D Link AP1350A1 Wireless N Pocket Router/Access Point User Manual Manual 2

D Link Corporation Wireless N Pocket Router/Access Point Manual 2

UserManual.wiki >

AP1350A1 User Manual >

Contents

Manual 2

30D-Link DAP-1350 User ManualSection 3 - ConﬁgurationMAC Address FilterSelect Enable or Disable from the drop-down menu. Enter the MAC address you would like to ﬁlter.To ﬁnd the MAC address on a computer, please refer to the Networking Basics section in this manual. Click Save Settings to activate and save.Note: Make sure you enter the computer you are currently using to conﬁgure the access point ﬁrst or you will not be able to access the conﬁguration utility once you click Save Settings.Displays the list of clients in the ﬁlter list.MAC Address Filter:MAC Address:MAC Filter List:Use MAC (Media Access Control) Filters to authorize wireless clients by their MAC addresses to access your network. When enabled, any client not on the MAC ﬁlter list will not be able to access your network.

31D-Link DAP-1350 User ManualSection 3 - ConﬁgurationAdvanced WirelessTransmit Power:Beacon Period:DTIM Interval:RTS Threshold:Fragmentation Threshold:WMM Enable:Short GI:Sets the transmit power of the antennas.Note: Transmit power is regulated by international standard. Users are forbidden to change its maximum limit.Beacons are packets sent by an access point to synchronize a wireless network. Specify a value. 100 is the default setting and is recommended. (Delivery Trafﬁc Indication Message) 1 is the default setting. A DTIM is a countdown informing clients of the next window for listening to broadcast and multicast messages.This value should remain at its default setting of 2346. If inconsistent data ﬂow is a problem, only a minor modiﬁcation should be made.The fragmentation threshold, which is speciﬁed in bytes, determines whether packets will be fragmented. Packets exceeding the 2346 byte setting will be fragmented before transmission. 2346 is the default setting.WMM is QoS for your wireless network. This will improve the quality of video and voice applications for your wireless clients.Check this box to reduce the guard interval time therefore increasing the data capacity. However, it’s less reliable and may create higher data loss.

32D-Link DAP-1350 User ManualSection 3 - ConﬁgurationUser LimitCheck the Enable User Limit box to enable this feature.Enter the maximum number of clients, between 1 and 32.Click Save Settings to save and activate the new changes.Enable User Limit:User Limit:Save Settings:Enter the maximum number of wireless clients that can connect at one time to your access point.

33D-Link DAP-1350 User ManualSection 3 - ConﬁgurationPassword:Verify Password:Enable Graphical Authentication:Enter a new password for the Administrator Login Name. The administrator can make changes to the settings.Enter the same password that you entered in the previous textbox in order to conﬁrm its accuracy.Enables a challenge-response test to require users to type letters or numbers from a distorted image displayed on the screen to prevent online hackers and unauthorized users from gaining access to your router’s network settings. This feature is disabled by default.AdminThis page will allow you to change the Administrator password. The administrator password has read/write access.

34D-Link DAP-1350 User ManualSection 3 - ConﬁgurationSave to Local Hard Drive:Upload from Local Hard Drive:Restore to Factory Default:Reboot the Device:Use this option to save the current access point conﬁguration settings to a ﬁle on the hard disk of the computer you are using. Click the Save button. You will then see a ﬁle dialog where you can select a location and ﬁle name for the settings. Use this option to load previously saved access point conﬁguration settings. Click Browse to ﬁnd a previously saved conﬁguration ﬁle. Then, click the Upload Settings button to transfer those settings to the access point. This option will restore all conﬁguration settings back to the settings that were in effect at the time the access point was shipped from the factory. Any settings that have not been saved will be lost, including any rules that you have created. If you want to save the current access point conﬁguration settings, use the Save button above. Note: Restoring the factory default settings will not reset the Wi-Fi Protected Status to Not Conﬁgured.Click to reboot the access point.System

35D-Link DAP-1350 User ManualSection 3 - ConﬁgurationBrowse:Upload:After you have downloaded the new ﬁrmware, click Browse to locate the ﬁrmware update on your hard drive. Click Upload to complete the ﬁrmware upgrade.Once you have a ﬁrmware update on your computer, use this option to browse for the ﬁle and then upload the information into the access point. FirmwareYou can upgrade the ﬁrmware of the access point here. Make sure the ﬁrmware you want to use is on the local hard drive of the computer. Click on Browse to locate the ﬁrmware ﬁle to be used for the update. Please check the D-Link support website for ﬁrmware updates at http://support.dlink.com. You can download ﬁrmware upgrades to your hard drive from this site.After you have downloaded the new language pack, click Browse to locate the language pack ﬁle on your hard drive. Click Upload to complete the language pack upgrade.Note: In most cases you must unzip the ﬁle ﬁrst before uploading.Language PackYou can change the language of the web UI by uploading available language packs.Browse:

36D-Link DAP-1350 User ManualSection 3 - ConﬁgurationTime Zone:Daylight Saving:Enable NTP Server:NTP Server Used:Date and Time:Select the Time Zone from the drop-down menu.To select Daylight Saving time manually, click the Enable Daylight Saving check box. Next use the drop-down menu to select a Daylight Saving Offset and then enter a start date and an end date for daylight saving time.NTP is short for Network Time Protocol. NTP synchronizes computer clock times in a network of computers. Check this box to use a NTP server. This will only connect to a server on the Internet, not a local server.Enter the NTP server or select one from the drop-down menu.To manually input the time, enter the values in these ﬁelds for the Year, Month, Day, Hour, Minute, and Second and then click Save Settings. You can also click the Copy Your Computer’s Time Settings button at the bottom of the screen.TimeThe Time Conﬁguration option allows you to conﬁgure, update, and maintain the correct time on the internal system clock. From this section you can set the time zone that you are in. Daylight Saving can also be conﬁgured to automatically adjust the time when needed.

37D-Link DAP-1350 User ManualSection 3 - ConﬁgurationEnter a name for your new schedule.Select a day, a range of days, or All Week to include every day.Check All Days or enter a start and end time for your schedule.Select On or Off from the drop-down menu. Click Add to save your schedule. You must click Save Settings at the top for your schedules to go into effect.The list of schedules will be listed here. Click the Edit icon to make changes or click the Delete icon to remove the schedule.Name:Days:Time:Wireless:Add:Schedule Rules List:SchedulesSchedules can be created for use with enforcing rules. For example, if you want to restrict web access to Mon-Fri from 3pm to 8pm, you could create a schedule selecting Mon, Tue, Wed, Thu, and Fri and enter a Start Time of 3pm and End Time of 8pm.

38D-Link DAP-1350 User ManualSection 3 - ConﬁgurationGeneral:LAN:Wireless LAN:Displays the access point’s time and ﬁrmware version.Displays the MAC address and the private (local) IP settings for the access point.Displays the wireless MAC address and your wireless settings such as SSID and Channel.Device InfoThis page displays the current information for the DAP-1350. It will display the LAN and wireless LAN information.

39D-Link DAP-1350 User ManualSection 3 - ConﬁgurationFirst Page:Last Page:Previous Page:Next Page:Clear Log:Log Settings:Refresh:This button directs you to the ﬁrst page of the log.This button directs you to the last page of the log.This button directs you to the previous page of the log.This button directs you to the next page of the log.This button clears all current log content.This button opens a new menu where you can conﬁgure the log settings.This button refreshes the log.LogsThe DAP-1350 keeps a running log of events and activities occurring on the AP. If the AP is rebooted, the logs are automatically cleared. You can save the log ﬁles under Log Setting.

40D-Link DAP-1350 User ManualSection 3 - ConﬁgurationStatisticsThe DAP-1350 keeps statistics of the trafﬁc that passes through it. You can view the amount of packets that pass through the LAN and wireless portions of the network. The trafﬁc counter will reset if the access point is rebooted.

41D-Link DAP-1350 User ManualSection 3 - ConﬁgurationWirelessThe wireless section allows you to view the wireless clients that are connected to your wireless access point.Connection Time:MAC Address:Displays the amount of time the wireless client has been connected to the access point.The Ethernet ID (MAC address) of the wireless client.

42D-Link DAP-1350 User ManualSection 3 - ConﬁgurationHelp

43D-Link DAP-1350 User ManualSection 3 - ConﬁgurationWireless Client ModeIf you wish to change the default settings or optimize the performance of the DAP-1350, you may use the web-based conﬁguration utility.To access the conﬁguration utility, open a web browser such as Internet Explorer and enter dlinkap or 192.168.0.50 in the address ﬁeld.Type Admin and then enter your password. Leave the password blank by default..If you get a Page Cannot be Displayed error, please refer to the Troubleshooting section for assistance.Change the mode selector to Client on the device. Connect an Ethernet cable from the Ethernet port on the DAP-1350 to a computer for conﬁguration.

44D-Link DAP-1350 User ManualSection 3 - ConﬁgurationThis Wizard is designed to assist you in conﬁguring your DAP-1350 as a wireless client.If you want to change the admin account password, enter a new password and click Next. It is strongly recommended to change your password.Wireless Setup WizardEnter the Device Name of the AP and click Next to continue. It is recommended to change the Device Name if there is more than one D-Link device within the same wireless network. Click the Launch Wireless Setup Wizard button to use the wizard to setup your network.

45D-Link DAP-1350 User ManualSection 3 - ConﬁgurationFor PBC (Push Button Conﬁguration), skip to the next page. Select PIN to connect your wireless device with WPS. You may click Generate New PIN to use a different PIN number. Click Connect to start the WPS scan.Within 2 minutes, enter the PIN number into the other device you want to connect to.Select Auto as the conﬁguration method only if your wireless device supports Wi-Fi Protected Setup (WPS). For Manual setup, skip to the next page.Click Next to continue.

46D-Link DAP-1350 User ManualSection 3 - ConﬁgurationSelect PBC to use the Push Button Conﬁguration to connect to your network. Click Connect to continue.Note: You may also press the WPS button located on the side of the DAP-1350 instead of running this wizard.On the device you want to connect to, start the PBC process on the device. You will have 2 minutes to start the PBC process on both devices.

47D-Link DAP-1350 User ManualSection 3 - ConﬁgurationSelect Manual conﬁguration to setup your network manually.Click Next to continue.Enter the network name (SSID) of the network you want to connect to. If you do not know the exact name or would like to search for the wireless network, click Site Survey.Find your access point from the list, click the radio button in the right column, and click Connect.

48D-Link DAP-1350 User ManualSection 3 - ConﬁgurationChoose which Security Mode you want to use and click Next to continue.If you select WEP, choose the key type (ASCII or HEX), the key size (64 or 128-bit), and enter the wireless security password. Click Next to complete the Setup Wizard.If you select WPA or WPA2, enter the wireless security password. Click Next to complete the Setup Wizard.

49D-Link DAP-1350 User ManualSection 3 - ConﬁgurationThe Wireless Setup Wizard is complete. Click Finish to reboot the device.

50D-Link DAP-1350 User ManualSection 3 - ConﬁgurationManual Wireless SetupWireless Mode:Site Survey:Wireless Type:Wireless NetworkName:Wireless Channel:802.11 Mode:Channel Width:Transmission Rate:Wireless MAC Clone:Wireless SecurityMode:WPS:Wireless Client Mode is selected.Click Site Survey to display a list of wireless networks in your area. You may select the wireless access point to connect to.Select Infrastructure if connecting to an access point or wireless router, or select Ad-Hoc if connecting to another wireless client.Enter the SSID of the wireless network you want to connect to. If you do not know for sure, click Site Survey and select it from the list, if available.The channel will automatically change to the channel of the AP you are connected to. Select the appropriate 802.11 mode based on the wireless clients in your network. Select Mixed 802.11b/g, 802.11n Only, or Mixed 802.11b/g/n from the drop-down menu.Select the Channel Width:Auto 20/40 - Select if you are using both 802.11n and non-802.11n wireless devices.20MHz - Select if you are not using any 802.11n wireless clients.Select the transmission rate. It is strongly suggested to use the Auto setting for optimal performance.You can clone the MAC address of the device connected via Ethernet to the DAP-1350. Select a wireless security setting. Options are None, WEP, WPA, or WPA2. See the Wireless Security section in this manual for a detailed explanation of the wireless security options.Select enable if you want to conﬁgure the DAP-1350 with Wi-Fi Protection setup.

51D-Link DAP-1350 User ManualSection 3 - ConﬁgurationLAN SettingsThis section will allow you to change the local network settings of the access point and to conﬁgure the DHCP settings.LAN Connection Type:IP Address:Subnet Mask:Default Gateway:Device Name:Use the drop-down menu to select Dynamic IP (DHCP) to automatically obtain an IP address on the LAN/private network or select Static IP to manually enter the IP settings.192.168.0.50 is the default IP Address of the DAP-1350.255.255.255.0 is the default subnet mask. All devices on the network must have the same subnet mask to communicate on the network.Enter the IP Address of the gateway in your network.Enter the Device Name of the AP. It is recommended to change the Device Name if there is more than one D-Link device within the subnet.

52D-Link DAP-1350 User ManualSection 3 - ConﬁgurationLogoutThis section will allow you to change the local network settings of the access point and to conﬁgure the DHCP settings.

53D-Link DAP-1350 User ManualSection 3 - ConﬁgurationAdvanced WirelessTransmit Power:RTS Threshold:Fragmentation Threshold:Short GI:Sets the transmit power of the antennas.Note: Transmit power is regulated by international standard. Users are forbidden to change its maximum limit.This value should remain at its default setting of 2346. If inconsistent data ﬂow is a problem, only a minor modiﬁcation should be made.The fragmentation threshold, which is speciﬁed in bytes, determines whether packets will be fragmented. Packets exceeding the 2346 byte setting will be fragmented before transmission. 2346 is the default setting.Check this box to reduce the guard interval time therefore increasing the data capacity. However, it’s less reliable and may create higher data loss.

54D-Link DAP-1350 User ManualSection 3 - ConﬁgurationEnter a new password for the Administrator Login Name. The administrator can make changes to the settings.Enter the same password that you entered in the previous textbox in order to conﬁrm its accuracy.Enables a challenge-response test to require users to type letters or numbers from a distorted image displayed on the screen to prevent online hackers and unauthorized users from gaining access to your router’s network settings.AdminThis page will allow you to change the Administrator password. The administrator password has read/write access.Password:Verify Password:Enable Graphical Authentication:

55D-Link DAP-1350 User ManualSection 3 - ConﬁgurationSave to Local Hard Drive:Load from Local Hard Drive:Restore to Factory Default:Reboot the Device:Use this option to save the current access point conﬁguration settings to a ﬁle on the hard disk of the computer you are using. Click the Save button. You will then see a ﬁle dialog where you can select a location and ﬁle name for the settings. Use this option to load previously saved access point conﬁguration settings. Click Browse to ﬁnd a previously saved conﬁguration ﬁle. Then, click the Upload Settings button to transfer those settings to the access point. This option will restore all conﬁguration settings back to the settings that were in effect at the time the access point was shipped from the factory. Any settings that have not been saved will be lost, including any rules that you have created. If you want to save the current access point conﬁguration settings, use the Save button above. Note: Restoring the factory default settings will not reset the Wi-Fi Protected Status to Not Conﬁgured.Click to reboot the access point.System

56D-Link DAP-1350 User ManualSection 3 - ConﬁgurationBrowse:Upload:After you have downloaded the new ﬁrmware, click Browse to locate the ﬁrmware update on your hard drive. Click Upload to complete the ﬁrmware upgrade.Once you have a ﬁrmware update on your computer, use this option to browse for the ﬁle and then upload the information into the access point. FirmwareYou can upgrade the ﬁrmware of the access point here. Make sure the ﬁrmware you want to use is on the local hard drive of the computer. Click on Browse to locate the ﬁrmware ﬁle to be used for the update. Please check the D-Link support website for ﬁrmware updates at http://support.dlink.com. You can download ﬁrmware upgrades to your hard drive from this site.After you have downloaded the new language pack, click Browse to locate the language pack ﬁle on your hard drive. Click Upload to complete the language pack upgrade.Note: In most cases you must unzip the ﬁle ﬁrst before uploading.Language PackYou can change the language of the web UI by uploading available language packs.Browse:

57D-Link DAP-1350 User ManualSection 3 - ConﬁgurationTime Zone:Daylight Saving:Enable NTP Server:NTP Server Used:Date and Time:Select the Time Zone from the drop-down menu.To select Daylight Saving time manually, click the Enable Daylight Saving check box. Next use the drop-down menu to select a Daylight Saving Offset and then enter a start date and an end date for daylight saving time.NTP is short for Network Time Protocol. NTP synchronizes computer clock times in a network of computers. Check this box to use a NTP server. This will only connect to a server on the Internet, not a local server.Enter the NTP server or select one from the drop-down menu.To manually input the time, enter the values in these ﬁelds for the Year, Month, Day, Hour, Minute, and Second and then click Save Settings. You can also click the Copy Your Computer’s Time Settings button at the bottom of the screen.TimeThe Time Conﬁguration option allows you to conﬁgure, update, and maintain the correct time on the internal system clock. From this section you can set the time zone that you are in. Daylight Saving can also be conﬁgured to automatically adjust the time when needed.

58D-Link DAP-1350 User ManualSection 3 - ConﬁgurationGeneral:LAN:Wireless LAN:Displays the access point’s time and ﬁrmware version.Displays the MAC address and the private (local) IP settings for the access point.Displays the wireless MAC address and your wireless settings such as SSID and Channel.Device InfoThis page displays the current information for the DAP-1350. It will display the LAN and wireless LAN information.

59D-Link DAP-1350 User ManualSection 3 - ConﬁgurationFirst Page:Last Page:Previous Page:Next Page:Clear Log:Log Settings:Refresh:This button directs you to the ﬁrst page of the log.This button directs you to the last page of the log.This button directs you to the previous page of the log.This button directs you to the next page of the log.This button clears all current log content.This button opens a new menu where you can conﬁgure the log settings.This button refreshes the log.LogsThe DAP-1350 keeps a running log of events and activities occurring on the AP. If the AP is rebooted, the logs are automatically cleared. You can save the log ﬁles under Log Setting.

60D-Link DAP-1350 User ManualSection 3 - ConﬁgurationStatisticsThe DAP-1350 keeps statistics of the trafﬁc that passes through it. You can view the amount of packets that pass through the LAN and wireless portions of the network. The trafﬁc counter will reset if the access point is rebooted.

61D-Link DAP-1350 User ManualSection 3 - ConﬁgurationHelp

62D-Link DAP-1350 User ManualSection 3 - ConﬁgurationRouter ModeIf you wish to change the default settings or optimize the performance of the DAP-1350, you may use the web-based conﬁguration utility.To access the conﬁguration utility, open a web browser such as Internet Explorer and enter dlinkap or 192.168.0.50 in the address ﬁeld.Type Admin and then enter your password. Leave the password blank by default..If you get a Page Cannot be Displayed error, please refer to the Troubleshooting section for assistance.Change the mode selector to Router on the device. Connect an Ethernet cable from the Ethernet port on the DAP-1350 to your broadband modem. You will need to connect wirelessly to the DAP-1350 to conﬁgure it.

63D-Link DAP-1350 User ManualSection 3 - ConﬁgurationClick Launch Internet Connection Setup Wizard to begin.If you want to enter your settings without running the wizard, click Manual Internet Conﬁguration Setup and skip to page 65.Setup WizardClick Next to continue.Create a new password and then click Next to continue.

64D-Link DAP-1350 User ManualSection 3 - ConﬁgurationSelect your time zone from the drop-down menu and then click Next to continue.Select the type of Internet connection you use and then click Next to continue.

65D-Link DAP-1350 User ManualSection 3 - ConﬁgurationIf you selected Dynamic, you may need to enter the MAC address of the computer that was last connected directly to your modem. If you are currently using that computer, click Clone Your PC’s MAC Address and then click Next to continue.The Host Name is optional but may be required by some ISPs. The default host name is the device name of the Router and may be changed.Click Connect to save your settings. Once the router is ﬁnished rebooting, click Continue. Please allow 1-2 minutes to connect. Close your browser window and reopen it to test your Internet connection. It may take a few tries to initially connect to the Internet.

66D-Link DAP-1350 User ManualSection 3 - ConﬁgurationInternet SetupIf you opt to set up your Internet connection manually, you will be redirected to a WAN page that allows you to select your Internet type and enter the correct conﬁguration parameters.Select your Internet connection type using the “My Internet Connection is” drop-down menu.Click the Save Settings button when you have conﬁgured the connection.

67D-Link DAP-1350 User ManualSection 3 - ConﬁgurationDynamic IP (DHCP)Select Dynamic IP(DHCP) to obtain IP Address information automatically from your ISP. Select this option if your ISP does not give you any IP number to use. This option is commonly used for Cable modem services.Host Name:Use Unicasting:DNS Server:MTU:MAC Address:The Host Name is optional but may be required by some ISPs.Select if you are having problems obtaining an IP address from your DHCP server.Enter the Primary and Secondary DNS server IP address assigned by your ISP. You may need to change the MTU (Maximum Transmission Unit) for optimal performance with your speciﬁc ISP. The default MTU size is 1500.The default MAC address is set to the Ethernet MAC address your DAP-1350. You can click the Clone Your PC’s MAC Address button to replace the AP’s MAC address with the MAC address of the PC that you used to register with your ISP. It is not recommended that you change the default MAC address unless required by your ISP.

68D-Link DAP-1350 User ManualSection 3 - ConﬁgurationStatic IPSelect Static IP if all WAN IP information is provided to you by your ISP. You will need to enter in the IP address, subnet mask, gateway address, and DNS address(es) provided to you by your ISP.IP Address:Subnet Mask:Default Gateway:Primary DNS Server:Secondary DNS Server:MTU:Clone MAC Address:Enter the IP Address provided by your ISP (Internet Service Provider).255.255.255.0 is the default subnet mask. All devices on the network must have the same subnet mask to communicate on the network.Enter the IP Address of the gateway in your network.Enter the Primary DNS (Domain Name System) server IP address assigned by your ISP.Enter the Secondary DNS (optional) server IP address assigned by your ISP.You may need to change the MTU (Maximum Transmission Unit) for optimal performance with your speciﬁc ISP. The default MTU size is 1500. The default MAC address is set to the MAC address on the AP (Access Point). You can click the Clone Your PC’s MAC Address button to replace the AP’s MAC address with the MAC address of your Ethernet card. It is not recommended that you change the default MAC address unless required by your ISP.

69D-Link DAP-1350 User ManualSection 3 - ConﬁgurationPPPoESelect PPPoE (Point-to-Point Protocol over Ethernet) if your ISP uses a PPPoE connection. Your ISP will provide you with a username and password. This option is typically used for DSL services. Make sure to remove your PPPoE software from your computer. The software is no longer needed and will not work through the DAP-1350.Username:Password:Service Name:Reconnect Mode:Maximum Idle Time:DNS Servers:MTU:Clone MAC Address:Enter your PPPoE user name.Enter your PPPoE password and then retype the password in the next box.Enter the ISP Service Name (optional).Select Always on, On Demand or Manual.Enter the time (in minutes) where the router will disconnect if idle for the time speciﬁed. Enter the Primary and Secondary DNS (Domain Name System) server IP address assigned by your ISP.You may need to change the MTU (Maximum Transmission Unit) for optimal performance with your speciﬁc ISP. The default MTU size is 1400.The default MAC address is set to the MAC address on the AP (Access Point). You can click the Clone Your PC’s MAC Address button to replace the AP’s MAC address with the MAC address of your Ethernet card. It is not recommended that you change the default MAC address unless required by your ISP.

70D-Link DAP-1350 User ManualSection 3 - ConﬁgurationPPTPChoose PPTP (Point-to-Point Tunneling Protocol) if your ISP uses a PPTP connection. Your ISP will provide you with a username and password. This option is typically used for DSL services.PPTP IP Address:PPTP Subnet Mask:PPTP Server IP Address:Username:Password:Reconnect Mode:Maximum Idle Time:DNS Servers:MTU:Clone MAC Address:Enter the IP address (Static PPTP only).Enter the subnet mask.Enter the Server IP Address provided by your ISP.Enter your PPTP username.Enter your PPTP password and then retype the password in the next box.Select Always on, On Demand or Manual.Enter the time (in minutes) where the router will disconnect if idle for the time speciﬁed. Enter the Primary and Secondary DNS (Domain Name System) server IP address assigned by your ISP.You may need to change the MTU (Maximum Transmission Unit) for optimal performance with your speciﬁc ISP. The default MTU size is 1400.The default MAC address is set to the MAC address on the AP (Access Point). You can click the Clone Your PC’s MAC Address button to replace the AP’s MAC address with the MAC address of your Ethernet card. It is not recommended that you change the default MAC address unless required by your ISP.

71D-Link DAP-1350 User ManualSection 3 - ConﬁgurationL2TPChoose L2TP (Point-to-Point Tunneling Protocol) if your ISP uses a L2TP connection. Your ISP will provide you with a username and password. This option is typically used for DSL services.PPTP IP Address:PPTP Subnet Mask:PPTP Server IP Address:Username:Password:Reconnect Mode:Maximum Idle Time:DNS Servers:MTU:Clone MAC Address:Enter the IP address (Static PPTP only).Enter the subnet mask.Enter the Server IP Address provided by your ISP.Enter your PPTP username.Enter your PPTP password and then retype the password in the next box.Select Always on, On Demand or Manual.Enter the time (in minutes) where the router will disconnect if idle for the time speciﬁed. Enter the Primary and Secondary DNS (Domain Name System) server IP address assigned by your ISP.You may need to change the MTU (Maximum Transmission Unit) for optimal performance with your speciﬁc ISP. The default MTU size is 1400.The default MAC address is set to the MAC address on the AP (Access Point). You can click the Clone Your PC’s MAC Address button to replace the AP’s MAC address with the MAC address of your Ethernet card. It is not recommended that you change the default MAC address unless required by your ISP.

72D-Link DAP-1350 User ManualSection 3 - ConﬁgurationWireless Setup WizardYou may click Wireless Network Setup Wizard to quickly conﬁgure your router. Refer to the next page.To set up your wireless network, click Add Wireless Device With WPS and skip to page 76.If you want to enter your settings without running the wizard, click Manual Wireless Network Setup and skip to page 77.

73D-Link DAP-1350 User ManualSection 3 - ConﬁgurationType your desired wireless network name (SSID). Automatically: Select this option to automatically generate the router’s network key and click Next.Manually: Select this option to manually enter your network key and click Next.If you selected Automatically, the summary window will display your settings. Write down the security key and enter this on your wireless clients. Click Save to save your settings.

74D-Link DAP-1350 User ManualSection 3 - ConﬁgurationIf you selected Manually assign a network key as the conﬁguration method, enter your network key. This key must be entered on your wireless clients.Check the Use WPA encryption instead of WEP box to use WPA Encryption instead of WEP.Click Next to continue. For WEP encryption, enter a Network Key exactly 5 or 13 characters long or exactly 10 or 26 characters using 0-9 and A-F.Click Next to continue.

75D-Link DAP-1350 User ManualSection 3 - ConﬁgurationIf you select WPA, enter the wireless security password (8-32 characters). Click Next to complete the Setup Wizard.Click Next to continue. The summary screen will appear. Click Save to continue. The summary screen will appear.Click Save to continue.

76D-Link DAP-1350 User ManualSection 3 - ConﬁgurationFrom the Setup > Wireless Settings screen, click Add Wireless Device with WPS.Add Wireless Device with WPS WizardPIN: Select this option to use PIN method. In order to use this method you must know the wireless client’s 8 digit PIN and click Connect.PBC: Select this option to use PBC (Push Button) method to add a wireless client. Click Connect.Select Auto to add a wireless client using WPS (Wi-Fi Protected Setup). Once you select Auto and click Connect, you will have a 120 second time limit to apply the settings to your wireless client(s) and successfully establish a connection. If you select Manual, a settings summary screen will appear. Write down the security key and enter this on your wireless clients.

77D-Link DAP-1350 User ManualSection 3 - ConﬁgurationWireless SettingsEnable Wireless:Wireless NetworkName:Wireless Mode:Enable Auto Channel Scan:Wireless Channel:Transmission Rate:Channel Width: Visibility Status:Wireless SecurityMode:Select this to turn the Wi-Fi module on and off. Use the drop-down box to select if you want to use a schedule. Click Add New Schedule to add or change a schedule.Enter a wireless network name (SSID) for your network (up to 32 characters).Select the appropriate 802.11 mode based on the wireless clients in your network. The drop-down menu options are 802.11g Only, Mixed 802.11b/g, 802.11b Only, 802.11n Only, or Mixed 802.11b/g/n.Check this box to have the device automatically scan for the best available channel.Select a wireless channel. It is recommended to use channels 1,6, or 11. This option will be disabled if the Auto Channel Scan box is checked.Select the transmission rate. It is strongly suggested to use the Auto setting for optimal performance.Select the appropriate channel width between 20MHz or Auto 20/40MHz from the drop-down menu.Select Invisible if you do not want the SSID of your wireless network to be broadcast by the DAP-1350. If Invisible is selected, the SSID of the DAP-1350 will not be seen by Site Survey utilities so your wireless clients will have to know the SSID of your DAP-1350 in order to connect to it.Select a wireless security setting. Options are None, WEP, WPA, or WPA2. Refer to the Wireless Security section of this manual for a detailed explanation of the wireless security options.

78D-Link DAP-1350 User ManualSection 3 - ConﬁgurationNetwork SettingsEnter the IP address of the router. The default IP address is 192.168.0.1.If you change the IP address, once you click Apply, you will need to enter the new IP address in your browser to get back into the conﬁguration utility.Enter the Subnet Mask. The default subnet mask is 255.255.255.0.Enter the Domain name (Optional).Uncheck the box to transfer the DNS server information from your ISP to your computers. If checked, your computers will use the router for a DNS server.IP Address:Subnet Mask:Local Domain:Enable DNS Relay:

79D-Link DAP-1350 User ManualSection 3 - ConﬁgurationCheck this box to enable the DHCP server on your router. Uncheck to disable this function.Enter the starting and ending IP addresses for the DHCP server’s IP assignment.Note: If you statically (manually) assign IP addresses to your computers or devices, make sure the IP addresses are outside of this range or you may have an IP conﬂict. The length of time for the IP address lease. Enter the Lease time in minutes.Refer to the next page for the DHCP Reservation function.Enable DHCP Server:DHCP IP Address Range:Lease Time:Add DHCP Reservation:DHCP Server SettingsDHCP stands for Dynamic Host Control Protocol. The DAP-1350 has a built-in DHCP server. The DHCP Server will automatically assign an IP address to the computers on the LAN/private network. Be sure to set your computers to be DHCP clients by setting their TCP/IP settings to “Obtain an IP Address Automatically.” When you turn your computers on, they will automatically load the proper TCP/IP settings provided by the DAP-1350. The DHCP Server will automatically allocate an unused IP address from the IP address pool to the requesting computer. You must specify the starting and ending address of the IP address pool.

Navigation menu