D Link DIR601A1 Wireless N 150 Home Router User Manual Manual

D Link Corporation Wireless N 150 Home Router Manual

Manual

iD-Link DIR-601 User ManualD-Link reserves the right to revise this publication and to make changes in the content hereof without obligation to notify any person or organization of such revisions or changes.Manual RevisionsTrademarksD-Link and the D-Link logo are trademarks or registered trademarks of D-Link Corporation or its subsidiaries in the United States or other countries. All other company or product names mentioned herein are trademarks or registered trademarks of their respective companies.Copyright © 2009 by D-Link Systems, Inc.All rights reserved. This publication may not be reproduced, in whole or in part, without prior expressed written permission from D-Link Systems, Inc.Revision Date Description1.0 October 8, 2009 • Revision A1 with firmware version 1.00Preface
iiD-Link DIR-601 User ManualTable of ContentsPreface ...........................................................................iManual Revisions ..................................................... iTrademarks ............................................................... iProduct Overview ........................................................1Package Contents....................................................1System Requirements .............................................2Features ...................................................................3Hardware Overview .................................................4Connections .......................................................4LEDs ..................................................................5Installation ....................................................................6Before you Begin .....................................................6Wireless Installation Considerations ........................7Network Diagram .....................................................8Connect to Cable/DSL/Satellite Modem ..................9Connect to Another Router ....................................10Getting Started ......................................................12Configuration .............................................................13Web-based Configuration Utility ............................13Internet Connection Setup Wizard ...................14Manual Configuration .......................................19Dynamic (Cable)...........................................19Dynamic IP Address (DHCP) .......................20PPPoE (DSL) ...............................................21PPTP ............................................................23L2TP .............................................................25Static IP Address ..........................................27Wireless Settings .............................................29Manual Wireless Network Setup ..................30Network Settings ..............................................32DHCP Server Settings .................................33DHCP Reservation .......................................34Virtual Server ...................................................36Port Forwarding ...............................................38Application Rules .............................................39QoS Engine .....................................................40Network Filters .................................................41Access Control .................................................42Access Control Wizard .................................42Website Filters .................................................45Inbound Filters .................................................46Firewall Settings ...............................................47Routing ............................................................48Advanced Wireless Settings ............................49Advanced Network Settings .............................50UPnP ............................................................50Internet Ping Block .......................................50Internet Port Speed ......................................50Multicast Streams .........................................50IPv6 ..................................................................51Link-Local Connectivity ................................51Static IPv6 (Stateful) ....................................52Table of Contents
iiiD-Link DIR-601 User ManualTable of ContentsStatic IPv6 (Stateless) ..................................53DHCPv6 (Stateful) ........................................54DHCPv6 (Stateless) .....................................55IPv6 over PPPoE (Stateful) ..........................56IPv6 over PPPoE (Stateless) ........................586 to 4 Tunneling (Stateful) ............................606 to 4 Tunneling (Stateless) ..........................61IPv6 in IPv4 Tunneling (Stateful) ..................62IPv6 in IPv4 Tunneling (Stateless) ................63Administrator Settings ......................................64Time Settings ...................................................65SysLog .............................................................66E-mail Settings .................................................67System Settings ...............................................68Update Firmware .............................................69DDNS ...............................................................70System Check ..................................................71Schedules ........................................................72Device Information ...........................................73Log ...................................................................75Stats .................................................................76Internet Sessions .............................................77Routing Table ...................................................79Wireless ...........................................................80IPv6 ..................................................................81Support ............................................................82Wireless Security .......................................................83What is WPA? ........................................................83Wireless Connection Setup Wizard .......................84Add Wireless Device with WPS Wizard .................86Configure WPA-Personal (PSK) .............................87Configure WPA-Enterprise (RADIUS) ....................88Connect to a Wireless Network ................................90Using Windows Vista® ............................................90Configure WPA/WPA2 ......................................91Connect Using WCN 2.0 ..................................93Using Windows® XP ...............................................94Configure WPA-PSK ........................................95Troubleshooting .........................................................97Wireless Basics .......................................................101What is Wireless? ................................................102Tips ......................................................................104Wireless Modes ...................................................105Networking Basics ..................................................106Check your IP address ........................................106Statically Assign an IP address ...........................107Technical Specifications .........................................108Contacting Technical Support ................................109Warranty ...................................................................110Registration ..............................................................116
1D-Link DIR-601 User ManualSection 1 - Product OverviewProduct OverviewNote: Using a power supply with a different voltage rating than the one included with the DIR-601 will cause damage and void the warranty for this product.Package ContentsD-Link DIR-601 Wireless N 150 Home RouterPower AdapterEthernet CableCD-ROM
2D-Link DIR-601 User ManualSection 1 - Product OverviewNetwork Requirements • An Ethernet-based Cable or DSL modem• IEEE 802.11n-draft/g wireless clients• 10/100 EthernetWeb-based Configuration Utility RequirementsComputer with the following:• Windows®, Macintosh, or Linux-based operating system • An installed Ethernet adapterBrowser Requirements:• Internet Explorer® 6.0 and higher• Mozilla Firefox 3.0 and higher• Google™ Chrome 2.0 and higher• Apple Safari 3.0 and higherWindows® Users: Make sure you have the latest version of Java installed. Visit www.java.com to download the latest version.CD Installation Wizard RequirementsComputer with the following:• Windows® XP with Service Pack 2 or Vista®• An installed Ethernet adapter• CD-ROM driveSystem Requirements
3D-Link DIR-601 User ManualSection 1 - Product Overview• Faster Wireless Networking - The DIR-601 provides up to 150Mbps.* This capability allows users to participate in real-time activities online, such as video streaming, online gaming, and real-time audio. • Compatible with 802.11g Devices - The DIR-601 is still fully compatible with the IEEE 802.11g standard, so it can connect with existing 802.11g PCI, USB and Cardbus adapters.• Advanced Firewall Features - The Web-based user interface displays a number of advanced network management features including: • Content Filtering - Easily applied content filtering based on MAC Address, URL, and/or Domain Name.• Filter Scheduling - These filters can be scheduled to be active on certain days or for a duration of hours or minutes.• Secure Multiple/Concurrent Sessions - The DIR-601 can pass through VPN sessions. It supports multiple and concurrent IPSec and PPTP sessions, so users behind the DIR-601 can securely access corporate networks.• User-friendly Setup Wizard - Through its easy-to-use Web-based user interface, the DIR-601 lets you control what information is accessible to those on the wireless network, whether from the Internet or from your company’s server. Configure your router to your specific settings within minutes.* Maximum wireless signal rate derived from IEEE Standard 802.11g and Draft 802.11n specifications. Actual data throughput will vary. Network conditions and environmental factors, including volume of network traffic, building materials and construction, and network overhead, lower actual data throughput rate. Environmental conditions will adversely affect wireless signal range.Features
4D-Link DIR-601 User ManualSection 1 - Product OverviewHardware OverviewConnectionsPower ReceptorReceptor for the supplied power adapter.LAN Ports (1-4) Connect Ethernet devices such as computers, switches, and hubs.Reset Pressing the Reset button restores the router to its original factory default settings.Internet Port The auto MDI/MDIX Internet port is the connection for the Ethernet cable to the cable or DSL modem.
5D-Link DIR-601 User ManualSection 1 - Product OverviewWLAN LED A solid light indicates that the wireless segment is ready. This LED blinks during wireless data transmission.Internet LED A solid light indicates connection on the Internet port. This LED blinks during data transmission.Power LED A solid light indicates a proper connection to the power supply.Local Network LEDs A solid light indicates a connection to an Ethernet-enabled computer on ports 1-4. This LED blinks during data transmission.Hardware OverviewLEDs
6D-Link DIR-601 User ManualSection 2 - InstallationBefore you BeginThis section will walk you through the installation process. Placement of the router is very important. Do not place the router in an enclosed area such as a closet, cabinet, or in the attic or garage. • Please configure the router with the computer that was last connected directly to your modem. • You can only use the Ethernet port on your modem. If you were using the USB connection before using the router, then you must turn off your modem, disconnect the USB cable and connect an Ethernet cable to the Internet port on the router, and then turn the modem back on. In some cases, you may need to call your ISP to change connection types (USB to Ethernet). • If you have DSL and are connecting via PPPoE, make sure you disable or uninstall any PPPoE software such as WinPoet, Broadjump, or Enternet 300 from your computer or you will not be able to connect to the Internet.• When running the Setup Wizard from the D-Link CD, make sure the computer you are running the CD from is connected to the Internet and online or the wizard will not work. If you have disconnected any hardware, re-connect your computer back to the modem and make sure you are online.Installation
7D-Link DIR-601 User ManualSection 2 - InstallationWireless Installation ConsiderationsThe D-Link wireless router lets you access your network using a wireless connection from virtually anywhere within the operating range of your wireless network. Keep in mind, however, that the number, thickness and location of walls, ceilings, or other objects that the wireless signals must pass through, may limit the range. Typical ranges vary depending on the types of materials and background RF (radio frequency) noise in your home or business. The key to maximizing wireless range is to follow these basic guidelines:1. Keep the number of walls and ceilings between the D-Link router and other network devices to a minimum - each wall or ceiling can reduce your adapter’s range from 3-90 feet (1-30 meters.) Position your devices so that the number of walls or ceilings is minimized.2. Be aware of the direct line between network devices. A wall that is 1.5 feet thick (.5 meters), at a 45-degree angle appears to be almost 3 feet (1 meter) thick. At a 2-degree angle it looks over 42 feet (14 meters) thick! Position devices so that the signal will travel straight through a wall or ceiling (instead of at an angle) for better reception.3. Building Materials make a difference. A solid metal door or aluminum studs may have a negative effect on range. Try to position access points, wireless routers, and computers so that the signal passes through drywall or open doorways. Materials and objects such as glass, steel, metal, walls with insulation, water (fish tanks), mirrors, file cabinets, brick, and concrete will degrade your wireless signal.4. Keep your product away (at least 3-6 feet or 1-2 meters) from electrical devices or appliances that generate RF noise.5. If you are using 2.4GHz cordless phones or X-10 (wireless products such as ceiling fans, lights, and home security systems), your wireless connection may degrade dramatically or drop completely. Make sure your 2.4GHz phone base is as far away from your wireless devices as possible. The base transmits a signal even if the phone in not in use.
8D-Link DIR-601 User ManualSection 2 - InstallationNetwork Diagram
9D-Link DIR-601 User ManualSection 2 - InstallationIf you are connecting the router to a cable/DSL/satellite modem, please follow the steps below:1. Place the router in an open and central location. Do not plug the power adapter into the router. 2. Turn the power off on your modem. If there is no on/off switch, then unplug the modem’s power adapter. Shut down your computer.3. Unplug the Ethernet cable (that connects your computer to your modem) from your computer and place it into the Internet port on the router. 4. Plug an Ethernet cable into one of the four LAN ports on the router. Plug the other end into the Ethernet port on your computer.5. Turn on or plug in your modem. Wait for the modem to boot (about 30 seconds). 6. Plug the power adapter to the router and connect to an outlet or power strip. Wait about 30 seconds for the router to boot. 7. Turn on your computer. 8. Verify the link lights on the router. The power light, Internet light, and the LAN light (the port that your computer is plugged into) should be lit. If not, make sure your computer, modem, and router are powered on and verify the cable connections are correct. 9. Skip to page 12 to configure your router. Connect to Cable/DSL/Satellite Modem
10D-Link DIR-601 User ManualSection 2 - InstallationIf you are connecting the D-Link router to another router to use as a wireless access point and/or switch, you will have to do the following before connecting the router to your network:• Disable UPnP™• Disable DHCP• Change the LAN IP address to an available address on your network. The LAN ports on the router cannot accept a DHCP address from your other router.To connect to another router, please follow the steps below:1. Plug the power into the router. Connect one of your computers to the router (LAN port) using an Ethernet cable. Make sure your IP address on the computer is 192.168.0.xxx (where xxx is between 2 and 254). Please see the Networking Basics section for more information. If you need to change the settings, write down your existing settings before making any changes. In most cases, your computer should be set to receive an IP address automatically in which case you will not have to do anything to your computer.2. Open a web browser and enter http://192.168.0.1 and press Enter. When the login window appears, set the user name to Admin and leave the password box empty. Click Log In to continue.3. Click on Advanced and then click Advanced Network. Uncheck the Enable UPnP checkbox. Click Save Settings to continue. 4. Click Setup and then click Network Settings. Uncheck the Enable DHCP Server server checkbox. Click Save Settings to continue.5. Under Router Settings, enter an available IP address and the subnet mask of your network. Click Save Settings to save your settings. Use this new IP address to access the configuration utility of the router in the future. Close the browser and change your computer’s IP settings back to the original values as in Step 1.Connect to Another Router
11D-Link DIR-601 User ManualSection 2 - Installation6. Disconnect the Ethernet cable from the router and reconnect your computer to your network. 7. Connect an Ethernet cable in one of the LAN ports of the router and connect it to your other router. Do not plug anything into the Internet port of the D-Link router. 8. You may now use the other 3 LAN ports to connect other Ethernet devices and computers. To configure your wireless network, open a web browser and enter the IP address you assigned to the router. Refer to the Configuration and Wireless Security sections for more information on setting up your wireless network.
12D-Link DIR-601 User ManualSection 2 - InstallationNote: It is recommended to write down the login password on the provided CD holder.The DIR-601 includes a Quick Router Setup Wizard CD. Follow the simple steps below to run the Setup Wizard to guide you quickly through the installation process. You may manually configure your router without the wizard. Refer to the next page to manually setup your router.Insert the Quick Router Setup Wizard CD in the CD-ROM drive. The step-by-step instructions that follow are shown in Windows® XP or Vista®. The steps and screens are similar for the other Windows® operating systems.If the CD autorun function does not automatically start on your computer, go to Start > Run. In the run box type “D:\DIR601.exe” (where D: represents the drive letter of your CD-ROM drive).When the autorun screen appears, click Install Router and follow the on-screen instructions. Getting Started
13D-Link DIR-601 User ManualSection 3 - ConfigurationConfigurationThis section will show you how to configure your new D-Link wireless router using the web-based configuration utility.Web-based Configuration UtilityTo access the configuration utility, open a web-browser such as Internet Explorer and enter the IP address of the router (192.168.0.1).Select Admin from the drop-down menu and then enter your password. Leave the password blank by default.If you get a Page Cannot be Displayed error, please refer to the Troubleshooting section for assistance.
14D-Link DIR-601 User ManualSection 3 - ConfigurationInternet Connection Setup WizardOnce logged into the web interface of the router, the Setup > Internet page will appear. Click the Internet Connection Setup Wizard button to quickly configure your router using the setup wizard.If you want to enter your settings without running the wizard, click Manual Internet Configuration Wizard and skip to page 19.
15D-Link DIR-601 User ManualSection 3 - ConfigurationClick Next to continue.Create a new password and then click Next to continue.Select your time zone from the drop-down menu and then click Next to continue.
16D-Link DIR-601 User ManualSection 3 - ConfigurationIf you selected Dynamic, you may need to enter the MAC address of the computer that was last connected directly to your modem. If you are currently using that computer, click Clone Your PC’s MAC Address and then click Next to continue.The Host Name is optional but may be required by some ISPs. The default host name is the device name of the Router and may be changed.Select the type of Internet connection you use and then click Next to continue.
17D-Link DIR-601 User ManualSection 3 - ConfigurationIf you selected PPTP, enter your PPTP username and password. Click Next to continue.If you selected PPPoE, enter your PPPoE username and password. Click Next to continue.Select Static if your ISP assigned you the IP address, subnet mask, gateway, and DNS server addresses.Note: Make sure to remove your PPPoE software from your computer. The software is no longer needed and will not work through a router.
18D-Link DIR-601 User ManualSection 3 - ConfigurationIf you selected L2TP, enter your L2TP username and password. Click Next to continue.If you selected Static, enter your network settings supplied by your Internet provider. Click Next to continue.Click Connect to save your settings. Once the router is finished rebooting, click Continue. Please allow 1-2 minutes to connect.
19D-Link DIR-601 User ManualSection 3 - ConfigurationIf you opt to set up your Internet connection manually, you will be redirected to a WAN page that allows you to select your Internet type and enter the correct configuration parameters.Select your Internet connection type using the “My Internet Connection is” drop-down menu.Click the Save Settings button when you have configured the connection.Manual ConfigurationDynamic (Cable)
20D-Link DIR-601 User ManualSection 3 - ConfigurationDynamic IP Address (DHCP)Advanced Domain Name System (DNS) services enhances your Internet performance by getting you the information and web pages you are looking for faster and more reliably. In addition, it improves your overall Internet experience by correcting many common typo mistakes automatically, taking you where you intended to go and saving you valuable time.Disclaimer: D-Link makes no warranty as to the availability, reliability, functionality and operation of the Advanced DNS service or its features.The Host Name is optional but may be required by some ISPs. Check the box if you are having problems obtaining an IP address from your ISP.Enter the Primary DNS server IP address assigned by your ISP.Maximum Transmission Unit - you may need to change the MTU for optimal performance with your specific ISP. 1500 is the default MTU.The default MAC Address is set to the Internet port’s physical interface MAC address on the Broadband Router. It is not recommended that you change the default MAC address unless required by your ISP. You can use the Clone Your PC’s MAC Address button to replace the Internet port’s MAC address with the MAC address of your Ethernet card.Enable Advanced DNS Service:Host Name:MAC Address:DNS Addresses:MTU:Use Unicasting:
21D-Link DIR-601 User ManualSection 3 - ConfigurationSelect Dynamic IP (DHCP) to obtain IP Address information automatically from your ISP. Select this option if your ISP does not give you any IP numbers to use. This option is commonly used for Cable modem services. Advanced Domain Name System (DNS) services enhances your Internet performance by getting you the information and web pages you are looking for faster and more reliably. In addition, it improves your overall Internet experience by correcting many common typo mistakes automatically, taking you where you intended to go and saving you valuable time.Disclaimer: D-Link makes no warranty as to the availability, reliability, functionality and operation of the Advanced DNS service or its features.Select Static if your ISP assigned you the IP address, subnet mask, gateway, and DNS server addresses. In most cases, select Dynamic.Enter the IP address (Static PPPoE only).Enter your PPPoE user name.Enter your PPPoE password and then retype the password in the next box.My Internet Connection:Enable Advanced DNS Service:Address Mode:IP Address:User Name:Password:PPPoE (DSL)Choose PPPoE (Point to Point Protocol over Ethernet) if your ISP uses a PPPoE connection. Your ISP will provide you with a username and password. This option is typically used for DSL services. Make sure to remove your PPPoE software from your computer. The software is no longer needed and will not work through a router.
22D-Link DIR-601 User ManualSection 3 - ConfigurationEnter the ISP Service Name (optional).Select either Always-on, On-Demand, or Manual.Enter a maximum idle time during which the Internet connection is maintained during inactivity. To disable this feature, enable Auto-reconnect.Enter the Primary and Secondary DNS Server Addresses (Static PPPoE only).Maximum Transmission Unit - you may need to change the MTU for optimal performance with your specific ISP. 1492 is the default MTU.The default MAC Address is set to the Internet port’s physical interface MAC address on the Broadband Router. It is not recommended that you change the default MAC address unless required by your ISP. You can use the Clone Your PC’s MAC Address button to replace the Internet port’s MAC address with the MAC address of your Ethernet card.Service Name:Reconnection Mode:Maximum Idle Time:DNS Addresses:MTU:MAC Address:
23D-Link DIR-601 User ManualSection 3 - ConfigurationSelect Dynamic IP (DHCP) to obtain IP Address information automatically from your ISP. Select this option if your ISP does not give you any IP numbers to use. This option is commonly used for Cable modem services.Advanced Domain Name System (DNS) services enhances your Internet performance by getting you the information and web pages you are looking for faster and more reliably. In addition, it improves your overall Internet experience by correcting many common typo mistakes automatically, taking you where you intended to go and saving you valuable time.Disclaimer: D-Link makes no warranty as to the availability, reliability, functionality and operation of the Advanced DNS service or its features.Select Static if your ISP assigned you the IP address, subnet mask, gateway, and DNS server addresses. In most cases, select Dynamic.Enter the IP address (Static PPTP only).Enter the Primary and Secondary DNS Server Addresses (Static PPTP only).Enter the Gateway IP Address provided by your ISP.Enter the Server IP provided by your ISP (optional).My Internet Connection:Enabled Advanced DNS Service:Address Mode:PPTP IP Address:PPTP Subnet Mask:PPTP Gateway:PPTP Server IP:PPTPChoose PPTP (Point-to-Point-Tunneling Protocol ) if your ISP uses a PPTP connection. Your ISP will provide you with a username and password. This option is typically used for DSL services.
24D-Link DIR-601 User ManualSection 3 - ConfigurationEnter your PPTP username.Enter your PPTP password and then retype the password in the next box.Select either Always-on, On-Demand, or Manual.Enter a maximum idle time during which the Internet connection is maintained during inactivity. To disable this feature, enable Auto-reconnect.The DNS server information will be supplied by your ISP (Internet Service Provider.)Maximum Transmission Unit - you may need to change the MTU for optimal performance with your specific ISP (1400 is the default MTU).The default MAC Address is set to the Internet port’s physical interface MAC address on the Broadband Router. It is not recommended that you change the default MAC address unless required by your ISP. You can use the Clone Your PC’s MAC Address button to replace the Internet port’s MAC address with the MAC address of your Ethernet card.Username:Password: Reconnect Mode:Maximum Idle Time:DNS Servers:MTU:MAC Address:
25D-Link DIR-601 User ManualSection 3 - ConfigurationSelect Dynamic IP (DHCP) to obtain IP Address information automatically from your ISP. Select this option if your ISP does not give you any IP numbers to use. This option is commonly used for Cable modem services.Advanced Domain Name System (DNS) services enhances your Internet performance by getting you the information and web pages you are looking for faster and more reliably. In addition, it improves your overall Internet experience by correcting many common typo mistakes automatically, taking you where you intended to go and saving you valuable time.Disclaimer: D-Link makes no warranty as to the availability, reliability, functionality and operation of the Advanced DNS service or its features. Select Static if your ISP assigned you the IP address, subnet mask, gateway, and DNS server addresses. In most cases, select Dynamic.Enter the L2TP IP address supplied by your ISP (Static only).Enter the Subnet Mask supplied by your ISP (Static only).Enter the Gateway IP Address provided by your ISP.My Internet Connection:Enabled Advanced DNS Service: Address Mode:L2TP IP Address:L2TP Subnet Mask:L2TP Gateway:L2TPChoose L2TP (Layer 2 Tunneling Protocol) if your ISP uses a L2TP connection. Your ISP will provide you with a username and password. This option is typically used for DSL services.
26D-Link DIR-601 User ManualSection 3 - ConfigurationMTU:Clone MAC Address:Maximum Transmission Unit - you may need to change the MTU for optimal performance with your specific ISP. 1400 is the default MTU.The default MAC Address is set to the Internet port’s physical interface MAC address on the Broadband Router. It is not recommended that you change the default MAC address unless required by your ISP. You can use the Clone Your PC’s MAC Address button to replace the Internet port’s MAC address with the MAC address of your Ethernet card.L2TP Server IP:Username:Password:Reconnect Mode:Maximum Idle Time: DNS Servers:Enter the Server IP provided by your ISP (optional).Enter your L2TP username.Enter your L2TP password and then retype the password in the next box.Select either Always-on, On-Demand, or Manual.Enter a maximum idle time during which the Internet connection is maintained during inactivity. To disable this feature, enable Auto-reconnect.Enter the Primary and Secondary DNS Server Addresses (Static L2TP only).
27D-Link DIR-601 User ManualSection 3 - ConfigurationSelect Dynamic IP (DHCP) to obtain IP Address information automatically from your ISP. Select this option if your ISP does not give you any IP numbers to use. This option is commonly used for Cable modem services.Advanced Domain Name System (DNS) services enhances your Internet performance by getting you the information and web pages you are looking for faster and more reliably. In addition, it improves your overall Internet experience by correcting many common typo mistakes automatically, taking you where you intended to go and saving you valuable time.Disclaimer: D-Link makes no warranty as to the availability, reliability, functionality and operation of the Advanced DNS service or its features. Enter the IP address assigned by your ISP.Enter the Subnet Mask assigned by your ISP.Enter the Gateway assigned by your ISP.The DNS server information will be supplied by your ISP (Internet Service Provider.)Maximum Transmission Unit - you may need to change the MTU for optimal performance with your specific ISP (1500 is the default MTU).My Internet Connection:Enabled Advanced DNS Service: IP Address:Subnet Mask:Default Gateway:DNS Servers:MTU:Static IP AddressSelect Static IP Address if all the Internet port’s IP information is provided to you by your ISP. You will need to enter in the IP address, subnet mask, gateway address, and DNS address(es) provided to you by your ISP. Each IP address entered in the fields must be in the appropriate IP form, which are four octets separated by a dot (x.x.x.x). The Router will not accept the IP address if it is not in this format.
28D-Link DIR-601 User ManualSection 3 - ConfigurationMAC Address: The default MAC Address is set to the Internet port’s physical interface MAC address on the Broadband Router. It is not recommended that you change the default MAC address unless required by your ISP. You can use the Clone Your PC’s MAC Address button to replace the Internet port’s MAC address with the MAC address of your Ethernet card.
29D-Link DIR-601 User ManualSection 3 - ConfigurationWireless SettingsIf you want to configure the wireless settings on your router using the wizard, click Wireless Connection Setup Wizard and refer to page 81.Click Add Wireless Device with WPS if you want to add a wireless device using Wi-Fi Protected Setup (WPS) and refer to page 83.If you want to manually configure the wireless settings on your router click Manual Wireless Network Setup and refer to the next page.
30D-Link DIR-601 User ManualSection 3 - ConfigurationManual Wireless Network SetupCheck the box to enable the wireless function. If you do not want to use wireless, uncheck the box to disable all the wireless functions. Click Add New to create your own time schedule to enable the wireless function. Service Set Identifier (SSID) is the name of your wireless network. Create a name using up to 32 characters. The SSID is case-sensitive.Select one of the following:802.11g Only - Select if all of your wireless clients are 802.11g.802.11n Only - Select only if all of your wireless clients are 802.11n.Mixed 802.11n and 802.11g - Select if you are using a mix of 802.11n and 802.11g wireless clients.The Auto Channel Scan setting can be selected to allow the DIR-601 to choose the channel with the least amount of interference.Indicates the channel setting for the DIR-601. By default the channel is set to 6. The Channel can be changed to fit the channel setting for an existing wireless network or to customize the wireless network. If you enable Auto Channel Scan, this option will be greyed out.Select the Channel Width:Auto 20/40 - Select if you are using both 802.11n and non-802.11n wireless devices.20MHz - Select if you are not using any 802.11n wireless clients. This is the default setting. 40MHz - Select if you are using only 802.11n wireless clients. Enable Wireless:Wireless Network Name:802.11 Mode:Enable Auto Channel Scan:Wireless Channel:Channel Width:
31D-Link DIR-601 User ManualSection 3 - ConfigurationSelect Invisible if you do not want the SSID of your wireless network to be broadcasted by the DIR-601. If Invisible is selected, the SSID of the DIR-601 will not be seen by Site Survey utilities so your wireless clients will have to know the SSID of your DIR-601 in order to connect to it.Refer to page 78 for more information regarding wireless security.Visibility Status:Wireless Security:
32D-Link DIR-601 User ManualSection 3 - ConfigurationThis section will allow you to change the local network settings of the router and to configure the DHCP settings.Network SettingsEnter the IP address of the router. The default IP address is 192.168.0.1.If you change the IP address, once you click Apply, you will need to enter the new IP address in your browser to get back into the configuration utility.Enter the Subnet Mask. The default subnet mask is 255.255.255.0.Enter the Domain name (Optional).Uncheck the box to transfer the DNS server information from your ISP to your computers. If checked, your computers will use the router for a DNS server.IP Address:Subnet Mask:Local Domain:Enable DNS Relay:
33D-Link DIR-601 User ManualSection 3 - ConfigurationCheck this box to enable the DHCP server on your router. Uncheck to disable this function.Enter the starting and ending IP addresses for the DHCP server’s IP assignment.Note: If you statically (manually) assign IP addresses to your computers or devices, make sure the IP addresses are outside of this range or you may have an IP conflict. The length of time for the IP address lease. Enter the Lease time in minutes.Enable this function to ensure compatibility with some DHCP clients.Enable DHCP Server:DHCP IP Address Range:Lease Time:Always Broadcast:DHCP Server SettingsDHCP stands for Dynamic Host Control Protocol. The DIR-601 has a built-in DHCP server. The DHCP Server will automatically assign an IP address to the computers on the LAN/private network. Be sure to set your computers to be DHCP clients by setting their TCP/IP settings to “Obtain an IP Address Automatically.” When you turn your computers on, they will automatically load the proper TCP/IP settings provided by the DIR-601. The DHCP Server will automatically allocate an unused IP address from the IP address pool to the requesting computer. You must specify the starting and ending address of the IP address pool.
34D-Link DIR-601 User ManualSection 3 - ConfigurationDHCP ReservationIf you want a computer or device to always have the same IP address assigned, you can create a DHCP reservation. The router will assign the IP address only to that computer or device. Note: This IP address must be within the DHCP IP Address Range.Check this box to enable the reservation.Enter the computer name or select from the drop-down menu and click <<.Enter the IP address you want to assign to the computer or device. This IP Address must be within the DHCP IP Address Range.Enter the MAC address of the computer or device.If you want to assign an IP address to the computer you are currently on, click this button to populate the fields. Click Save to save your entry. You must click Save Settings at the top to activate your reservations. In this section you can see what LAN devices are currently leasing IP addresses.Click Revoke to cancel the lease for a specific LAN device and free an entry in the lease table. Do this only if the device no longer needs the leased IP address, because, for example, it has been removed from the network.Enable:Computer Name:IP Address:MAC Address:Copy Your PC’s MAC Address:Save:Number of Dynamic DHCP Clients:Revoke:
35D-Link DIR-601 User ManualSection 3 - ConfigurationReserve:Note: The Revoke option will not disconnect a PC with a current network session from the network; you would need to use MAC Address Filter to do that. Revoke will only free up a DHCP Address for the very next requester. If the previous owner is still available, those two devices may both receive an IP Address Conflict error, or the second device may still not receive an IP Address; in that case, you may still need to extend the “DHCP IP Address Range” to address the issue, it is located in the DHCP Server section. The Reserve option converts this dynamic IP allocation into a DHCP Reservation and adds the corresponding entry to the DHCP Reservations List.
36D-Link DIR-601 User ManualSection 3 - ConfigurationThe DIR-601 can be configured as a virtual server so that remote users accessing Web or FTP services via the public IP address can be automatically redirected to local servers in the LAN (Local Area Network). The DIR-601 firewall feature filters out unrecognized packets to protect your LAN network so all computers networked with the DIR-601 are invisible to the outside world. If you wish, you can make some of the LAN computers accessible from the Internet by enabling Virtual Server. Depending on the requested service, the DIR-601 redirects the external service request to the appropriate server within the LAN network. The DIR-601 is also capable of port-redirection meaning incoming traffic to a particular port may be redirected to a different port on the server computer.Each virtual service that is created will be listed at the bottom of the screen in the Virtual Servers List. There are pre-defined virtual services already in the table. You may use them by enabling them and assigning the server IP to use that particular virtual service.For a list of ports for common applications, please visit http://support.dlink.com/faq/view.asp?prod_id=1191.Virtual Server
37D-Link DIR-601 User ManualSection 3 - ConfigurationThis will allow you to open a single port. If you would like to open a range of ports, refer to the next page.Enter a name for the rule or select an application from the drop-down menu. Select an application and click << to populate the fields.Enter the IP address of the computer on your local network that you want to allow the incoming service to. If your computer is receiving an IP address automatically from the router (DHCP), you computer will be listed in the “Computer Name” drop-down menu. Select your computer and click <<. Enter the port that you want to open next to Private Port and Public Port. The private and public ports are usually the same. The public port is the port seen from the Internet side, and the private port is the port being used by the application on the computer within your local network.Select TCP, UDP, or Both from the drop-down menu.Select Allow All (most common) or a created Inbound filter. You may create your own inbound filters in the Advanced > Inbound Filter page.The schedule of time when the Virtual Server Rule will be enabled. The schedule may be set to Always, which will allow the particular service to always be enabled. You can create your own times in the Tools > Schedules section.Name:IP Address:Private Port/Public Port:Protocol Type:Inbound Filter:Schedule:
38D-Link DIR-601 User ManualSection 3 - ConfigurationThis will allow you to open a single port or a range of ports.Port ForwardingEnter a name for the rule or select an application from the drop-down menu. Select an application and click << to populate the fields.Enter the IP address of the computer on your local network that you want to allow the incoming service to. If your computer is receiving an IP address automatically from the router (DHCP), you computer will be listed in the “Computer Name” drop-down menu. Select your computer and click <<. Enter the TCP and/or UDP port or ports that you want to open. You can enter a single port or a range of ports. Separate ports with a common.Example: 24,1009,3000-4000Select Allow All (most common) or a created Inbound filter. You may create your own inbound filters in the Advanced > Inbound Filter page.The schedule of time when the Virtual Server Rule will be enabled. The schedule may be set to Always, which will allow the particular service to always be enabled. You can create your own times in the Tools > Schedules section.Name:IP Address:TCP/UDP:Inbound Filter:Schedule:
39D-Link DIR-601 User ManualSection 3 - ConfigurationEnter a name for the rule. You may select a pre-defined application from the drop-down menu and click <<.This is the port used to trigger the application. It can be either a single port or a range of ports.Select the protocol of the trigger port (TCP, UDP, or Both).This is the port number on the Internet side that will be used to access the application. You may define a single port or a range of ports. You can use a comma to add multiple ports or port ranges.Select the protocol of the firewall port (TCP, UDP, or Both).The schedule of time when the Application Rule will be enabled. The schedule may be set to Always, which will allow the particular service to always be enabled. You can create your own times in the Tools > Schedules section.Name:Trigger:Traffic Type:Firewall:Traffic Type:Schedule:Application RulesSome applications require multiple connections, such as Internet gaming, video conferencing, Internet telephony and others. These applications have difficulties working through NAT (Network Address Translation). Special Applications makes some of these applications work with the DIR-601. If you need to run applications that require multiple connections, specify the port normally associated with an application in the “Trigger Port” field, select the protocol type as TCP or UDP, then enter the firewall (public) ports associated with the trigger port to open them for inbound traffic.The DIR-601 provides some predefined applications in the table on the bottom of the web page. Select the application you want to use and enable it.
40D-Link DIR-601 User ManualSection 3 - ConfigurationQoS EngineThis option is disabled by default. Enable this option for better performance and experience with online games and other interactive applications, such as VoIP.This option is enabled by default when the QoS Engine option is enabled. This option will allow your router to automatically determine the uplink speed of your Internet connection.This displays the detected uplink speed.The speed at which data can be transferred from the router to your ISP. This is determined by your ISP. ISP’s offer speed as a download/upload pair. For example, 1.5Mbits/284Kbits. Using this example, you would enter 284. Alternatively you can test your uplink speed with a service such as www.dslreports.com.Enable QoS Engine:Automatic Uplink Speed:Measured Uplink Speed:Manual Uplink Speed:The QoS Engine option helps improve your network gaming performance by prioritizing applications. By default the QoS Engine settings are disabled and application priority is not classified automatically.
41D-Link DIR-601 User ManualSection 3 - ConfigurationNetwork FiltersSelect Turn MAC Filtering Off, allow MAC addresses listed below, or deny MAC addresses listed below from the drop-down menu. Enter the MAC address you would like to filter.To find the MAC address on a computer, please refer to the Networking Basics section in this manual. Select a DHCP client from the drop-down menu and click << to copy that MAC Address. Configure MAC Filtering:MAC Address:DHCP Client:Use MAC (Media Access Control) Filters to allow or deny LAN (Local Area Network) computers by their MAC addresses from accessing the Network. You can either manually add a MAC address or select the MAC address from the list of clients that are currently connected to the Broadband Router.
42D-Link DIR-601 User ManualSection 3 - ConfigurationAccess ControlCheck the Enable Access Control check box and click the Add Policy button to start the Access Control Wizard. Add Policy:The Access Control section allows you to control access in and out of your network. Use this feature as Parental Controls to only grant access to approved sites, limit web access based on time or dates, and/or block access from applications like P2P utilities or games.Click Next to continue with the wizard.Access Control Wizard
43D-Link DIR-601 User ManualSection 3 - ConfigurationEnter a name for the policy and then click Next to continue.Select a schedule (I.E. Always) from the drop-down menu and then click Next to continue.Enter the following information and then click Next to continue.• Address Type - Select IP address, MAC address, or Other Machines.• IP Address - Enter the IP address of the computer you want to apply the rule to.
44D-Link DIR-601 User ManualSection 3 - ConfigurationSelect the filtering method and then click Next to continue.Enter the rule: Enable - Check to enable the rule. Name - Enter a name for your rule. Dest IP Start - Enter the starting IP address. Dest IP End - Enter the ending IP address. Protocol - Select the protocol. Dest Port Start - Enter the starting port number. Dest Port End - Enter the ending port number.To enable web logging, click Enable.Click Save to save the access control rule.
45D-Link DIR-601 User ManualSection 3 - ConfigurationSelect Deny or Allow computers access to only these sites.Click to delete all entries in the list.Enter the keywords or URLs that you want to allow or deny.Configure Website Filter Below:Clear the list below:Website URL/Domain:Website FiltersWebsite Filters are used to allow you to set up a list of allowed Web sites that can be used by multiple users through the network. To use this feature select to Allow or Deny, enter the domain or website and click Add, and then click Save Settings. You must also select Apply Web Filter under the Access Control section (page 40).
46D-Link DIR-601 User ManualSection 3 - ConfigurationEnter a name for the inbound filter rule.Select Allow or Deny.Check to enable rule.Enter the starting IP address. Enter 0.0.0.0 if you do not want to specify an IP range.Enter the ending IP address. Enter 255.255.255.255 if you do not want to specify and IP range.Click the Save button to apply your settings. You must click Save Settings at the top to save the settings.This section will list any rules that are created. You may click the Edit icon to change the settings or enable/disable the rule, or click the Delete icon to remove the rule.Name:Action:Enable:Source IP Start:Source IP End:Save:Inbound Filter Rules List:The Inbound Filter option is an advanced method of controlling data received from the Internet. With this feature you can configure inbound data filtering rules that control data based on an IP address range. Inbound Filters can be used with Virtual Server, Port Forwarding, or Remote Administration features.Inbound Filters
47D-Link DIR-601 User ManualSection 3 - ConfigurationSPI (Stateful Packet Inspection, also known as dynamic packet filtering) helps to prevent cyber attacks by tracking more state per session. It validates that the traffic passing through the session conforms to the protocol.Select one of the following for TCP and UDP ports:Endpoint Independent - Any incoming traffic sent to an open port will be forwarded to the application that opened the port. The port will close if idle for 5 minutes.Address Restricted - Incoming traffic must match the IP address of the outgoing connection.Address + Port Restriction - Incoming traffic must match the IP address and port of the outgoing connection.Enable this option to provide protection from certain kinds of “spoofing” attacks.If an application has trouble working from behind the router, you can expose one computer to the Internet and run the application on that computer.Note: Placing a computer in the DMZ may expose that computer to a variety of security risks. Use of this option is only recommended as a last resort.Specify the IP address of the computer on the LAN that you want to have unrestricted Internet communication. If this computer obtains its IP address automatically using DHCP, be sure to make a static reservation on the System > Network Settings page so that the IP address of the DMZ machine does not change.Enable SPI:NAT Endpoint Filtering:Enable Anti-Spoof Checking:Enable DMZ Host:IP Address:Firewall SettingsA firewall protects your network from the outside world. The D-Link DIR-601 offers a firewall type functionality. The SPI feature helps prevent cyber attacks. Sometimes you may want a computer exposed to the outside world for certain types of applications. If you choose to expose a computer, you can enable DMZ. DMZ is short for Demilitarized Zone. This option will expose the chosen computer completely to the outside world.
48D-Link DIR-601 User ManualSection 3 - ConfigurationRoutingEnter the IP address of packets that will take this route.Enter the netmask of the route, please note that the octets must match your destination IP address.Enter your next hop gateway to be taken if this route is used.The route metric is a value from 1 to 16 that indicates the cost of using this route. A value 1 is the lowest cost and 15 is the highest cost. Select the interface that the IP packet must use to transit out of the router when this route is used. Destination IP:Netmask:Gateway:Metric:Interface:The Routing option is an advanced method of customizing specific routes of data through your network.
49D-Link DIR-601 User ManualSection 3 - ConfigurationSet the transmit power of the antennas.Beacons are packets sent by an Access Point to synchronize a wireless network. Specify a value. 100 is the default setting and is recommended. This value should remain at its default setting of 2432. If inconsistent data flow is a problem, only a minor modification should be made.The fragmentation threshold, which is specified in bytes, determines whether packets will be fragmented. Packets exceeding the 2346 byte setting will be fragmented before transmission. 2346 is the default setting. (Delivery Traffic Indication Message) 3 is the default setting. A DTIM is a countdown informing clients of the next window for listening to broadcast and multicast messages.This enables 802.11d operation. 802.11d is a wireless specification developed to allow implementation of wireless networks in countries that cannot use the 802.11 standard. This feature should only be enabled if you are in a country that requires it.WMM is QoS for your wireless network. This will improve the quality of video and voice applications for your wireless clients.Check this box to reduce the guard interval time therefore increasing the data capacity. However, it’s less reliable and may create higher data loss.Transmit Power:Beacon Period:RTS Threshold:Fragmentation Threshold:DTIM Interval:WLAN Partition:WMM Enable:Short GI:Advanced Wireless Settings
50D-Link DIR-601 User ManualSection 3 - ConfigurationTo use the Universal Plug and Play (UPnP™) feature click on Enable UPnP. UPNP provides compatibility with networking equipment, software and peripherals.Unchecking the box will not allow the DIR-601 to respond to pings. Blocking the Ping may provide some extra security from hackers. Check the box to allow the Internet port to be “pinged”.You may set the port speed of the Internet port to 10Mbps, 100Mbps, or Auto. Some older cable or DSL modems may require you to set the port speed to 10Mbps.Check the box to allow multicast traffic to pass through the router from the Internet.UPnP Settings:WAN Ping:WAN Port Speed:Multicast Streams:Advanced Network Settings
51D-Link DIR-601 User ManualSection 3 - ConfigurationIPv6Select Link-Local Only from the drop-down menu.Displays the IPv6 address of the router.My IPv6 Connection:LAN IPv6 Address Settings:Link-Local Connectivity
52D-Link DIR-601 User ManualSection 3 - ConfigurationStatic IPv6 (Stateful)Select Static IPv6 from the drop-down menu.Enter the address settings supplied by your Internet provider (ISP). Enter the LAN (local) IPv6 address for the router. Displays the Router’s LAN Link-Local Address.Check to enable the Autoconfiguration feature.Select Stateful (DHCPv6) or Stateless. Refer to the next page for Stateless.Enter the start IPv6 Address for the DHCPv6 range for your local computers.Enter the end IPv6 Address for the DHCPv6 range for your local computers.Enter the IPv6 Address Lifetime (in minutes).My IPv6 Connection:WAN IPv6 Address Settings:LAN IPv6 Address:LAN Link-Local Address:Enable Autoconfiguration:Autoconfiguration Type:IPv6 Address Range Start:IPv6 Address Range End:IPv6 Address Lifetime:
53D-Link DIR-601 User ManualSection 3 - ConfigurationStatic IPv6 (Stateless)Select Static IPv6 from the drop-down menu.Enter the address settings supplied by your Internet provider (ISP). Enter the LAN (local) IPv6 address for the router. Displays the Router’s LAN Link-Local Address.Check to enable the Autoconfiguration feature.Select Stateless. Refer to the previous page for Stateful.Enter the Router Advertisement Lifetime (in minutes).My IPv6 Connection:WAN IPv6 Address Settings:LAN IPv6 Address:LAN Link-Local Address:Enable Autoconfiguration:Autoconfiguration Type:Router Advertisement Lifetime:
54D-Link DIR-601 User ManualSection 3 - ConfigurationDHCPv6 (Stateful)Select DHCPv6 from the drop-down menu.Select either Obtain DNS server address automatically or Use the following DNS Address.Enter the primary and secondary DNS server addresses. Enter the LAN (local) IPv6 address for the router. Displays the Router’s LAN Link-Local Address.Check to enable the Autoconfiguration feature.Select Stateful (DHCPv6) or Stateless. Refer to the next page for Stateless.Enter the start IPv6 Address for the DHCPv6 range for your local computers.Enter the end IPv6 Address for the DHCPv6 range for your local computers.Enter the IPv6 Address Lifetime (in minutes).My IPv6 Connection:IPv6 DNS Settings:Primary/Secondary DNS Address:LAN IPv6 Address:LAN Link-Local Address:Enable Autoconfiguration:Autoconfiguration Type:IPv6 Address Range Start:IPv6 Address Range End:IPv6 Address Lifetime:
55D-Link DIR-601 User ManualSection 3 - ConfigurationDHCPv6 (Stateless)Select DHCPv6 from the drop-down menu.Select either Obtain DNS server address automatically or Use the following DNS Address.Enter the primary and secondary DNS server addresses. Enter the LAN (local) IPv6 address for the router. Displays the Router’s LAN Link-Local Address.Check to enable the Autoconfiguration feature.Select Stateless. Refer to the previous page for Stateful.Enter the Router Advertisement Lifetime (in minutes).My IPv6 Connection:IPv6 DNS Settings:Primary/Secondary DNS Address:LAN IPv6 Address:LAN Link-Local Address:Enable Autoconfiguration:Autoconfiguration Type:Router Advertisement Lifetime:
56D-Link DIR-601 User ManualSection 3 - ConfigurationIPv6 over PPPoE (Stateful)Select PPPoE from the drop-down menu.Enter the PPPoE account settings supplied by your Internet provider (ISP). Select Static if your ISP assigned you the IP address, subnet mask, gateway, and DNS server addresses. In most cases, select Dynamic.Enter the IP address (Static PPPoE only).Enter your PPPoE user name.Enter your PPPoE password and then retype the password in the next box.Enter the ISP Service Name (optional).Select either Always-on, On-Demand, or Manual.Enter a maximum idle time during which the Internet connection is maintained during inactivity. To disable this feature, enable Auto-reconnect.Select either Obtain DNS server address automatically or Use the following DNS Address.Enter the primary and secondary DNS server addresses. Enter the LAN (local) IPv6 address for the router. Displays the Router’s LAN Link-Local Address.My IPv6 Connection:PPPoE:Address Mode:IP Address:User Name:Password:Service Name:Reconnection Mode:Maximum Idle Time:IPv6 DNS Settings:Primary/Secondary DNS Address:LAN IPv6 Address:LAN Link-Local Address:
57D-Link DIR-601 User ManualSection 3 - ConfigurationEnable Autoconfiguration:Autoconfiguration Type:IPv6 Address Range Start:IPv6 Address Range End:IPv6 Address Lifetime:Check to enable the Autoconfiguration feature.Select Stateful (DHCPv6) or Stateless. Refer to the next page for Stateless.Enter the start IPv6 Address for the DHCPv6 range for your local computers.Enter the end IPv6 Address for the DHCPv6 range for your local computers.Enter the IPv6 Address Lifetime (in minutes).
58D-Link DIR-601 User ManualSection 3 - ConfigurationIPv6 over PPPoE (Stateless)Select PPPoE from the drop-down menu.Enter the PPPoE account settings supplied by your Internet provider (ISP). Select Static if your ISP assigned you the IP address, subnet mask, gateway, and DNS server addresses. In most cases, select Dynamic.Enter the IP address (Static PPPoE only).Enter your PPPoE user name.Enter your PPPoE password and then retype the password in the next box.Enter the ISP Service Name (optional).Select either Always-on, On-Demand, or Manual.Enter a maximum idle time during which the Internet connection is maintained during inactivity. To disable this feature, enable Auto-reconnect.Select either Obtain DNS server address automatically or Use the following DNS Address.Enter the primary and secondary DNS server addresses. Enter the LAN (local) IPv6 address for the router. Displays the Router’s LAN Link-Local Address.My IPv6 Connection:PPPoE:Address Mode:IP Address:User Name:Password:Service Name:Reconnection Mode:Maximum Idle Time:IPv6 DNS Settings:Primary/Secondary DNS Address:LAN IPv6 Address:LAN Link-Local Address:
59D-Link DIR-601 User ManualSection 3 - ConfigurationEnable Autoconfiguration:Autoconfiguration Type:Router Advertisement Lifetime:Check to enable the Autoconfiguration feature.Select Stateful (DHCPv6) or Stateless. Enter the Router Advertisement Lifetime (in minutes).
60D-Link DIR-601 User ManualSection 3 - Configuration6 to 4 Tunneling (Stateful)Select 6 to 4 from the drop-down menu.Enter the IPv6 settings supplied by your Internet provider (ISP). Enter the primary and secondary DNS server addresses. Enter the LAN (local) IPv6 address for the router. Displays the Router’s LAN Link-Local Address.Check to enable the Autoconfiguration feature.Select Stateful (DHCPv6) or Stateless. Refer to the next page for Stateless.Enter the start IPv6 Address for the DHCPv6 range for your local computers.Enter the end IPv6 Address for the DHCPv6 range for your local computers.Enter the IPv6 Address Lifetime (in minutes).My IPv6 Connection:6 to 4 Settings:Primary/Secondary DNS Address:LAN IPv6 Address:LAN Link-Local Address:Enable Autoconfiguration:Autoconfiguration Type:IPv6 Address Range Start:IPv6 Address Range End:IPv6 Address Lifetime:
61D-Link DIR-601 User ManualSection 3 - Configuration6 to 4 Tunneling (Stateless)Select 6 to 4 from the drop-down menu.Enter the IPv6 settings supplied by your Internet provider (ISP). Enter the primary and secondary DNS server addresses. Enter the LAN (local) IPv6 address for the router. Displays the Router’s LAN Link-Local Address.Check to enable the Autoconfiguration feature.Select Stateless. Refer to the previous page for Stateful.Enter the Router Advertisement Lifetime (in minutes).My IPv6 Connection:6 to 4 Settings:Primary/Secondary DNS Address:LAN IPv6 Address:LAN Link-Local Address:Enable Autoconfiguration:Autoconfiguration Type:Router Advertisement Lifetime:
62D-Link DIR-601 User ManualSection 3 - ConfigurationIPv6 in IPv4 Tunneling (Stateful)Select IPv6 in IPv4 Tunnel from the drop-down menu.Enter the settings supplied by your Internet provider (ISP). Enter the LAN (local) IPv6 address for the router. Displays the Router’s LAN Link-Local Address.Check to enable the Autoconfiguration feature.Select Stateless. Refer to the previous page for Stateful.Enter the Router Advertisement Lifetime (in minutes).My IPv6 Connection:IPv6 in IPv4 Tunnel Settings:LAN IPv6 Address:LAN Link-Local Address:Enable Autoconfiguration:Autoconfiguration Type:Router Advertisement Lifetime:
63D-Link DIR-601 User ManualSection 3 - ConfigurationIPv6 in IPv4 Tunneling (Stateless)Select IPv6 in IPv4 Tunnel from the drop-down menu.Enter the settings supplied by your Internet provider (ISP). Enter the LAN (local) IPv6 address for the router. Displays the Router’s LAN Link-Local Address.Check to enable the Autoconfiguration feature.Select Stateful (DHCPv6) or Stateless. Refer to the next page for Stateless.Enter the start IPv6 Address for the DHCPv6 range for your local computers.Enter the end IPv6 Address for the DHCPv6 range for your local computers.Enter the IPv6 Address Lifetime (in minutes).My IPv6 Connection:IPv6 in IPv4 Tunnel Settings:LAN IPv6 Address:LAN Link-Local Address:Enable Autoconfiguration:Autoconfiguration Type:IPv6 Address Range Start:IPv6 Address Range End:IPv6 Address Lifetime:
64D-Link DIR-601 User ManualSection 3 - ConfigurationEnter a new password for the Administrator Login Name. The administrator can make changes to the settings.Enter the new password for the User login. If you login as the User, you can only see the settings, but cannot change them.Enter a name for the DIR-601 router.Enables a challenge-response test to require users to type letters or numbers from a distorted image displayed on the screen to prevent online hackers and unauthorized users from gaining access to your router’s network settings. Remote management allows the DIR-601 to be configured from the Internet by a web browser. A username and password is still required to access the Web-Management interface. In general, only a member of your network can browse the built-in web pages to perform Administrator tasks. This feature enables you to perform Administrator tasks from the remote (Internet) host.The port number used to access the DIR-601.Example: http://x.x.x.x:8080 whereas x.x.x.x is the Internet IP address of the DIR-601 and 8080 is the port used for the Web Management interface.This section will list any rules that are created. You may click the Edit icon to change the settings or enable/disable the rule, or click the Delete icon to remove the rule.Admin Password:User Password:Gateway Name:Enable Graphical Authentication:Remote Management:Remote Admin Port:Remote Admin Inbound Filter:Administrator SettingsThis page will allow you to change the Administrator and User passwords. You can also enable Remote Management. There are two accounts that can access the management interface through the web browser. The accounts are admin and user. Admin has read/write access while user has read-only access. User can only view the settings but cannot make any changes. Only the admin account has the ability to change both admin and user account passwords.
65D-Link DIR-601 User ManualSection 3 - ConfigurationTime SettingsSelect the Time Zone from the drop-down menu.To select Daylight Saving time manually, select enabled or disabled, and enter a start date and an end date for daylight saving time.NTP is short for Network Time Protocol. NTP synchronizes computer clock times in a network of computers. Check this box to use a NTP server. This will only connect to a server on the Internet, not a local server.Enter the NTP server or select one from the drop-down menu.To manually input the time, enter the values in these fields for the Year, Month, Day, Hour, Minute, and Second and then click Set Time. You can also click Copy Your Computer’s Time Settings.Time Zone:Daylight Saving:Enable NTP Server:NTP Server Used:Manual:The Time Configuration option allows you to configure, update, and maintain the correct time on the internal system clock. From this section you can set the time zone that you are in and set the Time Server. Daylight Saving can also be configured to automatically adjust the time when needed.
66D-Link DIR-601 User ManualSection 3 - ConfigurationSysLogThe Broadband Router keeps a running log of events and activities occurring on the Router. You may send these logs to a SysLog server on your network.Enable Logging to SysLog Server:SysLog Server IP Address:Check this box to send the router logs to a SysLog Server.The address of the SysLog server that will be used to send the logs. You may also select your computer from the drop-down menu (only if receiving an IP address from the router via DHCP).
67D-Link DIR-601 User ManualSection 3 - ConfigurationE-mail SettingsThe Email feature can be used to send the system log files, router alert messages, and firmware update notification to your e-mail address. Enable Email Notification: From Email Address:To Email Address:SMTP Server Address:Enable Authentication:Account Name:Password:On Log Full:On Schedule:Schedule:When this option is enabled, router activity logs are e-mailed to a designated e-mail address.This e-mail address will appear as the sender when you receive a log file or firmware upgrade notification via e-mail.Enter the e-mail address where you want the e-mail sent. Enter the SMTP server address for sending e-mail. If your SMTP server requires authentication, select this option.Check this box if your SMTP server requires authentication. Enter your account for sending e-mail.Enter the password associated with the account. Re-type the password associated with the account.When this option is selected, logs will be sent via e-mail when the log is full.Selecting this option will send the logs via e-mail according to schedule.This option is enabled when On Schedule is selected. You can select a schedule from the list of defined schedules. To create a schedule, go to Tools > Schedules.
68D-Link DIR-601 User ManualSection 3 - ConfigurationUse this option to save the current router configuration settings to a file on the hard disk of the computer you are using. First, click the Save button. You will then see a file dialog, where you can select a location and file name for the settings. Use this option to load previously saved router configuration settings. First, use the Browse control to find a previously save file of configuration settings. Then, click the Load button to transfer those settings to the router. This option will restore all configuration settings back to the settings that were in effect at the time the router was shipped from the factory. Any settings that have not been saved will be lost, including any rules that you have created. If you want to save the current router configuration settings, use the Save button above. Click to reboot the router.Save Settings to Local Hard Drive:Load Settings from Local Hard Drive:Restore to Factory Default Settings:Reboot Device:System Settings
69D-Link DIR-601 User ManualSection 3 - ConfigurationClick on Check Now to find out if there is an updated firmware; if so, download the new firmware to your hard drive.After you have downloaded the new firmware, click Browse to locate the firmware update on your hard drive. Click Upload to complete the firmware upgrade.Check Now: Firmware Upgrade:Update FirmwareYou can upgrade the firmware of the Router here. Make sure the firmware you want to use is on the local hard drive of the computer. Click on Browse to locate the firmware file to be used for the update. Please check the D-Link support site for firmware updates at http://support.dlink.com. You can download firmware upgrades to your hard drive from the D-Link support site.
70D-Link DIR-601 User ManualSection 3 - ConfigurationCheck to enable DDNS.Choose your DDNS provider from the drop down menu.Enter the Host Name that you registered with your DDNS service provider.Enter the Username for your DDNS account.Enter the Password for your DDNS account.Enter a time (in hours).Displays the current connection status to your DDNS server.Enable DDNS:Server Address:Host Name:Username or Key:Password or Key:Timeout:Status:DDNSThe DDNS feature allows you to host a server (Web, FTP, Game Server, etc…) using a domain name that you have purchased (www.whateveryournameis.com) with your dynamically assigned IP address. Most broadband Internet Service Providers assign dynamic (changing) IP addresses. Using a DDNS service provider, your friends can enter in your domain name to connect to your server no matter what your IP address is.
71D-Link DIR-601 User ManualSection 3 - ConfigurationSystem CheckThe Ping Test is used to send Ping packets to test if a computer is on the Internet. Enter the IP Address that you wish to Ping, and click Ping.The results of your ping attempts will be displayed here.Ping Test/IPv6 Ping Test:Ping Results:
72D-Link DIR-601 User ManualSection 3 - ConfigurationEnter a name for your new schedule.Select a day, a range of days, or All Week to include every day.Check All Day - 24hrs or enter a start and end time for your schedule.Click Save to save your schedule. You must click Save Settings at the top for your schedules to go into effect.The list of schedules will be listed here. Click the Edit icon to make changes or click the Delete icon to remove the schedule.Name:Days:Time:Save:Schedule Rules List:Schedules
73D-Link DIR-601 User ManualSection 3 - ConfigurationThis page displays the current information for the DIR-601. It will display the LAN, WAN (Internet), and Wireless information.Device InformationIf your Internet connection is set up for a Dynamic IP address then a Release button and a Renew button will be displayed. Use Release to disconnect from your ISP and use Renew to connect to your ISP. If your Internet connection is set up for PPPoE, a Connect button and a Disconnect button will be displayed. Use Disconnect to drop the PPPoE connection and use Connect to establish the PPPoE connection.See the following page for more information.
74D-Link DIR-601 User ManualSection 3 - ConfigurationDisplays the router’s time and firmware version.Displays the MAC address and the public IP settings for the router.Displays the MAC address and the private (local) IP settings for the router.Displays the wireless MAC address and your wireless settings such as SSID and Channel.Displays computers and devices that are connected to the router via Ethernet and that are receiving an IP address assigned by the router (DHCP). Displays the Multicast Group IP Address.General:WAN:LAN:Wireless LAN:LAN Computers:IGMP Multicast Memberships:
75D-Link DIR-601 User ManualSection 3 - ConfigurationLogLog Options:Apply Log Settings:Refresh:Clear:Email Now:Save Log:You can select the types of messages that you want to display from the log. Will filter the log results so that only the selected options appear.Updates the log details on the screen so it displays any recent activity.Clears all of the log contents.This option will send a copy of the router log to the e-mail address configured in the Tools > Email Settings screen.This option will save the router to a log file on your computer.The router automatically logs (records) events of possible interest in it’s internal memory. If there isn’t enough internal memory for all events, logs of older events are deleted but logs of the latest events are retained. The Logs option allows you to view the router logs. You can define what types of events you want to view and the level of the events to view. This router also has external Syslog Server support so you can send the log files to a computer on your network that is running a Syslog utility.
76D-Link DIR-601 User ManualSection 3 - ConfigurationStatsThe screen below displays the Traffic Statistics. Here you can view the amount of packets that pass through the DIR-601 on both the Internet and the LAN ports. The traffic counter will reset if the device is rebooted.
77D-Link DIR-601 User ManualSection 3 - ConfigurationInternet SessionsThe Internet Sessions page displays full details of active Internet sessions through your router. An Internet session is a conversation between a program or application on a LAN-side computer and a program or application on a WAN-side computer. Local:NAT:Internet:Protocol:State:Dir:The IP address and, where appropriate, port number of the local application. The port number of the LAN-side application as viewed by the WAN-side application. The IP address and, where appropriate, port number of the application on the Internet. The communications protocol used for the conversation. State for sessions that use the TCP protocol: NO: None -- This entry is used as a placeholder for a future connection that may occur. SS: SYN Sent -- One of the systems is attempting to start a connection. EST: Established -- the connection is passing data. FW: FIN Wait -- The client system has requested that the connection be stopped. CW: Close Wait -- The server system has requested that the connection be stopped. TW: Time Wait -- Waiting for a short time while a connection that was in FIN Wait is fully closed. LA: Last ACK -- Waiting for a short time while a connection that was in Close Wait is fully closed. CL: Closed -- The connection is no longer active but the session is being tracked in case there are any retransmitted packets still pending.The direction of initiation of the conversation: Out - Initiated from LAN to WAN. In - Initiated from WAN to LAN.
78D-Link DIR-601 User ManualSection 3 - ConfigurationPriority:Time Out:The preference given to outbound packets of this conversation by the QoS Engine logic. Smaller numbers represent higher priority. The number of seconds of idle time until the router considers the session terminated. The initial value of Time Out depends on the type and state of the connection. 300 seconds - UDP connections.240 seconds - Reset or closed TCP connections. The connection does not close instantly so that lingering packets can pass or the connection can be re-established. 7800 seconds - Established or closing TCP connections.
79D-Link DIR-601 User ManualSection 3 - ConfigurationThis page displays the routing details configured for your router.Routing Table
80D-Link DIR-601 User ManualSection 3 - ConfigurationThe wireless client table displays a list of current connected wireless clients. This table also displays the connection time and MAC address of the connected wireless clients.Wireless
81D-Link DIR-601 User ManualSection 3 - ConfigurationAll of your IPv6 Internet and network connection details are displayed on this page.IPv6
82D-Link DIR-601 User ManualSection 3 - ConfigurationSupport
83D-Link DIR-601 User ManualSection 4 - SecurityWireless SecurityThis section will show you the different levels of security you can use to protect your data from intruders. The DIR-601 offers the following types of security:• WPA2 (Wi-Fi Protected Access 2) • WPA2-PSK(Pre-Shared Key)• WPA (Wi-Fi Protected Access) • WPA-PSK (Pre-Shared Key)What is WPA?WPA, or Wi-Fi Protected Access, is a Wi-Fi standard that was designed to improve the security features of WEP (Wired Equivalent Privacy). The 2 major improvements over WEP: • Improved data encryption through the Temporal Key Integrity Protocol (TKIP). TKIP scrambles the keys using a hashing algorithm and, by adding an integrity-checking feature, ensures that the keys haven’t been tampered with. WPA2 is based on 802.11i and uses Advanced Encryption Standard (AES) instead of TKIP.• User authentication, which is generally missing in WEP, through the extensible authentication protocol (EAP). WEP regulates access to a wireless network based on a computer’s hardware-specific MAC address, which is relatively simple to be sniffed out and stolen. EAP is built on a more secure public-key encryption system to ensure that only authorized network users can access the network.WPA-PSK/WPA2-PSK uses a passphrase or key to authenticate your wireless connection. The key is an alpha-numeric password between 8 and 63 characters long. The password can include symbols (!?*&_) and spaces. This key must be the exact same key entered on your wireless router or access point.WPA/WPA2 incorporates user authentication through the Extensible Authentication Protocol (EAP). EAP is built on a more secure public key encryption system to ensure that only authorized network users can access the network.
84D-Link DIR-601 User ManualSection 4 - SecurityWireless Connection Setup WizardTo run the security wizard, browse to the Setup page and then click the Wireless Connection Setup Wizard button. Click Next to continue.
85D-Link DIR-601 User ManualSection 4 - SecurityEnter the SSID (Service Set Identifier). The SSID is the name of your wireless network. Create a name using up to 32 characters. The SSID is case-sensitive.Select Automatically assign a network key to have the router create a security key for you or select Manually assign a network key if you would like to create your own security key or passphrase.If you want to use WPA, check the Use WPA encryption instead of WEP box.If you select Manually assign a network key, enter your encryption key in the box and click Next to continue. You will need to enter this key on your wireless clients to connect to the router.If you selected Automatically, the following screen will show you your security key to enter on your wireless clients. Click Save to finish the Security Wizard.
86D-Link DIR-601 User ManualSection 4 - SecurityFrom the Setup > Wireless Settings screen, click Add Wireless Device with WPS.Add Wireless Device with WPS WizardPIN: Select this option to use PIN method. In order to use this method you must know the wireless client’s 8 digit PIN and click Connect.PBC: Select this option to use PBC (Push Button) method to add a wireless client. Click Connect.Select Auto to add a wireless client using WPS (Wi-Fi Protected Setup). Once you select Auto and click Connect, you will have a 120 second time limit to apply the settings to your wireless client(s) and successfully establish a connection. If you select Manual, a settings summary screen will appear. Write down the security key and enter this on your wireless clients.
87D-Link DIR-601 User ManualSection 4 - SecurityConfigure WPA-Personal (PSK)It is recommended to enable encryption on your wireless router before your wireless network adapters. Please establish wireless connectivity before enabling encryption. Your wireless signal may degrade when enabling encryption due to the added overhead.1. Log into the web-based configuration by opening a web browser and entering the IP address of the router (192.168.0.1). Click on Setup and then click Wireless Settings on the left side.2. Next to Security Mode, select WPA-Personal.3. Next to WPA Mode, select Auto, WPA2 Only, or WPA Only. Use Auto if you have wireless clients using both WPA and WPA2.4. Next to Cypher Type, select TKIP and AES, TKIP, or AES. If you have wireless clients that use both types, use TKIP and AES.5. Next to Group Key Update Interval, enter the amount of time before the group key used for broadcast and multicast data is changed (3600 is default).6. Next to Pre-Shared Key, enter a key (passphrase). The key is entered as a pass-phrase in ASCII format at both ends of the wireless connection. The pass-phrase must be between 8-63 characters. 7. Click Save Settings to save your settings. If you are configuring the router with a wireless adapter, you will lose connectivity until you enable WPA-PSK on your adapter and enter the same passphrase as you did on the router.
88D-Link DIR-601 User ManualSection 4 - SecurityIt is recommended to enable encryption on your wireless router before your wireless network adapters. Please establish wireless connectivity before enabling encryption. Your wireless signal may degrade when enabling encryption due to the added overhead.1. Log into the web-based configuration by opening a web browser and entering the IP address of the router (192.168.0.1). Click on Setup and then click Wireless Settings on the left side.2. Next to Security Mode, select WPA-Enterprise.3. Next to WPA Mode, select Auto, WPA2 Only, or WPA Only. Use Auto if you have wireless clients using both WPA and WPA2.4. Next to Cypher Type, select TKIP and AES, TKIP, or AES. If you have wireless clients that use both types, use TKIP and AES.5. Next to Group Key Update Interval, enter the amount of time before the group key used for broadcast and multicast data is changed (3600 is default).6. Next to Authentication Timeout, enter the amount of time before a client is required to re-authenticate (60 minutes is default). 7. Next to RADIUS Server IP Address enter the IP Address of your RADIUS server.8. Next to RADIUS Server Port, enter the port you are using with your RADIUS server. 1812 is the default port.9. Next to RADIUS Server Shared Secret, enter the security key.Configure WPA-Enterprise (RADIUS)
89D-Link DIR-601 User ManualSection 4 - Security10. If the MAC Address Authentication box is selected then the user will need to connect from the same computer whenever logging into the wireless network.11. Click Advanced to enter settings for a secondary RADIUS Server.12. Click Apply Settings to save your settings.
90D-Link DIR-601 User ManualSection 5 - Connecting to a Wireless NetworkConnect to a Wireless NetworkUsing Windows Vista®Windows Vista® users may use the built-in wireless utility. If you are using another company’s utility or Windows® 2000, please refer to the user manual of your wireless adapter for help with connecting to a wireless network. Most utilities will have a “site survey” option similar to the Windows Vista® utility as seen below.Right-click on the wireless computer icon in your system tray (lower-right corner next to the time). Select Connect to a network.If you receive the Wireless Networks Detected bubble, click on the center of the bubble to access the utility. orThe utility will display any available wireless networks in your area. Click on a network (displayed using the SSID) and click the Connect button.If you get a good signal but cannot access the Internet, check you TCP/IP settings for your wireless adapter. Refer to the Networking Basics section in this manual for more information.
91D-Link DIR-601 User ManualSection 5 - Connecting to a Wireless NetworkConfigure WPA/WPA2It is recommended to enable wireless security (WPA/WPA2) on your wireless router or access point before configuring your wireless adapter. If you are joining an existing network, you will need to know the security key or passphrase being used.2. Highlight the wireless network (SSID) you would like to connect to and click Connect.1. Open the Windows Vista® Wireless Utility by right-clicking on the wireless computer icon in your system tray (lower right corner of screen). Select Connect to a network.
92D-Link DIR-601 User ManualSection 5 - Connecting to a Wireless Network3. Enter the same security key or passphrase that is on your router and click Connect.It may take 20-30 seconds to connect to the wireless network. If the connection fails, please verify that the security settings are correct. The key or passphrase must be exactly the same as on the wireless router.
93D-Link DIR-601 User ManualSection 5 - Connecting to a Wireless NetworkConnect Using WCN 2.0The router supports Wi-Fi protection, referred to as WCN 2.0 in Windows Vista®. The following instructions for setting this up depends on whether you are using Windows Vista® to configure the router or third party software. When you first set up the router, Wi-Fi protection is disabled and unconfigured. To enjoy the benefits of Wi-Fi protection, the router must be both enabled and configured. There are three basic methods to accomplish this: use Windows Vista’s built-in support for WCN 2.0, use software provided by a third party, or manually configure. If you are running Windows Vista®, log into the router and click the Enable checkbox in the Basic > Wireless section. Use the Current PIN that is displayed on the Advanced > Wi-Fi Protected Setup section or choose to click the Generate New PIN button or Reset PIN to Default button. If you are using third party software to set up Wi-Fi Protection, carefully follow the directions. When you are finished, proceed to the next section to set up the newly-configured router.
94D-Link DIR-601 User ManualSection 5 - Connecting to a Wireless NetworkUsing Windows® XPWindows® XP users may use the built-in wireless utility (Zero Configuration Utility). The following instructions are for Service Pack 2 users. If you are using another company’s utility or Windows® 2000, please refer to the user manual of your wireless adapter for help with connecting to a wireless network. Most utilities will have a “site survey” option similar to the Windows® XP utility as seen below.If you receive the Wireless Networks Detected bubble, click on the center of the bubble to access the utility. orRight-click on the wireless computer icon in your system tray (lower-right corner next to the time). Select View Available Wireless Networks.The utility will display any available wireless networks in your area. Click on a network (displayed using the SSID) and click the Connect button.If you get a good signal but cannot access the Internet, check you TCP/IP settings for your wireless adapter. Refer to the Networking Basics section in this manual for more information.
95D-Link DIR-601 User ManualSection 5 - Connecting to a Wireless NetworkConfigure WPA-PSKIt is recommended to enable WEP on your wireless router or access point before configuring your wireless adapter. If you are joining an existing network, you will need to know the WEP key being used.2. Highlight the wireless network (SSID) you would like to connect to and click Connect.1. Open the Windows® XP Wireless Utility by right-clicking on the wireless computer icon in your system tray (lower-right corner of screen). Select View Available Wireless Networks.
96D-Link DIR-601 User ManualSection 5 - Connecting to a Wireless Network3. The Wireless Network Connection box will appear. Enter the WPA-PSK passphrase and click Connect.It may take 20-30 seconds to connect to the wireless network. If the connection fails, please verify that the WPA-PSK settings are correct. The WPA-PSK passphrase must be exactly the same as on the wireless router.
97D-Link DIR-601 User ManualSection 6 - TroubleshootingTroubleshootingThis chapter provides solutions to problems that can occur during the installation and operation of the DIR-601. Read the following descriptions if you are having problems. (The examples below are illustrated in Windows® XP. If you have a different operating system, the screen shots on your computer will look similar to the following examples.)1. Why can’t I access the web-based configuration utility?When entering the IP address of the D-Link router (192.168.0.1 for example), you are not connecting to a website on the Internet or have to be connected to the Internet. The device has the utility built-in to a ROM chip in the device itself. Your computer must be on the same IP subnet to connect to the web-based utility. • Make sure you have an updated Java-enabled web browser. We recommend the following: • Microsoft Internet Explorer® 6.0 and higher• Mozilla Firefox 3.0 and higher• Google™ Chrome 2.0 and higher• Apple Safari 3.0 and higher• Verify physical connectivity by checking for solid link lights on the device. If you do not get a solid link light, try using a different cable or connect to a different port on the device if possible. If the computer is turned off, the link light may not be on.• Disable any Internet security software running on the computer. Software firewalls such as Zone Alarm, Black Ice, Sygate, Norton Personal Firewall, and Windows® XP firewall may block access to the configuration pages. Check the help files included with your firewall software for more information on disabling or configuring it.
98D-Link DIR-601 User ManualSection 6 - Troubleshooting• Configure your Internet settings:• Go to Start > Settings > Control Panel. Double-click the Internet Options Icon. From the Security tab, click the button to restore the settings to their defaults.• Click the Connection tab and set the dial-up option to Never Dial a Connection. Click the LAN Settings button. Make sure nothing is checked. Click OK. • Go to the Advanced tab and click the button to restore these settings to their defaults. Click OK three times.• Close your web browser (if open) and open it.• Access the web management. Open your web browser and enter the IP address of your D-Link router in the address bar. This should open the login page for your the web management. • If you still cannot access the configuration, unplug the power to the router for 10 seconds and plug back in. Wait about 30 seconds and try accessing the configuration. If you have multiple computers, try connecting using a different computer.2. What can I do if I forgot my password?If you forgot your password, you must reset your router. Unfortunately this process will change all your settings back to the factory defaults.To reset the router, locate the reset button (hole) on the rear panel of the unit. With the router powered on, use a paperclip to hold the button down for 10 seconds. Release the button and the router will go through its reboot process. Wait about 30 seconds to access the router. The default IP address is 192.168.0.1. When logging in, the username is admin and leave the password box empty.
99D-Link DIR-601 User ManualSection 6 - Troubleshooting3. Why can’t I connect to certain sites or send and receive e-mails when connecting through my router? If you are having a problem sending or receiving e-mail, or connecting to secure sites such as eBay, banking sites, and Hotmail, we suggest lowering the MTU in increments of ten (Ex. 1492, 1482, 1472, etc). Note: AOL DSL+ users must use MTU of 1400. To find the proper MTU Size, you’ll have to do a special ping of the destination you’re trying to go to. A destination could be another computer, or a URL. • Click on Start and then click Run. • Windows® 95, 98, and Me users type in command (Windows® NT, 2000, and XP users type in cmd) and press Enter (or click OK). • Once the window opens, you’ll need to do a special ping. Use the following syntax: ping [url] [-f] [-l] [MTU value] Example: ping yahoo.com -f -l 1472
100D-Link DIR-601 User ManualSection 6 - TroubleshootingYou should start at 1472 and work your way down by 10 each time. Once you get a reply, go up by 2 until you get a fragmented packet. Take that value and add 28 to the value to account for the various TCP/IP headers. For example, lets say that 1452 was the proper value, the actual MTU size would be 1480, which is the optimum for the network we’re working with (1452+28=1480). Once you find your MTU, you can now configure your router with the proper MTU size. To change the MTU rate on your router follow the steps below: • Open your browser, enter the IP address of your router (192.168.0.1) and click OK. • Enter your username (admin) and password (blank by default). Click OK to enter the web configuration page for the device. • Click on Setup and then click Manual Configure. • To change the MTU enter the number in the MTU field and click Save Settings to save your settings. • Test your e-mail. If changing the MTU does not resolve the problem, continue changing the MTU in increments of ten.
101D-Link DIR-601 User ManualAppendix A - Wireless BasicsD-Link wireless products are based on industry standards to provide easy-to-use and compatible high-speed wireless connectivity within your home, business or public access wireless networks. Strictly adhering to the IEEE standard, the D-Link wireless family of products will allow you to securely access the data you want, when and where you want it. You will be able to enjoy the freedom that wireless networking delivers.A wireless local area network (WLAN) is a cellular computer network that transmits and receives data with radio signals instead of wires. Wireless LANs are used increasingly in both home and office environments, and public areas such as airports, coffee shops and universities. Innovative ways to utilize WLAN technology are helping people to work and communicate more efficiently. Increased mobility and the absence of cabling and other fixed infrastructure have proven to be beneficial for many users. Wireless users can use the same applications they use on a wired network. Wireless adapter cards used on laptop and desktop systems support the same protocols as Ethernet adapter cards. Under many circumstances, it may be desirable for mobile network devices to link to a conventional Ethernet LAN in order to use servers, printers or an Internet connection supplied through the wired LAN. A Wireless Router is a device used to provide this link.Wireless Basics
102D-Link DIR-601 User ManualAppendix A - Wireless BasicsWhat is Wireless?Wireless or Wi-Fi technology is another way of connecting your computer to the network without using wires. Wi-Fi uses radio frequency to connect wirelessly, so you have the freedom to connect computers anywhere in your home or office network.Why D-Link Wireless? D-Link is the worldwide leader and award winning designer, developer, and manufacturer of networking products. D-Link delivers the performance you need at a price you can afford. D-Link has all the products you need to build your network.How does wireless work? Wireless works similar to how cordless phone work, through radio signals to transmit data from one point A to point B. But wireless technology has restrictions as to how you can access the network. You must be within the wireless network range area to be able to connect your computer. There are two different types of wireless networks Wireless Local Area Network (WLAN), and Wireless Personal Area Network (WPAN).Wireless Local Area Network (WLAN)In a wireless local area network, a device called an Access Point (AP) connects computers to the network. The access point has a small antenna attached to it, which allows it to transmit data back and forth over radio signals. With an indoor access point as seen in the picture, the signal can travel up to 300 feet. With an outdoor access point the signal can reach out up to 30 miles to serve places like manufacturing plants, industrial locations, college and high school campuses, airports, golf courses, and many other outdoor venues.
103D-Link DIR-601 User ManualAppendix A - Wireless BasicsWireless Personal Area Network (WPAN)Bluetooth is the industry standard wireless technology used for WPAN. Bluetooth devices in WPAN operate in a range up to 30 feet away.Compared to WLAN the speed and wireless operation range are both less than WLAN, but in return it doesn’t use nearly as much power which makes it ideal for personal devices, such as mobile phones, PDAs, headphones, laptops, speakers, and other devices that operate on batteries.Who uses wireless? Wireless technology as become so popular in recent years that almost everyone is using it, whether it’s for home, office, business, D-Link has a wireless solution for it.Home• Gives everyone at home broadband access• Surf the web, check e-mail, instant message, and etc• Gets rid of the cables around the house• Simple and easy to use Small Office and Home Office• Stay on top of everything at home as you would at office• Remotely access your office network from home• Share Internet connection and printer with multiple computers• No need to dedicate office space
104D-Link DIR-601 User ManualAppendix A - Wireless BasicsWhere is wireless used? Wireless technology is expanding everywhere not just at home or office. People like the freedom of mobility and it’s becoming so popular that more and more public facilities now provide wireless access to attract people. The wireless connection in public places is usually called “hotspots”.Using a D-Link Cardbus Adapter with your laptop, you can access the hotspot to connect to Internet from remote locations like: Airports, Hotels, Coffee Shops, Libraries, Restaurants, and Convention Centers.Wireless network is easy to setup, but if you’re installing it for the first time it could be quite a task not knowing where to start. That’s why we’ve put together a few setup steps and tips to help you through the process of setting up a wireless network.TipsHere are a few things to keep in mind, when you install a wireless network.Centralize your router or Access Point Make sure you place the router/access point in a centralized location within your network for the best performance. Try to place the router/access point as high as possible in the room, so the signal gets dispersed throughout your home. If you have a two-story home, you may need a repeater to boost the signal to extend the range.Eliminate Interference Place home appliances such as cordless telephones, microwaves, and televisions as far away as possible from the router/access point. This would significantly reduce any interference that the appliances might cause since they operate on same frequency.
105D-Link DIR-601 User ManualAppendix A - Wireless BasicsSecurity Don’t let you next-door neighbors or intruders connect to your wireless network. Secure your wireless network by turning on the WPA or WEP security feature on the router. Refer to product manual for detail information on how to set it up.There are basically two modes of networking: • Infrastructure – All wireless clients will connect to an access point or wireless router.• Ad-Hoc – Directly connecting to another computer, for peer-to-peer communication, using wireless network adapters on each computer, such as two or more DIR-601 wireless network Cardbus adapters.An Infrastructure network contains an Access Point or wireless router. All the wireless devices, or clients, will connect to the wireless router or access point. An Ad-Hoc network contains only clients, such as laptops with wireless cardbus adapters. All the adapters must be in Ad-Hoc mode to communicate.Wireless Modes
106D-Link DIR-601 User ManualAppendix B - Networking BasicsNetworking BasicsCheck your IP addressAfter you install your adapter, by default, the TCP/IP settings should be set to obtain an IP address from a DHCP server (i.e. wireless router) automatically. To verify your IP address, please follow the steps below.Click on Start > Run. In the run box type cmd and click OK. (Windows Vista® users type cmd in the Start Search box.)At the prompt, type ipconfig and press Enter.This will display the IP address, subnet mask, and the default gateway of your adapter.If the address is 0.0.0.0, check your adapter installation, security settings, and the settings on your router. Some firewall software programs may block a DHCP request on newly installed adapters.
107D-Link DIR-601 User ManualAppendix B - Networking BasicsStatically Assign an IP addressIf you are not using a DHCP capable gateway/router, or you need to assign a static IP address, please follow the steps below:Step 1Windows Vista® - Click on Start > Control Panel > Network and Internet > Network and Sharing Center > Manage Network Connections.Windows® XP - Click on Start > Control Panel > Network Connections.Windows® 2000 - From the desktop, right-click My Network Places > Properties.Step 2Right-click on the Local Area Connection which represents your network adapter and select Properties.Step 3Highlight Internet Protocol (TCP/IP) and click Properties.Step 4Click Use the following IP address and enter an IP address that is on the same subnet as your network or the LAN IP address on your router. Example: If the router´s LAN IP address is 192.168.0.1, make your IP address 192.168.0.X where X is a number between 2 and 99. Make sure that the number you choose is not in use on the network. Set Default Gateway the same as the LAN IP address of your router (192.168.0.1). Set Primary DNS the same as the LAN IP address of your router (192.168.0.1). The Secondary DNS is not needed or you may enter a DNS server from your ISP.Step 5Click OK twice to save your settings.
108D-Link DIR-601 User ManualAppendix C - Technical SpecificationsTechnical SpecificationsStandards • IEEE 802.11n (draft 2.0) • IEEE 802.11g • IEEE 802.3 • IEEE 802.3uSecurity • WPA-Personal • WPA2-Personal • WPA-Enterprise • WPA2-EnterpriseData Rates* MSC (0-15) • 6.5Mbps (13.5) • 7.2Mbps (15) • 13Mbps (27) • 14.4Mbps (30) • 19.5Mbps (40.5) • 21.7Mbps (45) • 26Mbps (54) • 28.9Mbps (60) • 39Mbps (81) • 43.3Mbps (90) • 52Mbps (108) • 57.8Mbps (120) • 58.5Mbps (121.5) • 65Mbps (135) • 65Mbps (135) • 72.2Mbps (150) Frequency Range • 2.4GHz to 2.4835GHzTransmitter Output Power • 24dBmLEDs • Power • Internet • WLAN • LAN (10/100) Operating Temperature • 32°F to 104°F ( 0°C to 40°C)Humidity • 95% maximum (non-condensing)Safety & Emissions • FCC • IC Dimensions • L = 7.6 inches • W = 4.6 inches • H = 1.2inchesWarranty • 1 Year Limited* Maximum wireless signal rate derived from IEEE Standard 802.11g and Draft 802.11n specifications. Actual data throughput will vary. Network conditions and environmental factors, including volume of network traffic, building materials and construction, and network overhead, lower actual data throughput rate. Environmental factors will adversely affect wireless signal range.
109D-Link DIR-601 User ManualAppendix D - Contacting Technical SupportContacting Technical SupportU.S. and Canadian customers can contact D-Link technical support through our web site or by phone.Before you contact technical support, please have the following ready: • Model number of the product (e.g. DIR-601) • Hardware Revision (located on the label on the bottom of the router (e.g. rev A1)) • Serial Number (s/n number located on the label on the bottom of the router). You can find software updates and user documentation on the D-Link website as well as frequently asked questions and answers to technical issues.For customers within the United States: Phone Support:(877) 453-5465Internet Support:http://support.dlink.com For customers within Canada: Phone Support:(800) 361-5265 Internet Support:http://support.dlink.com
110D-Link DIR-601 User ManualAppendix E - WarrantyWarrantySubject to the terms and conditions set forth herein, D-Link Systems, Inc. (“D-Link”) provides this Limited Warranty: • Only to the person or entity that originally purchased the product from D-Link or its authorized reseller or distributor, and • Only for products purchased and delivered within the fifty states of the United States, the District of Columbia, U.S. Possessions or Protectorates, U.S. Military Installations, or addresses with an APO or FPO.Limited Warranty:D-Link warrants that the hardware portion of the D-Link product described below (“Hardware”) will be free from material defects in workmanship and materials under normal use from the date of original retail purchase of the product, for the period set forth below (“Warranty Period”), except as otherwise stated herein. • Hardware (excluding power supplies and fans): One (1) year limited • Power supplies and fans: One (1) year limited • Spare parts and spare kits: Ninety (90) daysThe customer’s sole and exclusive remedy and the entire liability of D-Link and its suppliers under this Limited Warranty will be, at D-Link’s option, to repair or replace the defective Hardware during the Warranty Period at no charge to the original owner or to refund the actual purchase price paid. Any repair or replacement will be rendered by D-Link at an Authorized D-Link Service Office. The replacement hardware need not be new or have an identical make, model or part. D-Link may, at its option, replace the defective Hardware or any part thereof with any reconditioned product that D-Link reasonably determines is substantially equivalent (or superior) in all material respects to the defective Hardware. Repaired or replacement hardware will be warranted for the remainder of the original Warranty Period or ninety (90) days, whichever is longer, and is subject to the same limitations and exclusions. If a material defect is incapable of correction, or if D-Link determines that it is not practical to repair or replace the defective Hardware, the actual price paid by the original purchaser for the defective Hardware will be refunded by D-Link upon return to D-Link of the defective Hardware. All Hardware or part thereof that is replaced by D-Link, or for which the purchase price is refunded, shall become the property of D-Link upon replacement or refund.
111D-Link DIR-601 User ManualAppendix E - WarrantyLimited Software Warranty:D-Link warrants that the software portion of the product (“Software”) will substantially conform to D-Link’s then current functional specifications for the Software, as set forth in the applicable documentation, from the date of original retail purchase of the Software for a period of ninety (90) days (“Software Warranty Period”), provided that the Software is properly installed on approved hardware and operated as contemplated in its documentation. D-Link further warrants that, during the Software Warranty Period, the magnetic media on which D-Link delivers the Software will be free of physical defects. The customer’s sole and exclusive remedy and the entire liability of D-Link and its suppliers under this Limited Warranty will be, at D-Link’s option, to replace the non-conforming Software (or defective media) with software that substantially conforms to D-Link’s functional specifications for the Software or to refund the portion of the actual purchase price paid that is attributable to the Software. Except as otherwise agreed by D-Link in writing, the replacement Software is provided only to the original licensee, and is subject to the terms and conditions of the license granted by D-Link for the Software. Replacement Software will be warranted for the remainder of the original Warranty Period and is subject to the same limitations and exclusions. If a material non-conformance is incapable of correction, or if D-Link determines in its sole discretion that it is not practical to replace the non-conforming Software, the price paid by the original licensee for the non-conforming Software will be refunded by D-Link; provided that the non-conforming Software (and all copies thereof) is first returned to D-Link. The license granted respecting any Software for which a refund is given automatically terminates.Non-Applicability of Warranty:The Limited Warranty provided hereunder for Hardware and Software portions of D-Link’s products will not be applied to and does not cover any refurbished product and any product purchased through the inventory clearance or liquidation sale or other sales in which D-Link, the sellers, or the liquidators expressly disclaim their warranty obligation pertaining to the product and in that case, the product is being sold “As-Is” without any warranty whatsoever including, without limitation, the Limited Warranty as described herein, notwithstanding anything stated herein to the contrary.Submitting A Claim: The customer shall return the product to the original purchase point based on its return policy. In case the return policy period has expired and the product is within warranty, the customer shall submit a claim to D-Link as outlined below:• The customer must submit with the product as part of the claim a written description of the Hardware defect or Software nonconformance in sufficient detail to allow D-Link to confirm the same, along with proof of purchase of the product (such as a copy of the dated purchase invoice for the product) if the product is not registered.• The customer must obtain a Case ID Number from D-Link Technical Support at 1-877-453-5465, who will attempt to assist the customer in resolving any suspected defects with the product. If the product is considered defective, the customer must obtain a Return Material Authorization (“RMA”) number by completing the RMA form and entering the assigned Case ID Number at https://rma.dlink.com/.
112D-Link DIR-601 User ManualAppendix E - Warranty• After an RMA number is issued, the defective product must be packaged securely in the original or other suitable shipping package to ensure that it will not be damaged in transit, and the RMA number must be prominently marked on the outside of the package. Do not include any manuals or accessories in the shipping package. D-Link will only replace the defective portion of the product and will not ship back any accessories.• The customer is responsible for all in-bound shipping charges to D-Link. No Cash on Delivery (“COD”) is allowed. Products sent COD will either be rejected by D-Link or become the property of D-Link. Products shall be fully insured by the customer and shipped to D-Link Systems, Inc., 17595 Mt. Herrmann, Fountain Valley, CA 92708. D-Link will not be held responsible for any packages that are lost in transit to D-Link. The repaired or replaced packages will be shipped to the customer via UPS Ground or any common carrier selected by D-Link. Return shipping charges shall be prepaid by D-Link if you use an address in the United States, otherwise we will ship the product to you freight collect. Expedited shipping is available upon request and provided shipping charges are prepaid by the customer. D-Link may reject or return any product that is not packaged and shipped in strict compliance with the foregoing requirements, or for which an RMA number is not visible from the outside of the package. The product owner agrees to pay D-Link’s reasonable handling and return shipping charges for any product that is not packaged and shipped in accordance with the foregoing requirements, or that is determined by D-Link not to be defective or non-conforming.What Is Not Covered:The Limited Warranty provided herein by D-Link does not cover:Products that, in D-Link’s judgment, have been subjected to abuse, accident, alteration, modification, tampering, negligence, misuse, faulty installation, lack of reasonable care, repair or service in any way that is not contemplated in the documentation for the product, or if the model or serial number has been altered, tampered with, defaced or removed; Initial installation, installation and removal of the product for repair, and shipping costs; Operational adjustments covered in the operating manual for the product, and normal maintenance; Damage that occurs in shipment, due to act of God, failures due to power surge, and cosmetic damage; Any hardware, software, firmware or other products or services provided by anyone other than D-Link; and Products that have been purchased from inventory clearance or liquidation sales or other sales in which D-Link, the sellers, or the liquidators expressly disclaim their warranty obligation pertaining to the product.While necessary maintenance or repairs on your Product can be performed by any company, we recommend that you use only an Authorized D-Link Service Office. Improper or incorrectly performed maintenance or repair voids this Limited Warranty.Disclaimer of Other Warranties:EXCEPT FOR THE LIMITED WARRANTY SPECIFIED HEREIN, THE PRODUCT IS PROVIDED “AS-IS” WITHOUT ANY WARRANTY OF ANY KIND WHATSOEVER INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT.
113D-Link DIR-601 User ManualAppendix E - WarrantyIF ANY IMPLIED WARRANTY CANNOT BE DISCLAIMED IN ANY TERRITORY WHERE A PRODUCT IS SOLD, THE DURATION OF SUCH IMPLIED WARRANTY SHALL BE LIMITED TO THE DURATION OF THE APPLICABLE WARRANTY PERIOD SET FORTH ABOVE. EXCEPT AS EXPRESSLY COVERED UNDER THE LIMITED WARRANTY PROVIDED HEREIN, THE ENTIRE RISK AS TO THE QUALITY, SELECTION AND PERFORMANCE OF THE PRODUCT IS WITH THE PURCHASER OF THE PRODUCT.Limitation of Liability:TO THE MAXIMUM EXTENT PERMITTED BY LAW, D-LINK IS NOT LIABLE UNDER ANY CONTRACT, NEGLIGENCE, STRICT LIABILITY OR OTHER LEGAL OR EQUITABLE THEORY FOR ANY LOSS OF USE OF THE PRODUCT, INCONVENIENCE OR DAMAGES OF ANY CHARACTER, WHETHER DIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL (INCLUDING, BUT NOT LIMITED TO, DAMAGES FOR LOSS OF GOODWILL, LOSS OF REVENUE OR PROFIT, WORK STOPPAGE, COMPUTER FAILURE OR MALFUNCTION, FAILURE OF OTHER EQUIPMENT OR COMPUTER PROGRAMS TO WHICH D-LINK’S PRODUCT IS CONNECTED WITH, LOSS OF INFORMATION OR DATA CONTAINED IN, STORED ON, OR INTEGRATED WITH ANY PRODUCT RETURNED TO D-LINK FOR WARRANTY SERVICE) RESULTING FROM THE USE OF THE PRODUCT, RELATING TO WARRANTY SERVICE, OR ARISING OUT OF ANY BREACH OF THIS LIMITED WARRANTY, EVEN IF D-LINK HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. THE SOLE REMEDY FOR A BREACH OF THE FOREGOING LIMITED WARRANTY IS REPAIR, REPLACEMENT OR REFUND OF THE DEFECTIVE OR NONCONFORMING PRODUCT. THE MAXIMUM LIABILITY OF D-LINK UNDER THIS WARRANTY IS LIMITED TO THE PURCHASE PRICE OF THE PRODUCT COVERED BY THE WARRANTY. THE FOREGOING EXPRESS WRITTEN WARRANTIES AND REMEDIES ARE EXCLUSIVE AND ARE IN LIEU OF ANY OTHER WARRANTIES OR REMEDIES, EXPRESS, IMPLIED OR STATUTORY.Governing Law:This Limited Warranty shall be governed by the laws of the State of California. Some states do not allow exclusion or limitation of incidental or consequential damages, or limitations on how long an implied warranty lasts, so the foregoing limitations and exclusions may not apply. This Limited Warranty provides specific legal rights and you may also have other rights which vary from state to state.Trademarks:D-Link is a registered trademark of D-Link Corporation/D-Link Systems, Inc. Other trademarks or registered trademarks are the property of their respective owners.Copyright Statement:No part of this publication or documentation accompanying this product may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from D-Link Corporation/D-Link Systems, Inc., as stipulated by the United States Copyright Act of 1976 and any amendments thereto. Contents are subject to change without prior notice.Copyright ©2009 by D-Link Corporation/D-Link Systems, Inc. All rights reserved.
114D-Link DIR-601 User ManualAppendix E - WarrantyCE Mark Warning:This is a Class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.FCC Statement:This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help.For detailed warranty information applicable to products purchased outside the United States, please contact the corresponding local D-Link office.FCC Caution:Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.IMPORTANT NOTE:FCC Radiation Exposure Statement:This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.We declare that the product is limited in CH1~CH11 by specified firmware controlled in the USA.
115D-Link DIR-601 User ManualAppendix E - WarrantyIC statementOperation is subject to the following two conditions:1) This device may not cause interference and2) This device must accept any interference, including interference that may cause undesired operation of the device.This device has been designed to operate with an antenna having a maximum gain of 2dBi. Antenna having a higher gain is strictly prohibited per regulations of Industry Canada. The required antenna impedance is 50 ohms.IMPORTANT NOTE:IC Radiation Exposure Statement:This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.Règlement d’Industry Canada Les conditions de fonctionnement sont sujettes à deux conditions:1) Ce périphérique ne doit pas causer d’interférence et.2) Ce périphérique doit accepter toute interférence, y compris les interférences pouvant perturber le bon fonctionnement de ce périphérique.The Class [B] digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulation. Cet appareil numerique de la class [B] respecte toutes les exigences du Reglement sur le materiel brouilleur du Canada.
116D-Link DIR-601 User ManualAppendix F - RegistrationVersion 1.0October 14, 2009Product registration is entirely voluntary and failure to complete or return this form will not diminish your warranty rights.Registration

Navigation menu