROR prerouting Firewall Rule add for Relay failed DEBUG Failed to execute vlanConfig binary for vlanId %d ERROR prerouting Firewall Rule add for Relay failed DEBUG unknown vlan state ERROR %s: SQL get query: %s DEBUG Failed to execute vlanConfig binary for port number %d ERROR %s: sqlite3QueryResGet failed DEBUG Failed to clear vlan for oldPVID %d ERROR %s: no result found DEBUG Failed to execute vlanConfig binary for port number %d ERROR
Unified Services Router User Manual 164 %s: buffer overflow DEBUG Failed to clear vlan for %d ERROR %s: value of %s in %s table is: %s DEBUG Failed to set vlan entry for vlan %d ERROR %s: returning with status: %s DEBUG Failed to set vlan entries, while enabling \ ERROR dnsResolverConfigure: addressFamily: %d DEBUG Failed to execute vlanConfig binary for port number %d ERROR dnsResolverConfigure: LogicalIfName: %s DEBUG Failed to execute vlanConfig binary for vlanId %d ERROR chap-secrets File found DEBUG Failed to enable vlan ERROR PID File for xl2tpd found DEBUG Failed to disable vlan ERROR pid: %d DEBUG Failed to set vlanPort table entries, while \ ERROR options.xl2tpd file found DEBUG Failed to enable vlan ERROR options.xl2tpd file not found DEBUG unknown vlan state ERROR Conf File for xl2tpd found DEBUG threegMgmtInit: unable to open the database file %s ERROR xl2tpd.conf not found DEBUG threegConnEnable: failed to get the WanMode ERROR Chap Secrets file found DEBUG threegEnable:spawning failed ERROR Chap Secrets file not found DEBUG threegDisable: unable to kill ppp daemon ERROR %s:DBUpdate event: Table: %s opCode:%d rowId:%d DEBUG threegMgmtHandler: Query: %s ERROR chap-secrets File found DEBUG threegMgmtHandler: error in executing database update ERROR PID File for pptpd found DEBUG Error in executing DB update handler ERROR pid: %d DEBUG are we getting invoked twice ?? ERROR PID File for pptpd interface found DEBUG could not open %s to append ERROR pid: %d DEBUG could not write nameserver %s to %s ERROR options.pptpd file found DEBUG could not write nameserver %s to %s ERROR options.pptpd file not found DEBUG could not open %s to truncate ERROR Conf File for pptpd found DEBUG dnsResolverConfigMgmtInit: unable to open the " ERROR pptpd.conf not found DEBUG resolverConfigDBUpateHandler: sqlite3QueryResGet " ERROR Chap Secrets file found DEBUG could not configure DNS resolver ERROR Chap Secrets file not found DEBUG dnsResolverConfigure: could not write nameserver:%s," ERROR %s:DBUpdate event: Table: %s opCode:%d rowId:%d DEBUG unboundMgmt: unable to open the " ERROR chap-secrets File found DEBUG ioctl call Failed-could not update active user Details ERROR pppoeMgmtTblHandler: MtuFlag: %d DEBUG sqlite3QueryResGet failed.Query:%s ERROR pppoeMgmtTblHandler: Mtu: %d DEBUG Can't kill xl2tpd ERROR pppoeMgmtTblHandler: IdleTimeOutFlag: %d DEBUG xl2tpd restart failed ERROR pppoeMgmtTblHandler: IdleTimeOutValue: %d DEBUG failed to get field value ERROR pppoeMgmtTblHandler: UserName: %s DEBUG failed to get field value ERROR pppoeMgmtTblHandler: Password: %s DEBUG sqlite3QueryResGet failed.Query:%s ERROR pppoeMgmtTblHandler: DNS specified: %s DEBUG sqlite3QueryResGet failed.Query:%s ERROR pppoeMgmtTblHandler: Service: %s DEBUG unboundMgmt: unable to open the " ERROR pppoeMgmtTblHandler: StaticIp: %s DEBUG writing options.xl2tpd failed ERROR
Unified Services Router User Manual 165 pppoeMgmtTblHandler: NetMask: %s DEBUG xl2tpdStop failed ERROR pppoeMgmtTblHandler: AuthOpt: %d DEBUG writing xl2tpd.conf failed ERROR pppoeMgmtTblHandler: Satus: %d DEBUG writing options.xl2tpd failed ERROR pppoeEnable: ppp dial string: %s DEBUG xl2tpdStop failed ERROR pppoeMgmtDBUpdateHandler: returning with status: %s DEBUG xl2tpdStart failed ERROR pptpMgmtTblHandler: MtuFlag: %d DEBUG sqlite3QueryResGet failed.Query:%s ERROR pptpMgmtTblHandler: Mtu: %d DEBUG writing Chap-secrets/Pap-Secrets failed ERROR pptpMgmtTblHandler: IdleTimeOutFlag: %d DEBUG xl2tpdStop failed ERROR pptpMgmtTblHandler: IdleTimeOutValue: %d DEBUG xl2tpdStart failed ERROR pptpMgmtTblHandler: GetDnsFromIsp: %d DEBUG sqlite3QueryResGet failed.Query:%s ERROR pptpMgmtTblHandler: UserName: %s DEBUG writing Chap-secrets/Pap-Secrets failed ERROR pptpMgmtTblHandler: Password: %s DEBUG xl2tpdStop failed ERROR pptpMgmtTblHandler: dynamic MyIp configured DEBUG xl2tpdStart failed ERROR pptpMgmtTblHandler: MyIp: %s DEBUG sqlite3QueryResGet failed.Query:%s ERROR pptpMgmtTblHandler: ServerIp: %s DEBUG writing Chap-secrets/Pap-Secrets failed ERROR pptpMgmtTblHandler: StaticIp: %s DEBUG Error in executing DB update handler ERROR pptpMgmtTblHandler: NetMask: %s DEBUG unboundMgmt: unable to open the " ERROR pptpMgmtTblHandler: MppeEncryptSupport: %s DEBUG Can't kill pptpd ERROR pptpMgmtTblHandler: SplitTunnel: %s DEBUG pptpd restart failed ERROR pptpEnable: ppp dial string: %s DEBUG Can't kill pptpd ERROR pptpEnable: spawning command %s DEBUG failed to get field value ERROR PID File for dhcpc found DEBUG failed to get field value ERROR pid: %d DEBUG unboundMgmt: unable to open the " ERROR pptpMgmtDBUpdateHandler: query string: %s DEBUG writing options.pptpd failed ERROR pptpMgmtDBUpdateHandler: returning with status: %s DEBUG pptpdStop failed ERROR dhcpcReleaseLease: dhcpc release command: %s DEBUG writing pptpd.conf failed ERROR dhcpcMgmtTblHandler: MtuFlag: %d DEBUG writing options.pptpd failed ERROR dhcpcMgmtTblHandler: Mtu: %d DEBUG pptpdStop failed ERROR DHCPv6 Server started successfully. DEBUG pptpdStart failed ERROR DHCPv6 Server stopped successfully DEBUG writing Chap-secrets/Pap-Secrets failed ERROR DHCPv6 Client started successfully. DEBUG Error in executing DB update handler ERROR DHCPv6 Client stopped successfully. DEBUG pppStatsUpdate: unable to get default MTU ERROR DHCPv6 Client Restart successful DEBUG pppoeMgmtInit: unable to open the database file %s ERROR l2tpMgmtTblHandler: MtuFlag: %d DEBUG pppoeDisable: unable to kill ppp daemon ERROR l2tpMgmtTblHandler: Mtu: %d DEBUG pppoeMultipleEnableDisable: pppoe enable failed ERROR l2tpMgmtTblHandler: IspName: %s DEBUG pppoeMultipleEnableDisable: pppoe disable failed ERROR
Unified Services Router User Manual 166 l2tpMgmtTblHandler: UserName: %s DEBUG pppoeMgmtTblHandler: unable to get current Mtu Option ERROR l2tpMgmtTblHandler: Password: %s DEBUG pppoeMgmtTblHandler: unable to get the Mtu ERROR l2tpMgmtTblHandler: AccountName: %s DEBUG pppoeMgmtTblHandler: pppoe enable failed ERROR l2tpMgmtTblHandler: DomainName: %s DEBUG pppoeMgmtDBUpdateHandler: failed query: %s ERROR l2tpMgmtTblHandler: Secret: not specified DEBUG pppoeMgmtDBUpdateHandler: error in executing " ERROR l2tpMgmtTblHandler: Secret: %s DEBUG pptpMgmtInit: unable to open the database file %s ERROR l2tpMgmtTblHandler: dynamic MyIp configured DEBUG pptpEnable: error executing command: %s ERROR l2tpMgmtTblHandler: MyIp: %s DEBUG pptpEnable: unable to resolve address: %s ERROR l2tpMgmtTblHandler: ServerIp: %s DEBUG pptpEnable: inet_aton failed ERROR l2tpMgmtTblHandler: StaticIp: %s DEBUG pptpEnable: inet_aton failed ERROR l2tpMgmtTblHandler: NetMask: %s DEBUG pptpEnable:spawning failed ERROR l2tpMgmtTblHandler: SplitTunnel: %s DEBUG pptpDisable: unable to kill ppp daemon ERROR needToStartHealthMonitor: returning with status: %s DEBUG pptpMgmtTblHandler: unable to get current MTU Option ERROR l2tpEnable: command string: %s DEBUG pptpMgmtTblHandler: unable to get the Mtu ERROR l2tpEnable: command: %s DEBUG pptpMgmtTblHandler: dbRecordValueGet failed for %s " ERROR l2tpEnable: command string: %s DEBUG pptpMgmtTblHandler: pptp enable failed ERROR PID File for dhcpc found DEBUG pptpMgmtTblHandler: pptp disable failed ERROR pid: %d DEBUG pptpMgmtDBUpdateHandler: sqlite3QueryResGet " ERROR l2tpMgmtDBUpdateHandler: query string: %s DEBUG pptpMgmtDBUpdateHandler: error in executing " ERROR l2tpMgmtDBUpdateHandler: returning with status: %s DEBUG Illegal invocation of dhcpConfig (%s) ERROR RADVD started successfully DEBUG dhcpLibInit: unable to open the database file %s ERROR RADVD stopped successfully DEBUG sqlite3QueryResGet failed.Query:%s ERROR empty update. nRows=%d nCols=%d WARN dhcpcMgmtInit: unable to open the database file %s ERROR Wan is not up or in load balencing mode WARN dhcpcReleaseLease: unable to release lease ERROR threegMgmtHandler: no row found. nRows = %d nCols = %d WARN dhcpcEnable: unable to kill dhclient ERROR pppoeMgmtDBUpdateHandler: empty update. WARN dhcpcEnable: enabling dhcpc failed on: %s ERROR dhcpcEnable: dhclient already running on: %s WARN dhcpcDisable: unable to kill dhclient ERROR dhcpcDisable: deleted dhclient.leases WARN dhcpcDisable: delete failed for dhclient.leases ERROR l2tpMgmtInit: unable to open the database file %s ERROR dhcpcDisable: failed to reset the ip ERROR l2tpEnable: unable to resolve address: %s ERROR dhcpcMgmtTblHandler: unable to get current Mtu Option ERROR l2tpEnable: inet_aton failed ERROR dhcpcMgmtTblHandler: unable to get the Mtu ERROR
Unified Services Router User Manual 167 The Enable Command is %s ERROR dhcpcMgmtTblHandler: dhclient enable failed ERROR l2tpEnable:Executing the Command failed ERROR dhcpcMgmtTblHandler: dhcpc release failed ERROR l2tpDisable: command string: %s ERROR dhcpcMgmtTblHandler: dhcpc disable failed ERROR l2tpDisable: unable to stop l2tp session ERROR dhcpcMgmtDBUpdateHandler: failed query: %s ERROR l2tpMgmtTblHandler: unable to get current MTU option ERROR dhcpcMgmtDBUpdateHandler: error in executing " ERROR l2tpMgmtTblHandler: unable to get the Mtu ERROR DHCPv6 Client start failed. ERROR l2tpMgmtTblHandler: dbRecordValueGet failed for %s " ERROR DHCPv6 Client stop failed. ERROR l2tpMgmtTblHandler: l2tpEnable failed ERROR failed to create/open DHCPv6 client " ERROR l2tpMgmtTblHandler: disabling l2tp failed ERROR failed to write DHCPv6 client configuration file ERROR l2tpMgmtDBUpdateHandler: sqlite3QueryResGet " ERROR failed to restart DHCPv6 Client ERROR l2tpMgmtDBUpdateHandler: error in executing ERROR failed to create/open DHCPv6 Server " ERROR Illegal invocation of tcpdumpConfig (%s) ERROR Restoring old configuration.. ERROR Failed to start tcpdump ERROR DHCPv6 Server configuration update failed ERROR Failed to stop tcpdump ERROR DHCPv6 Server Restart failed ERROR Invalid tcpdumpEnable value ERROR sqlite3QueryResGet failed.Query:%s ERROR Facility: System (VPN) Log Message Severity Log Message Severity %d command not supported by eapAuth DEBUG PEAP key derive: ERROR ERROR pCtx NULL. DEBUG PEAP context is NULL: ERROR ERROR Current cert subject name= %s DEBUG Constructing P2 response: ERROR ERROR X509_STORE_CTX_get_ex_data failed. DEBUG innerEapRecv is NULL: ERROR ERROR Cannot get cipher, no session est. DEBUG Decrypting TLS data: ERROR ERROR %s: SSL_ERROR_WANT_X509_LOOKUP DEBUG Wrong identity size: ERROR ERROR err code = (%d) in %s DEBUG Wrong size for extensions packet: ERROR ERROR BIO_write: Error DEBUG innerEapRecv is NULL: ERROR. ERROR Decrypting: BIO reset failed DEBUG Inner EAP processing: ERROR ERROR Encrypting BIO reset: ERROR DEBUG TLS handshake: ERROR. ERROR BIO_read: Error DEBUG Sending P1 response: ERROR ERROR EAP state machine changed from %s to %s. DEBUG Unexpected tlsGlueContinue return value. ERROR EAP state machine changed from %s to %s. DEBUG No more fragments in message. ERROR ERROR Received EAP Packet with code %d DEBUG No phase 2 data or phase 2 data buffer NULL: ERROR ERROR Response ID %d DEBUG Allocating memory for PEAP Phase 2 payload: ERROR ERROR Response Method %d DEBUG TLS encrypting response: ERROR ERROR
Unified Services Router User Manual 168 Created EAP/PEAP context: OK DEBUG Setting message in fragment buffer: ERROR ERROR Deleted EAP/PEAP context: OK DEBUG Allocating TLS read buffer is NULL: ERROR ERROR Upper EAP sent us: decision = %d method state = %d DEBUG Setting last fragment: ERROR ERROR P2 decision=(%d); methodState=(%d) DEBUG Getting message: ERROR ERROR Writing message to BIO: ERROR. DEBUG Processing PEAP message: ERROR ERROR Encrypted (%d) bytes for P2 DEBUG Setting fragment: ERROR ERROR P2: sending fragment. DEBUG Creating receive buffer: ERROR ERROR P2: message size = %d DEBUG Setting first fragment: ERROR ERROR P2: sending unfragmented message. DEBUG Sending P1 response: ERROR ERROR P1: Sending fragment. DEBUG NULL request (or response) PDU or NULL context: ERROR ERROR P1: Total TLS message size = (%d) DEBUG Expecting start packet, got something else: ERROR ERROR P1: sending unfragmented message. DEBUG Protocol version mismatch: ERROR ERROR peapFragFirstProcess: TLS record size to receive = (%d) DEBUG Processing PEAP message (from frag): ERROR ERROR Setting version %d DEBUG Processing PEAP message: ERROR ERROR PEAP pkt rcvd: data len=(%d) flags=(%d) version=(%d) DEBUG Processing PEAP message: ERROR ERROR Got PEAP/Start packet. DEBUG Indicated length not valid: ERROR ERROR Got first fragment DEBUG Did not get Acknowledged result: ERROR ERROR Got fragment (n) DEBUG Cannot understand AVP value: ERROR ERROR Got last fragment DEBUG eapExtResp is NULL: ERROR ERROR Got unfragmented message DEBUG eapWscCtxCreate: EAPAUTH_MALLOC failed. ERROR Got frag ack. DEBUG eapWscProcess: umiIoctl req to WSC failed, status = %d ERROR Ext AVP parsed: flags=(0x%x) DEBUG eapWscCheck: Invalid frame ERROR Mandatory bit not set: WARNING DEBUG eapWscBuildReq: Invalid state %d ERROR Ext AVP parsed: type=(%d) DEBUG eapWscProcessWscResp: Invalid data recd pData = %p, dataLen" ERROR Ext AVP parsed: value=(%d) DEBUG Data received for invalid context, dropping it ERROR Got PEAPv0 success! DEBUG eapWscProcessWscResp: Build Request failed ERROR Got PEAPv0 failure! DEBUG eapWscProcessWscResp: Invalid state %d ERROR pCtx NULL. DEBUG eapWscProcessWscResp: Message processing failed 0x%X ERROR Authenticator response check: Error DEBUG eapWscProcessWscData: Invalid notification recd %d ERROR Authenticator response check: Failed DEBUG unable to initialize MD5 ERROR MS-CHAP2 Response AVP size = %u DEBUG MDString: adpDigestInit for md5 failed ERROR Created EAP/MS-CHAP2 context: OK. DEBUG EAPAUTH_MALLOC failed. ERROR pCtx NULL. DEBUG EAPAUTH_MALLOC failed. ERROR Deleted EAP/MS-CHAPv2 context: OK DEBUG NULL context created: Error ERROR Not authenticated yet. DEBUG NULL context received: Error ERROR Authenticator response invalid DEBUG Authenticator ident invalid. ERROR EAP-MS-CHAPv2 password changed. DEBUG Success request message invalid: ERROR
Unified Services Router User Manual 169 Error rcvd. opCode %d. DEBUG Plugin context is NULL ERROR pCtx NULL. DEBUG Deriving implicit challenge: Error ERROR TLS message len changed in the fragment, ignoring. DEBUG Generating NT response: Error ERROR no data to send while fragment ack received. DEBUG NULL in/out buffer: Error ERROR TLS handshake successful. DEBUG Incorrect vendor id. ERROR Created EAP/TTLS context: OK DEBUG Allocating memory for outBuff: ERROR ERROR Deleted EAP/TTLS context: OK DEBUG AVP code not recognized ERROR No more fragments in message. ERROR DEBUG EAPAUTH_MALLOC failed. ERROR Upper EAP sent us: method state = %d; decision = %d DEBUG Converting password to unicode: Error ERROR P2: sending fragment. DEBUG Generating password hash: Error. ERROR P2 send unfragmented message. DEBUG Generating password hash hash: Error. ERROR P1: sending fragment. DEBUG Generating master key: Error. ERROR P1: sending unfragmented message. DEBUG Generating first 16 bytes of session key: Error.n ERROR \tTLSMsgLen = 0x%x DEBUG Generating second 16 bytes of session key: Error.n ERROR Send req ptr = 0x%x; Send resp ptr = 0x%x DEBUG Converting password to unicode: Error ERROR P2 decision=(%d); methodState=(%d) DEBUG Constructing failure response: ERROR ERROR Default EAP: method state = %d; decision = %d DEBUG Error checking authenticator response. ERROR TTLS pkt: data len=(%d) flags=(0x%x) DEBUG Error generating NT response. ERROR Got start DEBUG Username string more than 256 ASCII characters: ERROR ERROR Got first fragment (n). DEBUG Invalid Value-Size. ERROR Got fragment (n). DEBUG Invalid MS-Length. Got (%d), expected (%d) ERROR Got last fragment DEBUG Error constructing response. ERROR Got unfragmented message. DEBUG Got type (%d), expecting (%d) ERROR Got frag ack. DEBUG Cannot handle message; opCode = %d ERROR Rcvd. AVP Code-%u: flags-0x%x: len-%u: vendorId-%u: " DEBUG EAPAUTH_MALLOC failed. ERROR MOD EAP: method state from upper = %d; decision = %d DEBUG tlsGlueCtxCreate failed. ERROR Got AVP len = %ul. Should be less than 16777215 DEBUG client certificate must be set in the profile. ERROR AVP length extract: Error DEBUG received tls message length too big. ERROR pFB is NULL DEBUG total frags len > initial total tls length. ERROR Requesting message before assembly complete DEBUG total frags len > initial total tls length. ERROR pFB is NULL DEBUG total data rcvd(%d) doesnt match the initial " ERROR pFB is NULL DEBUG couldnt write %d data to TLS buffer. ERROR Buffer cannot hold message: ERROR DEBUG invalid flags %s passed to eapTlsBuildResp. ERROR pFB is NULL: Error DEBUG EAPAUTH_MALLOC failed. ERROR pFB is NULL DEBUG tlsGlueCtxCreate failed. ERROR TLS_FB* is NULL. DEBUG Context NULL: ERROR ERROR
Unified Services Router User Manual 170 pFB->msgBuff is NULL. DEBUG Setting profile to glue layer: ERROR. ERROR Error calculating binary. DEBUG _eapCtxCreate failed. ERROR Error calculating binary. DEBUG %d authentication not enabled in the system. ERROR adpDigestInit for SHA1 failed. DEBUG Initializing inner non-EAP auth plugin: ERROR ERROR adpDigestInit for SHA1 failed. DEBUG TTLS key derive: ERROR ERROR E = %d DEBUG TTLS context from EAP plugin is NULL: ERROR ERROR R = %d DEBUG Allocating memory for TTLS Phase 2 payload: ERROR ERROR Could not initialize des-ecb DEBUG TLS Encrypting response: ERROR ERROR adpDigestInit for MD4 failed. DEBUG Allocating TLS read buffer is NULL: ERROR ERROR adpDigestInit for SHA1 failed. DEBUG Inner authentication (id: %d) unhandled ERROR adpDigestInit for SHA1 failed. DEBUG innerEapRecv is NULL: ERROR. ERROR Error converting received auth reponse to bin. DEBUG Decrypting TLS data: ERROR ERROR Gnerating challenge hash: Error DEBUG Processing Phase 2 method: Error ERROR Generating password hash: Error DEBUG Writing message to BIO: ERROR. ERROR Generating challenge response: Error DEBUG TLS handshake: ERROR. ERROR Conn cipher name=%s ver=%s: %s DEBUG Unexpected tlsGlueContinue return value. ERROR Send req ptr = 0x%x; Send resp ptr = 0x%x DEBUG NULL request (or response) PDU or NULL context ERROR Request ptr = 0x%x; DEBUG Protocol version mismatch: ERROR ERROR Response ptr = 0x%x DEBUG Creating receive buffer: ERROR ERROR Rcvd. AVP Code - %ul DEBUG Setting first fragment: ERROR ERROR Rcvd. AVP flags - 0x%02x DEBUG Setting fragment: ERROR ERROR Rcvd. AVP len - %ul DEBUG Setting last fragment: ERROR ERROR Rcvd. AVP vendor id - %ul DEBUG Getting message: ERROR ERROR \tCode = %d DEBUG Processing TTLS message: ERROR ERROR \tIdent = %d DEBUG Processing TTLS message: ERROR ERROR \tLen = %d DEBUG Processing TTLS message: ERROR ERROR \tType = %d DEBUG Decapsulating AVP: ERROR ERROR \tOpCode = %d DEBUG Processing EAP receive: Error ERROR \tMSID = %d DEBUG AVP code not EAP: Error ERROR \tmsLen = %d DEBUG Encapsulating AVP: ERROR ERROR \tvalSize = %d DEBUG profile %s doesnt exist. ERROR Frag Buffer bytes left = (%d) DEBUG profile %s is in use. ERROR Stripped username=(%s) DEBUG profile %s already exists. ERROR digestLen = %d. DEBUG EAPAUTH_MALLOC failed ERROR ClearText = DEBUG User not found. ERROR CipherText = DEBUG EAP-MD5 not enabled in system configuration. ERROR digestLen = %d. DEBUG EAP-MSCHAPV2 not enabled in system configuration. ERROR digestLen1 = %d. DEBUG EAP-TLS not enabled in system configuration. ERROR digestLen2 = %d. DEBUG EAP-TTLS not enabled in system configuration. ERROR
Unified Services Router User Manual 171 password change is not allowed for this user DEBUG EAP-PEAP not enabled in system configuration. ERROR completed writing the policy DEBUG EAP-WSC not enabled in system configuration. ERROR completed writing the SA DEBUG PAP not enabled in system configuration. ERROR completed writing the proposal block DEBUG CHAP not enabled in system configuration. ERROR cmdBuf: %s DEBUG MSCHAP not enabled in system configuration. ERROR X509_DEBUG : Invalid Certificate for the generated" DEBUG MSCHAPV2 not enabled in system configuration. ERROR X590_ERROR : Failed to create File '%s' DEBUG PAP/Token not enabled in system configuration. ERROR x509TblHandler DEBUG EAP-MD5 not enabled in system configuration. ERROR pCertType: %s DEBUG EAP-MSCHAPV2 not enabled in system config. ERROR pRowQueryStr: %s DEBUG EAP-TLS not enabled in system configuration. ERROR x509SelfCertTblHandler DEBUG EAP-TTLS and EAP-PEAP are not valid as inner" ERROR pRowQueryStr: %s DEBUG invalid innerAuth %d. ERROR %s:DBUpdate event: Table: %s opCode:%d rowId:%d DEBUG profile %s doesnt exist. ERROR umiRegister failed ERROR Re-assembling fragments incorrect size ERROR eapAuthHandler: Invalid data received ERROR Error creating cipher context. ERROR EAPAUTH_MALLOC failed. ERROR Error initializing cipher context. ERROR malloc failed. ERROR Error creating digest context. ERROR BIO_new_mem_buf failed. ERROR Error initializing digest context. ERROR malloc failed. ERROR Error initializing DES in Klite ERROR BIO_new_mem_buf failed. ERROR Error initializing MD4 in Klite ERROR SSL_CTX_new (TLSv1_client_method) failed. ERROR Error initializing RC4 in Klite ERROR unable to set user configured CIPHER list %s ERROR Error initializing SHA in Klite ERROR Certificate verification failed. ERROR Error cleaning cipher context. ERROR Server name match failed. Got (%s) expected " ERROR Error destroying cipher context. ERROR SSL_CTX_use_certificate_file (cert, PEM) failed. ERROR Error cleaning digest context. ERROR SSL_CTX_use_PrivateKey_file failed. ERROR Error destroying digest context. ERROR private key does not match public key ERROR Error stripping domain name. ERROR SSL_CTX_load_verify_locations failed ERROR Error cleaning digest context. ERROR SSL_new failed. ERROR Error cleaning digest context. ERROR Both SSL_VERIFY_PEER and SSL_VERIFY_NONE set: Error ERROR Challenge not present in failure packet. ERROR EAPAUTH_MALLOC failed. ERROR Wrong challenge length. ERROR EAPAUTH_MALLOC failed. ERROR Incorrect password change version value. ERROR eapTimerCreate failed. ERROR Error generating password hash. ERROR eapCtxDelete:pCtx == NULL ERROR Error generating password hash. ERROR eapRole != EAP_ROLE_PEER or EAP_ROLE_AUTHENTICATOR ERROR Error encrypting password hash with block ERROR
Unified Services Router User Manual 172 pEapCtx == NULL or pPDU == NULL. ERROR Could not initialize des-ecb ERROR received EAP pdu bigger than EAP_MTU_SIZE. ERROR Error cleaning cipher context. ERROR received EAP pdu bigger than EAP_MTU_SIZE. ERROR Error cleaning cipher context. ERROR state machine is in invalid state. ERROR Error cleaning digest context. ERROR unable to create method context. ERROR Error cleaning digest context. ERROR method ctxCreate failed. ERROR adpDigestInit for SHA1 failed. ERROR method profile set failed. ERROR X509_ERROR : .Query:%s ERROR state machine is in invalid state. ERROR X509_ERROR : Invalid Certificate for the " ERROR Only StandAlone authenticator supported currently. ERROR invalid x509 certificate ERROR state machine is in invalid state. ERROR Couldn't get the x509 cert hash ERROR BuildReq operation failed ERROR Memory allocation failed ERROR No method ops defined for current method ERROR FileName too lengthy ERROR Process operation failed ERROR Couldn't execute command ERROR state machine is in invalid state. ERROR Memory allocation failed ERROR Packet length mismatch %d, %d ERROR Memory allocation failed ERROR eapAuthTypeToType: Invalid eapAuthType %d ERROR invalid certificate data ERROR eapTypeToAuthType: Invalid eapType %d ERROR .Query:%s ERROR unable to create method context. ERROR .Query:%s ERROR method ctxCreate failed. ERROR Memory allocation failed ERROR Invalid condition, methodState = %d, respMethod = %d ERROR X509_ERROR : Failed to validate the certficate " ERROR A EAP Ctx map already exists ERROR Memory allocation failed ERROR eapTimerCreate: Currently unsupported for Peer role ERROR .Query:%s ERROR eapTimerStart: Currently unsupported for Peer role ERROR Invalid Sign Key Length : %d ERROR eapTimerDestroy: Currently unsupported for Peer role ERROR Invalid Hash Alg : %d ERROR eapTimerCancel: Currently unsupported for Peer role ERROR Invalid Sign Alg : %d ERROR eapTimerHandler: Currently unsupported for Peer role ERROR No Memory Available ERROR pCtx is NULL: ERROR ERROR Certificate Request Failed ERROR tlsGlueCtxCreate failed ERROR File Open Failed ERROR eapVars is NULL ERROR File is Empty ERROR Context NULL: ERROR ERROR Memory Allocation Failed ERROR Initializing inner EAP auth: ERROR ERROR File Open Failed ERROR pCtx is NULL: ERROR ERROR File is Empty ERROR Memory Allocation Failed ERROR Error in executing DB update handler ERROR Facility: System (Admin) Log Message Severity Log Message Severity Usage:%s <DBFile> DEBUG unable to register to UMI ERROR
Unified Services Router User Manual 173 Could not open database: %s DEBUG sqlite3QueryResGet failed ERROR CPU LOG File not found DEBUG radSendtoServer: socket: %s ERROR MEM LOG File not found DEBUG radSendtoServer: bind() Failed: %s: %s ERROR cpuMemUsageDBUpdateHandler: update query: %s DEBUG radRecvfromServer: recvfrom() Failed: %s ERROR Printing the whole list after inserting DEBUG radRecvfromServer: Packet too small from %s:%d: %s ERROR %s at %d(minute) %d(hour) %d(dayOfMonth) %d(month)" DEBUG radCheckMsgAuth: Invalid Message-Authenticator length in" ERROR adpCmdExec exited with return code=%d DEBUG radDictLoad: couldn't open dictionary %s: %s ERROR %s op=%d row=%d DEBUG radBuildAndSendReq: Invalid Request Code %d ERROR sqlite3_mprintf failed DEBUG radPairAssign: bad attribute value length ERROR sqlite3QueryResGet failed: query=%s DEBUG radPairAssign: unknown attribute type %d ERROR Printing the whole list after delete DEBUG radPairNew: unknown attribute %d ERROR %s at %d(minute) %d(hour) %d(dayOfMonth) %d(month)" DEBUG radPairGen: Attribute(%d) has invalid length ERROR Printing the whole list after inserting DEBUG radPairValue: unknown attribute type %d ERROR %s at %d(minute) %d(hour) %d(dayOfMonth) %d(month)" DEBUG radPairValueLen: unknown attribute type %d ERROR email logs: No logging events enabled DEBUG radPairLocate: Attribute(%d) has invalid length ERROR %s DEBUG radPairUnpackDefault: Unknown-Attribute[%d]: ERROR Mail sent and the Database is reset. DEBUG radConfigure: can't open %s: %s ERROR Disabled syslog server DEBUG radConfigure: %s: line %d: bogus format: %s ERROR Event logs are full, sending logs to email DEBUG radConfAssert: No AuthServer Specified ERROR Email logs sending failed DEBUG radConfAssert: No Default Timeout Specified ERROR Packing attribute: %s DEBUG radConfAssert: No Default Retry Count Specified ERROR Server found: %s, secret: %s DEBUG radExtractMppeKey: Invalid MS-MPPE-Key Length ERROR Packed Auth. Reqest: code:%d, id:%d, len:%d DEBUG radVendorMessage: Invalid Length in Vendor Message ERROR Sending Packet to %x:%d .... DEBUG radVendorMessage: Unknown Vendor ID received:%d ERROR Receiving Reply Packet.... DEBUG radVendorAttrGet: Invalid Length in Vendor Message ERROR Verified Reply Packet Integrity DEBUG radVendorAttrGet: Unknown Vendor ID:%d ERROR Generated Reply Attribute-Value pairs DEBUG radVendorMessagePack: Unknown Vendor ID:%d ERROR Verified Message-Authenticator DEBUG radGetIPByName: couldn't resolve hostname: %s ERROR Unloaded RADIUS Dictionary DEBUG radGetHostIP: couldn't get hostname ERROR Adding Dictionary Attribute %s DEBUG radGetHostIP: couldn't get host IP address ERROR Adding Dictionary Value %s DEBUG radius dictionary loading failed ERROR Loaded Dictionary %s DEBUG Failed to set default timeout value ERROR
Unified Services Router User Manual 174 Adding Dictionary Attribute '%s' DEBUG Failed to set default retries value ERROR Adding Dictionary Value %s DEBUG ERROR: incomplete DB update information. ERROR Receiving attribute: %s DEBUG old values result does not contain 2 rows ERROR Processing attribute: %s DEBUG sqlite3QueryResGet failed ERROR Processing attribute: %s DEBUG empty update. nRows=%d nCols=%d ERROR Processing attribute: %s DEBUG Error in executing DB update handler ERROR Processing attribute: %s DEBUG sqlite3QueryResGet failed ERROR radConfGet: " DEBUG Invalid SQLITE operation code - %d ERROR Added Server %s:%d with " DEBUG sqlite3QueryResGet failed ERROR Added Server %s:%d with " DEBUG empty result. nRows=%d nCols=%d ERROR Default Timeout Set to %d DEBUG sqlite3QueryResGet failed ERROR Default Retry Count Set to %d DEBUG empty result. nRows=%d nCols=%d ERROR %s - %s : %d DEBUG RADIUS Accounting Exchange Failed ERROR Deleting Server %s:%d with " DEBUG Unable to set debug for radAcct. ERROR Adding RowId:%d to Server %s:%d with " DEBUG Unable to set debug level for radAcct. ERROR rowIds: %d - %d DEBUG ERROR: option value not specified ERROR Deleting Server %s:%d with " DEBUG ERROR: option value not specified ERROR RADIUS Deconfigured DEBUG Unable to initialize radius ERROR Found Option %s on line %d of file %s DEBUG radEapMsgQueueAdd: Invalid EAP packet length(%d) ERROR Setting Option %s with value %s DEBUG radEapRecvTask: invalid EAP code:%d ERROR RADIUS Configured DEBUG radEapRecvTask: Packet length mismatch %d, %d ERROR %d : Server %s:%d with " DEBUG No attributes received in Access-Challenge message ERROR DBUpdate event: Table: %s opCode:%d rowId:%d DEBUG No State Attribute in Access-Challenge message ERROR Host IP address: %s DEBUG radEapRecvTask: " ERROR Adding Packet for existing cookie:%p DEBUG failed to initialize UMI ERROR Adding Packet and cookie:%p DEBUG umiRegister failed. errno=%d ERROR Releasing Packet and cookie:%p DEBUG Invalid arguments to ioctl handler ERROR Releasing Packet with cookie:%p DEBUG radEapSendRtn: Invalid Arguments ERROR Received EAP-Identity from Pnac: %s DEBUG radEapSendRtn: failed to allocate buffer ERROR Filling User-Name: %s DEBUG umiIoctl failed ERROR Filling State: DEBUG failed to initialize EAP message queue ERROR Filling EAP-Message: DEBUG Unable to set debug for radEap. ERROR Filling Service-Type: %d DEBUG Unable to set debug level for radEap. ERROR Filling Framed-MTU: %d DEBUG ERROR: option value not specified ERROR Received Access-Challenge from Server DEBUG ERROR: option value not specified ERROR Sending Reply EAP Packet to Pnac DEBUG could not initialize MGMT framework ERROR Error sending packet to Pnac DEBUG Unable to initialize radius ERROR RADIUS Authentication Failed; " DEBUG Unable to set debug for radEap. ERROR RADIUS Authentication Successful; " DEBUG Unable to set debug level for radEap. ERROR Got Packet with cookie:%p DEBUG ERROR: option value not specified ERROR Next DNS Retry after 1 min DEBUG Unable to initialize radius ERROR Next Synchronization after" DEBUG Invalid username or password ERROR
Unified Services Router User Manual 175 Next Synchronization after" DEBUG Unable to set debug for radAuth. ERROR Next Synchronization after %d \ DEBUG Unable to set debug level for radAuth. ERROR Primary is not available, " DEBUG ERROR: option value not specified ERROR Secondary is not available, " DEBUG Unable to initialize radius ERROR Invalid value for use default servers, " DEBUG Invalid username, challenge or response ERROR No server is configured, " DEBUG Unable to set debug for radAuth. ERROR Backing off for %d seconds DEBUG Unable to set debug level for radAuth. ERROR Requesting time from %s DEBUG ERROR: option value not specified ERROR Synchronized time with %s DEBUG Unable to initialize radius ERROR Received KOD packet from %s DEBUG Invalid username or password ERROR No suitable server found %s DEBUG usage : %s <DB fileName> ERROR Received Invalid Length packet from %s DEBUG ntpd : umi initialization failed ERROR Received Invalid Version packet from %s DEBUG ntpd : ntpInit failed ERROR Received Invalid Mode packet from %s DEBUG ntpd : ntpMgmtInit failed ERROR Request Timed out from %s DEBUG There was an error while getting the timeZoneChangeScript." ERROR Looking Up %s DEBUG unexpected reply from %d cmd=%d ! ERROR Timezone difference :%d DEBUG cmd %d not supported. caller %d ERROR Could not open file: %s DEBUG default reached ERROR Could not read data from file DEBUG Unable to initialize ntpControl ERROR ntpTblHandler DEBUG ntpMgmt : Couldn't open database %s ERROR status: %d DEBUG ERROR : incomplete DB update information ERROR tz: %d DEBUG empty update. nRows=%d nCols=%d ERROR DayLightsaving: %d DEBUG Error in executing DB update handler ERROR pNtpControl->ServerNames[PRIMARY_SERVER]: %s DEBUG requestNtpTime: Invalid addr ERROR pNtpControl->ServerNames[SECONDARY_SERVER]: %s DEBUG failed to take lock for compId: %d ERROR DS: %d DEBUG failed to convert ioctl args to buffer for" ERROR pPriServ %s DEBUG request timeout dst(%d) <-- src(%d) ERROR pSecServ %s DEBUG failed to take lock for compId: %d ERROR Making request from %d --> %d DEBUG umiIoctlArgsToBuf: failed to allocate memory ERROR sent request dst(%d) <-- src(%d) using option %d DEBUG umiRecvFrom: could not allocate memory ERROR received request too small!(%d bytes) DEBUG adpMalloc failed ERROR Received a UMI request from %d DEBUG context with ID: %d already registered ERROR sent a reply src(%d) ---> dst(%d) DEBUG Failed to allocate memory for creating UMI context ERROR umiRegister (%x,%x,%x,%x) DEBUG Failed to create recvSem for UMI context ERROR srcId=%d(%s) --> destId=%d(%s) cmd=%d inLen=%d outLen=%d DEBUG Failed to create mutex locks for UMI context ERROR waiting for reply...Giving Up DEBUG Failed to create mutex recvQLock for UMI context ERROR No request in the list after semTake DEBUG Invalid arguments to umiIoctl ERROR reply timeout DEBUG could not find the destination context ERROR
Unified Services Router User Manual 176 timeout after semTake DEBUG memPartAlloc for %d size failed ERROR srcId=%d(%s) <-- destId=%d(%s) cmd=%d DEBUG memPartAlloc for %d size failed ERROR Un-registerting component with Id %d DEBUG No Handler registered for this UMI context ERROR failed to send ioctl request: dst(%d) <--- src(%d) DEBUG Couldn't find component with ID (%d)," ERROR processed a reply dst(%d) <-- src(%d) DEBUG id=%d handler=%x ERROR request with no result option dst(%d) <-- src(%d) DEBUG Received NULL buffer in umiBufToIoctlArgs() ERROR cmd = %s DEBUG usbMgmtInit: unable to open the database file %s ERROR cmdstring is %s %s:%d DEBUG call to printConfig failed ERROR Calling printerConfig binary ... DEBUG Failed to Disable Network Storage" ERROR Calling unmount for USB ... DEBUG Some error occurred while removing device ERROR Calling mount for USB ... DEBUG Some error occurred while removing device ERROR usbdevice is %d %s:%d DEBUG Sqlite update failed ERROR Query string: %s DEBUG Failed to enable printer properly ERROR sqlite3QueryResGet failed.Query:%s DEBUG Failed to mount device on system ERROR %s: 1. usb is already disconnected for old usb type. " DEBUG Failed to enable network storage device" ERROR %s: 2.call disable for new usb type ! DEBUG Failed to mount device on system ERROR %s: 3. usb is already disconnected for old usb type. " DEBUG Sqlite update failed ERROR %s: 4. Disabled old usb type . Now " DEBUG USB1 Touch failed ERROR usbdevice is %d %s:%d DEBUG USB2 Touch failed ERROR USB: failed to begin transaction: %s DEBUG Sqlite update failed ERROR USB: SQL error: %s pSetString = %s DEBUG Failed query: %s ERROR USB: failed to commit transaction: %s DEBUG Failed to execute usb database update handler ERROR USB: updated table: %s DEBUG Usage:%s <DBFile> <opType> <tblName> <rowId> ERROR USB: returning with status: %s DEBUG Illegal invocation of snmpConfig (%s) ERROR %s:DBUpdate event: Table: %s opCode:%d rowId:%d DEBUG Invalid Community Access Type ERROR executing %s status =%d DEBUG Invalid User Access Type ERROR executing %s DEBUG Invalid Security Level ERROR %s returned status=%d DEBUG Invalid Authentication Algorithm ERROR %s returned status=%d DEBUG Invalid Privacy Algorithm ERROR snmpd.conf not found DEBUG Invalid Argument ERROR [SNMP_DEBUG] : Fwrite Successful DEBUG Failed to allocate memory for engineID ERROR [SNMP_DEBUG] : Fwrite failed DEBUG [SNMP_DEBUG]: Failed to get host address ERROR radPairGen: received unknown attribute %d of length %d WARN [SNMP_DEBUG] : FOPEN failed ERROR radPairGen: %s has unknown type WARN sqlite3QueryResGet failed.Query:%s ERROR radPairLocate: unknown attribute %ld of length %d WARN sqlite3QueryResGet failed.Query:%s ERROR radPairLocate: %s has unknown type WARN Invalid Security Level ERROR Illegal invocation of cpuMemUsage (%s) ERROR Invalid Authentication Algorithm ERROR
Unified Services Router User Manual 177 cpuMemUsageDBUpdateHandler: SQL error: %s ERROR Invalid Privacy Algorithm ERROR unable to open the DB file %s ERROR Failed to Get Host Address ERROR umiInit failed ERROR Invalid version ERROR unable to register to UMI ERROR snmp v3 Trap Configuration Failed ERROR Error Reading from the Database. ERROR sqlite3QueryResGet failed query:%s ERROR short DB update event request! ERROR sqlite3QueryResGet failed.Query:%s ERROR Error in executing DB update handler ERROR Failed to Open Snmp Configuration File ERROR adpListNodeRemove : Returned with an error ERROR Failed to write access control entries ERROR command too long. Try increasing " ERROR Failed to write snmpv3 users entries ERROR failed to allocate memory for CRON_NODE ERROR Failed to write snmp trap entries ERROR sqlite3QueryResGet failed ERROR Failed to write system entries. ERROR There was an error while reading the schedules. ERROR Failed to restart snmp ERROR unable to register to UMI ERROR %s failed with status ERROR short DB update event request! ERROR Error in executing DB update handler ERROR malloc(DB_UPDATE_NODE) failed ERROR %s: Unable to open file: %s ERROR short ifDev event request! ERROR RADVD start failed ERROR sqlite3_mprintf failed ERROR RADVD stop failed ERROR no component id matching %s ERROR failed to create/open RADVD configuration file %s ERROR umiIoctl (%s, UMI_CMD_DB_UPDATE(%d)) failed. ERROR Restoring old configuration.. ERROR sqlite3_mprintf failed ERROR failed to write/update RADVD configuration file ERROR sqlite3_mprintf failed ERROR upnpDisableFunc failed ERROR no component id matching %s ERROR upnpEnableFunc failed ERROR umiIoctl (%s, UMI_CMD_IFDEV_EVENT(%d)) failed. ERROR sqlite3QueryResGet failed.Query:%s ERROR klogctl(9) failed ERROR Error in executing DB update handler ERROR malloc failed for %d bytes ERROR unable to open the DB file %s ERROR klogctl(4) failed ERROR umiInit failed ERROR emailLogs: Invalid Number of Arguments!! Exiting. ERROR unable to register to UMI ERROR sqlite3QueryResGet failed ERROR short DB update event request! ERROR Could not execute the smtpClient. ERROR short ifDev event request! ERROR Error while cleaning the database.Exiting. %s ERROR sqlite3_mprintf failed ERROR %s failed. status=%d ERROR Facility: System (Firewall) Log Message Severity Log Message Severity Enabling rule for protocol binding. DEBUG Disable all NAT rules. DEBUG Disabling rule for protocol binding. DEBUG Enable all NAT rules. DEBUG Enabling Remote SNMP on WAN. DEBUG Enabling NAT URL filter rules. DEBUG Disabling Remote SNMP on WAN DEBUG Restarting all NAT rules. DEBUG
Unified Services Router User Manual 178 wan traffic counters are restared DEBUG Deleting schedule based firewall rules. DEBUG Traffic limit has been reached DEBUG Deleting schedule based firewall rules from DB. DEBUG Traffic meter monthly limit has been changed to %d. DEBUG Update schedule based firewall rules in DB. DEBUG Enabling traffic meter for only dowload. DEBUG Restart schedule based firewall rules. DEBUG Enabling traffic meter for both directions. DEBUG inter vlan routing enabled DEBUG Enabling traffic meter with no limit. DEBUG inter vlan routing disabled DEBUG Email alert in traffic meter disabled. DEBUG Disabling Content Filter for %d DEBUG Email alert in traffic meter enabled. DEBUG Enabling Content Filter for %d DEBUG Traffic Meter:Monthly limit %d MB has been " DEBUG ./src/firewall/linux/user/firewalld.c:59:#undef ADP_DEBUG2 DEBUG Traffic Metering: Adding rule to drop all traffic DEBUG ./src/firewall/linux/user/firewalld.c:61:#define ADP_DEBUG2 printf DEBUG Traffic Metering: %sabling Email traffic DEBUG Enabling Source MAC Filtering DEBUG Disabling attack checks for IPv6 rules. DEBUG Disabling Source MAC Filtering DEBUG Enabling attack checks for IPv6 rules. DEBUG Adding MAC Filter Policy for Block & Permit Rest DEBUG Configuring one to one NAT settings with %s private start IP " DEBUG Adding MAC Filter Policy for Permit & Block Rest DEBUG Deleting forward one to one NAT having setting %s private start" DEBUG Restarting Source MAC Address Policy DEBUG Disabling attack check for Block ping to WAN interface. DEBUG Disabling Firewall Rule for DHCP Relay Protocol DEBUG Disabling attack check for Stealth mode for tcp DEBUG Enabling Firewall Rule for DHCP Relay Protocol DEBUG Disabling attack check for Stealth mode for udp DEBUG prerouting Firewall Rule add for Relay failed DEBUG Disabling attack check for TCP Flood. DEBUG prerouting Firewall Rule add for Relay failed DEBUG Disabling attack check for UDP Flood. DEBUG Deleting MAC Filter Policy for Address %s DEBUG Disabling attack check for IPsec. DEBUG Adding MAC Filter Policy for Address %s DEBUG Disabling attack check for PPTP. DEBUG Disabling Firewall Rules for DMZ host DEBUG Disabling attack check for L2TP. DEBUG Enabling Firewall Rules for DMZ host DEBUG Disabling attack check for UDP Flood. DEBUG Disabling Firewall Rules for Spill Over Load Balancing DEBUG Disabling attack check for IPsec. DEBUG Disabling Firewall Rules for Load Balancing DEBUG Disabling attack check for PPTP. DEBUG Enabling Firewall Rules for Load Balancing DEBUG Disabling attack check for L2TP. DEBUG Enabling Firewall Rules for Spill Over Load Balancing DEBUG Enabling attack check for Block ping to WAN " DEBUG Enabling Firewall Rules for Auto Failover DEBUG Enabling attack check for Stealth Mode for tcp. DEBUG Enabling Firewall Rules for Load Balancing . DEBUG Enabling attack check for Stealth Mode for udp. DEBUG Enabling Firewall Rules for Spill Over Load Balancing . DEBUG Enabling attack check for TCP Flood. DEBUG Enabling Firewall Rules for Auto Failover DEBUG Enabling attack check for UDP Flood. DEBUG Deleting BlockSites Keyword \ DEBUG Enabling attack check for IPsec. DEBUG Enabling BlockSites Keyword \ DEBUG Enabling attack check for PPTP. DEBUG Disabling BlockSites Keyword \ DEBUG
Unified Services Router User Manual 179 Enabling attack check for L2TP. DEBUG Updating BlockSites Keyword from \ DEBUG Enabling attack check for UDP Flood. DEBUG Inserting BlockSites Keyword \ DEBUG Enabling attack check for IPsec. DEBUG Deleting Trusted Domain \ DEBUG Enabling attack check for PPTP. DEBUG Adding Trusted Domain \ DEBUG Enabling attack check for L2TP. DEBUG Restarting Schedule Based Firewall Rules DEBUG Enabling DoS attack check with %d SyncFlood detect rate, " DEBUG Enabling Remote SNMP DEBUG Disabling DoS attack check having %d SyncFlood detect rate," DEBUG Disabling Remote SNMP DEBUG Enabling ICSA Notification Item for ICMP notification. DEBUG Enabling Remote SNMP DEBUG Enabling ICSA Notification Item for Fragmented Packets. DEBUG Disabling DOS Attacks DEBUG Enabling ICSA Notification Item for Multi cast Packets. DEBUG Enabling DOS Attacks DEBUG Disabling ICSA Notification Item for ICMP notification. DEBUG Enabling DOS Attacks DEBUG Disabling ICSA Notification Item for Fragmented Packets. DEBUG Restarting Firewall [%d]:[%d] For %s DEBUG Disabling ICSA Notification Item for Multi cast Packets. DEBUG restartStatus = %d for LogicalIfName = %s DEBUG Adding IP/MAC binding rule for %s MAC address " DEBUG Deleting Lan Group %s DEBUG Deleting IP/MAC binding rule for %s MAC " DEBUG Adding Lan Group %s DEBUG ./src/firewall/linux/user/firewalld.c:60:#undef ADP_DEBUG DEBUG Deleting lan host %s from group %s DEBUG ./src/firewall/linux/user/firewalld.c:62:#define ADP_DEBUG printf DEBUG Adding lan host %s from group %s DEBUG Restarting traffic meter with %d mins, %d hours, " DEBUG Disabling Firewall Rule for IGMP Protocol DEBUG Updating traffic meter with %d mins, %d hours, " DEBUG Enabling Firewall Rule for IGMP Protocol DEBUG Deleting traffic meter. DEBUG Deleting IP/MAC Bind Rule for MAC address %s and IP " DEBUG Disabling block traffic for traffic meter. DEBUG Adding IP/MAC Bind Rule for MAC address %s and IP DEBUG Enabling traffic meter. DEBUG Deleting Protocol Bind Rule for Service %s DEBUG Adding lan group %s. DEBUG Deleting Protocol Bind Rule for Service %s DEBUG Deleting lan group %s. DEBUG Deleting Protocol Bind Rule for Service %s DEBUG Renaming lan group from %s to %s. DEBUG Adding Protocol Bind Rule for Service %s DEBUG Deleting host %s from %s group. DEBUG %s Session Settings DEBUG Adding host %s to %s group. DEBUG Restarting IPv6 Firewall Rules... DEBUG Enabling Keyword blocking for %s keyword. DEBUG Deleting Port Trigger Rule for %d:%d:%d:%d:%d DEBUG Disabling keyword Blocking for %s keyword . DEBUG Deleting Port Trigger Rule for %d:%d:%d:%d:%d DEBUG Deleting trusted domain with keyword %s. DEBUG Enabling Port Trigger Rule for %d:%d:%d:%d:%d DEBUG Adding %s keyword to trusted domain. DEBUG Disabling Port Trigger Rule for %d:%d:%d:%d:%d DEBUG Enabling Management Access from DEBUG Enabling Port Trigger Rule for DEBUG
Unified Services Router User Manual 180 Internet on port %d %d:%d:%d:%d:%d Enabling remote access management for IP address range" DEBUG Disabling Port Trigger Rule for %d:%d:%d:%d:%d DEBUG Enabling remote access management to only this PC. DEBUG Adding Port Trigger Rule for %d:%d:%d:%d:%d DEBUG Disabling Management Access from Internet on port %d DEBUG Enabling Content Filter DEBUG Disabling remote access management for IP address range" DEBUG Disabling Content Filter DEBUG Disabling remote access management only to this PC. DEBUG Enabling Content Filter DEBUG MAC Filtering %sabled for BLOCK and PERMIT REST. DEBUG Setting NAT mode for pLogicalIfName = %s DEBUG MAC Filtering %sabled for PERMIT and BLOCK REST. DEBUG Enabling DROP for INPUT DEBUG Enabling Content Filtering. DEBUG Enabling DROP for FORWARD DEBUG Disabling Content Filtering. DEBUG Enabling NAT based Firewall Rules DEBUG Deleting rule, port triggering for protocol TCP. DEBUG Setting transparent mode for pLogicalIfName \ DEBUG Deleting rule, port triggering for protocol UDP. DEBUG Enabling Accept for INPUT DEBUG Deleting rule, port triggering for protocol TCP. DEBUG Enabling Accept for FORWARD DEBUG Deleting rule, port triggering for protocol UDP. DEBUG Setting Routing mode for pLogicalIfName \ DEBUG Enabling rule, port triggering for protocol TCP. DEBUG Enabling DROP for INPUT DEBUG Enabling rule, port triggering for protocol UDP. DEBUG Enabling DROP for FORWARD DEBUG Enabling rule, port triggering for protocol TCP. DEBUG Disabling NAT based Firewall Rules DEBUG Enabling rule, port triggering for protocol UDP. DEBUG Enabling Firewall Rules for URL Filtering & " DEBUG Enabling DNS proxy. DEBUG Adding Firewall Rule for RIP Protocol DEBUG Restarting DNS proxy. DEBUG Restarting Schedule Based Firewall Rules DEBUG checking DNS proxy for Secure zone. DEBUG enabling IPS checks between %s and %s zones. DEBUG checking DNS proxy for Public zone. DEBUG disabling IPS checks between %s and %s zones. DEBUG Enabling Block traffic from %s zone. DEBUG Stopping IPS...%s DEBUG Configuring firewall session settings for " DEBUG IPS started. DEBUG Disabling DMZ DEBUG Route already exists DEBUG Disabling WAN-DMZ rules . DEBUG Route addition failed: Network Unreachable DEBUG Enabling WAN DMZ rules . DEBUG Route addition failed: Network is down DEBUG Restarting DMZ rule having %s address with %s address. DEBUG Route addition failed DEBUG Enabling LAN DHCP relay. DEBUG Failed to add rule in iptables DEBUG OneToOneNat configured successfully DEBUG Failed to delete rule from iptables DEBUG OneToOneNat configuration failed DEBUG fwLBSpillOverConfigure: Something going wrong here ERROR Deleting scheduled IPv6 rules. DEBUG fwLBSpillOverConfigure: unable to get interfaceName ERROR delete from FirewallRules6 where ScheduleName = '%s'. DEBUG fwLBSpillOverConfigure: Could not set PREROUTING rules ERROR
Unified Services Router User Manual 181 Update FirewallRules6 where ScheduleName = '%s' to New " DEBUG fwLBSpillOverConfigure: Could not set POSTROUTING rules ERROR Dns proxy Restart failed DEBUG fwLBSpillOverConfigure: Something going wrong Here ERROR deleting interface to ifgroup failed DEBUG fwL2TPGenericRules.c: unable to open the database file " ERROR adding interface to ifgroup failed DEBUG fwL2TPGenericRules.c: inet_aton failed ERROR deleting interface pVirtIface %s from ifgroup %d" DEBUG fwPPTPGenericRules.c: unable to open the database file " ERROR adding interface pVirtIface %s to ifgroup %d failed DEBUG fwPPTPGenericRules.c: inet_aton failed ERROR Deleting IP address %s. DEBUG DNS proxy firewall rule add failed for %s ERROR Adding new IP address %s. DEBUG deleting interface %s from ifgroup %d failed ERROR Updating old IP address %s to new IP address %s. DEBUG adding interface %s to ifgroup %d failed ERROR Restarting Firewall For %s Address Update from %s:%s DEBUG nimfBridgeTblHandler: unable to get interfaceName ERROR Disabling Firewall Rule for MSS packet marking DEBUG nimfBridgeTblHandler: \ ERROR Enabling Firewall Rule for MSS packet marking DEBUG nimfBridgeTblHandler: unable to get \ ERROR Enabling packet marking rule for %s IDLE timer DEBUG Failed to %s traffic from %s to %s to IPS. ERROR Deleted firewall rule %s for service %s with action %s DEBUG Failed to %s traffic from %s to %s to IPS. ERROR %s firewall rule %s for service %s with action %s DEBUG failed to start IPS service. ERROR Added firewall rule %s for service %s with action %s DEBUG Timeout in waiting for IPS service to start. ERROR Deleting inbound(WAN-LAN) firewall rule. DEBUG Usage:%s <DBFile> <opType> <tblName> <rowId> " ERROR Deleting inbound(WAN-DMZ) firewall rule. DEBUG xlr8NatConfig: illegal invocation of (%s) ERROR RIPng disabled. DEBUG Illegal invocation of [%s] ERROR RIPng enabled. DEBUG xlr8NatMgmtTblHandler: failed query: %s ERROR Disable IPv6 firewall rule. DEBUG Could not open file: %s ERROR Enable IPv6 firewall rule. DEBUG Rip Error Command Too Long ERROR Deleting IGMP proxy rule. DEBUG No authentication for Ripv1 ERROR Enable IGMP proxy rule. DEBUG Invalid Rip Direction ERROR Restarting IGMP rule. DEBUG Invalid Rip Version ERROR Traffic meter enabled with no limit type. DEBUG Invalid Password for 1st Key ERROR Traffic meter enabled for only download. DEBUG Invalid Time for 1st Key ERROR Traffic meter enabled for both directions. DEBUG Invalid Password for 2nd Key ERROR Deleted firewall rule %s for service %s with action %s DEBUG Invalid Time for 2nd Key ERROR %s firewall rule %s for service %s with action %s DEBUG Invalid First KeyId ERROR Added firewall rule %s for service %s with action %s DEBUG Invalid Second KeyId ERROR Enabling Inter VLAN routing. DEBUG Invalid Authentication Type ERROR Updating inter VLAN routing status. DEBUG ripDisable failed ERROR Deleting inter VLAN routing. DEBUG ripEnable failed ERROR
Unified Services Router User Manual 182 Facility: Local0 (Wireless) Log Message Severity Log Message Severity (node=%s) setting %s to val = %d DEBUG sqlite3QueryResGet failed ERROR Custom wireless event: '%s' DEBUG sqlite3QueryResGet failed ERROR Wireless event: cmd=0x%x len=%d DEBUG VAP(%s) set beacon interval failed ERROR New Rogue AP (%02x:%02x:%02x:%02x:%02x:%02x) detected DEBUG VAP(%s) set DTIM interval failed ERROR WPS session in progress, ignoring enrolle assoc request DEBUG VAP(%s) set RTS Threshold failed ERROR ran query %s DEBUG VAP(%s) set Fragmentation Threshold failed ERROR DBUpdate event: Table: %s opCode:%d rowId:%d DEBUG VAP(%s) set Protection Mode failed ERROR %sing VAPs using profile %s DEBUG VAP(%s) set Tx Power failed ERROR %sing VAP %s DEBUG WDS Profile %s not found ERROR ran query %s DEBUG Failed to initalize WPS on %s ERROR %sing VAP instance %s DEBUG failed to get profile %s ERROR VAP(%s) set Short Preamble failed DEBUG could not initialize MGMT framework ERROR VAP(%s) set Short Retry failed DEBUG could not initialize MGMT framework ERROR VAP(%s) set Long Retry failed DEBUG dot11VapBssidUpdt SQL error: %s ERROR Decrypting context with key %s DEBUG sqlite3QueryResGet failed.Query:%s ERROR Unknown IAPP command %d received. DEBUG KDOT11_GET_PARAM(IEEE80211_IOC_CHANNEL) failed ERROR unexpected reply from %d cmd=%d ! DEBUG Failed to get the channel setting for %s ERROR unexpected reply from %d cmd=%d ! DEBUG sqlite3QueryResGet failed.Query:%s ERROR Recvied DOT11_EAPOL_KEYMSG DEBUG sqlite3QueryResGet failed.Query:%s ERROR shutting down AP:%s DEBUG profile %s not found ERROR APCtx Found DEBUG sqlite3QueryResGet failed.Query:%s ERROR APCtx Not-Found DEBUG Interface name and policy must be specified ERROR node not found *:*:*:%x:%x:%x DEBUG Interface name and policy must be specified ERROR error installing unicast key for %s DEBUG invalid ACL type %d ERROR cmd =%d i_type =%d i_val=%d DEBUG interface name not specified ERROR join event for new node %s DEBUG interface name not specified ERROR wpa/rsn IE id %d/%d not supported DEBUG Invalid interface - %s specified ERROR wpa IE id %d not supported DEBUG buffer length not specified ERROR leave event for node %s DEBUG Invalid length(%d) specified ERROR NodeFree request for node : %s DEBUG failed created iappdLock ERROR installing key to index %d DEBUG failed to create cipher contexts. ERROR iReq.i_val : %d DEBUG unable to register to UMI ERROR pIfName : %s DEBUG iappSockInit() failed ERROR iReq.i_val : %d DEBUG iappInit got error, unregistering it with UMI ERROR setting mode: %d DEBUG umiIoctl(UMI_COMP_UDOT11,%d,%d) failed ERROR Global counter wrapped, re-generating... DEBUG umiIoctl(UMI_COMP_KDOT11,%d,%d) failed ERROR
Unified Services Router User Manual 183 Got PNAC_EVENT_PREAUTH_SUCCESS event for : %s DEBUG UDP failed, received Length is %d ERROR event for non-existent node %s DEBUG umiIoctl(UMI_COMP_KDOT11, ERROR PNAC_EVENT_EAPOL_START event received DEBUG umiIoctl(UMI_COMP_UDOT11,%d,%d) \ ERROR PNAC_EVENT_EAPOL_LOGOFF event received DEBUG umiIoctl(UMI_COMP_KDOT11,%d,%d) \ ERROR PNAC_EVENT_REAUTH event received DEBUG No IAPP Node found for req id %d ERROR PNAC_EVENT_AUTH_SUCCESS event received DEBUG umiIoctl(UMI_COMP_UDOT11,%d,%d) \ ERROR PNAC_EVENT_PORT_STATUS_CHANGED event received DEBUG umiIoctl(UMI_COMP_KDOT11,%d,%d) \ ERROR unsupported event %d from PNAC DEBUG umiIoctl(UMI_COMP_UDOT11,%d,%d) failed ERROR event for non-existent node %s. Create new node. DEBUG UDP socket is not created ERROR Add new node to DOT11 Node list DEBUG UDP send failed ERROR Update dot11STA database DEBUG IAPP: socket (SOCK_STREAM) failed. ERROR Add PMKSA to the list DEBUG IAPP: TCP connect failed to %s. ERROR eapolRecvAuthKeyMsg: received key message DEBUG cmd %d not supported.sender=%d ERROR node not found DEBUG umiIoctl(UMI_COMP_KDOT11,%d,%d) failed ERROR eapolRecvKeyMsg: replay counter not incremented DEBUG IAPP-CACHE-NOTIFY-REQUEST send to ERROR eapolRecvKeyMsg: replay counter is not same DEBUG ./src/dot11/iapp/iappLib.c:1314: ADP_ERROR ( ERROR processing pairwise key message 2 DEBUG BSSID value passed is NULL ERROR RSN IE matching: OK DEBUG reserved requestId is passed ERROR processing pairwise key message 4 DEBUG interface name is NULL ERROR processing group key message 2 DEBUG IP address value passed is NULL ERROR processing key request message from client DEBUG opening receive UDP socket failed ERROR WPA version %2x %2x not supported DEBUG enabling broadcast for UDP socket failed ERROR (%s) group cipher %2x doesn't match DEBUG opening receive TCP socket for new AP failed ERROR (%s)Pairwise cipher %s not supported DEBUG ./src/dot11/iapp/iappLib.c:1784: ADP_ERROR( ERROR (%s) authentication method %d not supported DEBUG ./src/dot11/iapp/iappLib.c:1794: ADP_ERROR( ERROR %s:Auth method=%s pairwise cipher=%s IE size=%d DEBUG ./src/dot11/iapp/iappLib.c:1803: ADP_ERROR( ERROR WPA version %2x %2x not supported DEBUG failed created dot11dLock. ERROR Unable to obtain IE of type %d DEBUG failed initialize profile library. ERROR PTK state changed from %s to %s DEBUG failed to create cipher contexts. ERROR using PMKSA from cache DEBUG unable to register to UMI ERROR PTK GK state changed from %s to %s DEBUG could not create MIB tree ERROR GK state changed from %s to %s DEBUG unable to register to PNAC ERROR Sending PTK Msg1 DEBUG Max registration attempts by DOT11 to PNAC exceeded ERROR Sending PTK Msg3 DEBUG Creation of EAP WPS Profile Failed ERROR Sending GTK Msg1 DEBUG umiIoctl(UMI_COMP_IAPP,%d ) failed ERROR
Unified Services Router User Manual 184 sending EAPOL pdu to PNAC... DEBUG DOT11_RX_EAPOL_KEYMSG: unknown ifname %s ERROR creating pnac authenticator with values %d %d - %s DEBUG cmd %d not supported.sender=%d ERROR Profile %s does not exist DEBUG inteface name passed is NULL ERROR IAPP initialized. DEBUG BSSID passed is NULL ERROR Encrypting context key=%s for DEBUG inteface name passed is NULL ERROR could not find access point context for %s DEBUG unable to allocate memory for DOT11_CTX ERROR join event for existing node %s DEBUG unable to install wme mapping on %s ERROR failed to send PNAC_FORCE_AUTHORIZED " DEBUG unable to get %s mac address ERROR failed to send PNAC_AUTHORIZED " DEBUG Failed to set %s SSID ERROR failed to send PNAC_VAR_KEY_AVAILABLE (TRUE) " DEBUG Failed to set SSID broadcast status ERROR failed to send PNAC_VAR_KEY_TX_EN (TRUE) " DEBUG Failed to set PreAuth mode ERROR failed to send PNAC_VAR_KEY_TX_EN (FALSE) " DEBUG unable to install key ERROR failed to send PNAC_FORCE_AUTHORIZED " DEBUG KDOT11_SET_PARAM:IEEE80211_IOC_AUTHMODE failed ERROR failed to send PNAC_AUTHORIZED " DEBUG KDOT11_SET_PARAM:IEEE80211_IOC_PRIVACY failed ERROR mic verification: OK DEBUG wpaInit failed ERROR pnacIfConfig: Invalid supplicant" DEBUG dot11InstallProfile: unable to get interface index ERROR Failed to process user request DEBUG adpHmacInit(%s) failed ERROR Failed to process user request - %s(%d) DEBUG interface %s not found ERROR pnacIfConfigUmiIoctl: umiIoctl failed DEBUG AP not found on %s ERROR pnacIfConfigUmiIoctl: usrPnac returned %d DEBUG keyLen > PNAC_KEY_MAX_SIZE ERROR pnacIfConfigUmiIoctl: usrPnac returned %d DEBUG Invalid profile name passed ERROR pnacIfConfigUmiIoctl: usrPnac returned %d DEBUG Creation of WPS EAP Profile failed ERROR pnacKernNotifier: invalid PAE configuration " DEBUG unsupported command %d ERROR From pnacEapDemoAuthRecv: unsupported response " DEBUG device %s not found ERROR From pnacEapDemoAuthRecv: invalid codes received DEBUG unsupported command %d ERROR From pnacRadXlateDemoRecv: received unknown " DEBUG dot11NodeAlloc failed ERROR From pnacRadXlateDemoRecv: invalid codes received DEBUG Getting WPA IE failed for %s ERROR Error from pnacRadXlateDemoRecv: malloc failed DEBUG Getting WPS IE failed for %s ERROR From pnacRadXlateRadPktHandle: received a non-supported" DEBUG Failed initialize authenticator for node %s ERROR Only md5 authentication scheme currently supported. " DEBUG Failed to get the system up time while adding node %s ERROR Message from authenticator: DEBUG error creating PNAC port for node %s ERROR from pnacPDUXmit: bufsize = %d, pktType = %d," DEBUG dot11NodeAlloc failed ERROR pnacPDUXmit: sending eap packet. code = %d, " DEBUG Invalid arguments. ERROR
Unified Services Router User Manual 185 pnacRecvRtn: no corresponding pnac port pae found DEBUG umiIoctl(UMI_COMP_IAPP,%d) failed ERROR sending unicast key DEBUG Invalid IE. ERROR sending broadcast key DEBUG umiIoctl(UMI_COMP_KDOT11_VAP,%d ) failed ERROR from pnacAuthPAEDisconnected: calling pnacTxCannedFail DEBUG umiIoctl(UMI_COMP_KDOT11,%d ,%d) failed ERROR from pnacAuthPAEForceUnauth: calling pnacTxCannedFail DEBUG KDOT11_SET_PARAM:IEEE80211_IOC_WME_CWMIN failed ERROR state changed from %s to %s DEBUG KDOT11_SET_PARAM:IEEE80211_IOC_WME_CWMAX failed ERROR PNAC user comp id not set. dropping event %d DEBUG KDOT11_SET_PARAM:IEEE80211_IOC_WME_AIFS failed ERROR sending event %d to %d DEBUG KDOT11_SET_PARAM:80211_IOC_WME_TXOPLIMIT failed ERROR requesting keys informantion from %d DEBUG KDOT11_SET_PARAM:IEEE80211_IOC_WME_ACM failed ERROR pnacUmiPortPaeParamSet: error in getting port pae DEBUG KDOT11_SET_PARAM:IEEE80211_IOC_WME failed ERROR pnacUmiPortPaeParamSet: invalid param - %d DEBUG invalid group cipher %d ERROR pnacRecvASInfoMessage: Skey of length %d set DEBUG KDOT11_SET_PARAM:IEEE80211_IOC_MCASTCIPHER failed ERROR pnacRecvASInfoMessage: reAuthPeriod set to: %d DEBUG KDOT11_SET_PARAM:IEEE80211_IOC_MCASTKEYLEN failed ERROR pnacRecvASInfoMessage: suppTimeout set to: %d DEBUG KDOT11_SET_PARAM:IEEE80211_IOC_UCASTCIPHERS failed ERROR PORT SUCCESSFULLY DESTROYED DEBUG KDOT11_SET_PARAM:IEEE80211_IOC_KEYMGTALGS failed ERROR creating physical port for %s DEBUG KDOT11_SET_PARAM:IEEE80211_IOC_WPA failed ERROR pnacAuthInit: using defualt pnacAuthParams DEBUG unknow cipher type = %d ERROR pnacSuppInit: using defualt pnacSuppParams DEBUG umiIoctl(UMI_COMP_IAPP,%d) failed ERROR Error from pnacCombinedStMachTriggerFunc: " DEBUG invalid media value=%d ERROR Error from pnacCombinedStMachTriggerFunc: " DEBUG invalid mediaOpt value=%d ERROR Error from pnacCombinedStMachTriggerFunc: " DEBUG invalid mode value=%d ERROR Error from pnacCombinedStMachTriggerFunc: " DEBUG dot11PnacIfCreate failed ERROR Error from pnacCombinedStMachTriggerFunc: " DEBUG wpaPRF failed ERROR Error from pnacCombinedStMachTriggerFunc: " DEBUG Error generating global key counter ERROR Error from pnacCombinedStMachTriggerFunc: " DEBUG wpaCalcMic: unsupported key descriptor version ERROR Error from pnacCombinedStMachTriggerFunc: " DEBUG integrity failed. need to stop all stations " ERROR Error from pnacCombinedStMachTriggerFunc: " DEBUG couldn't find AP context for %s interface ERROR received a pdu on %s DEBUG dot11Malloc failed ERROR pnacRecvMapi: protoType: %04x pPhyPort->authToASSendRtn:%p DEBUG dot11Malloc failed ERROR port not found DEBUG eapolRecvKeyMsg: unknown descType =%d ERROR
Unified Services Router User Manual 186 from pnacRecvMapi: pkt body len = %d, pktType = %d DEBUG eapolRecvKeyMsg: invalid descriptor version ERROR from pnacPDUProcess: received PNAC_EAP_PACKET DEBUG eapolRecvKeyMsg: incorrect descriptor version ERROR from pnacPDUProcess: currentId = %d DEBUG eapolRecvKeyMsg: Ack must not be set ERROR from pnacPDUProcess: code = %d, identifier = %d, " DEBUG eapolRecvKeyMsg: MIC bit must be set ERROR from pnacPDUProcess: setting rxResp true DEBUG wpaAuthRecvPTKMsg2: unexpected packet received ERROR from pnacPDUProcess: code = %d, identifier = %d, " DEBUG wpaAuthRecvPTKMsg2: mic check failed ERROR from pnacPDUProcess: received " DEBUG wpaAuthRecvPTKMsg2: rsn ie mismatch ERROR from pnacPDUProcess: received " DEBUG wpaAuthRecvPTKMsg4: unexpected packet received ERROR from pnacPDUProcess: received PNAC_EAPOL_KEY_PACKET DEBUG wpaAuthRecvPTKMsg4: keyDataLength not zero ERROR doing pnacTxCannedFail DEBUG wpaAuthRecvPTKMsg4: mic check failed ERROR doing pnacTxCannedSuccess DEBUG wpaAuthRecvGTKMsg2: unexpected packet received ERROR doing pnacTxReqId DEBUG secureBit not set in GTK Msg2 ERROR doing pnacTxReq DEBUG wpaAuthRecvGTKMsg2: keyDataLength not zero ERROR doing pnacTxStart DEBUG wpaAuthRecvGTKMsg2: mic check failed ERROR doing pnacTxLogoff DEBUG wpaAuthRecvKeyReq: unexpected packet received ERROR doing pnacTxRspId: 1st cond DEBUG wpaAuthRecvKeyReq: keyDataLength not zero ERROR doing pnacTxRspId: entering 2nd cond DEBUG wpaAuthRecvKeyReq: mic check failed ERROR from pnacTxRspId: code = %d, identifier = %d, length = %d, " DEBUG invalid OUI %x %x %x ERROR doing pnacTxRspId: 2nd cond DEBUG (%s) invalid OUI %x %x %x ERROR doing pnacTxRspAuth: 1st cond DEBUG [%s:%d] Cipher in WPA IE : %x ERROR doing pnacTxRspAuth: 2nd cond DEBUG (%s) invalid OUI %x %x %x ERROR message for unknown port PAE DEBUG short WPA IE (length = %d) received ERROR from pnacACToSuppRecvRtn: calling pnacEapPktRecord DEBUG PTK state machine in unknown state. ERROR from pnacEapPktRecord: code = %d, identifier = %d, " DEBUG dot11InstallKeys failed ERROR from pnacEapPktRecord: received success pkt DEBUG group state machine entered into WPA_AUTH_GTK_INIT ERROR from pnacEapPktRecord: received failure pkt DEBUG dot11Malloc failed ERROR from pnacEapPktRecord: received request pkt DEBUG dot11Malloc failed ERROR unknown EAP-code %d DEBUG dot11Malloc failed ERROR Authenticator[%d]: DEBUG aesWrap failed ERROR Auth PAE state = %s DEBUG unknown key descriptor version %d ERROR Auth Reauth state = %s DEBUG dot11Malloc failed ERROR Back auth state = %s DEBUG could not initialize AES128ECB ERROR Supplicant[%d]: DEBUG could not initialize AES-128-ECB ERROR Supp Pae state = %s DEBUG MD5 initialization failed ERROR
Unified Services Router User Manual 187 from pnacBackAuthFail: calling pnacTxCannedFail DEBUG RC4 framework initialization failed ERROR %s returned ERROR DEBUG PNAC framework initialization failed ERROR pnacUmiIoctlHandler: cmd: %s(%d) DEBUG ERROR: option value not specified ERROR %s not configured for 802.1x DEBUG ERROR: -u can be used only with -s ERROR could not process PDU received from the wire DEBUG ERROR: user-name not specified ERROR pnacPDUForward: failed to foward the received PDU DEBUG failed to enable debug ERROR Creating PHY port with AUTH backend : %s SendRtn: %p RecvRtn:%p DEBUG [%s]: failed to convert string to MAC " ERROR pnacUmiAuthConfig: %s not configured for 802.1x DEBUG failed to initialize UMI ERROR pnacSuppRegisterUserInfo: not a valid AC DEBUG pnacPhyPortParamSet:invalid arguments ERROR pnacIfConfig: autoAuth Enabled DEBUG pnacPhyPortParamSet:Failed to create socket ERROR pnacSendRtn: no pnac port pae found for " DEBUG Error from pnacPhyPortParamSet:%s-device invalid ERROR sending portStatus: %s[%d] to dot11 DEBUG Error from pnacPhyPortParamSet:%s-Getting MAC address " ERROR pnacRecvASInfoMessage: Rkey of length %d set DEBUG pnacPhyPortParamSet:Failed to add 802.1X multicast " ERROR ASSendRtn: %p ASToAuthRecv: %p DEBUG pnacIsInterfaceUp: failed to create a raw socket ERROR adpRand failed:unable to generate random unicast key WARN pnacIsInterfaceUp: failed to get interface flags ERROR using group key as unicast key WARN failed to allocate buffer ERROR Integrity check failed more than once in last 60 secs. WARN UMI initialization failed ERROR MIC failed twice in last 60 secs, taking countermeasures WARN UMI initialization failed ERROR Failed to set dot11 port status WARN Error from pnacEapDemoAuthLibInit: malloc failed ERROR PTK state machine in NO_STATE. WARN Error from pnacEapDemoAuthRecv: received null EAP pkt ERROR PTK state machine in NO_STATE!! WARN Error from pnacEapDemoAuthRecv: send " ERROR PMKSA refcount not 1 WARN Error from pnacRadXlateASAdd: cannot open socket ERROR IV verification failednknown subtype> WARN Error from pnacRadXlateDemoRecv: received null EAP pkt ERROR pnacIfConfig: overwriting previous interface " WARN From pnacRadXlateDemoRecv: send " ERROR pnacIfConfig: overwriting previous " WARN Error from pnacRadXlateDemoRecv: radius " ERROR pnacIfConfig: overwriting previous username" WARN Error from pnacRadXlateDemoRecv: radius " ERROR pnacIfConfig: overwriting previous password" WARN Error from pnacRadXlateRadIdRespSend: send to failed ERROR %s: Failed to set port status WARN Error from pnacRadXlateRadNonIdRespSend: send to failed ERROR %s: Failed to notify event to dot11 WARN Error from pnacRadXlateRadRecvProc: recvfrom failed ERROR pnacLibDeinit: Failed to destroy the WARN From ERROR
Unified Services Router User Manual 188 phyPort:%s pnacRadXlateRadPktIntegrityChk: no corresponding " pnacPortPaeDeconfig:kpnacPortPaeDeconfig failed WARN Error from pnacRadXlateRadPktIntegrityChk: no message " ERROR pnacPortPaeDeconfig:kpnacPortPaeDeconfig failed WARN Error from pnacRadXlateRadPktIntegrityChk: " ERROR pnacBackAuthSuccess: failed to notify the destination " WARN From pnacRadXlateRadChalPktHandle: no encapsulated eap " ERROR could not initialize MGMT framework ERROR Error from pnacRadXlateRadChalPktHandle: malloc for eap " ERROR umiInit failed ERROR Error from pnacEapDemoSuppUserInfoRegister: invalid " ERROR iappInit failed ERROR Error from pnacEapDemoSuppRecv: received null EAP pkt ERROR could not initialize IAPP MGMT. ERROR Error from pnacEapDemoSuppRecv: send ptr to pnac supplicant" ERROR dot11Malloc failed ERROR From pnacEapDemoSuppRecv: user info not entered yet ERROR buffer length not specified ERROR Error from pnacEapDemoSuppRecv: couldn't " ERROR Invalid length(%d) specified ERROR MDString: adpDigestInit for md5 failed ERROR Failed to get information about authorized AP list. ERROR pnacUmiInit: UMI initialization failed ERROR Recd IE data for non-existent AP %s ERROR could not start PNAC task ERROR Recd IE data for wrong AP %s ERROR invalid aruments ERROR Received Invalid IE data from WSC ERROR pnacIfNameToIndex failed ERROR Recd IE data for non-existent AP %s ERROR pnacPhyPortParamSet: device invalid %s%d ERROR Recd WSC Start command without interface name ERROR pnacPhyPortParamSet: EIOCGADDR ioctl failed ERROR Recd WSC start for non-existent AP %s ERROR pnacPhyPortParamSet: multicast addr add ioctl failed ERROR Recd WSC start for wrong AP %s ERROR pnacPhyPortParamUnset: multicast addr del ioctl failed ERROR Unable to send WSC_WLAN_CMD_PORT to WSC ERROR pnacPDUXmit: Invalid arguments ERROR Failed to get the ap context for %s ERROR pnacPDUXmit: failed to get M_BLK_ID ERROR WPS can only be applied to WPA/WPA2 security profiles ERROR from pnacIsInterfaceUp: device %s%d invalid ERROR wpsEnable: running wsccmd failed ERROR pnacRecvRtn: dropping received packet as port is" ERROR Failed to get the ap context for %s ERROR pnacSendRtn: Invalid arguments ERROR WPS conf. under non WPA/WPA2 security setting ERROR pnacSendRtn: no physical port corresponding to" ERROR Failed to reset the Beacon Frame IE in the driver ERROR pnacSendRtn: dropping packet as port" ERROR Failed to reset the Beacon Frame IE in the driver ERROR pnacAuthBuildRC4KeyDesc: adpEncryptInit(RC4) failed ERROR WPS method cannot be NULL ERROR pnacAuthBuildRC4KeyDesc: adpCipherContextCtrl" ERROR PIN value length should be a multiple of 4 !! ERROR pnacDot11UserSet: incorrect buffer length ERROR Failed to initiate PIN based association, PIN = %s ERROR PNAC user component id not set. ERROR
Unified Services Router User Manual 189 Failed to initiate PBC based enrolle association ERROR pnacKeyInfoGet:failed to allocate buffer ERROR Invalid association mode. (Allowed modes : PIN/PBC) ERROR PNAC user comp id not set. dropping EAPOL key pkt ERROR wpsEnable: running wsccmd failed ERROR pnacUmiPortPaeParamSet: invalid buffer received ERROR Failed to send QUIT command to WSC from DOT11 ERROR Error from pnacRecvASInfoMessage: " ERROR Failed to clear off the WPS process ERROR pnacRecvASInfoMessage: " ERROR missing profile name ERROR pnacRecvASInfoMessage: Bad info length ERROR A profile exists with the same name ERROR Error from pnacLibInit: malloc failed ERROR Error in allocating memory for profile ERROR could not create phy ports lock ERROR missing profile name ERROR could not create nodes ports lock ERROR missing profile name ERROR port exists for iface - %s ERROR Profile name and interface name must be specified ERROR pnacPhyPortCreate failed ERROR Profile %s does not exist ERROR kpnacPhyPortCreate failed ERROR Could not set profile %s on the interface %s ERROR invalid argument ERROR missing profile name ERROR pnacAuthConfig: maxAuth limit reached ERROR Profile %s does not exist ERROR pnacAuthConfig: malloc failed ERROR Profile %s does not exist ERROR Error from pnacAuthConfig: pAsArg cannot be NULL ERROR SSID should not be longer than %d ERROR Error from pnacAuthConfig: receive routine hook " ERROR Profile %s does not exist ERROR pnacAuthConfig: pnacAuthInit failed ERROR Profile %s does not exist ERROR kpnacPortPaeConfig failed ERROR Profile %s does not exist ERROR Invalid arguments ERROR Profile %s does not exist ERROR Error from pnacSuppConfig: malloc failed ERROR Profile %s does not exist ERROR Error from pnacSuppConfig: receive routine hook " ERROR Profile %s does not exist ERROR Error from pnacSuppConfig: pnacSuppInit failed ERROR SSID not set. SSID is needed to generate password hash ERROR kpnacPortPaeConfig failed ERROR Password string too big ERROR pnacAuthDeconfig failed: pPortPae NULL ERROR dot11Malloc failed ERROR Error from pnacPhyPortDestroy: port not configured ERROR Profile %s does not exist ERROR pnacPhyPortDestroy: Failed to deconfigure port ERROR Hex string should only have %d hex chars ERROR pnacPhyPortParamUnset FAILED ERROR dot11Malloc failed ERROR Error from pnacPhyPortCreate: malloc failed ERROR Profile %s does not exist ERROR Error from pnacPhyPortCreate: pnacPhyPortParamSet" ERROR invalid key index %d. key index should be 0-3. ERROR error from pnacPhyPortCreate: malloc failed ERROR wepKey length incorrect ERROR Error from pnacAuthInit: pnacPortTimersInit failed ERROR Profile %s does not exist ERROR Error from pnacAuthInit: pnacAuthPAEInit failed ERROR
Unified Services Router User Manual 190 Invalid Cipher type %d ERROR Error from pnacAuthInit: pnacAuthKeyTxInit failed ERROR Profile supports WEP stas,Group cipher must be WEP ERROR Error from pnacAuthInit: pnacReauthTimerInit failed ERROR Profile %s does not exist ERROR Error from pnacAuthInit: pnacBackAuthInit failed ERROR Profile %s does not exist ERROR Error from pnacAuthInit: pnacCtrlDirInit failed ERROR Profile %s does not exist ERROR Error from pnacAuthInit: pnacKeyRecvInit failed ERROR invalid pairwise cipher type %d ERROR Error from pnacSuppInit: malloc failed ERROR Cipher %s is already in the list. ERROR Error from pnacSuppInit: pnacPortTimersInit failed ERROR Profile %s does not exist ERROR Error from pnacSuppInit: pnacKeyRecvInit failed ERROR Invalid Cipher type %d ERROR Error from pnacSuppInit: pnacSuppKeyTxInit failed ERROR Cipher %s not found in the list. ERROR Error from pnacSuppInit: pnacSuppPAEInit failed ERROR Profile %s does not exist ERROR Error from pnacRecvRtn: invalid arguments ERROR Profile %s does not exist ERROR Error from pnacRecvMapi: unsupported PDU received ERROR Auth method %s is already in the list ERROR suppToACSendRtn returned not OK! ERROR Profile %s does not exist ERROR Error from pnacBasicPktCreate: malloc failed ERROR Auth method %s not found in the list. ERROR Error from pnacEAPPktCreate: basic pkt create failed ERROR Profile %s does not exist ERROR Error from pnacTxCannedFail: eap pkt create failed ERROR Profile %s does not exist ERROR Error from pnacTxCannedSuccess: eap pkt create failed ERROR Profile %s does not exist ERROR Error from pnacTxReqId: eap pkt create failed ERROR invalid type value %d. supported values are 1,2,3,4 ERROR Error from pnacTxReq: eap pkt create failed ERROR Profile %s does not exist ERROR Error from pnacSendRespToServer: malloc failed ERROR invalid type value %d. supported values are 1,2,3,4 ERROR Error from pnacSendRespToServer: no AS configured ERROR Profile %s does not exist ERROR Error from pnacTxStart: basic pkt create failed ERROR invalid type value %d. supported values are 1,2,3,4 ERROR Error from pnacTxStart: basic pkt create failed ERROR Profile %s does not exist ERROR Error from pnacTxRspId: eap pkt create failed ERROR invalid type value %d. supported values are 1,2,3,4 ERROR Error from pnacTxRspAuth: eap pkt create failed ERROR Profile %s does not exist ERROR Error from pnacEapPktRecord: EAP packet too" ERROR invalid type value %d. supported values are 1,2,3,4 ERROR Error from pnacEapPktRecord: " ERROR Profile %s does not exist ERROR from pnacBackAuthTimeout: calling pnacTxCannedFail ERROR ERROR: incomplete DB update information. ERROR hmac_md5: adpHmacContextCreate failed ERROR old values result does not contain 2 rows ERROR hmac_md5:adpHmacInit failed ERROR sqlite3QueryResGet failed ERROR pnacUmiIoctlHandler: invalid cmd: %d ERROR
Unified Services Router User Manual 191 Error in executing DB update handler ERROR pnacEapRadAuthSend: Invalid arguments ERROR sqlite3QueryResGet failed ERROR pnacEapRadAuthSend: failed to allocate inbuffer ERROR ERROR: incomplete DB update information. ERROR pnacXmit : umiIoctl failed[%d] ERROR old values result does not contain 2 rows ERROR pnacPDUForward: Invalid input ERROR sqlite3QueryResGet failed ERROR pnacPDUForward: error in getting port pae information ERROR Error in executing DB update handler ERROR pnacPDUForward: error allocating memory ERROR sqlite3QueryResGet failed.Query:%s ERROR pnacUmiIfMacAddrChange: %s not configured for 802.1x ERROR sqlite3QueryResGet failed.Query:%s ERROR pnacUmiIfMacAddrChange: could not process PDU received" ERROR sqlite3QueryResGet failed.Query:%s ERROR pnacUmiPhyPortConfig: Invalid config data ERROR sqlite3QueryResGet failed.Query:%s ERROR pnacUmiPhyPortConfig: Invalid backend name specified ERROR startStopVap failed to stop %s ERROR pnacUmiPhyPortConfig: could not create PNAC physical" ERROR Invalid SQLITE operation code - %d ERROR pnacUmiAuthConfig: Invalid config data ERROR ./src/dot11/mgmt/dot11Mgmt.c:1177: ADP_ERROR ( ERROR pnacUmiAuthConfig: Invalid backend name specified ERROR only delete event expected on dot11RogueAP. ERROR unable to create new EAP context. ERROR sqlite3QueryResGet failed ERROR unable to apply %s profile on the EAP context. ERROR unhandled database operation %d ERROR pnacUmiAuthConfig: could not configure PNAC PAE " ERROR sqlite3QueryResGet failed ERROR pnacUmiSuppConfig: Invalid config data ERROR failed to configure WPS on %s ERROR pnacUmiSuppConfig: Invalid backend name specified ERROR sqlite3QueryResGet failed ERROR pnacUmiSuppConfig: %s not configured for 802.1x ERROR sqlite3QueryResGet failed ERROR pnacUmiSuppConfig: could not PNAC port Access" ERROR sqlite3QueryResGet failed ERROR pnacUmiSuppConfig: Failed to register user information ERROR sqlite3QueryResGet failed ERROR pnacPortByMacDeconfig: port not found ERROR sqlite3QueryResGet failed ERROR pnacPortByMacDeconfig: port not found ERROR no VAP rows returned. expected one ERROR pnacUmiIfDown: Invalid config data ERROR multiple VAP rows returned. expected one ERROR pnacUmiIfDown: Invalid config data ERROR sqlite3QueryResGet failed ERROR Error from pnacPortDeconfig: port not configured ERROR invalid query result. ncols=%d nrows=%d ERROR pnacUmiIfDown: could not de-configure port ERROR %s:VAP(%s) create failed ERROR pnacUmiPhyPortDestroy: Invalid config data ERROR sqlite3QueryResGet failed ERROR pnacUmiPhyPortDestroy: Invalid config data ERROR invalid query result. ncols=%d nrows=%d ERROR pnacUmiPhyPortDestroy: Failed to destroy the port ERROR
Unified Services Router User Manual 192 Invalid config data ERROR Facility: Kernel Log Message Severity Log Message Severity DNAT: multiple ranges no longer supported DEBUG %s: %s%s:%d -> %s:%d %s, DEBUG DNAT: Target size %u wrong for %u ranges, DEBUG %s: %s%s:%d %s, DEBUG DNAT: wrong table %s, tablename DEBUG %s: Failed to add WDS MAC: %s, dev->name, DEBUG DNAT: hook mask 0x%x bad, hook_mask DEBUG %s: Device already has WDS mac address attached, DEBUG %s%d: resetting MPPC/MPPE compressor, DEBUG %s: Added WDS MAC: %s, dev->name, DEBUG %s%d: wrong offset value: %d, DEBUG %s: WDS MAC address %s is not known by this interface, DEBUG %s%d: wrong length of match value: %d, DEBUG [madwifi] %s() : Not enough space., __FUNCTION__ DEBUG %s%d: too big offset value: %d, DEBUG Returning to chan %d, ieeeChan DEBUG %s%d: cannot decode offset value, DEBUG WEP DEBUG %s%d: wrong length code: 0x%X, DEBUG AES DEBUG %s%d: short packet (len=%d), __FUNCTION__, DEBUG AES_CCM DEBUG %s%d: bad sequence number: %d, expected: %d, DEBUG CKIP DEBUG %s%d: bad sequence number: %d, expected: %d, DEBUG TKIP DEBUG PPPIOCDETACH file->f_count=%d, DEBUG %s: cannot map channel to mode; freq %u flags 0x%x, DEBUG PPP: outbound frame not passed DEBUG %s: %s, vap->iv_dev->name, buf DEBUG PPP: VJ decompression error DEBUG %s: [%s] %s, vap->iv_dev->name, DEBUG PPP: inbound frame not passed DEBUG %s: [%s] %s, vap->iv_dev->name, ether_sprintf(mac), buf DEBUG PPP: reconstructed packet DEBUG [%s:%s] discard %s frame, %s, vap->iv_dev->name, DEBUG PPP: no memory for DEBUG [%s:%s] discard frame, %s, vap->iv_dev->name, DEBUG missed pkts %u..%u, DEBUG [%s:%s] discard %s information element, %s, DEBUG %s%d: resetting MPPC/MPPE compressor, DEBUG [%s:%s] discard information element, %s, DEBUG %s%d: wrong offset value: %d, DEBUG [%s:%s] discard %s frame, %s, vap->iv_dev->name, DEBUG %s%d: wrong length of match value: %d, DEBUG [%s:%s] discard frame, %s, vap->iv_dev->name, DEBUG %s%d: too big offset value: %d, DEBUG ifmedia_add: null ifm DEBUG %s%d: cannot decode offset value, DEBUG Adding entry for DEBUG %s%d: wrong length code: 0x%X, DEBUG ifmedia_set: no match for 0x%x/0x%x, DEBUG %s%d: short packet (len=%d), __FUNCTION__, DEBUG ifmedia_set: target DEBUG %s%d: bad sequence number: %d, expected: %d, DEBUG ifmedia_set: setting to DEBUG
Unified Services Router User Manual 193 %s%d: bad sequence number: %d, expected: %d, DEBUG ifmedia_ioctl: no media found for 0x%x, DEBUG PPPIOCDETACH file->f_count=%d, DEBUG ifmedia_ioctl: switching %s to , dev->name DEBUG PPP: outbound frame not passed DEBUG ifmedia_match: multiple match for DEBUG PPP: VJ decompression error DEBUG <unknown type> DEBUG PPP: inbound frame not passed DEBUG desc->ifmt_string DEBUG PPP: reconstructed packet DEBUG mode %s, desc->ifmt_string DEBUG PPP: no memory for DEBUG <unknown subtype> DEBUG missed pkts %u..%u, DEBUG %s, desc->ifmt_string DEBUG %s: INC_USE_COUNT, now %d, __FUNCTION__, mod_use_count \ DEBUG %s%s, seen_option++ ? , : , DEBUG %s: DEC_USE_COUNT, now %d, __FUNCTION__, mod_use_count \ DEBUG %s%s, seen_option++ ? , : , DEBUG PPPOL2TP %s: _fmt, DEBUG %s, seen_option ? > : DEBUG PPPOL2TP: --> %s, __FUNCTION__) DEBUG %s: %s, dev->name, buf DEBUG PPPOL2TP: <-- %s, __FUNCTION__) DEBUG %s: no memory for sysctl table!, __func__ DEBUG %s: recv: , tunnel->name DEBUG %s: no memory for VAP name!, __func__ DEBUG %s: xmit:, session->name DEBUG %s: failed to register sysctls!, vap->iv_dev->name DEBUG %s: xmit:, session->name DEBUG %s: no memory for new proc entry (%s)!, __func__, DEBUG %s: module use_count is %d, __FUNCTION__, mod_use_count DEBUG %s: 0x%p len %u, tag, p, len DEBUG PPPOL2TP %s: _fmt, DEBUG %03d:, i DEBUG PPPOL2TP: --> %s, __FUNCTION__) DEBUG %02x, ((u_int8_t *)p)[i] DEBUG PPPOL2TP: <-- %s, __FUNCTION__) DEBUG first difference at byte %u, i DEBUG %s: recv: , tunnel->name DEBUG %s: , t->name DEBUG %s: xmit:, session->name DEBUG FAIL: ieee80211_crypto_newkey failed DEBUG %s: xmit:, session->name DEBUG FAIL: ieee80211_crypto_setkey failed DEBUG PPPOL2TP %s: _fmt, DEBUG FAIL: unable to allocate skbuff DEBUG PPPOL2TP: --> %s, __FUNCTION__) DEBUG FAIL: wep decap failed DEBUG PPPOL2TP: <-- %s, __FUNCTION__) DEBUG FAIL: decap botch; length mismatch DEBUG %s: recv: , tunnel->name DEBUG FAIL: decap botch; data does not compare DEBUG %s: xmit:, session->name DEBUG FAIL: wep encap failed DEBUG %s: xmit:, session->name DEBUG FAIL: encap data length mismatch DEBUG IRQ 31 is triggered DEBUG FAIL: encrypt data does not compare DEBUG [%s:%d] , __func__, __LINE__\ DEBUG PASS DEBUG \t[R%s %#0x %#0x 0x%08x%08x], (status == ERROR ? # : ), page, addr, (uint32_t)(*pValue >> 32), (uint32_t)(*pValue & 0xffffffff) DEBUG %u of %u 802.11i WEP test vectors passed, pass, total DEBUG \t[W%s %#0x %#0x 0x%08x%08x], (status == ERROR ? # : ), page, addr, (uint32_t)(value >> 32), (uint32_t)(value & 0xffffffff) DEBUG %s: 0x%p len %u, tag, p, len DEBUG %s: mac_add %02X:%02X:%02X:%02X:%02X:%02X, dev->name, addr[0], addr[1], addr[2], addr[3], addr[4], addr[5] DEBUG %03d:, i DEBUG
Unified Services Router User Manual 194 %s: mac_del %02X:%02X:%02X:%02X:%02X:%02X, dev->name, addr[0], addr[1], addr[2], addr[3], addr[4], addr[5] DEBUG %02x, ((u_int8_t *)p)[i] DEBUG %s: mac_kick %02X:%02X:%02X:%02X:%02X:%02X, dev->name, addr[0], addr[1], addr[2], addr[3], addr[4], addr[5] DEBUG first difference at byte %u, i DEBUG %s: mac_undefined %02X:%02X:%02X:%02X:%02X:%02X, dev->name, addr[0], addr[1], addr[2], addr[3], addr[4], addr[5] DEBUG %s: , t->name DEBUG %s: addr_add %02X:%02X:%02X:%02X:%02X:%02X, dev->name, addr[0], addr[1], addr[2], addr[3], addr[4], addr[5] DEBUG FAIL: ieee80211_crypto_newkey failed DEBUG %s: addr_del %02X:%02X:%02X:%02X:%02X:%02X, dev->name, addr[0], addr[1], addr[2], addr[3], addr[4], addr[5] DEBUG FAIL: ieee80211_crypto_setkey failed DEBUG %s: mac_undefined %02X:%02X:%02X:%02X:%02X:%02X, dev->name, addr[0], addr[1], addr[2], addr[3], addr[4], addr[5] DEBUG FAIL: unable to allocate skbuff DEBUG %s: set_float %d;%d, DEBUG FAIL: ccmp encap failed DEBUG IRQ 32 is triggered DEBUG FAIL: encap data length mismatch DEBUG ip_finish_output2: No header cache and no neighbour! DEBUG FAIL: encrypt data does not compare DEBUG a guy asks for address mask. Who is it? DEBUG FAIL: ccmp decap failed DEBUG icmp v4 hw csum failure) DEBUG FAIL: decap botch; length mismatch DEBUG expire>> %u %d %d %d, expire, DEBUG FAIL: decap botch; data does not compare DEBUG expire++ %u %d %d %d, expire, DEBUG PASS DEBUG rt_cache @%02x: %u.%u.%u.%u, hash, DEBUG %u of %u 802.11i AES-CCMP test vectors passed, pass, total DEBUG rt_bind_peer(0) @%p, NET_CALLER(iph) DEBUG %s: 0x%p len %u, tag, p, len DEBUG ip_rt_advice: redirect to DEBUG %03d:, i DEBUG ip_rt_bug: %u.%u.%u.%u -> %u.%u.%u.%u, %s, DEBUG %02x, ((u_int8_t *)p)[i] DEBUG udp cork app bug 2) DEBUG first difference at byte %u, i DEBUG udp cork app bug 3) DEBUG ieee80211_crypto_newkey failed DEBUG udp v4 hw csum failure.) DEBUG ieee80211_crypto_setkey failed DEBUG UDP: short packet: From %u.%u.%u.%u:%u %d/%d to %u.%u.%u.%u:%u, DEBUG unable to allocate skbuff DEBUG UDP: bad checksum. From %d.%d.%d.%d:%d to %d.%d.%d.%d:%d ulen %d, DEBUG tkip enmic failed DEBUG %s: lookup policy [list] found=%s, DEBUG enmic botch; length mismatch DEBUG %s: called: [output START], __FUNCTION__ DEBUG enmic botch DEBUG %s: flow dst=%s, __FUNCTION__, XFRMSTRADDR(fl->fl4_dst, family) DEBUG tkip encap failed DEBUG %s: flow src=%s, __FUNCTION__, XFRMSTRADDR(fl->fl4_src, family) DEBUG encrypt phase1 botch DEBUG
Unified Services Router User Manual 195 %s: flow dst=%s, __FUNCTION__, XFRMSTRADDR(fl->fl6_dst, family) DEBUG encrypt data length mismatch DEBUG %s: flow src=%s, __FUNCTION__, XFRMSTRADDR(fl->fl6_src, family) DEBUG encrypt data does not compare DEBUG a guy asks for address mask. Who is it? DEBUG tkip decap failed DEBUG icmp v4 hw csum failure) DEBUG decrypt phase1 botch DEBUG expire>> %u %d %d %d, expire, DEBUG decrypt data does not compare DEBUG expire++ %u %d %d %d, expire, DEBUG decap botch; length mismatch DEBUG rt_cache @%02x: %u.%u.%u.%u, hash, DEBUG decap botch; data does not compare DEBUG rt_bind_peer(0) @%p, NET_CALLER(iph) DEBUG tkip demic failed DEBUG ip_rt_advice: redirect to DEBUG 802.11i TKIP test vectors passed DEBUG ip_rt_bug: %u.%u.%u.%u -> %u.%u.%u.%u, %s, DEBUG %s, buf DEBUG UDP: short packet: From %u.%u.%u.%u:%u %d/%d to %u.%u.%u.%u:%u, DEBUG Atheros HAL assertion failure: %s: line %u: %s, DEBUG UDP: bad checksum. From %d.%d.%d.%d:%d to %d.%d.%d.%d:%d ulen %d, DEBUG ath_hal: logging to %s %s, ath_hal_logfile, DEBUG a guy asks for address mask. Who is it? DEBUG ath_hal: logging disabled DEBUG fib_add_ifaddr: bug: prim == NULL DEBUG %s%s, sep, ath_hal_buildopts[i] DEBUG fib_del_ifaddr: bug: prim == NULL DEBUG ath_pci: No devices found, driver not installed. DEBUG expire>> %u %d %d %d, expire, DEBUG _fmt, __VA_ARGS__ DEBUG expire++ %u %d %d %d, expire, DEBUG %s: Warning, using only %u entries in %u key cache, DEBUG rt_cache @%02x: %u.%u.%u.%u, hash, DEBUG %s: TX99 support enabled, dev->name DEBUG rt_bind_peer(0) @%p, DEBUG %s:grppoll Buf allocation failed ,__func__ DEBUG ip_rt_advice: redirect to DEBUG %s: %s: unable to start recv logic, DEBUG ip_rt_bug: %u.%u.%u.%u -> %u.%u.%u.%u, %s, DEBUG %s: %s: unable to start recv logic, DEBUG %s: lookup policy [list] found=%s, DEBUG %s: no skbuff, __func__ DEBUG %s: called: [output START], __FUNCTION__ DEBUG %s: hardware error; resetting, dev->name DEBUG %s: flow dst=%s, __FUNCTION__, XFRMSTRADDR(fl->fl4_dst, family) DEBUG %s: rx FIFO overrun; resetting, dev->name DEBUG %s: flow src=%s, __FUNCTION__, XFRMSTRADDR(fl->fl4_src, family) DEBUG %s: unable to reset hardware: '%s' (HAL status %u) DEBUG %s: flow dst=%s, __FUNCTION__, XFRMSTRADDR(fl->fl6_dst, family) DEBUG %s: unable to start recv logic, dev->name DEBUG %s: flow src=%s, __FUNCTION__, XFRMSTRADDR(fl->fl6_src, family) DEBUG %s: %s: unable to reset hardware: '%s' (HAL status %u), DEBUG a guy asks for address mask. Who is it? DEBUG %s: %s: unable to start recv logic, DEBUG icmp v4 hw csum failure) DEBUG ath_mgtstart: discard, no xmit buf DEBUG expire>> %u %d %d %d, expire, DEBUG %s: [%02u] %-7s , tag, ix, ciphers[hk->kv_type] DEBUG expire++ %u %d %d %d, expire, DEBUG %02x, hk->kv_val[i] DEBUG rt_cache @%02x: %u.%u.%u.%u, hash, DEBUG mac %s, ether_sprintf(mac) DEBUG rt_bind_peer(0) @%p, NET_CALLER(iph) DEBUG %s , sc->sc_splitmic ? mic : rxmic DEBUG ip_rt_advice: redirect to DEBUG %02x, hk->kv_mic[i] DEBUG
Unified Services Router User Manual 196 ip_rt_bug: %u.%u.%u.%u -> %u.%u.%u.%u, %s, DEBUG txmic DEBUG UDP: short packet: From %u.%u.%u.%u:%u %d/%d to %u.%u.%u.%u:%u, DEBUG %02x, hk->kv_txmic[i] DEBUG UDP: bad checksum. From %d.%d.%d.%d:%d to %d.%d.%d.%d:%d ulen %d, DEBUG %s: unable to update h/w beacon queue parameters, DEBUG REJECT: ECHOREPLY no longer supported. DEBUG %s: stuck beacon; resetting (bmiss count %u), DEBUG ipt_rpc: only valid for PRE_ROUTING, FORWARD, POST_ROUTING, LOCAL_IN and/or LOCAL_OUT targets. DEBUG move data from NORMAL to XR DEBUG ip_nat_init: can't setup rules. DEBUG moved %d buffers from NORMAL to XR, index DEBUG ip_nat_init: can't register in hook. DEBUG move buffers from XR to NORMAL DEBUG ip_nat_init: can't register out hook. DEBUG moved %d buffers from XR to NORMAL, count DEBUG ip_nat_init: can't register adjust in hook. DEBUG %s:%d %s, __FILE__, __LINE__, __func__ DEBUG ip_nat_init: can't register adjust out hook. DEBUG %s:%d %s, __FILE__, __LINE__, __func__ DEBUG ip_nat_init: can't register local out hook. DEBUG %s: no buffer (%s), dev->name, __func__ DEBUG ip_nat_init: can't register local in hook. DEBUG %s: no skbuff (%s), dev->name, __func__ DEBUG ipt_hook: happy cracking. DEBUG %s: HAL qnum %u out of range, max %u!, DEBUG ip_conntrack: can't register pre-routing defrag hook. DEBUG grppoll_start: grppoll Buf allocation failed DEBUG ip_conntrack: can't register local_out defrag hook. DEBUG %s: HAL qnum %u out of range, max %u!, DEBUG ip_conntrack: can't register pre-routing hook. DEBUG %s: AC %u out of range, max %u!, DEBUG ip_conntrack: can't register local out hook. DEBUG %s: unable to update hardware queue DEBUG ip_conntrack: can't register local in helper hook. DEBUG %s: bogus frame type 0x%x (%s), dev->name, DEBUG ip_conntrack: can't register postrouting helper hook. DEBUG ath_stoprecv: rx queue 0x%x, link %p, DEBUG ip_conntrack: can't register post-routing hook. DEBUG %s: %s: unable to reset channel %u (%u MHz) DEBUG ip_conntrack: can't register local in hook. DEBUG %s: %s: unable to restart recv logic, DEBUG ip_conntrack: can't register to sysctl. DEBUG %s: unable to allocate channel table, dev->name DEBUG ip_conntrack_rtsp v IP_NF_RTSP_VERSION loading DEBUG %s: unable to allocate channel table, dev->name DEBUG ip_conntrack_rtsp: max_outstanding must be a positive integer DEBUG %s: unable to collect channel list from HAL; DEBUG ip_conntrack_rtsp: setup_timeout must be a positive integer DEBUG R (%p %llx) %08x %08x %08x %08x %08x %08x %c, DEBUG ip_conntrack_rtsp: ERROR registering port %d, ports[i] DEBUG T (%p %llx) %08x %08x %08x %08x %08x %08x %08x %08x %c, DEBUG ip_nat_rtsp v IP_NF_RTSP_VERSION loading DEBUG %s: no memory for sysctl table!, __func__ DEBUG %s: Sorry! Cannot find this match option., __FILE__ DEBUG %s: no memory for device name storage!, __func__ DEBUG
Unified Services Router User Manual 197 ipt_time loading DEBUG %s: failed to register sysctls!, sc->sc_dev->name DEBUG ipt_time unloaded DEBUG %s: mac %d.%d phy %d.%d, dev->name, DEBUG ip_conntrack_irc: max_dcc_channels must be a positive integer DEBUG 5 GHz radio %d.%d 2 GHz radio %d.%d, DEBUG ip_conntrack_irc: ERROR registering port %d, DEBUG radio %d.%d, ah->ah_analog5GhzRev >> 4, DEBUG ip_nat_h323: ip_nat_mangle_tcp_packet DEBUG radio %d.%d, ah->ah_analog5GhzRev >> 4, DEBUG ip_nat_h323: ip_nat_mangle_udp_packet DEBUG %s: Use hw queue %u for %s traffic, DEBUG ip_nat_h323: out of expectations DEBUG %s: Use hw queue %u for CAB traffic, dev->name, DEBUG ip_nat_h323: out of RTP ports DEBUG %s: Use hw queue %u for beacons, dev->name, DEBUG ip_nat_h323: out of TCP ports DEBUG Could not find Board Configuration Data DEBUG ip_nat_q931: out of TCP ports DEBUG Could not find Radio Configuration data DEBUG ip_nat_ras: out of TCP ports DEBUG ath_ahb: No devices found, driver not installed. DEBUG ip_nat_q931: out of TCP ports DEBUG _fmt, __VA_ARGS__ DEBUG ip_conntrack_core: Frag of proto %u., DEBUG _fmt, __VA_ARGS__ DEBUG Broadcast packet! DEBUG xlr8NatIpFinishOutput: Err.. skb2 == NULL ! DEBUG Should bcast: %u.%u.%u.%u->%u.%u.%u.%u (sk=%p, ptype=%u), DEBUG xlr8NatSoftCtxEnqueue: Calling xlr8NatIpFinishOutput () .., status DEBUG ip_conntrack version %s (%u buckets, %d max) DEBUG xlr8NatSoftCtxEnqueue: xlr8NatIpFinishOutput () returned [%d], status DEBUG ERROR registering port %d, DEBUG icmpExceptionHandler: Exception! DEBUG netfilter PSD loaded - (c) astaro AG DEBUG fragExceptionHandler: Exception! DEBUG netfilter PSD unloaded - (c) astaro AG DEBUG algExceptionHandler: Exception! DEBUG %s , SELF DEBUG dnsExceptionHandler: Exception! DEBUG %s , LAN DEBUG IPsecExceptionHandler: Exception! DEBUG %s , WAN DEBUG ESP Packet Src:%x Dest:%x Sport:%d dport:%d secure:%d spi:%d isr:%p, DEBUG TRUNCATED DEBUG xlr8NatConntrackPreHook: We found the valid context, DEBUG SRC=%u.%u.%u.%u DST=%u.%u.%u.%u , DEBUG xlr8NatConntrackPreHook: Not a secured packet. DEBUG LEN=%u TOS=0x%02X PREC=0x%02X TTL=%u ID=%u , DEBUG xlr8NatConntrackPreHook: isr=[%p], pIsr DEBUG FRAG:%u , ntohs(ih->frag_off) & IP_OFFSET DEBUG xlr8NatConntrackPreHook: secure=[%d], secure DEBUG TRUNCATED DEBUG Context found for ESP %p,pFlowEntry->post.pIsr[0] DEBUG PROTO=TCP DEBUG xlr8NatConntrackPreHook: New connection. DEBUG INCOMPLETE [%u bytes] , DEBUG xlr8NatConntrackPostHook: postSecure=[%d] postIsr=[%p %p], DEBUG SPT=%u DPT=%u , DEBUG proto %d spi %d <-------> proto %d spi %d,pPktInfo->proto,pPktInfo->spi, DEBUG SEQ=%u ACK=%u , DEBUG IPSEC_INF Clock skew detected DEBUG
Unified Services Router User Manual 198 WINDOW=%u , ntohs(th->window) DEBUG IPSEC_ERR [%s:%d]: Max (%d) No of SA Limit reached, DEBUG RES=0x%02x , (u8)(ntohl(tcp_flag_word(th) & TCP_RESERVED_BITS) >> 22) DEBUG IPSEC_ERR [%s:%d]: Max (%d) No of SA Limit reached, DEBUG URGP=%u , ntohs(th->urg_ptr) DEBUG IPSEC_ERR [%s:%d]: time(secs): %u DEBUG TRUNCATED DEBUG ERROR: Failed to add entry to IPsec sa table DEBUG %02X, op[i] DEBUG ERROR: Failed to add entry to IPsec sa table DEBUG PROTO=UDP DEBUG ERROR: Failed to add entry to IPsec sa table DEBUG INCOMPLETE [%u bytes] , DEBUG ERROR: Failed to add entry to IPsec sa table DEBUG SPT=%u DPT=%u LEN=%u , DEBUG ERROR: Failed to add entry to IPsec sa table DEBUG SPT=%u DPT=%u LEN=%u , DEBUG ERROR: Failed to add entry to IPsec sa table DEBUG PROTO=ICMP DEBUG unknown oid '%s', varName DEBUG INCOMPLETE [%u bytes] , DEBUG could not find oid pointer for '%s', varName DEBUG TYPE=%u CODE=%u , ich->type, ich->code DEBUG unRegistering IPsecMib ..... DEBUG INCOMPLETE [%u bytes] , DEBUG ERROR: Failed to add entry to IPsec sa table DEBUG ID=%u SEQ=%u , DEBUG ERROR: Failed to add entry to IPsec sa table DEBUG PARAMETER=%u , DEBUG ERROR: Failed to add entry to IPsec sa table DEBUG GATEWAY=%u.%u.%u.%u , DEBUG ERROR: Failed to add entry to IPsec sa table DEBUG MTU=%u , ntohs(ich->un.frag.mtu) DEBUG ERROR: Failed to add entry to IPsec sa table DEBUG PROTO=AH DEBUG ERROR: Failed to add entry to IPsec sa table DEBUG INCOMPLETE [%u bytes] , DEBUG unknown oid '%s', varName DEBUG SPI=0x%x , ntohl(ah->spi) DEBUG could not find oid pointer for '%s', varName DEBUG PROTO=ESP DEBUG unRegistering IPsecMib ..... DEBUG INCOMPLETE [%u bytes] , DEBUG . %u.%u.%u.%u, NIPQUAD(trt->rt_dst) DEBUG SPI=0x%x , ntohl(eh->spi) DEBUG %02x, *p DEBUG PROTO=%u , ih->protocol DEBUG . %u.%u.%u.%u, NIPQUAD(trt->rt_dst) DEBUG UID=%u , skb->sk->sk_socket->file->f_uid DEBUG %02x, *p DEBUG <%d>%sIN=%s OUT=%s , loginfo->u.log.level, DEBUG . %u.%u.%u.%u, NIPQUAD(trt->rt_dst) DEBUG level_string DEBUG %02x, *p DEBUG %sIN=%s OUT=%s , DEBUG . %u.%u.%u.%u, NIPQUAD(trt->rt_dst) DEBUG %s , prefix == NULL ? loginfo->prefix : prefix DEBUG %02x, *p DEBUG IN= DEBUG unable to register vIPsec kernel comp to UMI DEBUG OUT= DEBUG unregistering VIPSECK from UMI .... DEBUG PHYSIN=%s , physindev->name DEBUG in vIPsecKIoctlHandler cmd - %d, cmd DEBUG
Unified Services Router User Manual 199 PHYSOUT=%s , physoutdev->name DEBUG %s: Error. DST Refcount value less than 1 (%d), DEBUG MAC= DEBUG for %s DEVICE refcnt: %d ,pDst->dev->name, DEBUG %02x%c, *p, DEBUG %s: Got Null m:%p *m:%p sa:%p *sa:%p,__func__,ppBufMgr, DEBUG NAT: no longer support implicit source local NAT DEBUG %s Got Deleted SA:%p state:%d,__func__,pIPsecInfo,pIPsecInfo->state DEBUG NAT: packet src %u.%u.%u.%u -> dst %u.%u.%u.%u, DEBUG %s: %s: fmt, __FILE__, __FUNCTION__ , ## args) INFO SNAT: multiple ranges no longer supported DEBUG %s: %s: fmt, __FILE__, __FUNCTION__ , ## args) INFO format,##args) DEBUG ipt_TIME: format, ## args) INFO version DEBUG IPT_ACCOUNT_NAME : checkentry() wrong parameters (not equals existing table parameters). INFO offset_before=%d, offset_after=%d, correction_pos=%u, x->offset_before, x->offset_after, x->correction_pos DEBUG IPT_ACCOUNT_NAME : checkentry() too big netmask. INFO ip_ct_h323: DEBUG IPT_ACCOUNT_NAME : checkentry() failed to allocate %zu for new table %s., sizeof(struct t_ipt_account_table), info->name INFO ip_ct_h323: incomplete TPKT (fragmented?) DEBUG IPT_ACCOUNT_NAME : checkentry() wrong network/netmask. INFO ip_ct_h245: decoding error: %s, DEBUG account: Wrong netmask given by netmask parameter (%i). Valid is 32 to 0., netmask INFO ip_ct_h245: packet dropped DEBUG IPT_ACCOUNT_NAME : checkentry() failed to create procfs entry. INFO ip_ct_q931: decoding error: %s, DEBUG IPT_ACCOUNT_NAME : checkentry() failed to register match. INFO ip_ct_q931: packet dropped DEBUG failed to create procfs entry . INFO ip_ct_ras: decoding error: %s, DEBUG MPPE/MPPC encryption/compression module registered INFO ip_ct_ras: packet dropped DEBUG MPPE/MPPC encryption/compression module unregistered INFO ERROR registering port %d, DEBUG PPP generic driver version PPP_VERSION INFO ERROR registering port %d, DEBUG MPPE/MPPC encryption/compression module registered INFO ipt_connlimit [%d]: src=%u.%u.%u.%u:%d dst=%u.%u.%u.%u:%d %s, DEBUG MPPE/MPPC encryption/compression module unregistered INFO ipt_connlimit [%d]: src=%u.%u.%u.%u:%d dst=%u.%u.%u.%u:%d new, DEBUG PPP generic driver version PPP_VERSION INFO ipt_connlimit: Oops: invalid ct state ? DEBUG PPPoL2TP kernel driver, %s, INFO ipt_connlimit: Hmm, kmalloc failed :-( DEBUG PPPoL2TP kernel driver, %s, INFO ipt_connlimit: src=%u.%u.%u.%u mask=%u.%u.%u.%u DEBUG PPPoL2TP kernel driver, %s, INFO _lvl PPPOL2TP: _fmt, ##args DEBUG failed to create procfs entry . INFO %02X, ptr[length] DEBUG proc dir not created .. INFO %02X, ((unsigned char *) m-DEBUG Initialzing Product Data modules INFO
Unified Services Router User Manual 200 >msg_iov[i].iov_base)[j] %02X, skb->data[i] DEBUG De initializing by \ INFO _lvl PPPOL2TP: _fmt, ##args DEBUG kernel UMI module loaded INFO %02X, ptr[length] DEBUG kernel UMI module unloaded INFO %02X, ((unsigned char *) m->msg_iov[i].iov_base)[j] DEBUG Loading bridge module INFO %02X, skb->data[i] DEBUG Unloading bridge module INFO _lvl PPPOL2TP: _fmt, ##args DEBUG unsupported command %d, cmd INFO %02X, ptr[length] DEBUG Loading ifDev module INFO %02X, ((unsigned char *) m->msg_iov[i].iov_base)[j] DEBUG Unloading ifDev module INFO %02X, skb->data[i] DEBUG ERROR#%d in alloc_chrdev_region, result INFO KERN_EMERG THE value read is %d,value*/ DEBUG ERROR#%d in cdev_add, result INFO KERN_EMERG Factory Reset button is pressed DEBUG using bcm switch %s, bcmswitch INFO KERN_EMERG Returing error in INTR registration DEBUG privlegedID %d wanporttNo: %d, privlegedID,wanportNo INFO KERN_EMERG Initialzing Factory defaults modules DEBUG Loading mii INFO Failed to allocate memory for pSipListNode DEBUG Unloading mii INFO SIPALG: Memeory allocation failed for pSipNodeEntryTbl DEBUG %s: Version 0.1 INFO pkt-err %s, pktInfo.error DEBUG %s: driver unloaded, dev_info INFO pkt-err %s, pktInfo.error DEBUG wlan: %s backend registered, be->iab_name INFO pkt-err %s, pktInfo.error DEBUG wlan: %s backend unregistered, INFO %s Len=%d, msg, len DEBUG wlan: %s acl policy registered, iac->iac_name INFO %02x , ((uint8_t *) ptr)[i] DEBUG wlan: %s acl policy unregistered, iac->iac_name INFO End DEBUG %s, tmpbuf INFO CVM_MOD_EXP_BASE MISMATCH cmd=%x base=%x, cmd, DEBUG VLAN2 INFO op->sizeofptr = %ld, op->sizeofptr DEBUG VLAN3 INFO opcode cmd = %x, cmd DEBUG VLAN4 <%d %d>, INFO modexp opcode received DEBUG %s: %s, dev_info, version INFO Memory Allocation failed DEBUG %s: driver unloaded, dev_info INFO modexpcrt opcode received DEBUG %s, buf INFO kmalloc failed DEBUG %s: %s (, dev_info, ath_hal_version INFO kmalloc failed DEBUG %s: driver unloaded, dev_info INFO kmalloc failed DEBUG %s: %s: mem=0x%lx, irq=%d hw_base=0x%p, INFO kmalloc failed DEBUG %s: %s, dev_info, version INFO kmalloc Failed DEBUG %s: driver unloaded, dev_info INFO kmalloc failed DEBUG %s: %s: mem=0x%lx, irq=%d, INFO unknown cyrpto ioctl cmd received %x, cmd DEBUG %s: %s: mem=0x%lx, irq=%d, INFO register_chrdev returned ZERO DEBUG %s: %s, dev_info, version INFO const char *descr, krb5_keyblock *k) { DEBUG %s: driver unloaded, dev_info INFO F password, &pdata DEBUG %s, buf INFO
Unified Services Router User Manual 201 test key, key DEBUG %s: %s (, dev_info, ath_hal_version INFO pre-hashed key, key DEBUG %s: driver unloaded, dev_info INFO const char *descr, krb5_keyblock *k) { DEBUG %s: driver unloaded, dev_info INFO AES 128-bit key, &key DEBUG %s: Version 2.0.0 INFO const char *descr, krb5_keyblock *k) { DEBUG %s: driver unloaded, dev_info INFO test key, key DEBUG %s: driver unloaded, dev_info INFO pre-hashed key, key DEBUG wlan: %s backend registered, be->iab_name INFO const char *descr, krb5_keyblock *k) { DEBUG wlan: %s backend unregistered, INFO 128-bit AES key,&dk DEBUG wlan: %s acl policy registered, iac->iac_name INFO 256-bit AES key, &dk DEBUG wlan: %s acl policy unregistered, iac->iac_name INFO WARNING: DEBUG %s: %s, dev_info, version INFO bwMonMultipathNxtHopSelect:: checking rates DEBUG %s: driver unloaded, dev_info INFO hop :%d dev:%s usableBwLimit = %d currBwShare = %d lastHopSelected = %d weightedHopPrefer = %d , DEBUG %s: %s (, dev_info, ath_hal_version INFO 1. selecting hop: %d lastHopSelected = %d , selHop, lastHopSelected DEBUG %s: driver unloaded, dev_info INFO 4. hop :%d dev:%s usableBwLimit = %d currBwShare = %d lastHopSelected = %d weightedHopPrefer = %d , DEBUG %s: %s: mem=0x%lx, irq=%d, INFO 2. selecting hop: %d lastHopSelected = %d , selHop, lastHopSelected DEBUG %s: %s, dev_info, version INFO 3. selecting hop: %d lastHopSelected = %d , selHop, lastHopSelected DEBUG %s: driver unloaded, dev_info INFO bwMonitor multipath selection enabled DEBUG ath_pci: switching rfkill capability %s, INFO bwMonitor multipath selection disabled DEBUG Unknown autocreate mode: %s, INFO weightedHopPrefer set to %d ,weightedHopPrefer DEBUG %s: %s: mem=0x%lx, irq=%d, INFO bwMonitor sysctl registration failed DEBUG %s: %s, dev_info, version INFO bwMonitor sysctl registered DEBUG %s: driver unloaded, dev_info INFO bwMonitor sysctl not registered DEBUG %s: %s, dev_info, version INFO Unregistered bwMonitor sysctl DEBUG %s: unloaded, dev_info INFO CONFIG_SYSCTL enabled ... DEBUG %s: %s, dev_info, version INFO Initialized bandwidth monitor ... DEBUG %s: unloaded, dev_info INFO Removed bandwidth monitor ... DEBUG %s: %s, dev_info, version INFO Oops.. AES_GCM_encrypt failed (keylen:%u),key->cvm_keylen DEBUG %s: unloaded, dev_info INFO Oops.. AES_GCM_decrypt failed (keylen:%u),key->cvm_keylen DEBUG failed to create procfs entry . INFO %s, msg DEBUG ICMP: %u.%u.%u.%u: INFO %02x%s, data[i], DEBUG ICMP: %u.%u.%u.%u: Source INFO Failed to set AES encrypt key DEBUG Wrong address mask %u.%u.%u.%u from INFO Failed to set AES encrypt key DEBUG Redirect from %u.%u.%u.%u on %s about INFO AES %s Encrypt Test Duration: %d:%d, hard ? Hard : Soft, DEBUG IP: routing cache hash table of %u buckets, %ldKbytes, INFO Failed to set AES encrypt key DEBUG source route option %u.%u.%u.%u -> %u.%u.%u.%u, INFO
Unified Services Router User Manual 202 Failed to set AES encrypt key DEBUG ICMP: %u.%u.%u.%u: INFO AES %s Decrypt Test Duration: %d:%d, hard ? Hard : Soft, DEBUG ICMP: %u.%u.%u.%u: Source INFO Failed to set AES encrypt key DEBUG Wrong address mask %u.%u.%u.%u from INFO Failed to set AES encrypt key DEBUG Redirect from %u.%u.%u.%u on %s about INFO Failed to set AES encrypt key DEBUG IP: routing cache hash table of %u buckets, %ldKbytes, INFO Failed to set AES encrypt key DEBUG source route option %u.%u.%u.%u -> %u.%u.%u.%u, INFO Failed to set DES encrypt key[%d], i DEBUG Wrong address mask %u.%u.%u.%u from INFO Failed to set DES decrypt key[%d], i DEBUG Redirect from %u.%u.%u.%u on %s about INFO Failed to set DES encrypt key[%d], i DEBUG source route option INFO Failed to set DES decrypt key[%d], i DEBUG ICMP: %u.%u.%u.%u: INFO Failed to set DES encrypt key DEBUG ICMP: %u.%u.%u.%u: Source INFO Failed to set DES decrypt key DEBUG Wrong address mask %u.%u.%u.%u from INFO Failed to set DES encrypt key DEBUG Redirect from %u.%u.%u.%u on %s about INFO Failed to set DES decrypt key DEBUG IP: routing cache hash table of %u buckets, %ldKbytes, INFO AES Software Test: DEBUG source route option %u.%u.%u.%u -> %u.%u.%u.%u, INFO AES Software Test %s, aesSoftTest(0) ? Failed : Passed DEBUG IPsec: device unregistering: %s, dev->name INFO AES Hardware Test: DEBUG IPsec: device down: %s, dev->name INFO AES Hardware Test %s, aesHardTest(0) ? Failed : Passed DEBUG mark: only supports 32bit mark WARNING 3DES Software Test: DEBUG ipt_time: invalid argument WARNING 3DES Software Test %s, des3SoftTest(0) ? Failed : Passed DEBUG ipt_time: IPT_DAY didn't matched WARNING 3DES Hardware Test: DEBUG ./Logs_kernel.txt:45:KERN_WARNING WARNING 3DES Hardware Test %s, des3HardTest(0) ? Failed : Passed DEBUG ./Logs_kernel.txt:59:KERN_WARNING WARNING DES Software Test: DEBUG ipt_LOG: not logging via system console WARNING DES Software Test %s, desSoftTest(0) ? Failed : Passed DEBUG %s: wrong options length: %u, fname, opt_len WARNING DES Hardware Test: DEBUG %s: options rejected: o[0]=%02x, o[1]=%02x, WARNING DES Hardware Test %s, desHardTest(0) ? Failed : Passed DEBUG %s: wrong options length: %u, WARNING SHA Software Test: DEBUG %s: options rejected: o[0]=%02x, o[1]=%02x, WARNING SHA Software Test %s, shaSoftTest(0) ? Failed : Passed DEBUG %s: don't know what to do: o[5]=%02x, WARNING SHA Hardware Test: DEBUG %s: wrong options length: %u, fname, opt_len WARNING SHA Hardware Test %s, shaHardTest(0) ? Failed : Passed DEBUG %s: options rejected: o[0]=%02x, o[1]=%02x, WARNING MD5 Software Test: DEBUG %s: wrong options length: %u, WARNING
Unified Services Router User Manual 203 MD5 Software Test %s, md5SoftTest(0) ? Failed : Passed DEBUG %s: options rejected: o[0]=%02x, o[1]=%02x, WARNING MD5 Hardware Test: DEBUG %s: don't know what to do: o[5]=%02x, WARNING MD5 Hardware Test %s, md5HardTest(0) ? Failed : Passed DEBUG *** New port %d ***, ntohs(expinfo->natport) WARNING AES Software Test: %d iterations, iter DEBUG ** skb len %d, dlen %d,(*pskb)->len, WARNING AES Software Test Duration: %d:%d, DEBUG ********** Non linear skb WARNING AES Hardware Test: %d iterations, iter DEBUG End of sdp %p, nexthdr WARNING AES Hardware Test Duration: %d:%d, DEBUG %s: unknown pairwise cipher %d, WARNING 3DES Software Test: %d iterations, iter DEBUG %s: unknown group cipher %d, WARNING 3DES Software Test Duration: %d:%d, DEBUG %s: unknown SIOCSIWAUTH flag %d, WARNING 3DES Hardware Test: %d iterations, iter DEBUG %s: unknown SIOCGIWAUTH flag %d, WARNING 3DES Hardware Test Duration: %d:%d, DEBUG %s: unknown algorithm %d, WARNING DES Software Test: %d iterations, iter DEBUG %s: key size %d is too large, WARNING DES Software Test Duration: %d:%d, DEBUG try_module_get failed \ WARNING DES Hardware Test: %d iterations, iter DEBUG %s: request_irq failed, dev->name WARNING DES Hardware Test Duration: %d:%d, DEBUG try_module_get failed WARNING SHA Software Test: %d iterations, iter DEBUG try_module_get failed \ WARNING SHA Software Test Duration: %d:%d, DEBUG %s: unknown pairwise cipher %d, WARNING SHA Hardware Test: %d iterations, iter DEBUG %s: unknown group cipher %d, WARNING SHA Hardware Test Duration: %d:%d, DEBUG %s: unknown SIOCSIWAUTH flag %d, WARNING MD5 Software Test: %d iterations, iter DEBUG %s: unknown SIOCGIWAUTH flag %d, WARNING MD5 Software Test Duration: %d:%d, DEBUG %s: unknown algorithm %d, WARNING MD5 Hardware Test: %d iterations, iter DEBUG %s: key size %d is too large, WARNING MD5 Hardware Test Duration: %d:%d, DEBUG unable to load %s, scan_modnames[mode] WARNING ./pnac/src/pnac/linux/kernel/xcalibur.c:209:#define DEBUG_PRINTK printk DEBUG Failed to mkdir /proc/net/madwifi WARNING bcmDeviceInit: registration failed DEBUG try_module_get failed WARNING bcmDeviceInit: pCdev Add failed DEBUG %s: request_irq failed, dev->name WARNING REG Size == 8 Bit DEBUG too many virtual ap's (already got %d), sc->sc_nvaps WARNING Value = %x ::: At Page = %x : Addr = %x DEBUG %s: request_irq failed, dev->name WARNING REG Size == 16 Bit DEBUG rix %u (%u) bad ratekbps %u mode %u, WARNING
Unified Services Router User Manual 204 Value = %x ::: At Page = %x : Addr = %x DEBUG cix %u (%u) bad ratekbps %u mode %u, WARNING REG Size == 32 Bit DEBUG %s: no rates for %s?, WARNING Value = %x ::: At Page = %x : Addr = %x DEBUG no rates yet! mode %u, sc->sc_curmode WARNING REG Size == 64 Bit DEBUG %u.%u.%u.%u sent an invalid ICMP WARNING REG Size is not in 8/16/32/64 DEBUG dst cache overflow WARNING Written Value = %x ::: At Page = %x : Addr = %x DEBUG Neighbour table overflow. WARNING bcm_ioctl :Unknown Ioctl Case : DEBUG host %u.%u.%u.%u/if%d ignores WARNING =========Register Dump for Port Number # %d=========,port DEBUG martian destination %u.%u.%u.%u from WARNING %s : Read Status=%s data=%#x,regName[j], DEBUG martian source %u.%u.%u.%u from WARNING %s : Read Status=%s data=%#x,regName[j], DEBUG ll header: WARNING powerDeviceInit: device registration failed DEBUG %u.%u.%u.%u sent an invalid ICMP WARNING powerDeviceInit: adding device failed DEBUG dst cache overflow WARNING %s: Error: Big jump in pn number. TID=%d, from %x %x to %x %x. DEBUG Neighbour table overflow. WARNING %s: The MIC is corrupted. Drop this frame., __func__ DEBUG host %u.%u.%u.%u/if%d ignores WARNING %s: The MIC is OK. Still use this frame and update PN., __func__ DEBUG martian destination %u.%u.%u.%u from WARNING ADDBA send failed: recipient is not a 11n node DEBUG martian source %u.%u.%u.%u from WARNING Cannot Set Rate: %x, value DEBUG ll header: WARNING Getting Rate Series: %x,vap->iv_fixed_rate.series DEBUG %u.%u.%u.%u sent an invalid ICMP WARNING Getting Retry Series: %x,vap->iv_fixed_rate.retries DEBUG dst cache overflow WARNING IC Name: %s,ic->ic_dev->name DEBUG Neighbour table overflow. WARNING usage: rtparams rt_idx <0|1> per <0..100> probe_intval <0..100> DEBUG host %u.%u.%u.%u/if%d ignores WARNING usage: acparams ac <0|3> RTS <0|1> aggr scaling <0..4> min mbps <0..250> DEBUG martian source %u.%u.%u.%u from WARNING usage: hbrparams ac <2> enable <0|1> per_low <0..50> DEBUG ll header: WARNING %s(): ADDBA mode is AUTO, __func__ DEBUG martian destination %u.%u.%u.%u from WARNING %s(): Invalid TID value, __func__ DEBUG %u.%u.%u.%u sent an invalid ICMP WARNING %s(): ADDBA mode is AUTO, __func__ DEBUG dst cache overflow WARNING %s(): Invalid TID value, __func__ DEBUG Neighbour table overflow. WARNING %s(): Invalid TID value, __func__ DEBUG host %u.%u.%u.%u/if%d ignores WARNING Addba status IDLE DEBUG martian destination %u.%u.%u.%u WARNIN
Unified Services Router User Manual 205 from G %s(): ADDBA mode is AUTO, __func__ DEBUG martian source %u.%u.%u.%u from WARNING %s(): Invalid TID value, __func__ DEBUG ll header: WARNING Error in ADD- no node available DEBUG Unable to create ip_set_list ERROR %s(): Channel capabilities do not match, chan flags 0x%x, DEBUG Unable to create ip_set_hash ERROR %s: cannot map channel to mode; freq %u flags 0x%x, DEBUG ip_conntrack_in: Frag of proto %u (hook=%u), ERROR ic_get_currentCountry not initialized yet DEBUG Unable to register netfilter socket option ERROR Country ie is %c%c%c, DEBUG Unable to create ip_conntrack_hash ERROR %s: wrong state transition from %d to %d, DEBUG Unable to create ip_conntrack slab cache ERROR %s: wrong state transition from %d to %d, DEBUG Unable to create ip_expect slab cache ERROR %s: wrong state transition from %d to %d, DEBUG Unable to create ip_set_iptreeb slab cache ERROR %s: wrong state transition from %d to %d, DEBUG Unable to create ip_set_iptreed slab cache ERROR %s: wrong state transition from %d to %d, DEBUG %s: cannot allocate space for %scompressor, fname, ERROR %s: wrong state transition from %d to %d, DEBUG %s: cannot allocate space for MPPC history, ERROR ieee80211_deliver_l2uf: no buf available DEBUG %s: cannot allocate space for MPPC history, ERROR %s: %s, vap->iv_dev->name, buf /* NB: no */ DEBUG %s: cannot load ARC4 module, fname ERROR %s: [%s] %s, vap->iv_dev->name, DEBUG %s: cannot load SHA1 module, fname ERROR %s: [%s] %s, vap->iv_dev->name, ether_sprintf(mac), buf DEBUG %s: CryptoAPI SHA1 digest size too small, fname ERROR [%s:%s] discard %s frame, %s, vap->iv_dev->name, DEBUG %s: cannot allocate space for SHA1 digest, fname ERROR [%s:%s] discard frame, %s, vap->iv_dev->name, DEBUG %s%d: trying to write outside history ERROR [%s:%s] discard %s information element, %s, DEBUG %s%d: trying to write outside history ERROR [%s:%s] discard information element, %s, DEBUG %s%d: trying to write outside history ERROR [%s:%s] discard %s frame, %s, vap->iv_dev->name, DEBUG %s%d: too big uncompressed packet: %d, ERROR [%s:%s] discard frame, %s, vap->iv_dev->name, DEBUG %s%d: encryption negotiated but not an ERROR HBR list dumpNode\tAddress\t\t\tState\tTrigger\tBlock DEBUG %s%d: error - not an MPPC or MPPE frame ERROR Nodes informationAddress\t\t\tBlock\t\tDroped VI frames DEBUG Kernel doesn't provide ARC4 and/or SHA1 algorithms ERROR %d\t %2.2x:%2.2x:%2.2x:%2.2x:%2.2x:%2.2x\t%s\t%s\t%s, DEBUG PPP: not interface or channel?? ERROR %2.2x:%2.2x:%2.2x:%2.2x:%2.2x:%2.2x\t%s\t\t%d, DEBUG PPP: no memory (VJ compressor) ERROR [%d]\tFunction\t%s, j, ni->node_trace[i].funcp DEBUG failed to register PPP device (%d), err ERROR
Unified Services Router User Manual 206 [%d]\tMacAddr\t%s, j, DEBUG PPP: no memory (VJ comp pkt) ERROR [%d]\tDescp\t\t%s, j, ni->node_trace[i].descp DEBUG PPP: no memory (comp pkt) ERROR [%d]\tValue\t\t%llu(0x%llx), j, ni->node_trace[i].value, DEBUG ppp: compressor dropped pkt ERROR ifmedia_add: null ifm DEBUG PPP: no memory (fragment) ERROR Adding entry for DEBUG PPP: VJ uncompressed error ERROR ifmedia_set: no match for 0x%x/0x%x, DEBUG ppp_decompress_frame: no memory ERROR ifmedia_set: target DEBUG ppp_mp_reconstruct bad seq %u < %u, ERROR ifmedia_set: setting to DEBUG PPP: couldn't register device %s (%d), ERROR ifmedia_ioctl: switching %s to , dev->name DEBUG ppp: destroying ppp struct %p but dead=%d ERROR ifmedia_match: multiple match for DEBUG ppp: destroying undead channel %p !, ERROR <unknown type> DEBUG PPP: removing module but units remain! ERROR desc->ifmt_string DEBUG PPP: failed to unregister PPP device ERROR mode %s, desc->ifmt_string DEBUG %s: cannot allocate space for %scompressor, fname, ERROR <unknown subtype> DEBUG %s: cannot allocate space for MPPC history, ERROR %s, desc->ifmt_string DEBUG %s: cannot allocate space for MPPC history, ERROR %s%s, seen_option++ ? , : , DEBUG %s: cannot load ARC4 module, fname ERROR %s%s, seen_option++ ? , : , DEBUG %s: cannot load SHA1 module, fname ERROR %s, seen_option ? > : DEBUG %s: CryptoAPI SHA1 digest size too small, fname ERROR %s: %s, dev->name, buf DEBUG %s: cannot allocate space for SHA1 digest, fname ERROR %s: no memory for sysctl table!, __func__ DEBUG %s%d: trying to write outside history ERROR %s: failed to register sysctls!, vap->iv_dev->name DEBUG %s%d: trying to write outside history ERROR Atheros HAL assertion failure: %s: line %u: %s, DEBUG %s%d: trying to write outside history ERROR ath_hal: logging to %s %s, ath_hal_logfile, DEBUG %s%d: too big uncompressed packet: %d, ERROR ath_hal: logging disabled DEBUG %s%d: encryption negotiated but not an ERROR %s%s, sep, ath_hal_buildopts[i] DEBUG %s%d: error - not an MPPC or MPPE frame ERROR ath_pci: No devices found, driver not installed. DEBUG Kernel doesn't provide ARC4 and/or SHA1 algorithms ERROR ---:%d pri:%d qd:%u ad:%u sd:%u tot:%u amp:%d %02x:%02x:%02x, DEBUG PPP: not interface or channel?? ERROR SC Pushbutton Notify on %s::%s,dev->name,vap->iv_dev->name DEBUG PPP: no memory (VJ compressor) ERROR Could not find Board Configuration Data DEBUG failed to register PPP device (%d), err ERROR Could not find Radio Configuration data DEBUG PPP: no memory (comp pkt) ERROR %s: No device, __func__ DEBUG ppp: compressor dropped pkt ERROR ath_ahb: No devices found, driver not installed. DEBUG PPP: no memory (VJ comp pkt) ERROR PKTLOG_TAG %s:proc_dointvec failed, __FUNCTION__ DEBUG PPP: no memory (comp pkt) ERROR PKTLOG_TAG %s:proc_dointvec failed, DEBUG PPP: no memory (fragment) ERROR
Unified Services Router User Manual 207 __FUNCTION__ %s: failed to register sysctls!, proc_name DEBUG PPP: VJ uncompressed error ERROR PKTLOG_TAG %s: proc_mkdir failed, __FUNCTION__ DEBUG ppp_decompress_frame: no memory ERROR PKTLOG_TAG %s: pktlog_attach failed for %s, DEBUG ppp_mp_reconstruct bad seq %u < %u, ERROR PKTLOG_TAG %s:allocation failed for pl_info, __FUNCTION__ DEBUG PPP: couldn't register device %s (%d), ERROR PKTLOG_TAG %s:allocation failed for pl_info, __FUNCTION__ DEBUG ppp: destroying ppp struct %p but dead=%d ERROR PKTLOG_TAG %s: create_proc_entry failed for %s, DEBUG ppp: destroying undead channel %p !, ERROR PKTLOG_TAG %s: sysctl register failed for %s, DEBUG PPP: removing module but units remain! ERROR PKTLOG_TAG %s: page fault out of range, __FUNCTION__ DEBUG PPP: failed to unregister PPP device ERROR PKTLOG_TAG %s: page fault out of range, __FUNCTION__ DEBUG JBD: bad block at offset %u, ERROR PKTLOG_TAG %s: Log buffer unavailable, __FUNCTION__ DEBUG JBD: corrupted journal superblock ERROR PKTLOG_TAG DEBUG JBD: bad block at offset %u, ERROR Logging should be disabled before changing bufer size DEBUG JBD: Failed to read block at offset %u, ERROR %s:allocation failed for pl_info, __func__ DEBUG JBD: error %d scanning journal, err ERROR %s: Unable to allocate buffer, __func__ DEBUG JBD: IO error %d recovering block ERROR %s:allocation failed for pl_info, __func__ DEBUG ./Logs_kernel.txt:303:KERN_ERR ERROR %s: Unable to allocate buffer, __func__ DEBUG ./Logs_kernel.txt:304:KERN_ERR ERROR Atheros HAL assertion failure: %s: line %u: %s, DEBUG JBD: recovery pass %d ended at ERROR ath_hal: logging to %s %s, ath_hal_logfile, DEBUG %s: %s:%d: BAD SESSION MAGIC \ ERROR ath_hal: logging disabled DEBUG %s: %s:%d: BAD TUNNEL MAGIC \ ERROR %s%s, sep, ath_hal_buildopts[i] DEBUG msg->msg_namelen wrong, %d, msg->msg_namelen ERROR failed to allocate rx descriptors: %d, error DEBUG addr family wrong: %d, usin->sin_family ERROR ath_stoprecv: rx queue %p, link %p, DEBUG udp addr=%x/%hu, usin->sin_addr.s_addr, usin->sin_port ERROR no mpdu (%s), __func__ DEBUG %s: %s:%d: BAD TUNNEL MAGIC ERROR Reset rx chain mask. Do internal reset. (%s), __func__ DEBUG %s: %s:%d: BAD TUNNEL MAGIC ERROR OS_CANCEL_TIMER failed!! DEBUG socki_lookup: socket file changed! ERROR %s: unable to allocate channel table, __func__ DEBUG %s: %s:%d: BAD TUNNEL MAGIC ERROR %s: unable to collect channel list from hal; DEBUG %s: %s:%d: BAD SESSION MAGIC \ ERROR %s: cannot map channel to mode; freq %u flags 0x%x, DEBUG %s: %s:%d: BAD TUNNEL MAGIC \ ERROR %s: unable to reset channel %u (%uMhz) DEBUG msg->msg_namelen wrong, %d, msg->msg_namelen ERROR %s: unable to restart recv logic, DEBUG addr family wrong: %d, usin->sin_family ERROR %s: start DFS WAIT period on channel %d, __func__,sc->sc_curchan.channel DEBUG udp addr=%x/%hu, usin->sin_addr.s_addr, usin->sin_port ERROR
Unified Services Router User Manual 208 %s: cancel DFS WAIT period on channel %d, __func__, sc->sc_curchan.channel DEBUG %s: %s:%d: BAD TUNNEL MAGIC ERROR Non-DFS channel, cancelling previous DFS wait timer channel %d, sc->sc_curchan.channel DEBUG %s: %s:%d: BAD TUNNEL MAGIC ERROR %s: unable to reset hardware; hal status %u DEBUG socki_lookup: socket file changed! ERROR %s: unable to start recv logic, __func__ DEBUG %s: %s:%d: BAD TUNNEL MAGIC ERROR %s: unable to start recv logic, __func__ DEBUG %s: %s:%d: BAD SESSION MAGIC \ ERROR %s: unable to reset hardware; hal status %u, DEBUG %s: %s:%d: BAD TUNNEL MAGIC \ ERROR hardware error; reseting DEBUG msg->msg_namelen wrong, %d, msg->msg_namelen ERROR rx FIFO overrun; reseting DEBUG addr family wrong: %d, usin->sin_family ERROR %s: During Wow Sleep and got BMISS, __func__ DEBUG udp addr=%x/%hu, usin->sin_addr.s_addr, usin->sin_port ERROR AC\tRTS \tAggr Scaling\tMin Rate(Kbps)\tHBR \tPER LOW THRESHOLD DEBUG %s: %s:%d: BAD TUNNEL MAGIC ERROR BE\t%s\t\t%d\t%6d\t\t%s\t%d, DEBUG %s: %s:%d: BAD TUNNEL MAGIC ERROR BK\t%s\t\t%d\t%6d\t\t%s\t%d, DEBUG socki_lookup: socket file changed! ERROR VI\t%s\t\t%d\t%6d\t\t%s\t%d, DEBUG %s: %s:%d: BAD TUNNEL MAGIC ERROR VO\t%s\t\t%d\t%6d\t\t%s\t%d, DEBUG rebootHook: null function pointer ERROR --%d,%p,%lu:0x%x 0x%x 0x%p 0x%x 0x%x 0x%x 0x%x, DEBUG Bad ioctl command ERROR bb state: 0x%08x 0x%08x, bbstate(sc, 4ul), bbstate(sc, 5ul) DEBUG fResetMod: Failed to configure gpio pin ERROR %08x %08x %08x %08x %08x %08x %08x %08x%08x %08x %08x %08x, DEBUG fResetMod: Failed to register interrupt handler ERROR noise floor: (%d, %d) (%d, %d) (%d, %d), DEBUG registering char device failed ERROR %p: %08x %08x %08x %08x %08x %08x %08x %08x %08x %08x %08x %08x, DEBUG unregistering char device failed ERROR --%d,%p,%lu:0x%x 0x%x 0x%p 0x%x 0x%x 0x%x 0x%x, DEBUG proc entry delete failed ERROR %08x %08x %08x %08x %08x %08x %08x %08x%08x %08x %08x %08x, DEBUG proc entry initialization failed ERROR %s: unable to allocate device object., __func__ DEBUG testCompHandler: received %s from %d, (char *)pInBuf, ERROR %s: unable to attach hardware; HAL status %u, DEBUG UMI proto registration failed %d,ret ERROR %s: HAL ABI msmatch; DEBUG AF_UMI registration failed %d,ret ERROR %s: Warning, using only %u entries in %u key cache, DEBUG umi initialization failed %d,ret ERROR unable to setup a beacon xmit queue! DEBUG kernel UMI registration failed! ERROR unable to setup CAB xmit queue! DEBUG ./Logs_kernel.txt:447:KERN_ERR ERROR unable to setup xmit queue for BE traffic! DEBUG ERROR msm not found properly %d, len %d, msm, ERROR %s DFS attach failed, __func__ DEBUG ModExp returned Error ERROR %s: Invalid interface id = %u, __func__, if_id DEBUG ModExp returned Error ERROR %s:grppoll Buf allocation failed DEBUG %s: 0x%p len %u, tag, p, (unsigned ERROR
Unified Services Router User Manual 209 ,__func__ int)len %s: unable to start recv logic, DEBUG %03d:, i ERROR %s: Invalid interface id = %u, __func__, if_id DEBUG %02x, ((unsigned char *)p)[i] ERROR %s: unable to allocate channel table, __func__ DEBUG mic check failed ERROR %s: Tx Antenna Switch. Do internal reset., __func__ DEBUG %s: 0x%p len %u, tag, p, (unsigned int)len ERROR Radar found on channel %d (%d MHz), DEBUG %03d:, i ERROR End of DFS wait period DEBUG %02x, ((unsigned char *)p)[i] ERROR %s error allocating beacon, __func__ DEBUG mic check failed ERROR failed to allocate UAPSD QoS NULL tx descriptors: %d, error DEBUG [%s] Wrong parameters, __func__ ERROR failed to allocate UAPSD QoS NULL wbuf DEBUG [%s] Wrong Key length, __func__ ERROR %s: unable to allocate channel table, __func__ DEBUG [%s] Wrong parameters, __func__ ERROR %s: unable to update h/w beacon queue parameters, DEBUG [%s] Wrong Key length, __func__ ERROR ALREADY ACTIVATED DEBUG [%s] Wrong parameters, __func__ ERROR %s: missed %u consecutive beacons, DEBUG [%s] Wrong Key length, __func__ ERROR %s: busy times: rx_clear=%d, rx_frame=%d, tx_frame=%d, __func__, rx_clear, rx_frame, tx_frame DEBUG [%s] Wrong parameters, __func__ ERROR %s: unable to obtain busy times, __func__ DEBUG [%s] Wrong Key length, __func__ ERROR %s: beacon is officially stuck, DEBUG [%s]: Wrong parameters, __func__ ERROR Busy environment detected DEBUG [%s] Wrong Key Length %d, __func__, des_key_len ERROR Inteference detected DEBUG [%s] Wrong parameters %d, __func__, des_key_len ERROR rx_clear=%d, rx_frame=%d, tx_frame=%d, DEBUG [%s] Wrong Key Length %d, __func__, des_key_len ERROR %s: resume beacon xmit after %u misses, DEBUG [%s] Wrong parameters, __func__ ERROR %s: stuck beacon; resetting (bmiss count %u), DEBUG [%s] Wrong Key Length, __func__ ERROR EMPTY QUEUE DEBUG [%s] Wrong parameters, __func__ ERROR SWRInfo: seqno %d isswRetry %d retryCnt %d,wh ? (*(u_int16_t *)&wh->i_seq[0]) >> 4 : 0, bf->bf_isswretry,bf->bf_swretries DEBUG [%s] Wrong Key Length, __func__ ERROR Buffer #%08X --> Next#%08X Prev#%08X Last#%08X,bf, TAILQ_NEXT(bf,bf_list), DEBUG [%s] Wrong parameters, __func__ ERROR Stas#%08X flag#%08X Node#%08X, bf->bf_status, bf->bf_flags, bf->bf_node DEBUG [%s] Wrong parameters, __func__ ERROR Descr #%08X --> Next#%08X Data#%08X Ctl0#%08X Ctl1#%08X, bf->bf_daddr, ds->ds_link, ds->ds_data, ds->ds_ctl0, ds->ds_ctl1 DEBUG [%s] Wrong parameters, __func__ ERROR Ctl2#%08X Ctl3#%08X Sta0#%08X Sta1#%08X,ds->ds_hw[0], ds->ds_hw[1], lastds->ds_hw[2], lastds->ds_hw[3] DEBUG [%s] Wrong parameters, __func__ ERROR Error entering wow mode DEBUG device name=%s not found, pReq-ERROR
Unified Services Router User Manual 210 >ifName Wakingup due to wow signal DEBUG unable to register KIFDEV to UMI ERROR %s, wowStatus = 0x%x, __func__, wowStatus DEBUG ERROR: %s: Timeout at page %#0x addr %#0x ERROR Pattern added already DEBUG ERROR: %s: Timeout at page %#0x addr %#0x ERROR Error : All the %d pattern are in use. Cannot add a new pattern , MAX_NUM_PATTERN DEBUG Invalid IOCTL %#08x, cmd ERROR Pattern added to entry %d ,i DEBUG %s: unable to register device, dev->name ERROR Remove wake up pattern DEBUG ath_pci: 32-bit DMA not available ERROR mask = %p pat = %p ,maskBytes,patternBytes DEBUG ath_pci: cannot reserve PCI memory region ERROR mask = %x pat = %x ,(u_int32_t)maskBytes, (u_int32_t)patternBytes DEBUG ath_pci: cannot remap PCI memory region) ; ERROR Pattern Removed from entry %d ,i DEBUG ath_pci: no memory for device state ERROR Error : Pattern not found DEBUG %s: unable to register device, dev->name ERROR PPM STATE ILLEGAL %x %x, forcePpmStateCur, afp->forceState DEBUG ath_dev_probe: no memory for device state ERROR FORCE_PPM %4d %6.6x %8.8x %8.8x %8.8x %3.3x %4.4x, DEBUG %s: no memory for device state, __func__ ERROR failed to allocate tx descriptors: %d, error DEBUG kernel MIBCTL registration failed! ERROR failed to allocate beacon descripotrs: %d, error DEBUG Bad ioctl command ERROR failed to allocate UAPSD descripotrs: %d, error DEBUG WpsMod: Failed to configure gpio pin ERROR hal qnum %u out of range, max %u!, DEBUG WpsMod: Failed to register interrupt handler ERROR HAL AC %u out of range, max %zu!, DEBUG registering char device failed ERROR HAL AC %u out of range, max %zu!, DEBUG unregistering char device failed ERROR %s: unable to update hardware queue %u!, DEBUG %s:%d - ERROR: non-NULL node pointer in %p, %p<%s>! ERROR Multicast Q: DEBUG %s:%d - ERROR: non-NULL node pointer in %p, %p<%s>! ERROR %p , buf DEBUG can't alloc name %s, name ERROR buf flags - 0x%08x --------- , buf->bf_flags DEBUG %s: unable to register device, dev->name ERROR buf status - 0x%08x, buf->bf_status DEBUG failed to automatically load module: %s; \ ERROR # frames in aggr - %d, length of aggregate - %d, length of frame - %d, sequence number - %d, tidno - %d, DEBUG Unable to load needed module: %s; no support for \ ERROR isdata: %d isaggr: %d isampdu: %d ht: %d isretried: %d isxretried: %d shpreamble: %d isbar: %d ispspoll: %d aggrburst: %d calcairtime: %d qosnulleosp: %d, DEBUG Module \%s\ is not known, buf ERROR %p: 0x%08x 0x%08x 0x%08x 0x%08x 0x%08x 0x%08x 0x%08x 0x%08x 0x%08x 0x%08x, DEBUG Error loading module \%s\, buf ERROR 0x%08x 0x%08x 0x%08x 0x%08x 0x%08x 0x%08x 0x%08x 0x%08x DEBUG Module \%s\ failed to initialize, buf ERROR
Unified Services Router User Manual 211 0x%08x 0x%08x, 0x%08x 0x%08x 0x%08x 0x%08x, DEBUG ath_pci: 32-bit DMA not available ERROR sc_txq[%d] : , i DEBUG ath_pci: cannot reserve PCI memory region ERROR tid %p pause %d : , tid, tid->paused DEBUG ath_pci: cannot remap PCI memory region) ; ERROR %d: %p , j, tid->tx_buf[j] DEBUG ath_pci: no memory for device state ERROR %p , buf DEBUG %s: unable to attach hardware: '%s' (HAL status %u), ERROR axq_q: DEBUG %s: HAL ABI mismatch; ERROR %s: unable to reset hardware; hal status %u, __func__, status DEBUG %s: failed to allocate descriptors: %d, ERROR ****ASSERTION HIT**** DEBUG %s: unable to setup a beacon xmit queue!, ERROR MacAddr=%s, DEBUG %s: unable to setup CAB xmit queue!, ERROR TxBufIdx=%d, i DEBUG %s: unable to setup xmit queue for %s traffic!, ERROR Tid=%d, tidno DEBUG %s: unable to register device, dev->name ERROR AthBuf=%p, tid->tx_buf[i] DEBUG %s: autocreation of VAP failed: %d, ERROR %s: unable to reset hardware; hal status %u, DEBUG ath_dev_probe: no memory for device state ERROR %s: unable to reset hardware; hal status %u, DEBUG kdot11RogueAPEnable called with NULL argument. ERROR %s: unable to start recv logic, DEBUG kdot11RogueAPEnable: can not add more interfaces ERROR _fmt, __VA_ARGS__ \ DEBUG kdot11RogueAPGetState called with NULL argument. ERROR sample_pri=%d is a multiple of refpri=%d, sample_pri, refpri DEBUG kdot11RogueAPDisable called with NULL argument. ERROR ===========ft->ft_numfilters=%u===========, ft->ft_numfilters DEBUG %s: SKB does not exist., __FUNCTION__ ERROR filter[%d] filterID = %d rf_numpulses=%u; rf->rf_minpri=%u; rf->rf_maxpri=%u; rf->rf_threshold=%u; rf->rf_filterlen=%u; rf->rf_mindur=%u; rf->rf_maxdur=%u,j, rf->rf_pulseid, DEBUG %s: recvd invalid skb ERROR NOL DEBUG unable to register KIFDEV to UMI ERROR WARNING!!! 10 minute CAC period as channel is a weather radar channel DEBUG The system is going to factory defaults........!!! CRITICAL %s disable detects, __func__ DEBUG %s, msg CRITICAL %s enable detects, __func__ DEBUG %02x, *(data + i) CRITICAL %s disable FFT val=0x%x , __func__, val DEBUG Inside crypt_open in driver ###### CRITICAL %s enable FFT val=0x%x , __func__, val DEBUG Inside crypt_release in driver ###### CRITICAL %s debug level now = 0x%x , __func__, dfs_debug_level DEBUG Inside crypt_init module in driver @@@@@@@@ CRITICAL RateTable:%d, maxvalidrate:%d, ratemax:%d, pRc->rateTableSize,k,pRc->rateMaxPhy DEBUG Inside crypt_cleanup module in driver @@@@@@@@ CRITICAL %s: txRate value of 0x%x is bad., __FUNCTION__, txRate DEBUG SKB is null : %p ,skb CRITICAL Valid Rate Table:- DEBUG DST is null : %p ,dst CRITICAL
Unified Services Router User Manual 212 Index:%d, value:%d, code:%x, rate:%d, flag:%x, i, (int)validRateIndex[i], DEBUG DEV is null %p %p ,dev,dst CRITICAL RateTable:%d, maxvalidrate:%d, ratemax:%d, pRc->rateTableSize,k,pRc->rateMaxPhy DEBUG Packet is Fragmented %d,pBufMgr->len CRITICAL Can't allocate memory for ath_vap. DEBUG Marked the packet proto:%d sip:%x dip:%x sport:%d dport:%d spi:%d,isr:%p:%p %p CRITICAL Unable to add an interface for ath_dev. DEBUG SAV CHECK FAILED IN DECRYPTION CRITICAL %s: [%02u] %-7s , tag, ix, ciphers[hk->kv_type] DEBUG FAST PATH Breaks on BUF CHECK CRITICAL %02x, hk->kv_val[i] DEBUG FAST PATH Breaks on DST CHECK CRITICAL mac %02x-%02x-%02x-%02x-%02x-%02x, mac[0], mac[1], mac[2], mac[3], mac[4], mac[5] DEBUG FAST PATH Breaks on MTU %d %d %d,bufMgrLen(pBufMgr),mtu,dst_mtu(pDst->path) CRITICAL mac 00-00-00-00-00-00 DEBUG FAST PATH Breaks on MAX PACKET %d %d,bufMgrLen(pBufMgr),IP_MAX_PACKET CRITICAL %02x, hk->kv_mic[i] DEBUG SAV CHECK FAILED IN ENCRYPTION CRITICAL txmic DEBUG Match Found proto %d spi %d,pPktInfo->proto,pFlowEntry->pre.spi CRITICAL %02x, hk->kv_txmic[i] DEBUG PRE: proto: %u srcip:%u.%u.%u.%u sport :%u dstip: %u.%u.%u.%u dport: %u, CRITICAL Cannot support setting tx and rx keys individually DEBUG POST: proto: %u srcip:%u.%u.%u.%u sport :%u dstip: %u.%u.%u.%u dport: %u, CRITICAL bogus frame type 0x%x (%s), DEBUG Clearing the ISR %p,p CRITICAL ERROR: ieee80211_encap ret NULL DEBUG PROTO:%d %u.%u.%u.%u--->%u.%u.%u.%u, CRITICAL ERROR: ath_amsdu_attach not called DEBUG ESP-DONE: %p %p,sav,m CRITICAL %s: no memory for cwm attach, __func__ DEBUG ESP-BAD: %p %p,sav,m CRITICAL %s: error - acw NULL. Possible attach failure, __func__ DEBUG Bug in ip_route_input_slow(). CRITICAL %s: unable to abort tx dma, __func__ DEBUG Bug in ip_route_input_slow(). CRITICAL %s: no memory for ff attach, __func__ DEBUG Bug in ip_route_input \ CRITICAL Failed to initiate PBC based enrolle association DEBUG Bug in ip_route_input_slow(). CRITICAL KERN_EMERG Returing error in INTR registration DEBUG AH: Assigning the secure flags for sav :%p,sav CRITICAL KERN_EMERG Initialzing Wps module DEBUG ESP: Assigning the secure flags for sav :%p skb:%p src:%x dst:%x,sav,skb,ip->ip_src.s_addr,ip->ip_dst.s_addr CRITICAL %s:%d %s, __FILE__, __LINE__, __func__ DEBUG %s Buffer %d mtu %d path mtu %d header %d trailer %d,__func__,bufMgrLen(pBufMgr),mtu,dst_mtu(pDst->path),pDst->header_len,pDst->trailer_len CRITICAL
Unified Services Router User Manual 213 Appendix E. RJ-45 Pin-outs Signal RJ-45 Cable Adapter Signal RJ-45 PIN DB-9 PIN CTS NC NC NC DTR NC NC NC TxD 6 3 RxD GND 5 5 GND GND 4 5 GND RxD 3 2 TxD DSR NC NC NC RTS NC NC NC
Unified Services Router User Manual 214 Appendix F. Product Statement 1. DSR-1000N Federal Communications Commission (FCC) Compliance Notice: Radio Frequency Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:  Reorient or relocate the receiving antenna.  Increase the separation between the equipment and receiver.  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference, and 2) This device must accept any interference received, including interference that may cause undesired operation. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The antennas used for this transmitter must be installed to provide a spectrum distance of at least 20cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. This transmitter is restricted to indoor use in the 5150MHz to 5250MHz frequency range. Non-modification Statement Use only the integral antenna supplied by the manufacturer when operating this device. Unauthorized antennas, modifications, or attachments could damage the TI Navigator access point and violate FCC regulations. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. Canadian Department of Communications Industry Canada (IC) Notice This Class B digital apparatus complies with Canadian ICES-003 and RSS-210. Cet appareil numérique de la classe B est conforme à la norme NMB-003 et CNR-210 du Canada. ndustry Canada Statement This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference, and 2) This device must accept any interference received, including interference that may cause undesired operation.
Unified Services Router User Manual 215 IMPORTANT NOTE: Radiation Exposure Statement This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. To maintain compliance with IC RF exposure compliance requirements, please follow operation instruction as documented in this manual. This transmitter is restricted to indoor use in the 5150MHz to 5250MHz frequency range. Europe – EU Declaration of Conformity This device complies with the essential requirements of the R&TTE Directive 1999/5/EC. The following test methods have been applied in order to prove presumption of conformity with the essential requirements of the R&TTE Directive 1999/5/EC: - EN 60950-1: 2006+A11:2009 Safety of information technology equipment - EN 300 328 V1.7.1 (2006-10) Electromagnetic compatibility and Radio spectrum Matters (ERM); Wideband transmission systems; Data transmission equipment operating in the 2,4 GHz ISM band and using wide band modulation techniques; Harmonized EN covering essential requirements under article 3.2 of the R&TTE Directive - EN 301 893-1 V1.5.1 (2008-12) Broadband Radio Access Networks (BRAN); 5 GHz high performance RLAN; Harmonized EN covering essential requirements of article 3.2 of the R&TTE Directive - EN 301 489-17 V1.3.2 (2008-04) and EN 301 489-1 V1.8.1 (2008-04) Electromagnetic compatibility and Radio spectrum Matters (ERM); Electro Magnetic Compatibility (EMC) standard for radio equipment and services; Part 17: Specific conditions for 2,4 GHz wideband transmission systems and 5 GHz high performance RLAN equipment This device is a 2.4 GHz wideband transmission system (transceiver), intended for use in all EU member states and EFTA countries under the following conditions and/or with the following restrictions: - In Italy the end-user should apply for a license at the national spectrum authorities in order to obtain authorization to use the device for setting up outdoor radio links and/or for supplying public access to telecommunications and/or network services. - This device may not be used for setting up outdoor radio links in France and in some areas the RF output power may be limited to 10 mW EIRP in the frequency range of 2454 – 2483.5 MHz. For detailed information the enduser should contact the national spectrum authority in France. This device is a 5 GHz wideband transmission system (transceiver), intended for use in all EU member states and EFTA countries under the following conditions and/or with the following restrictions: - This device may only be used indoors in the frequency bands 5150 – 5250 MHz. - In France and Luxembourg a limited implementation of the frequency bands 5150 – 5250 MHz and 5250 – 5350 MHz. In Luxermbourg it is not allowed to make use of the frequency band 5470 – 5725 MHz. End-users are encouraged to contact the national spectrum authorities in France and Luxembourg in order to obtain the latest information about any restrictions in the 5 GHz frequency band(s).
Unified Services Router User Manual 216 Česky [Czech] [D-Link Corporation] tímto prohlašuje, že tento [DSR-1000N] je ve shodě se základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES. Dansk [Danish] Undertegnede [D-Link Corporation] erklærer herved, at følgende udstyr [DSR-1000N] overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF. Deutsch [German] Hiermit erklärt [D-Link Corporation], dass sich das Gerät [DSR-1000N] in Übereinstimmung mit den grundlegenden Anforderungen und den übrigen einschlägigen Bestimmungen der Richtlinie 1999/5/EG befindet. Eesti [Estonian] Käesolevaga kinnitab [D-Link Corporation] seadme [DSR-1000N] vastavust direktiivi 1999/5/EÜ põhinõuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele sätetele. English Hereby, [D-Link Corporation], declares that this [DSR-1000N] is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. Español [Spanish] Por medio de la presente [D-Link Corporation] declara que el [DSR-1000N] cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE. Ελληνική [Greek] ΜΕ ΣΗΝ ΠΑΡΟΤ΢Α [D-Link Corporation] ΔΗΛΩΝΕΙ ΟΣΙ [DSR-1000N] ΢ΤΜΜΟΡΦΩΝΕΣΑΙ ΠΡΟ΢ ΣΙ΢ ΟΤ΢ΙΩΔΕΙ΢ ΑΠΑΙΣΗ΢ΕΙ΢ ΚΑΙ ΣΙ΢ ΛΟΙΠΕ΢ ΢ΥΕΣΙΚΕ΢ ΔΙΑΣΑΞΕΙ΢ ΣΗ΢ ΟΔΗΓΙΑ΢ 1999/5/ΕΚ. Français [French] Par la présente [D-Link Corporation] déclare que l'appareil [DSR-1000N] est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE. Italiano [Italian] Con la presente [D-Link Corporation] dichiara che questo [DSR-1000N] è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE. Latviski [Latvian] Ar šo [D-Link Corporation] deklarē, ka [DSR-1000N] atbilst Direktīvas 1999/5/EK būtiskajām prasībām un citiem ar to saistītajiem noteikumiem. Lietuvių [Lithuanian] Šiuo [D-Link Corporation] deklaruoja, kad šis [DSR-1000N] atitinka esminius reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas. Nederlands [Dutch] Hierbij verklaart [D-Link Corporation] dat het toestel [DSR-1000N] in overeenstemming is met de essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/EG. Malti [Maltese] Hawnhekk, [D-Link Corporation], jiddikjara li dan [DSR-1000N] jikkonforma mal-ħtiġijiet essenzjali u ma provvedimenti oħrajn relevanti li hemm fid-Dirrettiva 1999/5/EC. Magyar [Hungarian] Alulírott, [D-Link Corporation] nyilatkozom, hogy a [DSR-1000N] megfelel a vonatkozó alapvetõ követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak. Polski [Polish] Niniejszym [D-Link Corporation] oświadcza, że [DSR-1000N] jest zgodny z zasadniczymi wymogami oraz pozostałymi stosownymi postanowieniami Dyrektywy 1999/5/EC.
Unified Services Router User Manual 217 Português [Portuguese] [D-Link Corporation] declara que este [DSR-1000N]está conforme com os requisitos essenciais e outras disposições da Directiva 1999/5/CE. Slovensko [Slovenian] [D-Link Corporation] izjavlja, da je ta [DSR-1000N] v skladu z bistvenimi zahtevami in ostalimi relevantnimi določili direktive 1999/5/ES. Slovensky [Slovak] [D-Link Corporation] týmto vyhlasuje, že [DSR-1000N] spĺňa základné požiadavky a všetky príslušné ustanovenia Smernice 1999/5/ES. Suomi [Finnish] [D-Link Corporation] vakuuttaa täten että [DSR-1000N] tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen. Svenska [Swedish] Härmed intygar [D-Link Corporation] att denna [DSR-1000N] står I överensstämmelse med de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv 1999/5/EG.
Unified Services Router User Manual 218 2.DSR-500N Federal Communications Commission (FCC) Compliance Notice: Radio Frequency Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:  Reorient or relocate the receiving antenna.  Increase the separation between the equipment and receiver.  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference, and 2) This device must accept any interference received, including interference that may cause undesired operation. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The antennas used for this transmitter must be installed to provide a spectrum distance of at least 20cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. This transmitter is restricted to indoor use in the 5150MHz to 5250MHz frequency range. Non-modification Statement Use only the integral antenna supplied by the manufacturer when operating this device. Unauthorized antennas, modifications, or attachments could damage the TI Navigator access point and violate FCC regulations. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. Canadian Department of Communications Industry Canada (IC) Notice This Class B digital apparatus complies with Canadian ICES-003 and RSS-210. Cet appareil numérique de la classe B est conforme à la norme NMB-003 et CNR-210 du Canada. Industry Canada Statement This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference, and 2) This device must accept any interference received, including interference that may cause undesired operation. IMPORTANT NOTE: Radiation Exposure Statement This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. To maintain compliance with IC RF exposure compliance requirements, please follow operation instruction as documented in this manual.
Unified Services Router User Manual 219 Europe – EU Declaration of Conformity This device complies with the essential requirements of the R&TTE Directive 1999/5/EC. The following test methods have been applied in order to prove presumption of conformity with the essential requirements of the R&TTE Directive 1999/5/EC: - EN 60950-1: 2006+A11:2009 Safety of information technology equipment - EN 300 328 V1.7.1 (2006-10) Electromagnetic compatibility and Radio spectrum Matters (ERM); Wideband transmission systems; Data transmission equipment operating in the 2,4 GHz ISM band and using wide band modulation techniques; Harmonized EN covering essential requirements under article 3.2 of the R&TTE Directive - EN 301 489-17 V1.3.2 (2008-04) and EN 301 489-1 V1.8.1 (2008-04) Electromagnetic compatibility and Radio spectrum Matters (ERM); Electro Magnetic Compatibility (EMC) standard for radio equipment and services; Part 17: Specific conditions for 2,4 GHz wideband transmission systems and 5 GHz high performance RLAN equipment This device is a 2.4 GHz wideband transmission system (transceiver), intended for use in all EU member states and EFTA countries under the following conditions and/or with the following restrictions: - In Italy the end-user should apply for a license at the national spectrum authorities in order to obtain authorization to use the device for setting up outdoor radio links and/or for supplying public access to telecommunications and/or network services. - This device may not be used for setting up outdoor radio links in France and in some areas the RF output power may be limited to 10 mW EIRP in the frequency range of 2454 – 2483.5 MHz. For detailed information the enduser should contact the national spectrum authority in France.
Unified Services Router User Manual 220 Česky [Czech] [D-Link Corporation] tímto prohlašuje, že tento [DSR-500N] je ve shodě se základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES. Dansk [Danish] Undertegnede [D-Link Corporation] erklærer herved, at følgende udstyr [DSR-500N] overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF. Deutsch [German] Hiermit erklärt [D-Link Corporation], dass sich das Gerät [DSR-500N] in Übereinstimmung mit den grundlegenden Anforderungen und den übrigen einschlägigen Bestimmungen der Richtlinie 1999/5/EG befindet. Eesti [Estonian] Käesolevaga kinnitab [D-Link Corporation] seadme [DSR-500N] vastavust direktiivi 1999/5/EÜ põhinõuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele sätetele. English Hereby, [D-Link Corporation], declares that this [DSR-500N] is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. Español [Spanish] Por medio de la presente [D-Link Corporation] declara que el [DSR-500N] cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE. Ελληνική [Greek] ΜΕ ΣΗΝ ΠΑΡΟΤ΢Α [D-Link Corporation] ΔΗΛΩΝΕΙ ΟΣΙ [DSR-500N] ΢ΤΜΜΟΡΦΩΝΕΣΑΙ ΠΡΟ΢ ΣΙ΢ ΟΤ΢ΙΩΔΕΙ΢ ΑΠΑΙΣΗ΢ΕΙ΢ ΚΑΙ ΣΙ΢ ΛΟΙΠΕ΢ ΢ΥΕΣΙΚΕ΢ ΔΙΑΣΑΞΕΙ΢ ΣΗ΢ ΟΔΗΓΙΑ΢ 1999/5/ΕΚ. Français [French] Par la présente [D-Link Corporation] déclare que l'appareil [DSR-500N] est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE. Italiano [Italian] Con la presente [D-Link Corporation] dichiara che questo [DSR-500N] è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE. Latviski [Latvian] Ar šo [D-Link Corporation] deklarē, ka [DSR-500N] atbilst Direktīvas 1999/5/EK būtiskajām prasībām un citiem ar to saistītajiem noteikumiem. Lietuvių [Lithuanian] Šiuo [D-Link Corporation] deklaruoja, kad šis [DSR-500N] atitinka esminius reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas. Nederlands [Dutch] Hierbij verklaart [D-Link Corporation] dat het toestel [DSR-500N] in overeenstemming is met de essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/EG. Malti [Maltese] Hawnhekk, [D-Link Corporation], jiddikjara li dan [DSR-500N] jikkonforma mal-ħtiġijiet essenzjali u ma provvedimenti oħrajn relevanti li hemm fid-Dirrettiva 1999/5/EC. Magyar [Hungarian] Alulírott, [D-Link Corporation] nyilatkozom, hogy a [DSR-500N] megfelel a vonatkozó alapvetõ követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak. Polski [Polish] Niniejszym [D-Link Corporation] oświadcza, że [DSR-500N] jest zgodny z zasadniczymi wymogami oraz pozostałymi stosownymi postanowieniami Dyrektywy 1999/5/EC.
Unified Services Router User Manual 221 Português [Portuguese] [D-Link Corporation] declara que este [DSR-500N]está conforme com os requisitos essenciais e outras disposições da Directiva 1999/5/CE. Slovensko [Slovenian] [D-Link Corporation] izjavlja, da je ta [DSR-500N] v skladu z bistvenimi zahtevami in ostalimi relevantnimi določili direktive 1999/5/ES. Slovensky [Slovak] [D-Link Corporation] týmto vyhlasuje, že [DSR-500N] spĺňa základné požiadavky a všetky príslušné ustanovenia Smernice 1999/5/ES. Suomi [Finnish] [D-Link Corporation] vakuuttaa täten että [DSR-500N] tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen. Svenska [Swedish] Härmed intygar [D-Link Corporation] att denna [DSR-500N] står I överensstämmelse med de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv 1999/5/EG.
Unified Services Router User Manual 222 3.DSR-250N Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:  Reorient or relocate the receiving antenna.  Increase the separation between the equipment and receiver.  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. RSS-GEN 7.1.2: Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. RSS-GEN 7.1.3 You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.FCC RF Radiation Exposure Statement:1. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.This radio transmitter (identify the device by certification number, or model number if Category II) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
Unified Services Router User Manual 223 Regulatory statement (R&TTE) European standards dictate maximum radiated transmit power of 100mW EIRP and frequency range 2.400-2.4835GHz; In France, the equipment must be restricted to the 2.4465-2.4835GHz frequency range and must be restricted to indoor use. Operation of this device is subjected to the following National regulations and may be prohibited to use if certain restriction should be applied. D=0.020m is the minimum safety distance between the EUT and human body when the E-Field strength is 61V/m. Is herewith confirmed to comply with the requirements set out in the Council Directive on the Approximation of the Laws of the Member States relating to Electromagnetic Compatibility (2004/108/EC), Low-voltage Directive (2006/95/EC), the procedures given in European Council Directive 99/5/EC and 2004/104/EC. The equipment was passed. The test was performed according to the following European standards: EN 300 328 V.1.7.1 EN 301 489-1 V.1. 8.1 / EN 301 489-17 V.2.1.1 EN 62311 EN 60950-1

Navigation menu